EN
Lexmark logo
Official user manual

Lexmark Optra E312

116 pages·4.6 MB·Printer·PDF·ENDEFRITNLJA
Lexmark Optra E312
Table of Contents 31 sections About your printer · Model specifications · Performance · Print quality · … ShowHide
Page 1 of the Lexmark Optra E312 user manual — www.lexmark.com
Page 1 · click to enlarge
Page 1
Lexmark Optra E312 diagram (page 1)
Fig. 1

Optra E312

User’s Guide

June 2000

www.lexmark.com

Page 2 of the Lexmark Optra E312 user manual
Page 2 · click to enlarge
Page 2
EditionJune 2000

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.

Lexmark, MarkVision and Optra are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. FontVision is a registered trademark of Lexmark International, Inc. Operation ReSource is a service mark of Lexmark International, Inc.

Macintosh is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. TrueType is a trademark of Apple Computer, Inc.

PCL® is a registered trademark of the Hewlett-Packard Company. PCL 5 and PCL 6 are Hewlett-Packard Company’s designations of a set of printer commands (language) and functions included in its printer products. This printer is intended by Lexmark International, Inc. to be compatible with the PCL 5 and PCL 6 languages. This means the printer recognizes PCL 5 and PCL 6 commands used in various application programs, and that the printer emulates the functions corresponding to the commands.

Details relating to compatibility are included in the Technical Reference.

Other trademarks are the property of their respective owners.

© Copyright 2000 Lexmark International, Inc. All rights reserved.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and in applicable FAR provisions: Lexmark International, Inc., Lexington, KY 40550.

Page 3 of the Lexmark Optra E312 user manual
Page 3 · click to enlarge
Page 3
Page 3 of the Lexmark Optra E312 user manual
Page 6 of the Lexmark Optra E312 user manual — About your
Page 6 · click to enlarge
Page 6

About your

printer

The Optra E312 printer combines the quality of a laser printer with a conveniently small footprint for a perfect fit.

Lexmark Optra E312 — About your diagram (page 6)
Fig. 2 · About your

With its easy setup, you’ll be printing in no time. Use this CD for information on:

  • installing printer memory options
  • installing printer drivers
  • loading paper
  • solving printing problems
  • understanding the indicator light sequences
  • maintaining your printer

We’d like to keep you informed of upgrades for your printer and new products as they become available, so be sure to fill out the printer registration card and mail it in.

Page 7 of the Lexmark Optra E312 user manual — Model specifications
Page 7 · click to enlarge
Page 7

Model specifications

The information included on this CD applies to both the Lexmark™ Optra™ E312 and E312L printers. The differences between these two models are outlined in the following table.

ItemOptra E312Optra E312L Base memory4MB2MB Maximum memory68MB66MB EmulationsPostScript Level 2, PCL 6 and PPDSPCL 6 and PPDS Machine type and model4044-2014044-2Lx Ship with print cartridge yield (at approximately 5% coverage)6,000 pages (Standard)1,500 pages (Starter) Reorder print cartridge yield6,000 pages (Standard)6,000 pages (Standard)
Lexmark Optra E312 — Model specifications diagram (page 7)
Fig. 3 · Model specifications
Page 8 of the Lexmark Optra E312 user manual — Performance
Page 8 · click to enlarge
Page 8

Performance The Optra E312 printer prints up to 10 pages per minute for quick job turnaround. It comes with 4MB of memory, expandable to 68MB to print complex jobs quickly. You can also install an optional flash memory card to store forms, macros and downloaded fonts. PostScript Level 2 and PCL 6 emulation datastreams give you application flexibility.

Print quality Selectable print resolution to optimize printer/job performance: true 600 x 600 dpi resolution for crisp images and graphics; 1200 Image Quality to print sharper scanned or bitmapped print images; 300 dpi with the Toner Saver setting selected from your printer driver to conserve toner when printing drafts.

Ease of use A variety of fonts for printing flexibility: 75 PCL scalable fonts (45 LaserJet-compatible scalable fonts plus 30 additional PCL scalable fonts), 75 PostScript scalable fonts (39 Optra-compatible scalable fonts plus 36 PostScript scalable fonts), FontVision™ font manager utility with 110 TrueType fonts and world- class international font support, including the new euro currency symbol.

The MarkVision™ printer utility that ships with your printer lets you:

  • view and change your printer settings
  • view your operator panel status
  • view printer error messages
  • use online Help
Page 9 of the Lexmark Optra E312 user manual — Performance
Page 9 · click to enlarge
Page 9

3 Paper guides Front View 2 Paper support 1 Automatic paper feeder

Lexmark Optra E312 — Performance diagram (page 9)
Fig. 4 · Performance

4 Manual sheet feeder

Use the:When you want to: 1 Automatic paper feederLoad paper/other media (up to 150 sheets of paper or 10 sheets of other media). 2 Paper supportStack media in the automatic paper feeder. 3 Paper guidesAdjust the width of the paper in the automatic paper feeder. 4 Manual sheet feederLoad a single sheet of paper/other media. Use for transparencies, labels, envelopes and card stock. 5 Paper supportStack media in the paper output bin. 6 Paper guidesAdjust the width of the paper in the manual sheet feeder. 7 Indicator lightsCheck the status of your printer. For information, see Printer status information. 8 Paper output binStack printed documents, face down. 9 Front output doorFeed media straight out the front of the printer. Use the front exit when printing on card stock. To minimize curl, use when printing labels, envelopes and transparencies.

Printer Features · 5 Paper support · 6 Paper guides

Page 10 of the Lexmark Optra E312 user manual — Performance
Page 10 · click to enlarge
Page 10
Lexmark Optra E312 — Performance diagram (page 10)
Fig. 5 · Performance

11 USB connector 10 Printer cable connector

12 Power cord connector

Use the:When you want to: 10 Printer cable connectorConnect your computer to the printer’s parallel port with a parallel interface cable. 11 USB connectorConnect your computer to the printer’s USB port with a Universal Serial Bus cable. 12 Power cord connectorConnect your printer to a properly grounded wall outlet with a power cord. 13 Power switchTurn your printer on or off.
Lexmark Optra E312 — Performance diagram (page 10)
Fig. 6 · Performance

Rear view · 13 Power switch

Page 11 of the Lexmark Optra E312 user manual — Performance
Page 11 · click to enlarge
Page 11

Indicator lights The operator panel has 6 lights and 1 button. Different light sequences provide status, attendance and service information.

Lexmark Optra E312 — Performance diagram (page 11)
Fig. 7 · Performance

Depending on the light sequence, briefly (approximately one second) pushing Press Button activates different printer functions, such as restarting the printer, printing data or displaying an error code.

Press and hold Press Button for 3 seconds only when you want to reset the printer to the user defaults. When resetting the printer to the user defaults, all print job data is lost.

The different light sequences are explained in the Troubleshooting chapter. Use MarkVision or your software application driver to change printer settings such as paper source, paper size and orientation.

To set up your printer, go to the next chapter.

Page 12 of the Lexmark Optra E312 user manual — sources
Page 12 · click to enlarge
Page 12

Other information

In addition to this User’s Guide CD, Lexmark offers other sources of information about your printer or about Lexmark products and services.

sources

Online documents The Drivers, MarkVision and Utilities CD that was shipped with your printer contains several online documents. Refer to the booklet that came with the CD for launching instructions. Once you have launched the CD, click the View Online Documentation icon to display a list of the available documents. All online documents are in English only. The CD includes:

  • Getting Started with MarkVision, which provides step-by-step instructions for installing MarkVision for Windows 95, Windows 98, Windows 2000 and Windows NT 4.0. It also describes some of the most popular MarkVision features.
  • Card Stock & Label Guide , which provides detailed information about selecting media appropriate for your printer.
  • A Technical Reference, which includes information about printer languages and commands, interface specifications and printer memory management.
Page 13 of the Lexmark Optra E312 user manual — Other information sources
Page 13 · click to enlarge
Page 13
Page 13 of the Lexmark Optra E312 user manual — Other information sources
Page 14 of the Lexmark Optra E312 user manual — 1 What’s in the box
Page 14 · click to enlarge
Page 14

The basics

Lexmark Optra E312 — The basics diagram (page 14)
Fig. 8 · The basics

What’s in the box 1 Remove the printer and all accessories from the packaging carton.

Save the carton and packing materials in case you need to repack the printer for service or storage.

Lexmark Optra E312 — The basics diagram (page 14)
Fig. 9 · The basics

2 Make sure you have the items listed below:

– Setup Guide and printer registration card – printer – print cartridge – power cord – User’s Guide CD – Drivers, MarkVision and Utilities CD

If you need help during setup, or if any items are missing or damaged, refer to the registration card for the designated Lexmark phone number for your country.

3 Place the printer on a flat, stable surface in a well-ventilated area near your workstation.

Do not place the printer:

– in direct sunlight – near heat sources or air conditioners – in dusty or dirty environments

1 What’s in the box

Page 15 of the Lexmark Optra E312 user manual — 2 Chapter 1: The basics
Page 15 · click to enlarge
Page 15

Installing the print

1 Use the finger tab to pull down the printer cover.

cartridge

2 Unpack the print cartridge.

3 Holding the cartridge level, pull out the sealing tape.

2 Chapter 1: The basics

Page 16 of the Lexmark Optra E312 user manual — 3 Installing the print cartridge
Page 16 · click to enlarge
Page 16

4 Gently shake the cartridge to distribute the toner evenly.

5 Insert the print cartridge:

a Slide the print cartridge down between the

print cartridge slots.

b Gently push down on the cartridge until it

drops into place.

6 Close the printer cover.

3 Installing the print cartridge

Page 17 of the Lexmark Optra E312 user manual — 4 Chapter 1: The basics
Page 17 · click to enlarge
Page 17
Lexmark Optra E312 — Connecting the printer to your computer diagram (page 17)
Fig. 10 · Connecting the printer to your computer
  • Characters appear light or blurred.
  • Make sure you removed the sealing tape from the print cartridge.
  • Replace the print cartridge.

Printer seems to be printing, but pages are blank.

  • The print cartridge may be out of toner. Replace the cartridge.
  • The print cartridge may be defective. Replace the cartridge.
  • Make sure you removed the sealing tape from the print cartridge.

Jobs are not printing and the Error light is on solid.

Connecting the

To print from software loaded on your computer, your printer needs to be connected to your computer with either a parallel interface cable or a USB cable.

printer to your

computer

Using a parallel

Your printer requires an IEEE-1284 compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft). If you use something other than an IEEE-compliant cable, you may not be able to use all of your printer’s functions.

interface cable

1 Make sure your printer is turned off.

Lexmark Optra E312 — interface cable diagram (page 17)
Fig. 11 · interface cable

2 Plug the parallel interface cable into the connector on the back of the printer.

3 Push the metal clips toward the plug until they snap in the notches on the plug.

4 Attach the other end of the parallel cable to your computer.

5 Turn on the printer.

4 Chapter 1: The basics

Troubleshooting Tips

Page 18 of the Lexmark Optra E312 user manual — 5 Connecting the printer to your computer
Page 18 · click to enlarge
Page 18

Using a USB cable If you are connecting your printer to a PC with a USB (Universal Serial Bus) cable, we recommend Lexmark part number 12A2405 (2 m). If you use something other than this cable, you may not be able to use all of your printer’s functions.

If you are using Windows 2000:

1 Make sure your computer and printer are turned off.

2 Connect the USB cable to the port on the back of your computer.

3 Connect the other end of the cable to the USB port on the back of your printer.

4 Turn on your computer and your printer.

5 When the Found New Hardware Wizard screen appears, select Cancel to close the wizard.

6 Insert the Drivers, MarkVision, and Utilities CD that came with your printer and select Start.

7 From the Start menu, select Run, then click Browse.

8 Click on the My Computer shortcut in the Browse window, double-click on the CD icon, and double-click on the setup application (setup.exe).

9 Click OK to start the printer driver installation program.

10 Follow the installation instructions in the printer drivers dialog box.

11 In the Print to the following port check box, select the USB port that best describes the order you’ve connected USB printers to your computer (i.e., the first USB printer is USB001, the second USB002, and so on).

5 Connecting the printer to your computer

Page 19 of the Lexmark Optra E312 user manual — 6 Chapter 1: The basics
Page 19 · click to enlarge
Page 19

12 When you finish, exit the setup program and remove the CD from your computer.

If you are using Windows 98:

1 Make sure your computer and printer are turned off.

2 Connect the USB cable to the port on the back of your computer.

3 Connect the other end of the cable to the USB port on the back of your printer.

4 Turn on your computer and your printer.

5 When the Add New Hardware Wizard screen appears:

a Select Next to begin searching for the new

drivers.

b Select Next to use search for the correct driver.

c Make sure the Floppy disk drives, CD-ROM

drive and Microsoft Windows Update check boxes are cleared, and select the Specify a location check box.

d Insert the Drivers, MarkVision, and Utilities CD

that came with your printer and select Browse.

e Double-click the letter of your CD drive, then

double-click the Win98USB folder beneath it.

f Highlight the language you wish to install USB support for, then click OK.

g Select Next.

h Select Next again.

i When the hardware is loaded, click Finish.

The printer driver installation program automatically launches after a few moments.

6 Chapter 1: The basics

Page 20 of the Lexmark Optra E312 user manual — 7 Connecting the printer to your computer
Page 20 · click to enlarge
Page 20

6 Follow the installation instructions in the printer drivers dialog box.

7 In the Print to the following port check box, select the USB port that contains the name of the printer you are currently installing as your default printer port.

8 When you finish, exit the setup program and remove the CD from your computer.

9 Restart your computer.

Lexmark Optra E312 — Connecting the printer to your computer diagram (page 20)
Fig. 12 · Connecting the printer to your computer
  • Make sure the parallel cable or USB cable is firmly plugged in at the back of the printer.

You are connected to the USB port, but the printer will not print.

  • Make sure you are using Windows 98 or Windows 2000.

7 Connecting the printer to your computer

Troubleshooting Tips

Page 21 of the Lexmark Optra E312 user manual — 8 Chapter 1: The basics
Page 21 · click to enlarge
Page 21

For Macintosh users:

Lexmark Optra E312 — Connecting the printer to your computer diagram (page 21)
Fig. 13 · Connecting the printer to your computer

1 Make sure the printer power is Off (O) and the printer power cord is unplugged from the electrical outlet.

2 Connect the end of the USB cable to the port on your computer.

3 Align and plug the other end of the USB cable into the port on the back of your printer as shown.

4 Plug the printer in.

5 Turn the printer on.

6 Launch the Drivers, MarkVision, and Utilities CD to install the necessary items. Instructions to launch the CD are in the CD booklet.

7 Restart the computer.

8 Open the Apple Extras folder.

9 Open the Apple LaserWriter Software folder.

10 Open the Desktop Printer Utility application.

11 The New Desktop Printer screen displays.

12 Select Printer (USB) from the list and click OK.

13 In the USB Printer Selection box, click Change.

The USB printer dialog box displays.

14 Select Optra E312 and click OK.

The previous screen displays. Notice the new printer icon.

8 Chapter 1: The basics

Page 22 of the Lexmark Optra E312 user manual — 9 Connecting the printer to your computer
Page 22 · click to enlarge
Page 22

15 In the PostScript Printer Description (PPD) File box, click Auto Setup.

Wait for the information to process.

The previous screen displays. Notice the new printer icon.

16 Click Create.

A window appears for you to name the printer.

17 Type in the name of the printer or accept the default name.

18 Click Save.

19 Quit the Desktop Printer Utility application.

The printer icon displays on your Desktop.

20 Click the new desktop printer icon.

The Printing menu appears on the menu bar.

21 Scroll down in the Printing menu and select Set Default Printer.

A dark line appears around the printer in the printer icon to indicate it is selected as the default printer.

ProblemWhat to do:

Auto Setup fails in the PostScript Printer Description (PPD) File box

  • Re-install the printer PPD from the CD.

9 Connecting the printer to your computer

Troubleshooting Tips

Page 23 of the Lexmark Optra E312 user manual — 10 Chapter 1: The basics
Page 23 · click to enlarge
Page 23

Loading paper

You can load paper in the automatic paper feeder, which holds up to 150 sheets, or the manual feeder, which holds 1 sheet at a time.

Lexmark Optra E312 — Loading paper diagram (page 23)
Fig. 14 · Loading paper

1 To print from the automatic paper feeder, extend the paper support.

2 Before loading paper, flex the sheets back and forth to loosen them, then fan them.

3 If the paper has a preferred print side, insert the paper with the print side facing you.

Lexmark Optra E312 — Loading paper diagram (page 23)
Fig. 15 · Loading paper

If you are loading letterhead paper, insert letterhead with the top of the page pointing down.

10 Chapter 1: The basics

Page 24 of the Lexmark Optra E312 user manual — 11 Loading paper
Page 24 · click to enlarge
Page 24

4 Slide the paper guides against the edges of the paper.

Lexmark Optra E312 — Loading paper diagram (page 24)
Fig. 16 · Loading paper

5 Extend the paper support on the paper output bin.

Lexmark Optra E312 — Loading paper diagram (page 24)
Fig. 17 · Loading paper

6 Select the paper size from your software application.

7 Start your print job.

11 Loading paper

Page 25 of the Lexmark Optra E312 user manual — 12 Chapter 1: The basics
Page 25 · click to enlarge
Page 25
ProblemWhat to do:

Toner smudges appear on the front or back of the page.

  • Make sure the paper is straight and unwrinkled.

Paper sticks together/printer feeds multiple sheets of paper.

  • Remove the paper from the paper feeder and fan the paper.
  • Make sure there isn’t too much paper in the paper feeder. The automatic paper feeder holds up to 150 sheets, depending on the thickness of the paper.

Paper fails to feed from the automatic paper feeder.

  • Remove the paper from the paper feeder and fan the paper.
  • Paper skews or buckles.
  • Make sure there isn’t too much paper in the paper feeder. The automatic paper feeder holds up to 150 sheets, depending on the thickness of the paper.
  • Make sure the paper guides are properly positioned against the edges of the paper.

Printing a test

To check that your printer is working correctly, print a test page.

page

To print a test page, the print cartridge must be installed (see Installing the print cartridge).

12 Chapter 1: The basics

Troubleshooting Tips

Page 26 of the Lexmark Optra E312 user manual — 13 Attaching a new operator panel overlay
Page 26 · click to enlarge
Page 26

1 Turn the printer off.

Lexmark Optra E312 — Attaching a new operator panel overlay diagram (page 26)
Fig. 18 · Attaching a new operator panel overlay

2 Plug one end of the power cord into the power cord connector on the back of the printer and the other end into a properly grounded wall outlet.

3 Turn on the printer.

As the printer powers up, each operator panel light turns on and off, starting with Press Button and ending with the Ready light. If this does not happen, see Printing problems.

4 When the Data light stops blinking and Ready is the only light on, briefly press the operator panel button.

A test page listing your printer model and default settings should print out. If it doesn’t, check Printing problems.

Lexmark Optra E312 — Attaching a new operator panel overlay diagram (page 26)
Fig. 19 · Attaching a new operator panel overlay

The operator panel lights do not come on when the printer is turned on.

  • Make sure the power cord is firmly plugged in at the back of the printer and at the wall outlet.

Attaching a new

If you have a non-English overlay sheet in your printer box and wish to use it, peel it off and place it over the overlay currently on your printer.

operator panel

overlay

13 Attaching a new operator panel overlay

Troubleshooting Tips

Page 27 of the Lexmark Optra E312 user manual — 14 Chapter 1: The basics
Page 27 · click to enlarge
Page 27

Installing memory To install a memory card or a flash memory card, go on to the next section. Otherwise, you are ready to set up your application software and install the appropriate printer driver. Refer to the booklet that came with the Drivers, MarkVision and Utilities CD for installation instructions. Go to Printer drivers for more information about the printer utilities and drivers.

Your printer comes with 4MB of printer memory. You can buy and install a 4MB, 8MB, 16MB, 32MB or 64MB optional memory card for a total of 68MB of printer memory.

You can also install a 1MB, 2MB or 4MB optional flash memory card for storing downloaded fonts or macros.

Removing the system board shield

Before installing any of these option cards, you will need a small Phillips screwdriver to remove the metal shield covering the printer system board.

1 Turn off the printer and unplug the power cord from the printer.

2 Disconnect the printer cable (if attached) from the printer.

3 Remove the print cartridge and cover it.

14 Chapter 1: The basics

Page 28 of the Lexmark Optra E312 user manual — 15 Installing memory
Page 28 · click to enlarge
Page 28

4 With the printer facing you, place it on its left side.

5 Turn the printer around so the bottom of the printer is facing you.

6 Locate and remove the 3 screws on the metal shield.

15 Installing memory

Page 29 of the Lexmark Optra E312 user manual — 16 Chapter 1: The basics
Page 29 · click to enlarge
Page 29

7 Grasp the corner of the shield and gently pull it out, then down.

Lexmark Optra E312 — Installing memory diagram (page 29)
Fig. 20 · Installing memory
Lexmark Optra E312 — Installing memory diagram (page 29)
Fig. 21 · Installing memory
Lexmark Optra E312 — Installing memory diagram (page 29)
Fig. 22 · Installing memory

8 Pull the shield away from the printer.

16 Chapter 1: The basics

Page 30 of the Lexmark Optra E312 user manual — 17 Installing memory
Page 30 · click to enlarge
Page 30

Installing a printer

To install an optional printer memory card, follow the instructions below.

memory card

1 Remove the printer memory card from its packaging.

Avoid touching the connection points along the edge of the card.

2 Locate the printer memory connector.

Lexmark Optra E312 — memory card diagram (page 30)
Fig. 23 · memory card

3 Hold the option card with the connection points facing toward the system board, with the notch pointing down and to the left.

4 Insert the card into the printer memory connector at a 45 degree angle.

17 Installing memory

Notch · Connection points

Page 31 of the Lexmark Optra E312 user manual — memory card
Page 31 · click to enlarge
Page 31

5 Gently push the card all the way in.

Lexmark Optra E312 — Installing memory diagram (page 31)
Fig. 24 · Installing memory

6 Push the card back with your thumbs until it snaps into place.

Installing a flash

To install an optional flash memory card:

memory card

1 Remove the printer memory card from its packaging.

Avoid touching the connection points along the edge of the card.

2 Locate the option card connector.

Lexmark Optra E312 — memory card diagram (page 31)
Fig. 25 · memory card

Notch · Connection points

Page 32 of the Lexmark Optra E312 user manual — 19 Installing memory
Page 32 · click to enlarge
Page 32

3 Hold the option card with the connection points facing toward the system board and the notch pointing down and to the left.

4 Insert the card into the option card connector at a 45 degree angle.

5 Gently push the card all the way in.

6 Push the card back with your thumbs until it snaps into place.

19 Installing memory

Page 33 of the Lexmark Optra E312 user manual — 20 Chapter 1: The basics
Page 33 · click to enlarge
Page 33

When you have finished installing the option card(s):

1 Fit the metal shield into the slots and reattach the screws.

2 Put the printer back to its original upright position.

3 Re-install the print cartridge.

4 Reconnect the computer cable and latch the metal clips.

5 Plug the power cord into the printer.

6 Turn the printer on.

As the printer powers up and the operator panel lights begin cycling on and off, there is a pause while the new memory is tested, then the lights continue cycling.

7 When the Ready light comes on, press the operator panel button briefly and print a test page to verify that printer memory or additional flash memory is installed.

If the Ready light does not come on, see Printing problems.

20 Chapter 1: The basics

Page 34 of the Lexmark Optra E312 user manual — 21 Printer drivers
Page 34 · click to enlarge
Page 34

Printer drivers

Lexmark Optra E312 — Printer drivers diagram (page 34)
Fig. 26 · Printer drivers

Included with your printer is the Drivers, MarkVision and Utilities CD, a compact disc containing printer drivers and utilities for Windows 95, Windows 98, Windows 2000, Windows NT 4.0, Windows 3.1x, Macintosh and OS/2 operating systems. Refer to the CD booklet for information about launching the CD program for your operating system. When the CD program is running, press F1 for online Help at any time.

You can also create diskettes from the CD or visit our web site at http://www.lexmark.com to download a printer driver to your computer.

Printer drivers Printer drivers for the following operating systems and applications are included on the CD:

  • Windows 95
  • Windows 98
  • Windows 2000
  • Windows NT 4.0
  • Windows for Workgroups 3.11
  • Windows 3.1x
  • Macintosh OS8 or later
  • OS/2 Warp
  • OS/2, 2.1 or later
  • WIN-OS/2 for OS/2, 2.1 or later

21 Printer drivers

Page 35 of the Lexmark Optra E312 user manual — 22 Chapter 2: Printer drivers
Page 35 · click to enlarge
Page 35

Additional printer drivers may have been developed since this book was printed. Refer to the CD README for a complete list of all the drivers included on the CD.

Automated fax

In the U.S. and Canada, you can get a list of available drivers by calling the Lexmark Automated Fax System. The system is available 24 hours a day, 7 days a week. Just call (606) 232-2380 from a touchtone phone and follow the voice prompts.

system

If you have a modem attached to your computer, you can download printer drivers from the Lexmark web site (www.lexmark.com).

Printer utilities The CD also includes printer utilities. If you’re using Windows 95, Windows 98, Windows 2000, Windows NT 4.0, Macintosh or OS/2 Warp, you can install the MarkVision utility.

22 Chapter 2: Printer drivers

Page 36 of the Lexmark Optra E312 user manual — 23 MarkVision
Page 36 · click to enlarge
Page 36

MarkVision With its easy-to-use tabs, MarkVision provides a quick and easy way to view and change printer settings right from your computer. You can:

  • select the status tab to view up-to-the-minute printer status
  • use Quick Setup to save your printer settings and set up one or more printers with your printer configuration
  • download fonts and overlays with the Windows Toolkit
  • use Printer Job Management to view and manage printer jobs

To install MarkVision, refer to the MarkVision online documentation on the Drivers, MarkVision and Utilities CD that came with your printer.

Online help Online Help is available from all MarkVision screens. MarkVision for Windows 95, Windows 98, Windows 2000 and Windows NT 4.0 includes step-by-step instructions for using many MarkVision functions.

23 MarkVision

Page 37 of the Lexmark Optra E312 user manual — 24 Chapter 2: Printer drivers
Page 37 · click to enlarge
Page 37

24 Chapter 2: Printer drivers

Page 38 of the Lexmark Optra E312 user manual — 25 Paper handling
Page 38 · click to enlarge
Page 38

Paper handling

Lexmark Optra E312 — Paper handling diagram (page 38)
Fig. 27 · Paper handling

Your printer has two standard paper sources: an automatic paper feeder, which holds up to 150 sheets of plain paper and a single sheet manual feeder. Use the automatic paper feeder for the print jobs you do most often. Use the manual sheet feeder to feed a single page, transparency, envelope, label or index card.

Lexmark Optra E312 — Paper handling diagram (page 38)
Fig. 28 · Paper handling

Your printer also has an output bin on top of the printer that collates up to 100 sheets (face down), and the single sheet front output door, which lets you feed media straight out the front of the printer, reducing curling and potential paper jams when using special media such as transparencies, envelopes, labels, card stock or index cards.

25 Paper handling

Manual sheet feeder

Page 39 of the Lexmark Optra E312 user manual — 26 Chapter 3: Paper handling
Page 39 · click to enlarge
Page 39

Paper types and

Selecting the right paper type reduces printing problems. For best print quality, use 20 lb (75 g/m2) xerographic paper.

sizes

If the paper has a preferred print side, load it with the print side facing you.

Lexmark Optra E312 — sizes diagram (page 39)
Fig. 29 · sizes
Transparencies Minimum3.875 x 5.9 in. (98 mm x 152 mm)
Maximum8.5 x 14 in. (216 mm x 356 mm)
Envelopes Minimum3.875 x 5.9 in. (98 mm x 152 mm)
Maximum8.5 x 14 in. (216 mm x 356 mm)
Labels Minimum3.875 x 5.9 in. (98 mm x 152 mm)
Maximum8.5 x 14 in. (216 mm x 356 mm)
Index Cards Minimum3 x 5 in. (76.2 x 127.0 mm)
Minimum3 x 5 in. (76.2 x 127.0 mm)
67. 90 lb Index Bristol (120 - 163 g/m 2 )
50. 100 lb tag (75 - 163 g/m 2 )
Maximum8.5 x 14 in. (216 mm x 356 mm)

26 Chapter 3: Paper handling

Page 40 of the Lexmark Optra E312 user manual — 27 Paper types and sizes
Page 40 · click to enlarge
Page 40

Paper Load A4, A5, B5, letterhead, legal and executive-size paper one at a time from the manual feeder or load up to 150 sheets in the automatic paper feeder.

Preprinted papers such as letterhead must be able to withstand temperatures up to 200°C (392°F) without melting or releasing hazardous emissions.

Load letterhead with the top of the page pointing down, facing you.

Transparencies If you occasionally print transparencies:

  • Use transparencies designed for laser printers. We recommend Lexmark Laser Printer Transparencies: for letter size transparencies, part number 70X7240; for A4 size transparencies, part number 12A5010. Transparencies must be able to withstand temperatures of 200°C (392°F) without melting or releasing hazardous emissions.
  • Test the print quality before buying large quantities.
  • Load transparencies with a removable stripe so the stripe is away from you and pointing down.

Envelopes For occasional envelope printing, feed envelopes one at a time from the manual feeder, or load up to 10 envelopes in the automatic paper feeder.

27 Paper types and sizes

Page 41 of the Lexmark Optra E312 user manual — 28 Chapter 3: Paper handling
Page 41 · click to enlarge
Page 41
Lexmark Optra E312 — Paper types and sizes diagram (page 41)
Fig. 30 · Paper types and sizes

Load envelopes in the center of the manual feeder or automatic paper feeder and slide the paper guides snugly against the sides of the envelopes.

When printing on envelopes:

  • Try a sample of any envelopes you are considering using with the printer before buying large quantities.
  • Use envelopes made from 75 to 105 g/m 2 (20 to 28 lb) bond paper. For best performance and fewer paper jams, do not use envelopes that:

– have excessive curl – are stuck together – are damaged in any way – contain windows, holes, perforations, cutouts or embossing – use metal clasps, string ties or metal folding bars – have postage stamps attached – have any exposed adhesive when the flap is in the sealed position

  • Use envelopes that can withstand temperatures of 200°C (392°F) without sealing, excessive curling, wrinkling or releasing hazardous emissions.

28 Chapter 3: Paper handling

Page 42 of the Lexmark Optra E312 user manual — 29 Paper types and sizes
Page 42 · click to enlarge
Page 42
  • Load envelopes vertically, flap side down so the stamp area is in the top left corner.
  • Adjust the left and right paper guides to fit the width of the envelopes.

Labels For occasional label printing, use paper labels designed for laser printers. You can feed labels one at a time from the manual feeder, or you can load up to 10 labels in the automatic paper feeder.

When printing on labels:

  • Test the print quality before buying large quantities of labels.
  • Use labels with a pressure of 25 psi that can withstand temperatures of 200°C (392°F) without releasing hazardous emissions. For more information on label printing, refer to the Card Stock & Label Guide on the CD.
  • Do not print a large number of labels continuously.
  • Do not use labels that have exposed adhesive on the sheets.

Card stock For occasional printing on index Bristol or tag card stock, feed 1 card at a time in the manual paper feeder. Use card stock with a maximum weight of 163 g/m2 and a minimum size of 76.2 x 127 mm (3 x 5 in.).

29 Paper types and sizes

Page 43 of the Lexmark Optra E312 user manual — 30 Chapter 3: Paper handling
Page 43 · click to enlarge
Page 43

For best results, open the single-sheet front output door so the card stock exits out the front.

Loading paper, other media in the

Use the automatic paper feeder, which is behind the manual feeder, to feed paper and special media such as transparencies, envelopes, labels and card stock.

automatic feeder

To avoid curling and potential jams when printing on special media, open the front output door to feed the media straight out the front of the printer.

1 Extend the paper support on the automatic paper feeder.

2 Before loading media, flex the sheets back and forth to loosen them, then fan them.

The automatic paper feeder holds up to 150 sheets of paper, 10 sheets of transparencies or labels, 10 envelopes, 10 index cards.

30 Chapter 3: Paper handling

Page 44 of the Lexmark Optra E312 user manual — 31 Loading paper, other media in the automatic feeder
Page 44 · click to enlarge
Page 44

3 If loading:

  • A4, A5, B5, legal or executive-size paper, insert the paper with the print side facing you
  • letterhead paper, insert letterhead with the top of the page pointing down, facing you
  • transparencies with a removable stripe, insert them so the stripe is pointing away from you and pointing down
  • envelopes, insert them vertically, flap side down so the stamp area is in the top left corner

4 Slide the paper guides flush against the edges of the media.

31 Loading paper, other media in the automatic feeder

Page 45 of the Lexmark Optra E312 user manual — 32 Chapter 3: Paper handling
Page 45 · click to enlarge
Page 45

5 Extend the paper support on the paper output bin or open the front output door if you’re printing on special media.

Lexmark Optra E312 — Loading paper, other media in the automatic feeder diagram (page 45)
Fig. 31 · Loading paper, other media in the automatic feeder

6 Select the automatic paper feeder from your software application.

Lexmark Optra E312 — Loading paper, other media in the automatic feeder diagram (page 45)
Fig. 32 · Loading paper, other media in the automatic feeder

7 Start your print job.

32 Chapter 3: Paper handling

Page 46 of the Lexmark Optra E312 user manual — 33 Loading paper, other media in the manual sheet feeder
Page 46 · click to enlarge
Page 46

Loading paper, other media in the

Use the manual feeder to feed paper or special media, one sheet at a time, into your printer.

manual sheet

If you experience problems feeding envelopes or index cards in the automatic paper feeder, try printing them one at a time from the manual feeder.

feeder

To avoid curling or potential jams when printing on special media, open the front output door to feed media straight out the front of the printer.

1 Extend the paper support on the paper output bin or open the front output door if you’re printing on special media.

2 If loading:

Lexmark Optra E312 — 2 If loading: diagram (page 46)
Fig. 33 · 2 If loading:
  • paper, insert one sheet of paper with the print side facing you
  • letterhead paper, insert one sheet of letterhead with the top of the page pointing down, facing you
  • transparencies with a removable stripe, insert one transparency so the stripe is pointing away from you and pointing down
  • envelopes, insert one envelope vertically, flap side down so the stamp area is in the top left corner
  • card stock, insert one card vertically

3 Slide the paper guides flush against the edges of the media.

Lexmark Optra E312 — 2 If loading: diagram (page 46)
Fig. 34 · 2 If loading:

4 Briefly (approximately one second) push Press Button to start printing.

5 When the Load Paper light blinks and the Press Button light comes on, place another sheet/other media in the manual feeder. If you are using MarkVision, you will get a load manual paper/ envelope message.

33 Loading paper, other media in the manual sheet feeder

Page 47 of the Lexmark Optra E312 user manual — 34 Chapter 3: Paper handling
Page 47 · click to enlarge
Page 47

Clearing paper

If you get a paper jam, the Paper Jam indicator light prompts you to clear the paper path.

jams

If the paper has just started to feed from the paper feeder when the jam occurs:

1 Pull the paper straight up out of the paper feeder.

2 Open and close the printer cover to resume printing.

If the paper jam occurs inside the printer:

1 Remove the paper from the output bin.

2 Turn the printer off, then on.

If this doesn’t clear the jam:

3 Open the printer cover.

4 Remove the print cartridge and cover it.

34 Chapter 3: Paper handling

Page 48 of the Lexmark Optra E312 user manual — 35 Clearing paper jams
Page 48 · click to enlarge
Page 48

5 Grasp the paper on both sides and pull the paper toward you.

Lexmark Optra E312 — Clearing paper jams diagram (page 48)
Fig. 35 · Clearing paper jams

6 Make sure there is no more paper in the printer.

7 Re-insert the print cartridge.

8 Close the printer cover to resume printing.

If a paper jam occurs while printing labels:

1 Be sure the labels remain attached to the backing sheet after clearing the paper jam.

2 Feed 10 or more sheets of plain paper through the printer before resuming label printing. The plain paper will remove any remaining adhesive in or on the fusing unit.

35 Clearing paper jams

Page 49 of the Lexmark Optra E312 user manual — 36 Chapter 3: Paper handling
Page 49 · click to enlarge
Page 49
Lexmark Optra E312 — Clearing paper jams diagram (page 49)
Fig. 36 · Clearing paper jams
  • Make sure you are using recommended paper/other media (see Paper types and sizes ).
  • Envelopes fail to feed correctly.
  • Make sure the envelopes are loaded in the center of the feeder.
  • Try a different kind. Envelopes designed for laser printers produce better results.

36 Chapter 3: Paper handling

Troubleshooting Tips

Page 50 of the Lexmark Optra E312 user manual — 37 Troubleshooting
Page 50 · click to enlarge
Page 50

Troubleshooting

Lexmark Optra E312 — Troubleshooting diagram (page 50)
Fig. 37 · Troubleshooting

For help solving printing problems, refer to the following tables. If you cannot fix the problem, contact your point of purchase for assistance. You may have a printer part that requires cleaning or replacement by a service technician.

ProblemWhat to do:
  • Light or blurred characters.
  • Make sure you removed the sealing tape from the print cartridge.
  • Hot/humid or cold/dry weather conditions may affect how well toner adheres to paper. Select the next darker print setting.
  • If Toner Saver is on, turn it off using MarkVision or your printer driver.
  • Remove the print cartridge, shake it from side-to-side to redistribute the toner, and reinsert it.
  • Run Engine Clean Cycle to remove any toner that may have accumulated (see Engine clean cycle ).
  • Make sure you are using recommended paper/other media (see Paper types and sizes ).
  • Use MarkVision to define the Custom Type setting for media type, media texture or media weight.
  • Replace the print cartridge.

Toner smudges appear on the front or back of the page.

  • Run Engine Clean Cycle to remove any toner that may have accumulated ( Engine clean cycle ).
  • Make sure the paper is straight and unwrinkled.
  • Replace the print cartridge.

Vertical or horizontal streaks appear on the page.

  • Run Engine Clean Cycle to remove any toner that may have accumulated ( Engine clean cycle ).
  • Replace the print cartridge.

37 Troubleshooting

Print quality problems

Page 51 of the Lexmark Optra E312 user manual — 38 Chapter 4: Troubleshooting
Page 51 · click to enlarge
Page 51
  • Toner smears or rubs off the page.
  • Run Engine Clean Cycle to remove any toner that may have accumulated ( Engine clean cycle ).
  • Select a different Media Type or Form Type setting from your Lexmark printer driver.
  • Try a different kind of xerographic bond paper.

Solid black areas on transparencies or paper contains white streaks.

  • Choose a different fill pattern in your software application.
  • Try a different type of paper. Paper designed for copiers give the best quality.
  • Replace the print cartridge.

Faint images or repetitive spots appear on the page.

  • Select a different Media Type or Form Type setting from your Lexmark printer driver.
  • Try a different kind of xerographic bond paper.
  • Replace the print cartridge.
ProblemWhat to do:

Printer has missing or damaged parts.

  • Inside the U.S., call the number listed on your printer registration card.
  • Outside the U.S., contact your point of purchase.

Power is turned on at a power strip but the Ready light is not on.

  • Be sure the printer power switch is on too.
  • Printer is on, but nothing prints.
  • Make sure the print cartridge is installed.
  • Make sure the parallel cable is firmly plugged into the connector on the back of the printer.
  • Print a test page (do a brief button press) to determine if the problem is with the printer or the computer. — If you can print a test page, the problem is in the computer or the

software application. — If you cannot print a test page, call the Lexmark service number listed

on the printer registration card.

Printer does not print even though a paper jam has been cleared.

  • Open and close the printer cover to restart the printer.

Unexpected characters print or characters are missing.

  • Make sure you are using the correct printer driver.
  • Select Hex Trace Mode from the Special Function Menu to determine what the problem is.
  • Restore factory defaults ( Reset user defaults ).

While in PostScript Level 2 emulation, the printer is flushing data (Data and Error indicator lights are blinking).

  • Make sure you are using the correct PostScript driver.
  • The printer doesn’t have enough memory to print the job. Install more memory (see Installing a printer memory card ).

While in MarkVision, the Press Button light is on.

  • The printer is off-line. Press and hold the operator panel button for 3 seconds to reset the printer.

38 Chapter 4: Troubleshooting

Print quality problems · Printing problems

Page 52 of the Lexmark Optra E312 user manual — 39 Indicator lights
Page 52 · click to enlarge
Page 52

Indicator lights

The next section explains the various light sequences with a corresponding illustration.

Lexmark Optra E312 — Indicator lights diagram (page 52)
Fig. 38 · Indicator lights

The indicator lights mean different things, depending on their sequence. They indicate that the printer is Ready to print (printer status information); the printer needs attention (printer attendance information); or the printer needs servicing (printer service information).

Lexmark Optra E312 — Indicator lights diagram (page 52)
Fig. 39 · Indicator lights
  • Brief button press (push the button once for no more than 3 seconds)
  • Long button press (hold until all the lights come on)
  • Double click button press (push and release the button twice quickly)

39 Indicator lights

Operator panel terms

Page 53 of the Lexmark Optra E312 user manual — 40 Chapter 4: Troubleshooting
Page 53 · click to enlarge
Page 53

Printer status

information

If your printer lights look like this: Then your printer:

is Ready to receive and process data.

  • Print a test page by pushing the operator panel button with a brief button press, or
  • reset the printer by pushing the operator panel button with a long button press. Each time the printer is reset, the print job in process is terminated.

40 Chapter 4: Troubleshooting

Page 54 of the Lexmark Optra E312 user manual — 41 Indicator lights
Page 54 · click to enlarge
Page 54
Lexmark Optra E312 — Indicator lights diagram (page 54)
Fig. 40 · Indicator lights

If your printer lights look like this: Then your printer:

is Busy receiving data, processing data, the print engine is running, or processing/printing a test page.

  • If you want to reset the printer, push the operator panel button with a long button press.

41 Indicator lights

Page 55 of the Lexmark Optra E312 user manual — 42 Chapter 4: Troubleshooting
Page 55 · click to enlarge
Page 55
Lexmark Optra E312 — Indicator lights diagram (page 55)
Fig. 41 · Indicator lights

If your printer lights look like this: Then your printer:

is Waiting until a Print Timeout occurs or until additional data is received.

  • Print data stored in the printer buffer by pushing the operator panel button with a brief button press or
  • reset the printer by pushing the operator panel button with a long button press.

42 Chapter 4: Troubleshooting

Page 56 of the Lexmark Optra E312 user manual — 43 Indicator lights
Page 56 · click to enlarge
Page 56

If your printer lights look like this: Then your printer:

is Resetting settings to their power-on default settings or saving settings changed in configuration mode.

43 Indicator lights

Page 57 of the Lexmark Optra E312 user manual — 44 Chapter 4: Troubleshooting
Page 57 · click to enlarge
Page 57

If your printer lights look like this: Then your printer:

is Flushing corrupted print data.

44 Chapter 4: Troubleshooting

Page 58 of the Lexmark Optra E312 user manual — 45 Indicator lights
Page 58 · click to enlarge
Page 58

Printer attendance

information

Lexmark Optra E312 — Printer attendance diagram (page 58)
Fig. 42 · Printer attendance

If your printer lights look like this: Then your printer:

  • Open the printer cover, clear all paper from the paper path and close the cover to resume printing.

45 Indicator lights

Page 59 of the Lexmark Optra E312 user manual — 46 Chapter 4: Troubleshooting
Page 59 · click to enlarge
Page 59
Lexmark Optra E312 — Indicator lights diagram (page 59)
Fig. 43 · Indicator lights

If your printer lights look like this: Then your printer:

is prompting you to load media for manual feed. The printer stops and displays this light sequence for each piece of media you want to print.

  • Load media, with the side to be printed facing the front of the printer, into the manual feeder and push the operator panel button to resume printing, or
  • reset the printer by pushing the operator panel button with a long button press.
Lexmark Optra E312 — Indicator lights diagram (page 59)
Fig. 44 · Indicator lights

If your printer lights look like this: Then your printer:

is alerting you that the printer is out of paper/envelopes or that the paper did not feed properly from the automatic paper feeder.

  • Load media into the automatic paper feeder and push the operator panel button to resume printing or
  • reset the printer by pushing the operator panel button with a long button press.

46 Chapter 4: Troubleshooting

Page 60 of the Lexmark Optra E312 user manual — 47 Indicator lights
Page 60 · click to enlarge
Page 60

If your printer lights look like this: Then your printer:

top cover is open or the print cartridge is not installed.

  • Close the cover to display the light sequence that appeared before the cover was opened.
  • Install the print cartridge.

47 Indicator lights

Page 61 of the Lexmark Optra E312 user manual — 48 Chapter 4: Troubleshooting
Page 61 · click to enlarge
Page 61

If your printer lights look like this: Then your printer:

  • memory is full , or
  • received a page that is too complex to print, or
  • reduces the resolution of a formatted page to 300 dpi before printing, or
  • has a PPDS font error , or
  • doesn’t have enough memory to save what is in the buffer ( resource save off ), or
  • doesn’t have enough memory to defragment flash memory ( insufficient defrag memory ), or
  • cannot communicate with the host computer ( host interface error ).

Each of the errors described above has a unique, secondary error code. Display the secondary error code by double-clicking the operator panel button.

48 Chapter 4: Troubleshooting

Page 62 of the Lexmark Optra E312 user manual — 49 Indicator lights
Page 62 · click to enlarge
Page 62

Secondary error

codes

Lexmark Optra E312 — Secondary error diagram (page 62)
Fig. 45 · Secondary error

If your printer lights look like this when you double-click the operator panel button:

  • Reduce the complexity of the job and/or the resolution, or
  • press the operator panel button with a brief button press to resume printing, or
  • reset the printer by pushing the operator panel button with a long button press.

49 Indicator lights

Page 63 of the Lexmark Optra E312 user manual — 50 Chapter 4: Troubleshooting
Page 63 · click to enlarge
Page 63

If your printer lights look like this when you double-click the operator panel button:

Then your printer:

has received a page that is too complex to print (Complex Page).

  • Switch the printing mode to a different printing mode via the Lexmark driver for Windows, or
  • press the operator panel button with a brief button press to resume printing, or
  • reset the printer by pushing the operator panel button with a long button press.

50 Chapter 4: Troubleshooting

Page 64 of the Lexmark Optra E312 user manual — 51 Indicator lights
Page 64 · click to enlarge
Page 64

If your printer lights look like this when you double-click the operator panel button:

Then your printer:

is out of memory while formatting a page and is forced to reduce the

51 Indicator lights

Page 65 of the Lexmark Optra E312 user manual — 52 Chapter 4: Troubleshooting
Page 65 · click to enlarge
Page 65

If your printer lights look like this when you double-click the operator panel button:

Then your printer:

has received a request for a PPDS font which is not installed (Font Error).

  • Reset the front panel by pushing the operator panel button with a long button press.

52 Chapter 4: Troubleshooting

Page 66 of the Lexmark Optra E312 user manual — 53 Indicator lights
Page 66 · click to enlarge
Page 66
Lexmark Optra E312 — Indicator lights diagram (page 66)
Fig. 46 · Indicator lights

If your printer lights look like this when you double-click the operator panel button:

doesn’t have enough memory to save what is in the buffer (Resource Save Off).

  • push the operator panel button to resume printing, or
  • reset the front panel by pushing the operator panel button with a long button press.

53 Indicator lights

Page 67 of the Lexmark Optra E312 user manual — 54 Chapter 4: Troubleshooting
Page 67 · click to enlarge
Page 67
Lexmark Optra E312 — Indicator lights diagram (page 67)
Fig. 47 · Indicator lights

If your printer lights look like this when you double-click the operator panel button:

has insufficient memory to free up unused space in flash memory (Insufficient Defrag Memory).

  • Delete fonts, macros and other data in RAM, or install additional printer memory, then issue a PJL command to begin freeing up unused space in flash memory.

54 Chapter 4: Troubleshooting

Page 68 of the Lexmark Optra E312 user manual — 55 Indicator lights
Page 68 · click to enlarge
Page 68

If your printer lights look like this when you double-click the operator panel button:

Then your printer:

has an error communicating with the host computer (Host Interface Error).

This error is displayed if:

  • you have an external print server connected to your printer, but your printer can’t detect it when you first turn the printer on, or
  • the computer attempts to communicate with the printer through the parallel port, but the port setting has been disabled in configuration mode, or
  • the computer attempts to communicate with the printer through the USB port, but the port has been disabled in configuration mode.
  • If this error occurs when you turn on the printer, double check that the ENA is still plugged in to the printer.
  • If you want to print through the parallel port, print a menu settings page (see Printing a test page ) to verify that the parallel buffer setting is disabled. Re-enable the parallel port in configuration mode (see the table on page 69 ).
  • If you’re printing through the USB port, print a menu settings page (see Printing a test page ) to verify that the USB buffer setting is disabled. Re-enable the USB port in configuration mode (see the table on page 76 ).

55 Indicator lights

Page 69 of the Lexmark Optra E312 user manual — 56 Chapter 4: Troubleshooting
Page 69 · click to enlarge
Page 69

Printer service

information

Lexmark Optra E312 — Printer service diagram (page 69)
Fig. 48 · Printer service

If your printer lights look like this: Then your printer:

  • Turn the printer off and back on. If the lights are still blinking, contact your point of purchase, or call the Lexmark service number listed on your printer registration card.

Reset user defaults When formatting problems occur or unexpected characters print, try resetting the printer default settings to your user defaults. Press and hold the operator panel button until all indicator lights are on.

Lexmark Optra E312 — Printer service diagram (page 69)
Fig. 49 · Printer service

Once the default settings are reset, the Ready light comes on.

56 Chapter 4: Troubleshooting

Page 70 of the Lexmark Optra E312 user manual — 57 Indicator lights
Page 70 · click to enlarge
Page 70

Engine clean cycle For print quality problems, such as stray toner marks appearing on the paper, select the Engine Clean Cycle setting to remove any toner that may have accumulated.

1 Turn off the printer.

2 Open the top cover.

3 Turn the printer back on.

4 Load paper into the paper feeder.

5 When the Error light comes on, indicating the top cover is open, do a double button press.

6 When the Error light and Press Button light blink, close the cover.

The Special Function Menu is activated.

Engine Clean Cycle is the first menu selection in the Special Function Menu. The operator panel Ready light is on solid, the Error light is blinking and the Press Button light is blinking.

7 Do a long button press to start Engine Clean Cycle.

a The printer feeds one sheet of plain paper

through the paper path to remove any accumulated toner.

b Once the paper exits into the output bin, the

printer returns to the Ready state.

8 If necessary, repeat this process two or three times until all of the excess toner is removed.

57 Indicator lights

Page 71 of the Lexmark Optra E312 user manual — 58 Chapter 4: Troubleshooting
Page 71 · click to enlarge
Page 71

Print quality test

To help isolate print quality problems, like streaking, select the Print Quality Test Pages setting.

pages

1 Turn off the printer.

2 Open the top cover.

3 Turn the printer back on.

4 Load paper into the paper feeder.

5 When the Error light comes on, indicating the top cover is open, do a double button press.

6 When the Error light and Press Button light blink, close the cover.

Do a double button press 4 times to scroll down to Print Quality Test Pages.

Lexmark Optra E312 — pages diagram (page 71)
Fig. 50 · pages

The operator panel Ready light is on solid, the Data light is on solid, the Error light is blinking and the Press Button light is blinking.

7 Do a long button press to start Print Quality Test Pages.

a Three pages print out to help you evaluate

print quality. The first page has registration marks, the second page is gray and the third page is black.

b Once the paper exits into the output bin, the

printer returns to the Ready state.

When you’ve isolated the problem, i.e., print is too light, toner streaks, and so on, refer to the troubleshooting tables beginning on page 37.

58 Chapter 4: Troubleshooting

Page 72 of the Lexmark Optra E312 user manual — 59 Indicator lights
Page 72 · click to enlarge
Page 72

Enter Hex Trace

When unexpected characters print or characters are missing, use Hex Trace to help you determine if there is a problem with the language interpreter or the cable. Hex Trace isolates printing problems by telling you what information your printer is receiving.

mode

To enter Hex Trace mode:

1 Turn off the printer.

2 Open the top cover.

3 Turn the printer back on.

4 When the Error light comes on, indicating the top cover is open, do a double button press.

Lexmark Optra E312 — mode diagram (page 72)
Fig. 51 · mode

5 When the Error light and Press Button light blink, close the cover.

6 Do a double button press 3 times to scroll down to Enter Hex Trace.

When the Enter Hex Trace setting is selected, the Paper Jam light is on solid, the Error light is blinking and the Press Button light is blinking.

7 Do a long button press to start Hex Trace.

Data sent to the printer is printed out in hexadecimal and character representation to help isolate the source of the problem.

8 To exit Hex Trace, turn off the printer or press the operator panel button to reset the printer.

59 Indicator lights

Page 73 of the Lexmark Optra E312 user manual — 60 Chapter 4: Troubleshooting
Page 73 · click to enlarge
Page 73

Restore factory

If changing the printer user default settings does not solve formatting problems, reset the printer to the original factory default settings.

defaults

1 Turn off the printer.

2 Open the top cover.

3 Turn the printer back on.

4 Load paper into the paper feeder.

5 When the Error light comes on, indicating the top cover is open, do a double button press.

Lexmark Optra E312 — defaults diagram (page 73)
Fig. 52 · defaults

6 When the Error light and Press Button light blink, close the cover.

7 Do a double button press 1 time to scroll down to Reset Defaults.

The operator panel Data light is on solid, the Error light is blinking and the Press Button light is blinking.

8 Do a long button press to reset the printer to the original factory defaults.

Once the settings are returned to the factory default values, the printer returns to the Ready state.

60 Chapter 4: Troubleshooting

Page 74 of the Lexmark Optra E312 user manual — 61 Indicator lights
Page 74 · click to enlarge
Page 74

Before you call for

If you can’t solve your printer problems, it’s time to call for service. Before you call, however, check the following:

service

  • Is the power cord plugged into the printer?
  • Is the power cord plugged directly into a properly grounded wall outlet?
  • Is your printer properly connected to your computer?
  • Are all other devices attached to your printer plugged in and turned on?
  • Is the wall outlet turned off by any switches?
  • Did a fuse blow?
  • Has a power outage occurred in your area?
  • Is a print cartridge installed in your printer?
  • Is the printer cover closed completely?

Once you’ve checked these things, turn your printer off and back on again. If your printer is still not operating properly, call the Lexmark service number listed on the printer registration card or contact your point of service.

If the Ready indicator light is on, briefly press the operator panel button to print a test page. It lists your printer model, printer memory installed and your user default settings. The service representative will probably ask for this information.

61 Indicator lights

Page 75 of the Lexmark Optra E312 user manual — 62 Chapter 4: Troubleshooting
Page 75 · click to enlarge
Page 75

62 Chapter 4: Troubleshooting

Page 76 of the Lexmark Optra E312 user manual — 63 Print cartridge maintenance
Page 76 · click to enlarge
Page 76

Supplies

Lexmark Optra E312 — Supplies diagram (page 76)
Fig. 53 · Supplies

Within the U.S. or Canada, you can order Lexmark supplies from any Lexmark Authorized Supplies Dealer. To locate the dealer nearest you, call the number on the printer registration card that came with your printer. In other countries, contact the place where you bought your printer.

Print cartridge

To get the maximum benefit from your print cartridge:

maintenance

  • Do not remove the print cartridge (P/N 13T0101) from its packaging until you are ready to install it.
  • Do not refill print cartridges. The printer warranty does not cover damage caused by using refilled cartridges .
  • Store print cartridges in the same environment as the printer.
  • Do not remove a print cartridge from the printer except to replace it or to clear a paper jam.

63 Print cartridge maintenance

Page 77 of the Lexmark Optra E312 user manual — 64 Chapter 5: Supplies
Page 77 · click to enlarge
Page 77
Lexmark Optra E312 — Supplies diagram (page 77)
Fig. 54 · Supplies
  • Characters appear light or blurred.
  • Make sure you removed the sealing tape from the print cartridge.
  • Replace the print cartridge.

Printer seems to be printing, but pages are blank.

  • The print cartridge may be out of toner. Replace the cartridge.
  • The print cartridge may be defective. Replace the cartridge.
  • Make sure you removed the sealing tape from the print cartridge.

Jobs are not printing and the Error light is on solid.

Recycling used

Lexmark’s Operation ReSourceSM program lets you participate in worldwide recycling at no cost to you.

supplies

Some shipping cartons have printed instructions for participating in Operation ReSource. Other supplies come packaged with a prepaid shipping label that you may use in the specified country. If the shipping label is not appropriate for your country, or if you need additional recycling instructions, contact the place where you bought your printer.

64 Chapter 5: Supplies

Troubleshooting Tips

Page 78 of the Lexmark Optra E312 user manual — 65 Appendix A: Printer specifications
Page 78 · click to enlarge
Page 78
Lexmark Optra E312 — Printer features diagram (page 78)
Fig. 55 · Printer features

Printer features • Prints up to 10 pages per minute

  • 600 and 300 dpi print resolutions
  • 1200 Image Quality
  • PostScript Level 2 emulation standard
  • PCL 6 and PCL 5e emulations standard
  • 45 LaserJet-compatible scalable fonts plus 30 additional PCL scalable fonts
  • 39 Optra-compatible scalable fonts plus 36 PostScript scalable fonts
  • 150-sheet automatic paper input tray and a single-sheet manual input tray
  • 100-sheet paper output tray and a single-sheet output door
  • 4MB printer memory
  • 4MB, 8MB, 16MB, 32MB and 64MB memory options for 68MB maximum memory expansion
  • 1MB, 2MB and 4MB flash memory options
  • USB capability
  • Single element print cartridge for easy, cleanhands installation

65 Appendix A: Printer specifications

Page 79 of the Lexmark Optra E312 user manual — 66 Appendix A: Printer specifications
Page 79 · click to enlarge
Page 79

Printer dimensions

Height8.8 in. (224 mm)
Width13.6 in. (345 mm)
Depth14.4 in. (365 mm)
Weight16.5 lb (7.5 kg) with print cartridge

66 Appendix A: Printer specifications

Page 80 of the Lexmark Optra E312 user manual — 67 Appendix B: Advanced troubleshooting
Page 80 · click to enlarge
Page 80
Lexmark Optra E312 — Printer dimensions diagram (page 80)
Fig. 56 · Printer dimensions

If you contact the Lexmark Customer Support Center to help you resolve a printing problem, they may guide you through configuration mode to change a default setting (i.e., turning on the PPDS Activated setting if your job application uses the PPDS datastream).

Use the operator panel or the MarkVision remote operator panel to set or change specific printer functions in configuration mode.

The following settings may be selected while in configuration mode:

  • Parallel Port Settings

– Enable Port – NPA Mode – Protocol – Mode 1 – Mode 2 – Strobe Adjust

  • USB Settings

– Enable Port – NPA Mode

  • PPDS Activated
  • Auto LFCR after CRLF

67 Appendix B: Advanced troubleshooting

Page 81 of the Lexmark Optra E312 user manual — 68 Appendix B: Advanced troubleshooting
Page 81 · click to enlarge
Page 81

To enter configuration mode you must be in the Special Function Menu:

1 Turn off the printer.

2 Open the top cover.

3 Turn the printer back on.

4 When the Error light comes on, indicating the top cover is open, do a double button press.

5 When the Error light and Press Button light blink, close the cover.

6 Do a double button press twice to scroll down to Enter Configuration Mode.

When the Enter Configuration Mode setting is selected, the operator panel Load Paper light is on solid, the Error light is blinking and the Press Button light is blinking.

7 Do a long button press to initiate Configuration Mode.

This illustration represents the operator panel settings in configuration mode when an indicator light is on solid.

When the printer is in configuration mode, the indicator lights take on new meanings based on their function. The following tables describe the function of each of these settings.

68 Appendix B: Advanced troubleshooting

Page 82 of the Lexmark Optra E312 user manual — 69 Appendix B: Advanced troubleshooting
Page 82 · click to enlarge
Page 82

If your printer lights look like this in configuration mode:

Then your printerFactory Default

Parallel Port Enabled setting is set to Auto, the factory default.

If your printer encounters a memory shortage when trying to print a job and you are not using the parallel port, turn off Parallel Port Enabled to free up a little more memory.

There are three settings for Parallel Port Enabled: Off, On and Auto.

  • Do a brief button press to scroll through the settings (Off, On, Auto) for this menu item.
  • Do a double button press to scroll to the next menu item, NPA Mode (Parallel).
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all operator panel indicator lights remain on for approximately 2 seconds.

Turn off the printer to exit configuration mode.

If your printer lights look like this in configuration mode:

Then your printerFactory Default

Parallel NPA Mode setting is set to Auto, the factory default.

When NPA Mode is enabled, your computer can send print jobs to the printer and query printer status information simultaneously.

There are three settings for NPA Mode (Parallel): Off, On and Auto.

  • Do a brief button press to scroll through the settings (Off, On, Auto) for this menu item.
  • Do a double button press to scroll to the next menu item, Parallel Protocol.
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all operator panel indicator lights remain on for approximately 2 seconds.

Turn off the printer to exit configuration mode.

69 Appendix B: Advanced troubleshooting

Auto · Auto

Page 83 of the Lexmark Optra E312 user manual — 70 Appendix B: Advanced troubleshooting
Page 83 · click to enlarge
Page 83

If your printer lights look like this in configuration mode:

Then your printerFactory Default

Parallel Protocol setting is set to Fastbytes, the factory default.

When the protocol is set to Fastbytes, the printer receives information at a much faster transmission rate, provided the host computer supports Fastbytes.

When the protocol is set to Standard, the printer receives information at a normal transmission rate. The Press Button light is off when Parallel Protocol is set to Standard.

  • Do a brief button press to change the setting (Fastbytes, Standard).
  • Do a double button press to scroll to the next menu item, PPDS Activated.
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all operator panel indicator lights remain on for approximately 2 seconds.

Turn off the printer to exit configuration mode.

70 Appendix B: Advanced troubleshooting

Fastbytes

Page 84 of the Lexmark Optra E312 user manual — 71 Appendix B: Advanced troubleshooting
Page 84 · click to enlarge
Page 84
Lexmark Optra E312 — Printer dimensions diagram (page 84)
Fig. 57 · Printer dimensions

If your printer lights look like this in configuration mode:

Turn PPDS Activated on when working in applications using the PPDS datastream.

There are two settings for PPDS Activated: On and Off.

  • Do a brief button press to change the setting (On, Off).
  • Do a double button press to scroll to the next menu item, Auto CRLF/LFCR.
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all operator panel indicator lights remain on for approximately 2 seconds.

71 Appendix B: Advanced troubleshooting

Page 85 of the Lexmark Optra E312 user manual — 72 Appendix B: Advanced troubleshooting
Page 85 · click to enlarge
Page 85

If your printer lights look like this in configuration mode:

Then your printerFactory Default

Auto CRLF/LFCR setting is off, the factory default.

How the printer formats the end of a line depends on the computer system being used. Use this setting to select whether or not the printer automatically performs a carriage return (CR) after a line feed (LF) or a line feed after a carriage return.

  • If the Press Button light is off, Auto CR after LF is Off and Auto LF after CR is Off.
  • If the Press Button light is on, Auto CR after LF is On and Auto LF after CR is Off.
  • If the Press Button light is blinking, Auto CR after LF is Off and Auto LF after CR is On.
  • Do a brief button press to scroll through the settings for this menu item.
  • Do a double button press to scroll to the next menu item, Parallel Mode 1.
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all operator panel indicator lights remain on for approximately 2 seconds.

Turn off the printer to exit configuration mode.

72 Appendix B: Advanced troubleshooting

Off

Page 86 of the Lexmark Optra E312 user manual — 73 Appendix B: Advanced troubleshooting
Page 86 · click to enlarge
Page 86

This illustration represents the operator panel settings in configuration mode when an indicator light is blinking. The following tables describe the function of each setting.

Lexmark Optra E312 — Printer dimensions diagram (page 86)
Fig. 58 · Printer dimensions

If your printer lights look like this in configuration mode:

Then your printerFactory Default

Parallel Mode 1 setting is on, the factory default.

This setting enables or disables the pull up resistors on the parallel port signals. It is useful for personal computers that have open collector outputs on the parallel port signals. Set Parallel Mode 1 On to disable the resistors or Off to enable the resistors.

  • Do a brief button press to scroll through the settings (On, Off) for this menu item.
  • Do a double button press to scroll to the next menu item, Parallel Mode 2.
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all operator panel indicator lights remain on for approximately 2 seconds.

Turn off the printer to exit configuration mode.

73 Appendix B: Advanced troubleshooting

On

Page 87 of the Lexmark Optra E312 user manual — 74 Appendix B: Advanced troubleshooting
Page 87 · click to enlarge
Page 87

If your printer lights look like this in configuration mode:

Then your printerFactory Default

Parallel Mode 2 setting is on, the factory default.

This setting determines if the parallel port data is sampled on the leading or trailing edge of strobe. If Parallel Mode 2 is set On, the parallel port data is sampled on the leading edge of strobe. The parallel port data is sampled on the trailing edge of strobe if Parallel Mode 2 is set Off.

  • Do a brief button press to scroll through the settings (On, Off) for this menu item.
  • Do a double button press to scroll to the next menu item, Parallel Strobe Adjust.
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all indicator lights remain on for approximately 2 seconds.

Turn off the printer to exit configuration mode.

74 Appendix B: Advanced troubleshooting

On

Page 88 of the Lexmark Optra E312 user manual — 75 Appendix B: Advanced troubleshooting
Page 88 · click to enlarge
Page 88
Lexmark Optra E312 — Printer dimensions diagram (page 88)
Fig. 59 · Printer dimensions

If your printer lights look like this in configuration mode:

Parallel Strobe Adjust setting is off (0), the factory default.

This setting lets you increase the amount of time strobe is sampled to determine that valid data is available on the parallel port.

  • Do a brief button press to scroll through the settings (Off=0, On=+1, Auto=+2) for this menu item.
  • Do a double button press to scroll to the next menu item, USB Port Enabled.
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all operator panel indicator lights remain on for approximately 2 seconds.

75 Appendix B: Advanced troubleshooting

Page 89 of the Lexmark Optra E312 user manual — 76 Appendix B: Advanced troubleshooting
Page 89 · click to enlarge
Page 89
Lexmark Optra E312 — Printer dimensions diagram (page 89)
Fig. 60 · Printer dimensions

If your printer lights look like this in configuration mode:

USB Port Enabled setting is set to Auto, the factory default.

The Universal Serial Bus (USB) lets you connect a variety of devices, i.e., a printer, to your computer with a single cable.

  • Do a brief button press to scroll through the settings (Off, On, Auto) for this menu item.
  • Do a double button press to scroll to the next menu item, USB NPA Mode.
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all operator panel indicator lights remain on for approximately 2 seconds.

76 Appendix B: Advanced troubleshooting

Page 90 of the Lexmark Optra E312 user manual — 77 Appendix B: Advanced troubleshooting
Page 90 · click to enlarge
Page 90
Lexmark Optra E312 — Printer dimensions diagram (page 90)
Fig. 61 · Printer dimensions

If your printer lights look like this in configuration mode:

USB NPA Mode setting is set to Auto, the factory default.

When USB NPA Mode is enabled, your computer can send print jobs to the printer and query printer status information simultaneously.

  • Do a brief button press to scroll through the settings (Off, On, Auto) for this menu item.
  • Do a double button press to scroll to the next menu item, Parallel Port Enabled.
  • Do a long button press to select and save a setting for this menu. As the setting is saved, all operator panel indicator lights remain on for approximately 2 seconds.

77 Appendix B: Advanced troubleshooting

Page 91 of the Lexmark Optra E312 user manual — 78 Appendix B: Advanced troubleshooting
Page 91 · click to enlarge
Page 91

78 Appendix B: Advanced troubleshooting

Page 92 of the Lexmark Optra E312 user manual — 79 Appendix C: Safety information
Page 92 · click to enlarge
Page 92
Lexmark Optra E312 — Printer dimensions diagram (page 92)
Fig. 62 · Printer dimensions
  • Le produit utilise un laser : ATTENTION : Les commandes, les réglages et l'exécution de toute autre procédure que celle indiquée dans le présent document peuvent entraîner des risques de radiations.
  • If your product is NOT marked with this symbol , it MUST be connected to an electrical outlet that is properly grounded.
  • The power cord must be connected to an electrical outlet that is near the product and easily accessible.
  • Le produit utilise un système d'impression qui chauffe le support d'impression duquel peuvent alors se dégager des émissions. Vous devez consulter les directives générales dans la section appropriée des instructions d'emploi pour savoir comment empêcher que ces émissions ne se produisent.
  • Refer service or repairs, other than those described in the operating instructions, to a professional service person.
  • This product is designed, tested and approved to meet strict global safety standards with the use of specific Lexmark components. The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.
  • Your product uses a laser, exercise CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  • Se il prodotto NON è contrassegnato con questo simbolo DEVE essere collegato lo stesso ad una presa elettrica con messa a terra.
  • Your product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
  • Il cavo di alimentazione deve essere collegato ad una presa elettrica posta nelle vicinanze del prodotto e facilmente raggiungibile.
  • Per la manutenzione o le riparazioni, escluse quelle descritte nelle istruzioni operative, consultare il personale di assistenza autorizzato.
  • Il prodotto è stato progettato, testato e approvato in conformità a severi standard di sicurezza e per l’utilizzo con componenti Lexmark specifici. Le caratteristiche di sicurezza di alcune parti non sempre sono di immediata comprensione. Lexmark non è responsabile per l’utilizzo di parti di ricambio di altri produttori.
  • Si le symbole n'apparaît PAS sur votre produit, ce dernier DOIT être branché sur une prise de courant mise à la terre.
  • Le câble d'alimentation doit être connecté à une prise de courant placée près du produit et facilement accessible.
  • Poiché il prodotto in questione utilizza il laser, considerare il seguente avvertimento: ATTENZIONE: L'uso di dispositivi di controllo o di regolazione, o l'esecuzione di procedure non incluse tra quelle descritte in questa documentazione, può provocare una pericolosa esposizione alle radiazioni.
  • L'entretien et les réparations autres que ceux décrits dans les instructions d'emploi doivent être effectués par le personnel de maintenance qualifié.
  • Ce produit a été conçu, testé et approuvé pour respecter les normes strictes de sécurité globale lors de l'utilisation de composants Lexmark spécifiques. Les caractéristiques de sécurité de certains éléments ne sont pas toujours évidentes. Lexmark ne peut être tenu responsable de l'utilisation d'autres pièces de rechange.
  • Il prodotto in questione utilizza un processo di stampa che riscalda i supporti di stampa; il calore generato può determinare l'emissione di sostanze dannose da parte dei supporti. Leggere attentamente la sezione riportata nelle istruzioni riguardante le operazioni di selezione dei supporti di stampa in modo da evitare la possibilità di emissioni dannose.

79 Appendix C: Safety information

Norme di sicurezza · Consignes de sécurité

Page 94 of the Lexmark Optra E312 user manual — 81 Appendix C: Safety information
Page 94 · click to enlarge
Page 94
  • Aquest producte està dissenyat, comprovat i aprovat per tal d'acomplir les estrictes normes de seguretat globals amb la utililització de components específics de Lexmark. Les característiques de seguretat d'algunes peces pot ser que no sempre siguin òbvies. Lexmark no es responsabilitza de l'us d'altres peces de recanvi.
  • Hvis produktet ditt ikke er merket med dette symbolet, , må det bare kobles til en stikkontakt som er jordet.
  • Ledningen må være koblet til en stikkontakt nær produktet. Stikkontakten må være lett tilgjengelig.
  • El vostre producte funciona amb un làser. Procediu amb PRECAUCIÓ: La utilització de controls, els ajustaments o la realització de procediments distints dels especificats aquí poden donar lloc a una exposició a radiacions perillosa.
  • La bare kvalifisert personale ta seg av service og reparasjon som ikke er direkte beskrevet i bruksanvisningen.
  • Dette produktet er utviklet, testet og godkjent i overensstemmelse med strenge verdensomspennende sikkerhetsstandarder for bestemte Lexmark-deler. Delenes sikkerhetsfunksjoner kan være skjulte. Lexmark er ikke ansvarlig for bruk av uoriginale reservedeler.
  • El vostre producte fa servir un procediment d’impressió que escalfa el mitjà d’impressió, i la calor pot fer que aquest mitjà alliberi emissions. Llegiu atentament l’apartat de les instruccions de funcionament on s’exposen les directrius de selecció del mitjà d’emissió per tal d’evitar la possibilitat d’emissions nocives.
  • Produktet ditt bruker en laser. ADVARSEL: Bruk av styremekanismer, innstillinger eller fremgangsmåter som ikke er beskrevet her, kan resultere i farlig utstråling.
  • Produktet ditt bruker en utskriftsprosess som varmer opp skrivemediet, og varmen kan føre til utslipp. Forsikre deg om at du forstår den delen av bruksanvisningen som omhandler valg av utskriftsmedium, slik at du kan unngå farlige utslipp.
  • Jos tuotteessa ei ole tätä tunnusta, , sen saa kytkeä vain maadoitettuun pistorasiaan.
  • Tuotteen verkkojohto on kytkettävä sitä lähellä olevaan pistorasiaan. Varmista, että kulku pistorasian luo on esteetön.
  • Muut kuin käyttöohjeissa mainitut huoltotai korjaustoimet on jätettävä huoltoedustajalle.
  • Om produkten INTE är märkt med denna symbol MÅSTE den anslutas till ett jordat vägguttag.
  • Tämä tuote on testattu ja hyväksytty. Se täyttää korkeat maailmanlaajuiset turvallisuusvaatimukset, kun siinä käytetään tiettyjä Lexmarkin valmistusosia. Joidenkin osien turvallisuusominaisuudet eivät aina ole itsestään selviä. Lexmark ei vastaa muiden kuin alkuperäisten osien käytöstä.
  • Nätkabeln måste anslutas till ett lättåtkomligt vägguttag i närheten av maskinen.
  • Låt endast utbildad servicepersonal utföra sådan service och sådana reparationer som inte beskrivs i handledningen.
  • Laite sisältää lasertuotteen. Varoitus: Muiden kuin tässä mainittujen säätöjen tai toimien teko voi saattaa käyttäjän alttiiksi vaaralliselle säteilylle.
  • Denna produkt är utformad, testad och godkänd för att uppfylla internationella säkerhetsbestämmelser när den används tillsammans med andra Lexmark-produkter. Säkerhetsegenskaperna för vissa delar är inte helt uppenbara. Lexmark frånsäger sig ansvaret om delar av ett annat fabrikat används.
  • Tulostusmateriaali kuumenee tulostusprosessin aikana. Lämmön vaikutuksesta materiaalista saattaa irrota haitallisia aineita. Voit välttää haitalliset päästöt noudattamalla käyttöohjeissa annettuja tulostusmateriaalien valintaohjeita.
  • Var försiktig - maskinen använder laser. VARNING! Det finns risk att du utsätter dig för hälsovådlig strålning om du använder andra reglage eller justeringar, eller om du utför andra procedurer än de som beskrivs här.
  • Maskinen använder en utskriftsmetod som upphettar utskriftsmaterialet. Hettan kan i vissa fall leda till att materialet avger partiklar. Undvik skadliga partiklar genom att noga läsa det avsnitt i handledningen som beskriver hur man väljer utskriftsmaterial.
  • Se o produto NÃO estiver marcado com este símbolo, , é necessário ligá-lo a uma tomada com ligação à terra.
  • O cabo deve ser ligado a uma tomada localizada perto do produto e facilmente acessível.
  • Para todos os serviços ou reparações não referidos nas instruções de operação, deve contactar um técnico dos serviços de assistência.
  • Si el vostre producte NO està marcat amb el símbol , S’HAURÀ de connectar a una presa elèctrica de terra.
  • Este produto foi concebido, testado e aprovado para satisfazer os padrões globais de segurança na utilização de componentes específicos da Lexmark. As funções de segurança de alguns dos componentes podem não ser sempre óbvias. A Lexmark não é responsável pela utilização de outros componentes de substituição.
  • El cable de potència s’haurà de connectar a una presa de corrent propera al producte i fàcilment accessible.
  • Si heu de fer una reparació que no figuri entre les descrites a les instruccions de funcionament, confieu-la a un professional.

81 Appendix C: Safety information

Show 5 more labels / short text on this page
Sikkerhetsinformasjon · Turvaohjeet · Säkerhetsanvisningar · Informações de Segurança · Informació de Seguretat
Page 96 of the Lexmark Optra E312 user manual — 83 Appendix C: Safety information
Page 96 · click to enlarge
Page 96
Lexmark Optra E312 — Printer dimensions diagram (page 96)
Fig. 63 · Printer dimensions

83 Appendix C: Safety information

Page 97 of the Lexmark Optra E312 user manual — 84 Appendix C: Safety information
Page 97 · click to enlarge
Page 97
Lexmark Optra E312 — Printer dimensions diagram (page 97)
Fig. 64 · Printer dimensions
Lexmark Optra E312 — Printer dimensions diagram (page 97)
Fig. 65 · Printer dimensions

84 Appendix C: Safety information

Page 98 of the Lexmark Optra E312 user manual — 85 Appendix C: Safety information
Page 98 · click to enlarge
Page 98
Lexmark Optra E312 — Printer dimensions diagram (page 98)
Fig. 66 · Printer dimensions

85 Appendix C: Safety information

Page 99 of the Lexmark Optra E312 user manual — 86 Appendix C: Safety information
Page 99 · click to enlarge
Page 99

86 Appendix C: Safety information

Page 100 of the Lexmark Optra E312 user manual — 87 Appendix D: Notices
Page 100 · click to enlarge
Page 100

Notices

Lexmark Optra E312 — Notices diagram (page 100)
Fig. 67 · Notices

Electronic emissions notices

Any questions regarding this compliance information statement should be directed to:

Director of Lab Operations

Lexmark International, Inc. 740 New Circle Road NW Lexington, KY 40550 (606) 232-3000

Federal Communications Commission (FCC) compliance information statement

The Optra E laser printer, type 312, has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada compliance statement

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

The FCC Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm- ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol- lowing measures:

Avis de conformité aux normes d’Industrie Canada

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

  • Reorient or relocate the receiving antenna.

European Community (EC) directives conformity

  • Increase the separation between the equipment and receiver.

This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electro- magnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.

  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult your point of purchase or service representative for additional suggestions.

A declaration of conformity with the requirements of the Directive has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boigny, France.

The manufacturer is not responsible for any radio or television interfer- ence caused by using other than recommended cables or by unautho- rized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate this equip- ment.

This product satisfies the Class B limits of EN 55022 and safety require- ments of EN 60950.

To assure compliance with FCC regulations on electromagnetic interfer- ence for a Class B computing device, use a properly shielded and grounded cable such as Lexmark part number 1329605 for parallel and 12A2405 for USB. Use of a substitute cable not properly shielded and grounded may result in a violation of FCC regulations.

87 Appendix D: Notices

Page 101 of the Lexmark Optra E312 user manual — 88 Appendix D: Notices
Page 101 · click to enlarge
Page 101

Class 1 laser statement label

Lexmark Optra E312 — Printer dimensions diagram (page 101)
Fig. 68 · Printer dimensions

The United Kingdom Telecommunications Act 1984

This apparatus is approved under the approval number NS/G/1234/J/ 100003 for the indirect connections to the public telecommunications sys- tems in the United Kingdom.

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

1-Meter Average Sound Pressure, dBa

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 825.

Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 5 milliwatt gallium arsenide laser operating in the wavelength region of 700-810 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.

Energy Star

Der Drucker erfüllt gemäß amtlicher Bestätigung der USA die Anforderungen der Bestimmung DHHS (Department of Health and Human Services) 21 CFR Teil J für Laserprodukte der Klasse I (1). In anderen Ländern gilt der Drucker als Laserprodukt der Klasse I, der die Anforderungen der IEC (International Electrotechnical Commission) 825 gemäß amtlicher Bestätigung erfüllt.

The EPA ENERGY STAR Computers program is a partnership effort with computer manufacturers to promote the introduction of energy-efficient products and to reduce air pollution caused by power generation.

Companies participating in this program introduce personal computers, printers, monitors, or fax machines that power down when they are not being used. This feature will cut the energy used by up to 50 percent. Lexmark is proud to be a participant in this program.

Laserprodukte der Klasse I gelten als unschädlich. Im Inneren des Druckers befindet sich ein Laser der Klasse IIIb (3b), bei dem es sich um einen Galliumarsenlaser mit 5 Milliwatt handelt, der Wellen der Länge 700-810 Nanometer ausstrahlt. Das Lasersystem und der Drucker sind so konzipiert, daß im Normalbetrieb, bei der Wartung durch den Benutzer oder bei ordnungsgemäßer Wartung durch den Kundendienst Laserbestrahlung, die die Klasse I übersteigen würde, Menschen keines- falls erreicht.

As an Energy Star Partner, Lexmark International, Inc. has determined that this product meets the Energy Star guidelines for energy efficiency.

Laser notices

Avis relatif à l’utilisation de laser

The following laser notice label may be affixed to this printer as shown:

Pour les Etats-Unis : cette imprimante est certifiée conforme aux provi- sions DHHS 21 CFR alinéa J concernant les produits laser de Classe I (1).

88 Appendix D: Notices

Show 6 more labels / short text on this page
Japanese VCCI notice · German acoustics statement · Laser notice · Printing 48 dBa · Idling 35 dBa · Laser
Page 102 of the Lexmark Optra E312 user manual — 89 Appendix D: Notices
Page 102 · click to enlarge
Page 102

Pour les autres pays : cette imprimante répond aux normes IEC 825 rela- tives aux produits laser de Classe I.

Les produits laser de Classe I sont considérés comme des produits non dangereux. Cette imprimante est équipée d’un laser de Classe IIIb (3b) (arséniure de gallium d’une puissance nominale de 5 milliwatts) émet- tant sur des longueurs d’onde comprises entre 700 et 810 nanomètres. L’imprimante et son système laser sont conçus pour impossible, dans des conditions normales d’utilisation, d’entretien par l’utilisateur ou de révi- sion, l’exposition à des rayonnements laser supérieurs à des rayonne- ments de Classe I .

De printer voldoet aan de eisen die gesteld worden aan een laserprodukt van klasse I. Voor de Verenigde Staten zijn deze eisen vastgelegd in DHHS 21 CFR Subchapter J, voor andere landen in IEC 825.

Laserprodukten van klasse I worden niet als ongevaarlijk aangemerkt. De printer is voorzien van een laser van klasse IIIb (3b), dat wil zeggen een gallium arsenide-laser van 5 milliwatt met een golflengte van 700- 810 nanometer. Het lasergedeelte en de printer zijn zo ontworpen dat bij normaal gebruik, bij onderhoud of reparatie conform de voorschriften, nooit blootstelling mogelijk is aan laserstraling boven een niveau zoals voorgeschreven is voor klasse 1.

Avvertenze sui prodotti laser

Questa stampante è certificata negli Stati Uniti per essere conforme ai requisiti del DHHS 21 CFR Sottocapitolo J per i prodotti laser di classe 1 ed è certificata negli altri Paesi come prodotto laser di classe 1 conforme ai requisiti della norma CEI 825.

Printeren er godkendt som et Klasse I-laserprodukt, i overenstemmelse med kravene i IEC 825.

I prodotti laser di classe non sono considerati pericolosi. La stampante contiene al suo interno un laser di classe IIIb (3b) all’arseniuro di gallio della potenza di 5mW che opera sulla lunghezza d’onda compresa tra 700 e 810 nanometri. Il sistema laser e la stampante sono stati progettati in modo tale che le persone a contatto con la stampante, durante il nor- male funzionamento, le operazioni di servizio o quelle di assistenza tec- nica, non ricevano radiazioni laser superiori al livello della classe 1.

Klasse I-laserprodukter betragtes ikke som farlige. Printeren indeholder internt en Klasse IIIB (3b)-laser, der nominelt er en 5 milliwatt galliu- marsenid laser, som arbejder på bølgelængdeområdet 700-810 nanome- ter. Lasersystemet og printeren er udformet således, at mennesker aldrig udsættes for en laserstråling over Klasse I-niveau ved normal drift, brugervedligeholdelse eller obligatoriske servicebetingelser.

Tämä kirjoitin on Yhdysvalloissa luokan I (1) laserlaitteiden DHHS 21 CFR Subchapter J -määrityksen mukainen ja muualla luokan I laserlait- teiden IEC 825 -määrityksen mukainen.

Se certifica que, en los EE.UU., esta impresora cumple los requisitos para los productos láser de Clase I (1) establecidos en el subcapítulo J de la norma CFR 21 del DHHS (Departamento de Sanidad y Servicios) y, en los demás países, reúne todas las condiciones expuestas en la norma IEC 825 para productos láser de Clase I (1).

Luokan I laserlaitteiden ei katsota olevan vaarallisia käyttäjälle. Kirjoit- timessa on sisäinen luokan IIIb (3b) 5 milliwatin galliumarsenidilaser, joka toimii aaltoalueella 700 - 810 nanometriä. Laserjärjestelmä ja kirjoitin on suunniteltu siten, että käyttäjä ei altistu luokan I määrityksiä voimak- kaammalle säteilylle kirjoittimen normaalin toiminnan, käyttäjän teke- mien huoltotoimien tai muiden huoltotoimien yhteydessä.

Los productos láser de Clase I no se consideran peligrosos. La impresora contiene en su interior un láser de Clase IIIb (3b) de arseniuro de galio de funcionamiento nominal a 5 milivatios en una longitud de onda de 700 a 810 nanómetros. El sistema láser y la impresora están diseñados de forma que ninguna persona pueda verse afectada por ningún tipo de radiación láser superior al nivel de la Clase I durante su uso normal, el manten- imiento realizado por el usuario o cualquier otra situación de servicio técnico.

LUOKAN 1 LASERLAITE

VAROITUS! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylit- tävälle näkymättömälle lasersäteilylle.

KLASS 1 LASER APPARAT

VARNING! Om apparaten används på annat sätt än i denna bruksan- visning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.

A impressora está certificada nos E.U.A. em conformidade com os requi- sitos da regulamentação DHHS 21 CFR Subcapítulo J para a Classe I (1) de produtos laser. Em outros locais, está certificada como um produto laser da Classe I, em conformidade com os requisitos da norma IEC 825.

VARO! Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymät- tömälle lasersäteilylle. Älä katso säteeseen.

VARNING! Osynlig laserstrålning när denna del är öppnad och spärren är urkopplad. Betrakta ej strålen.

Os produtos laser da Classe I não são considerados perigosos. Interna- mente, a impressora contém um produto laser da Classe IIIb (3b), desig- nado laser de arseneto de potássio, de 5 milliwatts ,operando numa faixa de comprimento de onda entre 700 e 810 nanómetros. O sistema e a impressora laser foram concebidos de forma a nunca existir qualquer possiblidade de acesso humano a radiação laser superior a um nível de Classe I durante a operação normal, a manutenção feita pelo utilizador ou condições de assistência prescritas.

Denna skrivare är i USA certifierad att motsvara kraven i DHHS 21 CFR, underparagraf J för laserprodukter av Klass I (1). I andra länder upp- fyller skrivaren kraven för laserprodukter av Klass I enligt kraven i IEC 825.

89 Appendix D: Notices

Show 5 more labels / short text on this page
Laserinformatie · Lasermeddelelse · Huomautus laserlaitteesta · Declaração sobre laser · Laser-notis
Page 103 of the Lexmark Optra E312 user manual — 90 Appendix D: Notices
Page 103 · click to enlarge
Page 103

Laserprodukter i Klass I anses ej hälsovådliga. Skrivaren har en inbyggd laser av Klass IIIb (3b) som består av en laserenhet av gallium-arsenid på 5 milliwatt som arbetar i våglängdsområdet 700-810 nanometer. Laser- systemet och skrivaren är utformade så att det aldrig finns risk för att någon person utsätts för laserstrålning över Klass I-nivå vid normal användning, underhåll som utförs av användaren eller annan föreskriven serviceåtgärd.

Lexmark Optra E312 — Printer dimensions diagram (page 103)
Fig. 69 · Printer dimensions

Skriveren er godkjent i USA etter kravene i DHHS 21 CFR, underkapittel J, for klasse I (1) laserprodukter, og er i andre land godkjent som et Klasse I-laserprodukt i samsvar med kravene i IEC 825.

Klasse I-laserprodukter er ikke å betrakte som farlige. Skriveren inne- holder internt en klasse IIIb (3b)-laser, som består av en gallium-arsenla- serenhet som avgir stråling i bølgelengdeområdet 700-810 nanometer. Lasersystemet og skriveren er utformet slik at personer aldri utsettes for laserstråling ut over klasse I-nivå under vanlig bruk, vedlikehold som utføres av brukeren, eller foreskrevne serviceoperasjoner.

Avís sobre el làser

Segons ha estat certificat als Estats Units, aquesta impressora compleix els requisits de DHHS 21 CFR, apartat J, pels productes làser de classe I (1), i segons ha estat certificat en altres llocs, és un producte làser de classe I que compleix els requisits d’IEC 825.

Lexmark Optra E312 — Printer dimensions diagram (page 103)
Fig. 70 · Printer dimensions

Els productes làser de classe I no es consideren perillosos. Aquesta impressora conté un làser de classe IIIb (3b) d’arseniür de gal.li, nominalment de 5 mil.liwats, i funciona a la regió de longitud d’ona de 700-810 nanòmetres. El sistema làser i la impressora han sigut concebuts de manera que mai hi hagi exposició a la radiació làser per sobre d’un nivell de classe I durant una operació normal, durant les tasques de manteniment d’usuari ni durant els serveis que satisfacin les condicions prescrites.

Lexmark Optra E312 — Printer dimensions diagram (page 103)
Fig. 71 · Printer dimensions

90 Appendix D: Notices

Show 4 more labels / short text on this page
Chinese laser notice · Laser-melding · Korean laser notice · Japanese laser notice
Page 104 of the Lexmark Optra E312 user manual — 91 Statement of Limited Warranty
Page 104 · click to enlarge
Page 104

Statement of Limited Warranty

Lexmark International, Inc., Lexington, KY

This warranty applies to the United States and Canada. For customers outside the U.S. and Canada, refer to the country-specific warranty information that came with your printer.

Optra E312

This Statement of Limited Warranty applies to this product if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark remarketer, referred to in this statement as “Remarketer.”

Warranty

  • Lexmark warrants that this product:
  • Is manufactured from new parts, or new and serviceable used parts, which perform like new parts,
  • Is free from defects in material and workmanship,
  • Conforms to Lexmark’s official published specifications, and
  • Is in good working order.

If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair without charge.

If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was designed. To obtain warranty service, you may be required to present the feature or option with the product.

91 Statement of Limited Warranty

Page 105 of the Lexmark Optra E312 user manual — 92 Statement of Limited Warranty
Page 105 · click to enlarge
Page 105

If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.

Warranty Service

The warranty period is 12 months and starts on the date of original purchase as shown on the purchase receipt.

To obtain warranty service you may be required to present proof of original purchase. Warranty service will be provided at a Lexmark designated location. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the designated location.

When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item. The replacement item assumes the remaining warranty period of the original product.

Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, or damaged beyond repair. Also, such product must be free of any legal obligation or restrictions that prevent its exchange.

Before you present this product for warranty service, remove all programs, data, and removable storage media.

For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area, please contact Lexmark at 1-800-LEXMARK (1-800-539-6275), or on the World Wide Web at http://www.lexmark.com

Free remote technical support is provided for this product throughout its warranty period. Lex- mark offers a variety of extended warranty programs that include an extension of technical sup- port. For products no longer covered by a Lexmark warranty, technical support may only be available for a fee.

92 Statement of Limited Warranty

Page 106 of the Lexmark Optra E312 user manual — 93 Statement of Limited Warranty
Page 106 · click to enlarge
Page 106

Extent of Warranty

We do not warrant uninterrupted or error-free operation of a product.

  • Warranty service does not include repair of failures caused by:
  • modification or attachments
  • accidents or misuse
  • unsuitable physical or operating environment
  • maintenance by anyone other than Lexmark or a Lexmark authorized servicer
  • operation of a product beyond the limit of its duty cycle
  • failure to have installed a maintenance kit as specified (if applicable)
  • use of printing media outside of Lexmark specifications
  • use of other than Lexmark supplies (such as toner cartridges, inkjet cartridges, and ribbons)
  • use of other than Lexmark product or component

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.

Limitation of Liability

Your sole remedy under this Statement of Limited Warranty is set forth in this section. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this Statement of Limited Warranty, you may recover actual damages up to the limit set forth in the following paragraph.

Lexmark's liability for actual damages from any cause whatsoever will be limited to the greater of 1) $5,000 or 2) the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. In no event will Lexmark be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.

This limitation of remedies also applies to any developer of materials supplied to Lexmark. Lexmark’s and the developer’s limitations of remedies are not cumulative. Such developer is an intended beneficiary of this limitation.

93 Statement of Limited Warranty

Page 107 of the Lexmark Optra E312 user manual — 94 Statement of Limited Warranty
Page 107 · click to enlarge
Page 107

Additional Rights

Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

94 Statement of Limited Warranty

Page 108 of the Lexmark Optra E312 user manual — X-1 Glossary
Page 108 · click to enlarge
Page 108

Glossary

1200 Image Quality. A print resolution setting that allows the printer to vary the size of each printed pixel, thereby producing a continuous tone effect. This setting improves the print quality of graphic fills, images and halftones.

bidirectional communication. Two-way communication between your printer and a computer, using Network Printing Alliance Protocol (NPAP 1.0 standard).

bin. See output bin.

A

bitmapped font. Predefined pattern of bits that represent a typeface at a specific size, style and resolution.

A4. Paper measuring 210 x 297 mm.

A5. Paper measuring 148 x 210 mm.

Busy. A printer state in which the printer is processing data or printing pages.

application. See software application.

attendance message. A message that indicates a printer problem. The printer requires operator intervention before it can continue processing.

C5. Envelope measuring 162 x 229 mm.

automated fax system. Lexmark’s quick turnaround system for providing customers product information, technical tips and printer driver information. The automated attendant walks the customer through the steps necessary to receive information by fax.

Centronics parallel interface. A standard for connecting printers and other peripheral devices to a computer. It defines the plug, socket and electrical signals that are used for controlling the transmission of data.

configuration. (1) The arrangement of a computer system, printer or network. (2) The devices and programs that make up a system, subsystem or network.

B

B5. (1) Envelope measuring 176 x 250 mm. (2) Paper measuring 182 x 257 mm.

X-1 Glossary

Page 109 of the Lexmark Optra E312 user manual — X-2 Glossary
Page 109 · click to enlarge
Page 109

flash memory. Optional memory you can install in the printer that provides non-volatile storage for downloaded fonts, symbol sets or macros.

D

data stream. Print data and printer control information flowing from the host system (computer) to the printer without interruption.

font. A family or set of characters that have common visual characteristics, such as size, weight and style.

default. An attribute, value or setting that is assumed when none is explicitly specified.

fuser. The part of the printer that uses heat and pressure to make toner adhere to the paper.

defrag. To free up unused space. To defrag flash memory, the unused space or gaps are moved to the end of the memory, creating additional space.

G

g/m². Grams per square meter. Metric measurement for paper weight.

DL. Envelope measuring 110 x 220 mm.

download. To transfer information, such as fonts, from a diskette or other device to your computer or printer for temporary or permanent storage.

H

hex trace. A way to isolate printing problems by showing you, in a hexadecimal and character representation of a print job, what information your printer is receiving.

dpi. Dots per inch. See resolution.

driver. See printer driver.

E

emulation. Imitation of a printer processing language; for example, PCL 5 emulation imitates the printer language used with the Hewlett- Packard LaserJet printer.

indicator lights. The 6 lights on the operator panel that provide status, attendance and service information.

interface. The connection between the computer and the printer.

executive paper. Paper measuring 7.25 x 10.5 in.

F

landscape orientation. Printed page orientation in which the print runs along the long edge of the paper.

factory default. Printer setting defined when the printer is manufactured.

Fastbytes protocol. A parallel printer protocol that enables the printer to receive information at faster transmission rates than normal.

leading edge. The edge of the printer page that exits the printer first.

legal. Paper measuring 8.5 x 14 in.

X-2 Glossary

Page 110 of the Lexmark Optra E312 user manual — X-3 Glossary
Page 110 · click to enlarge
Page 110

letter. Paper measuring 8.5 x 11 in.

output bin. Any paper exit area. The default is the standard output bin, on top of the printer, which allows the paper to exit face down and collated.

M

macro. A collection of commands grouped together and temporarily or permanently stored in printer memory.

overlay. Background text or graphics intended to appear the same in each file where the overlay is applied.

manual feed. Feeding one sheet of media (paper, envelope, transparency) into the printer at a time.

P

pages per minute (ppm). The number of typical pages of text that can be printed in one minute.

MarkVision. A printer utility that works with the printer’s bidirectional communication capability to provide continuous printer status and let you configure multiple printers from a single setup file.

parallel interface. A bidirectional interface for exchanging data between the computer and the printer.

MB. Megabyte; 1,048,576 bytes.

portrait orientation. Printed page orientation in which the print runs across the short edge of the paper.

media. Any materials you print on, such as paper, envelopes, labels and transparencies.

print cartridge. The replaceable unit inside the printer that contains the toner supply.

menu. The choices for displaying, altering or testing printer features and settings.

printer driver. A program that translates the language of a software application to the language of the printer so the two can communicate data.

O

operating system. The basic software which provides the low-level functions needed to operate your computer, such as booting up.

printer language. A set of defined commands (such as PCL or PostScript) to which the printer responds.

Operation ReSource. Lexmark’s process established to recycle toner cartridges and print units.

protocol. A set of rules governing the communication and the transfer of data between two or more devices.

operator panel. The 6 lights and 1 button on the printer that are used to change printer settings and display printer status.

R

orientation. A page description defining whether the printed text runs along the short edge (portrait) or the long edge (landscape) of the paper.

Ready. State of the printer in which it can receive, process and print data.

X-3 Glossary

Page 111 of the Lexmark Optra E312 user manual — X-4 Glossary
Page 111 · click to enlarge
Page 111

reset. Clears the printer buffer and all temporary settings, and returns to the initial power-on state.

toner. The material that adheres to the paper or other media to create the printed page.

TrueType fonts. Fonts that use a single font outline for both screen display and printing. You can use TrueType fonts in Windows applications and scale them to any height. They print exactly as they appear on the screen.

resolution. A measure of the sharpness of a printed image, expressed in the number of dots per inch (dpi).

S

U

scalable font. A font whose characters are stored only as outlines so it is easy to change (or scale) the size of the characters (measured in points).

USB (Universal Serial Bus). A communications architecture that lets a computer interconnect with a variety of peripherals with a single cable.

service message. A printer message that indicates the printer needs service.

user default. Printer setting selected by a user that remains in effect until a new user default is chosen.

setting. Values you choose from printer menus or software applications that control printer operation and the appearance of the printed page.

setup utility. A program shipped with your printer to install printer drivers, test printer setup, and complete the setup of printer options.

software application. Any program loaded on your computer used to perform a specific task, such as word processing or data compiling.

standard protocol. A parallel printer protocol where the printer receives information sent from the computer at a normal transmission rate.

status message. A printer message that provides information on the state of the printer.

system board. The printer’s main circuit board.

T

test page. A printed page that lists information about your printer.

X-4 Glossary

Page 116 of the Lexmark Optra E312 user manual — www.lexmark.com
Page 116 · click to enlarge
Page 116
Lexmark Optra E312 — Index diagram (page 116)
Fig. 72 · Index

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2000 Lexmark International, Inc. 740 West New Circle Road Lexington, Kentucky 40550

www.lexmark.com

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Display codes

Error codes

What the fault codes shown on the display mean and how to clear them.

CodeMeaningFix
C5Envelope measuring 162 x 229 mm. p.108
Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Characters appear light or blurred.• Make sure you removed the sealing tape from the print cartridge. • Replace the print cartridge. p.17
Printer seems to be printing, but pages are blank.• The print cartridge may be out of toner. Replace the cartridge. • The print cartridge may be defective. Replace the cartridge. • Make sure you removed the sealing tape from the print cartridge. p.17
Printer is on, but nothing prints. Jobs are not printing and the Error light is on solid.• Make sure the print cartridge is installed. p.17
Unexpected characters print or characters are missing.• Make sure the parallel cable or USB cable is firmly plugged in at the back of the printer. p.20
You are connected to the USB port, but the printer will not print.• Make sure you are using Windows 98 or Windows 2000. p.20
Auto Setup fails in the PostScript Printer Description (PPD) File box• Re-install the printer PPD from the CD. p.22
Toner smudges appear on the front or back of the page.• Make sure the paper is straight and unwrinkled. p.25
Paper sticks together/printer feeds multiple sheets of paper.• Remove the paper from the paper feeder and fan the paper. • Make sure there isn’t too much paper in the paper feeder. The automatic paper feeder holds up to 150 sheets, depending on the thickness of the paper. p.25
Paper fails to feed from the automatic paper feeder.• Remove the paper from the paper feeder and fan the paper. p.25
Paper skews or buckles.• Make sure there isn’t too much paper in the paper feeder. The automatic paper feeder holds up to 150 sheets, depending on the thickness of the paper. • Make sure the paper guides are properly positioned against the edges of the paper. p.25
The operator panel lights do not come on when the printer is turned on.• Make sure the power cord is firmly plugged in at the back of the printer and at the wall outlet. p.26
Paper sticks together/printer feeds multiple sheets of paper. Paper skews or buckles.• Make sure you are using recommended paper/other media (see Paper types and sizes). p.49
Envelopes fail to feed correctly.• Make sure the envelopes are loaded in the center of the feeder. • Try a different kind. Envelopes designed for laser printers produce better results. p.49
Light or blurred characters.• Make sure you removed the sealing tape from the print cartridge. • Hot/humid or cold/dry weather conditions may affect how well toner adheres to paper. Select the next darker print setting. • If Toner Saver is on, turn it off using MarkVision or your printer driver. • Remove the print cartridge, shake it from side-to-side to redistribute the toner, and reinsert it. • Run Engine Clean Cycle to remove any toner that may have accumulated (see Engine clean cycle). • Make sure you are using recommended paper/other media (see Paper types and sizes). • Use MarkVision to define the Custom Type setting for media type, media texture or media weight. • Replace the print cartridge. p.50
Toner smudges appear on the front or back of the page.• Run Engine Clean Cycle to remove any toner that may have accumulated (Engine clean cycle). • Make sure the paper is straight and unwrinkled. • Replace the print cartridge. p.50
Vertical or horizontal streaks appear on the page.• Run Engine Clean Cycle to remove any toner that may have accumulated (Engine clean cycle). • Replace the print cartridge. p.50
Printer has missing or damaged parts.• Inside the U.S., call the number listed on your printer registration card. • Outside the U.S., contact your point of purchase. p.51
Power is turned on at a power strip but the Ready light is not on.• Be sure the printer power switch is on too. p.51
Printer is on, but nothing prints.• Make sure the print cartridge is installed. • Make sure the parallel cable is firmly plugged into the connector on the back of the printer. • Print a test page (do a brief button press) to determine if the problem is with the printer or the computer. — If you can print a test page, the problem is in the computer or the software application. — If you cannot print a test page, call the Lexmark service number listed on the printer registration card. p.51
Printer does not print even though a paper jam has been cleared.• Open and close the printer cover to restart the printer. p.51
Unexpected characters print or characters are missing.• Make sure you are using the correct printer driver. • Select Hex Trace Mode from the Special Function Menu to determine what the problem is. • Restore factory defaults (Reset user defaults). p.51
While in PostScript Level 2 emulation, the printer is flushing data (Data and Error indicator lights are blinking).• Make sure you are using the correct PostScript driver. • The printer doesn’t have enough memory to print the job. Install more memory (see Installing a printer memory card). p.51
While in MarkVision, the Press Button light is on.• The printer is off-line. Press and hold the operator panel button for 3 seconds to reset the printer. p.51

Ask about the Lexmark Optra E312

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark Optra E312

Be the first to ask — other owners or our team will answer.

Original document

Lexmark Optra E312 manual PDF

116 pages·4.6 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…