Instruction/ maintenance manual of the product SVM161-A Lincoln Electric
Go to page of 112
SVM161-A January , 201 1 Safety Depends on Y ou Lincoln arc welding and cutting equipment is designed and built with safety in mind. However , your overall safety can be increased by proper installation .
INVERTEC® V205-T AC/DC™ SAFETY i i FOR ENGINE powered equipment. 1.a. T urn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b.Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
SAFETY ii ii INVERTEC® V205-T AC/DC™ FUMES AND GASES can be dangerous. 5.a. Welding may produce fumes and gases hazardous to health. Avoid breathing these fumes and gases.When welding, keep your head out of the fume. Use enough ventilation and/or exhaust at the arc to keep fumes and gases away from the breathing zone.
INVERTEC® V205-T AC/DC™ SAFETY iii iii FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer ’s recommendations.
SAFETY iv iv INVERTEC® V205-T AC/DC™ PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
SAFETY Electromagnetic Compatibility (EMC) Confor mance P roducts displaying the CE mark are in conformity with European Community Council Directive of 1 5 Dec 2004 on the appro ximation of the laws of the Member Stat es relating to electromagnetic compatibilit y , 2004/1 08/EC .
SAFETY Electromagnetic Compatibility (EMC) The size of the surrounding area to be considered will depend on the structure of the building and other activities that are taking place. The surrounding area may ext end bey ond the boundar ies of the premises.
Page Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i-vi Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T ABLE OF CONTENTS - INST ALLA TION SECTION A-1 A-1 INVERTEC® V205-T AC/DC™ Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1 T echnical Specifications .
TIME-DELA Y CIRCUIT BREAKER OR FUSE SIZE (AMPS) 30A Height Width Depth Weight 15 in. 8.5 in. 19 in. Approx. 38 lbs. 381 mm 216 mm 483 mm 17 kgs. INST ALLA TION A-2 A-2 INVERTEC® V205-T AC/DC™ Input Amps 34A 28A 20A 34A 25A 20A 30A 23A 19A 30A 18A 15A T ype of Output AC/DC Output Amps V olts at Rated Amperes (Stick) 1 10 24.
INST ALLA TION A-3 A-3 INVERTEC® V205-T AC/DC™ MACHINE GROUNDING AND HIGH FRE- QUENCY INTERFERENCE PROTECTION The Capacitor Discharge Circuit used in the high fre- quency generator , may cause many radio, TV and electronic equipment interference problems.
INST ALLA TION A-4 A-4 INVERTEC® V205-T AC/DC™ 3. Be sure the torch and work cable rubber coverings are free of cuts and cracks that allow high fre- quency leakage. Cables with high natural rubber content, such as Lincoln Stable-Arc ® better resist high frequency leakage than neoprene and other synthetic rubber insulated cables.
INST ALLA TION A-5 A-5 INVERTEC® V205-T AC/DC™ In all cases, the green or green/yellow grounding wire must be connected to the grounding pin of the plug, usually identified by a green screw . Attachment plugs must comply with the Standard for Attachment Plugs and Receptacles, UL498.
INST ALLA TION A-6 A-6 INVERTEC® V205-T AC/DC™ OUTPUT AND GAS CONNECTION FOR TIG WELDING (FIGURE A.1) The TIG T orch T wist-Mate and work cable T wist-Mate Connectors are supplied with the welder . T o connect the cables, turn the Power Switch “OFF”.
INST ALLA TION A-7 A-7 INVERTEC® V205-T AC/DC™ REMOTE CONTROL CONNECTION A remote control receptacle is provided on the lower center case front of the welder for connecting a remote control to the machine. Refer to the Optional Accessories section of this manual for available remote controls.
NOTES A-8 A-8 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return t.
T ABLE OF CONTENTS - OPERA TION SECTION B-1 B-1 INVERTEC® V205-T AC/DC™ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1 Safety Instructions .
OPERA TION B-2 B-2 INVERTEC® V205-T AC/DC™ Read and understand this entire section before operating your machine. SAFETY INSTRUCTIONS ELECTRIC SHOCK can kill. • Do not touch electrically live parts such as output terminals, electrode or internal wiring.
OPERA TION B-3 B-3 INVERTEC® V205-T AC/DC™ REAR CONTROL P ANEL (FIGURE B.1) • I1: Off/On switch turns on the electric power to the welder . It has two positions, "O" off, and "I" on.
OPERA TION B-4 B-4 INVERTEC® V205-T AC/DC™ 1. Input V oltage warning light green LED - Indicates that the machine is on and input voltage is within acceptable range. 2. Thermal Shutdown Light (yellow LED) - Indicates thermal over load or output disabled for incorrect supply voltage.
OPERA TION B-5 B-5 INVERTEC® V205-T AC/DC™ 5. Output / Parameter Adjust Knob - Allows you to continuously adjust the current both in TIG and in Stick welding. Allows you to change the value, shown on "Digital Display Item 6", of the parameter selected with "Setup/Parameter select button Item 4".
OPERA TION B-6 B-6 INVERTEC® V205-T AC/DC™ 3. Press and hold the TIG torch trigger when the main part of the weld is complete. The machine will now decrease the output current at a controlled rate, or downslope time, until the Finish current is reached.
OPERA TION B-7 B-7 INVERTEC® V205-T AC/DC™ SET UP MENU Many additional parameters can be modified via the Set Up Menu. T o access the Set Up Menu: • Position the ON/OFF switch to OFF “0”. • Depress and hold the Parameter select Push Button.
OPERA TION B-8 B-8 INVERTEC® V205-T AC/DC™ WELDING POLARITY DC Electrode Negative Polarity (Direct Current Straight Polarity) (see FIGURE B.4) While Welding, there is a continuous flow of electrons from the electrode to the workpiece.
OPERA TION B-9 B-9 INVERTEC® V205-T AC/DC™ AC TIG - NOT PULSED Ip Im Ib O O t t T f = 1 to 10Hz T= 1/ f I AC - PULSED TIG DC Electrode Positive Polarity . (Direct Current Reverse Polarity) (see Figure B.5) In this case, there is a continuous flow of electrons from the workpiece to the electrode.
OPERA TION B-10 B-10 INVERTEC® V205-T AC/DC™ 1. The AC wave balance can be set to a higher per- centage electrode negative which minimizes tung- sten heating and erosion. 2. The AC frequency can be varied to "focus" the arc. Increasing the AC frequency above 60Hz will narrow the cone shape arc from the tungsten’s tip.
OPERA TION B-11 B-11 INVERTEC® V205-T AC/DC™ PROTECTIVE GAS Both argon and helium work when welding aluminum. Argon is preferred, due to its lower cost and consump- tion rate. This gas also tends to stabilize the arc, thus making it easy to operate.
OPERA TION B-12 B-12 INVERTEC® V205-T AC/DC™ DC TIG WELDING QUICK ST ART UP ELECTRIC SHOCK can kill. • Have an electrician install and service this equipment.
T ABLE OF CONTENTS - ACCESSORIES SECTION C-1 C-1 INVERTEC® V205-T AC/DC™ Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-1 Options/Accessories .
ACCESSORIES C-2 C-2 INVERTEC® V205-T AC/DC™ OPTIONAL ACCESSORIES AND COMP A TIBLE EQUIPMENT Factory Installed T wist-Mate Cable Connectors 1 – standard for Ground Clamp 1 – Gas Pass through for T ig T orch Strap Packet Instruction Manual Field Installed K857 - Remote Output Control - For Stick welding.
T ABLE OF CONTENTS - MAINTENANCE SECTION D-1 D-1 INVERTEC® V205-T AC/DC™ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D-1 Input Filter Capacitor Discharge Procedure .
MAINTENANCE D-2 D-2 INVERTEC® V205-T AC/DC™ SAFETY PRECAUTIONS ELECTRIC SHOCK can kill. • Have an electrician install and service this equipment.
MAINTENANCE D-3 D-3 INVERTEC® V205-T AC/DC™ FIGURE D.1 - MAJOR COMPONENT LOCA TIONS 1. Cradle T ube Assembly and Roof 2. Control Panel Assembly 3. Stator & Rotor Assembly and Battery 4.
NOTES D-4 D-4 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return t.
T ABLE OF CONTENTS-THEOR Y OF OPERA TION SECTION E-1 E-1 INVERTEC® V205-T AC/DC™ Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E-1 General Description .
THEOR Y OF OPERA TION E-2 E-2 INVERTEC® V205-T AC/DC™ GENERAL DESCRIPTION The Invertec® V205T AC/DC is an inverter based industrial welding power source that utilizes single- phase input power to produce constant current AC or DC output for both Stick (SMA W) and TIG (GT A W).
THEOR Y OF OPERA TION E-3 E-3 INVERTEC® V205-T AC/DC™ MAIN IGBT INVERTER BOARD The filtered input voltage, from the Input Board, is applied through an input choke to the Main IGBT Inverter Board. This input voltage is rectified, regulat- ed and a unity power factor output is developed for the main welding IGBT s.
THEOR Y OF OPERA TION E-4 E-4 INVERTEC® V205-T AC/DC™ MAIN TRANSFORMER The 100KHZ output of the Main IGBT Inverter Board is coupled, through a DC Blocking Capacitor Board, to the primary of the Main T ransformer .
THEOR Y OF OPERA TION E-5 E-5 INVERTEC® V205-T AC/DC™ CONTROL/DISPLA Y BOARD The Control/Display Board assembly is actually two boards mounted together . They should be replaced together . The Display portion houses the control panel, LEDs, push buttons and output encoders.
THEOR Y OF OPERA TION E-6 E-6 INVERTEC® V205-T AC/DC™ INSULA TED GA TE BIPOLAR TRANSIST OR (IGBT) OPERA TION An IGBT is a type of transistor . IGBT are semiconduc- tors well suited for high frequency switching and high current applications. Example A in Figure E.
T ABLE OF CONTENTS - TROUBLESHOOTING AND REP AIR F-1 F-1 INVERTEC® V205-T AC/DC™ T roubleshooting and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F-1 How to Use T roubleshooting Guide .
TROUBLESHOOTING AND REP AIR F-2 F-2 INVERTEC® V205-T AC/DC™ This T roubleshooting Guide is provided to help you locate and repair possible machine malfunctions. Simply follow the three-step procedure listed below . Step 1. LOCA TE PROBLEM (SYMPTOM).
TROUBLESHOOTING AND REP AIR F-3 F-3 INVERTEC® V205-T AC/DC™ Sometimes machine failures appear to be due to PC board failures. These problems can sometimes be traced to poor electrical connections. T o avoid prob- lems when troubleshooting and replacing PC boards, please use the following procedure: 1.
OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not und.
FUNCTION PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not u.
FUNCTION PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not u.
FUNCTION PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not u.
WELDING PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not un.
TROUBLESHOOTING AND REP AIR F-9 F-9 INVERTEC® V205-T AC/DC™ EXTERNAL DIAGNOSTICS ® P ARAMETER SELECT / HOLD PULSE ON UPSLOPE % ON TIME DOWNSLOPE FINISH CURRENT BACKGRO UND CURRENT POSTFLOW WELD CU.
TROUBLESHOOTING AND REP AIR F-10 F-10 INVERTEC® V205-T AC/DC™ INTERNAL DIAGNOSTICS L11 Under Small PCB L14 L13 Under Small PCB L12 L10 L9 L8 L4 L1 L5 L2 L3 L6 L7 FIGURE F .
TROUBLESHOOTING AND REP AIR F-11 F-11 INVERTEC® V205-T AC/DC™ INTERNAL DIAGNOSTICS (Continued) LED L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L1 1 L12 L13 L14 Definition -15VDC supply by 15.14.316 for 15.14.316 logic part +15VDC supply by 15.14.316 for 15.14.316 logic part +5VDC supply by 15.
NOTES F-12 F-12 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
ELECTRIC SHOCK can kill. • Have an electrician install and ser- vice this equipment. • Turn the input power off at the fuse box before working on equipment. • Do not touch electrically hot parts. • Prior to performing preventative maintenance, perform the following capacitor discharge proce- dure to avoid electric shock.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
INPUT FIL TER BO ARD FIGURE F .4 – INPUT FIL TER BOARD LOCA TION INPUT FIL TER BOARD TEST (continued) PROCEDURE 1. Remove input power to the V205-T . 2. Using a phillips head screwdriver , remove the case wraparound. 3. Perform the Input Filter Capacitor Discharge Procedure detailed earlier in this section.
INPUT FILTER BOARD - Checks the correct voltages as indicated on the above drawing CN 1/1-2 CN 1/3-4 V AC 2.3V (1.2V) “PE” EARTH CONNECTION POWER SUPPL Y “OUT” 230V (115V) 230V (115V) POWER SUPPL Y “IN” 230V (115V) RV1 RV2 PZ1 PZ2 FIGURE F .
NOTES F-18 F-18 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
BACK SIDE MAIN BOARD FIGURE F .6 – MAIN IGBT INVERTER BOARD LOCA TION MAIN IGBT INVERTER BOARD LOW VOL T AGE TEST (continued) PROCEDURE 1. Remove input power to the V205-T machine. 2. Using a phillips head screwdriver , remove the case wraparound cover .
MAIN IGBT INVERTER BOARD LOW VOL T AGE TEST (continued) TROUBLESHOOTING AND REP AIR F-21 F-21 INVERTEC® V205-T AC/DC™ T able F .1 T est Points ON ON ON ON ON ON ON ON TP13-TP14 TP1 1-TP14 TP12-TP14 TP3-TP5 TP4-TP5 TP17-TP18 TP21-TP18 TP2[+],TP18[-] L2 L3 L1 L4 L5 L6 L7 --- +15 VDC +5 VDC +15 VDC +24 VDC +48 VDC +15 VDC +15 VDC +14.
TP2 TP5 TP4 TP3 L4 MF2 L1 L5 L3 L2 TP14 TP13 TP12 TP11 L6 TP17 TP18 TP21 L10 L7 FIGURE F .7 – MAIN IGBT INVERTER BOARD LOCA TION This is an illustration of the upper right corner of the P .
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Control/Display Board FIGURE F .8 – CONTROL/DISPLA Y BOARD LOCA TION CONTROL/DISPLA Y BOARD TEST (continued) PROCEDURE 1. Remove input power to the V205-T machine. 2. Using a phillips head screwdriver , remove the case wraparound cover . 3. Perform the Capacitor Discharge Procedure detailed earlier in this section.
CN1 CN7 CN2 FIGURE F .9 – CONTROL/DISPLA Y BOARD LOCA TION CONTROL/DISPLA Y BOARD TEST (continued) TROUBLESHOOTING AND REP AIR F-25 F-25 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Se.
CN2 41 1 2 3 4 42 45 CN1 44 1 2 3 4 7 8 6 5 48 52 53 54 CN7 2 3 5 6 73 76 1 4 72 71 58 FIGURE F .10 – PLUGS CN1, CN2 & CN7 CONTROL/DISPLA Y BOARD TEST (continued) TROUBLESHOOTING AND REP AIR F-26 F-26 INVERTEC® V205-T AC/DC™ T able F .2 Plug CN1 T est Points T able F .
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
BUS BOARD FIGURE F .1 1 – BUS BOARD LOCA TION BUS BOARD TEST (continued) PROCEDURE 1. Remove input power to the V205-T machine. 2. Using a phillips head screwdriver , remove the case wraparound cover . 3. Perform the Capacitor Discharge Procedure detailed earlier in this section.
BUS BOARD TEST (continued) TROUBLESHOOTING AND REP AIR F-29 F-29 INVERTEC® V205-T AC/DC™ T ABLE F .5 PLUG CN2 TEST POINTS T ABLE F .6 PLUG CN3 TEST POINTS Wire # 21 22 23 24 26 27 28 29 30 32 Descr.
F1 F2 F3 CN7 CN3 CN4 CN2 CN1 FIGURE F .12 – BUS BOARD PLUG LOCA TIONS CN4 45 1 2 3 4 7 8 6 5 48 41 42 44 CN2 27 1 2 3 4 9 10 8 7 28 22 23 24 5 6 11 12 26 21 29 30 32 CN3 2 3 5 6 1 4 65 61 63 64 66 FIGURE F .
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
BACK SIDE MAIN BOARD FIGURE F .14 – LOCA TION ON MAIN BOARD T ABLE F .10 – VOL T AGE CHECKS WITH 1 15 V AC APPLIED TO MACHINE T ABLE F .1 1 – RESIST ANCE CHECKS MAIN INVERTER BOARD POWER F ACTOR SECTION TEST (continued) PROCEDURE 1. Remove input power to the V205-T machine.
TP9 GNDPWR R82 F1 TP20 MF8 RL1 PO WER INPUT 2 3 0 VA C ( 1 1 5 ) DD1 MF9 L10 G G S S S S D K K A A D FIGURE F .15 – POWER F ACTOR AREA ON MAIN BOARD NOTE: Power Factor Section is located at the uppe.
NOTES F-34 F-34 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Output Filter Board FIGURE F .16 – OUTPUT FIL TER BOARD LOCA TION OUTPUT FIL TER BOARD TEST (continued) PROCEDURE 1. Remove input power to the V205-T machine. 2. Using a phillips head screwdriver , remove the case wraparound cover . 3. Perform the Capacitor Discharge Procedure detailed earlier in this section.
- + CN1 CN1 2 3 5 6 1 4 66 53 65 54 64 FIGURE F .17 – OUTPUT FIL TER BOARD PLUG LOCA TION FIGURE F .18 – OUTPUT FIL TER BOARD PLUG CN1 T ABLE F .12 – PLUG CN1 TEST POINTS OUTPUT FIL TER BOARD TE.
NOTES F-38 F-38 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
OUTPUT TRANSIST OR OUTPUT DIODES FIGURE F .19 – SECONDAR Y POWER BOARD LOCA TION SECONDAR Y OUTPUT BOARD ASSEMBL Y TEST (continued) PROCEDURE 1. Remove input power to the V205-T machine. 2. Using a phillips head screwdriver , remove the case wraparound cover .
GA SA SB GB I I I I 10K Ohms 10K Ohms 1 2 3 A B FIGURE F .20 – SECONDAR Y POWER BOARD TEST POINT LOCA TIONS SECONDAR Y OUTPUT BOARD ASSEMBL Y TEST (continued) TROUBLESHOOTING AND REP AIR F-41 F-41 INVERTEC® V205-T AC/DC™ T ABLE F .
MODE POSITIVE METER PROBE NEGA TIVE METER PROBE EXPECTED READING MACHINE OFF TEST POINT A TEST POINT 3 LOW - LESS THAN 200 OHMS MACHINE OFF TEST POINT 3 TEST POINT A HIGH - MORE THAN 1000 OHMS MACHINE.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
BACK SIDE MAIN BOARD FIGURE F .21 – MAIN BOARD LOCA TION MAIN INVERTER BOARD “WELDING LOGIC AND INVERTER” SECTION TEST (continued) PROCEDURE 1. Remove input power to the V205-T machine. 2. Using a phillips head screwdriver , remove the case wraparound cover .
T ABLE F .15 – LED FUNCTION T ABLE F .16 – FEEDBACK VOL T AGE SIGNALS MAIN INVERTER BOARD “WELDING LOGIC AND INVERTER” SECTION TEST (continued) TROUBLESHOOTING AND REP AIR F-45 F-45 INVERTEC® V205-T AC/DC™ T ABLE F .
TP15 TP14 TP16 TP19 TP31 CN4/1-2 Shor t Cir cuit 0.3 Ohms L9 L8 CN5/1-2 Shor t Cir cuit 0.3 Ohms FIGURE F .22 – MAIN BOARD (INVERTER SECTION) MAIN INVERTER BOARD “WELDING LOGIC AND INVERTER” SEC.
L11 L14 TP9 GROUND PO WER MF11 MF15 MF16 MF12 L13 L12 D S S G SS SS S S G G G D D D FIGURE F .23 – MAIN BOARD (LOWER LEFT) MAIN INVERTER BOARD “WELDING LOGIC AND INVERTER” SECTION TEST (continue.
NOTES F-48 F-48 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
INPUT FIL TER BO ARD FIGURE F .24 – INPUT FIL TER BOARD LOCA TION S/L1 R/L1 FIGURE F .25 – INPUT FIL TER BOARD LEADS INPUT FIL TER BOARD REMOV AL AND REPLACEMENT (continued) PROCEDURE 1. Remove input power to the V205-T . 2. Using a phillips head screwdriver remove the case wraparound cover .
R V1 R V2 FIGURE F .26 – MAIN IGBT BOARD LEAD REMOV AL INPUT FIL TER BOARD REMOV AL AND REPLACEMENT (continued) Observe static precautions detailed in PC Board Troubleshooting Procedures at the beginning of this section. 7. Clean RTV off of the top of the input filter board mounting slides.
NOTES F-52 F-52 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
BACK SIDE MAIN BOARD FIGURE F .27 – MAIN IGBT BOARD LOCA TION MAIN IGBT BOARD REMOV AL AND REPLACEMENT (continued) PROCEDURE 1. Remove input power to the V205-T . 2. Using a phillips head screwdriver remove the case wraparound cover . 3. Perform the Input Filter Capacitor Discharge Procedure detailed earlier in this section.
R V1 R V2 R V4 R V3 CN1 CN2 CN3 CN4 CN5 R V6 R V7 R V5 FIGURE F .28 – MAIN BOARD PLUG AND MOUNTING SCREW LOCA TION MAIN IGBT BOARD REMOV AL AND REPLACEMENT (continued) 10. Reconnect previously removed leads RV1 thru RV7 to the P .C. board. See Wiring Diagram if necessary .
NOTES F-56 F-56 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Control/Display Board FIGURE F .29 – CONTROL/DISPLA Y BOARD LOCA TION CONTROL/DISPLA Y BOARD REMOV AL AND REPLACEMENT (continued) PROCEDURE 1. Remove the input power to the V205-T . 2. Using a phillips head screwdriver remove the four screws from the corners of the name- plate/keypad on the front of the machine.
® PARAMETER SELECT / HOLD PULSE ON UPSLOPE % ON TIME DOWNSLOPE FINISH CURRENT B ACKGRO UND CURRENT POSTFLOW WELD CURRENT sec sec sec MODE STICK DC T IG AC TIG WAR NI NG TRIGGER 4-STEP 2-STEP LOCAL REMOTE OUTPUT A PULSE FREQUENCY Hz V AC FREQUENCY Hz AC BALANCE % EN 4 Phillips Head Screws FIGURE F .
NOTES F-60 F-60 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Output Filter Board FIGURE F .32 – OUTPUT FIL TER BOARD LOCA TION OUTPUT FIL TER BOARD REMOV AL AND REPLACEMENT (continued) PROCEDURE 1. Remove input power to the V205-T . 2. Using a phillips head screwdriver , remove the case wraparound cover . 3. Perform the Input Filter Capacitor Discharge Procedure detailed earlier in this section.
Phillips Head Screws ® PARAMETER SELECT / HOLD PULSE ON UPSLOPE % ON TIME DOWNSLOPE FINISH CURRENT BACKGROUND CURRENT POSTFLOW WELD CURRENT sec sec sec MODE STICK DC TIG AC TIG WARNING TRIGGER 4-STEP 2-STEP LOCAL REMOTE OUTPUT A PULSE FREQUENCY Hz V AC FREQUENCY Hz AC BALANCE % EN Phillips Head Screws Casefront Mounting Screws FIGURE F .
- + CN1 CN2 Po s i t i v e Output Te r m i n a l Nut FIGURE F .34 – OUTPUT FIL TER BOARD OUTPUT FIL TER BOARD REMOV AL AND REPLACEMENT (continued) 18. Reconnect lead CN7 previously removed from the control/display board assembly . 19. Replace the large nut previously removed from around the positive output terminal.
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
OUTPUT DIODES FIGURE F .35 – OUTPUT DIODE LOCA TION OUTPUT DIODES REMOV AL AND REPLACEMENT (continued) TO REPLACE ANY OF THE OUTPUT DIODES (D1, D2, D3 OR D4) 1. Remove input power to the V205-T . 2. Using a phillips head screwdriver , remove the case wraparound cover .
Service and repair should be performed only by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Output T ransistor FIGURE F .36 – OUTPUT TRANSISTOR LOCA TION OUTPUT TRANSISTOR REMOV AL AND REPLACEMENT (continued) PROCEDURE 1. Remove input power to the V205-T . 2. Using a phillips head screwdriver , remove the case wraparound cover . 3. Perform the Input Filter Capacitor Discharge Procedure detailed earlier in this section.
1 2 3 Plug CN1 5mm Allen Bolts FIGURE F .37 – OUTPUT TRANSISTOR LEAD LOCA TION OUTPUT TRANSISTOR REMOV AL AND REPLACEMENT (continued) TROUBLESHOOTING AND REP AIR F-69 F-69 INVERTEC® V205-T AC/DC™.
NOTES F-70 F-70 INVERTEC® V205-T AC/DC™ Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return.
T ABLE OF CONTENTS - DIAGRAM SECTION G-1 G-1 INVERTEC® V205-T AC/DC™ T ABLE OF CONTENTS -ELECTRICAL DIAGRAMS SECTION- ELECTRICAL DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTriCaL DiaGramS G-2 iNVErTEC® V205-T aC/DC™ WiriNG DiaGram - V205-T aC/DC ST aNDarD DiaGram * *T o Ground according to National Electrical Code G-2 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
An important point after buying a device Lincoln Electric SVM161-A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lincoln Electric SVM161-A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lincoln Electric SVM161-A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lincoln Electric SVM161-A you will learn all the available features of the product, as well as information on its operation. The information that you get Lincoln Electric SVM161-A will certainly help you make a decision on the purchase.
If you already are a holder of Lincoln Electric SVM161-A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lincoln Electric SVM161-A.
However, one of the most important roles played by the user manual is to help in solving problems with Lincoln Electric SVM161-A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lincoln Electric SVM161-A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
