EN
LevelOne logo
Official user manual

LevelOne IFE-0502

21 pages·522 KB·Switch·PDF·ENDEFRITNLJA
LevelOne IFE-0502
Table of Contents 21 sections Introduction · Features · Package Contents · Hardware Description · … ShowHide
Page 1 of the LevelOne IFE-0502 user manual — LevelOne
Page 1 · click to enlarge
Page 1
LevelOne IFE-0502 diagram (page 1)
Fig. 1

LevelOne

IFE-0501/IFE-0502

4-Port PoE + 1-Port SC Industrial Fast Ethernet Switch

User Manual

Ver. 1.0.0-0711

Page 2 of the LevelOne IFE-0502 user manual — CE Mark Warning
Page 2 · click to enlarge
Page 2

FCC Warning

This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: „ Reorient or relocate the receiving antenna. „ Increase the separation between the equipment and receiver. „ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. „ Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Page 4 of the LevelOne IFE-0502 user manual — Features
Page 4 · click to enlarge
Page 4

Introduction

The 4-Port PoE + 1-Port SC Industrial Fast Ethernet Switch is a cost-effective solution and meets the high reliability requirements demanded by industrial applications. Using fiber port can extend the connection distance that increases the network elasticity and performance. In addition, the industrial switch provides the PoE function for kinds of Powered Devices to receive power as well as data over the RJ-45 cable.

Features

„ System Interface/Performance y RJ-45 ports support Auto MDI/MDI-X Function y Embedded 4-port PoE Injection y Store-and-Forward Switching Architecture y Back-plane (Switching Fabric): 1.0Gbps y 1K MAC Address Table y Fiber cable up to 2km by Full-duplex Multi-mode(IFE-0501) y Fiber cable up to 30km by Full-duplex Single-mode(IFE-0502) „ Power Supply y DC 48V Redundant Power (Full load with PoE) y Overload Current Re-settable Fuse Present „ Case/Installation y IP-30 Protection y DIN Rail and Wall Mount Design „ Provides EFT protection 3,000 VDC for power line „ Supports 4,000 VDC Ethernet ESD protection

Page 5 of the LevelOne IFE-0502 user manual — Package Contents
Page 5 · click to enlarge
Page 5

Package Contents

Please refer to the package contents list below to verify them against the checklist. „ IFE-0501(or IFE-0502) „ CD Manual „ Pluggable Terminal Block (attached on the switch) „ 2 wall mount plates with screws „ One DIN-Rail (attached on the switch) Compare the contents of the industrial switch with the standard checklist above. If any item is damaged or missing, please contact the local dealer for service.

Page 6 of the LevelOne IFE-0502 user manual — Front Panel
Page 6 · click to enlarge
Page 6

Hardware Description

In this paragraph, the Industrial switch’s hardware spec, port, cabling information, and wiring installation will be described.

Physical Dimension

4-Port PoE + 1-Port SC Industrial Fast Ethernet Switch dimension (W x D x H) is 30mm x 95mm x 140mm

Front Panel

The Front Panel of the 4-Port PoE + 1-Port Multi-mode SC Industrial Fast Ethernet Switch is shown as below:

LevelOne IFE-0502 — Front Panel diagram (page 6)
Fig. 2 · Front Panel
LevelOne IFE-0502 — Front Panel diagram (page 6)
Fig. 3 · Front Panel
LevelOne IFE-0502 — Front Panel diagram (page 6)
Fig. 4 · Front Panel
LevelOne IFE-0502 — Front Panel diagram (page 6)
Fig. 5 · Front Panel
LevelOne IFE-0502 — Front Panel diagram (page 6)
Fig. 6 · Front Panel
LevelOne IFE-0502 — Front Panel diagram (page 6)
Fig. 7 · Front Panel
LevelOne IFE-0502 — Front Panel diagram (page 6)
Fig. 8 · Front Panel
LevelOne IFE-0502 — Front Panel diagram (page 6)
Fig. 9 · Front Panel
LevelOne IFE-0502 — Front Panel diagram (page 6)
Fig. 10 · Front Panel

Front Panel of the IFE-0501 Industrial Fast Ethernet Switch

Page 7 of the LevelOne IFE-0502 user manual — Top View
Page 7 · click to enlarge
Page 7

The Front Panel of the 4-Port PoE + 1-Port Single-mode SC Industrial Fast Ethernet Switch is shown as below:

LevelOne IFE-0502 — Top View diagram (page 7)
Fig. 11 · Top View
LevelOne IFE-0502 — Top View diagram (page 7)
Fig. 12 · Top View
LevelOne IFE-0502 — Top View diagram (page 7)
Fig. 13 · Top View
LevelOne IFE-0502 — Top View diagram (page 7)
Fig. 14 · Top View
LevelOne IFE-0502 — Top View diagram (page 7)
Fig. 15 · Top View
LevelOne IFE-0502 — Top View diagram (page 7)
Fig. 16 · Top View
LevelOne IFE-0502 — Top View diagram (page 7)
Fig. 17 · Top View
LevelOne IFE-0502 — Top View diagram (page 7)
Fig. 18 · Top View

Front Panel of the IFE-0502 Industrial Fast Ethernet Switch

Top View

The top view of the 4-Port PoE + 1-Port SC Industrial Fast Ethernet Switch has one terminal block connector of two DC power inputs.

LevelOne IFE-0502 — Top View diagram (page 7)
Fig. 19 · Top View

Top View of the IFE-0501/IFE-0502 Industrial Fast Ethernet Switch

Page 8 of the LevelOne IFE-0502 user manual — LED Indicators
Page 8 · click to enlarge
Page 8

LED Indicators

The diagnostic LEDs located on the front panel of the industrial switch provide real-time information of system and optional status. The following table provides the description of the LED status and their meanings for the switch.

LevelOne IFE-0502 — LED Indicators diagram (page 8)
Fig. 20 · LED Indicators

On Power input 1 is active P1 Green Off Power input 1 is inactive

On Power input 2 is active P2 Green Off Power input 2 is inactive

On Power input 1 or 2 has failed Fault Red Off Power input 1 and 2 are both functional, or no power inputs

On The port is supplying power to the powered-device FWD (1 ~ 4) Green

Flashing Networking is active 5 LNK/ACT (fiber port) Green

Page 9 of the LevelOne IFE-0502 user manual — Ports
Page 9 · click to enlarge
Page 9

Ports

„ RJ-45 ports The UTP (RJ-45) Fast Ethernet ports will auto-sense for 10Base-T or 100Base-TX connections. Auto MDI/MDIX means that the switch can connect to another switch or workstation without changing straight through or crossover cabling. See the below figures for straight through and crossover cable schematic. „ RJ-45 Pin Assignments

LevelOne IFE-0502 — Ports diagram (page 9)
Fig. 21 · Ports
Pin NumberAssignment 1Tx+ 2Tx- 3Rx+ 6Rx-

“+” and “-” signs represent the polarity of the wires that make up

each wire pair.

All ports on this industrial switch support automatic MDI/MDI-X operation, user can use straight-through cables (See figure below) for all network connections to PCs or servers, or to other switches or hubs. In straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are connected straight through to pins 1, 2, 3 and 6 at the other end of the cable. The table below shows the 10BASE-T/100BASE-TX MDI and MDI-X port pin outs.

LevelOne IFE-0502 — Ports diagram (page 9)
Fig. 22 · Ports
Pin MDI-XSignal NameMDI Signal Name 1Receive Data plus (RD+)Transmit Data plus (TD+) 2Receive Data minus (RD-)Transmit Data minus (TD-) 3Transmit Data plus (TD+)Receive Data plus (RD+) 6Transmit Data minus (TD-)Receive Data minus (RD-)
Page 10 of the LevelOne IFE-0502 user manual — ATTENTION
Page 10 · click to enlarge
Page 10
LevelOne IFE-0502 — Ports diagram (page 10)
Fig. 23 · Ports

Straight Through Cable Schematic

LevelOne IFE-0502 — Ports diagram (page 10)
Fig. 24 · Ports

Cross Over Cable Schematic „ Fiber Port The fiber port of SC type connector can work in multi-mode (2Km) or single-mode (30Km). When you connect the fiber port to another one, please follow the figure below to connect accordingly. Wrong connection will cause the port cannot work normally.

LevelOne IFE-0502 — Ports diagram (page 10)
Fig. 25 · Ports

ATTENTION

This is a Class 1 Laser/LED product. Don’t stare into the Laser/LED Beam.

Page 11 of the LevelOne IFE-0502 user manual — Cabling
Page 11 · click to enlarge
Page 11

Cabling

„ Twisted-pair segment can be connected with unshielded twisted pair (UTP) or shielded twisted pair (STP) cable. The cable must comply with the IEEE 802.3u 100Base TX standard for Category 5. The cable between the converter and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long. „ Fiber segment using single-mode connector type must use 9/125µm single-mode fiber cable. „ Fiber segment using multi-mode connector type must use 50 or 62.5/125 µm multi-mode fiber cable.

Page 12 of the LevelOne IFE-0502 user manual — Wiring the Power Inputs
Page 12 · click to enlarge
Page 12

Wiring the Power Inputs

Please follow the steps below to insert the power wire.

LevelOne IFE-0502 — Wiring the Power Inputs diagram (page 12)
Fig. 26 · Wiring the Power Inputs

Insert the positive and negative wires into the V+ and V- contacts on the terminal block connector.

LevelOne IFE-0502 — Wiring the Power Inputs diagram (page 12)
Fig. 27 · Wiring the Power Inputs

Tighten the wire-clamp screws for preventing the wires from loosing.

Page 13 of the LevelOne IFE-0502 user manual — Wiring the Fault Alarm Contact
Page 13 · click to enlarge
Page 13

Wiring the Fault Alarm Contact

The fault alarm contact is in the middle of terminal block connector as the picture shows below. When the wires are inserted into ports 3 and 4, they automatically detect the fault status in the event of a power failure by forming an open circuit. An example for the fault alarm contact is shown as below:

LevelOne IFE-0502 — Wiring the Fault Alarm Contact diagram (page 13)
Fig. 28 · Wiring the Fault Alarm Contact

Insert the wires into the fault alarm contact.

The wire gauge for the terminal block should be in the range

between 12 ~ 24 AWG.

Page 14 of the LevelOne IFE-0502 user manual — DIN-Rail Mounting
Page 14 · click to enlarge
Page 14

Mounting Installation

DIN-Rail Mounting

The DIN-Rail is screwed on the industrial switch when out of factory. If the DIN-Rail is not screwed on the industrial switch, please see the following pictures to screw the DIN-Rail on the switch. Follow the steps below to hang the industrial switch.

LevelOne IFE-0502 — DIN-Rail Mounting diagram (page 14)
Fig. 29 · DIN-Rail Mounting
LevelOne IFE-0502 — DIN-Rail Mounting diagram (page 14)
Fig. 30 · DIN-Rail Mounting
1. Use the screws to screw the DIN-Rail on the rear side of the industrial switch. 2. To remove the DIN-Rail, reverse the step 1. 3. After the DIN-Rail is screwed on the rear side of the switch, insert the top of DIN-Rail into the track.
Page 15 of the LevelOne IFE-0502 user manual — Mounting Installation
Page 15 · click to enlarge
Page 15
LevelOne IFE-0502 — Mounting Installation diagram (page 15)
Fig. 31 · Mounting Installation
4. Then, lightly push the DIN-Rail into the track.
LevelOne IFE-0502 — Mounting Installation diagram (page 15)
Fig. 32 · Mounting Installation
5. Check if the DIN-Rail is tightened on the track or not. 6. To remove the industrial switch from the track, reverse steps above.
Page 16 of the LevelOne IFE-0502 user manual — Wall Mount Plate Mounting
Page 16 · click to enlarge
Page 16

Wall Mount Plate Mounting

1. Follow the steps below to mount the industrial switch with wall mount plate. 2. Remove the DIN-Rail from the industrial switch; loose the screws to remove the DIN-Rail. 3. Place the wall mount plate on the rear panel of the industrial switch. 4. Use the screws to screw the wall mount plate on the industrial switch. 5. Use the hook holes at the corners of the wall mount plate to hang the industrial switch on the wall. 6. To remove the wall mount plate, reverse steps above.

LevelOne IFE-0502 — Wall Mount Plate Mounting diagram (page 16)
Fig. 33 · Wall Mount Plate Mounting
LevelOne IFE-0502 — Wall Mount Plate Mounting diagram (page 16)
Fig. 34 · Wall Mount Plate Mounting
LevelOne IFE-0502 — Wall Mount Plate Mounting diagram (page 16)
Fig. 35 · Wall Mount Plate Mounting

Screw the wall mount plates on the Industrial Switch

Page 17 of the LevelOne IFE-0502 user manual — Installation Steps
Page 17 · click to enlarge
Page 17

Hardware Installation

In this paragraph, we are going to mention how to install the 4-Port PoE + 1-Port SC Industrial Fast Ethernet Switch and the installation points to be attended to it.

Installation Steps

1. Unpack the Industrial switch packing. 2. Check if the DIN-Rail is screwed on the Industrial switch or not. If the DIN-Rail is not screwed on the Industrial switch, please refer to DIN-Rail Mounting section for DIN-Rail installation. If user want to wall mount the Industrial switch, then please refer to Wall Mount Plate Mounting section for wall mount plate installation. 3. To hang the Industrial switch on the DIN-Rail track or wall, please refer to the Mounting Installation section. 4. Power on the Industrial switch. Please refer to the Wiring the Power Inputs section for knowing the information about how to wire the power. The power LED on the Industrial switch will light up. Please refer to the LED Indicators section for indication of LED lights. 5. Prepare the twisted-pair, straight through Category 5e/above cable for Ethernet connection. 6. Insert one side of the RJ-45 cable into the Industrial switch Ethernet port and another side to the network device’s Ethernet port, e.g. Switch, PC or Server. The UTP/STP port (RJ-45) LED on the Industrial switch will light up when the cable is connected with the network device. Please refer to the LED Indicators section for LED light indication. 7. When all connections are set and LED lights all show in normal, the installation is complete.

Page 18 of the LevelOne IFE-0502 user manual — Network Application
Page 18 · click to enlarge
Page 18

Network Application

This segment provides the sample to help user have more actual idea of industrial switch application. For a sample application of the industrial switch, see the figure below.

LevelOne IFE-0502 — Network Application diagram (page 18)
Fig. 36 · Network Application
Page 19 of the LevelOne IFE-0502 user manual — Troubleshooting
Page 19 · click to enlarge
Page 19

Troubleshooting

„ Verify that is using the right power cord/adapter (DC 48V), please don’t use the power adapter with DC output voltage higher than 48V, or it will burn this equipment down. „ Select the proper UTP/STP cable to construct your network. Please check that is using the right cable. Use unshielded twisted-pair (UTP) or shield twisted-pair ( STP ) cable for RJ-45 connections: 100Ω Category 3, 4 or 5 cable for 10Mbps connections, 100Ω Category 5 cable for 100Mbps connections, or 100Ω

Category 5e/above cable for 1000Mbps. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet). „ Diagnosing LED Indicators: the Switch can be easily monitored through panel indicators, which describes common problems user may encounter and where user can find possible solutions, to assist in identifying problems. „ If the power indicator does not light on when the power cord is plugged in, user may have a problem with power cord. Then check for loose power connections, power losses or surges at power outlet. If you still cannot resolve the problem, contact the local dealer for assistance. „ If the Industrial switch LED indicators are normal and the connected cables are correct but the packets still cannot transmit. Please check your system’s Ethernet device’s configuration or status.

Page 20 of the LevelOne IFE-0502 user manual — LED
Page 20 · click to enlarge
Page 20

Technical Specification

The IFE-0501/IFE-0502 4-Port PoE + 1-Port SC Industrial Fast Ethernet Switch technical specifications are shown as below.

IFE-0501 4-Port PoE + 1-Port Multi-mode SC Industrial Fast Ethernet Switch IFE-0502 4-Port PoE + 1-Port Single-mode SC Industrial Fast Ethernet Switch

IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX/FX Fast Ethernet

IEEE802.3x Flow Control and Back Pressure IEEE802.3af Power over Ethernet

Transfer Rate 14,880 pps for 10Base-T Ethernet port 148,800 pps for 100Base-TX/FX Fast Ethernet port

MAC Address 1K MAC address table

Per unit: Power 1 (Green), Power 2 (Green), Fault(Red) Fiber: Link/Active(Green) TX: Link/Active(Green), Full duplex/Collision (Yellow) PoE: Feeding Power (Green)

LED

10Base-T: 2-pair UTP/STP Cat. 3, 4, 5, 5e cable EIA/TIA-568 100-ohm (100m) 100Base-TX: 2-pair UTP/STP Cat. 5/5e cable EIA/TIA-568 100-ohm (100m)

Standard · Protocol CSMA/CD · Network Cable

Page 21 of the LevelOne IFE-0502 user manual — Technical Specification
Page 21 · click to enlarge
Page 21
LevelOne IFE-0502 — Technical Specification diagram (page 21)
Fig. 37 · Technical Specification

Distance: Multi mode: 50/125μm ~ 62.5/125μm Single mode: 9/125μm Available distance: 2km (multi-mode)/30km (single-mode) Wavelength: 1310nm (Multi-mode/Single-mode)

Power Supply Redundant power DC 48V with removable terminal block 12VDC (without PoE); 48VDC (Full load with PoE)

Power Consumption 4.6Watts (without PoE); 58Watts (Full load with PoE)

Installation DIN rail kit for DIN-type cabinet install and wall-mount ear for wall mounting

Operating Temp. -10℃ to 60℃ (14℉ ~ 140℉)

Case Dimension IP-30, 30 mm (W) x 95 mm (D) x 140mm (H)

FCC Class A CE EN61000-4-2/3/4/5/6/8/11/12 CE EN61000-6-2 CE EN61000-6-4

Ask about the LevelOne IFE-0502

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LevelOne IFE-0502

Be the first to ask — other owners or our team will answer.

Original document

LevelOne IFE-0502 manual PDF

21 pages·522 KB·Switch·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…