
LCD TV MODELS 26LC4* 26LC5* 32LC4* 32LC5* 37LC4* 37LC5* 42LC4* 42LC5* 26LB7* 32LB7*
Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996)
ID Number(s): 4550: 26LC45 4549: 26LC46 4548: 32LC45 4547: 32LC46 4546: 37LC45 4545: 37LC46 4544: 42LC45 4543: 42LC46 4542: 32LC55 4541: 32LC56 4540: 26LC55 4539: 37LC55 4538: 42LC55 4722: 26LB75 4918: 26LB76 4723: 32LB75 4917: 32LB76 4559: 42PC55 4555: 50PC55 4554: 42PC56 4553: 50PC56 4552: 50PB65 4892: 42PC35 4891: 50PC35 4742: 60PC45



Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the product.

INPUT BRIGHT
TV/RADIO
POWER
SIMPLINK
TEXT
DVD
Slightly wipe stained spot on the exterior only with the cleansing cloths for the prod- uct exterior if there is stain or fingerprint on surface of the exterior.
VCR
Do not wipe roughly when removing stain. Please be cautious of that excessive power may cause scratch or discoloration.
SUBTITLE
SLEEP HOLD REVEAL
INDEX
TIME

(This feature is not available for all models.)
(This feature is not available for all models.)
2- TV Brackets 2- Wall Brackets 2-bolts Twister Holder Arrange the wires with the


FRONT PANEL CONTROLS

A This is a simplified representation of the front panel. Here shown may be somewhat different from your TV.
A If your product has a protection film attached, remove the film and then wipe the product with a polishing

PR

MENU
INPUT

LCD TV Models


Intelligent Eye Adjusts picture according to the sur- rounding conditions.

A This is a simplified representation of the back panel. Here shown may be somewhat different from your TV.

S-Video Input Connect S-Video out from an S-VIDEO device.
Audio/Video Input Connect audio/video output from an external device to these jacks.
PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.)
RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.
Component Input Connect a component video/audio device to these jacks.
HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable.
Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks.
RGB/DVI Audio Input Connect the monitor output from a PC to the appropriate input port.
Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
Antenna Input Connect over-the-air signals to this jack.
DIGITAL AUDIO OUT OPTICAL Connect digital audio from various types of equip- ment. Note: In standby mode, these ports do not work.


S-Video Input Connect S-Video out from an S-VIDEO device.
Audio/Video Input Connect audio/video output from an external device to these jacks.
PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.)
RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.
Component Input Connect a component video/audio device to these jacks.
HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable.
Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks.
RGB/DVI Audio Input Connect the monitor output from a PC to the appropriate input port.
Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
Antenna Input Connect over-the-air signals to this jack.
DIGITAL AUDIO OUT OPTICAL Connect digital audio from various types of equip- ment. Note: In standby mode, these ports do not work.


S-Video Input Connect S-Video out from an S- VIDEO device.
Audio/Video Input Connect audio/video output from an external device to these jacks.
PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.)
RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.
Component Input Connect a component video/audio device to these jacks.
HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable.
Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks.
RGB/DVI Audio Input Connect the monitor output from a PC to the appropriate input port.
Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
Antenna Input Connect over-the-air signals to this jack.
DIGITAL AUDIO OUT OPTICAL Connect digital audio from various types of equip- ment. Note: In standby mode, these ports do not work.


S-Video Input Connect S-Video out from an S- VIDEO device.
Audio/Video Input Connect audio/video output from an external device to these jacks.
HDMI/DVI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 3 PCMCIA CARD SLO CARD SLOT
PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.)
Component Input Connect a component video/audio device to these jacks.
HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable.
RGB/DVI Audio Input Connect the monitor output from a PC to the appropriate input port.
Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks.
DIGITAL AUDIO OUT OPTICAL Connect digital audio from various types of equip- ment. Note: In standby mode, these ports do not work.
Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
Antenna Input Connect over-the-air signals to this jack.
RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.


A



Before unfolding the stand,please make sure two locks (A)on the bottom of the stand push outward.
After unfolding the stand,please insert and tighten the screws in the holes (B)on the bottom of the stand.
This may cause the set to fall,causing serious bodily injury and serious damage to the set.

Figures shown here may be slightly different from your set.
First remove the screws in the holes (B)on the bottom of the stand.And then pull two Hooks (D)of the stand bottom and fold the stand into the back of the set.
After folding,push two Locks (A)of the stand bottom outward.

STAND INSTALLATION (Only 26, 32, 37 inch LCD TV Models)
Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage.

Assemble the product stand with the product as shown.

Install the 4 bolts securely, in the back of the product in the holes provided.

A Set it up close to the wall so the product doesn’t fall over when it is pushed backwards.
A The instructions shown below is a safer way to set up the product, which is to fix it on the wall so the
product doesn’t fall over when it is pulled in the forward direction. It will prevent the product from falling for-ward and hurting people. It will also prevent the product from damage caused by fall. Please make sure that children don’t climb on or hang from the product.
Plasma TV models LCD TV models


Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on the wall. Match the height of the bracket that is mounted on the wall.

3 Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

G When moving the product to another place undo the ropes first.
G Use a product holder or a cabinet that is big and strong enough for the size and weight of the product.
G To use the product safely make sure that the height of the bracket that is mounted on the wall is same

ATTACHING THE TV TO A DESK (Only 26/32LB7* model)
The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw.


WARNING !
G To prevent TV from falling over, the TV should be securely attached to the floor/wall per
installation instructions. Tipping, shaking, or rocking the machine may cause injury.
1-screw · Stand · Desk


Hold the CABLE MANAGEMENT with hands and push it as shown.
Connect the cables as necessary.
To connect an additional equipment, see the External equipment Setup section.



Hold the CABLE MANAGEMENT with both hands and push it as shown.
To connect an additional equipment, see the External equipment Setup section.


To connect an additional equipment, see the External equipment Setup section.
Bundle the cables using the supplied twister holder. (This feature is not available for all models.) 3
Hold the CABLE MANAGEMENT with both hands and pull it upward.
G Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken.

LCD TV model (Only 26/32LB7*)

To connect an additional equipment, see the External equipment Setup section.
Install the CABLE MANAGEMENT as shown. (Insert it as pushing the loops on the both sides of the cable management.)
Bundle the cables using the supplied twist holder. (This feature is not available for all models.)
Hold the CABLE MANAGEMENT with both hands and pull it out. (Pull it out as holding the loops on the both sides of
G Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken.



Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not pos- sible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Desktop Pedestal Installation
For proper ventilation, allow a clearance of 4" on each side and from the wall.









4 inches 4 inches 4 inches


For proper ventilation, allow a clearance of 4" on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.
If you want to install the desk-type stand fixture protection cover (50PB6* only)
To prevent the foreign materials from entering the desk-type stand fixture, fix the desk-type stand fixture protection cover by using the supplied bolts as shown at the figure.


Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
- Be careful not to bend the bronze
wire when connecting to an antenna port. - 5V antenna power works In Digital
mode only. (Refer to p. 51)


receive Digital signals from a digital set-top box or other digital external device,refer to the figure as shown below.

Connect the video outputs (Y, PB, PR) of the digital set top box to the COMPONENT IN VIDEO jacks on the set.
Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO jacks on the set.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select COMPONENT input source with using the INPUT button on the remote control.




Connect the digital set-top box to HDMI/DVI IN 1or HDMI IN 2 jack on the set.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select HDMI1 or HDMI2 input source with using the INPUT button on the remote control.


HDMI/DVI IN 1 HDMI IN 2 HDMI IN 3
OPTIC Connect the digital set-top box to HDMI/DVI IN 1, HDMI IN 2 or HDMI IN 3 jack on the set.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select HDMI1, HDMI2 or HDMI3 input source with using the INPUT button on the remote control.


Connect the digital set-top box to HDMI/DVI IN 1 jack on the set.
Connect the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the set.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select HDMI1 input source with using the INPUT button on the remote control.

HDMI/DVI IN 1 HDMI IN 2 HDMI IN 3
Connect the digital set-top box to HDMI/DVI IN 1 jack on the set.
Connect the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the set.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select HDMI1 input source with using the INPUT button on the remote control.

When connecting with a component cable

Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the set.
Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the set.
Select COMPONENT input source with using the INPUT button on the remote control.
Refer to the DVD player's manual for operating instructions.
Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below.


When connecting with a Euro Scart

Connect the Euro scart socket of the DVD to the AV1 Euro scart socket on the set.
Select AV1 input source with using the INPUT button on the remote control. If connected to AV2 Euro scart socket, select AV2 input source.
Refer to the DVD player's manual for operating instructions.
G If you want to use the EURO scart cable, you have to use

ANT OUT Connect the S-VIDEO output of the DVD to the S- VIDEO input on the set.
Connect the audio outputs of the DVD to the AUDIO input jacks on the set.
Select AV3 input source with using the INPUT button on the remote control.
Refer to the DVD player's manual for operating instruc- tions.



Connect the HDMI output of the DVD to the HDMI/DVI IN 1 or HDMI IN 2 jack on the set.
Select HDMI1or HDMI2 input source with using the INPUT button on the remote control.
Refer to the DVD player's manual for operating instructions.


JECT JECT Connect the HDMI output of the DVD to the HDMI/DVI IN 1, HDMI IN 2 or HDMI IN 3 jack on the set.
HDMI/DVI IN 1 HDMI IN 2 HDMI IN 3
Select HDMI1, HDMI2 or HDMI3 input source with using the INPUT button on the remote control.
Refer to the DVD player's manual for operating instructions.

G TV can receive the video and audio signal simultaneously
G If the DVD does not support Auto HDMI, you need to set

INSERTION OF CI MODULE
- To view the scrambled (pay) services in digital TV
mode. - This feature is not available in all countries.
HDMI IN 1 HDMI IN 1

ANTENNA IN IN
TV TV
OPTICA
Insert the CI Module to PCMCIA (Personal Computer Memory Card International Association) CARD SLOT of TV as shown.
For further information, see p.54.

the screen may remain visible on the screen.


Connect the ANT OUT socket of the VCR to the ANTENNA IN socket on the set.
Connect the antenna cable to the ANT IN socket of the VCR.
Press the PLAY button on the VCR and match the appropriate programme between the TV and VCR for viewing.

When connecting with a Euro Scart
AV 1 AV 2
AUDIO IN (RGB/DVI) B (PC)
Connect the Euro scart socket of the VCR to the AV1 Euro scart socket on the set.
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
Select AV1 input source with using the INPUT button on the remote control.
If connected to AV2 Euro scart socket, select AV2 input source.
NOTE !
G If you want to use the EURO scart cable, you have to use the signal shielded Euro scart cable.
Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colours (Video = yellow, Audio Left = white, and Audio Right = red)
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
Select AV3 input source using the INPUT button on the remote control.
ANT IN
NOTE !
OUTPUT SWITCH
ANT OUT
G If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO jack of the set.


Connect the S-VIDEO output of the VCR to the S- VIDEO input on the set. The picture quality is improved; compared to normal composite (RCA cable) input.
Connect the audio outputs of the VCR to the AUDIO input jacks on the set.
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
Select AV3 input source with using the INPUT button on the remote control.
G If both S-VIDEO and VIDEO sockets have been connected to
the S-VHS VCR simultaneously, only the S-VIDEO can be received.
Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical) port.


Connect one end of an optical cable to the TV Digital Audio (Optical) Output port.
Connect the other end of the optical cable to the digi- tal audio (optical) input on the audio equipment.
Set the “TV Speaker option - Off” in the AUDIO menu. (Gp.85). See the external audio equipment instruction manual for operation.

GDo not look into the optical output port. Looking at the

OTHER A/V SOURCE SETUP

Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red)
Select AV3 input source with using the INPUT button on the remote control.
Operate the corresponding external equipment. Refer to external equipment operating guide.

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

Connect the RGB output of the PC to the RGB (PC) jack on the set.
Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the set.
Select RGB input source with using the INPUT but- ton on the remote control.

Connect the DVI output of the PC to the HDMI/DVI IN 1 jack on the set.
Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the set.
Select HDMI1 input source with using the INPUT button on the remote control.
G If the PC has a DVI output and no HDMI output, a separated audio connection is necessary.
G If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the best
picture quality, adjust the output resolution of PC graphics card's output resolution to 1024x768, 60Hz.

G To enjoy vivid picture and sound, connect a PC to
G Connect the audio cable from the PC to the Audio
the set.
input on the set. (Audio cables are not included with the set).
G Avoid keeping a fixed image on the set’s screen for
a long period of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible.
G If using a sound card, adjust PC sound as required.
G This set uses a VESA Plug and Play Solution. The
set provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically when using this set.
G Connect PC to the RGB (PC) or HDMI IN (or
HDMI/DVI IN) port of the set; change the resolu- tion output of PC accordingly.
G DDC protocol is preset for RGB (Analog RGB),
G There might be noise according to some resolution,
HDMI (Digital RGB) mode.
vertical pattern, contrast or brightness in PC mode. Change the PC mode into another resolution or change the refresh rate into another rate or adjust the brightness and contrast on the menu until the picture is clean. If the refresh rate of the PC graph- ic card can not be changed, change the PC graph- ic card or consult it to the manufacturer of the PC graphic card.
G If required, adjust the settings for Plug and Play
functionally.
G If graphic card on the PC does not output analog
and digital RGB simultaneously, connect only one of either RGB or HDMI IN (or HDMI/DVI IN) to display the PC on the set.
G If graphic card on the PC does output analog and
digital RGB simultaneously, set the set to either RGB or HDMI; (the other mode is set to Plug and Play automatically by the set.)
G The synchronization input waveform for Horizontal
and Vertical frequencies are separate.
G In Plasma TV models, we recommend using
G DOS mode may not work depending on video card
1024x768, 60Hz for the PC mode, they provide the best picture quality.
if you use a HDMI to DVI cable.
G When you use too long RGB-PC cable, there might
G Connect the signal cable from the monitor output
be a noise on the screen. We recommend using under 5m of the cable. It provides the best picture quality.
port of the PC to the RGB (PC/DTV) port of the set or the signal cable from the HDMI output port of the PC to the HDMI IN (or HDMI/DVI IN) port on the set.

Except 26/32LB7*
RGB[PC] / HDMI[PC] mode
31.468 31.469 37.684 37.879 46.875 49.725 48.363 56.476 60.123 47.78 47.72 47.56 66.647
70.08 59.94 75.00 60.31 75.00 74.55 60.00 70.00 75.029 59.87 59.8 59.6 59.988
31.469 31.469 31.47 31.50 31.25 37.50 44.96 45.00 33.72 33.75 28.125 27.00 56.25 67.433 67.500
59.94 60.00 59.94 60.00 50.00 50.00 59.94 60.00 59.94 60.00 50.00 24.00 50.00 59.94 60.00
Only 26/32LB7*
RGB[PC] / HDMI[PC] mode
31.468 31.469 37.500 37.879 46.875 49.725 48.363 56.476 60.023 47.649 47.649 47.649 66.647
70.08 59.94 75.00 60.31 75.00 74.55 60.00 70.00 75.023 59.99 59.94 59.94 59.988
31.469 31.469 31.47 31.50 31.25 37.50 44.96 45.00 28.125 33.72 33.75 27.000 56.250 67.433 67.500
59.94 60.00 59.94 60.00 50.00 50.00 59.94 60.00 50.00 59.94 60.00 24.00 50.00 59.94 60.00


Screen Setup for PC mode
Auto Configure (RGB [PC] mode only)
Automatically adjusts picture position and minimizes image shaking.After adjustment, if the image is still not correct, your set is functioning properly but needs further adjust- ment.
This function is for the automatic adjustment of the screen position, clock, and phase. The displayed image will unstable for a few seconds while the auto configuration is in progress.

Auto Config. Manual Config. XGA Mode Aspect Ratio Reset
Press the MENU button and then use D or E button to select the SCREEN menu.
Press the G button and then use D or E button to select Auto Config..
Press the G button to start Auto Config..

Auto Config. G Manual Config. XGA Mode Aspect Ratio Reset
Auto configure


If the picture isn’t clear after auto adjustment and espe- cially if characters are still trembling, adjust the picture phase manually.
To correct the screen size, adjust Clock.
This function works in the following mode : RGB[PC].
Clock This function is to minimize any vertical bars or
Auto Config. Manual Config. XGA Mode Aspect Ratio Reset
stripes visible on the screen background. And the horizontal screen size will also change.
Phase This function allows you to remove any horizontal
noise and clear or sharpen the image of characters.

Auto Config. Manual Config. G XGA Mode Aspect Ratio Reset

Press the MENU button and then use D or E button to select the SCREEN menu.
Press the G button and then D or E button to select Manual Config..
Press the G button and then D or E button to select Phase, Clock, H-Position or V-Position.
Press the F or G button to make appropriate adjust- ments.


Selecting Wide XGA mode
To see a normal picture, match the resolution of RGB mode and selection of XGA mode.
This function works in the following mode: RGB[PC] mode
Auto Config. Manual Config. XGA Mode Aspect Ratio Reset

Press the MENU button and then use D or E button to select the SCREEN menu.
Press the G button and then use D or E button to select XGA Mode.
Press the G button and then use D or E button to select the desired XGA resolution.

Auto Config. Manual Config. XGA Mode G Aspect Ratio Reset


This function operates in current mode. To initialize the adjusted value
It’s not available to use ISM Method and Low power in LCD TV models.
Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode

Press the MENU button and then D or E button to select the OPTION menu.
Press the G button and then D or E button to select Factory Mode.
Press the G button and then D or E button to select Factory Reset.

Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode G
The message “If you enter a password, all user setting will be reset” will appear.

Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode

REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.

Switches the set on from standby or off to standby.
Selects digital or analogue mode. Switches the set on from standby.
External input mode rotate in regular sequence. Switches the set on from standby.
Adjusts screen brightness. It returns to the default settings brightness by changing mode source.
These buttons are used for teletext (only TELETEXT models) or Programme edit.
Clears all on-screen displays and returns to TV viewing from any menu.
Allow the user to move back one step in an interactive application, EPG or other user interaction function.
Selects a programme. Selects numbered items in a menu.

MODE Selects the remote operating modes.
TV D/A
POWER
See a list of AV devices connected to TV. When you toggle this button, the Simplink menu appears at the screen. (G p.62)
DVD
INPUT BRIGHT
VCR
TELETEXT BUTTONS
These buttons are used for teletext. For further details, see the ‘Teletext’ section.
TEXT
RATIO I/II
Selects your desired picture format.
Selects the sound output.
Controls some video cassette recorders or DVD players when you have already selected DVD or VCR mode button. Control connected AV devices by pressing the D or E or F or G, OK buttons and buttons for play, stop, pause, fast reverse, fast forward, chapter skip. (The button does not provide such functions.)
Allows you to navigate the on-screen menus and adjust the system settings to your preference.
Accepts your selection or displays the current mode.
Sets the sleep timer.
Recalls your preferred subtitle in digital mode.
INDEX
TIME
SLEEP HOLD REVEAL
the batteries matching correct polarity (+with +,-with -).
new ones.

REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
Switches the set on from standby or off to standby.
TV INPUT D/A
D/A INPUT
Selects digital or analogue mode. Switches the set on from standby.
I/II MUTE TEXT
INPUT
External input mode rotate in regular sequence. Switches the set on from standby.
Selects Radio or TV channel in digital mode.
Selects the sound output.
Switches the sound on or off.
0~9 number button
Selects a programme. Selects numbered items in a menu.
Displays the programme table.
Returns to the previously viewed programme.
Selects a menu.
Clears all on-screen displays and returns to TV viewing from any menu.
Shows the present screen information.
Shows programme schedule.
SUBTITLE UPDATE
THUMBSTICK
Allows you to navigate the on-screen menus and adjust the system settings to your preference.
TIME
HOLD REVEAL
Accepts your selection or displays the current mode.
Adjusts the volume.
Allow the user to move back one step in an interactive application, EPG or other user interaction function.
Displays the selected favourite programme.
Selects a programme.


These buttons are used for teletext. For further details, see the ‘Teletext’ section.
These buttons are used for teletext (only TELETEXT models) or Programme edit.

TURNING ON THE TV
- If your TV will be turned on, you will be able to use its features.


First, connect power cord correctly. At this moment, the TV switches to standby mode.
In standby mode to turn TV on, press the r / I, INPUT or PR D or E button on the TV or press the POWER, INPUT, D/A, PR + or - or NUMBER button on the remote control and then the TV will switch on.
If the OSD (On Screen Display) is displayed on the screen as figure after turning on the set, you can adjust the Language, Country, Time Zone, Auto programme tuning.
unless a button is pressed. b. Press the BACK button to change current OSD into



Press the PR + or - or NUMBER buttons to select a pro- gramme number. 1
VOLUME ADJUSTMENT

Press the VOL + or - button to adjust the volume.
If you want to switch the sound off, press the MUTE button.
You can cancel this function by pressing the MUTE, VOL + or -, or I/II button.

ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.

Press the MENU button and then D or E button to display each menu.
Press the G button and then D or E button to select a menu item.
Change the setting of an item in the sub or pull-down menu with F or G button. You can move to the higher level menu by pressing the OK or MENU button.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
* : This feature is not available in all countries.
Auto Config. Manual Config. XGA Mode Aspect Ratio Reset
Sound Mode Auto Volume Balance 0 TV Speaker Digital Audio Out
Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode Index
Clock Off Time On Time Auto Sleep Time Zone
* : This feature is not available in all countries.
G It’s not available to use ISM Method and Low power in LCD TV models.
G In Analogue mode, 5V Antenna Power, CI Information, Software Update and Diagnostics
G It’s available to use Index in 50PB6*.


Use it to automatically find and store all of the programmes.
When you start auto programming in digital mode, all the stored service information will be deleted.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select Auto Tuning.
Press the G button to begin auto tuning. Use NUMBER buttons to input a 4-digit password in Lock System ‘On’.

Auto Tuning G Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
The message “All service-information will be updated. Continue?” will appear.
If you want to keep on auto tuning select YES with using the F or G button. Then, press the OK button. Otherwise select NO.


MANUAL PROGRAMME TUNING (IN DIGITAL MODE)
Manual Tuning lets you manually add a programme to your programme list.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select Manual Tuning.
Press the G button and then D or E button or NUM- BER buttons to select the desired channel number. Use NUMBER buttons to input a 4-digit password in Lock System ‘On’.

Auto Tuning Manual Tuning G Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
Your receiver will add this channel to your channel list.
When the channel number you want to add is already added in programme list, the massage “Setup infor- mation for the channel will be updated. Continue?” will appear.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
Your receiver will add this channel to your channel list.
If you want to keep on manual tuning, select YES with using the F or G button.
Then, press the OK button. Otherwise select NO.


When a programme number is skipped, it means that you will be unable to select it using PR + or - button during TV viewing.
If you want to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the Programme edit menu.
This function enables you to skip the stored programmes.
It’s available in some countries only to move a programme num- ber by YELLOW button.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select Programme Edit menu.
Press the G button to enter the Programme Edit menu. Use NUMBER buttons to input a 4-digit password in Lock System ‘On’.

Auto Tuning Manual Tuning Programme Edit G 5V Antenna Power Software Update Diagnostics CI Information
Select a programme to be stored or skipped with the
Press the BLUE button repeatedly to have the pro- gramme skipped or stored.
In case of programmes to be skipped, skipped pro- gramme shows in blue colour and these programmes will not be selected by the PR + or - buttons during TV viewing.

Displayed when the DTV Programme.
Displayed when the Teletext Programme.
Displayed when the Locked Programme.
Displayed when the Subtitle Programme.
Displayed when the Radio Programme.
Displayed when the Scramble Programme.
Displayed when the MHEG Programme.
Displayed when the Dolby Programme.
A Skipping a programme number
Select a programme number to be skipped with the D or E or F or G button.
Press the BLUE button. The skipped programme number turns to blue.
Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be unable to select it using the PR + or - but- ton during normal TV viewing.
If you want to select the skipped programme, directly enter the programme number with the NUMBER but- tons or select it in the programme edit or EPG.
Press the EXIT button to return to TV viewing.
A Locking a programme (In Lock System On mode only)
Select a programme to be locked with the D or E or F or G button.
Press the GREEN button. The lock mark will appear in front of that programme number.
Press the GREEN button again to release this function.
G To watch a locked programme, input a 4-digit password in Lock system. Be sure to remember this number!
G If you forgot your password, press ‘7’, ‘7’, ‘7’, ‘7’ on the remote control handset.
G If you select other programme after releasing a locked programme and then return to the locked programme
within 1 minute, you needn’t input a password to select the locked programme.
A Selecting favourite programme
Select your favourite programme number by pressing D or E or F or G button and then press the FAV but- ton on your remote control handset.
It will automatically include the selected programme into your favourite programme list.
Mini Glossary


Even if there isn’t a special 5V adapter power in the external antenna, this function can output 5V in the set.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then use D or E button to select 5V Antenna Power.
Press the G button and then use D or E button to select On or Off.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power G Software Update Diagnostics CI Information
In 5V Antenna Power On, if the set is short-cir- cuit, it will automatically return to Off.
The message “Antenna feed overloaded. Automatically switched off.” will appear.


SOFTWARE UPDATE (IN DIGITAL MODE ONLY)
Software Update means software can be downloaded through the digital terrestrial broadcasting system.

Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select Software update.
Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
Press the G button and then D or E button to select Off or On.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update G Diagnostics CI Information

Occasionally, a transmis- sion of updated digital software information will result in the following menu on the TV screen.

Select the YES using the
F or G button and when you see the following picture.
After Software Update is completed, the System takes about one minute to restart.


This function enables you to watch Manufacturer, Model/Type, Serial Number and Software Version.
It’s displayed the information and signal strength of the tuned MUX. It’s displayed the signal information and service name of the selected MUX.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then use D or E button to select Diagnostics.
Press the G button to display Manufacturer, Model/Type, Serial Number and Software Version.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics G CI Information
Manufacturer : LG Electronics Inc. Model / Type : 37LC2D-EC Serial No. : 604KG0000006 Software Version : 1.1.0
1 YLE PEU 1 YLE TV1 3 YLE TV2 4 YLEQ 5 YLE FST 6 YLEN KLASS 7 YLE FSR+ 8 YLE24
Menu Prev.

![LG Electronics 42PC3 — CI [COMMON INTERFACE] INFORMATION(IN DIGITAL MODE ONLY) diagram (page 56)](/cdn/reader/68/684e4dc97836ad7ebf87d92ffcf5063a68b8eb32002b6d6e583a32dc8cb9b031/images/fig-56-1.webp)
CI [COMMON INTERFACE] INFORMATION (IN DIGITAL MODE ONLY)
This function enables you to watch some scrambled services (pay ser- vices). If you remove the CI Module, you can’t watch the pay services. When the module is inserted to CI slot, you can access the module menu. To purchase a module and smart card, contact your supplying dealer. Do not often insert or remove a CAM module from the set. It may cause a trouble. When the set turned on after inserting the CI Module, you often can’t hear the sound.
There might be unnatural picture according to CI module and smart card.
CI (Common Interface) function may not be applied based on country broadcasting circumstance.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select CI Information.
Press the D or E button to select the desired item: Module information, smart card information, lan- guage, or software download etc.

Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information G Module



All stations that can be received are stored by this method. It is recommended that you use Auto tuning during installa- tion of this set.
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select Auto Tuning.
Press the G button to select System. Select a TV system with the F or G button;
Asia / New Zealand / M.East / Africa / Australia) I : PAL I/II (U.K. / Ireland / Hong Kong / South
Press the E button to select Storage From.
Select the beginning programme number with the F or G button or NUMBER buttons on the Storage From menu.

Press the E button to select Start.
The station name is stored for stations which broad- cast VPS (Video Programme Service), PDC (Programme Delivery Control) or TELETEXT data.
If no station name can be assigned to a station, the channel number is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47), followed by a number.
To stop auto tuning, press the MENU button.
When auto tuning is completed, the Programme Edit menu appears on the screen.
See the ‘Programme Edit’ section to edit the stored programme.
Africa / CIS)


Manual Tuning lets you manually tune and arrange the sta- tions in whatever order you desire.
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select Manual Tuning.
Press the G button to select Storage.
Select the desired programme number with the F or G button or NUMBER buttons on the Storage menu.
Press the E button to select System. Select a TV system with the F or G button;
Asia / New Zealand / M.East / Africa / Australia) I : PAL I/II (U.K. / Ireland / Hong Kong / South

Press the E button to select Band. Press the F or G button to select V/UHF or Cable as required.
Press the E button to select Channel. You can select the desired channel number with the F or G button or NUMBER buttons.
If possible, select the channel number directly with the NUMBER buttons.
Press the E button to select Search. Press the F or G button to commence searching. If a station is found the search will stop.
Press the OK button to store it.
To store another station, repeat steps 3 to 8.
Africa / CIS)


Normally fine tuning is only necessary if reception is poor.
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select Manual Tuning.
Press the G button and then D or E button to select Fine.
Press the G button and then F or G button to fine tune for the best picture and sound.
Press the OK button to store it.

You can assign a station name with five characters to each programme number.
Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select Manual Tuning.

Press the G button and then D or E button to select Name.
Press the G button and then D or E button. You can use a the alphabet A to Z, the number 0 to 9, +/ -, and blank.
Press the F or G button to select the position and make your choice of the second character, and so on.
Press the OK button to store it.


PROGRAMME EDIT (IN ANALOGUE MODE)
This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or copy a blank station data into the selected programme number.

Press the MENU button and then D or E button to select the SETUP menu.
Press the G button and then D or E button to select Programme Edit.
Press the G button to display the Programme Edit menu.
Select a programme to be deleted with the D or E or
Auto Tuning Manual Tuning Programme Edit G To Set
Press the RED button twice. The selected programme is deleted, all the following programmes are shifted up one position.
Select a programme to be copied with the D or E or
Press the GREEN button. All the following programmes are shifted down one position.

SLEEP
SUBTITLE UPDATE
EXIT GUIDE
INDEX
TIME
HOLD REVEAL
0 LIST
Q.VIEW
INDEX POSITION TIME
A Moving a programme
a
Select a programme to be moved with D or E or F or G button.
Press the YELLOW button.
Move the programme to the desired programme number with the D or E or F or G button.
Press the YELLOW button again to release this function.
A Skipping a programme number
Select a programme number to be skipped with D or E or F or G button.
Press the BLUE button. The skipped programme number turns to blue.
Press the BLUE button to release the skipped programme.
When a programme number is skipped it means that you will be unable to select it using the PR + or - button during normal TV viewing.
If you want to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or table menu.
A Selecting Favourite Programme
Select your favourite programme number with D or E or F or G button.
Press the FAV button.
The selected programme will be added to the favourite programme list.
* · ?


CALLING THE PROGRAMME TABLE
You can check the programmes stored in the memory by displaying the programme table.

Press the LIST button to display the PROGRAMME LIST menu.
< In Digital Mode >
Select a programme with the D or E button.
Press the OK button. The set switches to the chosen pro- gramme number.
6 S 04
7 S 05
There are programme LIST pages which total contain 100 programmes. (Analogue Mode)
9 S 12
Press the PR + or - button repeatedly to turns the pages.
< In Analogue Mode >
Press the LIST button to return to normal TV viewing.
Displayed when the Favourite Programme. Displayed when the Locked Programme.
Press the FAV button to display the Favourite Programme table menu.
Programme List · Mini Glossary


FUNCTION (except 42/50PC3*)
This operates only for the devices with the SIMPLINK logo. Please check the SIMPLINK logo.
This allows you to control and play other AV devices connected to the display through HDMI cable without additional cables and settings.
If you do not want SIMPLINK menu, select “Off”.
In 26/32LB7* model, SIMPLINK function is not supported by HDMI IN 3 input.
Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode

Press the MENU button and then D or E button to select the OPTION menu.

Language Country Lock System Parental Control Input Label SIMPLINK G Factory Mode
Press the G button and then D or E button to select SIMPLINK.
Press the G button and then D or E button to select Off or On.

Disc playback Control connected AV devices by pressing the D or E or F or G, OK, and buttons.
Direct Play After connecting AV devices to TV, you can directly control the devices and play media without additional settings.
Select AV device Enables you to select one of AV devices connected to TV and play it.
Power off all devices When you power off TV, all connected devices are turned off.
Switch audio-out Offers an easy way to switch audio-out.
* A device, which is connected to TV through HDMI cable but does not support Simplink, does not provide this function.
Press the D or E or F or G button and then OK button to select the desired SIMPLINK source.
TV viewing : Switch to the previous TV programme regardless of the current mode.

DISC playback : Select and play connected discs. When multiple discs are available, the titles of discs are conveniently displayed at the bottom of the screen.
When no device is connect- ed (displayed in gray)
VCR playback : Play and control the connected VCR.
HDD Recordings playback : Play and control recordings stored in HDD.
When a device is connected (displayed in bright colour)
Audio Out to Home theatre/Audio Out to TV: Select Home theatre or TV speaker for Audio Out.
G Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the
SIMPLINK device with the HDMI cable.
G After connecting the HDMI terminal for the home theater with SIMPLINK function in the above method,
connect the DIGITAL AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIMPLINK device with the OPTICAL cable.
G When operating the external device with SIMPLINK, press the TV button among the MODE button on the
remote controller.
G When you switch the Input source with the INPUT button on the remote controller, you can stop the
operation of device controlled by SIMPLINK.
G When you select or operate the media device with home theater function, the speaker automatically
switches to home theater speaker (HT speaker).
Selected Device

EPG (ELECTRONIC PROGRAMME GUIDE) (IN DIGITAL MODE)
This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible viewing options.
The EPG supplies information such as programme listings, start and end times for all available services. In addition, detailed information about the programme is often available in the EPG (the availability and amount of these programme details will vary, depending on the particular broadcaster).
This function can be used only when the EPG information is broadcasted by broadcasting companies.
The EPG displays the programme description for next 8 days.
Switch on/off EPG
Press the GUIDE button to switch on EPG.
Press the GUIDE or EXIT button again to switch off EPG and return to normal TV viewing.

Press the D or E, F or G, PR + or - button to select desired programme, then press the OK button to display the selected programme.

Remote Control Buttons Function

RED Change EPG mode YELLOW Enter Timer Record/Remind setting mode BLUE Enter Timer Record/Remind list mode Change to the selected channel
F or G Select NOW or NEXT Programme
D or E Select the Broadcasting Programme PR + or - Page Up/Down GUIDE/EXIT Switch off EPG TV/RADIO Select TV or RADIO Programme INFO i The detail information on or off
Remote Control Buttons Function
RED Change EPG mode GREEN Enter Date setting mode YELLOW Enter Timer Record/Remind setting mode BLUE Enter Timer Record/Remind list mode Change to the selected channel
F or G Select NOW or NEXT Programme
D or E Select the Broadcasting Programme PR + or - Page Up/Down GUIDE/EXIT Switch off EPG TV/RADIO Select TV or RADIO Programme INFO i The detail information on or off
Remote Control Buttons Function

GREEN Switch off Date setting mode Change to the selected date
F or G Select a date
E Switch off Date setting mode GUIDE/EXIT Switch off EPG

Button Function in Extended Description Box

Remote Control Buttons Function
D or E Text Up/Down YELLOW Enter Timer Record/Remind setting mode INFO i The detail information on or off GUIDE/EXIT Switch off EPG
- This function is available only when recording equipment that use pin8 recording signalling has
been connected to the DTV-OUT terminal, using a SCART cable.
Remote Control Buttons Function

YELLOW Change to Guide or Timer list mode Save Timer Record/Remind
F or G Select Type, Service, Date or Start/End time
D or E Function setting

Remote Control Buttons Function
YELLOW Add new Manual Timer setting mode GREEN Enter Timer list editing mode RED Delete the selected item BLUE Change to Guide mode
D or E Select Timer list

You can watch the screen in various picture formats; Spectacle (except 26/32LB7*, 42/50PC3*, 60PC4*), Full, Original, 4:3, 16:9, 14:9 and Zoom1/2.
If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible.
There might be uncomfortable in full mode. Then change into other mode.
You can adjust the enlarge proportion using D or E button.
This function works in the following signal.
Press the RATIO button repeatedly to select the desired picture format. You can also adjust Aspect Ratio in the SCREEN menu. 1
When your TV receives the wide screen signal, when selected it will adjust the picture horizontally, in non-lin- ear proportion, to fill the entire screen.



4:3


16:9

NOTE !
G You can only select 4:3, 16:9 (Wide), Zoom 1/2 in Component, HDMI mode.
G You can only select 4:3, 16:9 (Wide) in RGB mode only.
Zoom1 DE · Zoom2 DE


Picture Mode-Preset
Dynamic Select this option to display with a sharp image. Standard The most general and natural screen display sta- tus. Mild Select this option to display with a mild image. User 1/2 Select this option to use the user-defined set- ting.

Press the MENU button and then D or E button to select the PICTURE menu.
Press the G button and then D or E button to select Picture Mode.
Press the G button and then D or E button to select Intelligent Eye (only 26/32LB7*), Dynamic, Standard, Mild, User 1, or User 2.

Picture Mode adjusts the set for the best picture appearance. Select the preset value in the Picture Mode menu based on the programme category.
Dynamic, Standard and Mild are programmed for optimum picture reproduction at the factory and can- not be changed.


Auto Colour Tone Control (Warm/Medium/Cool)
To initialize values (reset to default settings), select the Cool option.
Choose one of three automatic colour adjustments. Set to warm to enhance hotter colours such as red, or set to cool to see less intense colours with more blue.
It’s available to use this function in User mode.

Press the MENU button and then D or E button to select the PICTURE menu.
Press the G button and then D or E button to select Colour Temperature.

Press the G button and then D or E button to select either Cool, Medium, Warm, or User.

Picture Mode-User option
Contrast Adjusts the difference between the light and dark levels in the picture. Brightness Increases or decreases amount of white in the your picture. Colour Adjusts intensity of all colours. Sharpness Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower the level, the softer the image. Tint Adjusts the balance between red and green lev- els.
Picture Mode Colour Temperature
Press the MENU button and then D or E button to select the PICTURE menu.
Press the G button and then D or E button to select Picture Mode.
Picture Mode G Colour Temperature
Dynamic Standard Mild User 1 User 2
Press the G button and then D or E button to select User 1 or User 2.
Press the G button and then D or E button to select the desired picture option (Contrast, Brightness, Colour, Sharpness and Tint).
Contrast 100 G Brightness 45 Colour 50 Sharpness 50 Tint 0
Press the F or G button to make appropriate adjustments.
NOTE !
G You can’t adjust colour, sharpness and tint in the RGB-
PC mode to the levels you prefer.


To adjust red, green, blue to any colour temperature you prefer.
Press the MENU button and then D or E button to select the PICTURE menu.
Press the G button and then D or E button to select Colour Temperature.
Press the G button and then D or E button to select User.
Press the G button and then D or E button to select Red, Green or Blue.
Press the F or G button to make appropriate adjustments.

XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital signal pro- cessing algorithm.
It’s not available to use this function in RGB-PC mode.

Press the MENU button and then D or E button to select the PICTURE menu.
Press the G button and then D or E button to select XD.
Press the G button and then D or E button to select Auto or Manual.
Picture Mode Colour Temperature
* Selecting the Manual
This menu is activated after selecting the User1 or User2 of Picture Mode.
Press the G button and then D or E button to select XD Contrast, XD Colour, XD NR or MPEG NR.
Picture Mode Colour Temperature
G Advanced Picture Reset
Press the G button and then D or E button to select On or Off.
MPEG NR 0
according to the brightness of the reflection.
Picture Mode Colour Temperature
automatically to reproduce as closely as possible to the natural colors.
does not damage the original picture.
appear on the screen during watching the TV.


Use it to see the difference between XD Demo on and XD Demo off.
It’s not available to use this function in RGB[PC], HDMI[PC] mode.
Press the MENU button and then D or E button to select the PICTURE menu.
Press the MENU button and then D or E button to select XD Demo.
Press the G button to begin XD Demo.
To stop XD Demo, press the MENU or EXIT button.



Set up the TV for the best picture appearance for viewing movies.
This feature operates only in DTV, AV, S-Video and Component 480i/576i mode.
Press the MENU button and then D or E button to select
Press the G button and then D or E button to select Advanced.
Press the G button and then D or E button to select Cinema.
Press the F or G button to select On or Off.



When you watch the movie, this function adjusts the set to the best picture appearance. Adjusting the contrast and the bright- ness of the screen using the black level of the screen.
This function works in the following mode: AV (NTSC-M), S- Video (NTSC-M) or HDMI.
Press the MENU button and then D or E button to select the PICTURE menu.
Press the G button and then D or E button to select Advanced.
Press the G button and then D or E button to select Black Level.
Press the F or G button to select Low or High.
A Low : The reflection of the screen gets darker.
A High : The reflection of the screen gets brighter.


Returns to the default settings Picture Mode, Colour Temperature, XD, Advanced at the factory.
Press the MENU button and then D or E button to select the PICTURE menu.
Press the G button and then D or E button to select Picture Reset.
Press the G button to initialize the adjusted value.


IMAGE STICKING MINIMIZATION (ISM) METHOD
A frozen of still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the set's screen for a long period of time.
It’s not available to use this function in LCD models.
White wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash.
Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode
Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the screen will move every 2 minutes.

Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode G
This is the function to invert the panel colour of the screen. The panel colour is automatically inverted every 30 minutes.

Press the MENU button and then D or E button to select the OPTION menu.
Press the G button and then D or E button to select Factory Mode.

Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode
Press the G button and then D or E button to select ISM Method.
Press the F or G button to select either Normal, White wash, Orbiter or Inversion. If you unnecessary to set this function, set Normal.
White wash · Orbiter · Inversion


This is the function to reduce the power consumption of the set.
It’s not available to use this function in LCD TV models.

Press the MENU button and then D or E button to select the OPTION menu.
Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode
Press the G button and then D or E button to select Factory Mode.
Press the G button and then D or E button to select Low power.
Press the F or G button to select Off or On.

5 Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode G

Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode


AUTO VOLUME LEVELER
AVL automatically keeps on an equal volume level even if you change programmes.

Press the MENU button and then D or E button to select the AUDIO menu.
Sound Mode Auto Volume Balance 0 TV Speaker Digital Audio Out
Press the G button and then D or E button to select Auto Volume.
Press the G button and then D or E button to select Off or On.

Sound Mode Auto Volume G Balance 0 TV Speaker Digital Audio Out


You can select your preferred sound setting; Surround MAX, Standard, Music, Movie or Sports and you can also adjust the sound frequency of the equalizer.
Sound Mode lets you enjoy the best sound without any Special adjustment because the TV sets the appropriate sound options based on the programme content.
Surround MAX, Standard, Music, Movie, and Sports are preset for good sound quality at the factory and are not adjustable.
Sound Mode Auto Volume Balance 0 TV Speaker Digital Audio Out
Surround MAX Select this option to sound realistic. Standard The most commanding and natural audio. Music Select this option to enjoy the original sound when listening to the music. Movie Select this option to enjoy sublime sound. Sports Select this option to watch sports broadcasting. User Select this option to use the user-defined audio set- tings.

Sound Mode G Auto Volume Balance 0 TV Speaker Digital Audio Out
Press the MENU button and then D or E button to select the AUDIO menu.
Press the G button and then D or E button to select Sound Mode.
Press the G button and then D or E button to select Surround MAX, Standard, Music, Movie, Sports or User.


Press the MENU button and then D or E button to select the AUDIO menu.
Sound Mode Auto Volume Balance 0 TV Speaker Digital Audio Out
Press the G button and then D or E button to select Sound Mode.
Press the G button and then D or E button to select User.
Sound Mode G Auto Volume Balance 0 TV Speaker Digital Audio Out
Select a sound band by pressing the F or G button. Make appropriate sound level with the D or E button.

120Hz F G 200Hz 500Hz 1.2KHz 3KHz 7.5KHz 12KHz


You can adjust the sound balance of speaker to the levels you prefer.

Press the MENU button and then D or E button to select the AUDIO menu.
Sound Mode Auto Volume Balance 0 TV Speaker Digital Audio Out
Press the G button and then D or E button to select Balance.
Press the G button and then F or G button to make desired adjustment.

Sound Mode Auto Volume Balance 0 G TV Speaker Digital Audio Out


TV SPEAKERS ON/ OFF SETUP
You can adjust the internal speaker status.
In AV1, AV2, AV3, COMPONENT, RGB and HDMI1 with HDMI to DVI cable, TV speaker and/or variable audio can be outputted even though there is no video signal.
If you want to use your external hi-fi stereo system, turn off the internal speakers of the set.

Sound Mode Auto Volume Balance 0 TV Speaker Digital Audio Out
Press the MENU button and then D or E button to select the AUDIO menu.
Press the G button and then D or E button to select TV Speaker.
Press the G button and then D or E button to select Off or On.

Sound Mode Auto Volume Balance 0 TV Speaker G Digital Audio Out


This function lets you select your preferred Digital Audio Output. The set can output Dolby Digital in a channel only which broadcast Dolby Digital Audio. When it’s applied the Dolby Digital format, if you select Dolby Digital on Digital audio out menu, SPDIF Output will be out- putted Dolby Digital. Even if it’s selected Dolby Digital, when it doesn’t apply Dolby Digital format, SPDIF Output will be outputted PCM. Even if both Dolby Digital and Audio language have been set in a channel which broadcast Dolby Digital Audio, only Dolby Digital will be played.
Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories. Sound Mode Auto Volume Balance 0 TV Speaker Digital Audio Out

Press the MENU button and then D or E button to select the AUDIO menu.
Press the G button and then D or E button to select Digital Audio Out.
Press the G button and then D or E button to select Dolby Digital or PCM.

Sound Mode Auto Volume Balance 0 TV Speaker Digital Audio Out G Dolby Digital PCM

I/II
Stereo/Dual Reception (In Analogue Mode Only)
When a programme is selected, the sound information for the station appears after the programme number and station name disappear.
STEREO
DUAL I
A Mono sound selection
If the stereo signal is weak in stereo reception, you can switch to mono by pressing the I/II button twice. In mono reception, the depth of sound is improved. To switch back to stereo, press the I/II button twice again.
A Language selection for dual language broadcast
If a programme received two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II button repeatedly.
DUAL I Sends the primary broadcast language to the loudspeakers. DUAL II Sends the secondary broadcast language to the loudspeakers. DUAL I+II Sends a separate language to each loudspeaker.

If the set is equipped with the receiver for NICAM reception, the high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of received broadcast as follows by press- ing the I/II button repeatedly.
When NICAM mono is received, you can select NICAM MONO or FM MONO.
When NICAM stereo is received, you can select NICAM STEREO or FM MONO. If the stereo signal is weak, switch to FM mono.
When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II or NICAM DUAL I+II or MONO.
In AV, S-Video, Component, RGB and HDMI mode, you can select output sound for the left and right loudspeakers.
Repeatedly press the I/II button to select the sound output.
L+R: Audio signal from audio L input is sent to the left loud speaker and audio signal from audio
R input is sent to the right loud speaker. L+L: Audio signal from audio L input is sent to left and right loud speakers. R+R: Audio signal from audio R input is sent to left and right loud speakers.

ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION
Installation guide menu appears on TV screen when it is turned on for the first time.
Press the D or E or F or G button and then, OK button to select your desired language.
Press the D or E button and then, OK button to select your country.
* If you want to change Language/ Country selection
Press the MENU button and then use D or E button to select the OPTION menu.
TV/RADIO
I/II MUTE TEXT
Press the G button and then use D or E button to select Language. The menus can be shown on the screen in the selected language. Or, Press the G button and then use D or E button to select Country.
Press the G button and then use F or G button to select your desired language or country.
Press the OK button.
G If you don’t finish set up Installation Guide by pressing EXIT button or
time out of OSD (On Screen Display) display, it will continuously appear until completing set up whenever the set is turned on.
G If you select wrong local country, the teletext may not appear correctly on
the screen and some problem may happen during teletext operation.
G CI (Common Interface) function may not be applied based on country
broadcasting circumstance.
G DTV mode control buttons may not be working based on country broad-
casting circumstance.


Audio function lets you select your preferred language for audio. If the audio data in selected language is not broadcasted, default language audio will be played.
Use Subtitle function when two or more subtitle languages are broadcasted. If the subtitle data in selected language is not broadcasted, default language subtitle will be displayed.
Press the MENU button and then use D or E button to select the OPTION menu.

Press the G button and then use D or E button to select Language.
Press the G button and then use D or E button to select Audio, Subtitle or Subtitle Hard of hearing.
Press the G button and then use F or G button to select your desired language.
< Audio Language Selection >
Audio Language OSD Information
G When two or more audio languages are broadcasted, you
Status Not Available MPEG Audio Dolby Digital Audio Audio for “Visual Impaired” Audio for “Hearing Impaired”
can select audio language with the I/II button on the remote control.
G Press the D or E button to select an audio language.
G Press the F or G button to select L+R, L+L or R+R.
< Subtitle Language Selection >
Subtitle Language OSD Information
G When two or more subtitle languages are broadcasted, you
Status Not Available Teletext Subtitle
can select subtitle language with the SUBTITLE button on the remote control.
TEXT
G Press the D or E button to select a subtitle language.
Subtitle for “Hard of Hearing”
- The audio/subtitle can be displayed simpler form with 1 to 3 characters which is broadcast by service provider. - When you select supplementary Audio (Audio for “Visual/Hearing Impaired”) it may speak out a part of Main audio.
Display · Display


CLOCK SETUP
The clock is set automatically when receiving the digital signal. (You can set the clock if the TV has no DTV signal.) You must set to the time correctly before using on/off time function.

Press the MENU button and then D or E button to select the TIME menu.
Clock Off Time On Time Auto Sleep Time Zone
Press the G button and then D or E button to select Clock.
Press the G button and then F or G button to select either the year, date, or time option.
Once selected, use the D or E button to set the year, date, and time options.

Clock G Off Time On Time Auto Sleep Time Zone


The Off time automatically switches the set to standby at the preset time. Two hours after the set is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed. Once the on time/off time is set, these functions operate daily at the preset time. Off time function overrides On timer function if they are set both to the same time. The set must be in standby mode for the On timer to work.
Clock Off Time On Time Auto Sleep Time Zone
Press the MENU button and then D or E button to select the TIME menu.
Press the G button and then D or E button to select Off Time/On Time.
Press the G button and then D or E button to select On.
Press the G button and then D or E button to set the hour.

Clock Off Time On Time G Auto Sleep Time Zone
Press the G button and then D or E button to set the minutes.
For only On time function


AUTO SHUT-OFF SETTING
If set to on and there is no input signal, the set turns off auto- matically after 10 minutes.

Press the MENU button and then D or E button to select the TIME menu.
Clock Off Time On Time Auto Sleep Time Zone
Press the G button and then D or E button to select Auto Sleep.
Press the G button and then D or E button to select Off or On.

Clock Off Time On Time Auto Sleep G Time Zone


When you select a Time Zone city, TV time is set by the time offset information based on Time Zone and GMT (Greenwich Mean Time) information which is received to broadcasting signal when time is set automatically by a digital signal.

Press the MENU button and then D or E button to select the TIME menu.
Press the G button and then D or E button to select Time Zone.
Press the G button and then F or G button to select your viewing area time zone.
Clock Off Time On Time Auto Sleep Time Zone

Clock Off Time On Time Auto Sleep Time Zone G
You don’t have to remember to switch the set off before you go to sleep. The sleep timer automatically switches the set to standby after the preset time has elapsed.

Press the SLEEP button repeatedly to select the num- ber of minutes.
The display ‘ - - - Min. ’ will appear on the screen, fol- lowed by 10, 20, 30, 60, 90, 120, 180 and 240.
When the number of minutes you want is displayed on the screen, the timer begins to count down from the number of minutes selected.
To view the remaining sleep time, press the SLEEP but- ton once.
To cancel the sleep time, repeatedly press the SLEEP button until the display ‘ - - - Min. ’ appears.
When you switch the set off, the set releases the pre- set sleep time.


If you first enter the password, press ‘0’, ‘0’, ‘0’, ‘0’ on the remote control handset.

Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode
Press the MENU button and then D or E button to select the OPTION menu.
Press the G button and then D or E button to select Lock System.
Press the G button and then F or G button to select On.
Press the G button and then use NUMBER buttons to input a 4-digit password.

Language Country Lock System G Parental Control Input Label SIMPLINK Factory Mode
If you forgot your password, press ‘7’, ‘7’, ‘7’, ‘7’ on the remote control handset.


This function operates according to information from the broadcasting station. Therefore if the signal has wrong infor- mation, this function dose not operates.
Lets you set up blocking schemes to block specific channels, ratings, and external viewing sources.
A password is required to gain access to this menu.
This set is programmed to remember which option it was last set to even if you turn the set off.
Press the MENU button and then D or E button to select the OPTION menu.
Press the G button and then D or E button to select Parental Control. Then, press the G button to enter the password as requested. The TV is set up with the initial password “0-0-0-0”.
Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode
Press the G button and then D or E button to select Parental Guidance or Key Lock.
Parental Guidance (In Digital mode only) Prevents children from watching certain adult’s TV pro- grammes, according to the ratings limit set. Key Lock The set can be set so that the remote control is needed to control it. This feature can be used to pre- vent unauthorized viewing.

Language Country Lock System Parental Control G Input Label SIMPLINK Factory Mode
Press the F or G button to make appropriate adjust- ments.

In Key Lock ‘On’, if the set is turned off, press the r / I, INPUT, PR D or E button on the set or POWER, INPUT, D/A TV, PR + or - or NUMBER buttons on the remote control.
With the Key Lock On, the display ‘ Key Lock On ’ appears on the screen if any button on the front panel is pressed while viewing the set.

This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics.
The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard tele- text) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information.
Press the TEXT button to switch to teletext. The initial page or last page appears on the screen. Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the TEXT or EXIT button to switch off teletext. The previous mode reappears.
Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number. The PR+ or - button can be used to select the preceding or following page.
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block.
With the blue button you can progress from block to block. Use the yellow button to proceed to the next group with automatic overflow to the next block. With the green button you can proceed to the next existing page with automatic overflow to the next group.
Alternatively the PR+ button can be used. The red button permits to return to previous selection. Alternatively the PR- button can be used.
Corresponding to the SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode.

The teletext pages are colour coded along the bottom of the screen and are selected by pressing the correspond- ing coloured button.
Press the button to select the index page. You can select the pages which are colour coded along the bottom line with the same coloured buttons. Corresponding to the SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in FASTEXT mode. The PR+ or - button can be used to select the preceding or following page.
Press this button to display concealed information, such as solutions of riddles or puzzles. Press this button again to remove the information from the display.
Displays the TV picture on the screen while waiting for the new teletext page. The display will appear at the top left hand corner of the screen. When the updated page is available then display will change to the page number. Press this button to view the updated teletext page.
When viewing a TV programme, press this button to display the time at the top right hand corner of the screen. Press this button again to remove the display. In the teletext mode, press this button to select a sub page num- ber. The sub page number is displayed at the bottom of the screen. To hold or change the sub page, press the RED/GREEN, PR+ or - or NUMBER buttons. Press again to exit this function.
Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The num- ber of sub pages and the sub page displayed is, usually, shown on the screen below the time. When this button is pressed the stop symbol is displayed at the top left-hand corner of the screen and the automatic page change is inhibited. To continue press this button again.
A Page selection

*This function works in UK only.
The set gives you access to a digital teletext which is greatly improved in various aspects such as text, graphics and so on. This digital teletext can be accessed by special digital teletext services and specific services which broadcast digital teletext. You should select off from the subtitle language to display teletext by pressing SUBTITLE button.
Press the numeric or PR + or - button to select a digital service which broadcasts digital teletext. To know which are digital teletext services, refer to the EPG service list.

Follow the indications on digital teletext and move onto the next step by pressing TEXT, OK, D or E, F or G, RED, GREEN, YELLOW, BLUE or NUMBER buttons and so on.
To change digital teletext service, just select a different service by the numeric or PR + or - button.
If pressing the MENU, GUIDE or INFO i button, the teletext service disappear temporarily. When pressing these buttons again, the teletext service is appeared.
Press the numeric or PR + or - button to select a certain service which broadcasts digital teletext.

Press the TEXT or colour button to switch on teletext.
Follow the indications on digital teletext and move onto the next step by pressing OK, D or E, F or G, RED, GREEN, YELLOW, BLUE or NUMBER buttons and so on.
Press the TEXT or colour button to switch off digital tele- text and return to TV viewing.
Some services may allow you to access text services by pressing the RED button.
If pressing the MENU, GUIDE or INFO i button, the teletext service disappear temporarily. When pressing these buttons again, the teletext service is appeared.

TROUBLESHOOTING
The operation does not work normally.
A Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
A Ensure that the batteries are installed with correct polarity (+ to +, - to -).
A Ensure that the correct remote operating mode is set: TV, VCR etc.
A Install new batteries.
A Is the sleep timer set?
A Check the power control settings. Power interrupted.
A No broadcast on station tuned with Auto sleep activated.
The video function does not work.
A Check whether the product is turned on.
A Try another channel. The problem may be with the broadcast.
A Is the power cord inserted into wall power outlet?
No picture &No sound
A Check your antenna direction and/or location.
A Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
A This is normal, the image is muted during the product startup process. Please
contact your service centre, if the picture has not appeared after five minutes.
A Adjust Colour in menu option.
A Keep a sufficient distance between the product and the VCR.
No or poor colour
A Try another channel. The problem may be with the broadcast.
A Are the video cables installed properly?
A Activate any function to restore the brightness of the picture.
A Check for local interference such as an electrical appliance or power tool.
A Station or cable product experiencing problems, tune to another station.
A Station signal is weak, reorient antenna to receive weaker station.
A Check for sources of possible interference.
A Check antenna (Change the direction of the antenna).

The audio function does not work.
A Press the VOL + or - button.
A Sound muted? Press MUTE button.
Picture OK & No sound
A Try another channel. The problem may be with the broadcast.
A Are the audio cables installed properly?
No output from one
A Adjust Balance in menu option.
A A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the product.
There is a problem in PC mode. (Only PC mode applied)
A Adjust resolution, horizontal frequency, or vertical frequency.
The signal is out of range
A Check the input source.
Vertical bar or stripe on
background & Horizontal Noise &
A Work the Auto configure or adjust clock, phase, or H/V position. (Option)
Screen colour is unstable
A Check the signal cable.
A Reinstall the PC video card.

Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
ATo remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
APlease be sure not to use a wet cloth.
G If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.

PRODUCT SPECIFICATIONS
32LC4*
37LC4*
42LC4*
MODELS
26LC45-ZA 26LC46-ZC
32LC45-ZA 32LC46-ZC
37LC45-ZA 37LC46-ZC
42LC45-ZA 42LC46-ZC
676.4 x 529.2x 221.0 mm
806.8 x 605.6 x 249.0 mm
926.6 x 697.6x 280.4mm
1032.7 x 750.0 x 287.6 mm
(Width x Height x Depth)
26.6 x 20.8 x 8.7 inches
31.8 x 23.9 x 9.8 inches
36.5x 27.5 x 11.0 inches
40.7x 29.5 x 11.3 inches
676.4 x 474.5 x 85.0 mm
806.8 x 548.6 x 79.0 mm
926.6 x 635.6 x 88.0mm
1032.7 x 685.5 x 88.5 mm
26.6 x 18.7 x 3.3 inches
31.8 x 21.6x 3.1 inches
36.5x 25.0 x 3.5 inches
40.7 x 27.0 x 3.5 inches
10.04kg / 22.1 lbs
13.8 kg / 30.5 lbs
20.0 kg / 44.1 lbs
24.5 kg / 54.0 lbs
9.04kg / 19.9 lbs
10.7 kg / 23.6 lbs
16.3 kg / 35.9 lbs
20 kg / 44.1 lbs
AC100-240V~50/60Hz 1.3A
AC100-240V~50/60Hz 1.5A
AC100-240V~50/60Hz 1.8A
AC100-240V~50/60Hz 2.3A
150W
180W
230W
26LC5*
32LC5*
37LC5*
42LC5*
42LC55-ZA MODELS
26LC55-ZA
32LC55-ZA 32LC56-ZC
37LC55-ZA
676.4 x 529.2x 221.0 mm
806.6 x 606.5 x 249.0 mm
927.0 x 692.8x 280.5mm
1033.1 x 749.5 x 287.6 mm
26.7 x 20.9 x 8.7 inches
31.8 x 23.9 x 9.8 inches
36.5x 27.3 x 11.1 inches
40.7x 29.5 x 11.3 inches
(Width x Height x Depth)
676.4 x 478.7 x 84.0 mm
806.6 x 552.3 x 79 mm
927.0 x 630.0 x 88.0mm
1033.4 x 686.8 x 88.5mm
26.7 x 18.9 x 3.3 inches
31.8 x 21.8x 3.1 inches
36.5x 24.8 x 3.5 inches
40.7 x 27.0x 3.5inches
10.04kg / 22.2 lbs
14.1kg / 31.1 lbs
20.0 kg / 44.1 lbs
24.5 kg / 54.1 lbs
8.62kg / 19.0 lbs
11.2kg / 24.7 lbs
16.0 kg / 35.3 lbs
20.4 kg / 45.0 lbs
AC100-240V~50/60Hz 1.3A
AC100-240V~50/60Hz 1.5A
AC100-240V~50/60Hz 1.8A
AC100-240V~50/60Hz 2.3A
150W
180W
230W
PAL/SECAM B/G/D/K, PAL I/II, SECAM L/L’
VHF: E2 ~ E12, UHF: E21 ~ E69, CATV: S1 ~ S20, HYPER: S21 ~ S47
75 Ω
0 ~ 40°C / 32 ~ 104°F
-20 ~ 60°C / -4 ~ 140°F

32LB7*
42PC3*
50PC3*
MODELS
26LB75-ZE 26LB76-ZF
32LB75-ZB 32LB76-ZD
42PC35-ZC
50PC35-ZC
671.8x539.8x254.2 mm
805.8x619.7x283.9 mm
1129.0 x 748.5 x 333.6 mm
1302.6 x 872 x 355.8 mm
(Width x Height x Depth)
26.4x21.2x10 inches
31.7x24.4x11.2 inches
44.4 x 29.5 x 13.1 inches
51.3 x 34.3 x 14 inches
671.8x476.1x85 mm
805.8x554.1x79.0 mm
1129.0 x 695.0 x 103.7 mm
1302.6 x 810x 107.7 mm
26.4x18.7x3.3 inches
31.7x21.8x3.1 inches
44.4 x 27.4 x 4.1 inches
51.3 x 31.9 x 4.2 inches
14 kg / 30.9 lbs
14.8 kg / 32.6 lbs
31.5 kg / 69.4 lbs
51.9 kg / 114.4 lbs
11 kg / 24.3 lbs
12.6 kg / 27.8 lbs
24.2 kg / 53.3 lbs
43.1 kg / 95 lbs
AC100-240V~50/60Hz 1.3A
AC100-240V~50/60Hz 1.5A
AC100-240V~ 50/60Hz 3.5A
AC100-240V~ 50/60Hz 4.5A
150W
330W
450W
42PC5*
50PC5*
50PB6*
60PC4*
60PC45-ZB MODELS
50PB65-ZA
42PC55-ZB 42PC56-ZD
50PC55-ZB 50PC56-ZD
1048.0 x 766.0 x 310.0 mm
1242.0 x 887.6 x 370.0mm
1359.9 x 889.2 x 369.8 mm
1548 x 1061 x 448 mm
41.3 x 30.2 x 12.2 inches
48.9 x 34.9 x 14.6 inches
53.6 x 35.1 x 14.6 inches
60.9 x 41.8 x 17.6 inches
(Width x Height x Depth)
1048.0 x 713.0 x 83.5 mm
1242.0 x 827.2 x 88.0 mm
1359.9 x 822.5 x 89.5 mm
1548 x 988 x 98.5 mm
41.3 x 28.1 x 3.3 inches
48.9 x 32.6 x 3.5 inches
53.6 x 32.4 x 3.6 inches
60.9 x 38.9 x 3.9 inches
28.0 kg / 61.7 lbs
39.3 kg / 86.6 lbs
48.0 kg / 105.9 lbs
72.5 kg / 159.8 lbs
24.6kg / 54.2 lbs
34.6kg / 76.2 lbs
39.1 kg / 86.2 lbs
60.0 kg / 132.2 lbs
AC100-240V~50/60Hz 3.5A
AC100-240V~50/60Hz 5.0A
AC100-240V~50/60Hz 5.0A
AC100-240V~50/60Hz 5.8A
450W
450W
580W
PAL/SECAM B/G/D/K, PAL I/II, SECAM L/L’
VHF: E2 ~ E12, UHF: E21 ~ E69, CATV: S1 ~ S20, HYPER: S21 ~ S47
APPENDIX
0 ~ 40°C / 32 ~ 104°F
-20 ~ 60°C / -4 ~ 140°F
A The specifications shown above may be changed without prior notice for quality improvement.

PROGRAMMING THE REMOTE CONTROL
The remote is a multi-brand or a universal remote. It can be programmed to operate most remote-con- trollable devices of other manufacturers. Note that the remote may not control all models of other brands.
Test your remote control. To find out whether your remote control can operate the component without programming, turn on the component such as a VCR and press the corresponding mode button (such as a DVD or VCR) on the remote control, while pointing at the component. Test the POWER and PR + / - buttons to see if the component responds properly. If not, the remote requires programming to operate the device.
Turn on the component to be programmed, then press the corresponding mode button (such as a DVD or VCR) on the remote control. The remote control button of desired device is lighted.
Press the MENU and MUTE buttons simultaneously, the remote control is ready to be programmed for the code.
Enter a code number using the number buttons on the remote control. Programming code numbers for the corresponding component can be found on the following pages. Again, if the code is correct, the device will turn off.
Press the MENU button to store the code.
Test the remote control functions to see if the component responds properly. If not, repeat from step 2.
PROGRAMMING CODE
Brand Codes Brand Codes Brand Codes DVD
APEX DIGITAL 022 DENON 020 014 GE 005 006 HARMAN KARDON 027 JVC 012 LG 001 010 016 025 MAGNAVOX 013 MARANTZ 024
MITSUBISHI 002 NAD 023 ONKYO 008 017 PANASONIC 003 009 PHILIPS 013 PIONEER 004 026 PROCEED 021 PROSCAN 005 006
RCA 005 006 SAMSUNG 011 015 SONY 007 THOMPSON 005 006 TOSHIBA 019 008 YAMAHA 009 018 ZENITH 010 016 025

Brand Codes Brand Codes Brand Codes
MAGNAVOX 031 033 034 041 067 068 MARANTZ 012 031 033 067 069 MARTA 101 MATSUI 027 030 MEI 031 033 MEMOREX 003 010 014 031 033 034 053 072 101 102 134 139 MGA 045 046 059 MINOLTA 013 020 MITSUBISHI 013 020 045 046 049 051 059 061 151 MTC 034 040 MULTITECH 024 034 NEC 012 023 039 043 048 NORDMENDE 043 OPTONICA 053 054 PANASONIC 066 070 074 083 133 140 145
SAMSUNG 032 040 102 104 105 107 109 112 113 115 120 122 125 SANSUI 022 043 048 135 SANYO 003 007 010 014 102 134 SCOTT 017 037 112 129 131 SEARS 003 008 009 010 013 014 017 020 031 042 073 081 101 SHARP 031 054 149 SHINTOM 024 SONY 003 009 031 052 056 057 058 076 077 078 149 SOUNDESIGN 034 STS 013 SYLVANIA 031 033 034 059 067 SYMPHONIC 034 TANDY 010 034 TATUNG 039 043 TEAC 034 039 043 TECHNICS 031 033 070 TEKNIKA 019 031 033 034 101 THOMAS 034 TMK 006 TOSHIBA 008 013 042 047 059 082 112 131 TOTEVISION 040 101 UNITECH 040 VECTOR RESEARCH 012 VICTOR 048 VIDEO CONCEPTS 012 034 046 VIDEOSONIC 040 WARDS 003 013 017 024 031 033 034 040 053 054 131 YAMAHA 012 034 039 043 ZENITH 034 048 056 058 072 080 101
AIWA 034 AKAI 016 043 046 124 125 146 AMPRO 072 ANAM 031 033 103 AUDIO DYNAMICS 012 023 039 043 BROKSONIC 035 037 129 CANON 028 031 033 CAPEHART 108 CRAIG 003 040 135 CURTIS MATHES 031 033 041 DAEWOO 005 007 010 064 065 108 110 111 112 116 117 119 DAYTRON 108 DBX 012 023 039 043 DYNATECH 034 053 ELECTROHOME 059 EMERSON 006 017 025 027 029 031 034 035 036 037 046 101 129 131 138 153 FISHER 003 008 009 010 FUNAI 034 GE 031 033 063 072 107 109 144 147 GO VIDEO 132 136 HARMAN KARDON 012 045 HITACHI 004 018 026 034 043 063 137 150 INSTANTREPLAY 031 033 JCL 031 033 JCPENNY 012 013 015 033 040 066 101 JENSEN 043 JVC 012 031 033 043 048 050 055 060 130 150 152 KENWOOD 014 034 039 043 047 048 LG (GOLDSTAR) 001 012 013 020 101 106 114 123 LLOYD 034 LXI 003 009 013 014 017 034 101 106 MAGIN 040
PENTAX 013 020 031 033 063 PHILCO 031 034 067 PHILIPS 031 033 034 054 067 071 101 PILOT 101 PIONEER 013 021 048 PORTLAND 108 PULSAR 072 QUARTZ 011 014 QUASAR 033 066 075 145 RCA 013 020 033 034 040 041 062 063 107 109 140 144 145 147 REALISTIC 003 008 010 014 031 033 034 040 053 054 101 RICO 058 RUNCO 148 SALORA 014

IR CODES
1. How to Connect
A Connect your wired remote control to the Remote Control port on the TV.
Single pulse, modulated with 37.917KHz signal at 455KHz
FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3
A Configuration of frame
Lead code Low custom code High custom code Data code Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
4.5 ms 9 ms
0.55 ms
2.25 ms 9 ms
Bit ”0” Bit ”1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
The waveform is transmitted as long as a key is depressed.

Code (Hexa) Function Note
00 01 02 03 40 41 06 07 08 09 10 11 12 13 14 15 16 17 18 19 0B AA AB 56 5B 1E 1A 50 F0 7E E0 E1 0A 0E 43 44 53 20 2A 26 28 62 70 65 61 63 71 72 79 B0 BA B2 B3
PR + PR - VOL + VOL - Up (D) Down (E) Right (G) Left (F) POWER MUTE Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 INPUT INFO i GUIDE SUBTITLE EXIT FAV Q.VIEW D/A TV TV/RADIO SIMPLINK BRIGHT + BRIGHT - I/II SLEEP MENU OK( ) LIST TEXT REVEAL TIME BACK UPDATE INDEX HOLD BLUE Key YELLOW Key GREEN Key RED Key RATIO
R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON (POWER ON/OFF) R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON
G II I FF
GG I
8F 8E B1 BD
FF
GG
A
O

EXTERNAL CONTROL DEVICE SETUP
RS-232C Setup

Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Note: RS-232C connection cables are not supplied with the product.

RS-232C Configurations
7-Wire Configurations (Standard RS-232C cable)
PC TV
RXD 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DSR DSR 6 4 DTR RTS 7 8 CTS CTS 8 7 RTS
RXD 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DTR DSR 6 4 DSR RTS 7 7 RTS CTS 8 8 CTS
D-Sub 9 D-Sub 9
D-Sub 9 D-Sub 9
3-Wire Configurations(Not standard)


Use this function to specify a set ID number. Refer to ‘Real Data Mapping’. G p.113

Press the MENU button and then use D or E button to select the OPTION menu.
Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode
Press the G button and then use D or E button to select Factory Mode.
Press the G button and then use D or E button to select Set ID.

Press the F or G button to adjust Set ID to choose the desired TV ID number. The adjustment range of SET ID is 1~99.
Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode G
Press EXIT button to return to normal TV viewing.

Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode

Communication Parameters
AUse a crossed (reverse) cable.
Transmission / Receiving Protocol Command Reference List
1 COMMAND
[Command1][Command2][ ][Set ID][ ][Data][Cr]
01. Power k a 0 ~ 1 02. Input Select k b Refer to p. 111 03. Aspect Ratio k c Refer to p. 111 04. Screen Mute k d 0 ~ 1 05. Volume Mute k e 0 ~ 1 06. Volume Control k f 0 ~ 64 07. Contrast k g 0 ~ 64 08. Brightness k h 0 ~ 64 09. Colour k i 0 ~ 64 10. Tint k j 0 ~ 64 11. Sharpness k k 0 ~ 64 12. OSD Select k l 0 ~ 1 13. Remote control lock mode k m 0 ~ 1 14. Balance k t 0 ~ 64 15. Colour Temperature k u 0 ~ 3 16. Red Adjustment k v 0 ~ 50 17. Green Adjustment k w 0 ~ 50 18. Blue Adjustment k $ 0 ~ 50 19. Abnormal Status k z 0 ~ 9 20. ISM Method j p Refer to p. 113 21. Low Power j q 0 ~ 1 22. Auto Configure j u 1 23. Channel Select Command m a Refer to p. 114 24. Send IR Code m c Key Code 25. Input select (Main) x b Refer to p. 114
* [Command 1] : First command to control the set. (j, k, m or x) * [Command 2] : Second command to control the set. * [Set ID] : You can adjust the set ID to choose
desired monitor ID number in option menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected the set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol. * [DATA] : To transmit command data.
Transmit ‘FF’ data to read status of command. * [Cr] : Carriage Return
ASCII code ‘0x0D’ * [ ] : ASCII code ‘space (0x20)’
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
* When setting the 19 ~ 25, a menu doesn’t display on screen.
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors.

G To control Power On/Off of the set. Transmission
G To select screen mute on/off. Transmission
[k][a][ ][Set ID][ ][Data][Cr]
[k][d][ ][Set ID][ ][Data][Cr]
[a][ ][Set ID][ ][OK][Data][x]
[d][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off. Transmission
[k][a][ ][Set ID][ ][FF][Cr]
G To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control. Transmission
[a][ ][Set ID][ ][OK][Data][x]
* In like manner, if other functions transmit ‘0xFF’ data based on this format, Acknowledgement data feed back presents status about each function.
[k][e][ ][Set ID][ ][Data][Cr]
[e][ ][Set ID][ ][OK][Data][x]
G To select input source for the set.
You can also select an input source using the INPUT button on the set's remote control.
G To adjust volume.
You can also adjust volume with the VOLUME buttons on remote control. Transmission
[k][b][ ][Set ID][ ][Data][Cr]
[k][f][ ][Set ID][ ][Data][Cr]
* Refer to ‘Real data mapping 1’. See page 113.
[f][ ][Set ID][ ][OK][Data][x]
[b][ ][Set ID][ ][OK][Data][x]
G To adjust screen contrast.
You can also adjust contrast in the PICTURE menu. Transmission
G To adjust the screen format. (Main picture format)
You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the SCREEN menu. Transmission
[k][g][ ][Set ID][ ][Data][Cr]
* Refer to ‘Real data mapping 1’. See page 113.
[k][c][ ][Set ID][ ][Data][Cr]
[g][ ][Set ID][ ][OK][Data][x]
G To adjust screen brightness.
You can also adjust brightness in the PICTURE menu. Transmission
[c][ ][Set ID][ ][OK][Data][x]
[k][h][ ][Set ID][ ][Data][Cr]
* Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.
* Refer to ‘Real data mapping 1’. See page 113.
[h][ ][Set ID][ ][OK][Data][x]

G To adjust the screen colour.
G To adjust balance.
You can also adjust colour in the PICTURE menu. Transmission
You can also adjust balance in the AUDIO menu. Transmission
[k][i][ ][Set ID][ ][Data][Cr]
[k][t][ ][Set ID][ ][Data][Cr]
* Refer to ‘Real data mapping 1’. See page 113.
* Refer to ‘Real data mapping 1’. See page 113.
[i][ ][Set ID][ ][OK][Data][x]
[t][ ][Set ID][ ][OK][Data][x]
G To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
G To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu. Transmission
[k][j][ ][Set ID][ ][Data][Cr]
[k][u][ ][Set ID][ ][Data][Cr]
* Refer to ‘Real data mapping 1’. See page 113.
[j][ ][Set ID][ ][OK][Data][x]
[u][ ][Set ID][ ][OK][Data][x]
G To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu. Transmission
G To adjust red in colour temperature. Transmission
[k][k][ ][Set ID][ ][Data][Cr]
[k][v][ ][Set ID][ ][Data][Cr]
* Refer to ‘Real data mapping 1’. See page 113.
* Refer to ‘Real data mapping 2’. See page 113.
[k][ ][Set ID][ ][OK][Data][x]
[v][ ][Set ID][ ][OK][Data][x]
G To select OSD (On Screen Display) on/off when con-
trolling remotely.
G To adjust green in colour temperature. Transmission
[k][l][ ][Set ID][ ][Data][Cr]
[k][w][ ][Set ID][ ][Data][Cr]
* Refer to ‘Real data mapping 2’. See page 113.
[l][ ][Set ID][ ][OK][Data][x]
[w][ ][Set ID][ ][OK][Data][x]
G To lock the front panel controls on the monitor and
remote control. Transmission
G To adjust blue in colour temperature. Transmission
[k][m][ ][Set ID][ ][Data][Cr]
[k][$][ ][Set ID][ ][Data][Cr]
[m][ ][Set ID][ ][OK][Data][x]
* Refer to ‘Real data mapping 2’. See page 113.
* If you’re not using the remote control, use this mode. When main power is on/off, external control lock is released.
[$][ ][Set ID][ ][OK][Data][x]

G To recognize an abnormal state. Transmission
G To reduce the power consumption of the set. You can
also adjust Low Power in OPTION menu. It’s not available to use this function in LCD TV models. Transmission
[k][z][ ][Set ID][ ][FF][ ][Cr]
[z][ ][Set ID][ ][OK][Data][x]
[j][q][ ][Set ID][ ][Data][ ][Cr]
[q][ ][Set ID][ ][OK/NG][Data][x]
* This function is “read only”.
G To control the ISM method. You can also adjust ISM
Method in OPTION menu. It’s not available to use this function in LCD TV models. Transmission
[j][p][ ][Set ID][ ][Data][Cr]
[p][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping 1
* Real data mapping 2
28 :0
Ack · Ack · Ack

G To adjust picture position and minimize image shaking
G To select input source for main picture. Transmission
automatically. It works only in RGB (PC) mode. Transmission
[x][b][ ][Set ID][ ][Data][Cr]
[j][u][ ][Set ID][ ][Data][Cr]
[u][ ][Set ID][ ][OK/NG][Data][x]
0
External Input Input Number
G Select channel to following physical number. Transmission
0 0 0 1 Analogue
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Data0 :High channel data Data1 :Low channel data
0 0 1 1 Component
ex. No. 47 -> 00 2F (2FH) No. 394 -> 01 88 (188H), DTV No. 0 -> Don’t care Data2 0x00 : ATV Main
0 1 0 1 HDMI
Analogue - Min: 00 ~ Max: 63 (0~99) Digital - Min: 00 ~ Max: 3E7 (0~999)
0 Input1
0 0 0 1 Input2
[a][ ][Set ID][ ][OK/NG][Data][x]
0 0 1 0 Input3
0 0 1 1 Input4
[b][ ][Set ID][ ][OK/NG][Data][x]
G To send IR remote key code. Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Data Key code - Refer to page 107.
[c][ ][Set ID][ ][OK/NG][Data][x]








Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.