


No part of this document may be reproduced in any form or by any means without the express written consent of UPS Aviation Technologies, Inc.
II Morrow, UPS Aviation Technologies, and Apollo are trademarks of UPS Aviation Technologies, Inc. © 2001 by UPS Aviation Technologies, Inc. All rights reserved. Printed in the U.S.A.
UPS Aviation Technologies, Inc. Consumer Products Division 2345 Turner Road, S.E. Salem, OR 97302
U.S.A. Toll Free 800.525.6726 Canada Toll Free 800.654.3415 International 503.391.3411 FAX 503.364.2138
Visit our web page at http://www.upsat.com Send comments about this manual by email to: techpubs@at.ups.com

Welcome ...
Welcome to a new era of aviation navigation. Once again, II Morrow Inc. has set new standards in features and ease of use for the general aviation public. The Apollo GX-series of products are unequaled in providing the features, level of performance, and reliability that aviation users require. The Apollo GX-series sets a precedent that will be the standard to which all other avionics will be compared.
The Apollo GX50 is a full-featured GPS receiver that is IFR-certified for non-precision approach. The GX55 GPS receiver is IFR-certified for en route operation and designed to slide into your existing Apollo Loran or Flybuddy GPS receiver mounting tube. The GX60 combines the features of the GX50 with a revolutionary comm radio. The GX65 has the comm features of the GX60, but is not IFR approach certified and does not have the approach features.
You can be confident in knowing that you are the owner of the state-of-the-art in aviation navigation and communication. Our products are built to last and to satisfy your navigation needs.
Read the Introduction and Getting Started sections of the User’s Guide before you use your Apollo GX; these sections will give you the “rules of the road.” You can then refer to the other sections as a reference for the power you have at your fingertips with the most comprehensive navigation equipment available.
You will note that your User’s Guide may be missing some sections. This guide serves the entire family of Apollo GX products, but will only include the sections that reflect the features available in the product that you purchased. If you have an interest in the features and operation of the other models, see the section on Ordering Information.

Revision Date Software Ver. Manual P/N January 1998 2.1 560-0961-00 June 1998 2.2 560-0961-01 January 1999 2.2 560-0961-01a March 1999 3.0 560-0961-02 July 2001 3.3 560-0961-03
To receive additional copies of the Apollo GX50/55/60/65 manuals order the following part numbers: User’s Guide 560-0961-xx Approach User’s Guide Insert 560-0928-xx GX60/65 Comm User’s Guide Insert 560-0963-xx User’s Guide Binder (1") 560-9000 User’s Guide Binder (3/4”) 560-9002 User’s Guide Binder (1-1/2”) 560-9005 GX50/60/65 Installation Manual 560-0959-xx GX50/60/65 SW Ver 3.3 Installation Manual Upgrade Supplement 561-0275-xx A-33 Antenna Installation Guide 560-0949-xx GX55 Installation Manual 560-0960-xx GX50 Quick Reference 561-0238-xx GX55 Quick Reference 561-0237-xx GX60/65 Quick Reference 561-0236-xx GX65 User’s Guide Insert 561-0256-xx

The Global Positioning System (GPS) is operated by the United States Department of Defense which is solely responsible for the accuracy, daily operation, and maintenance of the satellite constellation. System accuracy is affected by the Department of Defense’s Selective Availability (SA) and the Dilution of Precision (DOP) attributed to poor satellite geometry.
Due to implementation of Selective Availability by the United States Department of Defense (DoD), all GPS receivers may suffer degradation of position accuracy. The DoD has stated that 95% of the time horizontal accuracy will not be degraded more than 100 m and 99.9% of the time accuracy will not be degraded more than 300 m.
Installations of TSO C-129a authorized Apollo GX50/60’s and TSO-C-129 authorized GX55’s may be approved for supplemental navigation only. The Apollo GX50, GX55, or GX60 may be used as the primary navigation data display, however, other means of navigation appropriate to the intended route of flight must be installed and operational. It is not required that these other systems be monitored.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference during residential use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Changes or modifications to this equipment not expressly approved by II Morrow Inc. could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règiement sur le matériel brouiileur du Canada.
FCC Notice · Canadian Notice

The SMALL knob is the smaller, inner knob of the two concentric rotary knobs used to look at or change information on the display. When only the SMALL knob is shown next to an example, turn the SMALL knob.
The LARGE knob is the larger, outer knob of the two concentric rotary knobs used to look at or change information on the display. The LARGE knob graphic shows both of the concentric knobs. Turn the LARGE, outer knob when this graphic is shown next to an example.
ENTER Text in all caps and bold indicates the key to press.
A graphic key on the side of the page refers to the key you should press for the given example. There are two types of keys: hard keys and smart keys.
A “hard” key is a permanent key on the right side of the front panel. The NAV key example shown here is a “hard” key.
The “smart” keys are five small keys below the display. The key label is shown above the key on the display and may change depending on the function you are using. Press the key below the label to access the function.
Text in a display example with an underline indicates the text will flash. In the example below, the field labeled “01:23” is underlined to indicate that it is flashing and ready for editing. The flashing characters on the display are changed by turning the SMALL knob. The GX55 is shown below as an example for the control locations.
Flashing field Large, Outer
ete SLE 1.006 Brg 126 123nm
01:23 “
ENTER MAP D
SYS FPL DB MSG


This guide describes the operation of the Apollo GX line of products. The GX50 and GX55 are GPS receivers. The GX60/65 models combine the GPS receiver with a VHF comm radio in a single package.
Apollo GX Features The Apollo GX products are high performance GPS products with a high resolution moving map display configured in a 2 inch high by 6.25 inch wide standard package. The Apollo GX’s use a powerful, accurate 8-channel GPS engine designed specifically for high performance aviation use. The 160 by 80 pixel electroluminescent display uses an automatic intensity control to keep it easily readable in all conditions from direct sunlight to the dark of night.
Power Photocell Nearest Waypoint Navigation
ete SLE 01:23 1.006 Brg 126 123nm “
NAV NRST INFO SEL
ENTER MAP D
SYS FPL DB MSG
Direct To Map Mode Smart Keys
Apollo GX Front Panel Description
A wealth of easy to use features serve the needs of today’s demanding aviation requirements. The large waypoint database has information about airports, VORs, NDBs, intersections, and special use airspaces that makes the Apollo GX an encyclopedia of aviation. It’s what you’d expect from II Morrow, the first to provide a database in a general aviation navigation aid. The database can be updated by simply changing the removable data card in the front of the unit. The database can also include 500 custom waypoints created by the user. Thirty flight plans can

be saved with up to twenty legs for setting up custom tailored routes. The detailed Navigation information displays are also customizable and can be set to automatically scroll through the desired information. The Nearest/Emergency Search feature, invented by II Morrow (UPS Aviation Technologies), makes it easy to react to an emergency or change your active flight plan.
GX55 The GX55 is designed to be simple slide-in, pin-compatible replacement for panel-mounted Apollo Loran and Flybuddy GPS receivers. The GX55 connectors and antenna footprint are the same as the Apollo Loran and Flybuddy GPS receivers. The GX55 is TSO-C129 Class A2 authorized for IFR en route and terminal operation.
GX50 The Apollo GX50 GPS receiver possesses all of the performance features of the GX55, plus more. The GX50 is TSO-C129a Class A1 authorized for IFR non-precision approach operation. The GX50 uses the same tray size, but different connections on the back to allow for approach capabilities.
GX60 The Apollo GX60 combines the physical package of the GX50 GPS receiver with a revolutionary VHF Comm transceiver. All of this without the requirement for external cooling.
GX65 The Apollo GX65 possesses the same features as the GX60, except it is not certified for IFR approaches.
Display The display is a 160 by 80 pixel electroluminescent graphic display. A photocell is located in the top left corner of the front panel display. The photocell automatically controls the light intensity of the display from low brightness at night to high brightness during daylight operation.
Introduction

External Annunciators When external indicators are installed, the Apollo GX will also provide an external indication when Parallel Track (PTK) is activated or a Message (MSG) is received. The GX50/60 also have external annunciator controls for OBS/Hold and Approach Active. “Hold” refers to suspending waypoint sequencing.
Controls The Apollo GX uses a variety of controls to manage the features. The controls include a power knob, dual-concentric knobs (called LARGE and SMALL), hard keys, and “smart” keys.
Power Knob The knob on the top right side of the Apollo GX controls power on/off. Rotate the knob clockwise (CW) past the detent to turn the power on. Rotate the knob fully counterclockwise to turn the power off. Full rotation and the push-pull capabilities are only used in the GX60/65.
Power/Volume/Squelch Knob(GX60/65) The knob on the right side of the GX60/65 controls power on/off, volume, and squelch test. Rotate the knob clockwise (CW) past the detent to turn the power on. Continue rotating the knob to the right to increase speaker and headphone amplifier volume level. Rotate the knob to the left to reduce the volume level. Pull the knob out to disable automatic squelch.
SMALL and LARGE Knobs The dual concentric knobs on the right side of the front panel are used to select pages, edit characters and values, or other options. The LARGE knob moves the cursor and the SMALL knob changes characters. Either may change pages depending on the function.
Introduction

Keys There are two types of keys that allow you access to the functions in your Apollo GX: permanent “hard” keys and displayed “smart” keys. Seven back lighted permanent keys are used to reach the functions or perform other operations of the Apollo GX. The “smart” key labels are shown on the bottom of the display. There are two categories of “smart” keys: those available for the Map function and those available at all other times. Press the key below the label to use the displayed function. Press a function key once to go to the last page viewed or twice to go to its “home” page.
Hard Keys The “Hard” keys are the easy-touch, black, rounded keys with white lettering on the right side of the display. These keys include, NAV, NRST, INFO, SEL, MAP, Direct-To, and ENTER.
ENTER MAP D
NAV (Navigation) Press the NAV key to reach the navigation functions. Press twice to go to the “top” page.
NRST (Nearest Waypoint) The Nearest Waypoint (Emergency) mode displays the closest waypoints to your position.
INFO (Information) The Info function accesses supplementary information about a waypoint. Press INFO a second time to return to the previous display.
SEL (Select) The SELECT key activates editing or the selection of options. Editing is active on the items that flash on the display. Press SEL a second time to deactivate selection.
Introduction

MAP (Graphic Moving Map) The Map key starts the Moving Map function. The entire display is used as a graphic map display.
DIRECT-TO The DIRECT-TO key is used to define a direct course from your present position to a waypoint. Press once to select a waypoint. Press twice to enter an OBS desired track To or From the current active waypoint.
ENTER The ENTER key enters and saves the information flashing on the display. If the ENTER key is not pressed after editing, any changes made are not saved. In the GX60/65, the ENTER key flip/flops the Active and Standby frequencies.
“Smart” Keys The Apollo GX uses “smart” keys to provide custom
controls for specialized functions. Five small unlabeled keys are located below the display. The labels appear on the display and can change to give extra controls for the active function, such as in the MAP function. You can always press the NAV key to go back to the Navigation function and view the normal “smart” keys.
MSG (Message) Press the MSG key to reach the Message functions. The MSG annunciator will flash when a new message is provided. Press the MSG key a second time to return to the previous display after all new messages have been viewed. The MSG key will remain highlighted when a message remains.
DB (Database) The Database key provides access to the waypoint database.
FPL (Flight Plan) The Flight Plan key takes you to the flight planning function where you can create, edit, and control your flight plans.
Introduction

SYS (System Mode) Press the SYS key to reach the System mode functions. System mode is used to make system level adjustments and modify Nav function displays.
SKIP (Start-Up Option) Press the SKIP key during the start-up procedure to bypass the start-up tests. This is for emergencies as the IFR tests must be completed to allow IFR flight.
Map Function Smart Keys
The Moving Map function uses several “smart” keys to allow you to declutter the map, find waypoint information, and setup your map information.
Map Waypoint Keys APT, VOR, INT, NDB, & USR
The map waypoint “smart” keys are present when the Moving Map pages are displayed. Press the “smart” key to control the display of the waypoint type. There are three selections possible: waypoint identifier and location symbol, location symbol only, and off. Pressing the “smart” key subsequent times will control which selection is made. Map waypoint choices are: Airport (APT), VOR, NDB, Intersection (INT), and User (USR).
NDB
VOR
USR
INT
A solid, reversed waypoint type annunciator above the “smart” key means the waypoint identifier and location symbol will both be displayed.
A bold outline of the waypoint type annunciator will show only a symbol on the waypoint location.
A thin outline around the waypoint type means that it is turned off and no information for that waypoint type will be displayed on the map.
Waypoint LIST Key Each press of this key scrolls through the available “smart” keys.
Introduction

Waypoint SCAN Key When the SCAN key is active (highlighted) in the Moving Map display, turning the LARGE knob will move between the nearest airports. You can then press INFO to view information about that airport. In an emergency press DIRECT-TO and ENTER to fly direct to the highlighted airport. Press the SCAN key again to return the LARGE knob to normal operation.
Map Setup Keys The Map Setup page displays three “smart” keys that provide a short cut for customizing your moving map.
Map Orient:DTK
Map ref:Plane·
The Route Line “smart” key toggles between On and Off. See page 4 for more details.
The Map Orientation “smart” key toggles between Desired Track (DTK), Track, and North. See page 5 for more details.
The Map Reference “smart” key toggles between Plane and Destination (Dest) as the moving map center point. See page 6 for more details.

The Recall (RCL), Monitor (MON), Memorize (MEM), and FLIP/FLOP () keys are available in the GX60/65 after the COM soft key has been pressed.
ons Radio Mode Smart
COM (GX60/65) Press the COM key to operate the Communications radio functions.
Flip/Flop (GX60/65) Press the FLIP/FLOP key to switch between the active (left-most) and standby (right-most) frequency while in the Com function. You may use an optional external FLIP/FLOP key for the same operation as the front panel control. Switching between frequencies is disabled while you are transmitting or editing in any function.
RCL (Recall) (GX60/65) Press the RCL key to recall frequencies stored in the database.
MON (Monitor) (GX60/65) Press the MON key to listen to the Standby frequency. When the Active frequency receives a signal, the GX60 will automatically switch to the Active frequency.
MEM (Memorize) (GX60/65) Press the MEM key to store the current Standby frequency.
XIT (Exit) (GX60/65) The XIT key will appear on the far left of the display, in the MSG key position, if the COM key has been pressed to allow use of the radio during startup testing. Press the XIT key to return to the start-up sequence, or wait for test completion. The XIT key will disappear when testing is complete.

30 Reversible Flight Plans of up to 20 Legs with Automatic Sequencing 500 User-Defined Waypoints Nav Displays
Lat/Lon Bearing and Distance Ground Speed and Track Angle Desired Track and Distance Internal CDI Display 160 pixel wide by 80 pixel high electroluminescent display with moving map Automatic Display Intensity Control User-Selectable Nav Displays User-Definable Distance and Speed Settings:
nm and km (distance) knots Clock and Countdown Timer Auto/Manual Magnetic Variation Settings Direct-To Nav Function Parallel Track Nearest Waypoint Search Internal Database of Airports, VORs, NDBs, Intersections, Frequencies, Airport Info, and controlled and special use airspace
GPS Receiver Performance Specifications
8-Channel Parallel GPS Receiver Frequency 1575.42 MHz L1, C/A code Sensitivity (acquisition) -135 dBm Sensitivity (drop lock) -142 dBm Dynamic range > 20 dB Lat/Lon position accuracy
15 meters RMS accuracy 25 meters, SEP, without SA 100 meters 2 DRMS with SA Velocity 999 knots maximum Acceleration 4G maximum TTFF (time to first fix)
25 sec. typ. with current almanac, position, time, and ephemeris 55 seconds typical with current almanac, position, & time Reacquisition 2.5 seconds typical Position update interval 1 second typical Datum WGS-84
Apollo GX Features · Navigation Features

10 VDC to 40 VDC, reverse polarity protected Input current (GPS navigation input)
500 mA typical, 750 mA max at 13.75 VDC 250 mA typical, 375 mA max at 27.5 VDC Input current (comm input - GX60/65 only)
270 mA typical, 2A max at 13.75 VDC, receive 130 mA typical, 900 mA max at 27.5 VDC, receive 2.1A typical, 3.2A max at 13.75, transmit 1.0A typical, 1.4A max at 27.5 VDC, transmit Input power (GPS navigation input)
7 watts typical Input power (comm input - GX60/65 only)
3.7 watts typical, receive 28 watts typical, transmit
GX50 and GX60/65 Avionics Outputs
CDI L/R deviation ±150 mv full scale TO/OFF/FROM flag ±250 mv, TO/FROM indication Nav valid flag +300 mv for valid indication Nav superflag 400 ma source VDI up/down ±150 mv VDI valid flag +300 mv VDI superflag 400 ma source Annunciators
MSG (message) PTK (parallel track) OBS/HLD (waypoint sequencing hold) GX50/60 only APPRCH (approach enabled)GX50/60 only ACTIVE (approach active) GX50/60 only
CDI L/R deviation ±150 mv full scale TO/OFF/FROM flag ±250 mv, TO/FROM indication Nav valid flag +300 mv for valid indication Annunciators
MSG (message) PTK (parallel track)
Serial Frequency flip/flop (GX60/65 only) Waypoint Sequence (GX50/60 only)

2 RS-232 for GX50/60/65 1 RS-232 for GX55
Height: 2.0 inches (5.08 cm) Width: 6.25 inches (15.88 cm) Depth: 11.125 inches (28.26 cm) behind panel, including mounting frame and connectors Weight (with mounting frame):
GX50 and GX55 - 2.6 pounds (1.179 kg) GX60/65 - 3.1 pounds (1.409 kg)
Operating temperature -20ºC to +55ºC Storage temperature -55ºC to +85ºC Temperature variation 2ºC per minute Humidity 95% at 50ºC for 6 hrs (2 day cycle) Maximum altitude 55,000 feet Cooling Not required
VHF Comm Features (GX60/65)
760 channels Frequency range of 118.000 to 136.975 MHz Active and standby frequency display Transmit status indicator Stuck mic time-out Frequency monitor function - listen to Standby frequency
while monitoring Active frequency for any activity Weather channels - National Weather Service channels
(not available in all databases) Built-in intercom function Frequency memory and recall functions
from navigation data base ten last used ten user stored Two microphone inputs 12 watt audio amplifier

VHF Comm Receiver Performance Specifications (GX60/65)
Class D Frequency range - 118.000 to 136.975 MHz, 760 channels Sensitivity
1 microvolt (2 microvolt hard) for 6 dB S+N/N 30% modulation at 1000 Hz Selectivity
12 watts into 4 ohms, 8 watts into 8 ohms Headphone audio output level
280 mW into 100 ohms, 120 mW into 500 ohms Distortion -
VHF Comm Transceiver Performance Specifications (GX60/65)
Class 4 Output Power
8 watts minimum carrier at > 12 VDC 6 watts minimum at 10 VDC (transmit is locked out below 9 VDC input) Modulation capability
85% with 100 mv to 1000 mv rms microphone input at 1000 Hz Duty cycle 100% Stuck mic time out
35 second time-out, reverts to receive
TSO C129A A1 GX55
TSO C129 A2 GX60
TSO C129A A1 TSO C128 TSO C37d TSO C38d GX65
TSO C129A A2 TSO C128 TSO C37d TSO C38d
Features and specifications subject to change without notice.
Apollo GX Features · TSO Authorizations

This section explains how to get started using your Apollo GX. Information in this section explains how to:
Select a waypoint
Find a Nearest Waypoint
Fly Direct-To a waypoint
Create a flight plan
Activate a flight plan
Use the Moving Map It is necessary to enter a seed position and the current time the first time you turn the unit on. This should have been done when your unit was installed. So, you won’t have to set it again unless the unit has been moved several hundred miles with the power off.
Power On Turn the Power knob clockwise to switch the unit on. The startup screen, testing, position, and database information shows on the display for several seconds and then will go into the Navigation function.
You can search for a waypoint character by character, sort through the database by selecting the first few characters of the identifier to simplify the search, or look at every waypoint in order. You can search for waypoints by identifier or the city/facility name.
Finding a waypoint by name 1. Press the DB smart key. Turn the LARGE knob to display the Access Database page. Press ENTER.

AIRPORT HIO PORTLAND city OR USA
AIRPORT HIO PORTLAND city OR USA
Sorting waypoints by selected characters 1. Press the DB smart key. Turn the LARGE knob to display the Access Database page. Press ENTER.
AIRPORT 5VD KADOKA city SD USA
Getting Started

AIRPORT 09C KALAMAZOO city dup MI USA
AIRPORT 09C KALAMAZOO city dup MI USA
AIRPORT FCA KALISPELL city dup MT USA
Looking at all waypoints in a database 1. Press the DB smart key. Turn the LARGE knob to display the Access Database page. Press ENTER.
Getting Started

Duplicate Identifier, City, or Facility Names While performing Waypoint Identifier selection, you may see the word “dup” on the bottom line. This means that there is more than one waypoint for the displayed city or facility name. The same technique described above can be used to search for duplicate city and facility names.
The GX-series contains a wealth of information in its database. Pressing the INFO key will access the information about the destination (TO), or displayed, waypoint.
HIO AIRPORT PORTLAND city OR USA
UNIC 123.00 TWR 119.30
HIO 12 /30 6600ft Hard ILS Lighted
Getting Started · Waypoint Information

Your Apollo GX can store up to 500 user-defined waypoints in the USER database. The waypoint can be created by providing a Lat/Lon position or by a Radial and Distance from a reference waypoint. Then, you can give your waypoint a name and even include a runway length. You can use up to six characters with upper case letters, numbers, or a space for the name. You can also enter a runway length from 0 to 9999 ft. You are not allowed to use a USER waypoint as the Radial and Distance reference waypoint. This example will create a Lat/Lon-based USER waypoint. For more details on waypoints, see the Waypoint Database section on page 1.
by Lat/Lon Press ENTER
#001 USER 43°13.21N Rwlen 122°54.89W 000’
Getting Started · Storing a Waypoint · Create User Wpt

When you press the NRST key, your Apollo GX will search for the nearest 20 waypoints within 600 nm for each waypoint type. You can also be selective about the runway length, lighting, and surface type. See Setting Runway Limits on page 12.
Near 1 to PPos SLE AIRPORT Brg 352°½ 5.4nm
Near 1 to PPos UBG VOR Brg 344°½ 26.6nm
Near 2 to PPos CVO VOR Brg 189°² 27.5nm
Getting Started · Finding a · Nearest Waypoint

Pressing DIRECT-TO allows you to quickly make changes to your TO waypoint. When you press DIRECT-TO, the default waypoint shown will be the current TO waypoint in the Nav or Flight Plan functions or the waypoint displayed in the Database or Info functions. See page 31 for more details.
VOR CVO SALEM CITY OR USA
ete aHIO 00:12 “ 0.002 Brg 346 35.2nm·
Note See Direct-To Entry Options on page 8 in the System Functions chapter for details. When the option is set to “May Clear,” your active flight plan is deleted when you use Direct-To for flying to a new destination. If your new Direct-To waypoint is in the active flight plan, the flight plan is not deleted. When the option is set to “Never Clears,” the Direct-To waypoint is inserted into your active flight plan before the current TO waypoint. “May Clear” is the default setting.
Getting Started · Flying Direct-To a · Waypoint

Create a Flight Plan
You can create up to 30 flight plans with up to 20 legs each. A flight plan name can have up to eight characters using upper case letters, numbers, or a space.
Press SEL to Create a New Flight Plan
to Ins Wpts or SEL for Options

Ins? to 1 ___° nm
SLE to Ins? 1 ___° nm
Select a flight plan from your stored plans. Activating a flight plan copies it into the Active page.

Using the Moving Map
The Moving Map gives you a graphic presentation of your flight progress. You can select the type of waypoint displayed, a route line, ATC ring, airspace setup, type of airspace displayed, and map orientation. See the Moving Map section on page 1 for more details.
Viewing the Moving Map 1. Press MAP. Turn the LARGE knob to view the map and nav information, full screen map, and map setup displays.
Distance to the TO Waypoint
aPDX 44.2
Bearing to the TO Waypoint
0.01> 30
Cross Track Error Distance & Direction
Setting Up the Moving Map 1. Press MAP. Turn the LARGE knob to the Map Setup page. Note the diamond (·) in the lower right corner of the display. This diamond means there are more pages for a function. Turn the SMALL knob to view the other Map Setup pages.
Route Line:Off Map Orient:Track Map Ref:Plane ·

Airspace Types (B, C, MOA,
Route Line, Map Orient,
Search & Rescue Setup*
Map plus Nav & Comm Info
Press MAP Moving Map (MAP)
Symbol & ID Setup
Search & Rescue Map
Map plus Nav Info
(diamond shown).
pages shown. Turn
knob to view the
Comm function, ENTER saves the Standby frequency.
Press SEL to edit information or to select options.
Press ENTER to enter and save information. In the
Press Direct-To to define a direct course from your
Press NRST Nearest Waypoint (NRST)
present position to a selected waypoint.
NDB
INT
SUA
Press NAV Navigation (NAV)
(SEL)
( D )

Press RCL to recall stored frequencies
Turn the LARGE Knob to view
Press to toggle Active & Standby
Turn the SMALL Knob to view
frequencies for selected type
Turn LARGE Knob to change MHz
Turn SMALL Knob to change kHz
Press MEM to memorize Standby
Press MON to monitor Standby
Press SYS. Turn LARGE Knob, then press ENTER.
FPL #1
Satellites Used for Fix
GPS Date & Time
Create WPT by Grid
Model, SW Ver, S/N

This section explores the navigation function and describes the powerful features it contains.
The navigation function is always active. When you use other functions, the navigation function continues to run “in the background” calculating your present position, navigating your programmed route (if active), and alerting you to events or conditions important to navigation. When you finish using other functions and return to the navigation function, the last navigation display used is shown.
While you navigate, the Apollo GX gives you information in the Navigation function displays. The navigation information displays and sequencing rate are user-programmable. See the Nav info section of the System Functions chapter (see page 1) for your options. The LARGE knob will select the higher level Nav functions: Nav pages, Parallel Track Offset, GPS Position, Countdown Timer, and the FROM/TO/NEXT Waypoints. The SMALL knob will look at the pages available for each function; a diamond (·) will be shown on the lower, right side of the display if more pages are available.
The Nav Home Page is a default page that is the first page available in the Navigation function. The Nav Home Page is not customizable. The information in the Home Page shows the Destination Waypoint identifier, Estimated Time En Route, CDI, Bearing, and Range (distance) to the destination waypoint.
Ete aEUG 00:22 1.10 “¼¸ Brg 082½ 74nmY
Turn the SMALL knob to view the other available Navigation displays.

TAE = Difference between Track
Bearing = Direction to waypoint
Course = Desired Track between
Desired Track = Course direction
Track = Direction the aircraft is going
DTK
Heading = Direction the aircraft is
Distance Off Track or Cross Track Deviation
WPT
Navigation Terms and Abbreviations
Autonav The Autonav feature lets you select certain Nav display choices and have them rotate in sequence displaying each one from one to nine seconds. The selection of displays and sequencing time is performed in the Nav Info part of the System Functions (see page 1).
Ete aEUG 00:22 1.10 “¼¸ Brg 082½ 74nmY

The Relative Bearing Indicator is an arrow next to the Bearing value that indicates an approximate bearing to a waypoint or airspace relative to the aircraft’s current track when your current ground speed is more than 5 knots. The following illustration describes the bearing range for each arrow.
Near 1 to PPos PDX AIRPORT Brg 010½ 39.7nm·
Nav Pages The Apollo GX provides a wide variety of navigation information. This information is provided on a number of displays that you can view by turning the LARGE knob. Some displays have a diamond in the lower right corner; turn the SMALL knob to view more related information.
Estimated Time Enroute Label
Estimated Time Enroute Value
"Diamond" indicates more pages can be selected with the Small knob. ete aEUG 00:16
Brg 173 45.5nm
·
Range to Destination Waypoint from your Present Position

Estimated Time En Route (Ete) ETE is to the current TO (destination) waypoint from your present position based on the current ground speed. The units shown are in hours and minutes, 00:00 to 99:59, and in seconds when less than one hour is displayed. If the ground speed is less than or equal to 5 knots, the GPS receiver does not have a valid position, or there is no TO waypoint, the ETE value will be shown as dashes. If there is no TO waypoint, the TO identifier location will be replaced by dashes.
Bearing (Brg) Bearing is the angle from your present position to the TO waypoint. Bearing is shown from 0 to 359 degrees in one degree increments. Bearing is computed using the magnetic variation at the Present Position. The Bearing value will be dashed if the FROM or TO waypoints are blank or the GPS receiver does not have a valid position.
ete aEUG 00:16
“¼º
“¼º
Brg 173 45.5nm
·
173 Trk172
Bearing listed in the direction you are off-course (value will switch to either side as required)
Range (Rge) The distance from your present position to the TO waypoint. Units can be set as either nautical miles or kilometers in the Nav Info section of the System functions (see page 6). Nautical mile units are 0.00 to 9.00 nm in 0.01 nm increments, 10.0 to 99.9 nm in 0.1 nm increments, and 100 to 9999 nm in 1 nm increments. Kilometer units are 0.00 to 99.99 km in 0.01 km increments, 100.0 to 999.9 km in 0.1 km increments, and 1000 to 9999 km in 1 km increments. The Range value will be dashed if the FROM or TO waypoints are blank or the GPS receiver does not have a valid position.

Course Deviation Indicator (CDI) and Distance Off Track The triangle symbol (“) referenced to a bar graph shows your position relative to being on-course. When the bar graph is to the right of the triangle, you must fly right to return on-course. In the example below, the bar graph indicates you are off-course to the right. Fly the aircraft in the direction of the bar graph (left) to return on-course.
ete aSLE 00:37 #### “ 4.005 Brg 173¯ 42.4nm
CDI Sensitivity = 0.3
CDI Sensitivity = 1.0
CDI Sensitivity = 5.0
nm each 7 = 0.01 nm each $ = 0.05 nm each H = 0.24 nm each 6 = 0.04 nm each z = 0.14 nm each B = 0.71 nm “ ››››››› (full scale) = 0.3 nm
“ ¼¼¼¼¼¼¼ (full scale) = 1.0 nm
“ ¥¥¥¥¥¥¥ (full scale) = 5.0 nm
A single dot thickness bar indicates that CDI sensitivity is set to 0.3 nm full scale per side. The two dot bar indicates a sensitivity of 1.0 nm full scale per side. The three dot bar indicates a sensitivity of 5.0 nm full scale per side. The manual sensitivity of the CDI may be set to 0.3, 1.0, or 5.0 nm full scale per side.
The number shown on the edge of the display opposite from the triangle symbol shows the distance off track. The numbered values of Cross Track Error are in the direction you are off course. If the numbers are on the left side, fly right to return on course. The displayed value ranges are: 0.000 to 0.999 nm with 0.001 nm resolution, 1.0 to 9.99 nm with 0.01 nm resolution, and 10.0 to 99.9 nm with 0.1 nm resolution.
ete aSLE 00:37 0.006 “ Brg 173 42.4nm
Navigation Basics · nm · nm

If the GPS sensor is not sending a valid position, or the current TO waypoint is blank, the CDI will display “—Nav Flagged—”.
TO/FROM Indicator The triangle symbol is also used as a TO-FROM indicator. When the triangle is facing up, you are on the “TO” side of the destination waypoint. When the triangle is facing upside down, you are on the “FROM” side of the destination waypoint.
TO side of destination waypoint
From side of destination waypoint “
Desired Track (Dtk) Desired Track is the initial course angle between the FROM and TO waypoints referenced to the magnetic variation at the current FROM waypoint. Desired Track is shown from 0 to 359 degrees in one degree increments and is updated in reference to your present position. The Leg distance shown (42.4 nm) is the current FROM/TO distance. DTK varies with Turn Anticipation (page 36) and DME Arcs (page 26).
ete aSLE 00:37 0.006 “ Dtk 173 42.4nm
Leg (FROM-TO) Distance The distance from current FROM waypoint to the current TO waypoint is shown as a value on the right side of the Desired Track page, but does not show any label. In this example, the leg (FROM-TO) distance is 42.4 nm. The nautical mile units are 0.00 to 9.99 nm at 0.01 nm resolution, 10.0 to 99.9 nm at 0.1 nm resolution, and 100 to 9999 nm at one nm resolution. Kilometer units are 0.00 to 99.99 km at 0.01 km

resolution, 100.0 to 999.9 km at 0.1 km resolution, and 1000 to 9999 km at 1 km resolution. See page 6 for details on changing units of measurement.
Track (Trk) Angle Track Angle is the angle of your actual direction of travel. Track is shown as a positive value from 0 to 359 degrees in one degree increments. Track is computed using the magnetic variation at the Present Position. The Track value will be dashed if the FROM or TO waypoints are blank, if the GPS receiver does not have a valid position, or if ground speed is less than 5 knots.
ete aSLE 00:37 0.006 “ Trk 175 Tae 002R
Track Angle Error (Tae) Track Angle Error is the difference between the Desired Track and Track Angle (Dtk - Trk). Track Angle Error is shown from 0 to 359 degrees in one degree increments. Track Angle Error is computed using the magnetic variation at the Present Position. The Track Angle Error value will be dashed if the FROM or TO waypoints are blank, if the GPS receiver does not have a valid position, or if ground speed is less than 5 knots. A letter ® or L) will show the direction of the error in relation to track angle.
TRK TAE = Difference between Track
Track Angle Error (TAE)
Desired Track = Course direction
Track = Direction the aircraft is going
Ground Speed (GS) Ground Speed is the measure of your progress over the ground, not airspeed. Ground Speed units are from 0 to 999 knots in 1 knot increments. The Ground Speed value will be replaced with dashes if the speed is less than 5 knots, there is no valid GPS position, or the TO waypoint is blank. See page 6 for details on changing units of measurement.

ete aSLE 00:37 0.006 “ Ft01:23 137kts
Minimum Safe Altitude (MSA) MSA is calculated by taking the Maximum Elevation Figure (MEF) from the sectional chart grid that corresponds to your current position. In areas below 3,000 feet, 1,000 feet is added. In areas above 3,000 feet, 2,000 feet is added. In the example below, the current aircraft would be considered to be at 7,000 feet. If you are within 5 nm of another grid with a higher MEF, the higher MEF will be used. The MEF on the sectional chart is derived by taking the altitude of the highest obstruction within the grid, rounded up to the next 100 feet, and adding 300 feet. For example, if the highest obstruction is 4,728 feet, the MEF would show as 5,100 feet.
5 nm Buffer MEFs
14 8 5 2
eta aSLE 01:23 MinSafeA 7200’ EnrtSafeA 16800’
Minimum En Route Safe Altitude (MESA) Minimum En Route Safe Altitude is the highest MSA for every point between the aircraft present position and the “TO” waypoint with a 5 nm buffer around the course. The value will be replaced with dashes if there is no valid GPS position, the TO waypoint is blank, or the current position is outside of the
Navigation Basics · TO Waypoint · FROM Waypoint

database coverage area. In the example shown above, the MESA for the present position of the aircraft would be 16,800 ft. The mountainous terrain would add a 2,000 ft. buffer to the 14,800 ft. Maximum Elevation figure indicated from the sectional chart.
Flight Time Flight Time shows the elapsed time in hours and minutes (00:00 to 99:59) from departure. If the Flight Timer is not started the value will be replaced with dashes. The Flight Timer Trigger options are set in the System Functions (see page 8).
Time UTC Time is displayed using the 24 hour clock based on Universal Coordinated Time. Units are hours and minutes (00:00 to 23:59).
Estimated Time of Arrival (ETA) The ETA is the arrival time at the current TO waypoint at the current Ground Speed from the present position. The TO waypoint is displayed. Units are hours and minutes (00:00 to 23:59) based on the UTC 24 hour clock. The values will be replaced with dashes if the speed is less than 5 knots, there is no valid GPS position, or the TO and/or destination waypoints are blank.
eta aEUG 09:11
An important safety feature of the GX is its ability to locate waypoints and airspaces closest to your position. Should you have to land quickly, you can use this feature to locate a nearby waypoint, assign it as a destination, and quickly navigate to it. You can also insert waypoints into an active flight plan. Besides the nearest waypoints to your present position, as an aid in flight planning, you can also select a reference waypoint from the database and search for waypoints near to it. You can set up the Nearest Waypoint Search function to filter for certain

airport types you select, such as: runway length, lighting, and surface type. Press INFO while viewing a Nearest waypoint for more information about that waypoint.
Starting Nearest Waypoint & Airspace Search 1. Press the NRST key. Turn the LARGE knob to display the waypoint type or options: Airport, VOR, NDB, Intersection (INT), User (USER), Choose Reference Waypoint, Runway Limits, and Special Use Airspace.
Near 1 to PPos SLE AIRPORT Brg 352°½ 2.4nm
Near 12 to PPos CVO AIRPORT Brg 188°² 27.6nm
Searching Around a Reference Waypoint Use this function to search for the 20 nearest waypoints of each type (including airspaces) within 600 miles of a reference waypoint selected from the database. This can be used as an aid to flight planning for waypoints far away from your present position.
Choose Wpt to Search Around
Navigation Basics · Press ENT

VOR PDX PORTLAND facil OR USA
AIRPORT SLE SALEM city OR USA
Near 1 to SLE SLE AIRPORT Brg 110° 0.5nm
Navigation Basics

Setting Runway Limits for Nearest Waypoints Narrow the type of airports that you will accept by choosing the runway length, lighting, and surface type. The Runway Limits selection also controls the airports that are displayed in the Map function.
Runway Limits HARD/SOFT/WATER Ft:0 Lit:No
2. Press SEL. The runway length value will flash. Turn the SMALL knob to select the minimum runway length you want considered. Choosing a length of 0 feet means you will accept any runway length. Choosing a runway length, for instance, of 5,000 feet, will not show an available airport with a runway length less than 5,000 feet either for a Nearest Waypoint or as an airport icon on the Map display. Note that a waypoint with a runway of 0 length will not appear on either the nearest list, or on the map, if a length is set for the runway limit that is greater than 0. User Waypoints will show.
Runway Limits HARD/SOFT/WATER Ft:3500 Lit:No
Runway Limits HARD/SOFT/WATER Ft:3500 Lit:Yes
Navigation Basics

HARD/SOFT Ft:3500 Lit:Yes
When searching around your present position, the first ten airspaces within 100 miles are displayed. While searching for airspaces, the keys and knobs are disabled and the following display will appear.
for Airspaces...
The information for airspaces includes: name, position in the list (1-10), type, and proximity. Proximity is indicated as either: Soon, Outside, Inside, Above, Below, or Close. Criteria for airspace searches is set in the System functions (see page 12). For proximity definitions, see page 3.
“MSL” stands for feet above Mean Sea Level. “AGL” stands for feet Above Ground Level.
KANSAS CITY 1 Class B SOON Brg 210° ½ 7.1nm

The Nearest Airspace list is updated periodically as your aircraft moves and the following display may appear.
Airspaces Please Wait...
Altitude Assist provides guidance for your vertical navigation needs. Altitude Assist features require the system to include either a Fuel/Air Data Sensor (F/ADS) or an altitude encoder sensor.
The features available in the Altitude Assist function are:
Set Local Altimeter value
View Encoder Altitude value
Set and activate Auto Descent Values (Ending Altitude, Distance from the Destination Waypoint, Descent Rate, and estimated speed)
Set and activate Hold Altitude and Buffer

In the Nav function, turn the LARGE knob to view the Altitude Assist page. The diamond in the corner notes that turning the SMALL knob will show the Encoder Altitude, Auto Descent, End Altitude, and Hold Altitude, and Buffer values.
Altitude Assist Local Altimeter Setting 29.92" ·
Setting the Local Altimeter Value 1. While viewing the Altitude Assist page, press SEL. The setting value will flash. The default barometric pressure setting is 29.92".
If an Air/Data Sensor is installed and provides corrected baro-altitude, barometric altitude will be displayed instead of the altimeter setting.
Altitude Assist Local Altimeter Setting 29.92 ·
Altitude Assist Local Altimeter Setting 29.92" ·
Encoder Altitude The altitude information received from the altitude sensor is displayed on this page if an altitude encoder or F/ADC is installed. You cannot change these values.
Navigation Basics · Encoder Altitude · 2036ft

Setting Hold Altitude and Buffer The Hold Altitude is an altitude where you want to remain. The Buffer is the tolerance or range in altitude that you can move in vertically before a warning message is generated.
Hold Alt 5650ft Buffer 150 ft ENT to Hold Alt
Hold Alt 4550ft Buffer 150 ft ENT to Hold Alt
Hold Rdy 4550ft Buffer 100ft

Auto Descent The Auto Descent feature allows you to input a desired End Altitude, an Offset Distance from a desired Auto Descent Waypoint from the Active flight plan, a desired Feet per Minute Descent rate, and an expected Ground speed. It then automatically calculates the distance remaining in your Active flight plan to the desired Auto Descent Waypoint and, based on the calculated glide path angle, your present altitude, and the altitude you are descending to, alerts you with a message when you should begin and end your descent. A Nav item field displays information indicating how much time remains before you should begin Auto Descent, and once Auto Descent begins, whether you are above or below your intended Glide Path. Glide Path data may also be output to an optional Vertical Deviation or HSI Glide Slope Indicator.
Auto Descent Starting Point
Auto Descent Offset Distance
Each time you begin to edit the Auto Descent values, the End Altitude is automatically reset to 1,000 feet over the altitude of the desired Auto Descent Waypoint, if the waypoint is an airport. Otherwise, the End Altitude automatically resets to 2,000 feet. In addition, the default Auto Descent Waypoint is automatically updated, as long as Auto Descent is OFF, to the current TO waypoint each time a waypoint sequence occurs.

Set up your Auto-Descent by selecting:
Distance from destination waypoint (0 - 99 nm) or Offset Distance
Ending altitude (-1,500 - 50,000’ in 50’ steps)
Descent rate (100 - 5,000’/min in 10’/min steps)
Estimated ground speed (50 - 600 kts) 1. While viewing either the Auto-Descent or End Alt page in the Altitude Assist function, press SEL. The Offset Distance value will flash. Turn the SMALL knob to change the Descent Offset Distance value.
End 5nm before PDX at 1027’ 500’/min 200kts
Navigation Basics

This function allows you to create a parallel course offset to the left or right from your current flight plan from 0.1 to 20.0 nm. You must have FROM and TO waypoints defined. Parallel Track cannot be activated if you set a course using Direct-To. Transitions between future flight plan legs cannot have turns greater than 120 degrees. You select to place Parallel Track “In Use” or to put it on “Standby,” choose Left or Right of the current course, and the offset distance. The PTK annunciator (if installed) will turn on when Parallel Track is enabled.
BRG
TRK
DTK
FROM
WPT
When Parallel Track is selected, the course line drawn on the Map pages will show the parallel course. If the Hold function is used when Parallel Track is selected, the Hold waypoint will be the phantom waypoint on the parallel offset, not the actual waypoint. Using Direct-To, loading an approach, or editing your flight plan will automatically cancel Parallel Track. A series of turns, even if less than 120°, is not allowed if the “inside” parallel tracks would overlap.

Navigation Basics

ete pCVO 00:22 0.034 “ Brg 186 46.1nm·
GPS Position The GPS Position page shows the calculated Latitude and Longitude, as well as its Position Dilution of Precision (PDOP). The PDOP value, shown below “PDOP,” is based on the geometry of the satellites used in the position solution. A lower number is a better value than a large one. A PDOP value of 3 will provide a more reliable position fix than a value of 7.
In the Navigation function, turn the LARGE knob to display the GPS Position page. The PDOP value is shown in the lower, right corner (1.9 is shown here).
GPS Position 44°10.11N PDOP 123015.84W 1.9
Navigation Basics

The Countdown Timer allows you to set a timer that will alert you when it expires with a flashing MSG annunciator. The maximum time is 99:59:59 (hours, minutes, seconds). The default time on power up is the previous time that was entered. The factory default time is 00:03:00 (3 minutes). You can stop the timer by pressing SEL twice while viewing the Countdown Timer page.
00:03:00
00:03:00
01:03:00

Arc Assist The Arc Assist function will help you to navigate along an arc. In the GX50/60, Arc Assist will help you fly approaches with DME Arcs. Arc Assist can be used as a user-defined arc to avoid special use airspaces, or for conducting aerial searches using increasingly larger circles. The Arc Assist page shows the direction of the arc (left or right), the reference waypoint identifier, the desired track for the arc, and the distance to the reference waypoint.
The Arc Assist reference waypoint defaults to the nearest VOR unless you have already selected one. Press ENTER to accept the displayed reference waypoint. Press SEL to choose another reference waypoint.

VOR CVO CORVALLIS facil OR USA
Other Uses for Arc Assist You can select the reference waypoint for the Arc Assist feature and it can be used at any time, not just during approach or terminal operations. It can also be used for difficult operations such as conducting an over water search. By establishing a user waypoint at the center of such a search area and selecting that waypoint as a DME Arc reference point, you can fly circles about that waypoint at known distances. By gradually increasing the arc distance each time you pass a specific radial, you can expand the search area. The Arc Assist feature of the Apollo GX can make this much easier.
Navigation Basics

This page shows the cumulative distance from your current position to each waypoint in the active flight plan starting with the active leg. Turn the SMALL knob to view the next set of waypoints in your active flight plan. The waypoint type is shown to the left of the identifier. The allowable waypoint types are: Airport (a), Intersection (i), NDB (n), and VOR (v). The waypoint type symbol will not be shown if one of the following occurs: the waypoint identifier is unknown, it is an approach waypoint that is not one of the four used types, it is a User waypoint, the waypoint is not recognized by the current data card’s database, or the data card has been removed.
aSLE nm aPDX 43nm aSEA 154nm
This page displays the cumulative time in hours and minutes from your current position to each waypoint in the active flight plan, starting with the active leg. Turn the SMALL knob to view the next page of waypoints. The time will not be shown for the same reasons as in the Waypoint Distance page.
aSLE ete--:-- aPDX ete00:25 aSEA ete01:32
This page displays the ETA for each waypoint in your active flight plan from your current position, starting with the active leg. Turn the SMALL knob to view the next page of waypoints. The time will not be shown for the same reasons as in the Waypoint Distance page, if the ground speed is zero, or if 3-D positioning is lost.
aSLE eta--:-- aPDX eta12:15 aSEA eta13:32

The FROM/TO/NEXT Waypoint allows you to view and/or edit a three waypoint mini-flight plan, or view two legs of your flight plan, while within the Nav function. These waypoints are like a three waypoint window into your Active Flight Plan. Changes to the FROM/TO/NEXT page change the Active Flight Plan, and vice versa. You may also Hold (sequencing suspended) or enable the TO waypoint.
WPT
TO WPT
FROM
WPT
From SLE arpt To UBG vor Next HIO arpt
Creating FROM/TO/NEXT Waypoints A - Set the FROM Waypoint
From To Next

From Ins? To Next
AIRPORT AAF APALACHIOCOLA city FL USA
AIRPORT EAA EAGLE city AK USA
AIRPORT EUF EUFAULA city AL USA
Navigation Basics

AIRPORT EUG EUGENE city OR USA
From EUG arpt To Next
B - Set the TO Waypoint
From EUG arpt To Ins? Next
From EUG arpt To SLE Next
Navigation Basics

C - Set the NEXT Waypoint
From EUG arpt To SLE Next Ins?
From EUG arpt To SLE arpt Next HIO arpt
D - Editing FROM/TO/NEXT Waypoints
From EUG arpt To SLE arpt Next Chg? arpt
From EUG arpt To Chg? arpt Next HIO arpt
Navigation Basics

Placing the TO Waypoint on Hold 1. Press SEL and move to the TO designation with the LARGE knob. You can also place the TO waypoint on hold by pressing the external WPT SEQ (or GPS/SEQ) button, when it is installed. You can also place a waypoint on Hold in the Flight Plan or FROM/TO/NEXT functions. The HOLD annunciator will light when it is installed to indicate that automatic waypoint sequencing is suspended.
From EUG arpt Hold?SLE arpt Next HIO arpt
From EUG arpt To? SLE arpt Next HIO arpt
From EUG arpt Hold SLE arpt Next HIO arpt
Reverse the operation to return to normal sequencing.
Navigation Basics

Pressing the DIRECT-TO key sets your present position as the FROM location. When using the Direct-To function, the FROM waypoint identifier is overwritten with the word “Direct.” If you remove the Direct-To position with the Del? option, the old FROM waypoint is returned to that position. If you edit the FROM position, Direct-To navigation will be replaced by the new entered waypoint.
FROM
WPT
Direct-To Defaults When you press DIRECT-TO, the default waypoint shown will be the current TO waypoint in the Nav or Flight Plan functions or the waypoint displayed in the Database or Info functions.
Function DIRECT-TO Waypoint Default
Nav Current TO waypoint Database Displayed waypoint Flight Plan Displayed leg TO waypoint Info Displayed waypoint
You can always select a different Direct-To waypoint, but the default is a useful starting point. While viewing the default waypoint, press DIRECT-TO and then ENTER to navigate directly to that waypoint.

Direct-To Operation 1. Press the DIRECT-TO key. The waypoint type will flash.
AIRPORT HIO PORTLAND city OR USA
AIRPORT MMV MC MINNVILLE city OR USA
The following three examples provide some of the more common ways that you can use the powerful Direct-To function.
Center the CDI After changing your course to avoid weather, an obstacle, or being directed, you may need to reset your course to center your CDI to continue navigating to your intended TO waypoint.
SLE
CDI EUG CDI

AIRPORT SLE SALEM city OR USA
Enter a New Waypoint into a Flight Plan While on a flight plan, you may want to temporarily go to a new waypoint to look at something or you may be directed by ATC. By using Direct-To, you can add this new waypoint into your existing flight plan. This way your flight plan is essentially unchanged, but you were still able to react quickly to new conditions.
Before Adding Direct-To Waypoint
After Adding Direct-To Waypoint
DLS
HIO
DLS
MMV
SLE
SLE

SLE to HIO 1** 345° 37.8nm arpt arpt
AIRPORT MMV MC MINNVILLE city OR USA
ete aMMV 00:20 0.011 “ Brg 321 15.6nm·
1** 321° 16.5nm —— arpt
MMV to HIO 2* 003° 22.2nm arpt arpt
Navigation Basics · direct to MMV

Direct-To OBS Pressing the DIRECT-TO key twice starts the OBS
desired track editor. OBS Desired Track allows entry of a desired track to or from the current TO waypoint. The current desired track in the navigation pages will be replaced by the OBS Desired Track value entered. You may also select the reference waypoint from your active flight plan. Waypoint sequencing is normally set as manual. When an approach is enabled, you may select either manual or automatic. You may wish to select manual sequencing so you may disable sequencing if you will be in a holding pattern that will cause you to continually cross the TO waypoint.
When your GX is configured to receive information from the SL30 Nav/Comm, the OBS Desired Track field is coupled to your HSI/CDI. Your HSI/CDI is being read by the SL30 at the same time. Rotating the control on your HSI/CDI will update the OBS Desired Track on your Apollo GX. You can override the HSI/CDI input to your Apollo GX by using the concentric knobs of the GX as described below.
Navigation Basics

The Apollo GX will provide information for you to smoothly transition from one flight plan leg to another. Turns are drawn on the moving map. You will receive a message about ten seconds before the turn. The message will count down to the beginning of the turn. The message shown below indicates that you are arriving at the SLE waypoint, the next leg desired track is 93°, and you should start your turn in about nine seconds.
Standard Turn Operation While you are in the turn, the desired track and cross track are determined based on the turn. Turns are made at three degrees per second if the ground speed is under 250 knots. If ground speed is greater than 250 knots, the turn rate is set at 1.5 degrees per second.
MMV
44S
SLE 6S4
7S5
If turn angle is greater than 120º, the turn will start well before reaching the waypoint
Turn anticipation is not shown if the end of the turn extends beyond the beginning of the next anticipated turn. That is, if the two waypoints are too close, turn anticipation will not be shown. Turn anticipation curves are only drawn when the turn is greater than 5°. If the turn is greater than 120°, the Apollo GX will generate a step turn message prior to the waypoint.

Turn anticipation will not be available when sequencing is on Hold; for the MAP or MAHP of an approach; or for the “flyover” waypoints in an approach.
Wind and Turn Anticipation The graphic Turn Anticipation curve drawn on the map display is based on your current ground speed. Once you enter the turn, the graphic curve is no longer updated. You may need to increase or decrease your standard rate turn to compensate for wind. If your installation includes a GPSS autopilot interface, the Apollo GX will monitor your progress throughout the turn and send corrections to the autopilot. Wind conditions requiring steeper than maximum bank angles may result in overshooting the new course line.
GPSS GPS Steering (GPSS) information is provided by your Apollo GX when setup with a properly installed autopilot. An autopilot guided by information from your Apollo GX will be more accurate, faster responding, and smoother than using a CDI. GPSS works with the Flight Plan and Turn Anticipation features to have your avionic equipment do more of the work for you.
Standard GPSS Operation Operating your Apollo GX with an autopilot is simple:
Navigation Basics

Approach GPSS Operation When the autopilot is directed by GPSS, there are few considerations when flying an approach.
GPSS information will not be provided after you pass the MAP. You need to follow the directions published on the approach plate.
When directed to the MAHP, use the Direct-To function. GPSS information will now once again be provided to the autopilot.
Certain waypoints within an approach may be coded as “Fly-over” waypoints. Fly-over waypoints must be overflown before starting your turn to the next waypoint. A turn anticipation curve will not be drawn for these Fly-over waypoints. The GPSS information from your Apollo GX will handle this automatically.
GPSS Rules There a few rules for providing valid GPSS information to your autopilot. Your autopilot should indicate when GPSS information is valid/invalid. Refer to your autopilot operating instructions for details.
Your ground speed must be more than 5 kts
You are navigating to a waypoint (flight plan or direct-to)
You are on the TO side of the waypoint
You are not executing Missed Approach procedures
Horizontal bank output from the Apollo GX to the autopilot is limited to 30° or less
Turn rate is 3°/sec at speeds less than 250 kts Turn rate is 1.5°/sec at speeds greater than 250 kts
Navigation Basics · Apollo GX Information · Autopilot Information

Tuned Station When your Apollo GX is connected to and configured
to communicate with an Apollo SL30 Nav/Comm, your Apollo GX will provide information about the VOR or Localizer tuned by the SL30. The Apollo SL30 with SW version 1.2, or later, sends the Tuned Station information once every second. Earlier versions of the SL30 only sends data when the frequency is changed. If the Apollo GX shows a different frequency than is shown on the SL30, press the F/F key on the SL30 to synchronize the units.
Reach the Tuned Station display, as shown below, by pressing NAV and turning the LARGE knob. The tuned station identifier and its frequency are shown, as well as the distance to it from your present position and your current ground speed. The Distance, Speed, and Time to waypoint information is sent by the Apollo GX for display on your Apollo SL30. The pilot should verify the station identification prior to navigation use.
Tuning to a VOR The selected VOR frequency on the SL30 is sent to your Apollo GX. The Apollo GX searches its database for a unique identifier for that frequency within 200 nm of your position. If a unique match is found, the selected VOR identifier, frequency, the distance from your present position, and your ground speed are shown on the Apollo GX display. The Apollo GX will send Distance, Speed, and Time to waypoint information to the SL30. If no frequency is found, or two or more are found, within 200 nm, no information will be displayed. All VORs are utilized, even those without TACAN or DME. Once a VOR is identified it will continue to be tracked even beyond 200 nm.
Navigation Basics

Tuning to a Localizer When the connected SL30 is tuned to a Localizer frequency, the SL30 sends the decoded Localizer identifier to the Apollo GX. The Apollo GX searches its LOC-DME database for an identifier match. If the Localizer is found to be a co-located LOC-DME, the Apollo GX will provide Distance, Speed, and Time information to the SL30 and for the Tuned Station page on the GX.
Navigation Basics

Press the MAP key to reach the Moving Map function and view the progress of your flight on a graphic display. Your present position, nearby waypoints, and special use airspaces display options are user-selectable. Three main pages are available in the Moving Map function: full screen map, split screen with map and Nav info, Search & Rescue (SAR) when selected, and map setups.
Map + Nav (+ Comm GX60/65)
Map + Nav Info
Route Line, Map Orient,
Symbol & ID Setup
Track History (On, Save By, Interval)
Track History (Strategy, Clear, % Used)
Airspace Types (B, C, MOA, Training, Unknown, Alert, Caution, Danger, Restricted, Prohibited, & Warning)
The full screen map page of the Moving Map function shows a graphic map of the aircraft position, nearby user-selected waypoints, airspaces, track history, and your route. The aircraft position is shown by an airplane symbol near the center of the display. The TO waypoint identifier is shown in reversed text on the upper left corner. The bearing from your current position to the TO waypoint is shown on the upper right corner. The map scale is shown in the lower left corner. The distance from the current position to the TO waypoint is shown in the lower right corner. A 5 nm “ATC Ring” can be drawn around airports that have a control tower.

Special Use Airspace Sector
Special Use Airspace Outer Ring
Bearing to the TO Waypoint

ATC Ring - approx. 5 nm Radius
Distance to the TO Waypoint
Controls The LARGE knob moves to different pages of the Map function and selects waypoints when scanning. The SMALL knob changes the map scale.
Waypoint Type Keys The smart keys select the display of the waypoint types. The waypoint types selectable from the map view are: Airports, VORs, Intersections, User-defined, and NDBs. Press the smart key to control the display of the waypoint type. There are three selections possible: waypoint identifier and location symbol, location symbol only, and off. Pressing the smart key subsequent times will control which selection is made. The change will also be displayed on the map setup pages.
A solid, reversed waypoint type annunciator above the smart key means the waypoint identifier and location symbol will both be displayed. A bold outline of the waypoint type annunciator will show only a symbol on the waypoint location. A thin outline around the waypoint type means that it is turned off and no information for that waypoint type will be displayed on the map.
APT
APT
Waypoint List Keys The Waypoint List smart key shows a number. Press the key to scroll through the list of available waypoint types available for selection.

Waypoint Scan Key The Waypoint Scan smart key allows you to select an airport to get information about while viewing the map.
Map Scale The Map Scaling is controlled by turning the SMALL knob while viewing the map. The map scale value shown is the vertical height of the screen in nautical miles. Map scale choices in nautical miles are: 0.1, 0.2, 0.5, 1, 2, 5, 10, 15, 20, 30, 40, 50, 75, 100, 150, 200, 250, and auto. The auto selection automatically adjusts the map scale so the “TO” remains on the display until the aircraft passes over the waypoint.
The Map and Nav Info page of the Map function provides a split screen showing the moving map and selected navigation information. The navigation information provided on the right side of the display includes: the current TO waypoint identifier, distance and bearing to the TO waypoint from your current position, ground speed, aircraft current track, and the map scale.
Moving Map Functions · Map and Nav · Info

Distance to the TO Waypoint

aPDX 44.2
Bearing to the TO Waypoint
0.01> 30
Cross Track Error Distance & Direction
Map Setup The map setup function allows you to select the route line, map orientation, waypoint types that will be displayed, airspace type, and special use airspaces, as well as what airspace alerts will appear when an airspace is penetrated.
Route Line A Route Line can be drawn for the legs of the active route when the selection is turned on. A route line is not drawn for procedure turns.
Route Line ATC Ring
Bearing to the TO Waypoint
7S5 SLE 6S4
Distance to the TO Waypoint
Route Line:On Map Orient:North Map Ref:Plane ·

Map Orient The Map Orient selection allows you to choose how the top of the map display is oriented.
North Up - The display is oriented so that vertical
lines on the map are aligned with magnetic north. The aircraft symbol is centered in the display and will point towards the direction you are flying.
DTK Up - The Desired Track for the current flight
plan leg is the top of the display. The aircraft symbol is at the bottom of the display and will point towards the direction you are flying.
Track Up - The direction that your aircraft is moving
towards is at the top of the display. The aircraft symbol is at the bottom of the display.
Route Line:On Map Orient:North Map Ref:Plane ·
Moving Map Functions

Map Reference The Map Reference selection allows you to choose either the Destination Waypoint (Dest) or your current position with an airplane icon (Plane) as the center point of the Moving Map display.
Route Line:On Map Orient:North Map Ref:Plane ·
Identifier and Waypoint Type Selection The Identifier & Waypoint Type page allows you to choose the type of waypoint identifiers that will be displayed on the moving map. You may control the look of your map screen for each type of waypoint by choosing to show the symbol and Identifier, symbol only, or to turn that type of waypoint “Off.” The symbol for each waypoint type is shown in each selection. When “Off” is selected, no symbol or identifier will be displayed for that waypoint type. You may use the “smart” keys to toggle through the selections. The “smart” keys always allow you to select their waypoint type while viewing the MAP display. Note that an airport with a runway of 0 length will not appear on either the nearest list, or on the map if a length is set for the runway limit. See page 12 for details on Runway Limits.
Moving Map Functions

APT:¿ID INT:+ID VOR:ÂID NDB:ÁID Usr:ÀID
APT:¿ID INT:+ID VOR:ÂID NDB:ÁID Usr:ÀID
APT:¿ID INT:+ VOR:ÂID NDB:ÁID Usr:ÀID
Moving Map Functions

Track History Your Apollo GX can store a record of its progress in memory that will be shown on the display. The Track History is shown as a series of points on the display following the path of the plane icon. Track history may be recorded by time or by distance at a selected interval. You may also select the Strategy for storing the track history points. The Full strategy choice means that track points will be stored until memory is full. Subsequent track points will not be stored. The Forever strategy will overwrite previous track points when memory is full. The Clear Track selection allows you to clear the existing track history memory whenever you select Yes. The %used value shows the percentage of track history used.
Track History Recording Points

Track History function has two pages where you may set the following options:
Track History On/Off
Save by Distance/Time
Interval for saving Track History
Percentage of memory used (status only) 1. In the Map function, turn the LARGE knob to reach the Map Setup page. Turn the SMALL knob to the first Track History page. Press SEL to start editing the waypoint types. Pressing the TRK and SAV smart keys toggle the available options. Pressing the INTV smart key enables selection of the interval value.
Moving Map Functions · Strategy (Full/Forever)

Trk History:Off Save By:Distance Interval:0.5
Strategy:Full Clear Track:No %used:12
Moving Map Functions

Airspace Setup The Airspace Setup selections allows you to turn Airspace notification (Alerts) or map display of Airspaces On or Off, select the distance and time buffers for airspace alerts, turn ATC rings On or Off, and to choose the Airspace types that will be used. Airspace alerts will not be given during an approach.
Moving Map Functions

Airspace Buffers Three values may be adjusted for Airspace Buffers for determining CLOSE information: distance, elevation, and time. CLOSE distance may be from 0 to 99 nm at one nm intervals. Altitude values are from 0 to 9900 feet in 100 foot intervals. Time values are from 0 to 20 minutes in one minute intervals. From the Map Setup page, turn the SMALL knob three clicks cw to reach the Airspace Buffers page.
Airspace Buffers Dist Alt Time 2nm 500’ 10min
Airspace Buffers Dist Alt Time 2nm 500’ 10min
Airspace Buffers Dist Alt Time 2nm 200’ 10min
Moving Map Functions

ATC Ring Selection When this choice is turned ON, a 5 nm radius artificial “ATC Ring” is drawn on the Map display around airports that have a control tower. From the Map Setup page, turn the SMALL knob four clicks cw to reach the ATC Ring selection page.
Airspace Selections The Airspaces available for selection are: Class B (Off, Outer, or Sector), Class C (Off, Outer, or Sector), MOA, Training, Unknown, Alert, Caution, Danger, Restricted, Prohibited, and Warning. You may select ON or OFF for map display and alerts for each Airspace type.
Moving Map Functions · Outer Sector

The Outer selection refers to the outline of the outside ring extended from the ground on up. Selecting Outer will be useful to VFR pilots who wish to avoid all airspaces. The sector selection refers to the outside edges of the sector from the ground on up unless you have altitude input which then allows for 3-dimensional information. The Sector selection is the default setting and is most useful for IFR flight. An airspace will appear in the Nearest list even if the map or alert selections are set to off. The Map (MAP) and Alert (ALE) “smart” keys also select the options.
Moving Map Functions

When activated, the Search and Rescue (SAR) feature allows a simplified, automated method of performing search patterns. The search patterns supported include parallel line, creeping line, and expanding square. A line showing the route of the pattern may also be displayed on the screen of your GX. Patterns can be based on two grid types: aeronautical sectional charts (US) and a Lat/Lon grid system (Basic). The grid system can be displayed on the Moving Map, as well as the search pattern.
Search and Rescue Map Description The Search and Rescue map page is essentially the same as the regular full map with the addition of the SAR features. However, at various zoom levels, underlying waypoint information will not be shown to allow for the display of SAR information. Smart keys control the Grid Lines (GRD), mark a position with a new User waypoint (MRK), and select a search pattern (PAT).
MRK
PAT
Bearing to the TO Waypoint
c d Quarter Grid Letter Grid Number
Distance to the TO Waypoint
20 27.3

Grid Line Display While viewing the Search and Rescue (SAR) map page, you can choose how the grid lines are displayed. Press the GRD smart key to change the Grid line view. Grid line selection options are slightly different for the two grid types, US and Basic. As you zoom out to approximately 40nm the grid lines will be removed.
US Grid Type The US Grid selection is based on sectional charts as shown in the Sectional chart table.
GRD - No grid lines GRD 1 - Section lines GRD 2 - Section lines and section number GRD 3 - Section lines, section number,
and quarter section lines GRD 4 - Section lines, section number, quarter
section lines, and quarter section letters
Map Display Grid Lines No Grid Number
SAR003
SAR002
20 27.3
Map Display Grid Lines Grid Numbers
GRID2
SAR003
20 27.3
010 T
Map Display Grid Lines Grid Numbers Quarter Grid Lines
GRID3
SAR003
20 27.3
010 T
Map Display Grid Lines Grid Numbers Quarter Grid Lines Quarter Grid Letters
SAR000
SAR003
20 27.3

Basic Grid Type GRD – No grid lines GRD 1 – 60 minute grid lines GRD 2 – 30 minute grid lines GRD 3 – 15 minute grid lines
46º
45º
Search and Rescue Map Setup Page The SAR Map Setup page provides selection of SAR Map (Off/On), Grid Type (US/Basic), and the Position (area of operation).
Sar Map :Off Grid Type:US Position :SEA

For the Basic Grid type, select the Position
quadrant (NW, SW, NE, or SE) with the SMALL knob or the POS smart key. Quadrant lines are defined by the Equator, Prime Meridian, and the International Date Line. For example, the continental U.S. Would be in the NW quadrant, Denmark would be in the NE quadrant, Buenos Aires, Argentina is in the SW quadrant, and Riyadh, Saudi Arabia is in the SE quadrant.

Sar Map :On Grid Type:Basic Position :NW
Moving Map Functions

Set the SAR Position (Basic Grid Type) 1. If you selected the Basic Grid Type, you need to set the SAR Position. From the SAR Map Setup page turn the SMALL knob clockwise to the SAR Position page. The SAR Position page only appears when the Basic Grid Type is selected. The Position location refers to the LAT/LON of the southeast starting corner for the selected grid.
50 º
One degree grid square
SAR Position Reference Point (i.e. Lat 40 and Lon 120)
SAR Position Latitude :40 Longitude:120
Moving Map Functions

Sectional Aeronautical Chart Grids
Chart Ident North Grid Limit
Row Seattle SEA 4900N 4430N 12500W 11700W 576 32 Great Falls GTF 4900N 4430N 11700W 10900W 576 32 Billings BIL 4900N 4430N 109°00W 10100W 576 32 Twin Cities MSP 4900N 4430N 10100W 9300W 576 32 Green Bay GRB 48°15N 4400N 9300W 8500W 544 32 Lake Huron LHN 4800N 4400N 8500W 7700W 512 32 Montreal MON 4800N 4400N 7700W 6900W 512 32 Halifax HFX 4800N 4400N 6900W 6100W 512 32 Klamath Falls LMT 4430N 4000N 12500W 11700W 576 32 Salt Lake City SLC 4430N 40°00N 11700W 10900W 576 32 Cheyenne CYS 4430N 4000N 10900W 10100W 576 32 Omaha OMA 4430N 4000N 10100W 9300W 576 32 Chicago ORD 4400N 4000N 9300W 8500W 512 32 Detroit DET 4400N 4000N 8500W 7700W 512 32 New York NYC 4400N 40°00N 7700W 6900W 512 32 San Francisco SFO 4000N 3600N 12500W 11800W 448 28 Las Vegas LAS 4000N 3545N 11800W 11100W 476 28 Denver DEN 4000N 3545N 11100W 10400W 476 28 Wichita ICT 4000N 3600N 10400W 9700W 448 28 Kansas City MKC 4000N 3600N 9700W 9000W 448 28 St. Louis STL 4000N 3600N 9100W 8400W 448 28 Cincinnati LUK 4000N 3600N 8500W 7800W 448 28 Washington DCA 4000N 3600N 7900W 7200W 448 28 Los Angeles LAX 3600N 3200N 12130W 11500W 416 26 Phoenix PHX 3545N 3115N 11600W 10900W 504 28 Albuquerque ABQ 3600N 3200N 10900W 10200W 448 28 Dallas- Ft. Worth
GSW 3600N 3200N 10200W 9500W 448 28
Memphis MEM 3600N 3200N 9500W 8800W 448 28 Atlanta ATL 3600N 3200N 8800W 8100W 448 28 Charlotte CLT 3600N 3200N 8100W 7500W 384 24 El Paso ELP 3600N 2800N 10900W 10300W 384 24 San Antonio SAT 3200N 2800N 10300W 9700W 384 24 Houston HOU 3200N 2800N 9700W 9100W 384 24 New Orleans MSY 3200N 2800N 9100W 8500W 384 24 Jacksonville JAX 3200N 2800N 8500W 7900W 384 24 Brownsville BRO 2800N 2400N 10300W 9700W 384 24 Miami MIA 2800N 2400N 8300W 7700W 384 24

Selecting A Pattern Three pattern types provide you with the ability to perform a search that best suits your needs. The three types include Parallel Line, Creeping Line, and Expanding Square.
Search Page Press ENTER
Moving Map Functions · Parallel Line

Parallel Line Search Pattern The Parallel Line search pattern selection allows you to create a search pattern along parallel lines based on an established grid.
3 4 7 8 11 12 Start Point
1 2 5 6 9 10 13
Activate pattern 1. While viewing the SAR Map page, press the PAT smart key.
Grid (US):453C1 Spacing :0.5 Direction :N / S

Moving Map Functions

Creeping Line Search Pattern The Creeping Line search pattern is similar to the Parallel Line Search. The starting point is any selected waypoint, rather than a designated grid based on aeronautical sectionals. The creeping line search pattern will straddle the center of your flight path. You may select the following options:
Direction of travel in 1 degree increments
Center of Search Path
Waypoints for leg turns
Search Page Press ENTER

Start:PFC arpt Spacing :1.0 Direction :000·
Start:PFC arpt Spacing :1.5 Direction :000·
Moving Map Functions

Leg Length:5.0 Start:RIGHT Side
Center of Search Path Center of Search Path
Right Side Left Side 1
Leg Length:8.0 Start:RIGHT Side
Leg Length:8.0 Start:LEFT Side
Moving Map Functions · Direction of Pattern

Expanding Square Search Pattern The Expanding Square search pattern is similar to the Creeping Line Search. Rather than parallel lines, an expanding square is radiated from the Starting Waypoint according to the spacing between lines and at an angle selected for the Direction of Travel. You may select the following options:
Pattern spacing (0.2 to 9.9 nm)
Direction of travel in 1 degree increments
Expanding Square Search Page

Start:ONP arpt Spacing :5.0 Direction :000
Start:ONP arpt Spacing :3.5 Direction :000
Moving Map Functions

Mark A Position When viewing the SAR Map page you may save a User waypoint to Mark a location of interest. Pressing the MRK (Marker) smart key saves a User waypoint at the present position of the aircraft when you save the waypoint.
44°30.48N 123°36.09W
010 T aTTD
SAR000
SAR003
SAR002
20 27.3
Moving Map Functions · SAR User Waypoints

Create A User Waypoint By US Grid This feature allows you to set a US Grid coordinate, such as the corner of a grid, as a User waypoint so you can fly Direct-To the starting point in a grid for flying a search pattern. You must have selected the US Grid type on the SAR Setup page to have this display available.
by US GRID Press ENTER
Moving Map Functions · Create User Wpt

Fly Direct To A US Grid After creating a User waypoint for a US Grid, you can fly Direct-To, or set a flight plan to, the starting corner of that grid to begin a search pattern.
Create a User Waypoint By Basic Grid This feature allows you to set a waypoint on the southeast corner Basic Grid coordinate as a User waypoint. You can then fly Direct-To the starting point in a grid for flying a search pattern. You must have selected the Basic Grid type on the SAR Setup page (see page 16) to have this display available.
The SAR Position (see page 18) is a reference point on the southeast corner of a 10° by 10° grid. Each one degree grid is then divided into 30’ and 15’ segments which are noted by alpha characters.
50 º
123 º 124 º
One degree grid square
40 º
SAR Position Reference Point (i.e. Lat 40 and Lon 120)
SAR Position Reference Point (i.e. Lat 45 and Lon 123) 30’ 15’

If you want to fly to the Bravo-Charlie 3 corner of the 45°N and 123°W grid, you would define the corner as a USER waypoint with the name “53BC3.” The SAR position is set to 40°N and 120°W.
46 º
Basic Grid User Waypoint 53BC3
New SAR Position Reference Point (i.e. Lat 45 and Lon 123)
The “5” comes from the 5° added to 40°N. The next number, “3”, comes from the 3° added to 120°W. The first letter, “B”, notes the 30’ grid divisions. The second letter, “C”, notes the 15’ grid division.
by BASIC GRID Press ENTER

Fly Direct To A Basic Grid After creating a User waypoint for a Basic Grid, you can fly Direct-To, or set a flight plan to, the starting corner of that grid to begin a search pattern.
Setting Up A Search Pattern The process for setting up your Apollo GX for a Search and Rescue operation include:
Turn Route Line On (See page 4)
Setup Search and Rescue Map Page (See page 16)
Set Your Search and Rescue Position (Basic Grid only) (See page 18)
Select and activate a Search Pattern (See page 20)
Moving Map Functions

The Apollo GX provides an extensive built-in database of waypoint information to aid the navigator. Waypoints in the database are divided into 5 categories. This structure allows you to easily select a waypoint as a destination, search for waypoint information, search for nearest waypoints, or insert waypoints into a flight plan.
Create WPT by Rad/Dist
The waypoint types are:
Very high frequency omniranges (VORs)
Non-Directional Beacons (NDBs)
En route Intersections (INTs)
User created (USERs)
The following information is available for each waypoint type. Use the waypoint INFO function to get this information as the Introduction describes in “Waypoint Information.”
Identifier, city/facility name, state, & country
Bearing and distance From/To present position
Radio communication frequencies
Airport type (public, etc.)
Fuel availability by type
Runway map, length(s), surface type, & lighting
Approach info (GX50/60 only)

Waypoint comment VOR Waypoint Information
Identifier, name, state, & country
Radial and distance from the VOR
Bearing and distance from present position
Waypoint comment NDB Waypoint Information
Identifier, name, state, & country
Bearing and distance from present position
Waypoint comment LOC-DME Waypoint Information
Identifier, name, & country
Bearing and distance from present position
Waypoint comment INT Waypoint Information
INT (K) - Continental USA Intersections
INT (O) - Other Americas Intersections
Name & country
Bearing and distance from present position

Waypoint comment USER Waypoint Information
Name/Identifier (User entered)
Lat/Lon coordinates (User entered)
Runway Length (User entered)
Bearing and distance from present position
You can access the Waypoint database by either looking directly or by using a feature that draws information from the database, such as using Emergency Search or creating a Flight plan. This section will describe going directly into the database, the other methods of using the waypoint database will be covered in the sections about the specific features. See “Select a Waypoint” in the Getting Started section on page 1 for more details on searching for waypoints.
AIRPORT AAF APALACHICOLA city FL USA
AIRPORT AAF APALACHICOLA city FL USA

AIRPORT PAE EVERETT city WA USA
PDX AIRPORT PORTLAND city OR USA
PDX AIRPORT PORTLAND city OR USA
Multiple (duplicate) facilities, identifiers, or cities with the same name will have a “dup” between the city/facility and state on the bottom row.
PDX AIRPORT PORTLAND city dup OR USA
TTD AIRPORT PORTLAND city dup OR USA
Waypoint Database

AIRPORT TTD PORTLAND-TROUTDA city dup OR USA
The Apollo GX database holds the most needed information about each waypoint. The Airport information is described below. Similar information is available for each waypoint type. This information is shown after selecting the waypoint and pressing INFO.
Home Page This is the page where the waypoint is selected from the Access Database page. The waypoint type, identifier, city/facility name, state/province, and country are shown. Use the SEL key and LARGE/SMALL knobs as described in Getting Information About A Waypoint on page 3.
AIRPORT SLE SALEM city OR USA
Title Page This is the first page shown after pressing INFO. The identifier, waypoint type, facility name, state/province, and country are shown.
SLE AIRPORT MC NARY facil OR USA
Waypoint Database · Airport Info · Pages

Bearing & distance from present position Turn the SMALL knob to show the Bearing and Distance from your present position. An arrow shows the Relative Bearing to the waypoint from your present position.
ppos to SLE Bearing 341°² Distance 121nm
Airport frequencies Turn the SMALL knob to view the available frequencies for the waypoint. In the GX60/65, the center three smart keys indicate the available frequencies. Press the smart key to load the indicated frequency into the Standby position.
UNIC 122.95 TWR 119.10
ILS Info Turn the SMALL knob to view ILS runway information, when available. The waypoint identifier, ILS frequency, and runway are shown.
ILS 110.30 Runway 31
Identifier, type, & elevation Turn the SMALL knob to view the airport type (public/private) and elevation.
Waypoint Database · SLE AIRPORT Public · elev 210ft

Fuel Availability Turn the SMALL knob to view fuel availability.
SLE AIRPORT Available Fuel:
Map Turn the SMALL knob to view a map of the waypoint and location. If the waypoint is an airport, the runway map will be shown. You can change the map scale by pressing SEL and then turning the SMALL knob. Press SEL again to disable map scaling.
34 31 INFO
MSG APT VOR INT
Waypoint Type (Declutter) Controls
Runway Info Turn the SMALL knob to view runway information. For each runway, the length, type, and lighting are shown.
SLE 13 /31 5800ft Hard ILS Lighted

Approach Info (GX50/60 only) Turn the SMALL knob to view information about each approach.
NDB 31
nSL iaf nSL faf RW31 map nSL mahp Scale 4nm h
Lat/Lon Position Turn the SMALL knob to view the Lat/Lon position.
SLE AIRPORT lat 44°54.57N lon 123°00.15W
Sunrise/Sunset Time Turn the SMALL knob to view the Sunset/Sunrise time for the waypoint in UTC time. You can change the day and month to view alternate times by pressing SEL and then using the SMALL and LARGE knobs. Press ENTER if desired to hold the date.
07 Nov utc time SLE Rise15:05 arpt set 00:46
Waypoint Comment Turn the SMALL knob to view the Waypoint Comment page. If there is no waypoint comment, press SEL to start creating a waypoint comment. If a comment has already been created, it will be displayed here. For further details, see Creating Waypoint Comments on page 14.
Waypoint Database · m · f i

Create User Waypoint by
The Apollo GX allows you to create up to 500 of your own waypoints to the waypoint database. You can create a waypoint based on a Lat/Lon or using a radial and distance from another waypoint. The starting Lat/Lon coordinates are your present position You can also add the runway length. Unlike normal database waypoints a User waypoint with a runway of 0 length will appear in the nearest list and on the map if a length is set for the runway limit in the Nearest Search function, see page 12.
by Lat/Lon Press ENT
#000 USER 44°24.29N Rwlen 122°51.52W 0000’
H000 USER 44°24.29N Rwlen 122°51.52W 0000’
Waypoint Database · Lat/Lon · Create User Wpt

HOME USER 44°24.29N Rwlen 122°51.52W 3000’
Create User Waypoint by Radial/Distance
A User waypoint may also be created where its position is referenced by a Radial and Distance from another waypoint.
000.0° 000.0nm
Ref Wpt: Chg?
000.0° 000.0nm

SMALL knobs to choose the identifier. After the reference waypoint name is chosen, press ENTER.
000.0° 000.0nm
040.0° 012.0nm
#000 USER 44°10.96N Rwlen 121°43.35W 0000’
CABIN USER 44°10.96N Rwlen 121°43.35W 0000’
Waypoint Database

Update the Lat/Lon coordinates of an existing User waypoint to your present position. You may also change the name and other info for the waypoint.
Wpt with Present Pos
with PPos Press ENT
Find wpt to set AA user Press ENTER
Remove a User waypoint from the database.

Find Wpt to Del CABIN user Press ENT
Find WPT to Mod CABIN user Press ENT
CABIN USER 44°10.96N Rwlen 121°43.35W 0000’
HABIN USER 44°10.96N Rwlen 121°43.35W 0000’

You may add comments to up to 200 waypoints. The comments are added while viewing the Info for any waypoint.
SEL
900FT TOWER 14NW NW OF AIRPORT STAY EAST OF TWR

You may delete any of the waypoint comments that you have created.
Waypoint Database · Deleting Waypoint Comments

The Update User Waypoint function allows you to change the position of an existing User waypoint to your present position.
With Ppos Press ENTER
Find Wpt to set #000 user Press ENTER
Datacard The datacard contains all of the waypoint information except what is added by the user. The information contained in the datacard is updated on a regular basis. Contact the factory for obtaining new datacards for the appropriate coverage and time period. C129 operations require using the latest information.
Remove the datacard by pressing the ejector button located to the right of the datacard. Insert the datacard by pushing it completely into the slot. Follow the directions on the card for proper orientation.
Intersections associated with RNAV approaches can be found by loading the approach in which they occur. They may not be contained in the “INT (K)” files of the database. Should you be required to navigate to one of these intersections, you must first load the associated approach and then initiate a “Direct To” to that waypoint in Flight Plan mode.

Flight plans are specific routes between waypoints you may store in the Apollo GX memory. This information is used to calculate useful flight statistics. The Flight Plan function allows you to have up to 30 stored flight plans. Each flight plan may have up to 20 legs. The Active flight plan is always used for the current flight. Inactive flight plans may be activated in the Flight Plan function and copied to the Active flight plan.
Flight Plan Leg pages show the leg number and FROM and TO waypoint identifiers on the display, along with the bearing and distance between the FROM and TO waypoints. One asterisk (*) next to the leg number means that the displayed leg is in the Active flight plan. Two asterisks (**) mean that the displayed leg is the active leg and shows the current FROM and TO waypoints which are being used for navigation.
The first page of each flight plan is the Name Page. The Name Page displays the flight plan name, total distance, and the destination waypoint. Distance is displayed as 0.0 to 99.9 nm at 0.1 nm resolution and 100 to 99999 nm at 1 nm resolution. A diamond Y at the right side of the display indicates that more pages can be viewed by turning the SMALL knob.
Reaching the Flight Plan Function 1. Press FPL to reach the Flight Plan function. You may need to press NAV first if you were viewing the moving map. Press FPL twice to reach the flight plan home page. Turn the LARGE knob to view the

Flight Plan pages. The active leg is the default page you will see when pressing FPL once.
EUG to SLE 1** 353° 48.0nm arpt arpt
Active Flight Plan The first plan in the Flight Plan function is the Active plan and is noted by the name *Active* with asterisks. This name cannot be changed in the Active page.
Creating a Flight Plan
The basic steps for creating a flight plan include: entering the plan name and inserting waypoints. You may then view flight plan information, activate the plan, and use the other options.
WPT4
WPT3
WPT2

Press SEL to Create a New Flight Plan
R_______
to Ins Wpts or SEL for Options
1 Press SEL to Edit Leg

Ins? to 1 ___° nm
AIRPORT EAA EAGLE city AK USA
AIRPORT EUG EUGENE city OR USA
EUG to Ins? 1 ___° nm
Flight Plan Functions

SLE to Ins? 2 ___° nm
Press SEL while viewing a flight plan leg page to make changes.
Press SEL and then turn the SMALL knob while viewing the flight plan name page to activate or to choose other options. See the Flight Plan Options description on page 14 .
The Apollo GX will automatically sequence from one leg to the next as you fly past each waypoint. A line that evenly divides (bisects) the angle between the two legs determines when the flight plan sequences to the next leg.
In the example below, the dashed line describes the area where the flight plan will sequence from Leg 1 to Leg 2 and for the last waypoint (Wpt 3).
FROM TO
TO
WPT 2 WPT 3
FROM
WPT 1

Two types of information are available within flight plan legs: waypoint and flight information. Pressing INFO will provide information about the destination waypoint. Information about the ETA, ETE, Ground Speed, and Fuel is also available for each leg by selecting which option you like to view in the leg display.
Chg? to SLE 1 353° 48.0nm arpt arpt
EUG to SLE 1 353° 48.0nm arpt arpt
EUG to SLE 1 353° 48.0nm Leg ETE 00:30
Flight Plan Functions · Flight Plan · Leg Information

ETA Estimated Time of Arrival is for the displayed TO waypoint and requires an actual ground speed of more than 5 knots. If there is no valid ETA for the leg, dashes will replace the value.
EUG to SLE 1 353° 48.0nm ETA 17:36
ETA? ETA? is the same as ETA, except the Estimated Ground Speed is used for the calculation.
EUG to SLE 1 353° 48.0nm ETA? 17:27
Leg ETE The Estimated Time En Route between the displayed FROM and TO waypoints. Leg ETE requires an actual ground speed of more than 5 knots. If there is no valid ETA for the leg, dashes will replace the value.
EUG to SLE 1 353° 48.0nm Leg ETE 00:27
Leg ETE? Leg ETE? is the same as ETE, except that Estimated Ground Speed is used for the calculation. See Estimated Ground Speed on page 16 for more details.
EUG to SLE 1 353° 48.0nm Leg ETE? 00:27
ETE Estimated Time En route in the Active flight plan is from your present position. In an inactive flight plan, ETE uses the FROM waypoint. ETE requires an actual ground speed of more than 5 knots. If there is
Flight Plan Functions

no valid ETE for the leg, dashes will replace the value.
EUG to SLE 1 353° 48.0nm ETE 00:27
ETE? ETE? is the same as ETE, except the Estimated Ground Speed is used for the calculation. See Estimated Ground Speed on page 16 for more details.
EUG to SLE 1 353° 48.0nm Leg ETE? 00:24
Fuel To? Fuel shows the amount of fuel required to get from the FROM waypoint to the TO waypoint for an inactive plan or from the present position to the TO waypoint for the Active flight plan. See Estimated Ground Speed on page 16 for more details.
EUG to SLE 1 353° 48.0nm Fuel To? 32usg
In the Active flight plan, the Fuel? Calculation uses the Estimated Fuel Usage value and the actual ground speed. The Estimated Fuel Usage value must be greater than zero, and the actual ground speed must be greater than 5 knots. If there is no valid Fuel? for the leg, dashes will replace the value.
In an inactive flight plan, the Fuel? calculation uses the Estimated Fuel Usage value and the estimated ground speed. The Estimated Fuel Usage value must be greater than zero, and the actual ground speed must be greater than 5 knots. If there is no valid Fuel? for the leg, dashes will replace the value.
Flight Plan Functions

Direct-To If the leg page displayed is the currently active leg of the Active flight plan, and a Direct-To waypoint has been entered, the From waypoint will say “Direct.” The leg just prior to the currently active leg displays the leg as if the “Direct” waypoint did not exist. After sequencing, the “Direct” disappears, and the currently active leg once again displays the waypoint identifier. See page 31 for more details on using the Direct-To function.
Direct to WPT4 2** 026° 125nm —— arpt
Leg 3 Leg 4
WPT5
WPT2
While viewing a leg page of the Active flight plan, pressing ENTER will provide the option for making the displayed leg the active leg. Press ENTER to activate the leg. Follow your CDI to intercept Leg 3. You cannot manually select a DME-Arc as a flight plan leg.
SLE to MMV Press ENTER to Activate leg

Leg 3 Leg 4
MMV
WPT5
CDI
WPT2
You can alter any of the information you entered into the flight plans. The editing options include: Chg?, Ins?, and Del?
Chg? - An existing waypoint can be changed if at least one valid waypoint exists in the database.
Ins? - A waypoint can be inserted before an existing waypoint if at least one valid waypoint exists in the database. Inserting a new waypoint into the Active flight plan before or after the current TO waypoint does not affect the currently active leg. Inserting a new waypoint into the active leg’s TO waypoint will immediately change navigation to the new TO waypoint.
Del? - An existing waypoint can be deleted if it is not one of only two waypoints in the Active flight plan, except if the From waypoint is indicated as “Direct,” which can always be deleted. When the “Direct” indicator is deleted, the waypoint that was overwritten by “Direct” will return as the original FROM waypoint. If you delete the current TO waypoint, the NEXT waypoint, if available, becomes the current TO waypoint. If the last TO waypoint is deleted, the previous From waypoint becomes the current To waypoint and the active leg number will be reduced (i.e. from leg 7 to leg 6).

Changing Existing Flight Plan Legs 1. In the Flight Plan function, turn the LARGE knob to a flight plan and then use the SMALL knob to display the leg of the plan that you want to edit.
HIO to TTD 3 070° 23.0nm arpt arpt
HIO to Chg? 3 070° 23.0nm arpt arpt
AIRPORT DLS THE DALLES city OR USA
HIO to DLS 3 067° 75.0nm arpt arpt
Inserting a New Waypoint 1. In the Flight Plan function, display the leg of the plan that you want to edit.
HIO to DLS 3 067° 75.0nm arpt arpt
Flight Plan Functions

HIO to Chg? 3 067° 75.0nm arpt arpt
HIO to Ins? 3 067° 75.0nm arpt arpt
AIRPORT TTD PORTLAND city OR USA
HIO to TTD 3 070° 23.0nm arpt arpt
Deleting a Waypoint 1. In the Flight Plan function, display the leg of the plan that you want to edit.
HIO to TTD 3 070° 23.0nm arpt arpt
Flight Plan Functions

HIO to Chg? 3 070° 23.0nm arpt arpt
HIO to Del? 3 070° 23.0nm arpt arpt
HIO to DLS 3 067° 75.0nm arpt arpt
Before Deleting Leg After Deleting Leg
Leg 3 Leg 4 DLS
HIO
MMV
MMV
SLE
SLE
EUG

In the Flight Plan function you may make changes to a flight plan.
Activate Pressing ENTER when the “Activate” option is displayed copies the selected inactive flight plan to the active plan and activates the plan starting at Leg 1. If you have gone past a given leg, the next appropriate leg will be activated. In the Flight Plan function, turn the LARGE knob to view the available flight plans. Only Inactive plans may be Activated.
When you Activate a flight plan, the Inactive flight plan is “copied” to the Active plan. Any changes made to the Active plan will have no effect on the original Inactive plan.
If you have made any changes to the Active plan, you can save it by copying it into a newly created Inactive plan. See Saving an Active Flight Plan on page 24 .
Copying Route 2 to *Active* Plan

Rev Activate Pressing ENTER when the “Rev Activate” option is displayed copies the selected flight plan to the active plan in reverse waypoint order and starts it at leg 1.
Reactivate Press ENTER when the “Reactivate” option is displayed to reset the active leg to leg 1 and allow waypoint sequencing. Only used for the Active plan.
Rename Pressing ENTER when the “Rename Plan” option is displayed lets you rename the flight plan. Duplicate names are not allowed. Only used for Inactive plans.

Copy Plan Pressing ENTER when the “Copy Plan” option is displayed allows you to copy any existing plan into the current plan, overwriting all of the current plan’s waypoints. You may choose the active or any inactive flight plan.
Estimated Ground Speed While viewing a leg in an Active flight plan, press ENTER when the “Est Gr Speed” option is displayed. This allows you to enter an estimated ground speed value to be used in estimating some leg info options, such as estimated fuel flow, Leg ETE?, ETE?, or ETA?.
The estimated ground speed can be entered from 000 to 999 knots.

Clear Waypoints Pressing ENTER will delete all waypoints in the selected flight plan. The plan name will remain.
Reverse Flight Plan Pressing ENTER when the “Reverse” option is displayed reverses all the waypoints in the current flight plan. This option is available only on inactive flight plans with two or more waypoints.
Estimated Fuel Flow Pressing ENTER when the “Est Fuel Flow” option is displayed allows you to enter an estimated fuel usage value to be used in estimating one of the leg info options.
The estimated fuel flow can be selected from 0000 to 9999 units per hour. The units may be set in the System function (see page 6). Pressing ENTER saves the entered value if the value entered is less than or equal to 999 US gallons per hour, after any necessary conversions are performed. If the value is too large when ENTER is pressed, it is truncated to the largest possible value for the units selected.
After entering the Estimated Fuel Flow, a four second help screen indicates either “Fuel To Uses Actual Gr Speed” when the current flight plan is the active flight

plan or “Fuel To Uses Est Gr Speed” when the current flight plan is an inactive, stored flight plan.
Delete Plan Pressing ENTER when the “Delete Plan” option is displayed deletes the current flight plan. The display returns to the previous flight plan’s name (or first) page. The *Active* flight plan cannot be deleted, in which case this option is not displayed.
Hold The Hold option is available for the Active flight plan when the flight plan status is Active (waypoint sequencing allowed). This function is used while viewing the Name Page. Hold allows you to overfly the Active plan’s current TO waypoint without sequencing. When sequencing is started again, normal operation continues. So, if your aircraft has gone past the waypoint, it will immediately sequence to the next leg in your flight plan. See Flight Plan Sequencing on page 5 for more details.
Flight Plan Functions · Delete Plan? · Hold?

Holding Patterns (GX50/60) A holding pattern is operationally the same as a procedure turn except that you usually intend to make repeated crossings of the waypoint on a specific inbound course. For a holding pattern, like for the procedure turn, the steps will always be to:
While you are in a holding pattern, the CDI/HSI cross-track deviation display and the TO/FROM flag will behave almost exactly the way they would if you were holding at a VOR. The TO/FROM flag will display “TO” prior to reaching the waypoint. The TO/FROM flag will display “FROM” after crossing the waypoint. TO and FROM is determined by position relative to a line drawn perpendicular to the
Flight Plan Functions

selected inbound course and through the waypoint. The CDI will indicate “fly-left” if the aircraft is to the right of the desired track with reference to the selected inbound course. The CDI will indicate “fly-right” if the aircraft is to the left of the desired track with reference to the selected inbound course. As with traditional VOR navigation, these indications are always related to the aircraft position and not to the heading or direction of flight.

When you are ready to depart the hold, you enable sequencing with the OBS/HLD button. If you are on the “TO” side of the waypoint, the flight plan will sequence the next time you cross the waypoint. If you are on the “FROM” side of the waypoint, the flight plan will sequence immediately. The following example shows holding at the Newburg VOR (UBG)
Flight Plan Functions · "FROM" Waypoint

with 020° inbound selected as the “OBS” course to UBG.
"TO" Side "FROM" Side
If sequencing is enabled on the "TO" side of a line perpendicular to the destination waypoint, the flightplan will sequence to the "NEXT" waypoint when you cross the line.
If sequencing is enabled on the "FROM" side of a line perpendicular to the inbound course at the active destination waypoint, the flightplan will sequence immediately to the "NEXT" waypoint.
3S2 (FROM)
Continue The Continue option is available for the Active flight plan when the flight plan status is Holding (waypoint sequencing is not allowed). Pressing ENTER when this option is displayed restarts the Active flight plan and enables waypoint sequencing.
Flight Plan Functions · Perpendicular to 020 · Continue?

Load Approach (GX50/60 Only) This option is available for the Active flight plan when a datacard with approach information is inserted into the GX50/60. Press ENTER to show the available approaches for the destination airport. Press SEL while in the Nav or Map functions to go directly to this option.
Change Approach (GX50/60 Only) This option is available on the Flight Plan home page when an approach is already loaded. Press ENTER to select a new approach for the current destination airport.
*Active* 56.1nm Dest Wpt: PDX Change Approach?
Unload Approach (GX50/60 Only) This option is available on the Flight Plan home page when an approach is already loaded. Press ENTER to unload the approach from the active flight plan. The approach waypoints will be replaced by the destination waypoint.
*Active* 56.1nm Dest Wpt: PDX Unload Approach?
Flight Plan Functions · Load Approach?

Enable Approach (GX50/60 Only) This option is available on the Flight Plan home page when an approach is already loaded, but not enabled, and you are within approximately 30 nm of the destination airport. Press ENTER to enable the approach.
*Active* 56.1nm Dest Wpt: PDX Enable Approach?
Disable Approach (GX50/60 Only) This option is available on the Flight Plan home page when an approach is already loaded and enabled. Press ENTER to cancel the Approach Transition flight mode and return the GX50/60 to Terminal flight mode.
Normal waypoint information about the destination waypoint can be viewed by pressing INFO when the Plan Name Page is displayed. This is the same as pressing INFO to view information about a TO waypoint, except that the Plan Comment page is available by turning the SMALL knob.
A flight plan comment page can be viewed and edited for each flight plan by pressing INFO when the Plan Name Page is displayed and the turning the LARGE knob.
If no plan comment has been entered, press SEL to create one.

Saving an Active Flight
If you have made any changes to the Active plan, you can save it by copying it into a newly created Inactive plan. First, create a new Inactive flight plan without waypoints. Next, select the Copy Plan option while viewing the Active plan. Then, Copy the Active plan into the new plan you created.
Press SEL to Create a New Flight Plan

PLAN 9__

An old navigation method 1. While holding your watch horizontal, point the hour hand at the sun.
Don’t always depend on this method, but it is kind of fun.
Flight Plan Functions

Pressing the SYS key allows you to access the System functions. After pressing the SYS key, turn the LARGE knob to view the available functions: Navigation Info, System Info, Position Sensors, Misc Sensors, and Comm Info (GX60/65 only). Press ENTER when viewing the desired System function.
Turn LARGE Knob , then press . SYS ENTER Press .
Comm Info (GX60/65 Only)
The Navigation Information function allows to make adjustments on the way information is shown in the Navigation function. The pages available include: Airspace Setup, Autonav Time, Nav Mode Display Programming, Magnetic Variation, Flight Timer Trigger, Direct-To Entry Option, and CDI Scaling.
Mag Var Flight Timer
Navigation Info:
Autonav Time Autonav Time is the delay time that each Navigation page will be displayed before rotating to the next page. Time may be selected from one to nine seconds. Press ENTER in the Nav function to activate Autonav.

Autonav Time:
Autonav Time:
Navigation Mode Programmable and Autonav Pages This function allows you to customize both the look of the programmable basic navigation pages and the selection of pages used in the Autonav function. All basic Nav pages are programmable except the first (home) page.
Customizing Navigation Pages 1. Press the SYS key. Turn the LARGE knob to reach the Navigation Info page and then press ENTER.
Nav Mode Display Programmable and
ete SLE 00:20 2.00 “¼¼ Dtk 353 48.0nm

ete SLE 00:20 2.00 “¼¼ Dtk 353 48.0nm
GroundSp 100 kts 2.00 “¼¼ Dtk 353 48.0nm
GroundSp 100 kts Trk 353 Dtk 353 48.0nm
Nav Page 2 in Autonav Pages?
System Functions · Yes

Selecting Autonav Pages 1. While you are viewing a Nav page information page, press SEL and then ENTER.
See page 5 for a listing of Nav Page choices.
Nav Page 4 in Autonav Pages?
Restoring Default Nav Pages 1. While viewing the Nav Mode Display Pages, turn the SMALL knob to reach the Restoring Default Nav Pages display.
Press ENTER to Restore Default
Lat/Lon Units The present position may be displayed in either degrees and minutes or in UTM coordinates.
System Functions · Yes · Nav Pages

Nav Page Choices The following displays are available when customizing your Nav displays. Page references are shown in parentheses.
Ete aUAO 02:27 Estimated Time En Route to TO 4wpt ()
Eta aUAO 00:02 Estimated Time of Arrival to TO wpt (9)
Eta aCVO 00:22 Estimated Time of Arrival to last wpt in plan
Ft00:04 Elapsed Flight Time (9)
Trk 318 357 Track Angle and Bearing (7 and 4)
1.74 崬 Cross Track Error (numeric & graphic) (5)
00:00 UTC Universal Coordinated Time (9)
--:-- to Descent Time to beginning of Descent (17)
’Above Hold Feet Above Hold Altitude (16)
EnrtSafeA 7700’ Minimum Safe Altitude (Entire route) (8)
Min SafeA 4300’ Minimum Safe Altitude (Present Position) (8)
Baro Alt 5100ft Barometric altitude (pressure altitude corrected for local altimeter setting) (15)
aTTD Destination (TO) Waypoint
Brg 071½ Bearing and Relative Bearing Indicator (3)
12.7nm Distance to TO wpt in nautical miles (4)
21.9km Distance to TO wpt in kilometers
12.8mi Distance to TO wpt in statute miles
Trk 070 Track Angle (7)
Tae 000 Track Angle Error (7)
330 kts Speed in knots (7)
612kph Speed in kilometers per hour
380mph Speed in miles per hour
GroundSp 330kts Ground Speed (kts, kph, or mph)
Dtk 193 73.5nm Desired Track and Leg Distance (nm or km) (6)
System Functions Blank field

Setting Units of Measurement Nav displays that show distance may be selected to show either nautical miles, statute miles, or kilometers.
Nav Mode Display Programmable and
ete SLE 00:20 2.00 “¼¼ Dtk 353 48.0nm
ete SLE 00:20 2.00 “¼¼ Dtk 353 48.0nm
ete SLE 00:20 2.00 “¼¼ Dtk 353 89.10km
System Functions · Autonav Pages ·

Magnetic Variation Automatic or Manual Magnetic Variation can be set in this page. Automatic is the default setting on power-up, unless the database is invalid. Manually set Magnetic Variation to 0° to orient your navigation to True North.
Mag Variation Auto 18°E SEL to Edit
Mag Variation Manual 19°E
System Functions

Flight Timer Trigger The following procedure is used to edit the flight timer trigger speed. The flight timer may be set to start at power-up, or when the ground speed exceeds from 10 to 500 knots. The default (factory) setting is 60 knots. The feature may also be turned off.
Trigger At 60 kts
Trigger At 90 kts
Direct-To Entry Options When you use Direct-To, the Active flight plan (and the FROM, TO, NEXT information) is automatically updated. The “May Clear” and “Never Clears” options affect your flight plan.
If you use Direct-To to center the CDI needle for the current “TO” waypoint, or skip past the TO waypoint to another waypoint already in the Active flight plan, the current leg number of the Active flight plan will be updated, if needed, so that the Direct-To waypoint matches the current “TO” waypoint. In these cases, the Direct-To Entry Option is not a factor.
The Direct-To Entry Option becomes a factor if you go Direct-To a waypoint which is not in the Active flight plan.
System Functions · Flight Timer · Flight Timer

With the May Clear Direct-To Entry Option, the Direct-To waypoint will be inserted in the Active flight plan, and all of the other waypoints will be deleted from the Active flight plan, including approaches.
With the Never Clears Direct-To option, the Direct-To waypoint is inserted before the current TO waypoint. This is the normal, default setting. Use this setting if you are using approaches.
The May Clear option is useful for the pilot who uses the Direct-To function for the majority of flight planning, and doesn’t want to be bothered with a steadily increasing number of waypoints in the Active flight plan. The Never Clears option is useful when you need to respond to a change ATC clearance (i.e., N1234A cleared direct ABXYZ intersection, rest of route unchanged), resuming the previously entered flight plan at a later time.
The default setting for the Direct-To Entry is May Clear. The Apollo GX retains the last Direct-To Entry Option setting when it is powered up.
Never Clears Active Plan
May Clear Active Plan
System Functions · Direct-To Entry · Direct-To Entry

CDI Scaling The CDI Scaling option allows you to select manual or automatic full scale deflection of the internal CDI. Manual full scale deflection options include: 0.30 nm, 1.00 nm, and 5.00 nm. Automatic scaling will use 5.00 nm as the setting. In an enabled approach operation (GX50/60), scaling is locked in automatic and will change to the appropriate scale according to your distance to the destination waypoint.
ªªªªª 5.00nm
ªªªªª 5.00nm
ªªªªª 5.00nm
1.00nm

The System Information area provides the following pages: Software and Database Version, Display test, Owner Info, and Date and Time, .
SW Ver & Serial No.
Comm Radio (GX60/65 Only)
Date and Time 1. Press the SYS key. Turn the LARGE knob to reach the System Information function and press ENTER. Turn the LARGE knob to the Date and Time page.

Software Version The Software Version function provides version information about the Apollo software, serial number, database, GPS sensor, display software.
Apollo GX-series SW Vers X.X SN: 1234567 ·

GPS Sensor SW Version x.x PN:123456789
Fuel Measure Units (GX50/60 Only) The GX50/60 allows you to choose the units of measure for your fuel displays. Fuel units may be displayed as US Gallons (USG), Imperial Gallons (IMG), Liters (L), Pounds (LBS), or Kilos (KGS).
System Functions · Fuel Measure · usg US Gallons

Barometric Measure Units (GX50/60 Only) This function allows you to choose the units of measure for the Local Altimeter Settings. The choices are inches (“) or millibars (MB).
Test Display The Test Display page allows you to test the display segments. In the System Information section of the System function, turn the LARGE knob to reach the Test Display page. Press ENTER to start the test. Pressing any key or turning any knob will cancel the test.
Display Brightness The display brightness of your Apollo GX is automatically controlled by a photocell and set to provide good viewing for ambient light conditions. At times you may want to manually control the display brightness. Default is the automatic mode.

Viewing Owner Information The Owner Information function allows the user to enter their Name, Address, City, Phone, and Aircraft. As a security feature, the user must enter a password to enable editing of the Owner Information.
System Functions · ·

Editing Owner Information It is necessary to enter a password before editing owner information. Editing is then enabled until the unit is turned off.
User Must First Enter Password..
Enter owner Password:
Password Matched Editing Enabled
System Functions

GPS Sensor The GPS Sensor selection provides information about GPS satellite health, the GPS satellites available, information on each satellite, GPS Time, and GPS Reset. See the Introduction to GPS section on page 1 for more information on how GPS works.
Healthy & Visible Satellites
GPS 3D Position Healthy Sats 25 Visible Sats 8 Y

GPS SVs for Fix 28, 31, 27, 26, 19, 07, 02, 18
SV31 Status srch Ele 21° Sig 123 Azimuth 043°
Elevation (Ele)- The angle of a GPS satellite above the horizon.
Signal Strength (Sig) - The relative strength of the received signal from the satellite
Azimuth - an arc, as measured clockwise from magnetic or true north.
SRCH Receiver is searching for the satellite
ACQR receiver is acquiring the signal
TRCK receiver has locked to the satellite’s data sequence
DATA receiver is locked and downloading data from the satellite Until data is received by the receiver, a display may look like the following:

GPS Date and Time Page In the GPS Sensor Information function, turn the SMALL knob to view the GPS Date and Time page. This page is not shown when using the Simulator.
GPS Time (UTC) May 24, 1997 17:54:27
GPS Normal Reset Page Resetting the GPS receiver resends current time, date, and position to the GPS receiver. This forces a new search of the satellites. Use this function when it appears that the GPS receiver is locked up or seems to be taking far longer than it should to lock onto the signals.
In the GPS Sensor Information function, turn the SMALL knob to view the GPS Normal Reset page. Press ENTER to reset the GPS receiver.
Press ENT to do
a Normal GPS Reset
System Functions

The Miscellaneous Sensor section of the System function displays information concerning the Fuel/Air Data Sensor (F/ADS), fuel sensor, and altitude encoder when they are installed. The F/ADS includes a fuel sensor and altitude encoder. The F/ADS monitors fuel flow, air speed, outside air temperature/pressure, and magnetic heading. The F/ADS data is used to compute true air speed, pressure altitude, density altitude, heading, wind direction/velocity, rate of climb, and fuel usage. Turn the LARGE knob to choose the sensor. Turn the SMALL knob to view additional available information.
True air speed, Indicated air speed
Endurance, nm/gal, remaining fuel
True air temp, outside air temp, mach
Range, burn rate, gal used
Density altitude, pressure altitude, rate of climb
Right engine, burn rate, gal used
Magnetic heading, desired heading, turn rate
Left engine, burn rate, gal used
Wind direction (true & mag) wind speed
Full capacity, reserve, message at time
The Encoding Altimeter information is provided when a suitable device has been installed. The Pressure Altitude value is provided by the encoding altimeter is shown on this display. This is the current altitude without barometric pressure adjustment.

Air Data Info If the Air Data Sensor is installed, the following
information is available.
Air Speed True Airspeed - speed of the aircraft relative to the surrounding air speed.
Indicated Air Speed - Speed of the aircraft as shown on the airspeed indicator.
Air data Info TruAirSp 163kts IndAirSp 149kts·
Air Temperature True Air Temperature - Temperature compensated for wind chill factors.
Outside Air - Temperature without compensation for wind chill.
TrueAir° 10°C OutAir° 8°C Mach 0.242
Altitude and Rate of Climb Density Altitude, Pressure Altitude, and rate of climb.
Dens Alt 7390ft Pres Alt 5280ft roc +0020ft/min
Heading and Turn Rate Magnetic Heading, Desired Heading, Turn Rate in degrees per second, and direction of the turn.
Mag Heading 046° Desired Hdg 050° Turn 09°/sec R
System Functions

Wind Direction and Speed True Wind Direction, Magnetic Wind Direction, and the outside Wind Speed are displayed.
Wind Dir 000°Tru Wind Dir 342°Mag Wind Spd 15kts
Fuel Info An installed Fuel Data Sensor will provide the following information.
Estimated fuel Endurance based on the current amount of fuel in the regular (nonreserve) tanks at the current burn rates
Nautical miles per fuel unit
Remaining fuel (not including reserves)
Endurance 20:18 nm per usg —.- Remain 452usg·
Range, Burn Rate, and Fuel Used
Estimated Fuel Range based on current fuel in nonreserve tanks, current burn rate, and current speed
Current Burn Rate in fuel units per hour
Total Fuel Used since power up
Range nm Burn 22.5usg/hr Used 21usg
System Functions · Fuel Endurance

Burn rate for the right engine in fuel units per hour
Amount of fuel used by the right engine since power up
Right Engine Burn 17.7usg/hr Used 11usg
Burn rate for the leftt engine in fuel units per hour
Amount of fuel used by the left engine since power up
Left Engine Burn 16.8usg/hr Used 10usg
Total fuel all tanks hold
Reserve fuel amount
Fuel Warning message time period The values on this display are user selectable. Press SEL to start editing. Turn the LARGE and SMALL knobs to edit the values. Press ENTER when you have entered the appropriate values.
Full 00500usg Reserve 00025usg Message at 30min

Fuel Measure The GX50/60 allows you to choose the units of measure for your fuel displays. Fuel units may be displayed as US Gallons (USG), Imperial Gallons (IMG), Liters (L), Pounds (LBS), or Kilos (KGS).
Press SEL to enable selection. Turn the SMALL knob to choose the desired units and then press ENTER.
System Functions · Fuel Measure · usg US Gallons

Message function is responsible for warning the user of changing conditions which require immediate attention. Press the MSG smart key to view the message. Press the MSG key again to return to the previous function. However, if a new message occurs, pressing MSG will not return to the previous function until all new messages have been viewed.
When a new message exists, the MSG annunciator flashes on and off approximately twice per second, until either the user views the new message, or the condition causing the message goes away. If multiple messages exist, the annunciator continues to flash until all new messages have been viewed.
Most new messages continue to be relevant following viewing of the new message, and are put into the old message list, where they remain until the condition causing the message goes away. Other messages are cleared from the message list as soon as they are viewed (they don’t become old messages). The decision whether a new message becomes an old message after viewing is described for each individual case below in the List of Messages section. The formats of all messages are the same if they are in the new or old message list.

While any old message exists, the MSG annunciator remains steadily on at all times unless new messages arrive or all old message conditions go away.
The home page in message mode is the first new message, if one exists, or the New Message Summary page if no new messages exist.
The New Message page shows how many new messages are stored.
2 New Messages Turn Large Knob For Old Msgs Y
The Old Message page shows how many old messages are stored.
2 Old Messages Turn Large Knob For New Msgs Y
Message Function · New Messages · Old Messages

Messages The following is a summary of the conditions that cause a message warning, and examples of the messages generated for each condition.
Special Use Airspace Messages Following is a list of the types of airspace messages which can be generated. All of the airspace messages become old messages after they are viewed. The Airspace Messages are unique in Message Mode in that they are the only messages which the INFO key is used to find out more information concerning the message. Values for the ceiling and floor may be any positive number less than 100,000 feet. Values may also be Unlimited, Ground, FL (Flight Level, followed by a number, such as, 050), Unknown, or NOTAM (Notice To Air Men).
SOON This condition occurs when penetration of the airspace is within 10 minutes (or user-selected limit in System Mode)
Within 10 Min of
CLOSE This condition occurs when the airspace is less than 2 nm (or user-selected limit in System Mode, see page 11).
Within 2 nm of SUNDANCE MOA
Message Function

CLOSE Altitude This condition occurs when the airspace boundary is within 500 feet, or a user-selected limit in the System function.
Within 500’ of NORTON AFB Class C
INSIDE This condition occurs when the plane penetrates the airspace.
Inside of SAN DIEGO Class B
Empty TO Waypoint: Cannot Compute Nav Anytime the current To waypoint is empty, this message is generated. It becomes an old message after viewing.
GPS Self Test Failure If the GPS self-test fails, a message displays indicating the cause of the failure in four hexadecimal digits. It becomes an old message after viewing.
Message Function · Nav Info

GPS Sensor Lat/Lon Failure When the GPS sensor cannot compute the latitude and longitude, the following message displays. It becomes an old message after viewing.
GPS Position Sensor Cannot Compute Lat/Lon
GPS RAIM Not Available When RAIM detection is not available for the GPS sensor, a warning is generated. The current flight phase is displayed first (Terminal, En Route, or Approach). Approach warnings are for the GX50/60 only. Messages become an old message after viewing.
En route GPS RAIM Not Available
GPS RAIM Position Error When RAIM detection is available for the GPS sensor and it detects a RAIM alarm, a warning is generated and Nav data will be flagged as invalid. The current flight phase is displayed first (Terminal, En Route, or Approach). Approach warnings are for the GX50/60 only. It becomes an old message after viewing.
Terminal GPS RAIM ALARM Position Error
GPS Communication Failure This message appears when communications fail between the Apollo GX and the GPS engine. The message will remain if there is a real problem. You may also see this message if you press the SKIP key during startup before the GPS engine was initialized, in which case there is no problem and the message will go away.
Message Function

GPS HDOP Position Error When the HDOP for the GPS sensor exceeds current flight phase HDOP requirements, a warning is generated and Nav data will be flagged as invalid. The current flight phase is displayed first (either Terminal or En route). Approach warnings are for the GX50/60 only. Messages become an old message after viewing.
Terminal GPS HDOP Position Error
Parallel Track/Approach Conflict (GX50/60 Only) This message appears when the current parallel track conflicts with the selected approach.
PTK - Approach conflict. Press ENT to stop PTK
Enable Approach (GX50/60 Only) This message is generated when an approach is loaded, but not enabled.
Press ENTER to Enable Approach
Approach Enabled Too Late (GX50/60 Only) When an approach is enabled too close to the FAF waypoint, the following message is created.
Abort Approach Approach Enabled < 2nm from FAF
Message Function · GPS Communications · Failure

Set Barometer (GX50/60 Only) When an approach is enabled, you are prompted to enter the local altimeter setting.
Enter Local Altimeter Setting 29.92in
No Valid Altitude Input for Approach (GX50/60 Only) An approach is not valid unless an altitude value is available.
No Valid Altitude Input
Approach RAIM Unavailable (GX50/60 Only) An approach is not valid unless RAIM is available.
GPS RAIM Not Available
RAIM Predict Too Late (GX50/60 Only) When the RAIM prediction occurs too close to the FAF, the following message appears.
Abort Approach RAIM predict not completed by FAF
Lat/Lon Position Jump (GX50/60 Only)
Lat/Lon Position Jump Outputs Flagged
Message Function · Abort Approach · Abort Approach

Altitude Range Error When the altitude encoder reports an altitude that is out of range, the following message is created.
Altitude Out of Range
Altitude Encoder Communications Failure This message appears when communications fail between the Apollo GX and the altitude encoder.
Fuel/Air Data Sensor Communications Failure This message appears when communications fail between the Apollo GX and the fuel air data computer.
Fuel / Air Data
Low Fuel This message appears when the fuel air data computer reports that remaining fuel is below the user-selected threshold value.
Low Fuel Warning Less Than 30 Min
Arrival At Hold Altitude You have arrived at the selected Hold Altitude.
Arrival At 2500ft Target Hold Altitude

Outside Hold Altitude Buffer You have gone above or below the selected Hold Altitude Buffer.
500ft Above Hold Altitude
To NOONS 500ft/min 130kts
Arrival At Auto Descent Altitude
Arrival At 2000ft Target Descent Altitude
Arrival At The TO Waypoint The arrival message is generated when you are within 36 seconds of arrival at the current TO waypoint, except when turn anticipation is active. The arrival message is cleared after viewing it; it does not become an old message after viewing. The arrival condition will also go away without viewing the message after crossing the angle bisector. In the example below, WPT 2 is the TO waypoint. When the aircraft crosses the dotted line, WPT 3 will become the TO waypoint.
This form of the Arrival Alert is provided when not holding at the current TO waypoint. When flying an approach DME Arc, then waypoint is automatically placed on hold. The hold is automatically removed upon arriving at the TO waypoint, prior to receiving the arrival alert.

TO TO
WPT 2 WPT 3
FROM
WPT 1
Apollo GX with F/ADS Wind Info
In addition to the arrival waypoint identifier, the next leg’s desired track is shown when available; otherwise, it is dashed. If wind factors (from the Fuel/Air Data Sensor) and a next waypoint are available, the desired heading is also shown on line three; otherwise, line three is blank. DTK is shown for your next leg when Turn Anticipation is used.
Arrival at Inbound Course When using the Vector to Final, DME Arc Assist, or the Procedure Turn functions, the arrival message will alert you when the course line has been intercepted. The desired track for your next waypoint will be displayed.

Holding at the TO Waypoint This form of the Arrival Alert is provided when holding at the current TO waypoint.
Next Leg is DME Arc This type of Arrival Alert is provided when the next TO waypoint is the end of a DME Arc holding at the current TO waypoint. Press ENTER to transition directly to the NAV mode DME Arc Assist page.
TO Waypoint Sequence When a waypoint sequence occurs and the user has not viewed the arrival alert, the following alerts are provided if you are traveling faster than 5 knots (this reduces the chance of nuisance alerts). The new waypoint, bearing and desired track are provided. This message does not become an old message after viewing.
Normal Sequence This type of Sequence Alert is provided when the next TO waypoint is not the end of a DME Arc.
Message Function · - Holding -

DME Arc Sequence (GX50/60 Only) This form of Sequence Alert is provided when the next TO waypoint is the end of a DME Arc in a nonprecision approach. Press ENTER to transition directly to the NAV mode DME Arc Assist page.
Sequence Alert DME Next-Use ARC Assist? Enter
Auto OBS Crossing Holding Waypoint When a waypoint on hold is crossed to the From side the first time, the following message is provided. This message is not created when you cross the MAP. If you press ENTER, the OBS Desired Track screen is displayed. This message does not become an old message after viewing.
Push ENTER to set OBS Course; NAV/MAP to Exit
User Database Memory Loss This message indicates that one or more user waypoints or user-defined comments had a checksum error. This message is cleared after the message is viewed.
Memory Loss:
Flight Plan Memory Loss This message indicates that one or more flight plans had a checksum error. This message is cleared after the message is viewed.
Flight Plan Memory Loss

User Memory Failure This message indicates that one or more user settings were not within valid limits at power-up and needed to be reset. This message is cleared after the message is viewed.
Memory Failure User Setups Have
Database Expired This message indicates that the datacard expiration date is before the current UTC date. This message is cleared after the message is viewed.
America Database Expires 06/30/97 Version: x.xx
Database Invalid This message indicates that the datacard memory has been corrupted. It becomes an old message after being viewed. Turn the unit off. Pull out the data card and reinsert it. If the problem persists, contact your dealer or the factory for service.
Database Invalid Check Data Card
Manual Magnetic Variation This message indicates that magnetic variation is on a manual setting. This occurs when the database is not valid, or when the user selects manual magnetic variation in System Mode. It becomes an old message after being viewed.
Message Function · Been Reset

Low Internal Battery Voltage This message is generated when low internal battery voltage is detected. It becomes an old message after being viewed. Battery voltage is checked every 15 seconds. This battery backs up the memory for information added by the user, such as user waypoints and stored flight plans.
High Battery Voltage This message is generated when high or zero battery voltage is detected. It becomes an old message after being viewed. Battery voltage is checked every 15 seconds. The unit must be returned to the factory for service. Continued operation is NOT recommended.
Internal Battery Failure:Turn Off Unit/Needs Srvc!
Countdown Timer Expired This message is generated when the Countdown Timer (which must have been counting down) goes to 0. The message is cleared when the user views the message or reactivates the Countdown Timer.

The Apollo GX50/60 may be used to navigate GPS non-precision approaches. These consist of overlay approaches, GPS approaches which overlay an existing non-precision approach procedure such as a VOR, an RNAV, or an NDB approach, and GPS-only approaches. GPS approaches may overlay any type of non-precision approach procedure except for localizer, LDA, and SDF approaches.
GPS approaches may be either Phase II or Phase III overlay, or named GPS-only approaches. The major difference in the overlay approaches is that for a Phase II approach, the underlying approach NavAid(s) must be operating and the aircraft must be equipped for the underlying approach. It is not necessary to monitor the underlying NavAid(s). A Phase III GPS approach may be conducted even if the underlying NavAid(s) are not operating.
Introduction There are three general areas of operation (see the diagram on page 3): En Route, Approach Transition, and Approach Active.
En Route En route operations describe what you do to set up your approach information before you are within 30 nm of destination airport and prior to enabling your approach. Load your approach to the active flight plan. You can load the approach in the Flight Plan function, or as a short cut, press SEL in the Nav function or while viewing the moving map. At 30 nm your Apollo GX will ask if you want to enable approach, press the ENTER button. Then, enter the local altimeter setting. If you are less than 30 nm from your destination when you load an approach, you will be prompted immediately to enable it.
Approach Basics (GX50/60)

Approach Transition Approach Transition operations occur after you enable approach operation. The APPRCH annunciator will turn on. The CDI sensitivity will gradually scale from 5.0 to 1.0 nm full scale per side automatically. The IAF is usually in the Approach Transition operation area. The ACTIVE annunciator will start flashing when you are within 3 nm inbound to the FAF and not on hold (sequencing suspended). When you are 2 nm from the FAF, CDI sensitivity will gradually scale from 1.0 to 0.3 nm full scale per side automatically.
Approach Active Approach Active operation begins when you cross the FAF and ends when you cross the MAP. The CDI is at 0.3 nm full scale per side. The OBS/HOLD Annunciator is on steady. The ACTIVE annunciator is on steady. If the ACTIVE annunciator is not on steady, do NOT continue the approach.
Approach Transition Approach Transition operation begins again when you cross the MAP. Decide whether you are going to land or perform a missed approach. If you are performing a missed approach procedure, press the OBS/HOLD annunciator to enable waypoint sequencing. The CDI will scale back to 1.0 nm.
Waypoint Arrival Alert A standard Waypoint Arrival Alert message is generated when you reach each approach waypoint. Press the MSG button to view and acknowledge the message. Press MSG again to return to the previous display. The Waypoint Alert indicates that you are close (approximately 1 nm for every 100 nm/h or about 36 seconds) to the destination waypoint.
Approach Basics (GX50/60)

CAUTION The Apollo GX and the U.S. GPS Satellites use the World Geodetic System 1984 (WGS-84) horizontal datum for latitudes and longitudes. Approach plate or approach procedure data must be referenced to the WGS-84 or North American Datum 1983 (NAD-83) in order to use the approach. NAD-83 is for all practical purposes identical to the WGS-84 datum. All published U.S. and Canadian approach charts meet this criterion. Prior to using the Apollo GX for any GPS approach other than a published U.S. or Canadian approach, you must first verify that the approach charts and approach waypoints use the WGS-84 or NAD-83 reference system. If the approach data is referenced to any other coordinate system, it can result in an unsafe position error.
The Apollo GX database contains approach information. It is very important that the pilot verify that approach data is current prior to use. The approach data contained in the Apollo GX does not replace or eliminate the need for Approach Plates or published Approach Procedures.
Some approach procedures may not be suitable for the Apollo GX operational characteristics and may be omitted from the Apollo GX database. Since an approach must be in the database in order to be selected and flown using the Apollo GX, it is good pre-flight practice to make sure that the database contains anticipated approaches. Always refer to the charts for a given approach before performing the approach.
Approach Basics (GX50/60)


Approach Basics (GX50/60)

There are three general types of Apollo GX operation:
Load Destination Waypoint
Load Approach Information
Approach Transition (or Approach Enabled)
Enable approach (Method 1 or 2)
30 nm from Destination Airport
Initial Approach Fix
Final Approach Fix
Crossing the Final Approach Fix
Missed Approach Point When conducting an approach, your Apollo GX will progress from En Route to Approach Transition when the pilot enables the approach, then to Approach Active, and possibly back to Approach Transition in the event of a missed approach.
En route operations describe all operations prior to 30 nm from your destination airport. Your Apollo GX is providing en route operation whenever the Approach annunciator light is not on. The default CDI sensitivity for en route is 5.0 nm; however, you may manually select other CDI sensitivities. Generally, you will select your destination airport prior to departure or while en route, and you will usually select and load an anticipated approach from the database into your active flight plan while en route.


Load a Destination Airport The destination must be an airport.
If the desired flight plan is active, go to the next section “Load Approach Information.”
Approach Basics (GX50/60) · Activate? ·

Load Approach Information 1. When a flight plan is active, press SEL while in the Nav function or the Moving Map to go directly to this display. In the Flight Plan function with the active flight plan displayed, press SEL to reach the “Load Approach?” selection.
VOR 28R
ENGLL iaf NAOMI faf vPDX map vBTG mahp Scale 19nm
NDB 28L
nIA iaf nIA faf RW28L map vBTG mahp Scale 16nm

Approach Transition Operation begins when you enable an approach that has already been selected from the database and loaded into the active flight plan. The Approach annunciator will be on (and the Approach Active annunciator will be off) to indicate that your Apollo GX is operating in Approach Transition. The CDI sensitivity is locked at 1.0 nm for Approach Transition.
CDI Scale = 1.0nm
2nm to FAF 3nm to FAF
CDI Scale Transitions 1.0 to 0.3nm CDI Scale Transitions 5.0 to 1.0nm ACTIVE Annunciator
Approach Transition Operation will usually be preceded by En Route Operations. Approach Transition will be preceded by Approach Active in the event of a missed approach or a canceled approach.
Enable Approach - Method 1 Press ENTER when the “Enable Approach?” prompt is displayed as a message. The message will occur when an approach is loaded from the database and the aircraft is 30 nm or less from the destination airport. This message-prompt is repeated at 3 nm inbound to

the FAF if the approach has not yet been enabled. You will then get a message to enter the local altimeter setting.
Enable Approach - Method 2 When an approach has been loaded, the aircraft is less than 30 nm from the destination airport, and the approach has not yet been enabled, pressing FPL will result in the “Enable Approach?” prompt. If you press SEL while in Nav or Map mode home pages, the prompt will also appear. Press ENTER when this prompt is displayed to enable the approach. You will then get a message to enter the local altimeter setting.
At 30 nm from Destination Airport 1. At 30 nm from the destination airport, the MSG annunciator will flash. Press MSG. The display will ask if you want to “Enable approach.” Press ENTER to enable the Approach operation. The Approach annunciator will light and the CDI sensitivity will automatically scale gradually from 5 nm to 1 nm full scale.
Press ENTER to Enable Approach
ENTER Local Altimeter Setting 29.92¯
Approach Basics (GX50/60)

Initial Approach Fix (IAF) 1. Prior to the Initial Approach Fix (IAF), the MSG indicator will light to announce a Waypoint Arrival Alert. Press MSG to acknowledge the message and view the instructions to the next approach point.
CDI Scale = 1.0nm
2nm to FAF 3nm to FAF
CDI Scale Transitions 1.0 to 0.3nm CDI Scale Transitions 5.0 to 1.0nm ACTIVE Annunciator
WPT SEQ
Final Approach Fix (FAF) 1. When you are 3 nm inbound to the Final Approach Fix (FAF) and not on Hold (sequencing suspended), the Active light will flash to indicate that you are about to transition to Approach Active and Approach RAIM Prediction will begin. At 2 nm from the FAF, the CDI sensitivity will start to gradually scale from 1.0 to 0.3 nm full scale. At the FAF, CDI sensitivity will be at 0.3 nm full scale.

= 0.3nm
Before, At or After MAP, Press OBS/Hold
Approach Active Operation begins when you cross the Final Approach Fix (FAF) inbound if an approach has been loaded and enabled, the FAF is the active waypoint, and there are no system-detected reasons not to continue the approach (see Message Mode starting on page 1 ). The Approach Active annunciator is illuminated for Approach Active. The CDI sensitivity is 0.3 nm for approach active. Approach active is always preceded by Approach Transition.
As soon as you cross the FAF, the Approach Active annunciator will come on solid indicating that the Apollo GX is providing approach guidance. The active flight plan sequences and the Missed Approach Point (MAP) becomes the active waypoint. Sequencing is now automatically suspended and the OBS/HLD annunciator will be on.

Canceling the Approach will result in returning to Approach Transition operation. The Approach Active light will go out and the CDI will smoothly scale back to 1.0 nm sensitivity. Once Approach Active has been canceled by the pilot, it cannot be made active again except by again crossing the FAF inbound.
Crossing the Final Approach Fix 1. You are now in Approach Active operation. The Approach Active annunciator will light continuously. If the Approach Active annunciator is not lighted continuously, do NOT continue the approach.
Missed Approach Point (MAP) 1. The MSG annunciator will indicate a standard Waypoint Alert as you approach the MAP. Press the MSG key to acknowledge the message. Press the MSG key to return to the previous function.
MSG

CDI Scale Transitions 0.3 nm to 1.0 nm If Missed Approach

OBS/HLD
MSG
MSG
When you have reached the Missed Approach Point, you must either decide to land or not land. The Apollo GX will continue to provide guidance on an extension of your inbound course to the MAP. The MAP will remain the active waypoint, the TO/FROM flag will indicate FROM, and the Apollo GX will continue to display navigation data such as bearing and distance relative to the MAP.
If you have decided not to land, you will then follow either the published or alternate missed approach instructions. Missed approach instructions can be very complex. However, the Apollo GX can be used to provide guidance for virtually any missed approach.
The steps for a missed approach are as follows:
OBS/HLD
Approach Basics (GX50/60) · Missed Approaches

approach. You will now return to Approach Transition mode. The Approach Active light will go out and the CDI will gradually go back to Approach Transition CDI sensitivity (from 0.3 nm to 1.0 nm full-scale).
As soon as you enable sequencing, the Apollo GX will sequence to the next waypoint in the flight plan. This is the next waypoint in the published missed approach procedure.
If the next waypoint is the MAHP, it is an automatic holding point and sequencing will again be automatically suspended. The OBS/HOLD light will come back on. Operation will change from Approach Active to Approach Transition.
3. Verify or select the next waypoint in your flight plan. If the active waypoint is not the one you wish to navigate to, select a new active waypoint. If the active waypoint you want is already in your active flight plan, the easiest way to select it is to press FPL, to enter flight plan mode. Turn the SMALL knob until the waypoint you want is shown as the “TO” side of a flight plan leg . Then press DIRECT-TO and ENTER to select the waypoint.
D
Approach Basics (GX50/60)

OBS/HLD
FPL
Whenever the Approach Active annunciator is lit, an approach may be terminated by a single action of the pilot. You may want to cancel an active approach to try the approach again, choose another approach, to proceed to another airport, or in response to an “Abort Approach” message. In any case, you must follow the appropriate missed approach instructions.
OBS/HLD
Canceling an approach does the following:
Sequencing is enabled
The unit returns to Approach Transition operations
Approach Active annunciator turns off
Approach annunciator remains turned on
CDI scales to 1 nm full-scale deflection
RAIM alarm limit goes from 0.3 nm to 1.0 nm Though you have canceled the active approach, it is still loaded and enabled. You may activate a previous
Approach Basics (GX50/60) · Canceling An · Approach

leg or waypoint and navigate to try the approach again. Your flight plan remains unchanged.
You must cross the FAF inbound with the FAF selected as the active waypoint to allow reactivation of an approach. So, set up a course to return to the IAF and then back to the FAF.
MMV to UBG 2* 018 11.6nm arpt iaf
VOR UBG NEWBERG FACIL OR USA
WPT SEQ
OBS/HLD
Turn the SMALL knob to change the flashing value. Turn the LARGE knob to move the cursor. Press ENTER when finished. Press one of the mode keys (i.e. NAV, DB, FPL, or SYS) to quit without changing anything.
Approach Basics (GX50/60) · Repeating an · Approach

OBS DTK 159° UBG iaf auto brg 159 dtk 159
After a missed approach, you may want to select one of the other approach choices for your intended destination airport.
SEL
*ACTIVE* 82.5nm Appr Arpt: SLE Change Approach?
NDB 28L
nIA iaf nIA faf RW28L map vBTG mahp Scale 16nm
Press ENTER to choose the displayed approach.

Direct-To The Direct-To function is used for several purposes. Especially during approach operations, you should be very comfortable with how this feature works. Review the Direct-To section on page 31 if you need a refresher before proceeding with approaches.
If you select a waypoint that is not one of the waypoints already in the active flight plan, use of Direct-To will automatically unload any active approach if you have crossed the IAF. Use of Direct-To also cancels parallel-track operations, if they are in use.
Direct-To Destination Pressing DIRECT-TO once allows you to select a waypoint that you will navigate “Direct-To.” The first character will flash as the Apollo GX is ready for you to select a waypoint to fly “Direct-To.”
Direct-To OBS DTK Pressing DIRECT-TO twice allows entry of a desired inbound course to the selected waypoint. The default is the current active TO waypoint, selection of another waypoint in your flight plan , and selecting automatic or manual sequencing.
OBS DTK: 151 to
°
ROARK iaf man
brg 344 dtk 164
Selection of automatic or manual sequencing is only available after an approach is enabled. Entering a desired inbound course to a waypoint automatically
Approach Basics (GX50/60) · Flight Plan Waypoint

suspends leg-sequencing at that waypoint and lights the OBS/HLD annunciator.
Subsequent pressing of DIRECT-TO toggles between the waypoint selection and OBS DTK choices.
Manually Selecting a Flight plan Leg
Approach operations often result in the need to manually select a leg of the active flight plan. Manual leg selection will often be required when operating with Radar vectors and there is the need to intercept an approach course. It may also occur when flying a DME-ARC to intercept an approach course. You cannot manually select a DME-ARC as a flight plan leg.
LGD to BKE 2** 146° 28.2nm arpt iaf
LGD to BKE Press ENTER to Activate leg
Approach Basics (GX50/60)

A flight plan will sequence to the next leg of the flight plan as the aircraft crosses to the bisector that runs through the “TO” waypoint. The bisector is defined as the angle that is half of the angle between the current leg and the next leg. When the unit is on Hold, or there is no next leg, the bisector is perpendicular to the inbound course to that waypoint. See the section about Holding Patterns on page 24 for more details on FROM/TO waypoints.
Automatic waypoint sequencing when crossing these lines (bisector)
B (APPR)
C (FAF)
X Y
Y X 2 = Y
D (MAP)
In order to keep the Apollo GX from immediately sequencing when such a leg is selected, place your flight plan on hold by pressing the OBS/HLD key prior to selecting the leg. It is then necessary to re-enable sequencing, by pressing the OBS/HLD key again, when established inbound on the desired leg.
Approach Basics (GX50/60) · Flight Plan · Waypoint Sequencing

A procedure turn is a way of crossing the same waypoint more than once in order to accomplish a course reversal. First, make sure that flight plan leg sequencing is suspended. Second, after crossing the waypoint, set the correct inbound course to intercept. Finally, enable sequencing when you are established inbound.
Suspend Sequencing When a procedure turn or course reversal is required, press OBS/HOLD to suspend sequencing. The OBS/HLD annunciator will light. In the cases shown in the diagram below, the Apollo GX will know when a course reversal is required and will automatically suspend sequencing.
Entry at IFAF (Combined) or FAF
If the angle is
Press HOLD manually.
º, then HOLD is automatic. If the angle is >70
IFAF/FAF
MAP
MAP
Set Inbound Course 1. Upon crossing the waypoint you will be prompted to set the OBS course. Press ENTER to reach the OBS desired track page.
Press ENTER to set OBS Course; NAV/MAP to exit

Many pilots are trained to set and fly the outbound course in course reversal form to eliminate reverse sensing of the CDI. In this case, when you are prompted to set the OBS course, enter the outbound course rather than the inbound course as described previously. During the procedure turn, press DIR-TO twice and then set the inbound course.
Enable Sequencing As you intercept inbound course, the GX50/60 will automatically enable sequencing and notify you with a course intercept message when:
The Track Angle Error is 45°
Cross Track Deviation is 1 nm
Procedure Turn at FAF
A special condition occurs when a procedure turn is made at an IAF which is also the FAF. In this case, the Apollo GX50/60 will treat the waypoint as the IAF until sequencing is enabled when you are established inbound.
When you enable sequencing by pressing the OBS/HLD key (OBS/HLD annunciator light turns off), the IAF/FAF waypoint becomes the FAF. If you
Approach Basics (GX50/60)

are less than 2 nm from the FAF when you enable sequencing, then transition to Approach Active, i.e., the CDI sensitivity will begin changing to 0.3 nm full-scale deflection immediately. The approach annunciator will begin flashing immediately if all the conditions exist to allow the approach to go to the active condition (RAIM available, etc.). It is important for you to enable sequencing as soon after becoming established inbound as practical when you want the waypoint to become the FAF.
C D
153º
018º
B
E
OED (IFAF)
146º
MA14 (MAP)
157º 337º
A
Approach Basics (GX50/60)

A holding pattern is operationally the same as a procedure turn except that you usually intend to make repeated crossings of the waypoint on a specific inbound course. Like the procedure turn, the steps will always be:
First, suspend sequencing
Second, set the inbound course.
Third, enable sequencing. 1. Verify that sequencing is suspended, the OBS/HLD annunciator is lit prior to crossing the waypoint. Suspend sequencing by pressing the OBS/HLD key.
OBS/HLD
"TO" Side "FROM" Side
If sequencing is enabled on the "TO" side of a line perpendicular to the destination waypoint, the flightplan will sequence to the "NEXT" waypoint when you cross the line.
If sequencing is enabled on the "FROM" side of a line perpendicular to the inbound course at the active destination waypoint, the flightplan will sequence immediately to the "NEXT" waypoint.
3S2 (FROM)
Approach Basics (GX50/60) · Holding Patterns · Perpendicular to 020

OBS/HLD
Holding at the FAF Holding at the FAF is different from other holding patterns. You must be inbound and have sequencing enabled to allow proper transition to Approach Active at the FAF.
This example shows holding at the FAF, SL (TURNO) for the NDB or GPS Runway 31 Salem (McNary) Airport (SLE).
RW31 (MAP)
SL (FAF)
WPT SEQ
Press OBS/HLD to release the hold as soon as you intercept the inbound course (point A). This will allow you as much time as possible for transition to Approach Active operation. The waypoint SL (TURNO) becomes the FAF as soon as the hold is released.

DME Arcs (Arc Assist)
DME-Arcs are usually used as a method for pilots to intercept a flight plan leg, or a course to a fix. They are sometimes used as a method for reaching a subsequent fix such as a missed approach holding waypoint.
The Apollo GX automates your DME-Arc procedure. As you near the start of the DME-Arc rather than a typical arrival alert, you are prompted that the next leg is a DME-Arc and that you may use Arc Assist. Using Arc Assist is optional. Pressing ENTER will take you to the ARC reference point page. Verify that the reference waypoint is correct.
The CDI and map display can be used for guidance along the DME-Arc. You may also use the Arc Assist page for guidance to fly the arc.

Approach Basics (GX50/60)

Note The desired track shown on an Arc Assist page is relative to the arc, not to the flight plan legs. The DME-Arc is always perpendicular to the present radial and it shows the desired track at the current radial if the aircraft was on the arc. It is the desired no-wind heading if established on the arc. If your distance from the reference waypoint is greater or less than the distance for the published arc, you will need to increase or decrease your heading to intercept the arc.
Vector to Final The Vector to Final function allows you to fly directly
to a final approach course.
When you select the Vector to Final option, sequencing is disabled and the OBS Direct To course is set automatically using the course defined by the FAF to MAP path with the FAF set as the TO waypoint. A course intercept alert will appear when: the Track Angle Error is 45°, and the Cross Track Distance is 1 nm and on the TO side of the FAF. Sequencing is automatically enabled after intercepting the course and within 4 nm of the FAF.
*Active* 41.0nm Appr Arpt: SLE Vector to Final?
Approach Basics (GX50/60)

Course Intercept Next Dtk 312°
The Apollo GX may be used to help guide you to near the start of an ILS approach by using the location of a DME as a destination waypoint. The waypoint type is labeled “LOC-DME,” which stands for the Localizer-DME pair. Be careful when using this waypoint as the Localizer location and the DME location are often in separate locations. Your Apollo GX will use the DME location as the waypoint. Do NOT use the DME location as the start of the approach.
You may use the DME waypoint as a guide to the start of your approach and as a distance reference point for a step-down approach.
Approach Basics (GX50/60) · Navigating · to a DME

RAIM RAIM stands for Receiver Autonomous Integrity Monitor. It is a way a GPS receiver can verify when the signals it is receiving from one or more of the satellites are useable. It does this by using more satellites than are required for a position solution. In essence, the receiver compares the pseudo-ranges, or calculated distance measurements, from the satellites against what it expects. If this comparison yields too big a value, based on the current RAIM alarm limit, an Alarm is generated and you get a message telling you that a RAIM alarm has occurred.
It is important to understand that RAIM provides integrity, not accuracy. Accuracy is the ability of the GPS to determine a correct position with good satellite signals, enough satellites in view, and an acceptable geometric position of the available satellites. Integrity is the ability of the GPS system to detect when its position may not be accurate enough for IFR operations due to bad or false satellite information.
GPS systems limited to VFR use must meet the exact same accuracy requirements as those authorized for IFR use. Systems authorized for IFR use must also have an integrity monitor such as RAIM.
How Is RAIM Used? TSO C129 calls for three different levels of RAIM protection: En Route, Terminal, and Approach. Plus, the receiver has the ability to predict RAIM availability at any given location and time.
Why Predict Availability? Because RAIM requires that more satellites be used than are required for a position solution, RAIM may not always be available. The TSO requires that RAIM be available with a 0.3 nm. alarm limit, from a distance of 2 nm inbound to the Final Approach Fix (FAF) until the Missed Approach Point (MAP) is reached. A means must be provided to allow the pilot
Approach Basics (GX50/60)

to predict whether RAIM will be available at the estimated time of arrival at the destination. Your Apollo GX provides you with a RAIM prediction page. This page allows you to determine if RAIM should be available at any location and time. If it says RAIM will be available, it actually means that it will be available at your predicted time of arrival and plus and minus 15 minutes from your arrival time calculated at 5 minute intervals.
RAIM prediction is required to be done automatically by the equipment for the estimated time of arrival at the FAF and the MAP when you are 3 nm inbound to the FAF.
TSO C129 requires the RAIM alarm limit to be at least 2.0 nm for en route operations, 1.0 nm for Terminal operations, and 0.3 nm for Approach operations.
What are En Route, Terminal, and Approach Operations? Approach RAIM, or 0.3 nm alarm limit, is provided from 2.0 nm inbound to the FAF until you cancel the Approach Active operation (usually at the MAP). Approach RAIM is provided only if an approach is loaded into your active flight plan and it is enabled.
Terminal RAIM, or 1.0 nm alarm limit is provided within 30 nm of your departure and your destination airport (except when Approach RAIM is provided). This is automatic and requires no pilot action. For those of you who are familiar with the traditional definition of Terminal, which was the ability to operate on SIDs and STARs that are only 4 nm wide, the term Terminal has been “redefined” in TSO C129 to mean within 30 nm of your departure or destination.
Approach Basics (GX50/60)

En Route RAIM, or a 2.0 nm alarm limit is provided at all other times.
Note that the three different equipment operation states: En route, Approach-Transition, and Approach-Active are somewhat but not directly related to the three RAIM alarm limits of En route, Terminal, and Approach. The equipment states are defined by the CDI sensitivity and operational requirements. When you depart an airport, the equipment is operating En route, but it is providing Terminal RAIM integrity.
How Often Will RAIM Be Unavailable? RAIM availability depends on many factors, including the number of operational satellites in the sky, the time of day, the location, the receiver design, the antenna mask angle and location, and on the method of baro-aiding. The Apollo GX has been designed such that with an optimal 21 satellites in operation, Approach RAIM availability should exceed 95%. There are currently, at the time this manual was published, at least 24 satellites in operation; however, the Federal Navigation Radio Plan only guarantees that there is at least a 95% probability that 21 will be operational at any given time.
What Is Baro-aiding? Baro-aiding is used to enhance RAIM availability. It is a method where pressure altitude data can be used to provide RAIM availability during some times when RAIM would not be available using the satellites alone.
What does it mean when I get a “RAIM not available” message? If RAIM is not available, your Apollo GX may be capable of continuing to provide good accurate IFR navigation. What you have lost is the ability to tell if a satellite is sending bad data. For all operations except Approach, the FAA has determined that it is acceptable for you to continue to use GPS for IFR
Approach Basics (GX50/60)

navigation as long as you verify the accuracy of your position by other means at least every 15 minutes until RAIM becomes available again. This can be accomplished by cross-checking your GPS position against that of other navigation instruments. Even during times of no RAIM, if your Apollo GPS determines that it cannot provide an accurate position due to poor satellite availability or geometry, it will flag the navigation display as invalid. If the Apollo GX is providing valid navigation data, then it is still capable of providing good IFR navigation as long as the satellite data is good.
What Does A RAIM Alarm Mean? A RAIM alarm means that the navigation data cannot be trusted to be within the alarm limit. A RAIM alarm means that the Apollo GX has determined that there is something wrong with the data it is receiving from one or more satellites. The data may be corrupted by a satellite failure, such as a clock failure, or it may have been corrupted by some form of signal interference. A RAIM alarm will also be accompanied by flagging all navigational displays as invalid. If you should ever see a RAIM alarm, do not trust the GPS position, and revert to other means of navigation as appropriate.
How Often Do Satellite Failures Occur? There is not enough data to provide a good answer; however, it is known that they can and do happen. Satellite clock failures, one of the more probable failures, is more likely to occur on the older Block-I satellites, but this does not mean that it can’t happen on the newer ones. When a satellite failure does happen, it can result in undetected error of miles in the position if a receiver is using the failed satellite in its navigation solution.
When a satellite fails, even if that failure is detected by an earth-based monitoring station, it can be some time before an uplink to that satellite can occur. During that time, there is no way for a GPS receiver to know that the information from that satellite is bad
Approach Basics (GX50/60)

directly from that satellite’s transmissions. An integrity monitor, such as RAIM when it is available, protects you from false or misleading navigation displays resulting from bad satellite information.
The Apollo GX50/60 allows you to manage your RAIM prediction process, besides allowing for automatic prediction. You can manually predict RAIM for a selected waypoint at a given time and date. You may also manually exclude selected satellites for a given time and date.
Manual Prediction The Apollo GX50/60 allows you to manually predict RAIM availability for any waypoint in the database for any selected date and time.
RAIM Available Select Waypoint? 10Nov97 19:42 ·

Excluding Satellites The Apollo GX50/60 allows you to specify satellite outages for RAIM predictions using information from NOTAMs or NANUs.
Approach Basics (GX50/60) · To Ignore Sat · Press SEL

Clearing the Exclusion List You can also easily clear the Exclusion List.
In the case of an emergency, alternate, or a sudden change in plans, you may need to select another airport for an approach landing. You will need to cancel the previous flight plan and then set a new course. The following three step method includes: 1) clear the current flight plan waypoints, 2) select and fly direct-to a nearest airport, and 3) load an approach for the nearest airport. This same procedure, except for the approach, can also be used for any waypoint type.
Clear Waypoints 1. Press FPL twice to reach the Flight Plan home page.
FPL
*Active* 50.2nm Dest Wpt: SLE Clear Waypoints?

Fly Direct-To a Nearest Airport 1. Press the NRST key. Turn the SMALL knob to choose the nearest desired airport.
Near 1 to PPos CVO AIRPORT Brg 154°± 5.4nm
AIRPORT CVO CORVALLIS city OR USA
Set New Approach 1. Press SEL. The Load Approach option will appear.
INNOP iaf ACVOL faf RW17 map SHEDD mahp Scale 19nm

This section expands on the previous Approach Basics section. A variety of the situations that you may encounter while using approaches is included in this section. Use this section to familiarize yourself with the procedures that you expect to use in normal flight operations.
What you will see
A description of the approach
The examples will, in most cases, include an example Jeppesen and NOS chart of the approach
A drawing of the approach details
A description of the illustration points
An illustration of the approach selection page
Step by step directions explaining the approach
What you will do
Set up a flight plan ending at the approach example airport with the appropriate name
Read through the examples and follow along using the Apollo GX simulator
Use the examples to learn about approach operations with the Apollo GX
Examples included in this section are:
Straight in to Nampa, Idaho (Page 39)
Holding at an IFAF in Medford, Oregon (Page 44)
Missed Approach at Boise, Idaho (Page 51)
VOR reference and missed approach at The Dalles, Oregon (Page56 )
Manual flight plan leg selection (Page 61)
DME Arc at Medford, Oregon (Page 26)
Procedure turn at Medford, Oregon (Page 66)
Procedure turn at Wenatchee, Washington (Page 68)
Approach Examples

Reproduced with permission of JeppesenSanderson Inc. Reduced for illustrative purposes.

Approach Examples

Approach Example 1 -
This example illustrates the approach to Nampa, Idaho. This example was selected because it is a new approach designed especially for TSO C-129 GPS equipment. It is probably as simple an approach to fly with the Apollo GX as there is.
(IAF)
A
12.3 205º
PARMO
115º
B
110º
DEFKI
RW11
D
110º
110º
E
NEMEW
290º
Approach Examples · Straight In

Illustration Points A - Between EMETT (IAF) and PARMO (APPR) B - Between PARMO (APPR) and DEFKI (FAF) C - Between DEFKI (FAF) and RW11 (MAP) D - Between RW11 (MAP) and NEMEW (MAHP) E - In Holding Pattern
EMETT (IAF)
PARMO (APPR)
EMETT iaf DEFKI faf RW11 map NEMEW mahp Scale 32nm h m
RW11 (MAP)
NEMEW (MAHP)
En Route Load and activate your flight plan, then load the approach. Select the Nampa Municipal GPS Rwy 11 approach.
30 nm From Nampa Municipal Airport 1. The message annunciator will flash. Press MSG and then ENTER to enable the approach.
Press ENTER to Enable Approach
Point A (Between EMETT and PARMO) 1. Fly the segment.
Point B (Between PARMO and DEFKI) 1. Fly the segment.
Approach Examples · i GPS 11 · f

Point C (Between DEFKI and RW 11) As you cross DEFKI, verify that the Approach Active and OBS/HLD annunciators are on steady.
Point D (Missed Approach) 1. If you choose a Missed Approach at RW11, cancel the Approach Active operation by pressing the OBS/HLD key. The CDI sensitivity will now gradually scale back to Approach Transition sensitivity (1.0 nm full scale).
OBS/HLD
Point E (Holding Pattern) 1. After crossing NEMEW, you will be prompted to set the OBS course. Turn the LARGE and SMALL knobs to select 290° and press ENTER.
Approach Examples


Approach Examples

Reproduced with permission of JeppesenSanderson Inc. Reduced for illustrative purposes.

Approach Examples

Approach Example 2 -
This example uses an active flight plan ending at the Medford, Oregon airport (MFR). The last two waypoints in this example are the Klamath Falls, Oregon VOR (LMT) and the Medford airport. This approach example involves a procedure turn, a combined IAF and FAF (IFAF), and a MAHP holding pattern at the FAF. This example will include reflying the approach after being cleared from the holding pattern.
Illustration Points A - Inbound to OED from the east B - Outbound on the procedure turn C - On the procedure turn D - Inbound to OED E - Between OED and MA14 F - Turning right and climbing to 6100 feet
G - Outbound from OED to enter the holding pattern H - Inbound to OED in the holding pattern
The simulator does not replicate all procedures exactly. After you select a OBS DTK, the simulator will immediately place the aircraft location in line with the inbound course, bypassing a procedure turn or DME Arc.
H
OED (IFAF) Rogue Valley
A
MA14
F

En route to Medford (MFR) 1. Create a flight plan named “Example 2” with the last two waypoints as the Klamath Falls VOR (LMT) and the Medford airport (MFR).
SEL
NAV
vOED (IAF, FAF, &
MAHP)
vOED iaf vOED faf MA14 map vOED mahp Scale 7nm
30 nm from Medford (MFR) 1. At 30 nm from your destination (MFR), the MSG annunciator will light. Press MSG. At the “Enable Approach” prompt, press ENTER.
Press ENTER to Enable Approach
NAV
OBS/HLD

Point A (Inbound to OED from the east) 1. Flight plan sequencing at OED is disabled because it is an IFAF in preparation for a procedure turn. The combined IAF/FAF waypoint is noted on your Apollo GX as IFAF.
Point B (Outbound on the procedure turn) 1. After crossing OED, the To/From flag will indicate FROM. OED will remain the active waypoint.
With the Apollo GX, when you are prompted to set the OBS course, set it to 342°, the outbound course. Once the procedure turn is started, press DIRECT-TO twice and set the inbound course to 162°.
Point C (On the procedure turn) Fly as you would with a VOR with “162° TO” selected on the OBS. Fly outbound via the 342 radial of OED to execute a procedure turn. Note that the CDI is now reverse-sensing. A distance of 2 to 3 nm outbound is recommended in order to allow adequate distance for the Apollo GX to transition to Approach Active as you pass the FAF inbound.
Approach Examples

Point D (Inbound to OED) 1. As you intercept the 162 inbound a course intercept alert is given. Sequencing is automatically enabled. Turn to intercept the desired course. At 3 nm inbound to OED, the Approach Active annunciator will begin flashing to indicate that approach RAIM prediction is beginning. The transition to approach active is starting.
Point E (Between OED and MA14) 1. Continue to the missed approach point. Verify that the OBS/HLD and Approach Active annunciators are lighted steady.
OBS/HLD
Point F (Choosing not to land at the MAP) 1. At the Missed Approach Point, if you are not going to land, follow your missed approach clearance. The MAP will remain active and your Apollo GX will continue to provide guidance on the final approach course until you press the OBS/HLD key. The published missed approach instructions say “climbing right turn to 6100’ direct OED VOR and hold.” You will then press the OBS/HLD key as soon as you decide to miss the approach.
OBS/HLD
Approach Examples

Point G (At the MAHP) 1. Upon crossing OED, press ENTER when prompted to set the inbound holding course (153°). Use the LARGE and SMALL knobs to select 153°. Then, press ENTER.
Point H (Inbound to OED in Hold Pattern) 1. Once cleared to reshoot the approach and you are established inbound in the holding pattern, fly Direct-To OED (the IFAF).
FPL
LMT to OED 1** 274° 55.9nm arpt ifaf
Approach Examples

Reproduced with permission of JeppesenSanderson Inc. Reduced for illustrative purposes.

Approach Examples


Approach Examples

Approach Example 3 -
This approach example describes an NDB approach from PARMO (IAF) to the Boise, Idaho airport (BOI). This example was chosen primarily because of the unusual published missed approach instructions and to illustrate how to navigate this missed approach with the Apollo GX.
(IAF)
097º 098º 278º
BO (FAF) (MAHP)
A
USTIK
E
B
RW10R
BOISE
(MAP)
BOI
105º
D
Illustration Points A - Between Parmo (IAF) and BO (FAF) B - Between BO (FAF) and RW10R (MAP) C - Just past RW10R (MAP) D - Turn inbound to BO (MAHP) E - Just past BO (MAHP)
En Route to BOI 1. Create a flight plan named “Example3” with the last two waypoints as the Ontario, Oregon airport (ONO) and the Boise, Idaho airport (BOI).
Approach Examples · Missed Approach

BOI APPR
NDB 10R PARMO (IAF)
PARMO iaf nBO faf RW10R map nBO mahp Scale 47nm
nBO (FAF & MAHP)
30 nm from Boise (BOI) 1. At 30 nm from your destination, the MSG annunciator will light. Press MSG. At the “Enable Approach” prompt, press ENTER.
Point A (Between PARMO IAF and BO FAF) 1. The Approach Active annunciator will flash at 3 nm inbound. The CDI sensitivity begins to scale at 2 nm inbound.
Point B (Nearing MAP) Fly the final approach and descend to MDA.
Point C (Missed Approach) 1. When the decision has been made to execute the published missed approach, press OBS/HLD. The active waypoint will become BO (Missed Approach Hold Point). The CDI will gradually scale out to 1.0 nm full-scale deflection. The OBS/HLD annunciator, after turning off briefly, will turn back on as BO (now the Missed Approach Hold Point), is an automatic holding waypoint.
OBS/HLD
Approach Examples · h i · m f

D
BO NDB USTIK (BOISE) facil ID USA
Point D (Inbound to BO) Fly inbound on the new direct course to BO. The OBS/HLD annunciator will remain lighted.
Point E (Missed Approach Hold Point) As you pass BO, establish the new inbound holding course and enter the hold. When prompted, select an OBS DTK of 098° with the LARGE and SMALL knobs. Press ENTER.
Approach Examples

Reproduced with permission of JeppesenSanderson Inc. Reduced for illustrative purposes.

Approach Examples


Approach Examples

Approach Example 4 -
This example for the VORDME A:MUGGZ approach uses a flight plan with the last two waypoints as VOR IMB (Kimberly, Oregon) to The Dalles, Oregon (DLS). This example is illustrates the following points: the step down fixes are referenced to a VOR that is not co-located with the MAP, the nature of the published missed approach instructions, and a DME Arc is part of the approach.
Illustration Points A - Approaching MUGGZ (IAF) B - On the DME Arc between MUGGZ and D185O (ARC) C - Inbound between D185O and CF005 (APPR) D - Between CF005 and FF005 (FAF) E - Between FF005 and MA005 (MAP) F - Turning to intercept 165° to MUGGZ G - Inbound to MUGGZ (MAHP) H - In the holding pattern at MUGGZ
LTJ
185º
165º 165°
DLS
F
MA005
(MAP)
FF005
G E
(FAF)
CF005 (APPR)
D
005º
(IAF) MUGGZ (MAHP)
345º
H
D185O
(ARC)
B
A
Approach Examples · VOR Reference · 15 DME Arc

En Route 1. Create a flight plan named “Example4” with Kimberly VOR (IMB) as the last waypoint before The Dalles, Oregon (DLS) as the destination airport.
SEL
MA005 (MAP)
DLS APPR
FF005 (FAF)
MUGGZ iaf FF005 faf MA005 map MUGGZ mahp Scale 11nm h
D1850 (ARC)
MUGGZ (IAF & MAHP)
Point A -Near MUGGZ (IAF) 1. As you approach MUGGZ (the IAF), you will be prompted that a DME Arc is next. Press ENTER to reach the Arc Assist page.

Point B - On the arc between MUGGZ (IAF) and D1850 (ARC) Use the Arc Assist page and your aircraft heading display to navigate to the selected inbound leg. The Desired Track (DTK) is your tangent to the arc on your present radial. For the right turn arc in this example, there are no other Arc waypoints to identify by radial and distance. If there were more waypoints, the Arc Assist page will continuously show the radial and distance from the Arc Reference making them easy to identify from your approach chart.
Approach Examples

Point C - Inbound between D1850 (ARC) and CF005 (APPR) 1. Flight plan sequencing will operate automatically for each of the remaining waypoints. You will receive arrival and next DTK messages as you cross each waypoint. Press MSG to view the message. Press MSG again to return to the previous display.
Point D - Between CF005 (APPR) to FF005 (FAF) 1. Note that the flight plan waypoints used as step-down fixes are depicted on the Jeppesen Approach Plate, but not on the NOS charts.
Point E - Between FF005 (FAF) and MA005 (MAP) 1. Continue to the Missed Approach Point (MA005).
Approach Examples

Point F - Turning to intercept 165° to MUGGZ (MAHP) 1. When you reach the Missed Approach Point and you wish to fly the published Missed Approach procedure, press OBS/HLD to reactivate waypoint sequencing as you start your climbing right turn.
OBS/HLD
Point G - Inbound to MUGGZ (MAHP) The CDI will scale back to Approach Transition CDI sensitivity. The MAHP (MUGGZ) will become the active waypoint. Use the CDI to intercept the course.
Point H - Holding Pattern Fly the holding pattern.
Reshoot the Approach If you are going to reshoot the approach from a hold at the IAF, select MUGGZ as the IAF in your approach sequence again.
IMB to MUGGZ 2* 292° 77.9nm vor iaf
Approach Examples

You are flying a section of an active flight plan from SLE to BTG to OLM. As you approach the Portland area, you are given Radar vectors to the West of your course. ATC then tells you: “Fly heading 360, resume own navigation, intercept V287 to OLM, then as filed...”
CDI indicates - Fly direct on V287
CDI indicates - Fly right to intercept V287
Original desired flight plan
SALEM
TURNO

Manually select the leg from BTG to OLM (which is V287). Even though you have not yet reached BTG, you will know when you have intercepted this course.
FPL
SLE to BTG 1** 001° 53.2nm arpt vor
Two asterisks after the leg number indicate the active leg of the active flight plan (SLE to BTG).
BTG to OLM 2* 331° 74.4nm vor vor
Approach Examples

Approach Example 5 -
The following example describes the process for intercepting and flying a DME-Arc. This example uses a flight plan from Klamath Falls (LMT) to Medford (MFR) and will navigate along the VOR DME Runway 14 approach. You may also use Ashland (S03) to make your flight a little quicker.
(ARC)
B
OED11 (APPR)
198º
153º
018º
CF14 (APPR)
OED (FAF)
146º
MA14 (MAP)
098º
A
LANKS
(IAF) D15.0
(MFR)
MFR APPR
OED11 (APPR)
LANKS iaf vOED faf MA14 map vOED mahp Scale 29nm
OED (FAF) (MAHP)
MA14 (MAP)
LANKS (IAF)

INFO
LANKS ¾ D3330 ¾ OED11 ¾ CF14 ¾ OED ¾ MA14 ¾
Point A (LANKS to D3330) 1. When you arrive at LANKS, the MSG key will flash. Press MSG to view the message. Press ENTER.
The Arc Assist page will now be displayed. If the displayed default reference is not the desired one for the DME Arc, press SEL and use the LARGE and SMALL knobs to select the correct reference waypoint and the Left Arc. Use this page and your aircraft heading to fly the arc.
Approach Examples

OED11 to CF14 to OED to MA14 Flight plan sequencing will operate automatically. You will receive arrival messages as you cross each waypoint. Press MSG to view the message. Press MSG again to return to the previous display.
MA14 (MAP) and OED (MAHP) 1. When you reach the MAP, waypoint sequencing will be suspended. Land the aircraft.
OBS/HLD
Approach Examples

Approach Example 6 -
This example uses a flight plan from Roseburg, OR (5S1) to Medford, OR (MFR) to demonstrate how to recover when you overshoot the point where you need to place sequencing on hold (Point B). If you cross an IAF without suspending sequencing (pressing OBS/HLD), the Apollo GX will automatically sequence to show MA14 as the next TO waypoint. However, for this approach you must perform a procedure turn first. You must then reset your course to take you through the procedure turn. Reset the course for the procedure turn by selecting OED as the reference waypoint for an OBS DTK course of 153°. The example also illustrates a procedure turn when the IAF and FAF use the same point (IFAF). The example uses the VOR DME 14: OED approach.
vOED (IAF, FAF, &
MAHP)
vOED iaf vOED faf MA14 map vOED mahp Scale 7nm
Illustration Points Point A - Entry into the approach. Point B - Cross OED (IAF) and head outbound. Point C - Make procedure turn. Point D - Course intercept. Point E - Approach active.
C D
153º
018º
A
B
OED (IFAF)
E
146º
MA14 (MAP)

3. If you still need to fly the procedure turn to lose altitude, set the OBS course for the inbound course. Press DIRECT-TO twice to reach the OBS page. Use the SMALL and LARGE knobs to select 153° and select OED (IFAF) as the reference waypoint. Verify that waypoint sequencing is set to “auto.” Press ENTER to establish an inbound course. Note that your CDI will “reverse-sense” while outbound, just like a VOR with 153°-TO selected on the OBS. Also, the TO/FROM flag will change to TO.
Approach Examples

Approach Example 7 -
For this example, use the VOR or GPS-B approach for Wenatchee, Washington. You will start the approach using the CASHS transition. The example involves a procedure turn at the FAF that is not also the IAF.
VOR B
vEAT iaf FF285 faf vEAT map vEAT mahp Scale 5nm
& (MAHP)
FF285 (FAF)
Illustration Points Point A - Between CASHS and EAT. Point B - A heading of 105° between EAT and FF285. Point C - Continue on a heading of 105° between FF285 and the procedure turn until beyond FF285. Point D - Make the procedure turn. Point E - Intercept the 285° inbound to FF285.
A
073º
105º
B
FF285 (FAF)
C D
60º
E
285º
240º

The Apollo GPS may be used to identify waypoints that require DME distance information on an instrument approach by using the LOC-DME as a destination waypoint. The waypoint type is labeled “LOC-DME,” which stands for the Localizer-DME pair. Be careful when using this waypoint as the Localizer location and the DME location are often in separate locations. Also, the accuracy of the position of the DME waypoint depends on the accuracy of the information provided in the database. Your Apollo GPS will use the DME location as the waypoint. Do NOT use the DME location for course guidance. You cannot activate an approach to a LOC-DME waypoint, because it is not an airport.
You may use the LOC-DME waypoint as a guide to identify DME-defined points on your approach and as a distance reference point for a step-down approach. The distance value will be accurate, but the internal CDI will point to the DME antenna location, not necessarily the runway centerline. Use your Nav receiver for Localizer and Glideslope course guidance. Use your Apollo GPS for distance information to supplement your DME.
The LOC-DME will appear in its own category when you perform the emergency search function.
Approach Examples · Using the LOC-DME · Waypoint

The following examples of typical approaches illustrate where the LOC-DME waypoint may be useful. In addition, examples using DME information from VOR waypoints are given.
ILS with DME Data from ILS DME Antenna The following example uses the ILS Rwy 10L approach to Portland International airport. This procedure describes the use of your Apollo GPS distance display to supplement the DME distance as you reach the BUXOM intersection.
099 º
Diagram for illustration only. Do not use for navigation.
BLAZR D5.2 IVDG
D2.2 D0.2
BUXOM TRAYL BLAZR
D12.5 D9.1 D5.2
D2.2
D0.2
3.4 3.9 3.0 2.0 0.5
USA
Approach Examples

The Apollo GPS CDI may not be aligned with the
approach course, only the Nav receiver may be used for course guidance.
ete lIVDG 01:54 0.004 “ brg 101½ 5.65nm
DME Data from ILS with Procedure Turn This example uses the ILS DME approach to Rwy 21L at Prescott, Arizona.
ete lIPRC 02:08 0.000 “ brg 209½ 7.17nm
Approach Examples

ILS DME with DME Data from Two VORs on the Field This example uses the ILS DME approach to Rwy 21 at Flagstaff, Arizona. The DME is co-located with the VOR.
ete vFLG 02:54 0.001 “ brg 210½ 8.15nm
VOR DME without GPS Overlay This example uses the Portland, Oregon VOR DME Rwy 21 approach. You arrive at this approach by going from the Battleground (BTG) VOR to the REENY intersection, making a procedure turn, and then following the 215 radial to the PDX VOR. Use your Nav receiver for course guidance and your Apollo GPS for distance information.
Approach Examples

The Apollo GPS CDI may not be aligned with the
approach course, if the magnetic variation has changed since the VOR station was commissioned. Only the Nav receiver may be used for course guidance.
VOR DME with GPS Overlay This example uses the Sunriver, Oregon VOR DME Rwy 18 Sunriver GPS overlay approach. This approach has a GPS overlay. So, in this case, you may use your Apollo GPS for distance information instead of the DME, while using the Nav receiver for course guidance.
Approach Examples · Or

identify FORRS (D13.0), CERAB (D18.0), and the missed approach point (D23.0).
DME Arc Example The following example uses Baltimore’s VOR DME 15 to demonstrate the approach to Martin State Airport. The approach uses a 14.7 DME clockwise arc to guide the aircraft to Runway 15.
M E
D14.7
D
(IAF)
GOVES
SLOAF
D14.7
D14.7
021º
D14.7
039º
047º
D14.7
334º
060º
068º
Diagram for illustration only. Do not use for navigation.
108º 288º
D11.0
(IAF)
108º
SLOAF
CUMBE
GOVES
D14.7
D14.7 R-039 2400’ 2400’ 1800’ 1260’
D14.7 R-334
D14.7 R-021
R-047
D14.7
R-060
BAL VOR 14.7 DME CLOCKWISE ARC
Approach Examples · Arc

just plant your right wing on the bearing to BAL as displayed by the GPS and hold the arc.
If the distance drifts lower than 14.7, widen the
turn a few degrees by turning left. If the distance drifts higher than 14.7, tighten the turn a few degrees by turning right.
Approach Examples

Approach Examples

Waypoints The database waypoints which describe the TSO C129a GPS approaches correspond with the waypoints which appear on the approach procedure charts whenever possible. VORs, NDBs, and named Intersections will appear in the approach sequence as they are on the charts. The Rifle, Colorado VOR will be identified RIL, the Turno Locator/Outer-Marker (LOM) at Salem, Oregon will be identified SL, the Forsyth NDB, at Forsyth Montana will be identified FOR, and the HIKOX intersection, used as an Initial Approach Fix (IAF) for VOR/DME or GPS RWY 3 approach at Casper Wyoming, will be identified as HIKOX.
Many waypoints that are specific to TSO C129a GPS approaches require that a name be assigned to them, such as an Initial Approach Fix (IAF) which is shown on the approach procedure chart as a radial and distance from a VOR. These waypoints may or may not appear on the approach procedure charts. Jeppesen includes the names of many of these waypoints on their approach procedure charts; however, these names are usually not included on National Ocean Service (NOS) charts.
TSO C129 requires the equipment to prompt the pilot to enter the local altimeter setting, if not already entered, at 3 nm inbound to Final Approach Fix, FAF. It also requires that the equipment change RAIM alarm limits from 1 nm to 0.3 nm and to begin changing CDI sensitivity from 1 nm full-scale deflection to 0.3 nm full-scale deflection when 2 nm inbound to the FAF. The TSO also requires that the final leg of the approach be defined as a path between the FAF and the MAP waypoints (bearings to or from waypoints are not allowed for the final segment). For these reasons, a GPS TSO C129a approach must always have an FAF lying on the inbound course to the MAP, even when there is no such waypoint in the
Approach Notes · Overlay

underlying approach. There are many GPS overlay approaches, such as the VOR or GPS-B approach to Wenatchee Washington, where there is no FAF inbound. The EAT VOR is the Initial Approach Fix (IAF), Final Approach Fix (FAF), Missed Approach Point (MAP), and Missed Approach Holding Point (MAHP). When there is no FAF inbound waypoint for a GPS approach, it is necessary to add one so that the equipment can do these TSO required tasks. This equipment-required FAF is called a sensor FAF and it is always located on the final approach course prior to the MAP. If there is already a named waypoint which can be used, it becomes the sensor FAF. If not, a sensor FAF waypoint is created. In the Wenatchee approach example, this waypoint is named FF285. FF285 is the sensor FAF and the inbound course for the approach is 285°. FF285 appears on the Jeppesen approach procedure chart, but not on the National Ocean Service (NOS) approach procedure chart for this approach.
This is especially important to understand when a procedure turn or course reversal is required. If you are inbound from the CASHS intersection, a procedure turn is required. You must execute this procedure turn on your Apollo GX relative to FF285, the TSO C129a FAF, not relative to the EAT VOR as depicted on the NOS chart as it is necessary to cross this sensor FAF waypoint inbound in order for the Apollo GX to go approach active (approach active annunciator lit) and allow you to complete the approach. This is clearly depicted on the Jeppesen approach procedure chart.
Approach Notes

Reproduced with permission of JeppesenSanderson Inc. Reduced for illustrative purposes.

Approach Notes

Another type of waypoint which will have a name in your Apollo GX database, but may or may not appear on your approach procedure chart is an IAF waypoint defined as a radial and distance from a VOR. An example would be the VOR DME RWY 4 approach to North Bend, Oregon. The IAF at the OTH 164 radial at 14 nm is contained in the Apollo GX database as D164N (“D” for DME, 164 for 164 radial, and “N,” the 14th letter of the alphabet, for 14 nm.). It is also depicted on Jeppesen approach procedure charts with this name; however, this name is not found on NOS charts.
Approach Notes

Charts have been reduced for illustrative purposes.

Approach Notes

There are several other types of waypoints which may appear in your Apollo GX loaded approach and which may or may not appear on your approach procedure charts.
Following is a brief description of these types of waypoints and the naming convention followed.
Identification Each waypoint in an Apollo GX flight plan has an identifying type and a name. There are a few exceptions, where some approach waypoints may be “undefined.” When you view the flight plan legs, by turning the SMALL knob while viewing a flight plan in FLIGHT PLAN mode, the display will show a “FROM” waypoint and a “TO” waypoint for each leg. Under the names for the waypoint, the waypoint type is usually displayed although this field may be changed by pressing SEL and turning the SMALL knob to show other information such as leg ETE. The FROM-TO-NEXT page, located one click to the left of the ‘home’ navigation page, always shows the waypoint names and types for this two-leg “window” view of your active flight plan.
Most of the waypoint types for en route waypoints are quite familiar. They include ARPT for Airport, VOR, NDB, INT for intersection and USER for a user-defined waypoint.
The approach waypoint types will usually also have familiar types, but there may be a few types which are new. The approach waypoint types include:
IAF Initial Approach Fix
FAF Final Approach Fix. Note that there must always be a Final Approach Fix inbound for TSO C129a approaches. When an underlying approach, such as a VOR or NDB approach does not have an inbound FAF, one is created or added.
IFAF Combined Initial and Final Approach Fix with no intermediate waypoints. (Sometimes a procedure turn
Approach Notes

or course reversal is required - this usually depends on the direction of flight).
MAP Missed Approach Point
MAHP Missed Approach Holding Point
ARC A DME arc terminator. The preceding flight plan leg is described as an arc to this waypoint. An ARC waypoint may follow another ARC waypoint.
APPR An intermediate approach waypoint. These are sometimes used as step-down fixes or to define a course to the next approach waypoint.
An Apollo GX TSO C129a approach will always begin at an IAF. It will always contain at a minimum an IAF, FAF, MAP, and MAHP sequence. The IAF and FAF may be combined. Waypoints may be used more than once; the same waypoint could be the IAF, the MAP, and the MAHP; however, TSO C129a non-precision approaches require that there always be a distinct FAF to MAP leg. Intermediate waypoints, of type APPR or ARC, may be anywhere in the sequence except between the FAF and the MAP.
The following example uses the VOR DME RWY 12 GPS-overlay approach to Baker City Oregon.
The Apollo GX has a flight plan loaded from the Salem, Oregon airport to the Deschutes VOR, DSD, to the Baker City airport, BKE. An approach, the VOR DME RWY 12 approach with the D272Y (waypoint on the BKE VOR 272 radial at 25 nm.) IAF is selected and loaded. When viewing the flight plan legs, the following legs may be viewed.
SLE to DSD 1 100° 82.6nm ARPT VOR
DSD to D272Y 2* 052° 134nm VOR IAF
Approach Notes

The following legs replace the BKE airport in the flight plan and describe the approach sequence.
D272Y TO D297Y 3* 018° 10.8nm iaf arc
D297Y to D297O 4* 118° 10.0nm arc appr
D297O to CF12 5* 119° 5.0nm appr appr
CF12 to FF12 6* 120° 6.0nm appr faf
FF12 to MA12 7* 120° 6.0nm faf map
MA12 to BKE 8* 120° 6.0nm map mahp
Approach Notes

Reduced for illustrative purposes.

Approach Notes

Charts have been reduced for illustrative purposes.

Approach Notes

When a name must be provided for an otherwise unnamed waypoint, the naming will use the ARINC-424, chapter 7 specified convention whenever possible. There are a few types of waypoints, DME arc waypoints greater than 26 nm from the reference and single character NDB idents, which are not adequately addressed by the ARINC-424 specification. Most of these names are intuitive after you understand a few of the rules. The entire ARINC naming conventions are not included here, but the following guidelines will probably explain the names you see assigned to these waypoints.
Exceptions DME arc or DME-distance/bearing waypoints that are greater than 26 miles from their reference point. The standard ARINC convention for DME arc or DME-distance/bearing (sometimes called Rho-Theta) waypoints is to use ‘D’ followed by the bearing from the waypoint, followed by an Alpha character from A to Z corresponding to the number of miles, from 1 to 26, rounded to the nearest whole mile. A waypoint on the BKE VOR 272 radial at 25 nm would then be named D272Y as is the IAF in the Baker, Oregon approach example above. When the distance is greater than 26 miles, such as for the Topeka, KS VOR DME RWY 3 approach, the waypoint is named by using the first two characters of the reference navaid ID, followed by the bearing from the navaid. The IAF at the Topeka VOR, TOP, located on the 231 radial at 31 nm is then named TO231. The IAF on the TOP 176 radial at 31 nm is named TO176.
Canada and some South American countries have multiple NDBs with the same ident. When these are in the same ICAO region, they can’t both be in the data. When this happens, one airport which uses a Golf NDB, “G,” would have the waypoint named “G.” The next airport that uses a “G” NDB in the approach waypoints would have a waypoint named with the 1 letter ident and ‘NB’ for NDB appended to
Approach Notes · Naming Conventions

it; therefore, it would appear in the database as “GNB” at the second airport.
In general, the following codes are used to correspond to a waypoint type. When they are associated with an approach to a specific runway, the runway is appended. When the approach is not to a specific runway, the approach bearing is appended. These codes are:
FF Final Approach Fix
CF Final Approach Course Fix (used when necessary to define a course to the FAF—all VOR DME approaches require a course fix waypoint).
MA Missed Approach Point
Following the characters will either be a runway number, when associated with a particular runway, or a bearing corresponding to the course at that waypoint. A missed approach point that corresponds to a RWY 12 approach, would then be called MA12 if it is not the runway threshold. If the MAP were the runway threshold, it would be named RW12. A missed approach point associated with a VOR-A approach, where there are no published straight-in minimums to any runway, and where the final approach course is 120 would be named MA120.
Bearing and Distance Waypoints: Distance/bearing waypoints (sometimes called Rho - Theta waypoints), that are defined as a bearing and distance from a VHF navaid, are named with the character “D,” followed by the radial on which they are positioned, followed by a single alpha character from “A” to “Z” that corresponds to a distance from 1 to 26 nm. Thus a waypoint that is on a 350° radial at 10 nm will be named D350J and a waypoint that is on the 250 radial at 15 nm would be named D250O.

Unnamed turn points, intersections, and bearing/distance waypoints: Idents for unnamed turn points, intersections, or bearing/distance waypoints (other than VHF navaid distance/bearing), that are not coincidental with named waypoints, are constructed by using the ident of the nearest navaid together with the distance (rounded to whole miles). If the distance is less than 100 nm, the distance follows the navaid ident. If the distance is 100 nm or more, the last two digits of the miles are placed in front of the navaid ident. For example:
INW 18 INW18
CSN 106 06CSN
TCS 89 TCS89
These are most often used for identifying bends in airways that occur at unnamed positions and other en route uses. It is unlikely that you will often see this convention used to name any approach waypoints, but you will occasionally.
GPS equipment may be used as the primary IFR flight guidance during a non-precision approach without actively monitoring the applicable navaid(s) which define the approach being used. However, the traditional ground-based navaid(s) required for the published approach and alternate should be operational and the associated avionics installed and operational. The approach should be requested and approved by its published name, such as “NDB Runway 24.” Modification of the published instrument approach name is not required.
Approach Notes · Phase II GPS · Approaches

Phase III GPS approaches must contain GPS in the title of the GPS procedure such as VOR or GPS RWY 24. Neither the ground station navaid(s) nor the traditional aircraft avionics is required. If the approach is to be flown using the Apollo GX, it should be requested and approved by the GPS name, such as GPS RWY 24. If it is to be flown with the traditional avionics, it should be requested and approved by that name, such as VOR RWY 24.
You should always plan the route and approach to any required alternate airport as if a supplementary navigation system, such as GPS or Loran-C, may not be available. The traditional en route and approach Navaids must be operating and the aircraft must have the required avionics to use for required alternates. You may use a supplementary system, such as GPS, to navigate to an alternate airport. You may execute a GPS approach to a required alternate, but you must plan for the possibility that GPS navigation will not be available.
FAA guidelines on IFR use of GPS and GPS approaches are contained in an FAA Advisory Circular (AC), AC 90-94. You should be familiar with the information in this AC before attempting GPS approaches.
In order to use the Apollo GX for an approach, the approach must be selected from the Apollo GX database and loaded into the active flight plan. Only approaches found in the Apollo GX database may be flown with the Apollo GX.
Approach Notes · Phase III GPS · Approaches

The Start Up Sequence runs each time the unit is powered on. The Start Up Sequence varies between units due to installation differences. The initial start up message is displayed for about three seconds.
Startup Bypass During the startup sequence, press the SKIP “smart”
key to stop the initial testing. You will be able to use all functions.
Press the COM key during the startup sequence to enable immediate use of the Comm function in the GX60/65.
COM
In the GX60/65, if the Comm software fails, the following message will be displayed. You must then have the unit serviced before you can use it.
FAILURE ! Service Now
If your Apollo GX suffers both EEPROM and RAM failure, you must reset the unit type. Select the unit type with the SMALL knob and then press ENTER. This will allow you the ability to still use the Comm and Approach functions.
Memory Failure Select Unit type

If the owner name has been previously entered (in System Mode), this page with your name is displayed for three seconds. No owner info screen is displayed if the user has not entered the owner data.
Your Apollo GX performs a number of tests at startup to ensure proper operation.
Software Memory Test This is a checksum test of the code memory region. The following screen is displayed for the duration of this test.
In Progress Please Wait...
If the checksum passes, the next screen is displayed for two seconds.

Failure to pass the software checksum test indicates that the software memory is corrupted. The GPS board will not continue operation when the following screen is displayed.
Non-Volatile RAM Tests The non-volatile RAM validation code does the following checks every time the unit is powered up. Any tests which detect a failure reset the failed values. Generally, the non-volatile RAM test pages are not displayed, since in most cases the tests pass.
User Database Memory Failure User waypoint checksums exist for each User waypoint. If the checksums do not match, the User waypoint is deleted. If this occurs, any flight plan which references this user waypoint is also deleted.
In addition, User comment checksums exist for each user-defined waypoint comment. The comment is deleted if the calculated checksum does not match the saved checksum. The following message is then displayed until you press ENTER.
User Database Memory Failure
Flight plan checksums exist for all flight plan information. If a particular flight plan checksum does not match the calculated checksum, the flight plan is deleted, or in the case of the Active Flight Plan, the plan is reinitialized. The following message is then displayed until you press ENTER.
Flight Plan Memory Failure

Miscellaneous NVRAM or EEPROM Memory Failure All other user input values which are held in non-volatile RAM are checked for validity, producing the following message if any of the values needed to be reset. The following message is then displayed until you press ENTER.
Database Test This checksum test compares the database checksum stored on the database card with the calculated database checksum. Since this test may take several seconds to complete, the following screen is displayed until the test is completed.
In Progress Please Wait...
If the checksum test passes, the next screen is displayed for two seconds.
Failure to pass the database checksum test indicates that memory in the database is corrupted, and the following message is displayed until you press ENTER.
Datacard Failed Contact II Morrow

This page shows the database name and expiration date. If the database has expired, press ENTER to continue.
Seed Position Each time the Apollo GX is switched on, it must locate
satellites in the sky to acquire signals before determining a position fix in a complex process involving lengthy mathematical operations. Without a seed position and the current UTC time and date, this process can take 10 minutes or more to complete. Enter a Seed Position to allow the receiver to quickly locate and track available satellites.
After the start up tests, you will always have the choice of entering a Seed Position. The Seed Position is a starting reference point so the GPS receiver knows what satellites to look for. If a Seed Position has been previously entered, you do not need to select a new Present Position or a Reference Waypoint. If you do not make any selections, the Apollo GX will automatically progress into the Navigation function. You cannot enter a seed position in simulator mode.
Entering a Seed Position
Start Up Displays · Database · Message

press ENTER to accept the current position, though this is not required.
Ppos: 44°54.46N 122°59.69W Ref Wpt: Chg?
Press ENTER to change the Reference Waypoint or turn the LARGE knob to change to Lat/Lon Reference Position. Use the appropriate following description: Change Reference Waypoint or Change Lat/Lon Reference Position.
Change Reference Waypoint 1. Press ENTER. The waypoint type will flash. Turn the SMALL knob to select the waypoint type.
Start Up Displays

SMALL knob. Turn the LARGE knob to move to each character of the waypoint name.
Waypoint Type (Airport shown here)
Waypoint Indentifier Underline indicates flashing character
SLE
SALEM
CITY OR USA
Change Lat/Lon Reference Position 1. Set the latitude and longitude coordinates near to your current position. After setting the Reference Waypoint, the first character of the Reference Position Lat/Lon will flash.
Ppos: 44°54.46N 122°59.69W Ref Wpt: Chg?

Clear Active Flight Plan
A series of tests covering connections for IFR flight are tested if your Apollo GX has been installed and configured for IFR flight.
Starting IFR Output Tests
After the completion of all tests the Apollo GX will start normal navigation operation.
CDI Output Tests The CDI (Course Deviation Indicator) outputs are tested first. Each of the following displays is shown for two seconds, during which the external CDI needle should be driven as indicated by the display, which is up to the user to verify.
CDI tests and display screens are provided for CDI Full Right, CDI Half Right, CDI Centered, CDI Full Left, and CDI Half Left.
TO/FROM Flag Output Tests The To/From Flag outputs are tested next. Each of the following displays is shown for three seconds, during which the external To/From flag should be driven as indicated by the display, which is up to the user to verify.

To/From Flag tests and display screens are provided for the To, From, and Off conditions.
Nav Valid and Nav Super Flag Tests The Nav Valid and Nav Super Flag outputs are tested next. Each of the following displays is shown for three seconds, during which the external Nav Valid and Nav Super flags should be driven as indicated by the display, which is up to the user to verify.
NAV VALID FLAG
NAV VALID FLAG and SUPER FLAG
Nav Valid and Super Flag tests and display screens are provided for the Flagged and Not Flagged conditions.
VDI Output Tests (GX50 and GX60 only) VDI (Vertical Deviation Indicator) outputs are tested next. Each of the following displays is shown for two seconds, during which the external VDI needle should be driven as indicated by the display, which is up to the user to verify.

VDI tests and display screen are provided for VDI Full Up, VDI Half Up, VDI Level, VDI Full Down, and VDI Half Down.
VDI Valid and VDI Super Flag Tests (GX50 and GX60/65 only) The VDI Valid and VDI Super Flag outputs are tested next. Each of the following displays is shown for three seconds, during which the external VDI Valid and VDI Super flags should be driven as indicated by the display, which is up to the user to verify.
VDI VALID FLAG and SUPER FLAG
VDI Valid and Super Flag tests and display screens are provided for the Flagged and Not Flagged conditions.
External Annunciator Lamp Tests The external lamp outputs are tested next. The external lamps which are driven by the Apollo GX GPS Navigation Equipment include the message lamp, VFR lamp, parallel track lamp, approach lamp, Approach Active (GX50/60), and OBS/Hold (GX50/60). The lamps are all flashed on for one second and off for one second a total of three times, during which it is up to the user to verify that the external lamps which are connected are working.
EXTERNAL LAMPS Flash All Lamps
EXTERNAL LAMPS Flash All Lamps
Start Up Displays · -Flagged-

Screen Test A full visual display test on each line of the display and all of the annunciators is run next, preceded for two seconds by the following screen.
Test...
The visual display incrementally lights groups of pixels on the electroluminescent display.
The unit shows the GPS signal strength screen in the GPS Sensor function. Make it a habit to check this screen to make sure that the unit is properly tracking visible satellites before you fly. The Apollo GX requires signals from at least four satellites to calculate a 3D position fix (Lat/Lon and GPS altitude). More details are available in the GPS Sensor part of the System section of this manual, see page 17.
GPS 3D Position Healthy Sats 24 Visible Sats 8 Y

GPS SV’s for Fix 31, 27, 26, 19, 07, 02
SV16 Status SRCH ele 11° Sig 000 Azimuth 039°
SV24 Status DATA ele 74° Sig 123 Azimuth 132°
Start Up Displays · Acquiring Satellite · Locked on Satellite

Your Apollo GX is provided with a Flight Simulation program that allows you to “fly” your unit by simulating the speed and altitude. This section describes the procedures used to run the Flight Simulator. You may operate the Flight Simulator in the cockpit or in your home to familiarize yourself with the operation of the Apollo GX.
The Flight Simulator is programmed into your Apollo GX at the factory. The Flight Simulator is activated during start up by pressing the NAV key while you turn the power switch on.
The Apollo GX “asks” you to enter a ground speed and altitude each time the Flight Simulator is started. This speed and altitude information will remain constant throughout the simulation. The Apollo GX uses a simulated GPS sensor to provide position, altitude, speed, and course information. As no external sensors are connected while the simulation is running, no information is displayed about external sensors. The simulated altitude and speed does not change while the Flight Simulator is running.
The Apollo GX uses the position of the first FROM waypoint in the Active flight plan as the initial position and simulates flight along the desired track to each successive TO waypoint. While “en route,” the Apollo GX generates updated navigation information and alert messages consistent with the simulated flight path. When the Apollo GX “arrives” at the final waypoint of your flight plan, it stops waypoint sequencing. The Apollo GX continues to simulate flight past the waypoint and provides bearing and distance information to the last TO waypoint. The simulated flight will only fly direct between waypoints, so it will not follow a DME-Arc on the Map display.
Flight Simulator · About the · Flight Simulator

The following procedure is used to remove the Apollo GX so you can operate it at a location of your choice. . While inserting or removing the GX, Do not exert excessive turning force at the end of the cam lock travel or the unit may be damaged.
and Replacing the Apollo
Note Operation of the GX60/65 transmitter is not permitted in a residential or industrial environment without an appropriate FCC license. Operation of the GX50/60 with a serial port connected to a computer is not currently authorized under FCC part 15 regulations. 4. Replace your GX into the tube carefully. Position the cam lock as shown below. The front lobe of the cam should be vertical. The cam lock mechanism should be fully unscrewed (turned counter-clockwise). Slide the unit into the frame. Turn (clockwise) and carefully hand-tighten (4 in-lb max.) the cam lock mechanism using only the 3/32" hex driver provided in the installation package. Using a larger tool than the one provided makes it easy to exceed the allowable torque on the cam lock resulting in damage to the unit. The unit will be pulled into the frame securing the unit and the connectors will fully engage. Do NOT overtighten. The back of the bezel must only be flush to the mounting tube. If the cam
DOWN
FRONT CAM UP
POSITION CAM FULLY TO REAR BEFORE INSERTION
BEZEL
Flight Simulator · Removing

lock is hard to turn or the unit does not seat fully, the unit is probably binding and the mounting tube should be checked.
The following procedure is used to start the flight simulation. It is recommended that you have a data card properly inserted into the data card slot so you can use the appropriate functions.
Simulator Setups Gr Speed 100kts Altitude 1000ft
Simulator Setups Gr Speed 170kts Altitude 4500ft

Clear Active Flight Plan?
Once you’ve started the flight simulator, you may practice the various operating procedures, such as activating flight plans, entering Direct-To courses, and inserting/deleting/changing waypoints in the Active flight plan. The simulator is also useful for planning purposes; you may create and edit flight plans in the comfort of your office or home. Changes made to flight plans and waypoints while the simulator is running are retained when the Apollo GX is reinstalled in the aircraft.
While the heading follows the DTK on turns and arcs, the simulator aircraft will actually move in a straight line.
Flight Simulator · Yes · Flight Simulator Operations

Or, what to do when nothing works! This section contains information to troubleshoot your Apollo GX product when improper operation is observed. The following table lists possible problems you could encounter while operating the unit. Examine the possible causes of the problem and take the action listed to correct the trouble. If you cannot correct the problem, contact your dealer. If your dealer is unavailable, contact the II Morrow factory at the address and phone number listed.
If efforts to resolve the problem fail, contact your dealer or the factory weekdays from 8:00 A.M. until 5:00 P.M. Pacific time for technical assistance. The II Morrow technical service staff will gladly assist you.
Please have the following information ready:
System configuration (products, antennas, mounting locations, etc.)
Model No., part number, and serial number
Description of the problem
Efforts made to isolate/solve the problem
Computed Lat/Lon position shown on your Apollo
Local time, UTC time, and date
II Morrow Inc. Technical Service Department 2345 Turner Road S.E. Salem, OR 97302 U.S.A.
U.S.A. Toll Free 800-525-6726 Canada Toll Free 800-654-3415 FAX (503) 364-2138 International (503) 391-3411

To Ensure Trouble Free
Avoid high cockpit temperatures when the aircraft is not in use. Extreme heat shortens the life of any electronic equipment. Periodically check all antenna, power, and ground connections.
The Apollo GX memory is maintained by a lithium battery. The expected service life of this type of battery is from four to six years. This is not a user replaceable item. The lithium battery must be replaced by the factory, an authorized dealer, or service center.
Please read the instructions again for the desired function.
Record as much information as possible, such as where and when the problem occurred, symptoms, and your actions. Record the position sensor data (displayed in SYS mode) for ALL satellites (GPS) and call your II Morrow dealer, Service Center, or the factory. The technician MUST have this information to help you solve the problem.
If You Are Unable To Correct The
Problem Possible Cause Action
Unit does not power on
Open in power supply circuit
Check circuit breaker - reset if necessary Faulty electrical wiring or connection
Contact your dealer to perform electrical system test

Problem Possible Cause Action
No GPS signal reception
Move aircraft out of hangar or away from buildings to provide an unobstructed view of the sky for the antenna Incorrect seed position, time, or UTC differential entered
Check these settings, if necessary in the System Functions If using a wrong antenna: faulty external antenna, wiring, or connections
Contact your dealer to check the antenna and other wiring
Interference Check for GPS L1 interference sources. Contact your dealer or II Morrow tech support. MSG light stays on after power-on. Displayed message is: IN USE SENSOR CANNOT COMPUTE Lat/Lon
The In-Use position sensor is not able to calculate a position
Check for obstructions and connections to the antenna.
The GPS engine may need to be reset. No User waypoints show up on the Map display or the Nearest waypoint list
Runway Limits are set for a value that is too large
Reset the Runway Limits value, see page 12
Waypoint sequencing is erratic
Direct-To entry option setting may not be correct
If you are flying Direct-To, the option should be set to “May Clear”, see page 9
Troubleshooting · Obstructed signal path

Problem Possible Cause Action
Search for nearest waypoints reveals too few or wrong types of waypoints
Incorrect selection of waypoint types to show after search
Check “Airspace Setup” function and verify that the desired waypoint type to search is “ON”, see page 10
Runway Limits are set for a value that is too large
Check the “Identifier and Waypoint Type” section of the Moving Map function on page 6
Check the Runway Limits for too large a value, see page 12 Position fix seems inaccurate
Re-enter seed position Bearing & distance values appear to be wrong
A mistake may have been made in entering the Lat/Lon position for a User waypoint, or the wrong waypoint was selected
Verify that the position of the User waypoint is accurate
Check the FROM and TO waypoints
Wrong bearing and track values
Check Magnetic Var option - select “Automatic” or enter correct value, see page 7 Display blinks Voltage applied to system is too low
Incorrect magnetic variation entered
Check avionics power bus No altitude info Altitude information device was not configured during installation
No altitude info No power to the altitude encoder
Check altitude encoder power
Troubleshooting · Wrong seed position · Check installation configuration

GPS Overview The Global Positioning System (GPS) is a constellation
of 24, or more, satellites in six orbit lanes 10,898 nautical miles above the earth at an inclination angle of about 55 degrees from the equator. Each satellite orbits the earth twice in 24 hours.
The GPS was developed and the satellites launched by the U.S. Department of Defense with the original intent of supplying highly accurate position fix information for military applications. In recent years, commercial applications for the information provided by this system have steadily increased in the civilian sector. Some of the more popular civilian uses of the system include surveying and position fix data recording for civil engineering applications, and a broad range of marine, aviation, and terrestrial navigation applications.
While orbiting the earth, each GPS satellite transmits complex streams of data containing the operational status and orbital location of all the satellites in the system. The Apollo GX receives this data stream and

GPS Navigation

processes the information to determine which satellites are “visible” to the receiver’s antenna. With this determination made, the receiver chooses satellites to calculate a position fix. Using information transmitted from three or more satellites, the unit can calculate latitude and longitude (usually abbreviated Lat/Lon); with four or more satellites, GPS altitude can also be calculated.
The GPS allows a high degree of position fix accuracy. The system can produce a position fix accurate to within less than one meter under ideal conditions. Due to concern for national security, the U.S. Department of Defense introduces constantly changing errors to the transmitted satellite data to degrade the accuracy of the system. Called Selective Availability, this practice limits GPS position fix accuracy to about 100 meters, although the relative position of the satellites to one another, their elevation above the horizon, and other factors can also affect accuracy of the position fix. Under optimal conditions, accuracy can improve to within 10 meters. GPS position fix accuracy is not affected by atmospheric conditions.
GPS altitude is based on a mathematical model of the shape of the earth, the WGS-84 ellipsoid. Including intentional degradation, GPS altitude may differ from barometric altitude by several hundred feet.
GPS Navigation · GPS System · Accuracy

A Altitude (GPS ALT): Altitude, as calculated by the Apollo GX, based upon a mathematical model of the earth’s surface curvature. A substantial difference between this altitude value and altitude referenced to sea level may exist.
Altitude Assist: An aid that provides guidance in descending from one altitude to another. See the Altitude Assist description on page 14 for details.
Almanac: Data transmitted by a GPS satellite including orbit information on all satellites, clock correction, and atmospheric delays.
ARC: A DME arc terminator with the preceding flight plan leg is described as an arc to this waypoint. An ARC waypoint may follow another ARC waypoint.
ATC Ring: On the map display, an artificial ring five nm in diameter is drawn around airports that have a control tower.
Automatic Terminal Information Service (ATIS): Recorded information about weather and other conditions at an airport, periodically updated when conditions change.
Autonav: The function that allows you to set the GX to scroll automatically through selected navigation displays .
Azimuth: an arc, as measured clockwise from true or magnetic north.
B Baro Altitude: Barometric altitude (pressure altitude corrected for local altimeter setting). This altitude should match the altitude displayed on your aircraft altimeter.
Glossary

Bearing (BRG): The direction to any point, usually measured in degrees relative to true or magnetic north. The direction from your present position to your destination waypoint.
C CF: Final approach course Fix. This waypoint type is used when necessary to define a course to the FAF - all VOR DME approaches require a course fix waypoint. A code appended to a waypoint in the database that may not appear on a published map.
Circular Error Probable (CEP): As applied to GPS position fix accuracy, the radius of a circle inside of which there exists a 50 percent chance of being located.
Constellation: A group of stars or objects, such as GPS satellites, in the heavens.
Coordinates: Values for latitude and longitude that describe a geographical point on the surface of the earth.
Course: The planned direction of travel in a horizontal plane.
Course Deviation: A measurement of distance left or right from the desired course of travel.
Course Deviation Indicator (CDI): A graphic indicator of course deviation typically shown as a graduated horizontal bar with an icon indicating the deviation distance left or right of course.
Course Intercept: Similar to an arrival alert, arrival is related to a course or radial to a point. When flying an arc during an approach, the arrival alert is issued when the aircraft is 1 nm/100 kts of intercepting the inbound course. When Vector to Final is selected, or you are executing a procedure turn at the FAF, the course intercept alert occurs when the aircraft has a Track Angle Error 45° and the cross track deviation is 1 nm.
Glossary

Cross Track Deviation: The distance that your are away from your intended course.
FROM
WPT
CTAF: Common Traffic Advisory Frequency.
D Database: A collection of data structured in such a way as to allow quick and convenient access to any particular record or records. The Apollo GX contains a built-in database of waypoints and waypoint information. Users may add waypoints to this database.
Declination: The difference between True North and Magnetic North. A magnetic declination of 19ºE means that Magnetic North is 19ºE of True North.
Declutter: The ability to select the waypoint types and symbols that are displayed on the moving map.
Degree: 1/360th of a circle.
Departure: The first waypoint in the active route.

Desired Track (DTK): The desired course of navigation between a point of origin (FROM) and a destination (TO) waypoint.
Destination: The last waypoint in the active route.
Dilution of Precision (DOP): A merit value for the calculated position based on the geometrical configuration of the satellites used; 3 is considered good, greater than 7 is considered poor. Also called Precision Dilution of Precision or PDOP.
Direct-To: The function or procedure that directs you from your present position to the designated TO waypoint.
Distance: A measure of interval in space. Also referred to as range.
Drift: Displacement from the intended course of travel.
E Elevation: The angle of a GPS satellite above the horizon.
Emergency Search: The function that allows you to immediately navigate to the nearest airport in the case of an emergency.
Ephemeris: A list of accurate positions or locations of a celestial object as function of time.
Estimated Time of Arrival (ETA) - The estimated time of arrival at the TO waypoint in UTC time using a 24 hour clock.
Estimated Time En route (ETE) - The estimated time from your present position to the TO waypoint.
F FAF: Final Approach Fix.
Glossary

FDE: The Fault Detection and Exclusion column refers to the ability to identify and exclude a faulty satellite and still have suitable satellite geometry at that position.
FF: Final Approach Fix. A code appended to a waypoint in the database that may not appear on a published map.
Fix: A geographical location determined by either visual reference or by electronic navigation aids.
Flight Time: Flight Time shows the elapsed time in hours and minutes (00:00 to 99:59) from departure. If the Flight Timer is not started the value will be replaced with dashes. The Flight Timer options are set in the System Functions (see page 8).
Flight Plan: A series of two or more waypoints.
G GDOP: Geometric Dilution of Precision. The relationship between errors in receiver position and time and in satellite range.
Global Positioning System (GPS): Also known as NAVSTAR. A constellation of satellites launched by the U.S. Department of Defense into six orbit lanes (four satellites per plane) at an altitude of 10,898 nm above the earth.
Greenwich Mean Time (GMT): See Universal Time Coordinate (UTC).
Ground Speed (GS): Speed of travel across the ground. In aviation, the relation between ground speed and air speed is affected by the prevailing winds.
H HDOP: Horizontal Dilution of Precision. See Dilution Of Precision.
Glossary

Hold: Waypoint sequencing is disabled or suspended. A hold may be automatically or manually activated. This should not be confused with a “holding pattern.” Pressing the OBS/HLD key suspends waypoint sequencing.
I IAF: Initial Approach Fix.
Identifier: A name, typically abbreviated, assigned to a waypoint. The identifier may consist of numbers and alpha characters, up to six in length. For example, the airport identifier for Los Angeles International Airport is LAX.
IFAF: Initial and Final Approach fix. A combined Initial and Final approach Fix with no intermediate waypoints.
Intersection (INT): A point defined by any combination of courses, radials, or bearings of two or more navigational aids.
K Knot (kt): A unit of speed equal to one nautical mile per hour.
L Latitude (Lat): Any line circling the earth parallel to the equator, measured in degrees, minutes, and seconds north and south of the equator.
LFAC: Landing FACility.
Longitude (Lon): Any line from the north to the south pole, measured in degrees, minutes, and seconds of a circle, east or west of the Prime Meridian (Greenwich, England).
M MA: Missed Approach Point. A code appended to a waypoint in the database that may not appear on a published map.
Glossary

Magnetic North: The region, some distance from the geographic north pole where the earth’s magnetic lines concentrate. A magnetic compass points to the magnetic north.
Magnetic Variation (Mag Var): The angle between the magnetic and true north. At various points on the earth it is different due to local magnetic disturbances. It is shown on charts as isogonic lines marked with degrees of variation, either east or west. These degrees must be added to or subtracted from the true course to get the magnetic course. (Easterly variations are deducted, and westerly variations are added.) The Apollo GX automatically sets magnetic variation to 0 degrees at positions above 70 degrees north or south latitude. See Declination.
MAHP: Missed Approach Hold Point.
MAP: Missed Approach Point.
Map Datum: A mathematical model of the earth used for the purpose of creating navigation charts and maps. The Apollo GX uses the WGS-84 map datum.
MESA: Minimum En route Safe Altitude is the highest MSA for every point between the aircraft present position and the “TO” waypoint with a 5 nm buffer around the course.
Meter (m): A metric distance measurement equal to 39.37 inches.
Minute: 1/60th of a degree.
MSA: Minimum Safe Altitude. The elevation of the highest obstruction near the aircraft plus a 1,000 or 2,000 foot buffer added for safety. In non-mountainous terrain, a 1,000 foot buffer is added. In mountainous terrain, a 2,000 foot buffer is added. The result is rounded to the nearest 100 feet.
Glossary

N Nautical Mile (nm): A distance measurement equal to 6,076 feet, or 1.15 statute mile. One nautical mile is also equal to one minute of latitude.
NAVSTAR: The name given to GPS satellites formed from the acronym for NAVigation System with Time And Ranging.
Non-Directional Beacon (NDB): A low frequency/medium frequency navigation aid sending non-directional signals that can be used for navigation.
O OBS: Omni-Bearing Selector.
P Parallel Track Offset: A course that is parallel to the designated course, but offset to the right or left by a given distance.
PDOP: Position Dilution of Precision. See Dilution of Precision.
PRN: GPS satellite Pseudo-Random Numbers are used to uniquely identify satellites. This is different than the SVN (Space Vehicle Number, or satellite serial number). When excluding satellites from the RAIM Prediction , use the PRN number found on the NOTAMs and NANUs, not the SVN.
R Radial: Any of the 360 magnetic courses from a VOR or similar navigational aid, beginning at the navigational aid and proceeding outward in a straight line.
RAIM: Receiver Autonomous Integrity Monitoring. A method of predicting possible system accuracy errors that may be caused by bad satellite data. The RAIM algorithm requires that more satellites are available and usable than required for a normal GPS position fix.
Range: The distance from the present position to a destination waypoint.
Glossary

Relative Bearing Indicator: The Relative Bearing Indicator is an arrow next to the Bearing value that indicates an approximate bearing to a waypoint or airspace relative to the aircraft’s current track when your current ground speed is more than 5 knots.
RW: Runway Fix. A code appended to a waypoint in the database that may not appear on a published map.
S Second: 1/60th of a minute of a degree.
Seed Position: A latitude and longitude position fix approximately equal to the current position that the Apollo GX uses to determine the location of available satellites from which signals may be received.
Selective Availability (SA): The degradation of accuracy of GPS position fix data by the United States Department of Defense for civilian use.
Space Vehicle (SV): A GPS satellite.
Statute Mile: A distance measurement equal to 5,280 feet or 0.87 of a nautical mile.
T Three-dimensional (3D) Position Fix: A position fix defined by latitude, longitude, and altitude.
Glossary

Track (TRK): The imaginary line that the flight path of an airplane makes over the earth.
Track Angle Error (Tae)
DTK
FROM
WPT
Track Angle: The angle of your actual direction of travel. Track angle is computed using the magnetic variation at the Present Position.
Track Angle Error (TAE): The difference between the Desired Track and the Track Angle (Dtk - Trk = Tae). A letter is shown next to the Track Angle Error value showing the direction of error in reference to the current Track.
True North: Geographic north, at the earth’s north pole.
Tower (TWR): Airport tower communication frequency.
U UNICOM: The radio frequencies assigned to aeronautical advisory stations for communication with aircraft. Unicoms may provide such airport information as active runway, wind direction and velocity and other conditions of importance to pilots.
UTC (Universal Time Coordinate): Greenwich Mean Time, or the time at the Prime Meridian in Greenwich, England. Also referred to as Zulu time.
Glossary · North · Present Position

UTC Differential: The difference in time between that at the present position and UTC.
UTM (Universal Transverse Mercator map projection system): Also known as Military Grid Coordinates, the UTM grid consists of 60 north-south/east-west zones, each six degrees wide in longitude.
V VFR: Visual Flight Rules.
VOR: Very High Frequency Omni-directional range. A navigational aid that transmits signals such that a receiver can indicate its current radial or bearing from the transmitter.
VHF: Very High Frequency. The range of frequencies between 30 and 300 MHz.
VNAV: Vertical Navigation. See Altitude Assist.
W Waypoint: A navigation fix used in area navigation and defined by latitude and longitude coordinates.
Glossary

Glossary

CDI reverse sensing 9-22 Change approach 6-22 Cleaning 13-2 Clear exclusion list 9-35 Clear flight plan wpts 6-17 Close 4-11, 8-3 Close altitude 8-4 Com
D Database 5-1 - 5-16 Database expired 8-13 Database invalid 8-13 Database message 11-5 Database test 11-4 Datacard 5-16 Date and Time 7-11 Delete flight plan 6-18 Density altitude 7-21 Descent rate 3-17 Description
Headphone level 10-12 Info 10-9 Intercom squelch 10-10 Key 1-8 Noise level 10-10 Sidetone level 10-12 Signal strength 10-10 Comm radio
Cross track distance 3-6 Moving map 4-1 Nav display 3-4 Nav terms 3-1 To-From switching 3-6 Waypoint 11-7 Desired heading 7-21 Desired track 3-6 Diamond 3-1 Direct-To . 2-7, 3-31 - 3-32, 6-9, 7-8, 9-18 May Clear 2-7, 7-9 Never Clears 7-9 OBS 3-35 Disable approach 6-23 Display 1-2
Test 11-1 Comm Radio 10-1 - 10-12
Auto stack list 10-6 Emergency channel 10-8 Frequency abbreviations· · 10-4 Intercom 10-8 Monitoring frequencies · · 10-3 Recalling frequencies · · · 10-4 Selecting frequencies · · · 10-2 Squelch 10-8 Stuc mic 10-9 User frequencies 10-7 Weather channel 10-7 Comments
Flashing 1-iv Test 7-14, 11-11 Display brightness 7-14 Distance off track 3-5 Distance to waypoint 3-25 DME Arc . . 3-24, 8-11 - 8-12, 9-26, 9-63, 9-87, 12-1 DTK Up 4-5 Duplicate names 2-4, 5-4 E Edit owner information 7-16 EEPROM 11-4 Elevation 5-6 E-Mail 1-ii Emergency approach 9-35
See alsoFlight plan comments See alsoWaypoint comments Continue flight plan 6-21 Controls 1-3 Conventions 1-iv Copy flight plan 6-16 Countdown timer 3-22, 8-14 Courrse intercept 8-10 Create User waypoint 4-29 Creeping Line Pattern 4-23 Cross track distance 3-6 Crossing FAF 9-12 Current time 2-1 Customizing Nav pages 7-2
Index

Emergency channel 10-8 Emergency search 3-9 Empty TO waypoint 8-4 En route operation 9-30 Enable approach 6-23, 9-8 Encoder altitude 3-15 Encoding altimeter 7-20 Ending Altitude 3-18 Enroute 9-1, 9-5 Error messages 8-3 Estimate ground speed 6-16 Estimated fuel flow 6-17 Estimated time enroute 3-4, 6-7 - 6-8 Estimated time of arrival . . 3-9, 6-7 ETA to waypoint 3-25 ETE to waypoint 3-25 Examples
Estimated fuel flow 6-17 Hold 6-18 Inserting legs 6-11 Leg info 6-6 Manual leg 6-9 Manual leg select 9-19 Memory failure · · · 8-12, 11-3 New waypoint 3-33 Options 6-14 Pages 6-1 Reactivate 6-15 Rename 6-15 Rev activate 6-15 Reverse flight plan 6-17 Saving Active plan 6-24 Sequencing 6-5 Waypoint sequencing · · · 9-20 Flight simulator 12-1 - 12-4
Approach 9-37 - 9-76 Direct-To 3-32 DME arc 9-63 Procedure turns · · · 9-66, 9-68 Exclude satellite 9-34 Expanding Square Pattern . . . 4-26 External Annunciators . . 1-3, 11-10 F Factory 13-1 FAF 9-10, 9-12 FCC Notice 1-iii Features 1-9 Find waypoint 2-1, 2-6 Flight plan 6-1 - 6-26
Operation 12-4 Starting 12-2 Flight time 3-9, 7-8 Flip/Flop key 1-8 Frequency abbreviations 10-4 From 6-19 FROM waypoint 3-6 From/To/Next 3-26, 3-29 From-To distance 3-6 Fuel 5-7 - 6-8 Fuel endurance 7-22 Fuel flow 7-20 Fuel info 7-22 Fuel Measure 7-13, 7-24 Fuel range 7-22 Fuel sensor 7-20 Fuel used 7-22 Fuel warning 7-23 Fuel/Air Data sensor 7-20 G Glide path 3-17 Glide slope 3-17 Glossary 15-1 - 15-12 GPS 7-19, 14-1
Activate 6-14 Activating 2-9 Active 6-2 Clear waypoints 6-17 Comments 6-23 Continue 6-21 Copy plan 6-16 Creating 2-8, 6-2 Delete plan 6-18 Deleting legs 6-12 Editing 6-10 - 6-11 Estimate ground speed · · 6-16
Accuracy 14-2
Index

Antenna 11-12 Azimuth 7-18 Communication failure· · · 8-5 Elevation 7-18 Error 8-5 Failure 8-4 Health 7-17, 11-11 Introduction 14-1 - 14-2 Position 3-21 Reset 7-19 Satellite failure 9-32 Satellites 7-18, 11-12 Sensor 7-17 Signal strength 11-11 Signal Strength 7-18 Time 7-17 GPSS 3-37 Grid Line Display 4-15 Ground speed 3-7 GX50 description 1-2 GX55 description 1-2 GX60 description 1-2 H Headphone level 10-12 Heat 13-2 Help! 13-1 History of Revisions 1-ii Hold 3-19, 3-30, 6-18 Hold altitude 3-16, 8-8 Hold buffer 3-16 Holding at To wpt 8-11 Holding patterns. . 6-19, 9-24 - 9-25 HSI 3-17 I IAF 9-10 IFR output tests 11-8 II Morrow 13-1 ILS runway 5-6 Indicated air speed 7-21 Info 3-14, 5-1, 5-5, 6-23, 8-3 Info 28, 37, 40, 60, 62, 98 10-6 INSIDE 8-4
INT smart key 1-6 Intercom 10-8 Intercom level 10-11 Intercom squelch 10-10 Intersection info 5-2 K Key 1-4
APT 1-6 Database 1-5 Direct-To 1-5 Flight Plan 1-5 Hard 1-iv Info 1-4 INT 1-6 List 1-6 Map 1-5 Map orient 1-7 Map reference 1-7 Map setup 1-7 Message 1-5 Nav 1-4 NDB 1-6 Nearest 1-4 NRST 3-10 Route line 1-7 RTE 4-4 Scan 1-7, 4-3 Select 1-4 Skip 1-6, 11-1 Smart 1-iv System 1-6 User 1-6 VOR 1-6 XIT 1-8 Keys
Hard 1-4 Smart 1-5 Knobs 1-iv L Large knob 1-3 Lat/Lon position 5-8 Lat/Lon reference 11-7
Index

Lat/Lon units 7-4 Left engine fuel 7-23 Leg distance 3-6 List key 1-6 Load approach 6-22, 9-7 Load destination 9-6 Local altimeter 3-15 Localizer 3-39 - 3-40 Low fuel 8-8 M Magnetic heading 7-20 - 7-21 Magnetic variation 7-7, 8-13 Magnetic wind direction 7-22 Manual leg activation 6-9 Manual prediction 9-33 Manuals 1-ii Map 5-7 Map reference 4-6 Map setup 1-7, 4-4 Map Setup
Map & Nav info 4-3 Orientation 4-5 Route line 4-4 Scale 4-3 Setup 4-4 Multiple facilities 5-4
See alsoDuplicate names N Nav page choices 7-5 Nav superflag tests 11-9 Nav Valid flag tests 11-9 Navigation 3-1, 7-1
Displays 3-1 Empty To waypoint 8-4 Home page 3-1 Pages 3-3 - 7-4 Programmable pages 7-2 Terms 3-1 NDB Info 5-2 NDB smart key 1-6 Nearest waypoint. . 2-6, 3-12 - 4-13, 5-9, 9-36, 10-6 Nearest waypoint search . . 3-9, 5-1 Never clear 7-9 Noise level 10-10 Non-volatile RAM test 11-3 North Up 4-5 NRST 1-2, 1-4, 2-6, 3-9 - 3-10, 3-12, 4-6, 4-13, 9-36, 13-3 NVRAM 11-4 O OBS 3-35, 8-12, 9-18 Offset distance 3-17 Ordering Information 1-ii ORI key 1-7 Outside air temperature 7-21 Owner information 7-15 Owner message 11-2 P Parallel Line Pattern 4-21 Parallel track 3-19, 3-21
Search and Rescue 4-16 Map waypoint keys 1-6 Mark position 4-28 May clear 7-9 May Clear 2-7 Measurement units 7-6 Memory failure 8-13, 11-1 Memory loss or failure 8-12 Memory test 11-2, 11-4 Message 8-1 - 8-14 Microphone 10-9 Minimum enroute safe altitude . 3-8 Minimum safe altitude 3-8 Misc sensors 7-20 Missed approach 9-13 Missed approach point 9-12 Monitor frequency 10-3 Moving map 2-10
Setup 2-10 Moving Map 2-10, 4-1 - 4-32
Controls 4-2 Full screen 4-1 Idents 4-6
Approach conflict 8-6
Index

In Use 3-19 Standby 3-19 Part numbers 1-ii Password 7-16 Pattern 4-20 PDOP 3-21 Phase II Approach 9-89 Phase III Approach 9-90 Photocell 1-2 Power knob 1-3 Power Up 2-1 Pressure altitude 7-21 Procedure turn 4-4 Procedure Turns . 9-21 - 9-22, 9-66, 9-68 Programmable Nav pages 7-2 R RAIM 8-5, 9-29, 9-33
Runway length 3-12, 5-11 Runway limits 3-12 Runway surface 3-13 S Save active flight plan 6-24 Scan 4-3 Scan key 1-7 Search and Rescue 4-14
Basic Grid 4-16, 4-18 Create user waypoint · · · 4-29 Creeping Line Pattern · · · 4-23 Expanding Square 4-26 Grid Line Display 4-15 Map Setup 4-16 Mark position 4-28 Parallel Line Pattern 4-21 Sectional Chart Grid 4-19 Select pattern 4-20 Setting up a search pattern 4-32 US Grid Type 4-15 Search around ref wpt 3-10 Sectional Chart Grid 4-19 Seed Position 11-5 Select a waypoint 2-1, 2-3 Select different approach 9-17 Setting measurement units 7-6 Setting up a search pattern . . . 4-32 Sidetone level 10-12 Skip 1-6, 11-1 Small knob 1-3 Software memory test 11-2 Software version 7-12 SOON 8-3 Sort waypoints 2-2 Special use airspace 3-13 Specifications 1-9 - 1-12 Speed 7-22 Squelch knob 1-3 Standby 3-20 Start up displays 11-1 - 11-12 Startup bypass 11-1 Storing a waypoint 2-5 Stuck microphone 10-9
Clear exclusion list 9-35 Exclude satellite 9-34 Manual prediction 9-33 RAIM alarm 9-32 Range 3-4 Rate of climb 7-21 Reactivate 6-15 Recall frequency 10-4 REF key 1-7 Reference position 11-7 Reference Waypoint 3-10, 5-10, 11-6 Relative Bearing Indicator 3-3 Remove unit from aircraft . . . 12-2 Rename flight plan 6-15 Repeat approach 9-16 Replace unit in aircraft 12-2 Reserve fuel 7-23 Rev Activate 6-15 Reverse flight plan 6-17 RF signal strength 10-10 Right engine fuel 7-23 RNAV 5-16, 9-1 Route line 4-4 Route line key 4-4 RTE key 1-7, 4-4 Runway info 5-7
Index

Sunset/Sunrise time 5-8 Symbol
User waypoint info 5-3 User Wpt
Triangle 3-5 System 7-1 - 7-24
Update position 5-12 USR smart key 1-6 UTC time 3-9, 11-5 UTM 7-4 V VDI 3-17 VDI flag tests 11-10 VDI output tests 11-9 Vector to Final 9-27 Vertical deviation 3-17 VNAV 3-14 Volume knob 1-3 VOR Info 3-39, 5-2 VOR smart key 1-6 W Waypoint
Navigation Info 7-1 System Info 7-11 T Technical assistance 13-1 Terminal operation 9-30 Tips 6-26 To 6-19 TO waypoint 2-4, 3-6, 4-1, 8-9 TO-FROM flag tests 11-8 Total fuel 7-23 Track angle 3-7 Track angle error 3-7 Track History 4-8
Strategy 4-8 Track Up 4-5 Transition 9-2 Transmit Mic 10-11 Troubleshooting 13-1 - 13-4 True air speed 7-21 True air temperature 7-21 True north 7-7 True wind direction 7-22 TSO C129 overlay 9-77 Turn anticipation 3-36 Turn rate 7-21 U Underline 1-iv Units 7-6 Unload approach 6-22 Update User Wpt 5-12 US Grid Type 4-15 User database memory failure . 11-3 User frequency 10-7 User waypoint
Airport info 5-1 Approach 9-77 Arrival 8-9, 9-2 Auto OBS crossing 8-12 Comment 5-8 Comments 5-14 - 5-15 Create 5-9 - 5-10 Database 5-1 - 5-16 Destination 6-23 FROM 3-26 From/To/Next 3-26 Information 2-4, 5-1, 5-3 Intersection info 5-2 Last used 3-11 LOC-DME 9-69 Map 5-7 Map identifier 4-2 Naming conventions 9-87 NDB info 5-2 Next 3-29 Scan 4-3 Selection 2-1 Sequencing · · · 6-5, 9-20, 9-24 To 3-28, 8-11
Create 5-9 - 5-10 Delete 5-12 Information 5-3 Modify 5-13
Index

Type 1-6, 4-6 Update User 5-12 User info 5-3 VOR info 5-2 Waypoint alert 8-10 Weather channel 10-7 Web Page 1-ii Wind direction 7-22 Wind speed 7-22 X XIT key 1-8
Index



© 2001 by UPS Aviation Technologies, Inc.
2345 Turner Rd., S.E. Salem, OR 97302
U.S.A.
Phone 503.581.8101
800.525.6726 In Canada 800.654.3415

Part #560-0961-03 · July 2001
Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Unit does not power on | Open in power supply circuit | Check circuit breaker - reset if necessary | p.298 |
| Unit does not power on | Faulty electrical wiring or connection | Contact your dealer to perform electrical system test | p.298 |
| No GPS signal reception | Obstructed signal path | Move aircraft out of hangar or away from buildings to provide an unobstructed view of the sky for the antenna | p.299 |
| No GPS signal reception | Incorrect seed position, time, or UTC differential entered | Check these settings, if necessary in the System Functions | p.299 |
| No GPS signal reception | If using a wrong antenna: faulty external antenna, wiring, or connections | Contact your dealer to check the antenna and other wiring | p.299 |
| No GPS signal reception | Interference | Check for GPS L1 interference sources. Contact your dealer or II Morrow tech support. | p.299 |
| MSG light stays on after power-on. Displayed message is: IN USE SENSOR CANNOT COMPUTE Lat/Lon | The In-Use position sensor is not able to calculate a position | Check for obstructions and connections to the antenna. The GPS engine may need to be reset. | p.299 |
| No User waypoints show up on the Map display or the Nearest waypoint list | Runway Limits are set for a value that is too large | Reset the Runway Limits value, see page 12 | p.299 |
| Waypoint sequencing is erratic | Direct-To entry option setting may not be correct | If you are flying Direct-To, the option should be set to “May Clear”, see page 9 | p.299 |
| Search for nearest waypoints reveals too few or wrong types of waypoints | Incorrect selection of waypoint types to show after search Runway Limits are set for a value that is too large | Check “Airspace Setup” function and verify that the desired waypoint type to search is “ON”, see page 10 Check the “Identifier and Waypoint Type” section of the Moving Map function on page 6 Check the Runway Limits for too large a value, see page 12 | p.300 |
| Position fix seems inaccurate | Wrong seed position | Re-enter seed position | p.300 |
| Bearing & distance values appear to be wrong | A mistake may have been made in entering the Lat/Lon position for a User waypoint, or the wrong waypoint was selected | Verify that the position of the User waypoint is accurate Check the FROM and TO waypoints | p.300 |
| Wrong bearing and track values | Incorrect magnetic variation entered | Check Magnetic Var option - select “Automatic” or enter correct value, see page 7 | p.300 |
| Display blinks | Voltage applied to system is too low | Check avionics power bus | p.300 |
| No altitude info | Altitude information device was not configured during installation | Check installation configuration | p.300 |
| No altitude info | No power to the altitude encoder | Check altitude encoder power | p.300 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.