Instruction/ maintenance manual of the product 145 Lincoln Electric
Go to page of 34
¤ • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
¤ FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
¤ ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
¤ iii SAFETY iii FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
¤ iv SAFETY iv PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
v v Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi vi T ABLE OF CONTENTS Page Installation ................................................................................................................... ....Section A Technical Specifications .....................................................
A-1 INST ALLA TION OUTBACK™ 145 A-1 ¤ TECHNICAL SPECIFICA TIONS - OUTBACK™ 145 (K2707-1) Make/Model Description Speed (RPM) Displacement Ignition Capacities System SUBARU 1 cylinder 3750RPM High Idle 17.07 cu. in Electric & Recoil Fuel: 6.86 gal.
A-2 INST ALLA TION OUTBACK™ 145 A-2 ¤ ELECTRIC SHOCK can kill. • Do not touch electrically live parts or electrode with skin or wet cloth- ing. • Insulate yourself from work and ground. • Always wear dry insulating gloves. W ARNING ENGINE EXHAUST can kill.
A-3 INST ALLA TION OUTBACK™ 145 A-3 ¤ CAUTION SP ARK ARRESTER Some federal, state or local laws may require gaso- line engines to be equipped with exhaust spark arresters when they are operated in certain locations where unarrested sparks may present a fire hazard.
A-4 INST ALLA TION OUTBACK™ 145 A-4 ¤ ELECTRICAL OUTPUT CONNECTIONS See Figure A.1 for the location of the current control dial, weld output terminals, ground stud, circuit break- ers, 240 and 120 volt receptacles. WELDING CABLE CONNECTIONS Cable Size and Length Be sure to use welding cables that are large enough.
A-5 INST ALLA TION OUTBACK™ 145 A-5 ¤ MACHINE GROUNDING Because this portable engine driven welder or genera- tor creates its own power, it is not necessary to con- nect its frame to an earth ground, unless the machine is connected to premises wiring (your home, shop, etc.
A-6 INST ALLA TION OUTBACK™ 145 A-6 ¤ PREMISES WIRING The OUTBACK™ 145 is not recommended for premises wiring. The OUTBACK™ 145 does not have a combined 120/240 volt receptacle and cannot be connected to a premises. The OUTBACK™ 145 is intended only for backup intermittent power.
A-7 INST ALLA TION OUTBACK™ 145 A-7 ¤ CAUTION Certain Electrical devices cannot be powered by the OUTBACK™ 145. See Table A.2 TABLE A.2 ELECTRICAL DEVICE USE WITH THE OUTBACK™ 145 Type Resistiv.
B-1 OPERA TION OUTBACK™ 145 B-1 ¤ SAFETY INSTRUCTIONS Observe additional Safety Guidelines detailed throughout this manual. W ARNING W ARNING ENGINE EXHAUST can kill. • Use in open, well ventilated areas or vent exhaust outside. • Do not stack anything on or near the engine.
B-2 OPERA TION B-2 OUTBACK™ 145 ¤ GRAPHIC SYMBOLS USED ON THIS EQUIPMENT OR IN THIS MANUAL W ARNING / CAUTION CHOKE OIL FUEL AIR CLEANER CIRCUIT BREAKER GROUND (AUXILIAR Y POWER) WORK CLAMP ELECTRO.
B-3 OPERA TION B-3 OUTBACK™ 145 ¤ GENERAL DESCRIPTION The OUTBACK™ 145 is designed for commercial use welder/generator applications. As a welder it provides 145 amps of DC constant current for welding with DC stick electrodes. A single dial lets you select a full range of welding output from 50 to 145 amps.
1 2 7 8 3 or 4 6 5 B-4 OPERA TION B-4 OUTBACK™ 145 ¤ CONTROLS AND SETTINGS All welder/generator controls are located on the Output Control Panel. Gasoline engine controls are mounted on the engine. See Figure B.1 and the figures in engine operation section.
B-5 OPERA TION B-5 OUTBACK™ 145 ¤ ENGINE OPERA TION Starting/Shutdown Instructions Be sure all Pre-Operation Engine Service has been performed. Also, Read owners manual before starting for the first time. (See INSTALLATION section) NOTE: Remove all loads connected to the AC power receptacles before starting the gasoline engine.
B-6 OPERA TION B-6 OUTBACK™ 145 ¤ 4. Insert the electrode into the electrode hold er. 5. Set the current control dial to the desired output current . 6. Start the gasoline engine. See ENGINE OPERATION in this section of the manual. 7. Strike an arc and begin welding.
B-7 OPERA TION B-7 OUTBACK™ 145 ¤ TABLE B.2 ELECTRODE SELECTION GUIDE 120V Receptacle Operation: • Set the Output Control on the Pro-Cut 25 no higher than the 15 amp position.( Higher settings may cause circuit breaker on the OUTBACK™ 145 to trip.
B-8 OPERA TION B-8 OUTBACK™ 145 ¤ TABLE B.3 AUXILIARY POWER APPLICATIONS Suggested Power Applications Running Watts *Start-up Watts (Continuous) (Peak) *Air Compressor - 1 HP 2,000 4,000 - 8,000 *A.
C-1 ACCESSORIES C-1 OUTBACK™ 145 ¤ OPTIONS/ACCESSORIES The following options/accessories are available for your OUTBACK™145 from your local Lincoln Distributor: ACCESSORY KIT (K875) – Includes the following: • Twenty feet (6.1 meters) of #6 AWG electrode cable with lug.
D-1 MAINTENANCE D-1 OUTBACK™ 145 ¤ SAFETY PRECAUTIONS • Have qualified personnel do all maintenance and troubleshooting work. • Turn the engine off before working inside the machine. • Remove guards only when necessary to perform maintenance and replace them when the mainte- nance requiring their removal is complete.
D-2 MAINTENANCE D-2 OUTBACK™ 145 ¤ To service the pre-cleaner : Remove the cover. Carefully remove the foam pre- cleaner from the filter element. 1. Wash in liquid detergent and water. 2. Squeeze dry in a clean cloth. 3. Saturate in clean engine oil.
¤ E-1 TROUBLESHOOTING OUTBACK™ 145 E-1 If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TROUBLESHOOTING E-2 OUTBACK™ 145 ¤ Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-3 TROUBLESHOOTING E-3 OUTBACK™ 145 ¤ Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
F-1 DIAGRAMS F-1 OUTBACK™ 145 ¤ L13929 W IRI NG DIA G RA M - OUTBA CK 145 _ WORK 6 5 3 CB1 20A J6 9 7 + - ROTO R FIELD SLIP RINGS W2 W1 CB1 20A 6A 6B GND-F 3B 3A GND-D 3 GND-C GROUND STUD ON CONTRO.
F-2 DIMENSION PRINT F-2 OUTBACK™ 145 ¤ M21768 A.0 2 6.75 29.00 31.47 NOTES: N.A. CENTER OF GRAVIT Y W ITH OIL IN EN GINE AND EMPTY FUEL TANK. N.A. 25.
NOTES OUTBACK™ 145 ¤.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIPAMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
¤ • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
An important point after buying a device Lincoln Electric 145 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lincoln Electric 145 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lincoln Electric 145 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lincoln Electric 145 you will learn all the available features of the product, as well as information on its operation. The information that you get Lincoln Electric 145 will certainly help you make a decision on the purchase.
If you already are a holder of Lincoln Electric 145, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lincoln Electric 145.
However, one of the most important roles played by the user manual is to help in solving problems with Lincoln Electric 145. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lincoln Electric 145 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
