Instruction/ maintenance manual of the product Scandium-NG Lennox Hearth
Go to page of 28
INST ALLA TION AND OPERA TION INSTRUCTIONS Catalytic V ent - Free W all-Mounted Fireplace Model: Scandium-NG P/N 850,055M Rev . NC, 04/2007 Installer: Leave This Manual With The Appliance.
2 This appliance is a high efficiency , unvented, flame ef fect gas heater. It provides radiant and convected warmth both efficiently and safely utilizing the latest type catalytic convertor burner technology .
• Children and adults should be alerted to the hazard of high surface temperature and should stay away to avoid burns or clothing ignition. • Y oung children should be carefully supervised when they are in the same room with the heater . • Do not place clothing or other flammable material on or near the heater .
Example: V ent-free heater #1 9,000 BTU/Hr V ent-free heater #2 23,000 BTU/Hr Gas appliance #1 35,000 BTU/Hr (water heater) T otal = 67,000 BTU/Hr * Do not include direct-vent gas appliances. Direct-vent is sealed combustion and draws combustion air from the outdoors.
Clearances to non-combustibles Non-combustible surfaces are defined as brick, metal, marble, concrete etc. and also a number of man-made materials impervious to flame. If in doubt refer to the material manufacturer for further information before proceeding with installation.
There are no imitation fuel bed components to install. The appliance features a ribbon burner which is designed to produce a continuous band of flame over its length. The burner should be visually inspected to ensure it is free from any foreign matter .
The pressure test points are located as shown in figure 7. An alternative burner (mainfold test point is located below the left hand side of the burner as shown in figure 8. The pressure regulator on manual models is preset and locked to avoid tampering.
8 2. Slide on the side pieces ensuring that the grille fixing holes (shown) are aligned towards the top of the glass facia (as shown in figure 1 1). 3.Ensure the sides are neatly aligned with the glass and secure the sides using two M6 screws for each side as shown in figure 12.
9 Insert a screwdriver through the holes in the right hand side panel to access the two M6 fixing screws (designated ‘a’ in figure 17) and tighten fully . Next insert two no.8 self tapping screws (designated ‘b’ in figure 17) through the side panel support bracket, and the corresponding holes in the side of the firebox.
Remove the glass facia, glass panel and burner unit (as per servicing section), lint arrestor and pilot unit by using a screwdriver to remove the retaining screws. Clean the pilot assembly with a soft brush and blow through. Check the aeration holes are free of any dirt or lint.
11 FOR YOUR SAFETY READ BEFORE LIGHTING A. This heater has a pilot which must be lit by hand. When lighting the pilot, follow these instructions exactly . B. BEFORE OPERA TING smell all around the heater area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor .
12 Fire sparks but pilot does not light No gas to Pilot, check the gas line connections. Air not fully purged, repurge supply or wait longer . Spark grounding to metal work, reset gap correctly . Blocked pilot, clean out internally . Pilot lights but then goes out Severe restriction in gas supply: clear obstruction.
13 Figure 22 Figure 21: Removal and refitting of glass door assembly and burner assembly . Figure 22 : V isual check for correct pilot flame. 29.0 POSITIONING OF FIELD REMOV ABLE P ARTS Figure 21 4 of.
1 110 W est T aft A venue • Orange, CA 92865 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE Lennox reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
INSTRUCCIONES DE INST ALACIÓN Y OPERACIÓN Chimenea catalítica de pared sin salida de humos Modelo : Scandium-NG P/N 850,055M Rev . NC, 04/2007 Instalador: Deje este manual junto al aparato. Consumidor: Guarde este manual para su consulta en el futuro.
16 Este aparato es un calentador de gas de alta eficacia, sin salida de humos, con efecto de llama. Proporciona calor por radiación y por convección de manera eficiente y segura, utilizando las últimas tecnologías de combustión con conversión catalítica.
• Es necesario advertir a niños y adultos del peligro de la alta temperatura de la superficie, y éstos deben mantenerse alejados para evitar quemaduras o que se les prenda fuego la ropa. • Es necesario supervisar cuidadosamente a los niños pequeños cuando estén en la misma habitación que el calentador .
Ejemplo: Calentador sin salida de humos N° 1 9.000 BTU/h Calentador sin salida de humos N° 2 23,000 BTU/h Aparato de gas Nº 1 35.000 BTU/h (calentador de agua) T otal = 67.000 BTU/h * No incluya aparatos de gas con salida de humos directa. La salida de humos directa tiene combustión sellada y aspira el aire de combustión desde fuera.
Espacio libre hasta superficies no combustibles Las superficies no combustibles se definen como ladrillo, metal, mármol, hormigón etc., así como diversos materiales artificiales que son insensibles a las llamas. En caso de duda, solicite más información al fabricante del material antes de proceder con la instalación.
No hay componentes de lecho de combustible de imitación que instalar . El aparato tiene un quemador tipo cinta que ha sido diseñado para producir una banda continua de llamas en toda su longitud. Inspeccione visualmente el quemador para asegurarse de que está libre de elementos extraños.
Los puntos de prueba de presión están ubicados en los lugares indicados en la Figura 7. Un punto de prueba alternativo del quemador (colector) está ubicado debajo del lateral izquierdo del quemador , según muestra la Figura 8. El regulador de presión de los modelos manuales está preajustado y bloqueado para evitar su manipulación indebida.
22 2. Deslícelo por las piezas laterales y asegúrese de que los orificios de fijación de la rejilla (que se ilustran) queden alineados hacia la parte superior del panel decorativo de vidrio (según se muestra en la figura 1 1).
23 Introduzca un destornillador a través de los orificios del panel de la derecha y apriete los dos tornillos de fijación M6 (tornillos ‘a’ en la figura 17).
Retire el panel decorativo de vidrio, la puerta de vidrio y el conjunto del quemador (según lo indicado en la sección de mantenimiento), el filtro de malla y el conjunto del piloto usando un destornillador para retirar los tornillos de fijación. Limpie el conjunto del piloto con un cepillo suave y sople a través del mismo.
25 P ARA SU SEGURIDAD, LEA ANTES DE ENCENDER EL AP ARA TO A. El calentador tiene un piloto que debe ser encendido manualmente. Para encender el piloto, siga estas instrucciones exactamente. B. ANTES DEL USO examine toda la zona del calentador y verifique si hay olor a gas.
26 Se produce una chispa pero el piloto no se No llega gas al piloto, compruebe las conexiones de la tubería de gas. enciende El aire no se ha purgado del todo: vuelva a purgar el aire, o espere más tiempo. Derivación de la chispa a una pieza metálica: ajuste correctamente el espacio entre electrodos.
27 Figura 22 Figura 21: Remoción y reinstalación del conjunto de la puerta de vidrio y del conjunto del quemador . Figura 22: Comprobación visual de la llama del piloto.
14 1 110 W est T aft A venue • Orange, CA 92865 NOT A: LOS DIAGRAMAS Y LAS ILUSTRACIONES NO ESTÁN A ESCALA Lennox se reserva el derecho de modificar , en cualquier momento y sin previo aviso el diseño, los materiales, las especificaciones y los precios, así como también discontinuar colores, estilos y productos.
An important point after buying a device Lennox Hearth Scandium-NG (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lennox Hearth Scandium-NG yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lennox Hearth Scandium-NG - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lennox Hearth Scandium-NG you will learn all the available features of the product, as well as information on its operation. The information that you get Lennox Hearth Scandium-NG will certainly help you make a decision on the purchase.
If you already are a holder of Lennox Hearth Scandium-NG, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lennox Hearth Scandium-NG.
However, one of the most important roles played by the user manual is to help in solving problems with Lennox Hearth Scandium-NG. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lennox Hearth Scandium-NG along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
