
User’s Reference
January 2001





The following illustrations show a Lexmark™ T620 and T622 standard network model configuration and a fully configured printer. If you have attached paper handling options to your printer, it may look more like the fully configured model. For information on other possible configurations, refer to the Setup Guide.
Standard network model configuration Fully configured


Tray 2* (250 or 500 sheets)
Tray 1 (integrated tray)
Tray 3* (250 or 500 sheets)
Tray 2 (optional in non-network models)
Tray 1 (integrated tray)
Tray 4* (250 or 500 sheets)
Tray 5* (2000-sheet drawer)

This section contains information about understanding the operator panel, changing printer settings, and understanding operator panel menus.
You can change most printer settings from your software application or printer driver. Settings you change from the application or printer driver apply only to the job you are preparing to send to the printer.
Changes made to printer settings from a software application override changes made from the printer operator panel.
If you cannot change a setting from your application, use the printer operator panel or the remote operator panel available from MarkVision™. Changing a printer setting from the printer operator panel or from MarkVision makes that setting the user default.
The printer operator panel has a 2-line by 16-character liquid crystal display (LCD), five buttons, and one indicator light.
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
The indicator light gives information about the status of your printer. If the light is:
Light

Use the five operator panel buttons to open a menu, scroll through a list of values, change printer settings, and respond to printer messages.
The numbers 1 through 6 appear beside the operator panel buttons; these numbers are used to enter personal identification numbers (PIN) for Print and Hold jobs. For more information, see Using the Print and Hold function.
The following information describes the functions of each button.
panel.

From the operator panel, you can select menu items and associated values to print your jobs successfully. You can also use the panel to alter the setup and operating environment of the printer. See Using printer menus for an explanation of all the menu items.
You can modify printer settings by:
To select a new value as a setting:
1 From a Ready status message, press Menu. The menu names appear.
2 Continue to press and release Menu until you see the menu you need.
3 Press Select to select the menu or menu item displayed on the second line of the display.
– If the selection is a menu, the menu is opened and the first printer setting in the menu appears. – If the selection is a menu item, the default setting for the menu item appears. (The current user default setting has an asterisk [*] beside it.)
Each menu item has a list of values for the menu item. A value can be:
– A phrase or word to describe a setting – A numerical value that can be changed – An On or Off setting
4 Press Menu to move to the value you need.
5 Press Select to select the value on the second line of the operator panel. An asterisk appears beside the value to indicate that it is now the user default setting. The new setting appears for one second, clears, displays the word Saved, and then displays the previous list of menu items.
6 Press Return to go back to previous menus. Make additional menu selections to set new default settings. Press Go if this is the last printer setting to change.
User default settings remain in effect until you save new settings or restore the factory defaults. Settings you choose from your software application can also change or override the user default settings you select from the operator panel.

Complete the following steps to print a list of the current user default settings and installed printer options:
1 Make sure the printer power is on and the Ready status message appears.
2 Press Menu until you see Utilities Menu, and then press Select.
3 Press Menu until you see Print Menus, and then press Select.
The message Printing Menu Settings appears and remains until the page prints. The printer returns to Ready when the page or pages finish printing.
If a message appears, see Understanding printer messages for more information.
The diagram in Using printer menus shows the menu items in each menu.
An asterisk (*) next to a value indicates the factory default setting. Factory defaults may differ for different countries.
Factory defaults are the function settings in effect the first time you turn your printer on. These remain in effect until you change them. Factory defaults are restored if you select the Restore value for the Factory Defaults menu item in the Utilities Menu. See Utilities Menu for more information.
When you select a new setting from the operator panel, the asterisk moves next to the selected setting to identify it as the current user default.
User defaults are the settings you select for different printer functions and store in printer memory. Once stored, these settings remain active until new ones are stored or the factory defaults are restored.
select from the operator panel.
If your printer is configured as a network printer available to a number of users, Menus Disabled may appear when you press Menu from the Ready state. Disabling the menus prevents users from using the operator panel to inadvertently change a printer default that has been set by the person managing the printer. You can still use Print and Hold features, clear messages, and select items from the Job Menu when printing a job, but you cannot change other printer settings. You can, however, use your printer driver to override printer defaults and select settings for individual print jobs.

To disable the operator panel menus so that changes cannot be made to the printer default settings:
1 Turn the printer off.
Print and Hold functionality.
2 Press and hold Select and Return and turn the printer on.
3 Release the buttons when you see Performing Self Test.
Config Menu appears on the first line of the display.
4 Press Menu until you see Panel Menus, and then press Select.
Disable appears on the second line of the display.
5 Press Select.
Locking Menus appears briefly.
6 Press Menu until you see Exit Config Menus, and then press Select.
The menus are disabled. If you press Menu, the message Menus Disabled appears.
To enable the menus:
1 Repeat steps 1 through 4.
2 Press Menu until you see Enable.
3 Continue with steps 5 and 6.

When sending a job to the printer, you can specify in the driver that you want the printer to hold the job in memory. When you are ready to print the job, you must go to the printer and use the operator panel menus to identify which held job you want to print.
recommend a minimum of 32MB available printer memory and a hard disk.
To learn more about this function, click a topic:
Once held jobs are stored in printer memory, you can use the printer operator panel to specify what you want to do with one or more of the jobs. You can select either Confidential Job or Held Jobs (Repeat Print, Reserve Print, and Verify Print jobs) from the Job Menu. If you select Confidential Job, you must enter the personal identification number (PIN) you specified in the driver when you sent the job. See Confidential jobs for more information.
From either the Confidential Job or the Held Jobs menu items, you have five choices:

1 To access held jobs from the operator panel:
– If the printer is Busy, press Menu and the Job Menu appears. – If the printer is Ready, continue to step 2.
2 Press Menu until you see Held Jobs or Confidential Job on the operator panel display, depending on the type of job you want to access.
3 Press Select.
User Name appears on the first line of the operator panel. The second line displays the names of users currently associated with Print and Hold jobs.
4 Press Menu until you see your user name.
Confidential jobs for more information.
5 Press Select.
6 Press Menu until the action you want to take is on the second line of the operator panel (Print A Job, Delete A Job, and so on).
7 Press Select.
– If you are looking for a particular job, press Menu to scroll through the list of available jobs, and press Select when the correct job is displayed. An asterisk (*) appears next to the job name indicating you have chosen to print or delete that job. – If you are prompted to enter the number of copies you want to print, use the Menu button to increase or decrease the number on the display, and then press Select.
8 Press Go to print or delete specific jobs you have marked.
The printer briefly shows messages indicating what Print and Hold functions it is performing.
If the symbol appears on the display, it indicates that the printer had trouble formatting one or more of the held jobs. These formatting problems are most commonly the result of insufficient printer memory or invalid data that might cause the printer to flush the job.
When a symbol appears next to a held job, you can:
If formatting errors are a recurring problem with held jobs, your printer may require more memory.

If you send a Repeat Print job, the printer prints all requested copies of the job and stores the job in memory so you can print additional copies later. You can print additional copies as long as the job remains stored in memory.
requires extra memory to process additional held jobs.
If you send a Reserve Print job, the printer does not print the job immediately, but stores the job in memory so you can print the job later. The job is held in memory until you delete it from the Held Jobs menu. Reserve Print jobs may be deleted if the printer requires extra memory to process additional held jobs.
See Printing and deleting held jobs for information.
If you send a Verify Print job, the printer prints one copy and holds the remaining copies you requested from the driver in printer memory. Use Verify Print to examine the first copy to see if it is satisfactory before printing the remaining copies.
See Printing and deleting held jobs if you need help printing the additional copies stored in memory.
When you send a job to the printer, you can enter a personal identification number (PIN) from the driver. The PIN must be four digits using the numbers 1–6. The job is then held in printer memory until you enter the same four-digit PIN from the printer operator panel and choose to print or delete the job. This ensures that the job does not print until you are there to retrieve it, and no one else using the printer can print the job.
When you select Confidential Job from the Job Menu and then select your user name, the following prompt is displayed:

Use the buttons on the operator panel to enter the four-digit PIN associated with your confidential job. The numbers next to the button names identify which button to press for each digit (1–6). As you enter the PIN, asterisks are displayed on the operator panel to ensure confidentiality.
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
If you enter an invalid PIN, the message No Jobs Found. Retry? appears. Press Go to reenter the PIN, or press Stop to exit the Confidential Job menu.
When you enter a valid PIN, you have access to all print jobs matching the user name and PIN you entered. The print jobs matching the PIN you entered appear on the display when you enter the Print A Job, Delete A Job, and Print Copies menu items. You can then choose to print or delete jobs matching the PIN you entered. (See Printing and deleting held jobs for more information.) After printing the job, the printer deletes the confidential job from memory.
Enter PIN · =****

To cancel a print job:
1 Press Menu. Job Menu appears on the first line of the display and Cancel Job appears on the second line.
2 Press Select.
Canceling Job briefly appears in the display. The printer finishes printing any page already being printed, and then stops. The printer returns to the Ready state.

Folio and statement sizes are not available in the Paper Size menu until Size Sensing is turned off. To turn off Size Sensing:
1 Press and hold the Select and Return buttons while you turn the printer on.
2 Release the buttons when Performing Self Test appears on the display.
The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.
3 Press Menu until you see Size Sensing, and then press Select.
Tray 1 Sensing appears on the second line of the display.
4 Press Menu to select the input option that will hold the folio or statement size paper, and then press Select.
The first line of the display shows the selected input option and the second line shows the current setting.
5 Press Menu to change the setting to Off, and then press Select.
SAVED appears briefly on the display, and then is replace by Config Menu on the first line and Size Sensing on the second line.
6 Press Menu until you see Exit Config Menu, and then press Select.
7 Activating Menu Changes appears briefly, followed by Performing Self Test. The printer returns to the Ready state.

The print quality and feed reliability of your printer and options can vary with the type and size of print material you use. This section provides guidelines for each type of print material. For information on card stock and labels, refer to the Card Stock & Label Guide located on Lexmark’s Web site at www.lexmark.com.
Always print samples on the print material you are considering before buying large quantities.
Click a topic for more information:
The following paper characteristics affect print quality and reliability. We recommend that you keep these guidelines in mind when evaluating new paper stock.
For detailed information, refer to the Card Stock & Label Guide located on the Lexmark Web site at www.lexmark.com.
The printer can automatically feed paper weights from 60 to 176 g/m2 (16 to 47 lb bond) grain long. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing paper jams. For best performance, use 75 g/m2 (20 lb bond) grain long paper. To use paper narrower than 182 x 257 mm (7.2 x 10.1 in.), we recommend that the weight be greater than or equal to 90 g/m2 (24 lb bond).

Curl is the tendency of paper to curve at its edges. Excessive curl can cause paper feeding problems. Curl usually occurs after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in humid conditions, even in the paper tray, can contribute to paper curling.
The degree of smoothness of paper directly affects print quality. If the paper is too rough, the toner does not fuse to the paper properly, resulting in poor print quality. If the paper is too smooth, it can cause paper feeding problems. Smoothness needs to be between 100 and 300 Sheffield points; however, smoothness between 100 and 175 Sheffield points produces the best print quality.
The amount of moisture in the paper affects both print quality and the ability of the printer to feed the paper properly. Leave the paper in its original wrapper until you are ready to use it. This limits the exposure of the paper to moisture changes that can degrade its performance.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60 to 176 g/m2 (16 to 47 lb bond) paper, grain long fibers are recommended. For papers heavier than 176 g/m2 (47 lb bond), grain short is preferred. For the multipurpose feeder, 60 to 135 g/m2 (16 to 36 lb bond) paper, grain long fibers are recommended. For the multipurpose feeder, papers heavier than 135 g/m2 (36 lb bond), grain short is preferred.
Most high-quality xerographic paper is made from 100% chemically pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton possess characteristics that can result in degraded paper handling.
To ensure the best print quality and feed reliability, use 75 g/m2 (20 lb) xerographic paper. Business papers designed for general business use may also provide acceptable print quality.
Always print several samples before buying large quantities of any type of paper. When choosing any papers, consider the weight, fiber content, and color of the paper.
The laser printing process heats paper to high temperatures of 225°C (437°F) for Magnetic Ink Character Recognition (MICR) applications, and 205°C (401°F) for non-MICR applications. Use only papers that are able to withstand these temperatures without discoloring, bleeding, or releasing hazardous emissions. Check with the manufacturer or vendor to determine whether the paper you’ve chosen is acceptable for laser printers.

The following papers are not recommended for use with the printer:
In some cases, you can adjust registration with your software application to successfully print on these forms.
Use the following guidelines when selecting preprinted forms and letterhead paper for the printer:
Use papers printed with heat-resistant inks designed for use in xerographic copiers. The ink must withstand temperatures of 225°C (437°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in the toner. Inks that are oxidation-set or oil-based should meet these requirements. Latex inks might not meet these requirements. If you are in doubt, contact your paper supplier.

Prepunched paper brands can differ in the number and placement of holes and in manufacturing techniques.
Use the following guidelines when selecting and using prepunched paper:
Proper paper loading helps prevent paper jams and ensure trouble-free printing.
To help avoid paper jams or poor print quality:

When printing on envelopes:
The laser printing process heats envelopes to a temperature of 205°C (401°F). Use only envelopes that are able to withstand these temperatures without sealing, excessive curling, wrinkling, or releasing hazardous emissions. If you have any doubts about the envelopes you are considering using, check with the envelope supplier.
For best performance, use envelopes made from 75 g/m2 (20 lb bond) paper. You can use up to 105 g/ m2 (28 lb bond) weight for the multipurpose feeder or 105 g/m2 (28 lb bond) weight for the envelope feeder as long as the cotton content is 25% or less. Envelopes with 100% cotton content must not exceed 90 g/m2 (24 lb bond) weight.
To minimize jams, do not use envelopes that:
The printer can print on many labels designed for use with laser printers. These labels are supplied in letter size and A4 size sheets.
When printing on labels:

T622 printers require a special fuser cleaner for label applications in order to optimize feed reliability. See Ordering supplies for information on obtaining a label fuser cleaner.
After continuously printing approximately 10,000 page sides of labels (or each time you replace the print cartridge), complete the following steps to maintain printer feeding reliability:
1 Print five sheets of paper.
2 Wait approximately five seconds.
3 Print five more sheets of paper.
For detailed information on label printing, characteristics, and design, refer to the Card Stock & Label Guide, available on Lexmark Web site at www.lexmark.com.
Card stock is single-ply and has a large array of properties. The orientation of paper fibers, moisture content, thickness, and texture can all affect printing on card stock. See Paper specifications for information on the preferred weight for the grain direction of print materials.
When printing on card stock:
After printing approximately 10,000 page sides of card stock (or each time you replace the print cartridge), complete the following steps to maintain printer feeding reliability:
1 Print five sheets of paper.
2 Wait approximately five seconds.
3 Print five more sheets of paper.
For more information, refer to the Card Stock & Label Guide, available on the Lexmark Web site at www.lexmark.com.

The printer can print directly on transparencies designed for use in laser printers. Print quality and durability depend on the transparency used. Always print samples on the transparencies you are considering before buying large quantities.
The Paper Type setting should be set to Transparency to help prevent jams. (See Paper Type for detailed information about this setting.) Check with the manufacturer or vendor to determine whether your transparencies are compatible with laser printers that heat transparencies to 212°C (414°F). Use only transparencies that are able to withstand these temperatures without melting, discoloring, offsetting, or releasing hazardous emissions. For detailed information, refer to the Card Stock & Label Guide, which is available on the Lexmark Web site at www.lexmark.com.
Transparencies can be fed automatically from the multipurpose feeder and all standard and optional trays, except the 2000-sheet drawer, for all printer models. See Print material specifications for information about transparency compatibility with output options.
Be careful when you handle transparencies. Fingerprints on the surface of the transparency cause poor print quality.

Properly storing the paper you buy helps ensure trouble-free printing. Use the following guidelines:

The following tables provide information on standard and optional paper sources, as well as output options, for your printer model, including the paper sizes you can select from the Paper Size menu and supported weights.
For information on card stock and labels, refer to the Card Stock & Label Guide located on the drivers CD.
400 UAT
T622
T620
A4 210 x 297 mm (8.27 x 11.7 in.)
See separate Finisher output support table.
A5 148 x 210 mm (5.83 x 8.27 in.)
JIS B5 182 x 257 mm (7.17 x 10.1 in.)
Letter 215.9 x 279.4 mm (8.5 x 11 in.)
Legal 215.9 x 355.6 mm (8.5 x 14 in.)
See separate Finisher output support table.
Executive 184.2 x 266.7 mm (7.25 x 10.5 in.)
Folio2 216 x 330 mm (8.5 x 13 in.)
Statement2 139.7 x 215.9 mm (5.5 x 8.5 in.)
1 This size setting formats the page for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application. 2 This size does not appear in the Paper Size menu until Tray Size Sensing is turned off. See Printing folio and statement size paper for more information.

400 UAT
T622
T620
Universal1 139.7 x 210 mm to 215.9 x 355.6 mm (5.5 x 8.27 in. to 8.5 x 14 in.)
See separate Finisher output support table. 69.85 x 127 mm to 229 x 355.6 mm (2.75 x 5 in. to 9.01 x 14 in.)
148 x 182 mm to 215.9 x 355.6 mm (5.83 x 7.17 in. to 8.5 x 14 in.)
7 ¾ Envelope 98.4 x 190.5 mm (3.875 x 7.5 in.)
See separate Finisher output support table.
9 Envelope 98.4 x 225.4 mm (3.875 x 8.9 in.)
10 Envelope 104.8 x 241.3 mm (4.12 x 9.5 in.)
DL Envelope 110 x 220 mm (4.33 x 8.66 in.)
C5 Envelope 162 x 229 mm (6.38 x 9.01 in.)
See separate Finisher output support table.
B5 Envelope 176 x 250 mm (6.93 x 9.84 in.)
Other Envelope1 98.4 x 162 mm to 176 x 250 mm (3.87 x 6.38 in. to 6.93 x 9.84 in.)
1 This size setting formats the page for 215.9 x 355.6 mm (8.5 x 14 in.) unless the size is specified by the software application. 2 This size does not appear in the Paper Size menu until Tray Size Sensing is turned off. See Printing folio and statement size paper for more information.

T620
Paper See separate Finisher output support table Card stock
Transparencies
Vinyl labels*
Paper labels*
Polyester labels*
Dual-web labels*
* Printing label applications on the T620 and T622 printers require a special label fuser cleaner which prevents duplexing. The label fuser cleaner is included with a special label cartridge for label applications. See Ordering supplies for more information on obtaining a label fuser cleaner.
Integrated tray and optional 500-sheet drawer
Multipurpose feeder and optional 250-sheet drawer Envelope feeder
Paper Xerographic or business paper
60 to 176 g/m2 grain long (16 to 47 lb bond)
60 to 135 g/m2 grain long (16 to 36 lb bond)
Card stock— maximum (grain long)1
Index Bristol 163 g/m2 (90 lb) 120 g/m2 (67 lb) Not recommended
Tag 163 g/m2 (100 lb) 120 g/m2 (74 lb) Not recommended
Cover 176 g/m2 (65 lb) 135 g/m2 (50 lb) Not recommended
1 Grain short is preferred for papers over 176 g/m2. 2 Printing label applications on your printer requires a special label fuser cleaner which prevents duplexing. 3 Information on whether your vinyl label converter has passed Lexmark's criteria is available at Lexmark’s Web site (www.lexmark.com); search for “converter list.” You can also check Lexmark’s Automated FAX system (LEXFAX™). 4 28 lb bond envelopes are limited to 25% cotton content. 5 Includes envelopes fed from the multipurpose tray only.

Integrated tray and optional 500-sheet drawer
Multipurpose feeder and optional 250-sheet drawer Envelope feeder
Index Bristol 199 g/m2 (110 lb) 163 g/m2 (90 lb) Not recommended
Card stock— maximum (grain short)1
Tag 203 g/m2 (125 lb) 163 g/m2 (100 lb) Not recommended
Cover 216 g/m2 (80 lb) 176 g/m2 (65 lb) Not recommended
Transparencies Laser printer 138 to 146 g/m2 (37 to 39 lb bond)
138 to 146 g/m2 (37 to 39 lb bond)
Labels—maximum2 Paper 180 g/m2 (48 lb bond)
163 g/m2 (43 lb bond)
Dual-web paper 180 g/m2 (48 lb bond)
163 g/m2 (43 lb bond)
Polyester 220 g/m2 (59 lb bond)
220 g/m2 (59 lb bond)
Vinyl3 300 g/m2 (92 lb liner)
260 g/m2 (78 lb liner)
140 to 175 g/m2 140 to 175 g/m2 Not recommended
Integrated forms Pressure- sensitive area (must enter the printer first)
75 to 135 g/m2
75 to 135 g/m2 (20 to 36 lb bond)
Paper base (grain long)
(20 to 36 lb bond)
Envelopes 100% cotton content maximum weight–24 lb
Sulfite, wood-free or up to 100% cotton bonds
Not recommended 60 to 105 g/m2
60 to 105 g/m2
(16 to 28 lb bond) 4, 5
(16 to 28 lb bond) 4
1 Grain short is preferred for papers over 176 g/m2. 2 Printing label applications on your printer requires a special label fuser cleaner which prevents duplexing. 3 Information on whether your vinyl label converter has passed Lexmark's criteria is available at Lexmark’s Web site (www.lexmark.com); search for “converter list.” You can also check Lexmark’s Automated FAX system (LEXFAX™). 4 28 lb bond envelopes are limited to 25% cotton content. 5 Includes envelopes fed from the multipurpose tray only.

Print material weight—output options
Print material Type 5-bin mailbox Output expander
High-capacity output stacker Finisher
Xerographic or business paper
60 to 90 g/m2
60 to 176 g/m2
60 to 176 g/m2
See separate Finisher media weight table
(16 to 24 lb bond)
(16 to 47 lb bond)
(16 to 47 lb bond)
Card stock— maximum (grain long)
Index Bristol Not recommended
163 g/m2 (90 lb)
Card stock— maximum (grain short)
Index Bristol Not recommended
See separate Finisher media weight table Dual-web paper
175 g/m2 175 g/m2
60 to 105 g/m2
60 to 105 g/m2
Envelopes Sulfite, wood-free or up to 100% cotton bond
(16 to 28 lb bond)
(16 to 28 lb bond)

Paper size Standard1 Offset Stapled
A4 210 x 297 mm (8.27 x 11.7 in.)
A5 148 x 210 mm (5.83 x 8.27 in.)
JIS B5 182 x 257 mm (7.17 x 10.1 in.)
Letter 215.9 x 279.4 mm (8.5 x 11 in.)
Legal 215.9 x 355.6 mm (8.5 x 14 in.)
Executive 184.2 x 266.7 mm (7.25 x 10.5 in.)
Folio2 216 x 330 mm (8.5 x 13 in.)
Statement2 139.7 x 215.9 mm (5.5 x 8.5 in.)
1 Paper passes to the output tray without being stapled or offset. 2 This size does not appear in the Paper Size menu until Tray Size Sensing is turned off. See Printing folio and statement size paper for more information.

Standard1 Offset Stapled
Paper Xerographic or business paper
60 to 176 g/m2
60 to 90 g/m2
60 to 90 g/m2
(16 to 47 lb bond)
(16 to 24 lb bond)
(16 to 24 lb bond)
Card stock— maximum (grain long)
Index Bristol 163 g/m2 (90 lb bond)
Not recommended Not recommended
Tag 163 g/m2 (100 lb bond)
Not recommended Not recommended
Cover Not recommended Not recommended Not recommended
Index Bristol 199 g/m2 (110 lb bond)
Card stock— maximum (grain short)
Not recommended Not recommended
Tag 203 g/m2 (125 lb bond)
Not recommended Not recommended
Cover 176 g/m2 (65 lb bond)
Not recommended Not recommended
Transparencies Laser printer 138 to 146 g/m2
37 to 39 lb bond) 138 to 146 g/m2
37 to 39 lb bond) Not recommended
Labels Not recommended Not recommended Not recommended
Integrated forms Not recommended Not recommended Not recommended
1 Paper passes to the output tray without being stapled or jogged.
Finisher media weight · Print material Type

This section provides information about loading the various input options. Proper paper loading helps prevent paper jams and ensure trouble-free printing.
Before loading paper, you need to know the recommended print side of the paper you’re using. This information is usually indicated on the paper package.
Click below for information on loading a particular option:


Complete these instructions to load print materials into any of the standard or optional trays.
1 Remove the paper tray.
2 Pull the width guide tab and slide the width guide to the far right side of the tray.
3 Squeeze the length guide lever and slide the length guide to the correct position for the size paper you are loading.

4 Place the paper into the paper tray with the recommended print side face down for single-sided printing and face up for double-sided printing. Do not fill paper above the paper capacity mark.
5 Pull the width guide tab and slide the width guide to the left until it lightly rests against the edge of the paper stack.

Length guide lever


6 Adjust the knob to show the size of the paper currently loaded.
Letterhead must be loaded differently depending on what options you have installed on your printer.
For simplex (single-sided) printing on letterhead, place the printed side face down as shown.


For duplex printing on letterhead, place the printed side face up as shown.

letterhead (or other preprinted media) that has been loaded specifically for duplex printing. See Paper Loading for more information.
For simplex (single-sided) printing on letterhead, place the printed side face down as shown.

For duplex printing on letterhead, place the printed side face up as shown.

letterhead (or other preprinted media) that has been loaded specifically for duplex printing. See Paper Loading for more information.

The multipurpose feeder can hold several sizes and types of paper, such as transparencies, postcards, note cards, and envelopes. It is useful for single page printing on letterhead, colored paper, or other special paper.
Keep in mind the following capacities, paper dimensions, and operating tips when loading the multipurpose feeder.
The maximum stack height is 10 mm (0.4 in.). The multipurpose feeder can hold approximately:
The multipurpose feeder accepts paper within the following dimensions:

The icons on the multipurpose feeder show you how to load the multipurpose feeder with paper, how to turn an envelope for printing, and how to load letterhead paper for simplex and duplex printing. If a finisher is installed, it will affect how letterhead documents are loaded for duplexing. See Loading letterhead for detailed instructions on loading documents printed on letterhead.

(single-sided) jobs on letterhead (or other preprinted media) that has been loaded specifically for duplex printing. For more information, see Paper Loading.
1 Push the lower release latch. The multipurpose feeder door drops open.


2 Locate the metal bar in the recessed area on the multipurpose feeder. Pull the bar out far enough to accommodate the paper you will be using.
3 Slide the paper width guide to the far right.
4 Prepare the print material for loading.
– Flex paper or fan envelopes back and forth. Do not fold or crease the paper. Straighten the edges on a level surface.


– Hold transparencies by the edges and avoid touching the print side. Fan the stack of transparencies to prevent jams. Be careful not to scratch or leave fingerprints on the transparencies.

5 Use the stack height limiter as a guide for stack height when loading print materials.
6 Load one type of print material in the multipurpose feeder. Do not mix types. Click a topic for loading instructions:


a Load paper with the left edge of the stack against the stack height limiter and with the recommended print side face up.
b Continue with step 7.

a Load envelopes flap side down with the stamp area and flap on the left. The end of the envelope with the stamp area enters the multipurpose feeder first.
self-stick adhesives. These envelopes may severely damage the printer.
multipurpose feeder.
b Continue with step 7.

Load letterhead according to the options installed on the printer. Click the topic that describes your printer configuration.

a Load letterhead paper for single-sided printing with the logo face up as shown.
a Load letterhead paper for duplex printing with the logo face down as shown.

b Continue with step 7.
(single-sided) jobs on letterhead (or other preprinted media) that has been loaded specifically for duplex printing. For more information, see Paper Loading.

a Load letterhead paper for single-sided printing with the logo face up as shown.
a Load letterhead paper for duplex printing with the logo face down as shown.
b Continue with step 7.
(single-sided) jobs on letterhead (or other preprinted media) that has been loaded specifically for duplex printing. For more information, see Paper Loading.


7 Gently slide the print material into the multipurpose feeder as far as it will go. Forcing the print material may cause it to buckle.
8 Slide the paper width guide to the left until it lightly touches the stack of print material. Do not bend the print material.
9 Select the paper source, size, and type from your software application and select paper size and type from the printer operator panel.
a Make sure the Paper Size and Paper Type for the multipurpose feeder (MP Feeder Size and MP Feeder Type) are set to the correct value for the print material you are loading. (See Paper Size and Paper Type for detailed information about these settings.)
b Press Go to return to Ready.


2 Push the metal bar straight back to collapse the multipurpose feeder to its short-length position.


1 Gently adjust the envelope support for the size you are loading:
– Fully closed (pushed in toward the printer) for short envelopes – Extended to the middle position for medium-length envelopes – Fully open (extended to its full length) for long envelopes

WARNING: Do not place objects on the envelope feeder. Avoid pressing down on it or applying
2 Lift the envelope weight back toward the printer. It stays in place.


3 Slide the envelope edge guide to the far right.
4 Flex a stack of envelopes back and forth and then straighten the edges on a level surface. Press down the corners to flatten them.

Fan the envelopes. This prevents the edges of the envelopes from sticking together and helps them feed properly.
(2.55 in.). The envelope feeder holds a maximum of 85 envelopes (75 g/m2, 20 lb bond).

5 Load the stack of envelopes flap side down with the stamp area and the flap on the left. The end of the envelopes with the stamp area enters the envelope feeder first. Let the envelopes at the bottom of the stack slide into the envelope feeder slightly more than the ones at the top of the stack.

self-stick adhesives. These envelopes may severely damage the printer. See Choosing envelopes for more information.

6 Slide the envelope edge guide to the left until it lightly touches the stack. Make sure the envelopes do not buckle.
7 Lower the envelope weight to the stack.


8 Select the paper source, size, and type from your software application.
9 Select the paper size and type from printer operator panel:
a Make sure the Paper Size for the envelope feeder (Env Feeder Size) is set to the correct envelope size you are loading. (See Paper Size for detailed information about this setting.)
b Press Go to return to Ready.
If envelopes jam, see Clearing paper jams.

For information on loading the optional 2000-sheet drawer, refer to the 2000-Sheet Drawer User’s Guide on the Lexmark PRODUCT Publications CD that came with your printer.

Tray linking enables the automatic linking feature for trays when you use the same size and type of print material in multiple paper sources (trays).
For example, let’s say you have loaded two optional trays with the same size print material and both are set to the same paper type. When one tray becomes empty, the printer automatically selects print material from the other tray since the printer sees the trays as linked.
If you use different print material in the trays, each source with a different print material must have the Paper Type set to a unique value to disable the automatic linking feature. If all the trays do not have the same paper type when they are linked, you could mistakenly print a job on the wrong paper type.

By carefully selecting print materials and loading them properly, you should be able to avoid most paper jams. If jams do occur, follow the steps outlined in Clearing paper jams. If jams occur frequently, make sure you follow these tips to avoid jams:

Order a new print cartridge when the Toner Low message first appears so you will have it when the current one no longer prints satisfactorily. See Ordering supplies for information on ordering print cartridges.
quality and printer reliability cannot be guaranteed if you do. For best results, use Lexmark supplies.
Complete the following steps to replace the print cartridge. Refer to the documentation that comes with the print cartridge for detailed installation information.
1 Turn the printer off and unplug the printer power cord.
2 Open the front doors and remove the used print cartridge.
the handhold on the cartridge to avoid touching this area.
3 Clean the printer.
4 Install the new print cartridge and close the front door.
5 Replace the fuser cleaner if you are printing special label applications.
6 Plug the printer power cord into a properly grounded electrical outlet and turn the printer on.
7 Follow the instructions on the new print cartridge box to return the used print cartridge to Lexmark for recycling.
When you return a used print cartridge, you contribute to a worldwide recycling effort at no cost to you.

Order a new charge roll kit when toner fog or background shading appears on printed pages. See Ordering supplies for information on ordering a charge roll.
Complete the following steps to replace the charge roll. Refer to the documentation that comes with the charge roll for detailed installation information.
1 Turn the printer off and unplug the printer power cord.
2 Open the front doors and remove the print cartridge.
3 Remove the old charge roll.
4 Install the new charge roll.
5 Reinstall the print cartridge and close the front doors.
6 Plug the printer power cord into a properly grounded electrical outlet.
7 Reset the maintenance counter.

Order a new transfer roll when light print, toner fog, or background shading appears on printed pages. See Ordering supplies for information on ordering a transfer roll.
Complete the following steps to replace the transfer roll. Refer to the documentation that comes with the transfer roll for detailed installation information.
1 Turn the printer off and unplug the printer power cord.
2 Open the front doors and remove the print cartridge.
3 Remove the old transfer roll.
4 Install the new transfer roll.
5 Reinstall the print cartridge and close the front doors.
6 Plug the printer power cord into a properly grounded electrical outlet.
7 Reset the maintenance counter.

Order a new fuser assembly when toner fog or background shading appears on printed pages. See Ordering supplies for information on ordering a fuser assembly.
Complete the following steps to replace the fuser assembly. Refer to the documentation that comes with the fuser assembly for detailed installation information.
changing the fuser assembly.
1 Turn the printer off, unplug the printer power cord, and wait twenty minutes.
2 Remove the top cover and all installed output options. If a duplex unit is installed, remove it.
3 Remove the fuser cover.
4 Lift up and remove the fuser cleaner.
5 Open the rear access door and remove the redrive.
6 Remove the old fuser assembly.
Canada, call 1-800-438-2468 for information about Lexmark Authorized Supplies Dealers in your area. In other countries, contact the place where you bought your printer.
7 Install the new fuser assembly and replace the redrive.
8 Close the rear access door and replace the fuser cover.
9 If you have a duplex unit, reinstall it. Reinstall all output options and the printer top cover.
10 Plug the printer power cord into a properly grounded electrical outlet.
11 Reset the maintenance counter.

When Staples Low or Staples Empty appears on the operator panel display, complete the steps to insert a new staple cartridge in the finisher. Refer to the illustrations inside the stapler access door for more information. For information about ordering staple cartridges, see Ordering supplies.
Staples message. Install a new staple cartridge or press Go to clear the message and continue printing. If Staple Alarm is set to Continuous, the printer displays the Load Staples message and continues printing.
1 Open the stapler access door and remove the staple cartridge holder by pulling on the colored tab.
message appears. Do not remove this sheet. Install a new staple cartridge to properly feed the partial sheet of staples.
2 Remove the empty staple cartridge.
3 Install the new staple cartridge.
4 Reinstall the staple cartridge holder and close the stapler access door.
Priming Stapler appears on the display. Priming occurs automatically without creating any output, and ensures the stapler is functioning properly.

After replacing all the items in the maintenance kit, reset the maintenance counter:
1 Press and hold the Select and Return buttons while you turn the printer on.
2 Release the buttons when Performing Self Test appears on the display.
The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.
3 Press Menu until you see Reset Maint Cnt and then press Select.
Reset appears on the second line of the display.
4 Press Select.
Resetting Maint Cnt Value appears briefly on the display, and then is replaced by Config Menu on the top line and Reset Maint Cnt on the second line.
5 Press Menu until you see Exit Config Menu, and then press Select.
Activating Menu Changes appears briefly, followed by Performing Self Test. The printer returns to the Ready state.



For best results, use Lexmark supplies with the printer. If you are in the U.S. or Canada, call 1-800-438-2468 for information about Lexmark Authorized Supplies Dealers in your area, or visit the Lexmark Web site at www.lexmark.com In other countries, contact the place where you bought your printer.
80 Scheduled Maintenance appears on the display after 300,000 pages have printed to let you know it is time to replace printer maintenance items. Order a maintenance kit when 80 Scheduled Maintenance first appears on the display. The maintenance kit contains all the items necessary to replace the fuser assembly, the charge roll, and the transfer roll. See the following table for the maintenance kit part number for your specific printer.
Maintenance kit for T622(n) 220 V, 875 W 99A2410
Maintenance kit for T622(n) 115 V, 875 W 99A2411
Maintenance kit for T620(n) 220 V, 875 W 11K2407
Maintenance kit for T620(n) 115 V, 875 W 11K2408
For finisher maintenance information, refer to the StapleSmart Reference that came with your finisher.
Order a new print cartridge when Toner Low first appears on the display so you will have it when the current one no longer prints satisfactorily.
Description Part number

Three Prebate™ print cartridges and two regular priced print cartridges are specifically designed for your printer:
Prebate print cartridge part number1 Average yield
5% 12A6865 30,000 pages
12A6869 (Label Cartridge; shipped with a Label Fuser Cleaner2)
1 Sold at a special price with the understanding that you return your empty cartridges only to Lexmark. For regular priced cartridges without these terms, order part number 12A6760 (10,000 pages) or 12A6765 (30,000 pages).
2 Label fuser cleaners are not recommended for duplex printing.
A special label fuser cleaner should be used for label applications to optimize feeding reliability. They are included in the print cartridge box when you order part number 12A6869. You also may order this item separately using part number 99A0725.
Label fuser cleaners are not recommended for duplex printing.
Order part number 99A1017.
Order part number 99A1015.
Staple cartridges hold 3,000 staples. Use part number 11K3188 to order a pack of three staple cartridges.
Print coverage (approximate) · 12A6860 10,000 pages · 30,000 pages

Order a fuser assembly when 80 Scheduled Maintenance first appears on the display. See the following table for the fuser assembly part number for your specific printer.
Fuser assembly for T622(n) 115 V, 875 W 99A2405
Fuser assembly for T622(n) 220 V, 875 W 99A2404
Fuser assembly for T620(n) 115 V, 875 W 99A2402
Fuser assembly for T620(n) 220 V, 875 W 99A2401
Description Part number

Store supplies in their original packaging until you are ready to install them.
Do not store supplies in:

When you have a problem, first make sure that:


By carefully selecting print materials and loading them properly, you should be able to avoid most paper jams. (See the suggestions in Tips for avoiding paper jams.) If paper jams do occur, follow the steps outlined in this section.
To resolve the paper jam messages, you must clear all paper from the paper path. Press Go to resume printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto; however, the Auto setting does not guarantee the page will print.
See the diagram on page 68 for the path the paper travels through the printer and options, and areas where jams may occur. The path varies depending on the paper source and output bin.


You open doors and covers, remove paper trays, and remove options to access paper jam areas. If your printer has a multipurpose feeder, it is visible when the lower front door is opened. The illustration shows the location of paper sources and possible paper jam areas.

5-bin mailbox, rear door Output expander, rear door (High-capacity output stacker and finisher not shown)
Lower front door (down when envelope feeder is installed)

A 200 Paper Jam message indicates the paper is jammed in the area under the print cartridge. This requires removing the print cartridge from the printer. A 201 Paper Jam message indicates the jam is farther inside the printer.
1 Push the release latch and open the printer upper and lower front doors.
2 While grasping the print cartridge by the hand grip, pull the print cartridge up toward the upper front door, and then pull it straight out toward you.
the handhold on the cartridge to avoid touching this area.
Lay the print cartridge aside.
3 Gently push the feed roller release lever toward the back of the printer.


4 Pull the paper up and toward you.
If the paper does not move immediately when you pull, stop pulling. You need to access the paper from the rear door. See Between the envelope feeder and the printer for more information.

5 Reinstall the print cartridge.
6 Close the upper and lower front doors.
Jams that cause a 202 Paper Jam message require opening the printer rear door.
For instructions on clearing the jam, click the area where the jam occurred:

1 Open the rear door.
2 Remove the paper based on what part is visible.
– If the middle section of paper is visible, grasp it on both sides and gently pull it straight out.

– If paper is still in the fuser area, open the upper front door and remove the paper. – If the end of the paper is visible, pull the paper straight out.

If the paper does not move immediately when you pull, stop pulling. Remove the print cartridge, and then pull the paper out.
3 Close the rear door.

Pull the paper straight out.

If the paper does not move immediately when you pull, stop pulling. Open the upper front door and pull the paper out.


Jams that cause a 230 Paper Jam message require opening the duplex front access cover.

1 Open the duplex rear door.
2 Look under the duplex rear door for the edge of the paper to determine how the paper is jammed:
– If a short piece is visible inside the duplex unit next to the inner wall, grasp it and pull it out. If you cannot grasp it, see step 6. – If only a short piece of paper is visible toward the rear of the printer, do not pull it out; it may be easier to access from inside the printer. See 200 and 201 Paper Jam Remove Cartridge for instructions. – If most of the paper is visible, continue with the following.

3 Pull the paper up and out toward you if the paper is in this position:


4 Pull down and out if the paper is in this position:
5 Close the duplex rear door. Make sure it snaps into place.
6 Locate the recessed areas on each side of the duplex front access cover.
7 Slowly pull the duplex front access cover straight out.


8 If the edge of the paper is visible, pull the paper straight up and out.

If the paper is not visible, continue with step 9. Otherwise, close the duplex front access cover.
9 Slide out the integrated tray.
10 Remove any sheets of paper lying in the duplex front access cover.
Interior view of duplex unit

11 Slide the duplex front access cover back into the duplex unit. Make sure it snaps into place.
12 Slide the integrated tray back into the printer.

Jams in four areas result in a 24x Paper Jam message, where x represents the tray number where the jam has occurred.
For instructions on clearing the jam, click the area where the jam occurred:
1 Pull the paper tray halfway out of the support unit.
2 Remove the paper based on how it is jammed:
– If the paper is lying on the incline or wall surface at the front of the tray, pull the paper straight out.
– If the paper is in the pass-through area between two trays, pull the paper straight up and out.

– If you do not see either end of the print material, see Between three trays to remove the jam.
3 Slide the paper tray back into the support unit.
This type of jam may occur if you are using legal-size paper in the trays or if you have a 250-sheet drawer installed with other optional drawers.
1 Pull the paper tray out of the support unit. If only a short piece of the paper is visible, do not pull down to remove the paper.

2 Gently slide the paper tray back into the support unit.
3 Pull the paper tray out of the support unit that is above the tray you just closed.
4 Pull the paper either up or down. If it does not pull easily one way, try the other way.

5 Slide the paper tray back into the support unit.
the print cartridge and any jammed paper, and then reinstall the print cartridge.


1 Pull the paper tray out of the support unit. If only a short piece of the paper is visible, do not pull down to remove the paper.
2 Slowly pull the duplex front access cover straight out from the duplex unit.


3 Pull the integrated tray out of the printer.
If you see the edge of the paper in the integrated tray:
a Pull the paper down and out.

b Slide the tray all the way into the printer.
c Slide the duplex front access cover back into the duplex unit. Make sure it snaps into place.
If you do not see the edge of the paper in the integrated tray:
a Push the tray back into the printer.
b Open the printer upper and lower front doors.
c Remove the print cartridge.
the handhold on the cartridge to avoid touching this area.
You should see the leading edge of the paper now.

d Gently push the feed roller release lever toward the back of the printer.

e Pull the paper out.

f Reinstall the print cartridge. Align the slides on the print cartridge with the slots on the print cartridge cradle. Use the colored arrows inside the printer for placement. Guide the print cartridge down as it snaps into place.
g Close the printer upper and lower front doors.
h Slide the paper tray all the way into the printer.


1 Open the loading door.
2 Press the elevator down button.
3 Remove the paper jam. Clear all paper from the paper path of the drawer and printer.
4 Make sure the stack of paper is neat and aligned; otherwise, another paper jam may occur.
5 Close the door.
6 Allow a few seconds for the elevator to reach the top.
7 Press Go to resume printing.

Slowly pull the jammed print material straight out of the multipurpose feeder.
Elevator down button

Envelope jams may occur in two areas.
For instructions on clearing the jam, click the area where the jam occurred:
Since the envelope feeder feeds envelopes from the bottom of the stack, the envelope on the bottom is jammed.
1 Lift the envelope weight.
2 Flip the envelope weight back toward the printer.

3 Remove the stack of envelopes from the envelope feeder.
4 Slowly pull the jammed envelope straight out toward you.
5 Replace the stack of envelopes in the envelope feeder.
6 Adjust the envelope edge guide.
7 Lower the envelope weight to the stack.
between steps 4 and 5. This may correct the problem.

1 Lift the envelope weight.

2 Flip the envelope weight back toward the printer.
3 Remove the stack of envelopes from the envelope feeder.
4 Push the envelope support to the closed position.
6 Pull the envelope feeder up slightly and straight out of the printer. Set it aside.

7 Pull the envelope straight out of the printer.

8 Reinstall the envelope feeder. Make sure it snaps into place.
9 Close the printer upper front door.
10 Replace the stack of envelopes in the envelope feeder.
11 Adjust the envelope edge guide.
12 Lower the envelope weight to the stack.
Jams in two areas result in a 27x Paper Jam message, where x represents the bin number where the jam has occurred.
Paper jams in output options (output expander, high-capacity output stacker, or 5-bin mailbox) may be:
Paper jams as it exits to an output option bin and:

1 Pull the paper straight out. If the paper does not give immediately when you pull, stop pulling. Continue with the next step.

2 Push the output option rear door latches in toward the center. The rear door opens and drops down.

3 Loosen the paper if it is caught in the feeder rollers, and then pull the paper straight out.
4 Close all output option rear doors.
Try to pull the paper from the front of the bin. If you are not successful, complete the following steps.
1 Push the output option rear door latches in toward the center. The rear door opens and drops down.
2 Repeat for the output option installed above the option where the jammed has occurred.

3 Pull the paper straight out from the output option.
4 Close all output option rear doors. Make sure all rear door latches are closed.
1 Push the output option rear door latches in toward the center. The rear door opens and drops down.
2 Repeat for the output option installed above the option where the jam has occurred.
both of its rear doors.

3 Pull the paper straight out from the output option.
4 Close all output option rear doors. Make sure all rear door latches are closed.
Jams in the optional finisher may result in a 28x Paper Jam message, where x represents specific jam areas. The second line of the operator panel indicates the jam area.
Possible 28x Paper Jam messages include:
1 Push the finisher rear door latches in toward the center. The rear door opens and drops down.

2 Pull the paper straight out from the finisher.
3 Close the rear door. Make sure the latches are closed.
1 Lift the front edge of the finisher output bin cover until it locks into vertical position.



Jams in the optional finisher may result in a 28x Staple Jam message, where x represents specific jam areas. The second line of the operator panel indicates the jam area.
Possible 28x Staple Jam messages include:
1 Lift the front edge of the finisher output bin cover until it locks into vertical position.


3 Continue with step 1 on page 92.
1 Press the latch to open the stapler access door.

2 Firmly pull the colored tab to remove the staple cartridge holder from the stapler.
3 Turn the cartridge holder as shown in the illustration in step 4.

4 Use the metal tab to lift the staple guard, and then pull out the sheet of staples.
Discard the entire sheet.

5 Remove any loose staples attached to the inside of the staple guard.
6 Look through the clear covering on the bottom of the cartridge holder to make sure no staples are jammed in the entry throat.
7 Press down on the staple guard until it snaps securely into place.

8 Push the cartridge holder firmly into the stapler until the cartridge holder clicks into place.
Priming Stapler appears on the operator panel display. Priming occurs automatically to ensure the stapler is functioning properly.
10 Close the finisher output bin cover.
staple guard

If the suggested corrective action does not fix the problem, call your service representative.
Operator panel displays only diamonds or is blank.
If the messages do not appear, turn the printer off and call the Lexmark Customer Support Center.
Menu settings changed from the operator panel have no effect.
Settings in the software application, the printer driver, or the printer utilities are overriding the settings made from the operator panel.
Problem Action

If the suggested corrective action does not fix the problem, call your service representative.
Job did not print or incorrect characters printed.
Make sure Ready appears on the operator panel before you send a job to print. Press Go to return to Ready.
Make sure there is print material loaded in the printer. Press Go to return to Ready.
Verify that the printer is using the correct printer language.
Verify that you are using the correct printer driver.
Make sure the parallel, serial, ethernet, or USB cable is firmly plugged in at the back of the printer. Make sure you are using the correct cable. Use IEEE 1284-compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft). If you use RS-232 Serial, verify that a null modem cable is used.
If the printer is connected through a switch box, try a direct connection.
Verify that the correct paper size is selected through the operator panel, in the printer driver, or in the software application.
Make sure PCL SmartSwitch and PS SmartSwitch are set to On.
Job did not print or incorrect characters printed (continued).
If you are using a print spooler, verify that the spooler is not stalled.
If you print across a network or on a Macintosh computer, see Network printing problems.
Check the printer interface from the Setup Menu.
Determine which host interface you are using. Print a menu settings page to verify that the current interface settings are correct. See Printing the menu settings page.
If you are using a serial interface:
Printer is connected to the USB port, but will not print.
Make sure you are using Windows 98, Windows 2000, Windows Me, or another USB-capable operating system supported by Lexmark.
Print material misfeeds or multiple feeds occur.
Make sure the print material you are using meets the specifications for your printer. See Print material specifications for more details.
Flex print material before loading it in any of the paper sources.
Make sure the print material is loaded correctly.
Problem Action

Print material misfeeds or multiple feeds occur (continued).
Make sure the paper width and length guides on the paper sources are adjusted correctly.
Do not overfill the paper sources.
Do not force print material into the multipurpose feeder when you load it; otherwise, it may skew or buckle.
Remove any curled print material from paper sources.
Load the recommended print side correctly for the type of print material you are using. See Loading print material for more information.
Load less print material in the paper sources.
Turn the print material over or around and try printing again to see if feeding improves.
Do not mix print material types.
Do not mix reams of print material.
Remove the top and bottom sheets of a ream before loading the print material.
Load a paper source only when it is empty.
Envelope misfeeds or multiple feeds occur.
Remove the stack of envelopes from the envelope feeder. Load one envelope, feed it through the printer, and then reload the stack of envelopes in the envelope feeder.
Page breaks in unexpected places.
Check the Print Timeout setting in the Setup Menu. Increase the setting.
Job prints from the wrong paper source or on the wrong print material.
Check the Paper Type setting in the Paper Menu from the printer operator panel and in the printer driver.
Paper does not stack neatly in any output bin.
Problem Action

If the suggested corrective action does not fix the problem, call your service representative.
Toner smears or print comes off the page.
Toner appears on the back of the printed page.
Toner is on the transfer roll. To help prevent this, do not load print material that is smaller than the page size of the job to be printed.
Open and close the printer upper front door to run the printer setup cycle and clean the transfer roll.
Problem Action

Toner fog or background shading appears on the page.
Printing is too dark. Change the Toner Darkness setting in the Quality Menu.
Problem Action

Characters have jagged or uneven edges.
Part or all of the page is printed in black.
The job prints, but the top and side margins are incorrect.
Problem Action

If an option does not operate correctly after it is installed or if it quits working:
For Macintosh computer users: Make sure the printer is set up in Chooser.
The following table lists printer options and suggested corrective actions for related problems. If the suggested corrective action does not fix the problem, call your service representative.
5-bin mailbox Make sure the connection between each 5-bin mailbox or the connection between the 5-bin mailbox and the printer is secure. If the 5-bin mailbox is listed on the menu settings page, but print material jams when it exits the printer and enters the mailbox, it may not be properly installed. Reinstall each 5-bin mailbox.
Flash memory Make sure flash memory is securely connected to the printer system board.
Hard disk with adapter
Make sure the hard disk is securely connected to the hard disk adapter card. Also make sure the hard disk adapter card is securely connected to the printer system board.
Option Action

Make sure the connection between the output stacker and the printer is secure. If the high-capacity output stacker is listed on the menu settings page, but print material jams when it exits the printer and enters the output stacker, it may not be properly installed. Reinstall the high-capacity output stacker.
Infrared adapter If infrared communication stops or does not occur, make sure:
Refer to the drivers CD for more details.
Output expander Make sure the connection between each output expander or the connection between the output expander and the printer is secure. If the output expander is listed on the menu settings page, but print material jams when it exits the printer and enters the output expander, it may not be properly installed. Reinstall each output expander.
Printer memory Check to make sure printer memory is securely connected to the printer system board.
Tri-Port Adapter Make sure the Tri-Port Adapter is securely connected to the printer system board.
For Macintosh computer users, make sure the host computer is set to LocalTalk.
If you are using a phone wire connection, use a terminator plug.
Make sure you are using the correct cable and that it is securely connected.

If a job did not print or incorrect characters printed, verify that the Lexmark internal print server or external print server is set up properly and the network cable is connected.
For Novell users:
For Macintosh users:

I need to get updated printer drivers or utilities.
I need to attach a serial cable to the printer.
If your printer is configured with a serial port, or you have installed an optional interface card, refer to the Setup Guide.
I can’t find the printer escape codes.
Refer to the Technical Reference available on the Lexmark Web site at www.lexmark.com
Problem Action

The printer operator panel displays messages describing the current state of the printer and indicates possible printer problems you must resolve. This topic provides a list of all printer messages, explains what they mean, and tells you how to clear the messages.
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
Click a letter or number at the bottom of the page to locate information about a message beginning with that character.
Light

The printer is activating changes made to the printer settings.
Wait for the message to clear.
The specified bin is full.
Remove the stack of paper from the bin to clear the message. If you assigned the bin a name, the bin name is displayed instead of the bin number.
The printer is busy receiving, processing, or printing data.
Canceling Job
What this message means:
The printer is processing a request to cancel the current print job.
Wait for the message to clear.
Cancel Job

The printer is requesting different paper than what is loaded in the specified tray or defined by the Paper Size or Paper Type settings for that tray.
The specified device is either not fully connected to the printer or is experiencing a hardware failure.
The printer detects a paper jam, and you must remove the stack of paper in the finisher as well as clear the jam.
Jam message.
Clear paper from the entire paper path. Press Go to clear the message and continue printing.

The printer is deleting all job statistics stored on the hard disk.
Wait for the message to clear.
The upper front door is open or the print cartridge is not installed.
The printer is defragmenting the flash memory to reclaim storage space occupied by deleted resources.
Wait for the message to clear. No button actions are possible while this message is displayed.
WARNING: Do not turn the printer off while this message is displayed.
The printer is requesting confirmation to delete all held jobs.

The printer is deleting one or more held jobs.
Wait for the message to clear.
The printer is responding to a request to disable the menus.
Wait for the message to clear.
operator panel.
Disabling operator panel menus
The printer has attempted a disk recovery process and cannot repair the disk. The disk cannot be used unless it is reformatted.
Disk Recovery x/5 yyy%

The printer is attempting to recover the hard disk after finding errors on it. The disk recovery takes place in five phases. The second line on the operator panel shows the percent complete of the current phase.
The printer is responding to a request to make the menus available to all users.
Wait for the message to clear and then press Menu to view the menus from the operator panel.
Disabling operator panel menus
Someone has changed the Energy Conserve setting in the Config Menu. This setting determines the values available for the Power Saver menu item.
Power Saver; Disabling Power Saver;Technical Reference

The printer is waiting for you to enter your four-digit personal identification number (PIN).
Use the operator panel buttons to enter the PIN you identified in the driver when you sent the confidential job to the printer.
Flushing Buffer
What this message means:
The printer is flushing corrupted print data and discarding the current print job.
Wait for the message to clear.
The printer is formatting the hard disk. Since formatting the disk may take longer in some cases, the second line may show the percent complete.
Wait for the message to clear.
WARNING: Do not turn the printer off while this message is displayed.
The printer is formatting the flash memory.
Confidential jobs

Wait for the message to clear.
WARNING: Do not turn the printer off while this message is displayed.
Held Jobs may be lost.
The printer memory is too full to continue processing print jobs.
– Delete fonts, macros, and other data stored in printer memory. – Install more printer memory.
alternate on the display.
An infrared interface is the active communication link.
The stapler is either not installed or not installed correctly.
cartridge holder were installed but out of staples. If the Load Staples message appears, press Go again to ignore the message and print the job without stapling it.

Insert Tray <x>
What this message means:
The specified tray is either missing or not fully inserted.
Insert the specified tray completely.
The printer is requesting that a specified device be installed so it can print a job.
Invalid Network <x> Code
Invalid Standard Network Code
What this message means:
The code in an internal print server is not valid. The printer cannot receive and process jobs until valid code is programmed into the internal print server.
Download valid code to the printer internal print server. No button actions are possible while this message is displayed.
Setup Guide · Setup Guide · Technical Reference

The printer detects a paper jam while printing a job that must be stapled.
Clear paper from the entire paper path, but leave the job waiting to be stapled in the finisher. Press Go to clear the message and continue printing.
Load Manual
What this message means:
A request for a manual feed job has been sent to the printer. The printer is ready for insertion of a single sheet into the manual feed slot.
Loading the multipurpose feeder
The printer is trying to staple a print job, but the stapler is empty.
Clearing paper jams

Replacing the staple cartridge
The printer is trying to feed paper from a source it detects is empty.
A LocalTalk interface is the active communication link.
The printer requires replacement of routine maintenance items to maintain top performance and to avoid print quality and paper feed problems.
Replace the maintenance items and reset the printer maintenance counter (if necessary).
The printer menus are disabled. You cannot change the printer settings from the operator panel.

You can still open the Job Menu to cancel a job that is printing or to select a confidential job or a held job that you want to print. If you need access to the printer menus, contact your network administrator.
An internal print server (also called an internal network adapter or INA) is being reset.
Wait for the message to clear.
A network interface is the active communication link.
A network interface is the active communication link, where represents the active communication link and represents the channel.
The four-digit personal identification number (PIN) you entered is not associated with any confidential print job.

The printer is not ready to receive or process data. Someone pressed Stop to take the printer offline.
Press Go to make the printer ready to receive jobs.
The printer designated overflow bin is full.
Remove the stack of paper from the bin to clear the message.
A parallel interface is the active communication link.
The printer is running the series of start-up tests it performs after it is turned on.
Wait for the message to clear.
The printer is ready to receive and process data. It is reducing its electricity consumption while idle. If the printer remains inactive for the period of time specified in the Power Saver menu item (factory default settings are 30 minutes on the T620 and 60 minutes on the T622), the Power Saver message replaces the Ready message.

Power Saver (Setup Menu)
The printer failed to prepare the stapler to staple print jobs.
The printer is preparing the stapler to staple print jobs. The printer tests the stapler several times before returning to the Ready state.
Wait for the message to clear.
Jobs that were spooled to the hard disk before the printer was last turned off have not yet printed.

The printer is processing or printing a directory of all files stored in flash memory or on a hard disk.
Wait for the message to clear.
The printer is processing or printing a list of all available fonts for the specified printer language.
Wait for the message to clear.
The printer is processing or printing all job accounting statistics stored on the hard disk.
Wait for the message to clear.
The printer is processing or printing the menu settings page.

Wait for the message to clear.
The printer is programming new code into the flash memory.
Wait for the message to clear.
WARNING: Do not turn the printer off while this message is displayed.
The printer is programming new system code.
Wait for the message to clear and the printer to reset.
WARNING: Do not turn the printer off while this message is displayed.
The printer is storing resources, such as fonts or macros, in flash memory.
Wait for the message to clear.
WARNING: Do not turn the printer off while this message is displayed.
The printer is storing resources, such as fonts or macros, on the hard disk.

Wait for the message to clear.
WARNING: Do not turn the printer off while this message is displayed.
The printer is deleting one or more held jobs and sending one or more jobs to print.
Wait for the message to clear.
The printer is sending one or more held jobs to print.
Wait for the message to clear.
The printer is ready to receive and process print jobs.
Send a job to print.
The printer is in Hex Trace mode and is ready to receive and process print jobs.

The specified device is either not fully connected to the printer or is experiencing a hardware failure.
The specified output bin, or bins, is full.
Remove the stack of paper from the specified bin(s) to clear the message.
The printer is reducing the resolution of a page in the current job from 600 dots per inch (dpi) to 300 dpi to prevent a 38 Memory Full error. Res Reduced remains on the display while the job prints.
Press Menu to open the Job Menu and cancel the current job.

The printer is resetting to the active bin in a linked set of bins.
Wait for the message to clear.
The printer is resetting to the current default settings. Any active print jobs are canceled.
Wait for the message to clear.
The printer is resetting the counter that tracks wear on the fuser.
Wait for the message to clear.
The printer detects Print and Hold jobs stored on the hard disk during a power-on cycle or a printer reset.

The printer is restoring the factory default printer settings. When factory default settings are restored:
– The Display Language setting in the Setup Menu. – All settings in the Parallel Menu, Serial Menu, Network Menu, Infrared Menu, LocalTalk Menu, USB Menu, and Fax Menu.
Wait for the message to clear.
The printer is restoring held jobs from the hard disk.
Wait for the message to clear. No button actions are possible while this message is displayed.
A serial interface is the active communication link.
The stapler is out of staples, or the stapler is not installed.
If necessary, install a new staple cartridge. Reinsert the stapler to clear the message.
message appears. Do not remove this sheet. Install a new staple cartridge to properly feed the partial sheet of staples.

Replacing the staple cartridge
The stapler has only a few staples remaining.
Install a new staple cartridge to clear the message.
message appears. Do not remove this sheet. Install a new staple cartridge to properly feed the partial sheet of staples.
Replacing the staple cartridge
The standard output bin is full.
Remove the stack of paper in the bin to clear the message.
The print cartridge is low on toner.

Replacing the print cartridge
The specified tray is out of paper.
Load paper in the tray to clear the message.
The specified tray is low on paper.
Add paper to the tray to clear the message.
The specified tray is either missing or not fully inserted into the printer.
Insert the tray completely into the printer.
The printer is processing data through the specified USB port.
The printer has received a page of data to print but is waiting for an End of Job command, a Form Feed command, or additional data.

The printer detects a paper jam. Although the location of the paper jam appears on the second line of the display, you must clear paper from the entire paper path.
Clear the paper path.
31 Defective Print Cartridge
What this message means:
A defective print cartridge is installed.
Remove the print cartridge and install a new one.
An unsupported print cartridge is installed.
Remove the print cartridge and install a supported one.
Replacing the print cartridge
Clearing paper jams

The printer has determined that the length of the paper in the source specified on the second line of the display is too short to print the formatted data. For auto-size sensing trays, this error occurs if the paper guides are not in the correct position.
The printer lacks the memory needed to enable Resource Save. This message usually indicates too much memory is allocated for one or more of the printer link buffers.
– Make sure the link buffers are set to Auto, and exit the menus to activate the link buffer changes. – When Ready is displayed, enable Resource Save from the Setup Menu.
The printer memory (or hard disk, if installed) does not have the free space necessary to collate the print job.

The printer cannot defragment flash memory, because the printer memory used to store undeleted flash resources is full.
The printer memory is full and cannot continue processing current print jobs.
– Delete fonts, macros, and other data in printer memory. – Install additional printer memory.
alternate on the display.
The printer is processing data, but the memory used to store pages is full.

– Simplify the print job by reducing the amount of text or graphics on a page and deleting unnecessary downloaded fonts or macros. – Install additional printer memory.
The page may not print correctly because the print information on the page is too complex.
– Reduce the complexity of the page by reducing the amount of text or graphics on the page and deleting unnecessary downloaded fonts or macros. – Set Page Protect to On in the Setup Menu. – Install additional printer memory.
The printer detects defective flash memory.
Press Go to clear the message and continue printing. You must install different flash memory before you can download any resources to flash.
There is not enough free space in the flash memory to store the data you are trying to download.

The printer detects unformatted flash memory.
54 Standard Serial Error
The printer has detected a serial interface error on a serial port.
54 Std Network Software Error
The printer cannot establish communications with an installed network port.
54 Par <x> ENA Connection Lost

The printer has lost the connection to an external print server (also called an external network adapter or ENA).
The printer has detected a protocol error on a parallel interface.
The buffer used to process data is too full to receive an incoming fax. This has broken the connection between the printer and the sending fax machine. The printer will not accept additional fax data until sufficient fax buffer space is made available.
56 Standard Serial Disabled
Data has been sent to the printer through a serial port, but the serial port is disabled.

56 Std Parallel Port Disabled
Data has been sent to the printer through a parallel port, but the parallel port is disabled.
Turn off and unplug the printer. Remove or reconfigure the output bins. Plug in the printer and turn it on.
Too many hard disks are installed on the printer. The printer only supports one hard disk at a time.
Turn off and unplug the printer. Remove the excess hard disks from the printer. Plug in the printer and turn it on.

Too many flash memory options are installed on the printer.
Turn off and unplug the printer. Remove the excess flash memory. Plug in the printer and turn it on.
Too many drawers with matching trays are installed on the printer.
Turn off and unplug the printer. Remove the additional drawers. Plug in the printer and turn it on.
The printer detects that an incompatible device is installed.
Remove the specified device.
The printer detects a defective hard disk.

There is not enough memory on the hard disk to store the data sent to the printer.
The printer detects an unformatted hard disk.
Messages labeled 70–79 identify problems related to the internal print server.
Refer to the drivers CD for more information. Click View Documentation, and then click MarkNet™ Print Servers.
The printer requires replacement of routine maintenance items to maintain top performance and avoid print quality and paper feed problems.

Replace the maintenance items and reset the printer maintenance counter, if necessary.
Microcode in the engine flash code module has failed a system check.
Press Go to clear the message and discard the code. Retransmit the microcode data from the host computer.
The print cartridge is low on toner.
Replacing the print cartridge
Messages labeled 900–999 relate to printer problems that may require printer service.
Turn the printer off and check all cable connections. Turn the printer back on. If the service message recurs, call for service and report the message number and description of the problem.


Select a menu from the following list for more information. Or, click a letter in the index at the bottom of the page to find a specific menu item that starts with that letter.
Click here for a one-page overview of all the menus and their menu items.
Select a menu or menu item for more details.
Finishing Menu Duplex Duplex Bind Copies Blank Pages Collation Separator Sheets Separator Source Multipage Print Multipage Order Multipage View Multipage Border Staple Job Staple Prime Src Offset Pages
Job Menu Confidential Job Held Jobs Cancel Job Reset Printer Print Buffer Prime Stapler Reset Active Bin
PCL Emul Menu Font Source Font Name Point Size Pitch Symbol Set Orientation Lines per Page A4 Width Tray Renumber Auto CR after LF Auto LF after CR
PostScript Menu Print PS Error Font Priority
USB Menu PCL SmartSwitch PS SmartSwitch NPA Mode USB Buffer Job Buffering MAC Binary PS
Paper Menu Paper Source Paper Size Paper Type Custom Types Universal Setup Output Bin Configure Bins Overflow Bin Assign Type/Bin Substitute Size Configure MP Envelope Enhance Paper Texture Paper Weight Paper Loading
Quality Menu Print Resolution Toner Darkness PQET PictureGrade
Utilities Menu Print Menus Print Net Setup Print Fonts Print Directory Factory Defaults Format Flash Defragment Flash Format Disk Job Acct Stat Hex Trace
LocalTalk Menu LocalTalk Port PCL SmartSwitch PS SmartSwitch NPA Mode LocalTalk Buffer Job Buffering NPA Hosts LocalTalk Name LocalTalk Addr LocalTalk Zone
Serial Menu PCL SmartSwitch PS SmartSwitch NPA Mode Serial Buffer Job Buffering RS-232/RS-422 RS-422 Polarity Serial Protocol Robust XON Baud Data Bits Parity Honor DSR Network Menu PCL SmartSwitch PS SmartSwitch NPA Mode Network Buffer Job Buffering Network Setup MAC Binary PS
Setup Menu Printer Language Power Saver Resource Save Download Target Print Timeout Wait Timeout Auto Continue Jam Recovery Page Protect Display Language Alarm Control Toner Alarm Staple Alarm Job Accounting
Infrared Menu Infrared Port PCL SmartSwitch PS SmartSwitch NPA Mode Infrared Buffer Job Buffering Window Size Transmit Delay Max Baud Rate
Parallel Menu PCL SmartSwitch PS SmartSwitch NPA Mode Parallel Buffer Job Buffering Advanced Status Protocol Honor Init Parallel Mode 1 Parallel Mode 2

Use the Finishing Menu to define how the printer delivers the printed output.
Select a menu item for more details:
To specify whether to include application-generated blank pages as part of your printed output.
Do Not Print* Does not print application-generated blank pages as part of your job.
Print Prints application-generated blank pages as part of your job.

To keep the pages of a print job stacked in sequence, particularly when printing multiple copies of the job.
Off* Prints each page of a job the number of times specified by the Copies menu item. For example, if you set Copies to 2 and send three pages to print, the printer prints page 1, page 1, page 2, page 2, page 3, page 3.
On Prints entire job the number of times specified by the Copies menu item. For example, if you set Copies to 2 and send three pages to print, the printer prints page 1, page 2, page 3, page 1, page 2, page 3.
To set the number of copies you want for the printer default value. (Set the number of copies required for a specific job from the printer driver. Values selected from the printer driver always override values selected from the operator panel.)
1...999 (1*)
Duplex
Purpose:
To set duplexing as the default for all print jobs. (Select Duplex from the printer driver to duplex only specific jobs.)
Off* Prints on one side of the paper.
On Prints on both sides of the paper.
Collation · Duplex Bind

To define the way duplexed pages would be bound, and how the printing on the back of the sheet (even-numbered pages) is oriented in relation to the printing on the front (odd-numbered pages).
Long Edge* Assumes binding along the long end of the page (left edge for portrait orientation and top edge for landscape orientation).
Short Edge Assumes binding along the short edge of the page (top edge for portrait orientation and left edge for landscape orientation).
Multipage Border
Purpose:
To print a border around each page image when using Multipage Print.
None* Does not print a border around each page image.
Solid Prints a solid line border around each page image.
Multipage Order
Purpose:
To determine the positioning of multiple page images when using Multipage Print. The positioning depends on the number of images and whether the images are portrait or landscape in orientation.

Multipage Print
Purpose:
To print multiple page images on one side of a sheet of paper. Also called N-Up or Paper Saver.
Off* Prints 1 page image per side. 6 Up Prints 6 page images per side.
2 Up Prints 2 page images per side. 9 Up Prints 9 page images per side.
3 Up Prints 3 page images per side. 12 Up Prints 12 page images per side.
4 Up Prints 4 page images per side. 16 Up Prints 16 page images per side.
Multipage Border; Multipage Order; Multipage View
To determine the orientation of a multipage sheet.
Auto* Lets the printer choose between portrait and landscape orientation.
Long Edge Sets the long edge of the paper as the top of the page (landscape).
Short Edge Sets the short edge of the paper as the top of the page (portrait).
Offset Pages
Purpose:
To offset the output of each print job or each copy of a print job, making it easier to separate the documents stacked in the output bin.
Multipage Print · Multipage Print

None* Stacks all sheets directly on top of each other.
Between Copies Offsets each copy of a print job.
Between Jobs Offsets each print job.
To insert blank separator sheets between jobs, between multiple copies of a job, or between each page of a job.
None* Does not insert separator sheets.
Between Copies Inserts a blank sheet between each copy of a job. If Collation is Off, a blank page is inserted between each set of printed pages (all page 1’s, all page 2’s, and so on). If Collation is On, a blank page is inserted between each collated copy of the job.
Between Jobs Inserts a blank sheet between jobs.
Between Pages Inserts a blank sheet between each page of a job. This is useful if you are printing transparencies or want to insert blank pages in a document for notes.
Separator Source; Collation
To specify the paper source that holds separator sheets.
Tray <x> (Tray 1*) Selects separator sheets from the specified tray.
MP Feeder Selects separator sheets from the multipurpose feeder. (You must also set Configure MP to Cassette.)
Env Feeder Inserts envelopes as separator sheets.
Separator Sheets; Configure MP

To set stapling as the default for all print jobs. (Select stapling from the printer driver if you want to staple only specific jobs.)
Off* Does not staple print jobs.
On Staples each multi-page print job sent to the printer.
To specify the paper source you want the printer to use when the Prime Stapler is selected from the Job Menu.
Tray <x> (Tray 1*) Selects paper from the specified tray.
MP Feeder Selects paper from the multipurpose feeder.
Manual Pap Selects a sheet of paper inserted in the manual feed slot.
Prime Stapler

Use the Infrared Menu to change printer settings affecting jobs sent to the printer through an infrared port.
Select a menu item for more details:
To configure the size of the infrared input buffer.
Disabled Disables job buffering. Any jobs already buffered on the disk are printed before normal processing of incoming jobs resumes.
Auto* Printer automatically calculates the Infrared Buffer size (recommended setting).
5K to maximum size allowed
User specifies the Infrared Buffer size. The maximum size setting depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the Infrared Buffer size, disable or reduce the size of the parallel, serial, network, LocalTalk, and USB buffers.
Resource Save

To activate the infrared port.
Disabled* Disables the infrared port and all other menu items in the Infrared Menu.
IR Option <x> Activates the specified infrared port.
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer print jobs to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.
To specify the rate at which data can be received through the infrared port.
The maximum baud possible for both the printer and the infrared adapter is automatically set during a power on reset. However, if your printer is situated in a bright or highly reflective environment, you may experience intermittent communication problems. If you do, select a lower baud for the infrared connection.

To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
On Printer performs NPA processing. If data is not in NPA format, it is rejected as bad data.
Off Printer does not perform NPA processing.
Auto* Printer examines the data to determine the format and then processes it appropriately.
To configure the printer so it automatically switches to PCL emulation when a print job received through the infrared port requires it, regardless of the default printer language.
On* Printer examines the data on the infrared interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.
PS SmartSwitch; Printer Language
To configure the printer so it automatically switches to PostScript emulation when a print job received through the infrared port requires it, regardless of the default printer language.
On* Printer examines data on the infrared interface and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.

PCL SmartSwitch; Printer Language
To define the amount of time, in seconds, the printer must wait before transmitting meaningful infrared data to the host computer, as well as the amount of time the printer requests that the host computer wait before transmitting infrared data.
Auto* Printer sets the Transmit Delay value during a power-on reset to maximize link performance (recommended).
None No delay is imposed by the printer. However, not all host computers can communicate without some transmission delays.
1...15 User selects a Transmit Delay value between 1 and 15 seconds. If you have trouble printing using the infrared port, selecting a high Transmit Delay value, such as 15, may resolve the problem.
To specify the maximum number of infrared frames the printer can receive before sending an acknowledgment to the host computer.
Auto* Printer sets the Window Size value during a power on reset to maximize link performance (recommended).
1 User sets the Window Size to one frame (1). If you have trouble printing using the infrared port, changing the Window Size menu item to 1 may resolve the problem. L

The Job Menu is only available when the printer is busy processing or printing a job, when a printer message is displayed, or when the printer is in Hex Trace mode. Press Menu to open the Job Menu.
Select a menu item for more details:
To cancel the current print job.
memory.

To print confidential jobs stored in printer memory. (When the confidential job prints, it is automatically deleted from printer memory.)
First select the user name associated with your confidential job.
Then enter the Personal Identification Number (PIN) associated with your Confidential Job:
Enter PIN Use the operator panel buttons to enter the PIN associated with your confidential job.
Then select a value:
Print All Jobs Prints all jobs associated with your user name and PIN.
Print A Job Prints the specified confidential job. Press Menu to scroll through the list of confidential jobs associated with your user name and PIN. Press Select to print a specific job.
Delete All Jobs Deletes all jobs associated with your user name and PIN.
Delete A Job Deletes the specified confidential job. Press Menu to scroll through the list of confidential jobs associated with your user name and PIN. Press Select to delete a specific job.
Copies Determines the number of copies printed for each confidential job. Press Menu to scroll through the list of confidential jobs associated with your user name and PIN. Press Select to specify the job you want to print. Press Menu to increase or decrease the number of copies, then press Select.
Held Jobs
Purpose:
To print Reserve Print, Repeat Print, or Verify Print jobs stored in printer memory.
First, select the user name associated with your confidential job.
Print All Jobs Prints all held jobs associated with your user name.
Print A Job Prints the specified held job. Press Menu to scroll through the list of held jobs. Press Select to print the specific job.
Delete All Jobs Deletes all held jobs associated with your user name.
Delete A Job Deletes the designated held job. Press Menu to scroll through the list of held jobs. Press Select to delete the job.
Copies Determines the number of copies for each held job. Press Menu to scroll through the list of held jobs. Press Select to specify the job you want to print. Press Menu to increase or decrease the number of copies, and then press Select.

To print any data stored in the print buffer.
displayed. The Waiting state occurs if an incomplete job is sent to the printer or an ASCII job, such as a print screen command, is printing.
To prepare the stapler for proper functioning after a staple cartridge is replaced or a staple jam is cleared. Priming Stapler is displayed, and the printer tests the stapler several times before returning to the Ready state.
To define the active bin as the start bin (the first bin to receive printed output) in a set of linked bins.
To reset the printer to the user default value for each menu item, delete all downloaded resources (fonts, macros, and symbol sets) stored in printer memory (RAM), and delete all data in the interface link buffer.

Use the LocalTalk Menu to change printer settings affecting jobs sent to the printer through a LocalTalk port.
Select a menu item for more details:
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer the print job to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.
To identify the LocalTalk Node number assigned to the printer. This menu item cannot be modified through the operator panel.

To configure the size of the LocalTalk input buffer.
Disabled Disables job buffering. Any jobs already buffered on the disk are printed before normal processing of incoming jobs resumes.
Auto* Printer automatically calculates LocalTalk Buffer size (recommended).
6K to maximum size allowed
User specifies the LocalTalk Buffer size. The maximum size depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the LocalTalk Buffer size, disable or reduce the size of the parallel, serial, network, infrared, and USB buffers.
LocalTalk Name
Purpose:
To identify the printer model name stored in printer memory. This menu item cannot be modified through the operator panel.
To activate the LocalTalk port.
Disabled* Disables the LocalTalk port and all other menu items in the LocalTalk Menu.
LTalk Option <x> Activates the specified LocalTalk port.
To identify the LocalTalk Zone provided by the LocalTalk network. This menu item cannot be modified through the operator panel.
Resource Save

To specify the maximum number of NPA host computers that can register for NPA alerts.
1...10 (2*)
To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
On Printer performs NPA processing. If data is not in NPA format, it is rejected as bad data.
Off Printer does not perform NPA processing.
Auto* Printer examines the data to determine the format and then processes it appropriately.
To configure the printer so it automatically switches to PCL emulation when a print job received through the LocalTalk port requires it, regardless of the default printer language.
On* Printer examines data on the LocalTalk interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.
PS SmartSwitch; Printer Language

To configure the printer so it automatically switches to PostScript emulation when a print job received through the LocalTalk port requires it, regardless of the default printer language.
On* Printer examines data on the LocalTalk interface and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.
PCL SmartSwitch; Printer Language

Use the Network Menu to change printer settings affecting jobs sent to the printer through a network port (either Standard Network or Network Opt ).
Select a menu item for more details:
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer jobs to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.

To configure the printer to process Macintosh binary PostScript print jobs.
On Printer processes raw binary PostScript print jobs from computers using the Macintosh operating system.
Off Printer filters PostScript print jobs using standard protocol.
Auto* Printer processes print jobs from computers using either Windows or Macintosh operating systems.
To configure the size of the network input buffer.
Auto* Printer automatically calculates the Network Buffer size (recommended setting).
3K to maximum size allowed
User specifies the Network Buffer size. The maximum size depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the Network Buffer size, disable or reduce the size of the parallel, serial, infrared, LocalTalk, and USB buffers.
Network <x> Setup
Purpose:
To configure an internal print server.
Values for this menu item are supplied by the specific print server. Select the menu item to see the available values.
Resource Save

To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
On Printer performs NPA processing. If data is not in NPA format, it is rejected as bad data.
Off Printer does not perform NPA processing.
Auto* Printer examines the data to determine the format and then processes it appropriately.
To configure the printer so it automatically switches to PCL emulation when a print job received through the network port requires it, regardless of the default printer language.
On* Printer examines data on the network interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.
PS SmartSwitch; Printer Language
To configure the printer so it automatically switches to PostScript emulation when a print job received through the network port requires it, regardless of the default printer language.
On* Printer examines data on the network interface connection and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.

PCL SmartSwitch; Printer Language

Use the Paper Menu to define the paper loaded in each paper tray and the default paper source and output bin.
Select a menu item for more details:
To send print jobs to a specific output bin based on the requested paper type.
Plain Paper Bin Envelope Bin
Card Stock Bin Letterhead Bin
Transparency Bin Preprinted Bin
Labels Bin Colored Bin
Bond Bin Custom <x> Bin (where <x> represents 1 through 6)
name is truncated to 14 characters. If two or more bins share the same name, the name only appears once in the Assign Type/Bin value list.

To determine which output bin(s) the printer uses for a particular job.
Mailbox* Sends print jobs to the output bin designated for that user.
Link Links all bins together as though they were one large bin. When one linked bin is full, the printer starts filling the next linked bin, and continues with each additional linked bin.
Mail Overflow Sends print jobs to the output bin designated for that user until it is full, and then sends jobs to the designated overflow bin.
Link Optional Links all optional output bins as though they were one large bin, while leaving the standard bin individually addressable.
Type Assignment Sends each job to the output bin specified for that paper type.
To determine when the printer selects paper loaded in the multipurpose feeder.
Cassette* Printer treats the multipurpose feeder like any other paper tray. If a print job requests a paper size or type that is only loaded in the multipurpose feeder, the printer pulls paper from the multipurpose feeder for the job.
Manual Printer treats the multipurpose feeder like a manual feed tray, and displays Load Manual when you need to insert a single sheet of paper in the feeder.
First Printer pulls paper from the multipurpose feeder until it is empty, regardless of the paper source or paper size requested for the job.
To specify the kind of paper associated with each of the Custom Types available in the Paper Type menu item.

user-defined name is truncated to 14 characters. If two or more custom types share the same name, the name only appears once in the Custom Types value list.
To ensure high quality printed envelopes and minimize envelope wrinkling.
Off Prints envelopes as any other printed material.
On* Modifies the printing process to prevent wrinkling as envelopes move through the fuser.
If Envelope Enhance is On, you may hear a tapping sound as the envelopes print. We recommend you leave Envelope Enhance set to On unless the tapping sound is too loud for your work area. To eliminate this sound, select Off. Print a few envelopes. If the quality of print is acceptable, leave Envelope Enhance set to Off. If envelopes crease or wrinkle, select On.
To specify the default bin for printed material.
truncated to 14 characters. If two or more bins share the same name, the name only appears once in the Output Bin value list.
To designate an output bin as the overflow bin. If Configure Bins is set to Mail Overflow and a specific output bin is full, the printer automatically diverts printed material to the overflow bin.

truncated to 14 characters. If two or more bins share the same name, the name only appears once in the Overflow Bin value list.
To properly handle preprinted paper loaded in a tray, whether the job is a duplexed job or a single-sided job.
First select a paper type:
Card Stock Load Colored Loading Ltrhead Loading Bond Loading
Labels Loading Custom <x> Loading Preprint Loading
Then select a value:
Duplex Notifies the printer that the specified paper type is loaded properly for duplex printing. If the printer receives a single-sided job using that paper type, the printer inserts blank pages as necessary to print the job properly on preprinted forms. This setting may slow single-sided printing.
Off* Printer assumes preprinted material is loaded for single-sided printing. Duplexed jobs may not print properly.
The name is truncated to 14 characters.
Standard Bin* · Bin <x> · Loading print material

To identify the default paper size for each paper source. For trays with automatic size sensing, only the value detected by the hardware is displayed.
First select a paper source:
Env Feeder Size MP Feeder Size
Then select a value (*denotes a country-specific factory default value):
Letter* A3 B4 10 Envelope* Folio
Legal A4* B5 DL Envelope* Statement
Executive A5 11x17 C5 Envelope
Universal Select Universal when you load paper that doesn’t match any of the other available sizes. The printer automatically formats the page for the maximum possible size. You can then set the actual page size from your application software.
To identify the default paper source.
Tray <x> (Tray 1*)
If you loaded the same size and type of paper in two paper sources (and the Paper Size and Paper Type menu items are correctly set), the trays are automatically linked. When one paper source is empty, paper automatically feeds from the next linked source.

To identify the texture of the paper loaded in a specific source and to ensure that characters print clearly.
First select a paper type:
Plain Texture Preprint Texture Labels Texture Ltrhead Texture
Card Stock Text Colored Texture Bond Texture
Trnsprncy Text Custom <x> Texture Envelope Texture
Then select a value:
available for a custom Type, then the name is displayed instead of Custom Texture. The name is truncated to 14 characters.
Use Paper Texture in connection with the Paper Type and Paper Weight menu items. You may need to change those menu items to optimize print quality for your specific paper.
Paper Type; Paper Weight
To identify the type of paper installed in each paper source.
First select a paper source:
Tray <x> Type Env Feeder Type MP Feeder Type
Manual Pap Type Manual Env Type
Then select a value:
Plain Paper Labels Preprinted Envelope
Card Stock Bond Colored Paper Preprinted
Transparency Letterhead Custom Type <x> Colored Paper
Smooth · Normal* · Rough

The Paper Type default for each envelope source is Envelope. The Paper Type default for each paper tray is as follows:
Tray 1–Plain Paper Tray 4–Custom Type 4
Tray 2–Custom Type 2 Tray 5–Custom Type 5
Tray 3–Custom Type 3 MP feeder–Custom Type 6
Manual Pap Type–Plain Paper
user-defined name is truncated to 14 characters. If two or more custom types share the same name, the name only appears once in the Paper Type value list.
Use this menu item to:
Paper Weight
Purpose:
To identify the relative weight of the paper loaded in a specific source and ensure that the toner adheres properly to the printed page.
First select a paper type:
Plain Weight Preprint Weight Bond Weight Labels Weight
Cardstock Weight Color Weight Envelope Weight Ltrhead Weight
Trnsprncy Weight Custom <x> Weight
Then select a value:
The name is truncated to 14 characters.

To have the printer substitute the specified paper size if the requested size is not loaded.
Off Printer prompts the user to load the requested paper size.
Letter/A4 Prints A4 size jobs on letter size paper if only letter size paper is loaded, and prints letter size jobs on A4 size paper if only A4 size paper is loaded.
Statement/A5 Prints A5 size jobs on statement size paper if only statement size paper is loaded, and prints statement size jobs on A5 paper if only A5 paper is loaded.
All Listed* Substitutes both Letter/A4 and Statement/A5.
To determine the default size when the Paper Size setting for a tray or feeder is Universal.
First select a unit of measure (* denotes a country-specific factory default value):
Then select the values:
Portrait Width 3.00–14.17 in. 76–360 mm
(8.50 in.*) (216 mm*)
Portrait Height 3.00–14.17 in. 76–360 mm
(14.17 in.*) (360 mm*)
Feed Direction Short Edge*

Use the PCL Emul Menu to change printer settings that only affect jobs using the PCL emulation printer language.
Select a menu item for more details:
To select the width of the logical page for A4 size paper.
198 mm* Makes the logical page compatible with the Hewlett-Packard LaserJet 5 Printer.
203 mm Makes the logical page wide enough to print eighty 10-pitch characters.

To specify whether the printer automatically performs a carriage return after a line feed control command.
Off* Printer does not perform a carriage return after a line feed control command.
On Printer performs a carriage return after a line feed control command.
To specify whether the printer automatically performs a line feed after a carriage return control command.
Off* Printer does not perform a line feed after a carriage return control command.
On Printer performs a line feed after a carriage return control command.
To choose a specific font from the specified font source.
The font name and font ID for all fonts in the selected font source are displayed. The font source abbreviation is R for resident, F for flash, K for disk, and D for download.
R0 Courier 10* · Font Source

To determine the set of fonts displayed in the Font Name menu item.
Resident* Displays all fonts resident in printer RAM when the printer ships from the factory.
Download Displays all fonts downloaded to printer RAM.
Flash Displays all fonts stored in flash memory.
Disk Displays all fonts stored on the printer hard disk.
All Displays all fonts available to the printer from all sources.
Lines per Page
Purpose:
To determine the number of lines that print on each page.
1...255
The printer sets the amount of space between each line (vertical line spacing) based on the Lines per Page, Paper Size, and Orientation menu items. Select the correct Paper Size and Orientation before changing Lines per Page.
Orientation; Paper Size
Font Name · 60* (country-specific) · 64* (country-specific)

To determine how text and graphics are oriented on the page.
Portrait* Prints text and graphics parallel to the short edge of the paper.
Landscape Prints text and graphics parallel to the long edge of the paper.
To specify the font pitch for scalable monospaced fonts.
0.08...100 (in increments of 0.01 cpi)
Pitch refers to the number of fixed-space characters in a horizontal inch of type. You can select a pitch from 0.08 to 100 characters per inch (cpi) in increments of 0.01 cpi. For nonscalable monospaced fonts, the pitch is displayed, but cannot be changed.
To change the point size for scalable typographic fonts.
1...1008 (in increments of 0.25 points)
Point size refers to the height of the characters in the font. One point equals approximately 1/72 of an inch. You can select point sizes from 1 to 1008 in increments of 0.25 points.
10* · 12*

To choose a symbol set for a specified font name.
A symbol set is a set of alphabetic and numeric characters, punctuation, and special symbols used when printing with a selected font. Symbol sets support the different requirements for languages or specific applications, such as math symbols for scientific text. Only the symbol sets supported for the selected font name are displayed.
Tray Renumber
Purpose:
To configure your printer to work with printer drivers or applications that use different source assignments for the paper trays.
First select a paper source:
Assign Tray <x> Assign Env Feeder Assign Man Env
Assign MP Feeder Assign Man Paper
Then select a value:
Off* Printer uses factory default paper source assignments.
0...199 Select a numeric value to assign a custom value to a paper source.
None Paper source ignores the Select Paper Feed command.
View Factory Def Displays the factory default value assigned to the specified paper source.
Restore Defaults Select Yes to return all tray assignments to factory default values.
numbers.
10U PC-8* (country-specific) · 12U PC-850* (country-specific) · Font Name

Use the Parallel Menu to change printer settings affecting jobs sent to the printer through a parallel port (either Std Parallel or Parallel Opt ).
Select a menu item for more details:
To enable bidirectional communication through the parallel port.
Off Disables parallel port negotiation.
On* Enables bidirectional communication through the parallel interface.

To determine whether the printer honors hardware initialization requests from the computer. The computer requests initialization by activating the INIT signal on the parallel interface. Many personal computers activate the INIT signal each time the computer is turned on and off.
Off* Printer does not honor hardware initialization requests from the computer.
On Printer honors hardware initialization requests from the computer.
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer print jobs to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.
To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
On Printer performs NPA processing. If data is not in NPA format, it is rejected as bad data.
Off Printer does not perform NPA processing.
Auto* Printer examines data and determines the format and then processes it appropriately.

To configure the size of the parallel input buffer.
Disabled Disables job buffering. Any jobs already buffered on the disk are printed before normal processing of incoming jobs resumes.
Auto* Printer automatically calculates the Parallel Buffer size (recommended setting).
3K to maximum size allowed
User specifies the Parallel Buffer size. The maximum size depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the Parallel Buffer size, disable or reduce the size of the serial, infrared, LocalTalk, and USB buffers.
Parallel Mode 1
Purpose:
To control the pull-up resistors on the parallel port signals. This menu item is useful for personal computers that have open collector outputs on the parallel port signals.
On Disables the resistors.
Off* Enables the resistors.
To determine whether the parallel port data is sampled on the leading or trailing edge of strobe.
On* Samples parallel port data on the leading edge of strobe.
Off Samples parallel port data on the trailing edge of strobe.
Resource Save

To configure the printer so it automatically switches to PCL emulation when a print job received through the parallel port requires it, regardless of the default printer language.
On* Printer examines data on the parallel interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.
Printer Language; PS SmartSwitch
To configure the printer so it automatically switches to PostScript emulation when a print job received through the parallel port requires it, regardless of the default printer language.
On* Printer examines data on the parallel interface and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.
PCL SmartSwitch; Printer Language
To specify the parallel interface protocol.
Standard May resolve some parallel interface problems.
Fastbytes* Provides compatibility with most existing parallel interface implementations (recommended setting).

Technical Reference L

Use the PostScript Menu to change printer settings that only affect jobs using the PostScript emulation printer language.
Select a menu item for more details:
To establish the font search order.
Resident* Printer searches printer memory for the requested font before searching flash memory or hard disk.
Flash/Disk Printer searches the hard disk and flash memory for the requested font before searching printer memory.
neither defective nor Read/Write or Write protected, and Job Buffer Size is not set to 100%.
To print a page defining the PostScript emulation error when an error occurs.
Off* Discards the print job without printing an error message.
On Prints an error message before it discards the job.

Use the Quality Menu to change printer settings affecting the quality of printed characters and images.
Select a menu item for more details:
To improve the quality of grayscale printing at 300 and 600 dots per inch (dpi) in PostScript emulation.
On* Uses modified screening parameters to improve print quality of graphics.
Off Uses standard screening parameters.
To improve the quality of text and make characters appear smoother when Print Resolution is set to 300 dots per inch (dpi).
Off Does not alter quality of text characters printed at 300 dpi.
On* Smooths characters with jagged or uneven edges.

To define the number of dots printed per inch (dpi). The higher the value, the sharper the clarity of printed characters and graphics.
300 dpi Offers a lower resolution printing option when memory is at a premium.
600 dpi* Produces high quality output for print jobs that are mostly text.
1200 Image Q Uses line screening for print jobs that contain bitmapped images, such as scanned photos.
1200 dpi Produces highest quality output for jobs where print speed is not important and memory is abundant.
To lighten or darken text images, or conserve toner.
Select a lower value for finer line width, higher definition in graphics, and lighter grayscale images. Select a higher value for bolder line widths or darker grayscale images. Select 10 for very bold text. Select a value less than 8 to conserve toner.
On the operator panel display, a vertical bar ( | ) indicates the factory default value. An arrow symbol ( V ) indicates a user default value.
3 8*

Use the Serial Menu to change printer settings affecting jobs sent to the printer through a serial port (either Standard Serial or Serial Opt ).
Select a menu item for more details:
To specify the rate at which data can be received through the serial port.
See also:

To specify the number of data bits that are sent in each transmission frame.
See also:
Honor DSR
Purpose:
To determine whether the printer uses the Data Set Ready (DSR) signal. DSR is one of the handshaking signals for most serial interface cables.
Off* All data received by the serial port is treated as valid data.
On Only data received while the DSR signal is high is treated as valid.
The serial interface uses DSR to distinguish data sent by the computer from data created by electrical noise in the serial cable. This electrical noise can cause stray characters to print. Select On to prevent stray characters from printing.
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer print jobs to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.
8* · Technical Reference

To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
On Printer performs NPA processing. If data is not in NPA format, it is rejected as bad data.
Off Printer does not perform NPA processing.
Auto* Printer examines the data to determine the format and then processes it appropriately.
To select the parity for serial input and output data frames.
See also:
PCL SmartSwitch
Purpose:
To configure the printer so it automatically switches to PCL emulation when a print job received through the serial port requires it, regardless of the default printer language.
On* Printer examines data on the serial interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.

PS SmartSwitch; Printer Language
To configure the printer so it automatically switches to PostScript emulation when a print job received through the serial port requires it, regardless of the default printer language.
On* Printer examines data on the serial interface and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.
PCL SmartSwitch; Printer Language
To determine whether the printer communicates availability to the computer.
Off* Printer waits to receive data from the computer.
On Printer sends a continuous stream of XONs to the host computer to indicate that the serial port is ready to receive more data.
This menu item only applies to the serial port if Serial Protocol is set to XON/XOFF.
To specify the type of serial communication.
RS-232*
RS-422

To establish the behavior of the positive and negative signals when using RS-422 serial communication.
Normal* Uses default definition of one and zero.
Reverse Reverses the definition of one and zero, thereby allowing a positive connection to a host computer negative terminal without changing the physical cable.
To configure the size of the serial input buffer.
Disabled Disables job buffering. Any jobs already buffered on the disk are printed before normal processing of incoming jobs resumes.
Auto* Printer automatically calculates the Serial Buffer size (recommended setting).
3K to maximum size allowed
User specifies the Serial Buffer size. The maximum size depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the Serial Buffer size, disable or reduce the size of the parallel, infrared, LocalTalk, and USB buffers.
Resource Save

To select the hardware and software handshaking values for the serial interface.
DTR* Hardware handshaking.
DTR/DSR Hardware handshaking.
XON/XOFF Software handshaking.
XON/XOFF/DTR Combined hardware and software handshaking.
XON/XOFF/DTRDSR Combined hardware and software handshaking.
Technical Reference

Use the Setup Menu to configure a variety of printer features.
Select a menu item for more details:
To establish whether the printer sounds an alarm when the printer requires operator intervention.
Off Printer does not sound an alarm.
Single* Printer sounds three quick beeps.
Continuous Printer repeats three beeps every 10 seconds.

To define the amount of time (in seconds) the printer waits after displaying an operator intervention error message before it resumes printing.
Disabled* Printer does not resume printing until someone clears the error message.
5...255 Printer waits the specified amount of time, and then automatically resumes printing. This timeout value also applies if the menus are displayed (and the printer is offline) for the specified period of time.
To determine the language of the text on the operator panel display.
To specify the storage location for downloaded resources.
RAM* All downloaded resources are automatically stored in printer memory (RAM).
Flash All downloaded resources are automatically stored in flash memory.
Disk All downloaded resources are automatically stored on the hard disk.
Storing downloaded resources in flash memory or on a hard disk is permanent storage rather than the temporary storage that RAM provides. The resources remain in the flash memory or on the hard disk even when the printer is turned off. Use MarkVision to download resources to the printer.

To establish whether the printer reprints jammed pages.
On Printer reprints jammed pages.
Off Printer does not reprint jammed pages.
Auto* Printer reprints a jammed page unless the memory required to hold the page is needed for other printer tasks.
To store statistical information about your most recent print jobs on the hard disk. The statistics include whether the job printed with or without errors, the print time, the job size (in bytes), the requested paper size and paper type, the total number of printed pages, and the number of copies requested.
Off* Printer does not store job statistics on disk.
On Printer stores job statistics for the most recent print jobs.
nor Read/Write or Write protected.
Page Protect
Purpose:
To successfully print a page that may otherwise generate Complex Page errors.
Off* Prints a partial page of data if memory is insufficient to process the entire page.
On Ensures that an entire page is processed before it prints.
If, after selecting On, you still cannot print the page, you may also have to reduce the size and number of fonts on the page, or increase the installed printer memory.
For most print jobs, you do not need to select On. When On is selected, printing may be slower.
Job Acct Stat

To specify the amount of time (in minutes) the printer waits after a job is printed before it goes into a reduced power state.
Disabled Disables Power Saver; the fuser remains warm and ready to print at all times.
1...240 Specifies the amount of time after a print job before the printer goes into Power Saver mode. (Your printer may not support the entire range of values.)
The factory default Power Saver setting depends on your printer model. Print the menu settings page to determine the current Power Saver setting. When the printer is in Power Saver mode, it is still ready to receive print jobs.
Select 1 to put the printer in Power Saver mode one minute after it finishes a print job. This uses much less energy, but requires more warm-up time for the printer. Select 1 if your printer shares an electrical circuit with room lighting and you notice lights flickering.
Select a high value if your printer is in constant use. Under most circumstances, this keeps the printer ready to print with minimum warm-up time. Select a value between 1 and 240 minutes if you want a balance between energy consumption and a shorter warm-up period.
If the Disabled value is not available from the Power Saver menu item, see Disabling Power Saver for more information.
To specify the amount of time (in seconds) the printer waits before printing the last page of a print job that does not end with a command to print the page. The print timeout counter does not start until Waiting is displayed.
Disabled The printer does not print the last page of a print job until one of the following occurs:
1...225 (90*) The printer prints the last page after the specified time.
Print Buffer

To establish the default printer language used to communicate data from the computer to the printer.
PCL Emulation* PCL emulation, compatible with Hewlett-Packard printers.
PS Emulation PostScript emulation, compatible with Adobe PostScript language.
from sending print jobs that use the other language.
To determine what the printer does with downloaded resources, such as fonts and macros stored in RAM, if the printer receives a job that requires more memory than is available.
Off* Printer retains downloaded resources only until memory is needed. It then deletes those resources associated with the inactive printer language.
On Printer retains all downloaded resources for all printer languages during language changes and printer resets. If the printer runs out of memory, 38 Memory Full is displayed.
To specify how the printer responds when it is out of staples.
Off* Staples Empty is displayed until someone loads staples.
Single Printer stops printing, displays Staples Empty, and sounds three quick beeps.
Continuous Printer stops printing, displays Staples Empty, and repeats three beeps every 10 seconds until the staple cartridge is replaced.

To specify how the printer responds when it is out of toner.
Off* An error message is displayed until someone replaces the print cartridge. If an Auto Continue value is selected from the Setup Menu, the printer resumes printing after the specified timeout value.
Single Printer stops printing, displays an error message, and sounds three quick beeps.
Continuous Printer stops printing, displays an error message, and repeats three beeps every 10 seconds until the print cartridge is replaced.
Wait Timeout
Purpose:
To specify the amount of time (in seconds) the printer waits to receive additional bytes of data from the computer. When this timeout expires, the print job is canceled.
Disabled Disables Wait Timeout.
15...65535 (40*) Specifies the amount of time the printer waits for additional data before it cancels the job.
has no effect on PCL emulation print jobs.
Auto Continue

Use the Utilities Menu to print a variety of listings relating to available printer resources, printer settings, and print jobs. Other menu items let you set up printer hardware and troubleshoot printer problems.
Select a menu item for more details:
To retrieve storage area lost when resources are deleted from flash memory.
Yes Printer transfers all resources stored in flash memory to printer memory and then reformats the flash memory option. When the format operation is complete, the resources are loaded back into flash memory.
No Printer cancels the request to defragment the flash memory.
WARNING: Do not turn off the printer while the flash is defragmenting.

To return your printer settings to the factory default values.
Restore • All menu items are returned to the factory default values except: – Display Language. – All settings in the Parallel Menu, Serial Menu, Network Menu, Infrared
Menu, LocalTalk Menu, and USB Menu. • All downloaded resources (fonts, macros, and symbol sets) in printer memory (RAM) are deleted. (Resources residing in flash memory or on the hard disk are unaffected.)
Do Not Restore User-defined settings remain.
To format the printer hard disk.
Yes Deletes any data stored on the hard disk and prepares the device to receive new resources.
No Cancels the request to format the hard disk and leaves current resources stored on the disk.
WARNING: Do not turn off the printer while the hard disk is formatting.
To format the flash memory.
Yes Deletes any data stored in flash memory and prepares the flash memory to receive new resources.
No Cancels the request to format the flash memory and leaves current resources stored in flash memory.
WARNING: Do not turn off the printer while the flash is formatting.

To help isolate the source of a print job problem. With Hex Trace selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed.
To exit Hex Trace, turn the printer off or reset the printer from the Job Menu.
To print a listing of all job statistics stored on the hard disk, or to clear all statistics on the disk.
Print Prints all statistics available for the most recent print jobs.
Clear Deletes all accumulated job statistics from the hard disk.
Print Directory
Purpose:
To print a list of all the resources stored in flash memory or on the hard disk.
and formatted, and Job Buffer Size is not set to 100%.
Print Fonts
Purpose:
To print a sample of all the fonts available for the selected printer language.
PCL Fonts Prints a sample of all printer fonts available for PCL emulation.
PS Fonts Prints a sample of all printer fonts available for PostScript emulation.
Job Accounting · Technical Reference

To print a listing of the current user default values, the installed options, the amount of installed printer memory, and the status of printer supplies.
To print information relating to the internal print server and the network settings defined by the Network Setup menu item in the Network Menu.
Network <x> Setup

Use the USB Menu to change printer settings affecting a Universal Serial Bus (USB) port (USB Option or Standard USB).
Select a menu item for more details:
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer print jobs to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.
To configure the printer to process Macintosh binary PostScript print jobs.

On Printer processes raw binary PostScript print jobs from computers using the Macintosh operating system.
Off Printer filters PostScript print jobs using standard protocol.
Auto* Printer accepts print jobs from computers using either Windows or Macintosh operating systems.
To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
On Printer performs NPA processing. If data is not in NPA format, it is rejected as bad data.
Off Printer does not perform NPA processing.
Auto* Printer examines the data to determine the format and then processes it appropriately.
To configure the printer so it automatically switches to PCL emulation when a print job received through the USB port requires it, regardless of the default printer language.
On* Printer examines the data on the USB interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.
PS SmartSwitch; Printer Language

To configure the printer so it automatically switches to PostScript emulation when a print job received through the USB port requires it, regardless of the default printer language.
On* Printer examines data on the USB interface and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.
PCL SmartSwitch; Printer Language
To configure the size of the USB input buffer.
Disabled Job buffering is disabled. Any jobs already buffered on the disk are printed before normal processing of incoming jobs resumes.
Auto* Printer automatically calculates the USB Buffer size (recommended setting).
3K to maximum size allowed
User specifies the USB Buffer size. The maximum size depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the USB Buffer size, disable or reduce the size of the parallel, serial, network, infrared, and LocalTalk buffers.
Resource Save

Keep the following guidelines in mind when removing any options:
For more information, click a topic:

Follow these instructions to remove a finisher, 5-bin mailbox, high-capacity output stacker, or output expander. The following steps explain how to remove an output expander as an example.
1 If you are removing the topmost output option and do not plan to return it to that position, remove the top cover.
If you are removing a finisher, skip to step 4.

You must attach the top cover to the printer or topmost output option when you finish removing output options. In addition, it may be necessary to remove the paper bail from the top cover, depending on the type of output option to which it is attached. Refer to the Setup Guide for more information.
2 Detach the output expander tray.
If you are removing a 5-bin mailbox or high-capacity output stacker, skip to step 3.
a Lift the edge of the tray so the lower tabs come out of the slots on the output expander.


b Pull the tray straight out toward you to remove the upper tabs from the output expander slots.

3 The output option may have a wire paper bail attached. If so, remove the tips of the paper bail from the ends of the plastic bracket on the bottom of the output option.
Refer to the Setup Guide when you are ready to reattach the paper bail to an output option.
4 Carefully lift the option straight up until it is completely disconnected from the option below it or from the printer. Set it aside.
WARNING: The edges of the mounting brackets could damage tabletops or fabrics.
5 Refer to the Setup Guide when you are ready to reattach options.


2 Push the envelope support to the closed position.
4 ull the envelope feeder up slightly and straight out of the printer. Set it aside.

5 Close both front doors.
6 Refer to the Setup Guide when you are ready to reattach options.
1 Ask someone to help you lift the printer by the handholds and set it aside.

Handhold

2 Carefully lift the option straight up until it is completely disconnected from the option below it. Set it aside.

3 Refer to the Setup Guide when you are ready to reattach options.
If necessary, refer to the Setup Guide for instructions on accessing the printer system board.
1 Locate the memory option you want to remove.
metal on the printer before you touch the memory option.
2 Push out on the latches at each end of the connector.

Latch

3 Pull the memory option out of the connector.
4 Place the memory option in its original packaging. If you did not save the packaging, wrap it in paper and store it in a box.

5 If you need to install a replacement memory option or other option on the system board, refer to the Setup Guide.
6 Refer to the Setup Guide for instructions on closing the printer system board.
If necessary, refer to the Setup Guide for instructions on accessing the printer system board.
metal on the printer before you touch the card.
2 Loosen and remove the two screws over and under the slot. Gently pull the card out of the connector on the system board.
3 Place the option card in its original packaging. If you did not save the packaging, wrap the card in paper and store it in a box.
4 If you need to install another option on the system board, refer to the Setup Guide.
5 Refer to the Setup Guide for instructions on closing the printer system board.

If you always want your printer ready to print without delays, you may want to disable Power Saver in the Setup Menu. If the Disabled value is not available, first change the Energy Conserve setting to Off in the Config Menu:
1 Turn the printer off.
2 Press and hold the Select and Return buttons, and then turn the printer on.
3 Release the buttons when Performing Self Test appears on the display.
When the printer self test is done, Config Menu is displayed.
4 Press Menu until you see Energy Conserve, and then press Select.
5 Press Menu until you see Off, and then press Select.
Energy Conserve SAVED briefly appears, and then Config Menu is displayed.
6 Press Menu until you see Exit Config Menu, and then press Select.
Activating Menu Changes briefly appears, followed by Performing Self Test. The printer then displays the Ready message.
Now you can select the Disabled value from the Power Saver menu item.
command. For more information, refer to the Technical Reference available on Lexmark’s Web site at www.lexmark.com.

Dimensions
Dimension T620 and T622
404 mm (15.9 in.)
538 mm (21.2 in.)
Width 418 mm (16.5 in.)
Depth 513 mm (20.2 in.)
20.4 kg (45 lb)
23.6 kg (52 lb)3
1 Includes printer and optional 500-sheet drawer. 2 Includes print cartridge. 3 Includes printer and optional 500-sheet drawer.
T620 and T622 T622(n) T620 and T622 T620(n)
Up to 200,000 pages per month Up to 130,000 pages per month


The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
Comments about this publication may be addressed to Lexmark International, Inc., Department F95/ 032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In the United Kingdom and Eire, call 0628-481500. In other countries, contact your point of purchase.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
Lexmark and Lexmark with diamond design, MarkNet, MarkVision, and Prebate are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
PictureGrade is a trademark of Lexmark International, Inc. LEXFAX and Operation ReSource are service marks of Lexmark International, Inc.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
PostScript® is a registered trademark of Adobe Systems Incorporated. PostScript 3 is Adobe Systems’ designation of a set of printer commands (language) and functions included in its software products. This printer is intended to be compatible with the PostScript 3 language. This means the printer recognizes PostScript 3 commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
Details relating to compatibility are included in the Technical Reference.
January 2001

The following terms are trademarks or registered trademarks of these companies:
Helvetica Linotype-Hell AG and/or its subsidiaries
ITC Avant Garde International Typeface Corporation
Times New Roman The Monotype Corporation plc
Zapf Chancery International Typeface Corporation
Other trademarks are the property of their respective owners.
© Copyright 2001 Lexmark International, Inc. All rights reserved.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and in applicable FAR provisions: Lexmark International, Inc., Lexington, KY 40550.
specified herein may result in hazardous radiation exposure.
software.

Federal Communications Commission (FCC) Compliance Information Statement
The T620 and T622 has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Class A computing device, use a properly shielded and grounded cable such as Lexmark part number 1329605. Use of a substitute cable not properly shielded and grounded may result in a violation of FCC regulations.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.
A declaration of conformity with the requirements of the Directive has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boigny, France.
This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950.
WARNING: When a print server is installed, this is a Class A product. In a domestic
environment, this product may cause radio interference, in which case, the user may be required to take adequate measures.

Federal Communications Commission (FCC) Compliance Information Statement
The T620 and T622 has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Class B computing device, use a properly shielded and grounded cable such as Lexmark part number 1329605. Use of a substitute cable not properly shielded and grounded may result in a violation of FCC regulations.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.
A declaration of conformity with the requirements of the Directive has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boigny, France.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.

This apparatus is approved under the approval number NS/G/1234/J/100003 for the indirect connections to the public telecommunications systems in the United Kingdom.
The EPA ENERGY STAR Computers program is a partnership effort with computer manufacturers to promote the introduction of energy-efficient products and to reduce air pollution caused by power generation.
Companies participating in this program introduce personal computers, printers, monitors, or fax machines that power down when they are not being used. This feature will cut the energy used by up to 50 percent. Lexmark is proud to be a participant in this program.
As an Energy Star Partner, Lexmark International, Inc. has determined that this product meets the Energy Star guidelines for energy efficiency.

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 825.

Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 5 milliwatt gallium arsenide laser operating in the wavelength region of 770-795 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.








Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2001 Lexmark International, Inc. 740 West New Circle Road Lexington, Kentucky 40550
Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Operator panel displays only diamonds or is blank. | • Turn the printer off, wait about 10 seconds, and turn the printer on. • Performing Self Test appears on the operator panel. When the test is completed, Ready is displayed. If the messages do not appear, turn the printer off and call the Lexmark Customer Support Center. | p.94 | |
| Menu settings changed from the operator panel have no effect. | Settings in the software application, the printer driver, or the printer utilities are overriding the settings made from the operator panel. • Change the menu settings from the printer driver, the printer utilities, or the software application instead of the operator panel. • Disable the settings in the printer driver, the printer utilities, or the software application so you can change settings from the operator panel. | p.94 | |
| Job did not print or incorrect characters printed. | Make sure Ready appears on the operator panel before you send a job to print. Press Go to return to Ready. | p.95 | |
| Job did not print or incorrect characters printed. | Make sure there is print material loaded in the printer. Press Go to return to Ready. | p.95 | |
| Job did not print or incorrect characters printed. | Verify that the printer is using the correct printer language. | p.95 | |
| Job did not print or incorrect characters printed. | Verify that you are using the correct printer driver. | p.95 | |
| Job did not print or incorrect characters printed. | Make sure the parallel, serial, ethernet, or USB cable is firmly plugged in at the back of the printer. Make sure you are using the correct cable. Use IEEE 1284-compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft). If you use RS-232 Serial, verify that a null modem cable is used. | p.95 | |
| Job did not print or incorrect characters printed. | If the printer is connected through a switch box, try a direct connection. | p.95 | |
| Job did not print or incorrect characters printed. | Verify that the correct paper size is selected through the operator panel, in the printer driver, or in the software application. | p.95 | |
| Job did not print or incorrect characters printed. | Make sure PCL SmartSwitch and PS SmartSwitch are set to On. | p.95 | |
| Job did not print or incorrect characters printed (continued). | If you are using a print spooler, verify that the spooler is not stalled. | p.95 | |
| Job did not print or incorrect characters printed (continued). | If you print across a network or on a Macintosh computer, see Network printing problems. | p.95 | |
| Job did not print or incorrect characters printed (continued). | Check the printer interface from the Setup Menu. Determine which host interface you are using. Print a menu settings page to verify that the current interface settings are correct. See Printing the menu settings page. If you are using a serial interface: • Make sure Honor DSR is set to Off. • Check the protocol, baud, parity, and data bit settings. The settings on the printer and on the host computer should match. | p.95 | |
| Printer is connected to the USB port, but will not print. | Make sure you are using Windows 98, Windows 2000, Windows Me, or another USB-capable operating system supported by Lexmark. | p.95 | |
| Print material misfeeds or multiple feeds occur. | Make sure the print material you are using meets the specifications for your printer. See Print material specifications for more details. | p.95 | |
| Print material misfeeds or multiple feeds occur. | Flex print material before loading it in any of the paper sources. | p.95 | |
| Print material misfeeds or multiple feeds occur. | Make sure the print material is loaded correctly. | p.95 | |
| Print material misfeeds or multiple feeds occur (continued). | Make sure the paper width and length guides on the paper sources are adjusted correctly. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Do not overfill the paper sources. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Do not force print material into the multipurpose feeder when you load it; otherwise, it may skew or buckle. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Remove any curled print material from paper sources. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Load the recommended print side correctly for the type of print material you are using. See Loading print material for more information. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Load less print material in the paper sources. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Turn the print material over or around and try printing again to see if feeding improves. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Do not mix print material types. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Do not mix reams of print material. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Remove the top and bottom sheets of a ream before loading the print material. | p.96 | |
| Print material misfeeds or multiple feeds occur (continued). | Load a paper source only when it is empty. | p.96 | |
| Envelope misfeeds or multiple feeds occur. | Remove the stack of envelopes from the envelope feeder. Load one envelope, feed it through the printer, and then reload the stack of envelopes in the envelope feeder. | p.96 | |
| Page breaks in unexpected places. | Check the Print Timeout setting in the Setup Menu. Increase the setting. | p.96 | |
| Job prints from the wrong paper source or on the wrong print material. | Check the Paper Type setting in the Paper Menu from the printer operator panel and in the printer driver. | p.96 | |
| Paper does not stack neatly in any output bin. | • Turn the paper stack over in the tray or multipurpose feeder. • Make sure you are using a paper size compatible with your output options. See Print material specifications. | p.96 | |
| Printer does not duplex pages. | • Make sure Duplex is selected in both the Finishing Menu and in the printer driver. • Make sure you have enough printer memory installed. | p.96 | |
| Print is too light. | • The toner may be low. To utilize the remaining toner, remove the cartridge by gripping the handles with both hands. With the cartridge arrows pointing downward, shake the print cartridge back and forth. Reinstall the cartridge and then press Go. • Change the Toner Darkness setting in the Quality Menu. • If you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper Menu. See Paper Type. • Verify that the correct print material is being used. | p.97 | |
| Toner smears or print comes off the page. | • If you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper Menu. See Paper Type. • Verify that the print material is within the printer specifications. See Print material specifications for more details. • If the problem continues, call the Lexmark Customer Support Center. | p.97 | |
| Toner appears on the back of the printed page. | Toner is on the transfer roll. To help prevent this, do not load print material that is smaller than the page size of the job to be printed. Open and close the printer upper front door to run the printer setup cycle and clean the transfer roll. | p.97 | |
| Toner fog or background shading appears on the page. | • Check the print cartridge to make sure it is installed correctly. • Change the print cartridge. See Replacing the print cartridge for more details. • If the problem continues, change the charge roll. See Replacing the charge roll for more details. | p.98 | |
| Entire page is white. | • Make sure the packaging material is removed from the print cartridge. • Check the print cartridge to be sure it is installed correctly. • The toner may be low. To utilize the remaining toner, remove the cartridge by gripping the handles with both hands. With the cartridge arrows pointing downward, shake the print cartridge back and forth. Reinstall the cartridge and then press Go. | p.98 | |
| Streaks appear on the page. | • The toner may be low. To utilize the remaining toner, remove the cartridge by gripping the handles with both hands. With the cartridge arrows pointing downward, shake the print cartridge back and forth. Reinstall the cartridge and then press Go. • If you are using preprinted forms, make sure the ink can withstand temperatures of 212°C (414°F). | p.98 | |
| Printing is too dark. | Change the Toner Darkness setting in the Quality Menu. Note: Macintosh computer users should make sure the lines per inch (lpi) setting is not set too high in the software application. | p.98 | |
| Characters have jagged or uneven edges. | • Change the Print Resolution setting in the Quality Menu to 600 dpi or 1200 dpi. • Turn PQET in the Quality Menu to On. • If you are using downloaded fonts, verify that the fonts are supported by the printer, the host computer, and the software application. | p.99 | |
| Part or all of the page is printed in black. | • Check the print cartridge to see if it is installed correctly. • If the charge roll has been replaced, verify that it is installed correctly. | p.99 | |
| The job prints, but the top and side margins are incorrect. | • Make sure the Paper Size setting in the Paper Menu is correct. • Make sure the margins are set correctly in your software application. L | p.99 | |
| I need to get updated printer drivers or utilities. | • Refer to the drivers CD that came with your printer. It contains printer drivers and utilities. • Visit the Lexmark Web site, www.lexmark.com, for the most current printer drivers or utilities. | p.103 | |
| I need to attach a serial cable to the printer. | If your printer is configured with a serial port, or you have installed an optional interface card, refer to the Setup Guide. | p.103 | |
| I can’t find the printer escape codes. | Refer to the Technical Reference available on the Lexmark Web site at www.lexmark.com. | p.103 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.