Instruction/ maintenance manual of the product IL-90MV Abit
Go to page of 72
Introduction Hardware Setup BIOS Setup Driver & Utility CD Appendix iL-90MV Motherboard Intel Socket 478 (Core Duo) User’s Manual Intel Socket 478 (Core Duo) Micro ATX Motherboard Intel ViiV Technology Certified Intel 945GT/ICH7m-DH Intel GMA 950 HDMI 1.
iL-90MV User’s Manual English, 2 nd Edition August, 2006 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual.
Introduction Contents 1. Introduction ..................................................................... 1-1 Hardware Setup BIOS Setup Driver & Utility CD Appendix 1.1 Features & Specifications ..............................................
3.6 PnP/PCI Configurations .............................................................. 3-20 3.7 PC Health Status ........................................................................ 3-22 3.8 Load Fail-Safe Defaults .............................
Introduction 1. Introduction 1.1 Features & Specifications CPU • Designed for Intel ® Core Duo/Solo, Core 2 Duo socket 478 processors with 667/533MHz FSB • Supports Enhanced Intel Speedstep .
• 1x FP-Audio header • 1x CD-IN connector Rear Panel I/O • 1x VGA connector • 1x PS/2 Keyboard connector • 1x PS/2 Mouse connector • 1x HDMI 1.
Introduction 1.2 Motherboard Layout iL-90MV 1-3.
1-4 iL-90MV.
Hardware Setup iL-90MV 2-1 2. Hardware Setup In this chapter we will elaborate all the information you need upon installing this motherboard to your computer system. ※ Always power off the computer and unplug the AC power cord before adding or removing any peripheral or component.
To install this motherboard: 1. Locate all the screw holes on the motherboard and the chassis base. 2. Place all the studs or spacers needed on the chassis base and have them tightened. 3. Face the motherboard’s I/O ports toward the chassis’s rear panel.
Hardware Setup iL-90MV 2-3 2.3.1 CMOS Memory Clearing Header and Backup Battery The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b) you forgot the supervisor or user.
CMOS Backup Battery: An onboard battery saves the CMOS memory to keep the BIOS information stays on even after disconnected your system with power source.
Hardware Setup iL-90MV 2-5 2.3.2 Wake-up Headers These headers use a jumper cap to enable/disable the wake-up function. • USB-PWR1: Pin 1-2 shorted (default): Disable wake-up function support at USB1 port. Pin 2-3 shorted: Enable wake-up function support at USB1 port.
2.4 Connecting Chassis Components 2.4.1 ATX Power Connectors These connectors provide the connection from an ATX power supply. As the plugs from the power supply fit in only one orientation, find the correct one and push firmly down into these connectors.
Hardware Setup iL-90MV 2-7 2.4.2 Front Panel Switches & Indicators Headers This header is used for connecting switches and LED indicators on the chassis front panel. Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below stands for positive polarity for the LED conn ection.
2.4.3 FAN Power Connectors These connectors each provide power to the cooling fans installed in your system. • CPUFAN1: CPU Fan Power Connector • SYSFAN1: System Fan Power Connector • AUXFAN1~2: Auxiliary Fan Power Connector ※ These fan connectors are not jumpers.
Hardware Setup iL-90MV 2-9 2.5 Installing Hardware ※ DO NOT scratch the motherboard when installing hardware. An accidentally scratch of a tiny surface-mount component may seriously damage the motherboard. 2.5.1 CPU Socket 478 (Core Duo) ※ Be cautious when installing CPU into this socket.
4. Peel off the protective film from the retention module. This will expose the adhesive sponge. 5. Face the retention module with the side of adhesive sponge toward the bottom side of the motherboard. Align the four screw holes from the retention module through the motherboard.
Hardware Setup iL-90MV 2-11 7. Carefully place the heatsink onto CPU socket in the direction of blowing its airflow toward rear panel. Use a cross-head screw driver to lock the four screws around the heatsink. 8. Lock the screws diagonally in the order of (1) (2) (3) (4).
2.5.2 DDR2 Memory Slots This motherboard provides two 240-pin DIMM slots for Dual Channel DDR2 667/533 memory modules with memory expansion size up to 2GB. ※ To reach the optimum performance in dual-channel configur ations, install DDR DIMM pairs at the same density, DRAM technology and bus width for both slots.
Hardware Setup iL-90MV 2-13 2.6 Connecting Peripheral Devices 2.6.1 Floppy and IDE Disk Drive Connectors The FDC1 connector connects up to two floppy dr ives with a 34-wire, 2-connector floppy cable.
2.6.2 Serial ATA Connectors Each SATA connector serves as one single channel to connect one SATA device by a thin SATA cable. For more information on how to configure the function mode for SATA, please refer to the item “On-Chip SATA Controller” in the BIOS menu of “On-Chip IDE Device”.
Hardware Setup iL-90MV 2-15 2.6.3 Additional USB 2.0 Port Headers Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis.
2.6.5 Internal Audio Connectors This connector connects to the audio output of internal CD-ROM drive or add-on card. 2.6.6 Front Panel Audio Connection Header This header provides the front panel conn.
Hardware Setup iL-90MV 2-17 Driver Configuration for AC’97 audio connection: The audio driver is originally configured to support HD Audio. For AC’97 audio connection, you may: 1. Right-click the “Realtek HD Audio Manager” icon in system tray.
2.6.7 PCI Express X1 Add-on Slot This slot provides the connection of add-on cards that comply with PCI Express specifications. 2.6.8 PCI Add-on Slots These slots provide the connection of add-on cards that comply with PCI specifications.
Hardware Setup iL-90MV 2-19 2.7 Onboard Status Display 2.7.1 Power Source Indicators These indicators work as a reminding device to display the power status of this motherboard with power source connected. • 5VSB: This LED lights up when the power supply is connected with power source.
2.8 Connecting Rear I/O Devices The rear I/O part of this motherboard provides the following I/O ports: • VGA1: Connects to monitor input. • Mouse: Connects to PS/2 mouse. • Keyboard: Connects to PS/2 keyboard. • HDMI1: Connects to multimedia devices of HDMI protocol.
BIOS Setup iL-90MV 3-1 3. BIOS Setup This motherboard provides a programmable EEPRO M that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and periph erals.
3.1 Standard CMOS Features Phoenix – AwardBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Tue. Aug 1 2006 Item Help Time (hh:mm:ss) 12 : 34 : 56 ► IDE Channel 1 Master None ► IDE .
BIOS Setup iL-90MV 3-3 IDE Channel 1 Master/Slave, IDE Channel 2 Master/Slave, IDE Channel 3 Master/Slave, IDE Channel 4 Master/Slave Click <Enter> key to enter its submenu: Phoenix – Awar.
Cylinder This item configures the numbers of cylinders. Head This item configures the numbers of read/write heads. Precomp This item displays the number of cylinders at which to change the write timing. Landing Zone This item displays the number of cylinders specified as the landing zone for the read/write heads.
BIOS Setup iL-90MV 3-5 Total Memory This item displays the total memory available in the system..
3.2 Advanced BIOS Features Phoenix – AwardBIOS CMOS Setup Utility Advanced BIOS Features Quick Power on Self Test Enabled Item Help ► CPU Feature Press Enter ► Hard Disk Boot Priority Press Ente.
BIOS Setup iL-90MV 3-7 C1E Function This item appears only for certain processors with the C1E (Enhanced Halt State) Function. When set to [Enabled], the processor will further reduce the total power consumption. Execute Disable Bit This item appears only for certain processors with the Execute Disable Bit (XD bit) feature.
※ Don’t forget your password. If you forg et the password, you wi ll have to open the computer case and clear all informati on in the CMOS before you can start up the system.
BIOS Setup iL-90MV 3-9 3.3 Advanced Chipset Features Phoenix – AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable By SPD Item Help X - CAS Latency Time (tCL) Auto X - RAS#.
PCI Express Root Port Func Click <Enter> key to enter its submenu: Phoenix – AwardBIOS CMOS Setup Utility PCI Express Root Port Func PCI Express Slot 1 Auto Item Help PCIe Compliancy Mode v1.
BIOS Setup iL-90MV 3-11 An unmatched configuration will cause the display device abnormal. For example, an HDMI digital device connected to “HDMI Port” under the [DVI] selection will have no sound on the digital display, whereas a non-HDMI monitor connected to “HDMI Port” under the [Normal] selection will cause the screen flickering.
3.4 Integrated Peripherals Phoenix – AwardBIOS CMOS Setup Utility Integrated Peripherals ► On-Chip IDE Device Press Enter Item Help ► On-Chip PCI Device Press Enter ► Super-IO Device Press Ent.
BIOS Setup iL-90MV 3-13 IDE Bus Master This option enables or disables the IDE bus mastering capability under the DOS environment. On-Chip IDE-1 Controller This item selects whether to enable or disable the IDE-1 controller. On-Chip SATA Mode This item determines the mode for on-chip Serial ATA.
※ The option [Enhanced Mode] does not support the Windows 98/ME operating system. - PATA IDE Mode This item determines the function mode for “IDE1”connector. [IDE-1]: “IDE1” connector served as [Primary Master] and [Primary Slave] channel. The remaining “SATA1” and “SATA2” connectors are disabled.
BIOS Setup iL-90MV 3-15 - USB 2.0 Controller This option enables or disables the USB 2.0 controller. - USB Keyboard Support via Select [ BIOS ] (the default setting) for the legacy operating system (such as DOS) that does not support USB keyboard.
Onboard PCI Device Click <Enter> key to enter its submenu: Phoenix – AwardBIOS CMOS Setup Utility Onboard PCI Device IEEE 1394 Controller Enabled Item Help Network Controller Enabled - Inv.
BIOS Setup iL-90MV 3-17 3.5 Power Management Setup Phoenix – AwardBIOS CMOS Setup Utility Power Management Setup ACPI Suspend Type S3(Suspend To RAM) Item Help - Resume by USB From S3 Enabled Power Button Function Instant-Off CPU THRM-Throttling 50.
Wake Up by Wake# of PCIe When set to [Enabled], access through the add-on PCI Express card can remotely wake up the system that was in Soft-Off condition.
BIOS Setup iL-90MV 3-19 ※ The mouse wake up function can only be used with the PS/2 mouse, not with the COM port or USB type. Some PS/2 mice cannot wake up the system because of compatible problems. If the specs of y our keyboard are too old, it may fail to power on.
3.6 PnP/PCI Configurations Phoenix – AwardBIOS CMOS Setup Utility PnP/PCI Configurations Resources Controlled By Auto Item Help X - IRQ Resources Press Enter PCI/VGA Pallete Snoop Disbaled PCI Laten.
BIOS Setup iL-90MV 3-21 - IRQ Resources Click <Enter> key to enter its submenu: This item sets each system interrupt to either [PCI Device] or [Reserved].
3.7 PC Health Status Phoenix – AwardBIOS CMOS Setup Utility PC Health Status ► ABIT FanEQ Control Press Enter Item Help FAN Fail Alarm Selectable Disabled Shutdown When FAN Fail Disabled CPU Shutd.
BIOS Setup iL-90MV 3-23 CPU FanEQ Control This item allows you to control the CPUFAN speed. When set to [Enabled], the following items become selectable. - FanEQ Target Temp. This item sets the temperature mark for the “CPU FanEQ” function to take effect.
Back to PC Health Status Setup Menu FAN Fail Alarm Selectable This item selects the fan that will be monitored for malfunction. Shutdown When FAN Fail When set to [Enabled], the system will be shut down if the CPU fan is not running.
Driver & Utility CD iL-90MV 4-1 4. Driver & Utility CD The “Driver & Utility CD” that came packed with this motherboard contains drivers, utilities and software applications required for its basic and advanced features. Place the “Driver & Utility CD” into the CD-ROM dr ive in your system.
4.1 Intel Chipset Software Installation Utility This utility installs Windows [ INF ] files to the target system. These files outline to the operating system how to configure the Intel chipset co mponents in order to ensure all the features function properly.
Driver & Utility CD iL-90MV 4-3 4.2 Intel Matrix Storage Technology Driver This driver provides functionality for the on-chip SATA Controller. ※ This driver installation is necessary for connectors SATA1~SATA2 only when after having enabled the RAID function in the BIOS setup menu.
4.3 Intel Graphics Media Accelerator Driver This driver provides functionality for the on-chip Graphics Controller. To install this driver: 1. Click on the [Drivers] tab in the installation menu screen. 2. Click the [Intel Graphics Media Accelerator Driver] item.
Driver & Utility CD iL-90MV 4-5 4.3.1 Tips on HDMI application 1. Connects to your HDMI device from the connector “HDMI1” only with an HDMI-to-HDMI cable. DO NOT connect with an HDMI-to-DVI cable. 2. Connect your HDMI digital device to port “HDMI1” located at the rear I/O panel of this motherboard.
(2) If it does, uncheck the item “ Hide modes that this monitor cannot display ” in the “Monitor settings” via the path: [Control Panel] [Display Properties] [Settings] [Advanced] [Monitor]. (3) Now you can raise the screen resolution from the [Display Properties] to the one of your HDMI digital device.
Driver & Utility CD iL-90MV 4-7 6. Also, please remember that you will have to re-configure the “Display Device” every time after disconnecting HDMI cable.
4.4 Realtek Audio Driver This driver provides functionality for the onboard High Definition Audio Codec. To install this driver: 1. Click on the [Drivers] tab in the installation menu screen. 2. Click the [Audio Driver] item. The installation screen appears: 3.
Driver & Utility CD iL-90MV 4-9 4.5 Intel PRO Network Connections Driver This driver provides functionality for the onboard Intel Gigabit Network Controller. To install this driver: 1. Click on the [Drivers] tab in the installation menu screen. 2.
4.7 Intel SATA Driver Disk Maker This procedure is necessary if you want to install operating system to a RAID configuration connected among “SATA1~SATA2” connectors: 1. Prepare a 3.5” floppy disk drive and connect it to “FDC1” connector on this motherboard.
Driver & Utility CD iL-90MV 4-11 4.8 ABIT EQ (The Hardware Doctor Utility) ABIT EQ is a self-diagnostic system for PC based on motherboards designed and manufactured by ABIT Computer Corporation. It will protect PC Hardware by monitoring critical items of Power Supply Voltage, CPU & System Fans Speed, and CPU & System Temperature.
5. Execute the ABIT EQ by entering the Windows Menu [Start] [All Programs] [ABIT] [ABIT EQ]. 6. ABIT EQ shows you the status of Voltage, Fan Speed, and Temperature readings as well.
Driver & Utility CD iL-90MV 4-13 4.9 FlashMenu (BIOS Update Utility) ABIT FlashMenu is the most stable Windows-ba sed BIOS flash available. No more worries from crashing. With one click of BIOS updating, ABIT users can flash their BIOS more easily and in less time.
4-14 iL-90MV.
Appendix iL-90MV 5-1 5. Appendix 5.1 Troubleshooting (How to Get Technical Support?) 5.1.1 Q & A Q: Do I need to clear the CMOS before I use a new motherboard to assemble my new computer system? A: Yes, we highly recommend that you clear th e CMOS before installing a new motherboard.
Step 3. The same procedure as Step 2, but while discharging the CMOS data, pull out the ATX power connectors from motherboard and remove the button battery during CMOS discharge.
Appendix iL-90MV 5-3 • CPU : Type in the brand name and the speed (MHz) of your CPU. (Illustrate the over-clocking status if you had done so.) Example: Intel 650 3.4GHz (OC FSB=220MHz) • Memory brand: Type in the brand and model name of your memory module.
5.1.2 Technical Support Form 5-4 iL-90MV Region: E-mail: First name: Last Name: Subject: Motherboard: BIOS Version: CPU: Memory brand: Memory size: Memory configuration: Graphics card: Graphics driver.
Appendix iL-90MV 5-5 5.1.3 Universal ABIT Contact Information Taiwan Head Office Universal ABIT Co., Ltd. No. 323, Yang Guang St., Neihu, Taipei, 114, Taiwan Tel: 886-2-8751-3380 Fax: 886-2-8751-3381 Sales: sales@abit.com.tw Marketing: market@abit.com.
P/N: 4310-0000-37 Rev. 2.00 http://www.abit.com.tw.
An important point after buying a device Abit IL-90MV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Abit IL-90MV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Abit IL-90MV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Abit IL-90MV you will learn all the available features of the product, as well as information on its operation. The information that you get Abit IL-90MV will certainly help you make a decision on the purchase.
If you already are a holder of Abit IL-90MV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Abit IL-90MV.
However, one of the most important roles played by the user manual is to help in solving problems with Abit IL-90MV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Abit IL-90MV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
