Instruction/ maintenance manual of the product SD7-533 Abit
Go to page of 90
Copyright and W arranty Notice The information in thi s document is subject to change without notice and does not repres ent a commitment on part of the vendor , who assumes no lia bility or re sponsibili ty for an y e rrors t hat m ay app ear in t his m anual.
.
4200- 0260-02 Rev. 1. 01 SD7-533 Motherb oard User’s Manual Index CHAPTER 1. INTRODUCTION O F SD 7-533 FEATURE S...................... 1-1 1-1. F EATURES O F SD7- 533 M OTHERBOARD ............................................................... 1-1 1-2.
SD7- 533 Moth erboard.
Intro duction of SD7- 533 Featur es User’ s Manual 1-1 Chapter 1. Introduct ion of SD 7-533 Fe atures 1-1. Features of SD7-533 Motherboard This m othe rboard is des igned for use w ith Intel’ s latest g ene ration o f Pe ntium ® 4 478 pins proces sors.
Chapter 1 SD7- 533 Moth erboard 1-2 ensurin g a safe computing envi ronment. 1-2. Specifications 1. Proces sor ! Support s Intel ® Pe ntium ® 4 socket 478 p rocess or wit h 400 MHz (100 MHz Quad Data Rate) CPU fro nt side bus ! Support s future 40 0 MHz FSB proc essors for th e Intel ™ Pentium ™ 4 proce ssors 2.
Intro duction of SD7- 533 Featur es User’ s Manual 1-3 7. Misce llane ous ! ATX form factor ! One AGP slot, five PC I slots ! Buil t-in I rDA T X/RX he ader ! Tw o built-in S M-Bus heade r ! Hardwar.
Chapter 1 SD7- 533 Moth erboard 1-4 1-4. Layout Diagram for SD7-533 Figu re 1- 1. SD 7-533 m otherboard comp onent locat ion Figu re 1- 2. CA- 20 Back Panel D iagram.
Installing the Mother b oard User’ s Manual 2-1 Chapter 2. Installin g the Motherbo ard This S D7- 533 m othe rboar d not only prov i des all s tandar d equi pment fo r cla ssic pers onal co mpu ters, but also prov ides g reat f lexibil ity f or me eting futur e upgra de demands .
Chapter 2 SD7- 533 Moth erboard 2-2 2-1. Installing the M otherboard to t he Chassis Most comp uter c hassis w ill hav e a base on w hich there will be many moun ting holes tha t allow s the mothe rboard to be s ecure ly attache d and at t h e s ame time, pre vents shor t cir cuits.
Installing the Mother b oard User’ s Manual 2-3 2-2. Install Pentium ® 4 Proc essor and Heatsink Supporting-Base This m othe rboard pr ovide s a ZIF ( Z ero I nserti on F or ce) S ocket 4 78 to install I ntel ® Pentiu m ® 4 proc essor. The p rocessor you bou ght shou ld includ e a heat sink and cooli ng fan ki t along with .
Chapter 2 SD7- 533 Moth erboard 2-4 2-3. Installing System Memory This m othe rboard pr ovides three 184-pi n DDR DIMM s ites f or m emo ry e xpansio n. The DDR DIMM sock ets supp ort 8 Mx64 (64 MB ), 16 Mx64 (1 28 MB), 32 M x64 (256 MB), 64 Mx64 (512 MB ), and 128 Mx64 (1024 MB) or double d ensit y DDR DIMM modu les.
Installing the Mother b oard User’ s Manual 2-5 Step 4. Lo cate yo ur compute r’s 1 84-pin me mo ry e xpansion DD R DI MM socke t. Step 5. Inse rt the DD R DI MM module into the ex pansion s oc ket as show n in the illustra tion. No te ho w the mo dule is keyed to the s ocke t.
Chapter 2 SD7- 533 Moth erboard 2-6 Figu re 2- 6. All C onnect ors an d H ead ers for the SD7- 533 First , Let’ s see th e hea ders th at SD7 -533 us es, and wha t thei r func tions a re.
Installing the Mother b oard User’ s Manual 2-7 Cautio n If the pow er suppl y co nnectors are not pro perly attac hed to t he A TX pow er suppl y, the pow er suppl y or add-on cards may be dama ged. One e nd of AC pow er co re conne cts t o AT X power supply, an d the othe r end (A C plug) w ill plug into th e wall outlet .
Chapter 2 SD7- 533 Moth erboard 2-8 (3). FPIO2: IR Header (Infrared) The re is a specif ic orien t atio n for p ins 1 thro ugh 5, atta ch th e conn ector from the IR K IT or IR devi ce to th e FPIO2 h eader. This motherb oard su pport s standard IR transfer rates.
Installing the Mother b oard User’ s Manual 2-9 (6). FPIO 3 (U SB 3/4) and FP IO4 (U SB 5/6) H eaders: Add itional USB P lugs H eader These h ead ers are fo r conn ecti ng the add iti onal USB port pl ugs. Each con nector can pr ovid e two additio nal USB plugs for a total of fo ur ad ditional USB pl ugs .
Chapter 2 SD7- 533 Moth erboard 2-10 (8). FP IO1 H eaders: Th e Headers for C hassis’s Front Pane l Indicators and Switch es FPIO1 are for switc hes and indi cators for the chassis’s front panel, there are se vera l functions that come from this hea der.
Installing the Mother b oard User’ s Manual 2-11 Table 2-2. FPIO1 pin count name list PIN Na me Signi fican ce of signa l PIN Na me Signi fican ce of signa l PIN 1 HDD LED (+) PIN 2 SP-LED (+) PIN 3.
Chapter 2 SD7- 533 Moth erboard 2-12 (10). I DE1and IDE2 Connectors This m otherbo ard prov ides tw o IDE po rts (I DE1 & ID E2) to co nnect u p to four IDE de vices in U ltra DMA 100 mode by Ultr a DMA 66 ribbo n cabl es.
Installing the Mother b oard User’ s Manual 2-13 (11 ). 6 CHAUD1 Header : 6 Channels Audio Header You’ll s ee th is head er on SD 7-533 mother board.
Chapter 2 SD7- 533 Moth erboard 2-14 (13). CD1 an d AUX 1 Head ers These co nnec tors conn ect to th e audi o output of inter n al CD -RO M driv e or add- on car d. (14). SW1 a nd D15: Processor Defaul t Setting Switch and 5V Standby LED SW 1 is a pr oce ssor defa ult s etting switc h, used to set and test in our fact ory.
Installing the Mother b oard User’ s Manual 2-15 (15 ). P S/2 Keyboar d Connector Attach a PS/2 ke ybo ard connec tor to this 6-pin Di n-connec tor. If you use a n AT key board, yo u can go to a co mpute r stor e to purch ase an A T to AT X conve rter ada pter, t hen y ou can connec t your A T keybo ard to this conne ctor.
Chapter 2 SD7- 533 Moth erboard 2-16 Note This c hapter co ntains m any co lor draw ing diagra m an d photo s, we strongly r eco mmend y ou to re ad this c hap ter use the PDF file we gave yo u that sto re in the CD-Titl e. I t will pro vide yo u the bette r lo ok and cle arly co lor identify .
Intro ducing the BIO S User’ s Manual 3-1 Chapter 3. Introducin g the BIOS The BIO S is a prog ram loca ted on a Flash Me mory chip o n the mot herboard. T his pr ogr am w ill no t be lost when you tu rn the c omputer off. Th is p rogram is also ref erred to as the b oot progra m.
Chapter 3 SD7- 533 Moth erboard 3-2 In the BIOS Setup m ain menu of Fig ure 3- 1, yo u can see several options. W e will explain the se options step by step in the follo wing p ages of t his ch apter, but let u s firs t see a sh ort des cripti on of th e functi on key s you may use here : ! Press Esc to quit th e BIOS Setup .
Intro ducing the BIO S User’ s Manual 3-3 3-1. SOFT MENU ™ III Se tup The proce ssor can be setup thr ough a program mable switch ( SOFT MENU ™ III ) that re places the tradit ional m anual har dware config uratio n. This f eatur e allow s the user to more easily comple te the instal latio n proce dures .
Chapter 3 SD7- 533 Moth erboard 3-4 ! User Defined: &&&& Wa r n i n g &&&& The wro ng se ttings of the mul tiplie r and ex ternal clo ck in certa in circums tances may cause pro cessor damag e.
Intro ducing the BIO S User’ s Manual 3-5 Nor mally , we do not re comm end th at you use the “ Use r Defi ne ” opti on to setup p rocess or speed and PCI clock. T his optio n is fo r setu p of futur e proce ssor s whose s pecific ations ar e stil l unk now n.
Chapter 3 SD7- 533 Moth erboard 3-6 3-2. Standard CMOS F eatu res Setup M enu This co ntains t he bas ic co nfigurat ion par amete rs of the BIOS . The se param eters incl ude d ate, hour, VGA card, floppy di sk and HDD sett ings.
Intro ducing the BIO S User’ s Manual 3-7 IDE HDD Auto -Detectio n: Press the Enter key for the B I OS to au to detec t all deta iled pa rameters of the h ard disk d rivers (HDD). If auto d etecti on is su ccessfu l, th e correct values will b e shown in the rema ining it ems of thi s menu.
Chapter 3 SD7- 533 Moth erboard 3-8 " Capac ity: This item aut o displa ys your HDD size. Note th at thi s size is usua lly slight ly greater t han th e size given b y a disk ch eckin g program of a format ted disk. Note All the items bel ow ar e avail able w hen yo u set the ite m Primary IDE M a ster to Manual .
Intro ducing the BIO S User’ s Manual 3-9 Video : You ca n select t he VGA modes fo r your vi deo ada pter, f our o ptions are avai lable: EGA /VGA ) CGA 4 0 ) CGA 80 ) MONO. The d efault se tting is EG A/VGA . Halt On: You ca n select w hich ty pe of e rror will cause t h e s ys tem to halt.
Chapter 3 SD7- 533 Moth erboard 3-10 Figu re 3-4B . Adv anced BIOS Featu res Lower S creen Sh ot Virus W arning: This i tem can be set to Enable d or Dis abled, the defaul t setting be ing Disabled .
Intro ducing the BIO S User’ s Manual 3-11 Boot O ther D evice: Tw o optio ns ar e avail able: Disabl ed or Enabl ed. T he de fault set ting is Enabled . Thi s settin g allo ws the BIO S to try to boo t device s other than the three which are l isted in t he abo ve Fir st, Se cond an d Th ird Boot Devi ces.
Chapter 3 SD7- 533 Moth erboard 3-12 ! SETUP: When you choose Set up, a password is req ui red only when a ccessi ng the B IOS Setup. I f the cor rect passw ord is not g ive n, yo u can’t e nter t he BI OS setup me nu. ! SYSTEM: When you choose S ystem, a pa ssword is requir ed each ti me the compu ter boots up.
Intro ducing the BIO S User’ s Manual 3-13 Repor t No FDD For WIN 95: When u sing Wind ows ® 95 w ithout a fl oppy drive se t this item to Yes . Other wise, s et it to No . The de fault setti ng is No . Video B IOS Shadow: This option i s used to defi ne wheth er the B IOS on the vid eo card u ses the sh adow featu re or not.
Chapter 3 SD7- 533 Moth erboard 3-14 3-4. Advanced Chipset Features Setup Menu The Chipse t Fe atures Se tup Me nu is use d to modif y the contents of t h e b uffers in the chipse t on the mothe rboard.
Intro ducing the BIO S User’ s Manual 3-15 Advanced DRAM Contr ol 1: This item ca n le t you se t seve ral items conce rning t he DRA M p arame ters . I f y ou do not unders tand wha t each i tem do es, pl ease kee p the defau lt settings. W rong s etting s may cause syste m unsta blity , data l oss o r even prevent boot up ! Fig ure 3-5B.
Chapter 3 SD7- 533 Moth erboard 3-16 " Timin g Constr aint Cn tl: Two options are availa ble: Slow ) No rmal . The defaul t setting is Sl ow . T iming Co nstrai nt Contro l on DD R SD RAM Ba ck-to-Ba ck w rite Comma nds whic h are issue d to diffe rent r anks .
Intro ducing the BIO S User’ s Manual 3-17 AGP Fast Wri te: Tw o optio ns ar e avail able: Enable d or D isabl ed. The de fault se tting is Di sa bl ed . If your AGP adapte r can supp ort this function , then you can choose Enabled . Otherwise, c hoose Di sabl ed .
Chapter 3 SD7- 533 Moth erboard 3-18 SIS OnC hip IDE Devic e: This i tem can le t you se ts seve ral ite ms conce rning the SIS O nChip I DE device parame ters. Figure 3-6B. SIS OnC hip ID E Device S creen Shot Internal PCI / IDE: Fo ur optio ns ar e avail able: Disabl ed ) Primary ) Seconda ry ) Both.
Intro ducing the BIO S User’ s Manual 3-19 " IDE Se condary Master PIO: Six opti ons are a vailab le: Auto ) Mo de 0 ) Mo de 1 ) Mo de 2 ) Mode 3 ) Mode 4. The defaul t setti ng is Auto . T he BI OS can au to-detect the transf er m ode o f the I DE de vices in or der to set its da ta transfe r rate (D efaul t).
Chapter 3 SD7- 533 Moth erboard 3-20 Primary . Onboar d Supe r IO Devi ce: This i tem can le t you se ts seve ral ite ms conce rning the onboar d supe r I/O device par ameter s. Figure 3-6C. Onboard Super IO Device Screen Shot Onboard FDD Controll er: Tw o optio ns ar e avail able: Disabl ed or Enabl ed.
Intro ducing the BIO S User’ s Manual 3-21 " IR Transmissi on Delay: Tw o optio ns ar e avail able: Disabl ed or Enabl ed. T he de fault set ting is Enabled . Set I R transmiss ion del ays 4 charac ter- time (40 bit- time) whe n SIR is ch ange d from RX m ode to TX mode .
Chapter 3 SD7- 533 Moth erboard 3-22 " U SB K eybo ard S upp ort: Two options are av ailabl e: OS ) BI OS. The default se tting is OS . If your op eratin g system supp orts a USB ke yboard, ple ase se t it to OS .
Intro ducing the BIO S User’ s Manual 3-23 3-6. Powe r Managem ent Setup Menu The diffe rence betwee n Gree n PCs and tr aditio nal comp uters is tha t Green P Cs have a pow er manag ement fe ature. Wit h this fe atur e, whe n the com puter is powe red on b ut inactive , the po wer con sumpti on is reduc ed in ord er to save en erg y.
Chapter 3 SD7- 533 Moth erboard 3-24 ACPI Funct ion (A dvanc ed C onfig uratio n an d Pow er Inte rface ): ACPI give s the o perating system direct co ntrol ov er the powe r manag eme nt and Pl ug an d Play f unctio ns of a co mpute r. The A CP I functions are alw ays “ Enabled ”.
Intro ducing the BIO S User’ s Manual 3-25 Table 3-6- 2: Effect of Press ing th e Power Switch If the system i s in this stat e…… ……an d th e power sw itch is pressed for ……t he system e.
Chapter 3 SD7- 533 Moth erboard 3-26 Rev. 1 .0 book sect ion 9.3. 2 for more detai ls on BIOS ini tiali zation. Fro m the so ftware point of v iew , this state is fu nctionall y the sam e as the S2 s tate.
Intro ducing the BIO S User’ s Manual 3-27 PM Wake Up Events The foll owing is a list of I RQ’s ( I nterrupt R e Q uests ) and li st of th e events . When an I/O devic e want s to gain the att ention of the op eratin g system, it cau ses an I RQ or ev ent t o occu r.
Chapter 3 SD7- 533 Moth erboard 3-28 KB Power ON Pa ssword: This i tem let y ou set the passw ord f or ke ypad w akeup. A fter y ou se t the pas sword, a ny eve nt affe cting key pad will aw aken a sy stem that has pow ered do wn. Resume by Al arm: Tw o optio ns ar e avail able: Disabl ed or Enabl ed.
Intro ducing the BIO S User’ s Manual 3-29 Forc e Update ESCD: Tw o optio ns ar e avail able: Disabl ed or Enabl ed. T he de fault set ting is Disabled .
Chapter 3 SD7- 533 Moth erboard 3-30 PCI /VGA Palett e Sn oop: Tw o optio ns ar e avail able: Disabl ed or Enabl ed. T he de fault set ting is Disabled . Thi s option a llows th e BIO S to prev iew VGA Status, an d to modify the i nform ation del ivered f rom the F eature Connec tor of the VGA card to the MPEG Card.
Intro ducing the BIO S User’ s Manual 3-31 Note ! PC I sl ot 1 shares IRQ signals w i th the AG P slot. ! PC I -4 and USB contr oller s share an I RQ.
Chapter 3 SD7- 533 Moth erboard 3-32 CPU Shutdown Temperature : Five options ar e ava ilable: Disabl ed ) 60 ℃ /140 ℉ ) 65 ℃ /149 ℉ ) 70 ℃ /158 ℉ ) 75 ℃ /167 ℉ . The default se tting is Disa bl ed . You can se t the proce ssor sh utdow n tempe rature here .
Intro ducing the BIO S User’ s Manual 3-33 3-11. Set Password Set Passwor d: Can e nter but do no t have the rig h t to change the o ptions of the setup menus . Whe n you selec t thi s funct ion, th e followin g mes sage wil l app ear at the cent er of the s creen to assis t yo u in cre ating a pas swo rd.
Chapter 3 SD7- 533 Moth erboard 3-34.
SiS Chip set Driver s Installa tion for Windows ® 98 SE & Windows ® 2000 User’ s Manual A-1 Appendix A. SiS Chip set Drivers Installat ion for Windows ® 98 SE & Windows ® 2000 Af ter y ou’v e instal led Windo ws ® 98 SE or Windows ® 2000, yo u will nee d to instal l the SiS ch ipset drive rs.
Appendix A SD7- 533 Moth erboard A-2 Step 2: The SiS AGP drive r setup I nstallShie ld ® wizard s hows up , and it will go t o th e next sc reen for a while. (Windows ® 2000) Step 3: You will n ow see th e welcom e screen and it s dialogu e box. C lick “ N ext > ” to go on.
SiS Chip set Driver s Installa tion for Windows ® 98 SE & Windows ® 2000 User’ s Manual A-3 Step 6: W hen the ins tallatio n is comp lete, the inst aller will a sk you to res tart your comput er. We sugges t tha t you ch oose “ Yes, I want to restart m y com puter n ow.
Appendix A SD7- 533 Moth erboard A-4.
Installing The Winbond H ardware Monitor S ystem B-1 User’ s Manual Appendix B. Installing The Winb ond Hardware Monitor System The Winbond hard ware monitor system is a self-dia gnostic system for PCs.
B-2 Appendix B SD7- 533 Moth erboard Step 5: The welcom e screen and it s dialogu e box will appear. Clic k the “ N ext> ” butt on to go on. Step 6: Now you c an choos e the dest inat ion locatio n wher e you want to instal l the drivers . We sugges t tha t you us e the defa ult folder as the desti natio n lo cation.
Installing The Winbond H ardware Monitor S ystem B-3 User’ s Manual Step 11: You ca n sele ct the prog ram f rom Start toolb ar, and th en ch oose “ P rogr ams ”. You will see th e it em called “ winbond ” ) “ H a rd ware Doct or ”. C lick it, and you will b e able t o see th e screen belo w.
B-4 Appendix B SD7- 533 Moth erboard.
Aud io Dr ivers an d Ap plic ations Installa tion for Win dows ® 98 SE & Windows ® 2000 User’ s Manual C-1 Appendix C. Audio Dr iv ers and Applicat ions Instal latio n for Wi ndows ® 98 SE & Windows ® 2000 After you’ve in sta lled Si S chip set drivers , you will need to in sta ll the audi o dri vers.
Appendix C SD7- 533 Moth erboard C-2 Step 3: Ch oose the lan guage you wan t and click on “ OK ” butto n, it w ill go to the ne xt s cree n. (Windows ® 98 SE & Windows ® 2000 ) Step 4: You will n ow see th e Insta llSh ield ® wizard shows up.
Aud io Dr ivers an d Ap plic ations Installa tion for Win dows ® 98 SE & Windows ® 2000 User’ s Manual C-3 Step 8: Progra m will star t to insta ll driv ers that th e system n eeds. The in staller will s how th e inst all progres s percen tage.
Appendix C SD7- 533 Moth erboard C-4 Step 12: When system resta rts and enters th e operat ing system, you can go to “ System Prop erties ” then check the “ De vice Ma nager ” see th at th e devic es are p roperl y inst alled.
Aud io Dr ivers an d Ap plic ations Installa tion for Win dows ® 98 SE & Windows ® 2000 User’ s Manual C-5 We’ll in trodu ce several ap plicat ions of Audio Rack . Y ou can che ck the m her e or go to their help menu for mor e detail ed inform atio n.
Appendix C SD7- 533 Moth erboard C-6 About Bu t ton: Shows software version and copyright information . Help B utton: Show s the help s cree n for de tailed bu tton f unc tion descriptio ns. This hori zontal s lider used to ad just the b alanc e bet ween th e two spea kers.
Aud io Dr ivers an d Ap plic ations Installa tion for Win dows ® 98 SE & Windows ® 2000 User’ s Manual C-7 Speakers dialog prov ides an i nterface that all ows you to set yo ur spe aker co nfigura tion. F irst, You shoul d ma ke sur e w hat model type your speaker s are , and w h at t he cor rect co nfigura tions ar e.
Appendix C SD7- 533 Moth erboard C-8 The Options dialo g pro vides hot key se ttings to easi ly con trol t he Mixer. Pleas e note th at oth er applica tions m ay be affecte d if y ou us e the same hot key settings. Pleas e use “ Loa d Mixer Defaults ” to change all setti ngs to de fault value s.
Aud io Dr ivers an d Ap plic ations Installa tion for Win dows ® 98 SE & Windows ® 2000 User’ s Manual C-9 MIDI P layer ca n play MIDI files, * .mid / *.rm i, a nd all ow you to create your ow n playl ist. MP3/ Wave Play er can pl ay mp3, w ave, and MPEG-1 f iles .
Appendix C SD7- 533 Moth erboard C-10 Recordin g : You can use thi s function to record a wave file from an y recordin g chann el. Sett ing: T his but ton has differ ent fu nctions w hen use in dif ferent pl ayers .
Aud io Dr ivers an d Ap plic ations Installa tion for Win dows ® 98 SE & Windows ® 2000 User’ s Manual C-11 If you p ress the ri ght but ton of mouseon the demos tra tion sc reen, you will see th e advan ced dialo guge windo w. It can le t yo u set s peaker status and dem o music.
Appendix C SD7- 533 Moth erboard C-12.
BIOS Upda te Guide User’ s Manual D-1 Appendix D. BIOS Upd a te Guide We w ill use the SE6 mot herboard as an ex ample. A ll othe r mode ls follow the same process. F i rst, know your moth erboar d’s model na me and version n umber. You c an find it on one slot or at th e back of th e mothe rboar d.
Appendix D SD7- 533 Moth erboard D-2 3. Download the correct BIOS file from our Web si te. Go to our We b site a nd choos e the cor rect BI OS file and dow nload i t. 4. Do uble clic k the downlo ad file, it w ill self -extr act to . bin file. 5. Ma ke a bo otable flo ppy dis k and copy the necessar y f iles onto it.
BIOS Upda te Guide User’ s Manual D-3 Af ter fo rmatti ng and transfe rring the s ystem to the flo ppy disk, copy two file s into it. O ne is the BI OS flash utilit y “ awd flash.exe ” and the othe r is the de compress ed BIO S binar y fil e. 6.
Appendix D SD7- 533 Moth erboard D-4 Ple ase set the fir st boot s eque n ce as “ floppy ” in BI OS and bo ot off the flo ppy dis k. 7. Fl ash the BI OS in pur e DO S mo de. Af ter successf ully booting o ff of the flo ppy, e xecute the flash utility accordi ng to these instr uctions .
Trou bleshoot ing ( Nee d Assis tance?) E-1 User’ s Manual Appendix E. Troubleshoot ing (Need Assistan ce?) Motherboard Troubleshooting: Q & A: Q: Do I n eed to cle ar the C MOS b efore I us e a.
E-2 Appendix E SD7- 533 Moth erboard - Exam ple 2: With a s ystem inc luding: moth erboard (with pr ocessor, DDR DRAM, etc.) HDD, CD-R OM, FDD, grap hic ad apter, MPEG-2 ca rd, SC SI adapt er, audi o card, etc.
Trou bleshoot ing ( Nee d Assis tance?) E-3 User’ s Manual 5 * . OS/Applicati ons: Indi cate th e opera ting system and th e app licati ons you ar e runnin g on th e system. For exam ple: W indows ® 98 SE, Windows ® 2000, Window s ® XP, etc. 6 * .
E-4 Appendix E SD7- 533 Moth erboard Technical Support Form ! Com pany Name : 1 Phone Number: " Contact P erson: # Fax Number: 2 E-mail Address: Model Name * BIOS ID & P art N um ber * Mother.
How to Ge t Techn ical Su pport F-1 User’ s Manual Appendix F. How to Get Techn i cal Suppor t (From our websi te) http://www.abit.c om.tw (I n North A merica) http://www.abit-usa.co m (I n Europe) http:/ /www.abit. nl Than k yo u for choo sing A BIT pr oducts .
F-2 Appendix F SD7- 533 Moth erboard custo mer who may purchase mo re produ cts a nd who ca n urge y our frie nds to buy fro m him or he r as well. T hey integrated an d sold the sy st em to y ou. They should know best what your sy st em config uratio n is an d yo ur proble m.
How to Ge t Techn ical Su pport F-3 User’ s Manual All other territories not cove red above please contact: Taiwan Head Of fice Whe n contacting our head quarte rs pl ease note w e are lo cated in Taiwan a nd w e are 8+ G MT time. I n additio n, we hav e holiday s that may be diff ere nt from thos e in y our cou ntry .
F-4 Appendix F SD7- 533 Moth erboard.
An important point after buying a device Abit SD7-533 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Abit SD7-533 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Abit SD7-533 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Abit SD7-533 you will learn all the available features of the product, as well as information on its operation. The information that you get Abit SD7-533 will certainly help you make a decision on the purchase.
If you already are a holder of Abit SD7-533, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Abit SD7-533.
However, one of the most important roles played by the user manual is to help in solving problems with Abit SD7-533. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Abit SD7-533 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
