Instruction/ maintenance manual of the product Front Panel Board Cable Apple
Go to page of 14
07 3-1 25 7 Rev . A 1 © 2009 Apple Inc . All rights reserved. Mac P ro F irst Steps Shut down computer . 1 2 Wait 1 0 minutes. W arning: Parts inside computer can be very hot. Allow comput er to cool down bef ore continuing . Unplug all external 3 cables exc ept power cord .
07 3-1 25 7 Rev . A 2 © 2009 Apple Inc . All rights reserved. Required T ools Phillips #2 screwdriver • RIght-angle, 2.5 mm • hex driver Flatblade scr ewdriver • Long-handled Phillips • #1 sc.
07 3-1 25 7 Rev . A 3 © 2009 Apple Inc . All rights reserved. Graphics Car d 3 Locate gr aphics card in slot 1 . 4 Using Phillips #1 screwdriver , lo osen 2 captive screws securing card’ s bracket to enclosure.
07 3-1 25 7 Rev . A 4 © 2009 Apple Inc . All rights reserved. Note: Card is held in place by reten tion bar . F ollowing two steps explain how to release bar .
07 3-1 25 7 Rev . A 5 © 2009 Apple Inc . All rights reserved. 8 Holding card by top corners, pull it up out of slot. Remove card fr om 9 computer . Checklist for handling card: When removing or installing card , handle it only by the edge s. D o not touch its connectors • or any components .
07 3-1 25 7 Rev . A 6 © 2009 Apple Inc . All rights reserved. P rocessor T ray 1 0 Locate pr ocessor tray . 1 1 Pr ess down and release 2 latches on front of proce ssor tray .
07 3-1 25 7 Rev . A 7 © 2009 Apple Inc . All rights reserved. 1 2 Holding tray by latches , lift it out of computer . Place tray DIMM side 1 3 up on soft, clean cloth.
07 3-1 25 7 Rev . A 8 © 2009 Apple Inc . All rights reserved. 1 5 Remove 2 screws . Slide fan up and out 1 6 of computer . P rocessor C age 1 7 Locate pr ocessor cage.
07 3-1 25 7 Rev . A 9 © 2009 Apple Inc . All rights reserved. 1 8 Disconnect 3 cables from logic board . Using long-handled 1 9 Phillips #1 screwdriv er , loosen 6 captive screws. Rotate computer to 20 stand vertically . Using 2.5 mm hex driver , remove 5 mushr oom- head screws.
07 3-1 25 7 Rev . A 10 © 2009 Apple Inc . All rights reserved. 24 Lift cage out of enclosure. F ront P anel Board Cable 25 L ocate front panel board cable.
07 3-1 25 7 Rev . A 11 © 2009 Apple Inc . All rights reserved. 26 Disconnect cable from front panel board and backplane board. Remove cable from 27 enclosure. Installing the Replacement Cable Connect replacement 1 cable to front panel board and backplane board.
07 3-1 25 7 Rev . A 12 © 2009 Apple Inc . All rights reserved. P rocessor C age Important: Before you re- install cage into enclosure , fans must be inser ted par tway int o cage. P osition cage in 2 enclosure. Slide front and rear 3 fans into place , so that they engage with latches.
07 3-1 25 7 Rev . A 13 © 2009 Apple Inc . All rights reserved. P rocessor T ray Holding tray by 1 0 latches , lower it in to processor cage . Make sure latches are 1 1 closed ush with front of processor tra y . Graphics Car d 1 2 Reinstall graphics card in slot 1 .
07 3-1 25 7 Rev . A 14 © 2009 Apple Inc . All rights reserved. Hard Driv e 1 6 Replace hard drive in far-left drive bay . Closing the C omputer 1 Replace access panel. Note: Make sure latch is up befor e you replace panel. If latch is down, panel will not seat correctly .
An important point after buying a device Apple Front Panel Board Cable (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Apple Front Panel Board Cable yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Apple Front Panel Board Cable - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Apple Front Panel Board Cable you will learn all the available features of the product, as well as information on its operation. The information that you get Apple Front Panel Board Cable will certainly help you make a decision on the purchase.
If you already are a holder of Apple Front Panel Board Cable, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Apple Front Panel Board Cable.
However, one of the most important roles played by the user manual is to help in solving problems with Apple Front Panel Board Cable. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Apple Front Panel Board Cable along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
