


This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine.
For safe and correct use of this machine, please be sure to read the Safety Information in the General Settings Guide before you use it.
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Use of controls or adjustment or performance of procedures other than those specified in this manual might result in hazardous radiation exposure.
The model names of the machines do not appear in the following pages. Check the type of your ma- chine before reading this manual. (For details, see p.2 “Machine Types”.)
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the metric version.
For good copy quality, Rex-Rotary recommends that you use genuine Rex-Rotary toner.
Rex-Rotary shall not be responsible for any damage or expense that might result from the use of parts other than genuine Rex-Rotary parts in your Rex-Rotary office product.
Please be sure to connect the power cord to a power source as above. For details about power source, see “Power Connection” in the General Settings Guide.
For safety, please read this manual carefully before you use this product and keep it handy for future reference.
Introduction · Power Source

This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine.
For safe and correct use of this machine, please be sure to read the Safety Information in the General Settings Guide before you use it.
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Use of controls or adjustment or performance of procedures other than those specified in this manual might result in hazardous radiation exposure.
The model names of the machines do not appear in the following pages. Check the type of your ma- chine before reading this manual. (For details, see p.2 “Machine Types”.)
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the metric version.
For good copy quality, Gestetner recommends that you use genuine Gestetner toner.
Gestetner shall not be responsible for any damage or expense that might result from the use of parts other than genuine Gestetner parts in your Gestetner office product.
Please be sure to connect the power cord to a power source as above. For details about power source, see “Power Connection” in the General Settings Guide.
For safety, please read this manual carefully before you use this product and keep it handy for future reference.
Introduction · Power Source

This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine.
For safe and correct use of this machine, please be sure to read the Safety Information in the General Settings Guide before you use it.
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Use of controls or adjustment or performance of procedures other than those specified in this manual might result in hazardous radiation exposure.
The model names of the machines do not appear in the following pages. Check the type of your ma- chine before reading this manual. (For details, see p.2 “Machine Types”.)
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the metric version.
For good copy quality, Nashuatec recommends that you use genuine Nashuatec toner.
Nashuatec shall not be responsible for any damage or expense that might result from the use of parts other than genuine Nashuatec parts in your Nashuatec office product.
Please be sure to connect the power cord to a power source as above. For details about power source, see “Power Connection” in the General Settings Guide.
For safety, please read this manual carefully before you use this product and keep it handy for future reference.
Introduction · Power Source

“The Product complies with the requirements of the EMC Directive 89/336/EEC and its amending di- rectives and the Low Voltage Directive 73/23/EEC and its amending directives.”
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
c means STAND BY.
Acrobat® is a registered trademark of Adobe Systems Incorporated.
Declaration of Conformity · Trademark · Copyright © 2002

AdonisC3copy_gb_Cover2-5 Page 1 Friday, January 24, 2003 1:26 PM
This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine.
For safe and correct use of this machine, please be sure to read the Safety Information in the General Settings Guide before you use it.
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Use of controls or adjustment or performance of procedures other than those specified in this manual might result in hazardous radiation exposure.
The model names of the machines do not appear in the following pages. Check the type of your ma- chine before reading this manual. (For details, see p.2 “Machine Types”.)
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the metric version.
For good copy quality,Infotec recommends that you use genuine Infotec toner.
Infotec shall not be responsible for any damage or expense that might result from the use of parts other than genuine Infotec parts in your Infotec office product.
Please be sure to connect the power cord to a power source as above. For details about power source, see “Power Connection” in the General Settings Guide.
This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses.
It should not therefore be construed as guaranteeing specific properties of the products described or their suitability for particular applications.
Any existing industrial property rights must be observed. The quality of our products is guaranteed un- der our General Conditions of Sale.
For safety, please read this manual carefully before you use this product and keep it handy for future reference.
Introduction · Power Source

“The Product complies with the requirements of the EMC Directive 89/336/EEC and its amending di- rectives and the Low Voltage Directive 73/23/EEC and its amending directives.”
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
c means STAND BY.
Acrobat® is a registered trademark of Adobe Systems Incorporated.
Declaration of Conformity · Trademark · Copyright © 2002

AdonisC3_GBcopyF_FM1.book Page i Thursday, November 28, 2002 1:53 PM
The following manuals describe the operational procedures of this machine. For particular functions, see the relevant parts of the manual.
❖General Settings Guide
Provides an overview of the machine. It also describes System Settings (such as paper trays and user codes settings), Document Server functions, and troubleshooting.
❖Network Guide (PDF file - CD-ROM1)
Describes procedures for configuring the machine and computers in a net- work environment.
❖Copy Reference (this manual)
Describes operations, functions, and troubleshooting for the machine's copier function.
❖Facsimile Reference <Basic Features>
Describes operations, functions, and troubleshooting for the machine's fac- simile function.
❖Facsimile Reference <Advanced Features>
Describes advanced functions and settings for key operators.
❖Printer Reference 1
Describes system settings and operations for the machine's printer function.
❖Printer Reference 2 (PDF file - CD-ROM1)
Describes operations, functions, and troubleshooting for the machine's print- er function.
❖Scanner Reference (PDF file - CD-ROM1)
Describes operations, functions, and troubleshooting for the machine's scan- ner function.

AdonisC3_GBcopyF_FM1.book Page ii Thursday, November 28, 2002 1:53 PM
❖Manuals for DeskTopBinder V2 Lite
❖Manuals for ScanRouter V2 Lite
❖Other manuals

AdonisC3_GBcopyF_FM1.book Page iii Thursday, November 28, 2002 1:53 PM
1-sided 2 Pages 2-sided 1 Page (see p.43 " 1 Sided 2 Sided")
2-sided 1 Page 2-sided 1 Page (see p.43 " 2 Sided 2 Sided")
1-sided 4 Pages 2-sided 1 Page (see p.47 " 1 Sided 4 Pages Combine 2 Side")
2-sided 2 Pages 2-sided 1 Page (see p.47 " 2 Sided 4 Pages Combine 2 Side")
2-sided 4 Pages 2-sided 1 Page (see p.47 " 2 Sided 8 Pages Combine 2 Side") 1-sided 8 Pages 2-sided 1 Page (see p.47 " 1 Sided 8 Pages Combine 2 Side")
1-sided 16 Pages 2-sided 1 Page (see p.47 " 1 Sided 16 Pages Combine 2 Side")
2-sided 8 Pages 2-sided 1 Page (see p.48 " 2 Sided 16 Pages Combine 2 Side")
Front/Back Bound Originals 2-sided Pages (see p.49 " Front & Back 2 Sided") Bound Originals 2-sided Pages (see p.49 " Book 2 Sided")

AdonisC3_GBcopyF_FM1.book Page iv Thursday, November 28, 2002 1:53 PM

1-sided 4 Pages Booklet (see p.50 " 1 Sided Booklet")
2-sided 2 Pages Booklet (see p.51 " 2 Sided Booklet")

AdonisC3_GBcopyF_FM1.book Page v Thursday, November 28, 2002 1:53 PM

Combining Multiple Pages onto a Single Page (see p.45 " One-Sided Combine")
1-sided 2 Pages 1-sided 1 Page 2-sided 1 Page 1-sided 1 Page
1-sided 4 Pages 1-sided 1 Page 2-sided 2 Pages 1-sided 1 Page
Copying Originals Such as Books (see p.49 "Series Copies")
Copying 2-Sided Pages onto 1-Sided Pages (see p.43 "2 Sided 1 Sided")





AdonisC3_GBcopyF_FM1.book Page viii Thursday, November 28, 2002 1:53 PM

In this manual, the following symbols are used:
R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the in- structions under this symbol. Be sure to read the instructions, all of which are in- cluded in the Safety Information section in the General Settings Guide.
R CAUTION: This symbol indicates a potentially hazardous situation that might result in mi- nor or moderate injury or property damage that does not involve personal injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section in the General Settings Guide. • WARNINGS and CAUTIONS are notes for your safety.
Preparation This symbol indicates prior knowledge or preparations are required before op- eration.
Limitation This symbol indicates numerical limits, functions that cannot be used together, or conditions in which a particular function cannot be used.

[ ] Keys that appear on the machine's display panel.
{ } Keys built into the machine's control panel.

This machine comes in two models which vary by copy speed. To make sure which model you have, see the inside front cover of this manual.
Type 1 Type 2
Copy speed 35 copies/minute (A4K, 81/2" × 11"K)
45 copies/minute (A4K, 81/2" × 11"K)

The available functions depend on your machine configuration and which op- tions you have. See the table below. ❍Required options

*1 The bridge unit and paper tray unit are required when you install the finisher.

stalled.

5. {Check Modes} key Press to check the entered copy job set- tings. 6. {Program} key Press to select the program mode. See p.74 “Programs”. 7. {Clear Modes} key Press to clear the previously entered copy job settings. 8. {Energy Saver} key Press to switch to and from the Energy Saver mode. See General Settings Guide. 9. {Interrupt} key Press to interrupt a long copy job to make copies. See p.16 “Interrupt Copy” . 10. Main power indicator The main power indicator goes on when you turn on the main power. The power indicator lights when the power is on.
switch while the power indicator goes on or is flashing. The hard disk may malfunction.

11. Operation switch Press this switch to turn the power on (the On indicator goes on). To turn the power off, press this switch again (the On indicator goes off). 12. {Sample Copy} key Use this key to make a single sample copy before starting a long copy run. By checking the sample copy and making any necessary changes to the image qual- ity settings before you make multiple copies, you can save time and paper. See p.33 “Sample copy”. 13. {Start} key Press to start copying. Press to start scan- ning and printing in Document Server mode. 14. {Clear/Stop} key

Tray finisher and large capacity tray (LCT) installed.
❖Initial copy display



A3L – B6 JIS (Japanese Industri- al Standard) KL
11" × 17"L – 51/2" × 81/2"KL
11" × 17"L – 51/2" × 81/2"KL
about 80. ❒The weight range for originals in the Mixed Size mode is 52–81 g/m2, 13.8–

tool.

81/2" × 13" L *1 Location of the original
11" × 17"L 81/2" × 14" L
51/2" × 81/2" KL
Exposure glass ❍ × ❍ × ❍
❍ *2 ❍ × ❍ × ❍
*1 You can select from 81/2" × 13", 81/4" × 13", 8" × 13" with User Tools (System Settings). See “Size Setting ”in “General Features”, General Settings Guide. *2 The machine cannot detect two-sided originals of B6 JIS size. ❍ : Detectable size × : Undetectable size

11" × 17"L 81/2" × 14" L
51/2" × 81/2" KL
Exposure glass × ❍ ❍ ❍ × × ×
❍ × ❍ × × ❍ × ❍
Placing Originals · ❖Metric version · ❖Inch version


❖Auto Document Feeder

originals. If not, the image may not be copied properly. See p.14 “Placing cus- tom size originals”.
Even if you correctly place originals in the ADF or on the exposure glass, 3 mm (0.1”) margins on all four sides might not be copied.
Originals · ❖Exposure glass

For example, to copy A3Kor 11" × 17"K originals with the Staple function selected:
id and ink have completely dried. Not taking this precaution could dirty the exposure glass with marks that will be copied.

Reference For original sizes you can set, see p.7 “Originals” .
You can set the original orientation in the following ways. This function is useful for copying torn originals or large originals.
Select this function when the origi- nal orientation is the same as the copy paper orientation.
Use this function when you want to copy A3K, B4 JISKor 11" × 17"K size originals. The machine rotates the copy image by 90° and you can make copies as you want. This is useful for copying large originals with the Staple, Duplex, Combine or Stamp functions.
tion together with the Auto Paper Select or the Preset Reduce/En- large function. A Press [Special Original].

Placing Originals

B Select the original orientation.
A Lift the exposure glass cover or
A Make sure that is select- ed.
the ADF.

cover or the ADF forcefully. Otherwise, the cover of the ADF might open or be damaged.
cover or the ADF by more than 30°. Otherwise, the size of the original might not be detected correctly. B Place the original face down on
A Place your original in the land-

the exposure glass. The original should be aligned to the rear left corner.
the ADF.
Placing Originals · Standard orientation

original size. B Align the edges of the original
Settings should be made in the fol- lowing situations:
and place it on the ADF with the side to be copied facing up.

❖When placing originals one by one:
p.13 “SADF mode”
❖When placing originals consisting of
❖When copying originals of various
❖When placing custom size originals:
p.14 “Placing custom size origi- nals”
before placing it on the ADF. ❒To prevent multiple sheets from
limit mark on the side fence of the ADF. ❒The last page should be on the bot-
being fed at once, fan the origi- nal before placing it on the ADF. ❒Set the original squarely.
tom. ❒Do not place objects on the sensors
or cover them with your hands. This could cause the size to be de- tected incorrectly. Also, do not place anything on the exposure glass cover as this could cause a malfunction.
In Batch mode, the machine copies an original including more than 80 pages as one document, even if it is placed on the ADF in parts. A Press [Special Original].


Placing Originals

B Select [Batch], and then press [OK].
B Press [SADF], and then press [OK]. C Place one page of an original, and
then press the {Start} key. The Auto Feed indicator is shown on the display. D When the machine instructs you
change the settings. See p.101 “Switch to Batch (SADF)”. C Place the first part of the original,
and then press the {Start} key. D After the first part of the original
to place another original, place the next page. The second and subsequent pages will be fed automatically without pressing the {Start} key.
has been fed, place the next part. E When the Sort, Combine or 1 Sid-
ed → 2 Sided mode has been set, press the {#} key after all origi- nals have been scanned. F Press the {Start} key.
When placing different size originals of the same width in the ADF at the same time, the machine automatically checks the size of the originals and makes copies.

In SADF mode, even when an origi- nal is placed page by page in the ADF, each page is automatically fed when placed.
sizes in the ADF and making cop- ies without using the Mixed Size mode, parts of the original image might not be copied or paper might become jammed. ❒Copy speed and scanning speed
Preparation To use the SADF function, you should make a setting in User Tools (Copier/Document Server Features), so that [SADF] will be displayed when you press [Special Original]. See p.101 “Switch to Batch (SADF)”.
may be reduced. ❒You can place originals of two dif-
ferent sizes at a time. ❒The sizes of the originals that can
Reference Related default settings, see p.94 “Shortcut R/E”. A Press [Special Original].
be placed together using this func- tion are as follows:

A3L, B4 JIS L, A4KL, B5 JISKL
11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2" KL
Placing Originals

![Lanier LD045 — B Press [ Mixed Size ] , and then press diagram (page 29)](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/fig-29-1.webp)
B Press [Custm Size Origi.]. C Enter the horizontal size of the
original with the number keys, and then press [#].
the originals as shown.
[Clear] or the {Clear/Stop} key, and then enter the value again. D Enter the vertical size of the origi-
nal with the number keys, and then press [#]. E Press [OK].
up into the ADF. F Press the {Start} key.
When placing custom size originals in the ADF, specify the size of the origi- nals.
128–297 mm (5"–11") and a hori- zontal length of 128–1,260 mm (5"– 49") can be placed with this func- tion.
Placing Originals

Basic Procedure
A When the machine is set for user
E Set your desired settings.
codes, enter a user code (up to 8 digits) with the number keys, and then press the {#} key. The machine is ready to copy.
Reference Please refer to each function. F Enter the required number of cop-
ies with the number keys.
Reference For users codes, see “Key Oper- ator Tools”, General Settings Guide. B Make sure that "dReady" is
that can be set is 999. G Press the {Start} key.
shown on the display. If any other function is displayed, press the {Copy} key.
The machine starts copying.
❖Initial copy display
exposure glass, press the {#} key after all originals are scanned. ❒Copies are delivered face down.

-How to operate
❖To stop the machine during a multi-
copy run. Press the {Clear/Stop} key.
ous settings remaining.
❖To return the machine to the initial
condition after copying. Press the {Clear Modes} key.
tings remaining, press the {Re- set} key and enter again. D Place your originals.
❖When clearing entered values.
Press the {Clear/Stop} key or [Clear] on the display.
Reference p.10 “Placing Originals”
❖To check the settings.
Press the {Check Modes} key.

When the machine keeps copying
A Place the originals you want to
Use this function if you want to inter- rupt a long copy job to make urgently needed copies.
copy. B Press the {Start} key.
Limitation ❒You cannot use the Interrupt Copy
The machine stops the previous original job and starts copying the original. C When copying is complete, re-
function when fax originals are be- ing scanned or the scanner func- tion is being used. A Press the {Interrupt} key.
move originals and copies. D Press the {Interrupt} key again.
The Interrupt indicator goes off. The interrupt copy job settings will be restored and the ma- chine will continue copying from where it left off.
The Interrupt indicator goes on.
When the originals stop scanning
A Remove the originals that were
being copied and place the originals you want to copy. B Press the {Start} key.
The beeper sounds and an error mes- sage is displayed when you leave your originals on the exposure glass after copying.
The machine starts making the copies. C When copying is complete, re-
move the originals and copies. D Press the {Interrupt} key again.
The Interrupt indicator goes off. E When the display prompts
you, place the remaining origi- nals again before interrupting. F Press the {Start} key.
tings will be restored and the machine will continue copy- ing from where it left off.
Copying

You can set up the next copy content during copying. If a long copy job is in progress and you do not want to wait for it to fin- ish, you can use this function to set up the next copy job in advance. When the current copy job is finished, the next job will start automatically. A Press [Next Job] when "Copying" is
shown.

B Set up the next copy job. C Place the originals in the ADF,
and then press the {Start} key. All originals are scanned. D Press [To "Printing"].
Returns to the initial copy display. After the current copy job, the next job starts automatically.
the current copy job by pressing [To "Printing"]. You can switch the display to the preset job by pressing [To "Reserving"].
Basic Procedure

Use the bypass tray to copy onto OHP transparencies, adhesive labels, trans- lucent paper, postcards and copy pa- per that cannot be loaded in the paper trays.
A3L, A4KL, A5KL, 81/2" × 13"L
A3L, 11" × 17"L, 81/2" × 11"KL, 51/2" × 81/2"L
❒When copying on OHP transpar-
Preparation When the duplex unit is attached, the default is [1 Sided → 2 Sided]. When copying from the bypass tray, select [1 Sided] for copying in [Dup./Combine/Series] (for example [1 Sided → 1 Sided] or [2 Sided → 1 Sided] ). You can change the initial settings. See p.92 “Duplex Mode Priority” .
encies or paper heavier than 128 g/m2 (about 34 lb.), you need to specify the paper type. See p.19 “When copying onto special pa- per” . ❒The maximum number of sheets
you can load at the same time de- pends on paper type. The maxi- mum number of sheets should not exceed the upper limit. A Open the bypass tray.

size is used, the paper may become wrinkled, may not be fed into the machine, or may cause paper jams.
copy paper or if you use special pa- per, you should input vertical and horizontal dimensions. See p.14 “Placing custom size originals”. The sizes that you can input are as follows:
want to copy facing down until you hear the beep, and then align the paper guide to the paper size.

*1 The range is 148-432 mm (5.8"-17") when the booklet finisher is in- stalled. ❒The machine can automatically de-
tect the following sizes as standard size copy paper:

Copying from the Bypass Tray

the copy paper, images might be skewed or paper misfeeds might occur. ❒Do not stack paper over the lim-
it mark, otherwise images might be skewed or paper mis- feeds might occur. ❒Swing out the extender to sup-
C Press [Vertical mm], enter the
port paper sizes larger than A4L, 81/2" × 11"L. ❒Fan paper to get air between the
vertical size with the number keys, and then press the [#] key. D Enter the horizontal size of the
sheets and avoid a multi-sheet feed. C Select the type and size of the pa-
paper with the number keys, and then press the [#] key.
per.
ed, press [Horiz mm]. ❒To register the custom size

entered, press [Program], and then press [Exit].
A Press the {#} key. B Press [Select Size].
C Select the paper size. D Press [OK].
When copying onto special paper
A Press the {#} key. B Select paper type in Special pa-
When copying onto custom size paper
per. C Press [OK].
livered to the internal tray. A Press the {#} key.

press the {Start} key.
parencies, remove copied sheets one by one. E When your copy job is finished,
press the {Clear Modes} key to clear the settings.
Copying
![Page 36 of the Lanier LD045 user manual — A Make sure that [ Auto Image Density ]](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/page-36.webp?w=400)
There are three types of adjustment available:
it. B Press [ Lighter ] or [ Darker ] to adjust
❖Auto Image Density
The machine automatically adjusts image density.
the image density.
![Lanier LD045 — A Press [ Auto Image Density ] to cancel diagram (page 36)](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/fig-36-1.webp)
You can adjust the density of the overall original in seven incre- ments.
density Use when copying originals with a dirty background (such as news- papers). You can adjust fore- ground density while leaving the background unchanged.
is selected. B Press [Lighter] or [Darker] to adjust
Copier Functions · Manual image density

the original type.

Select one of the following six types to match your originals:
Select this mode when your origi- nals contain only text (no pictures).
Select [Text/Photo] when your origi- nals contain photographs or pic- tures with text.
When the original type keys are not displayed
A Press [Original Type]. B Select the original type, and
Delicate tones of photographs and pictures can be reproduced with this mode.
then press [OK].
Select this mode for originals that have lighter lines in pencil, or for faint copied slips. The faint lines will be clearly copied.
If your originals are copies (gener- ation copies), the copy image can be reproduced sharply and clearly.
Reference p.90 “Original Type Display” p.91 “Copy Quality”

There are two ways to select copy paper:
❖Auto Paper Select
The machine selects a suitable size of copy paper automatically based on orig- inal size and reproduction ratio.
❖Manual Paper Select
Choose the tray containing the paper you want to copy onto: a paper tray, by- pass tray or Large Capacity Tray (LCT).
Reference p.9 “Sizes difficult to detect” p.90 “Paper Display”
with Auto Paper Select (when copying at a ratio of 100%).

Exposure glass A3L, B4 JISL, A4KL, B5 JISKL
Auto Document Feeder A3L, B4 JISL, A4KL, B5 JISKL, A5KL, B6 JISKL, 11”× 17”L, 81/2" × 11"KL

Exposure glass 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL
Auto Document Feeder A3L, A4KL, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2"KL, 10" × 14"L
❒Only the paper trays set to [No display] or [Recycled paper] in Paper Type and
also set to [Yes] in Apply Auto Paper Select can be selected in Auto Paper Se- lect mode. See “Paper Type: Tray 1–4”in "Tray Paper Settings", General Set- tings Guide.
Copier Functions · ❖Metric version · ❖Inch version


A Make sure that [Auto Paper Select] is selected.
Type”in “Tray Paper Settings", General Settings Guide.
A Select the paper tray, bypass tray or the LCT.
The indicator corresponding to the selected paper tray is highlighted.

When the paper type keys are not displayed
A Press [Auto Paper Select]. B Select the paper type.
Copying · Manual Paper Select

If the orientation in which your original is placed (L or K) is different from that of the paper you are copying onto, this function rotates the original image by 90° to fit it on the copy paper. This function works when Auto Paper Select or Auto Reduce/Enlarge is selected. See p.23 “Auto Paper Select”.

the Rotated Copy function if this setting is changed to Without image rotation or Off. See p.90 “Auto Tray Switching”. ❒You cannot use the Rotated Copy function when enlarging onto A3, B4 JIS or
11" × 17", 81/2" × 14" size paper. In this case, place your original in the L ori- entation.

❒You cannot use the Rotated Copy function when” Left 2" or "Top 2” is select-
ed for stapling or if the Punch function is selected when using the 2 Tray fin- isher. See p.35 “Staple” and p.41 “Punch”. ❒You cannot use the Rotate Copy function if ”Left 2”, “Top 2”or “Saddle
Stitch”is selected for the stapling when using the booklet finisher.
Copier Functions · -Rotated copy


itial display, press the shortcut reduce/enlarge key and pro- ceed to step D. B Press [Enlarge] or [Reduce]. C Select a ratio, and then press [OK]. D Place your originals, and then
The base point of Reduce/Enlarge differs depending on how the orig- inal is scanned. When the original is placed on the exposure glass, the upper left corner will be the base point. When it is placed in the ADF, the bottom left corner will be the base point.
press the {Start} key.

-Create margin mode
Use Create Margin to reduce the im- age to 93% of its original size with the centre as reference. You can assign this function to a shortcut key on the initial display. By combining it with the Reduce/Enlarge function, you can also provide the Reduce/Enlarge copy with a margin.
Reference Related initial settings p.93 “Copy Function Key: F1-F5” p.95 “Ratio for Create Margin”
Reference Related initial settings p.94 “Shortcut R/E” p.95 “R/E Priority”
Copying · ❖Base Point

A Press [Create Margin] displayed on
B Enter the ratio.
the initial display.

To select the ratio with [n] and [o]
A Select a preset ratio close to the
desired ratio by using [Reduce] or [Enlarge]. B Adjust the ratio with [n] or
[o].
B If you do not want to combine it
with the Reduce/Enlarge function, place your originals, and then press the {Start} key.
ments of 1%, press [n] or [o]. To change the ratio in 10% steps, press and hold down [n] or [o]. ❒If you have incorrectly en-
tered the ratio, readjust with [n] or [o].
You can change the reproduction ra- tio in 1% steps.

To enter the ratio with the number keys
A Press [Mag. Ratio]. B Enter the desired ratio with the
number keys. C Press [#]. D Press [OK]. C Place your originals, and then
press the {Start} key.
the desired ratio, then adjust the ratio with [n] or [o]. A Press [Reduce/Enlarge].

Copier Functions


The machine can choose an appropri- ate reproduction ratio based on the paper and original sizes you select.
with this function.
This function calculates an enlarge- ment or reduction ratio based on the lengths of the original and copy.
❒When using Auto Reduce/Enlarge,
see the following table for original sizes and orientations you can use:


Exposure glass A3L, B4 JISL, A4KL, B5 JISKL
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, B6 JISKL, 11”× 17”L, 81/2" × 11"KL
the original and copy by compar- ing "A" with "a". A Press [Reduce/Enlarge] .

Exposure glass 11" × 17"L, 81/2" × 14"L, 81/2" × 11KL
A4LK, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2"KL
Copying · ❖Metric version · ❖Inch version

B Press [Specifd. Ratio]. C Make sure that [Specifd. Ratio] is
Copies can be reduced or enlarged at different reproduction ratios, hori- zontally and vertically.
with the number keys, and then press the [#] key.

following ranges:
1–999 mm (in increments of 1 mm)
0.1"–99.9" (in increments of 0.1")
E Enter the length of the copy with
the number keys, and then press [#].
close to the desired ratio using [Re- duce] or [Enlarge], then adjust with [n] or [o]. A Press [Reduce/Enlarge].
pressing [#], select [Original] or [Copy] and enter the desired length. F Press [OK]. G Press [OK]. H Place your original, and then

B Press [Specifd. Ratio]. C Press [Direct. Mag.%].
To enter the ratio with the number keys
A Press [Horizontal]. B Enter the desired ratio with the
number keys, followed by [#]. C Press [Vertical].
Copier Functions · Metric version · Inch version

D Enter the desired ratio with the
number keys, followed by [#]. E Press [OK].
The suitable reproduction ratios will be automatically selected when you enter the horizontal and vertical lengths of the original and copy im- age you require.
To specify a ratio with [n] and [o]
A Press [With no]. B Press [Horizontal]. C Adjust the ratio using [n] or

[o].
the ratio in increments of 1%. Pressing and holding down [n] or [o] changes it in in- crements of 10%. ❒If you have incorrectly en-
tered the ratio, readjust the ratio with [n] or [o]. D Press [Vertical]. E Adjust the ratio with [n] or
[o]. F Press [OK]. D Press [OK]. E Place your originals, and then
sizes of the original and those of the copy, as shown. ❒You can enter sizes within the fol-
press the {Start} key.
lowing ranges:
0.1"–99.9" (in increments of 0.1")
Copying · Metric version · Inch version


The machine can scan originals into memory and automatically sort cop- ies.
Reference Related initial settings p.102 “Select Stack Function” p.102 “Memory Full Auto Scan Re- start” p.101 “Rotate Sort: Auto Paper Continue” p.90 “Auto Tray Switching”
B Press [Specifd. Ratio]. C Press [Dir. Size Mag mm]. D Enter the horizontal size of the
original with the number keys, and then press [#]. E Enter the horizontal size of the
Copies are assembled as sets in se- quential order.
copy with the number keys, and then press [#]. F Enter the vertical size of the origi-
nal with the number keys, and then press [#]. G Enter the vertical size of the copy
2 1 3 2 1 3 2 1 3 2 1 3
with the number keys, and then press [#].
Every other copy set is rotated by 90°KL and delivered to the copy tray.
key you want to change and en- ter the new value. H Press [OK]. I Press [OK]. J Place the originals, and then press

2 1 3 2 1 3 2 1 3
the {Start} key.
two paper trays with paper identical in size and different in orientation (KL) are required.
Copier Functions · ❖Sort · ❖Rotate Sort

A Press [Sort] or [Rotate Sort].
❖When a finisher is not installed

❖When the 1000-Sheet finisher is

3 2 1 3 2 1 3 2 1
❖When the 2 Tray finisher is

❖When the booklet finisher is

Copying · ❖Shift Sort


with the number keys.
press the {Sample Copy} key. See p.33 “Sample copy”. C Place your originals.
exposure glass, start with the first page to be copied. When placing an original in the ADF, set so the first page is on the top. ❒When placing an original on the
One copy set is delivered as a sam- ple. C If the sample is acceptable, press
[Print]. The number of copies made is the number specified, minus one for the proof copy.
exposure glass or in the ADF us- ing Batch mode, press the {#} key after all the originals have been scanned. D Press the {Start} key.

checking the results, return to step A to adjust the copy set- tings as necessary. You can change the settings for Staple, Duplex (one-sided → one-sid- ed, one-sided → two-sided), Copy Orientation, Margin Ad- just., and Cover/Slip Sheet. However, depending on the combination of functions, you may not be able to change some settings.
Use this function to check the copy settings before making a long copy run.
when the Sort function is turned on. A Select Sort and any other neces-
sary functions, and then place the originals.
Copier Functions

Stack
You can change the number of copy sets during copying.
press the {Clear/Stop} key. B Press [Change Quantity].

3 3 3 2 2 2 1 1 1
with the number keys, and then press the {#} key.
ter differs depending on when the {Clear/Stop} key is pressed. D Press [Continue].
Copying starts again.
Copying


press the {Start} key.
exposure glass, start with the first page to be copied. When placing an original in the ADF, set so the last page is on the bot- tom. ❒When placing an original on the
exposure glass or in the ADF us- ing Batch mode, press the {#} key after all the originals have been scanned.
the number keys.
An optional finisher and the bridge unit are required to use this function.
Each copy set can be stapled together.

Reference Related initial settings p.102 “Select Stapling Position”
Copier Functions

Place all the originals in the ADF in the orientation in which they can be read nor- mally. When placing the original on the exposure glass, keep the same orientation, but set the original facing downwards. When there is copy paper that is identical in size and orientation to your original, the staple positions are as follows:

Copying · ❖1000-Sheet finisher

❖2 Tray finisher

Copier Functions



Copying · ❖Booklet finisher


*1 This table shows the stapling positions, not the orientation of delivery. *2 Not available for A3 and B4 JIS size paper. A Select one of the stapling positions.

Copier Functions · ❖1000-Sheet finisher

❖2 Tray finisher


Reference p.36 “Stapling position and original setting” B Enter the number of copy sets with the number keys. C Place your originals, and then press the {Start} key.
be copied. When placing an original in the ADF, set so the last page is on the bottom. ❒When placing an original on the exposure glass or in the ADF using Batch
mode, press the {#} key after all the originals have been scanned.
Copying · ❖Booklet finisher

The optional 2 Tray finisher and the bridge unit are required to use this function.
You can make punch holes in copies.




❒The relationship between the orientation in which you place the original and
the punch hole positions is as follows:
❖Punch hole positions

*1 This table shows the punch hole positions, not the orientation of delivery.
Copying


B Enter the number of copy sets with the number keys. C Place your originals, and then press the {Start} key.

Copies each side of a two-sided original onto two separate pages.
❖2 Sided → 2 Sided
Copies 1 two-sided page on one two-sided page.

Copier Functions


The resulting copy image will differ according to the orientation in which you place your originals (vertical K or horizontal L ).
Sided” or ”2 Sided to 2 Sid- ed”directly by pressing the Copy Function Key. In that case, proceed to D. B Select [1 Sided] or [2 Sided] for
Original, and then select [1 Sided] or [2 Sided] for Copy.
*1 The table shows the orientation of im- ages on the front and back of copies, not the orientation of delivery.
press [Orientation]. See p.45 “Originals and copy orienta- tion”. C Press [OK]. D Place your originals, and then
with this function. ❒The maximum paper weight that
can be used with duplex copying is 64–105 g/m2, 17–28 lb. (55–90 kg, 121.3–198.4 lb.).
press the {Start} key.
Reference p.58 “Margin Adjustment” Related initial settings p.95 “Front Margin: Left/Right” p.95 “Back Margin: Left/Right” p.95 “Front Margin: Top/Bottom” p.95 “Back Margin: Top/Bottom”
exposure glass, start with the first page to be copied. When placing an original in the ADF, set so the last page is on the bot- tom.
Copying

❒When placing an original on the
exposure glass or in the ADF us- ing Batch mode, press the {#} key after all the originals have been scanned.
Combine several pages onto one side of a sheet.
❖1 Sided 2 Pages → Combine 1 Side
Copies two one-sided originals to one side of a sheet.
You can select the orientation. • Top to Top

❖1 Sided 4 Pages → Combine 1 Side
Copies 4 one-sided originals to one side of a sheet.
❖1 Sided 8 Pages → Combine 1 Side
Copies 8 one-sided originals to one side of a sheet.
tation with User Tools. See p.92 “Copy Orientation in Duplex Mode” and p.92 “Original Orienta- tion in Duplex Mode” . A Press [Dup./Combine/Series]. B Press [Orientation], select the orien-
❖2 Sided 1 Page → Combine 1 Side
Copies 1 two-sided original to one side of a sheet.
❖2 Sided 2 Pages → Combine 1 Side
Copies 2 two-sided originals to one side of a sheet.
tation (Original/Copy), and then press [OK].
❖2 Sided 4 Pages → Combine 1 Side

Copies 4 two-sided originals to one side of a sheet.
Copier Functions · Duplex1 · Duplex2

❖Orientation of the original and image
Reference Related initial settings p.96 “Erase Original Shadow in Combine” p.98 “Copy Order in Combine” p.97 “Separation Line in Combine” A Press [Dup./Combine/Series].
position of combine Open to left R originals

B Press [1 Sided] or [2 Sided] for Orig-
inal, and then press [Combine 1 Side] for Copy.

Reference p.45 “Originals and copy orien- tation” C Select the number of originals to
combine, and then press [OK]. D Select the paper size. E Press [OK]. F Place your originals, and then
with this function.
press the {Start} key.
Copying

❖1 Sided 16 Pages → Combine 2 Side
Copies 16 one-sided originals to one sheet with eight pages per side.
Combines various pages of originals into one sheet with two sides.

❖1 Sided 4 Pages → Combine 2 Side
Copies 4 one-sided originals to one sheet with two pages per side.

❖2 Sided 4 Pages → Combine 2 Side
Copies 2 two-sided originals to one sheet with two pages per side.
❖1 Sided 8 Pages → Combine 2 Side
Copies 8 one-sided originals to one sheet with four pages per side.


❖2 Sided 8 Pages → Combine 2 Side
Copies 4 two-sided originals to one sheet with four pages per side.

Copier Functions

❖2 Sided 16 Pages → Combine 2 Side
B Press [1 Sided] or [2 Sided] for Orig-
Copies 8 two-sided originals to one sheet with eight pages per side.
inal, and then press [Combine 2 Side] for Copy.

Reference p.45 “Originals and copy orien- tation” C Select the number of originals to
Reference Related initial settings p.46 “Orientation of the original and image position of combine” p.96 “Erase Original Shadow in Combine” p.98 “Copy Order in Combine” p.97 “Separation Line in Com- bine” A Press [Dup./Combine/Series].
combine, and then press [OK]. D Select the paper size. E Press [OK]. F Place your originals, and then
press the {Start} key.

Copying

❖Front&Back→2 Sided
Copies each two-page spread orig- inal as it is onto both sides of a sheet.
Separately copies the front and back of a two-sided original or the two fac- ing pages of a bound original onto two sheets.

Limitation ❒You cannot use the Series Copies
function from the ADF.
❖Book→1 Sided
You can make one-sided copies from two facing pages of a bound original (book).

inal and copy paper sizes when using a 100% ratio.

❖Book→2 Sided
Copies a two-page spread original onto one sheet with one page per side.
B4 JISL B5 JISK × 2 sheets


11" × 17"L 81/2" × 11"K × 2 sheets
81/2" × 11"K × 1 sheet (two-sided)
81/2" × 11"L 51/2" × 81/2"K × 2 sheets
51/2" × 11"K × 1 sheet (two-sided)
Copier Functions · ❖Metric version · ❖Inch version


Make copies in page order for a folded booklet as shown.
B Press [Series/Book]. C Press [Series]. D Select [Book→1 Sided], [Book→2
Sided], or [Front&Back→2 Sided], and then press [OK]. E Press [OK]. F Make sure that [Auto Paper Select]
sure glass, and then press the {Start} key.
❖2 Sided→Booklet
Make two–sided originals to cop- ies in page order for a folded book- let as shown.
Copying

❖Open to left
❖Open to right


❖Open to right
❖2 Sided→Magazine

Copies two or more originals of two-sided to make copies in page order when they are folded and stacked.
❖Open to left

❖1 Sided→Magazine
Copies two or more originals to make copies in page order when they are folded and stacked.
❖Open to left
❖Open to right


Copier Functions


with this function. ❒The machine sets the reproduction
Reference Related initial settings p.96 “Erase Original Shadow in Combine” A Select “Open to left”or “Open to
right” with the User Tools.

Reference p.98 “Orientation: Booklet, Magazine” B Press [Dup./Combine/Series]. C Press [Series/Book]. D Press [Book]. E Select [1 Sided→Booklet], [2 Sided→-
Booklet], [1 Sided→Magazine] or [2 Sided→Magazine], and then press [OK]. F Press [OK]. G Select the paper. H Place your original, and then
exposure glass or in the ADF us- ing Batch mode, press the {#} key after all the originals have been scanned.
Copying

Reference Related initial settings p.96 “Image Repeat Separation Line” A Select the size of the copy paper
The original image is copied repeat- edly.

and the reproduction ratio. B Press [Edit/Stamp].
depends on the original size, copy paper size, and reproduction ratio. For example, see the following ta- ble:
C Press [Edit Image]. D Press [Image Repeat]. E Press [OK]. F Press [OK]. G Place your original, and then

Copier Functions

❒The originals of size A5L, B6
JISKL, 51/2" × 81/2"L cannot be detected properly on the exposure glass. Be sure to select the copy pa- per manually or place the originals in the ADF.
One original image is copied twice on one copy as shown.

Reference Related initial settings p.97 “Double Copies Separation Line” A Press [Edit/Stamp].
with this function. ❒See the following table for original
and copy paper sizes when using a 100% ratio:
B Press [Edit Image]. C Press [Double Copies]. D Press [OK]. E Press [OK]. F Select the paper. G Place your originals, and then
Original size and orientation
Copy paper size and orientation
51/2" × 81/2"L 81/2" × 11"K
51/2" × 81/2"K 81/2" × 11"L
81/2" × 11"K 11" × 17"L
Copying · ❖Inch version


You can make copies with the image moved to the centre.
C Press [Edit Image]. D Press [Centring]. E Press [OK]. F Press [OK]. G Place your originals, and then
with this function. ❒The original sizes and orientations
press the {Start} key.
for centring are listed below.

If your original is black and white, copy images are inverted.
A3L, B4 JISL, A4KL, B5 JISKL
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, B6 JISKL, 11" × 17"L
11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL
A3L, A4KL, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"K, 51/2" × 81/2"KL
Copier Functions · ❖Metric version

B Press [Edit Image]. C Press [Positive/Negative]. D Press [OK]. E Press [OK]. F Select the paper. G Place your originals, and then

This mode erases both the centre and edge margins of the original image.
This function erases the centre and/or all four sides of the original image. This function has the following three types:
Reference The erase width is set to 10 mm (0.4”) as a default. You can change this setting with User Tools. p.96 “Erase Centre Width” p.96 “Erase Border Width”
This mode erases the edge margin of the original image.

inal orientation and the erased part is as follows:

This mode erases the centre mar- gin of the original image.

Copying · ❖Border · ❖Centre


B Press [Erase]. C Set the erase border width.
you want to change and set an erase border width with [n] and [o]. C Press [OK]. D Press [OK]. E Place your originals, and then

press [n] and [o] to set the new value. C Press [OK].
B Press [Erase]. C Press [Centre]. D Set the erase centre width with
[n] and [o], and then press [OK]. E Press [OK]. F Place your originals, and then
press the {Start} key.
Copier Functions


B Press [Erase]. C Press [Centre/Border]. D Set the border to be erased.
want to change, and then set an erase margin width with [n] and [o]. C Press [OK]. E Press [OK]. F Place your originals, and then
You can shift the image to the left, right, top, or bottom to make a bind- ing margin.
B Press [Centre], and then set the
erase centre width with [n] and [o]. C Press [Border], and then set the
erase border width with [n] and [o]. D Press [OK].
Reference Related initial settings p.95 “Front Margin: Left/Right” p.95 “Back Margin: Left/Right” p.95 “Front Margin: Top/Bottom” p.95 “Back Margin: Top/Bottom” p.95 “1 Sided→2 Sided Auto Mar- gin: TtoT”
Copying

E Press [OK]. F Press [OK]. G Place your originals, and then
binding margin as follows:

Use this function to have numbers printed on the background of copies. It can help you to keep track of confi- dential documents.
B Press [Margin Adjustment]. C Set a binding margin for a front
page. Press [←] and [→] when set- ting the left and right margins, and [↓] and [↑] when setting the top and bottom margins.
press [←], [→], [↓], [↑] to set the new value. ❒If you do not need to specify the
Reference Related initial settings p.98 “Size” p.98 “Density” A Press [Edit/Stamp].
margins for the back side pages, press [OK] and proceed to step E. D Set a binding margin for the back

side pages. Press [←] and [→] when setting the left and right margins, and [↓] and [↑] when set- ting the top and bottom margins, and then press [OK].
page is valid only when [2 Sided] or [Combine 2 Side] is selected.
B Press [Stamp].
Copier Functions

C Press [Background Numbering]. D Enter the number to start count-
ing from with the number keys, and then press [OK]. E Press [OK]. F Press [OK]. G Place your originals, and then

Messages used frequently can be stored in memory and stamped on copies.
with this function. ❒Only one message can be stamped
Reference p.98 “Stamp Language” p.98 “Stamp Position” p.99 “Stamp Format” A Press [Edit/Stamp].
One of the following eight messages can be stamped on copies with a frame around it: "COPY", "URGENT", "PRIORITY", "For Your Info.", "PRE- LIMINARY", "For Internal Use Only", "CONFIDENTIAL", "DRAFT".

B Press [Stamp].
Copying

C Press [Preset Stamp]. D Select the desired message. E Press [All Pages] or [1st Page only] to
Copies with the registered stamp.

select the print page.
size, and density of the stamp. See p.61 “Changing the stamp position, size and density”. F After you specify all desired set-
tings, press [OK]. G Press [OK]. H Place your originals, and then
Preparation You have to register a user stamp before using this function. See p.62 “To program the user stamp”
press the {Start} key.

A Press [Change]. B Select the position for print, size,
and density, and then press [OK].
with this function. ❒Only one message can be stamped
at a time.
Copier Functions

Reference Related initial settings p.99 “Stamp Position 1 - 4” p.99 “Stamp Format 1 - 4” A Press [Edit/Stamp].
A Press [ Change ] . B Select the desired position, and
then press [OK].

readability is 10–297 mm high (0.4"–11.7") and 10–432 mm (0.4"– 17") wide. However, if the value exceeds the maximum value of the area (5,000 mm2, 7.75 inch2), it is corrected within the range of the area automatically. ❒Up to four images that you use fre-
B Press [Stamp]. C Press [User Stamp]. D Select the stamp you require. E Press [All Pages] or [1st Page only] to
quently can be stored in the ma- chine's memory. A Make sure that the machine is in
select the print page.

copier mode. B Press the {User Tools/Counter} key.
tures].

tion. See p.62 “To change the stamp position”. F After making all settings, press
[OK]. G Press [OK]. H Place the original, and then press
the {Start} key.
D Press [Stamp]. E Press [User Stamp].
Copying

F Press [Program/Delete Stamp]. G Press [Program], and then press the
N Press [Exit].
The display returns to the Copi- er/Document Server Features main menu. O Press [Exit].
stamp number (1–4) you want to program.
Exits settings and gets ready to copy.
have settings in them. ❒If the stamp number is already
being used, the machine will ask you if you want to over- write it . Press [Yes] or [No]. H Enter the user stamp name with
the letter keys on the display pan- el. You can register up to 10 char- acters. I Press [OK].
copier mode. B Press the {User Tools/Counter} key.
Reference “Entering Text”, General Set- tings Guide J Enter the horizontal size of the
tures].
stamp with the number keys, and then press [#]. K Press [Vertical], and then enter the
vertical size in the same way as step J. L Place the original for user stamp
on the exposure glass, and then press [Start Scanning]. The original will be scanned, and the stamp will be registered.
D Press [Stamp]. E Press [User Stamp]. F Press [Program/Delete Stamp]. G Press [Delete], and then press the
from the ADF when program- ming the user stamp. M Press [Exit].
stamp number you want to delete. H Select [Delete], and then press [Ex-
it].
Copier Functions

I Press [Exit].
The display returns to the Copi- er/Document Server Features main menu. J Press [Exit].

Use this function to print dates on your copies.
Reference Related initial settings p.100 “Font” p.100 “Size” p.100 “Superimpose” p.100 “Stamp Position” “Timer Settings”, General Settings Guide A Press [Edit/Stamp].

Copying


B Press [Stamp]. C Press [Date Stamp]. D Press [All Pages] or [1st Page only] to
sition of the date to be stamped. See p.65 “To change the style of date”. E After all settings are complete,
Use this function to print page num- bers on your copies.

press [OK]. F Press [OK]. G Place the original, and then press
press [OK].
Copier Functions


B Press [Stamp]. C Press [Page Numbering]. D Select the format.
Reference Related initial settings p.100 “Font” p.100 “Size” p.101 “Superimpose” p.100 “Stamp Format” p.100 “Duplex Back Page Stamp- ing Position” p.101 “Stamp Position” p.101 “Stamp on Designated Slip Sheet”
tion, pages to be stamped, and numbering. See p.66 “Changing the stamp position” and p.67 “Specify the first printing page and what page to number”. E After you specify all desired set-
tings, press [OK]. F Press [OK]. G Place the originals, and then press
the {Start} key.
A Press [ Change ] . B Select the desired position, and
then press [OK].
Copying
![Page 82 of the Lanier LD045 user manual — A Press [ Change ] on the right hand](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/page-82.webp?w=400)
number of the page at which to stop numbering with the number keys, and then press the {#} key.

If you selected (P1, P2…, -1-,-2-…, P.1, P.2…, 1, 2…, )
(P1, P2...) is selected. The steps are the same for other cases. A Press [Change] on the right side. B Press [First Printing Page], and then
enter the original sheet number from which to start printing, and then press the {#} key.
to the end, press [to the end]. E When page designation is com-

plete, press [OK]. F Press [OK].
side. B Press [ First Printing Page ] , and then
enter the original sheet number from which to start printing, and then press the {#} key.
press [Clear] or the {Clear/Stop} key, and then enter a new number. C Press [Numbering from/to], enter the
![Lanier LD045 — A Press [ Change ] on the right hand diagram (page 82)](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/fig-82-3.webp)
number of the page from which to start numbering with the number keys, and then press the {#} key.
the first printing page is “2”and the start number is “3”.
999 for the original sheet number from which to start printing.
Copier Functions
![Page 83 of the Lanier LD045 user manual — A Press [ Change ] on the right hand](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/page-83.webp?w=400)
❒To change the number entered,
If you selected (1-1, 1-2,…)
press [Clear] or the {Clear/Stop} key, and then enter a new number. C Press [Numbering from/to], and then
side. B Press [ First Printing Page ] , and then
enter the number of page from which to start numbering with the number keys, and then press the {#} key. D Press [Last Number], and then enter
enter the original sheet number from which to start printing, and then press the {#} key.
![Lanier LD045 — A Press [ Change ] on the right hand diagram (page 83)](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/fig-83-1.webp)
the number of page at which to stop numbering with the number keys, and then press the {#} key. Proceed to step E when not chang- ing .
page, press [to the end]. ❒The last number is the last page
press [Clear] or the {Clear/Stop} key, and then enter a new number. C Press [First Chapter No.], enter the
number to print. For example, if [Total Pages] is ten, if you want to print up to seven pages and do not want to print from page 8 on, enter [7] for [Last Number]. Normally, you do not need to enter the number. E Press [Total Pages], enter the total
chapter number from which to start numbering with the number keys, and then press the {#} key.
number of original pages with the number keys, and then press the {#} key. F When page designation is com-
999 for the chapter number from which to start numbering. D Press [Numbering from/to], and then
plete, press [OK].
enter the page number from which to start printing with the number keys, and then press the {#} key. E Press [OK]. F When page designation is com-
pressing [OK], press [Change], and then enter the numbers again.
plete, press [OK].
Copying
![Page 84 of the Lanier LD045 user manual — B Press [ Front Cover ] or [ Front/Back](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/page-84.webp?w=400)

Using this function, you can create cover sheets by adding additional pages of different paper or copying existing pages on different paper.
Preparation Before selecting this function, set the tray for the front cover paper. See “Cover Sheet Tray”in “Tray Paper Settings”, General Settings Guide.
The first and last pages of your original are copied on specific pa- per for use as covers. • Copy
size and orientation as the copy pa- per. ❒You cannot set the copy paper in
4 3 2 1
the bypass tray. ❒When selecting [Copy], select whether the front and back covers are copied one-sided or two-sided. See “Cover Sheet Tray”in “Tray Paper Settings”, General Settings Guide.

The first page of your originals is copied on specific paper sheet for covers, or a cover sheet is inserted before the first copy. • Copy
Reference p.97 “Front Cover Copy in Combine” A Press [Cover/Slip Sheet].

Cover].
Copier Functions · ❖Front/Back covers · ❖Front cover

![Lanier LD045 — C Select [ Copy ] or [ Blank ] for the cov- diagram (page 85)](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/fig-85-1.webp)
the sheet paper to copy the origi- nals, and then press [OK]. E Place your originals in the ADF,
B Press [Desig./Chapter]. C Press the key to select the chapter
Use this function to have certain pag- es of your original copied onto slip sheets.

original's location you want to copy onto a slip sheet with the number keys, and then press the {#} key. E Select the paper tray for slip
repeat steps C to E.
Preparation Before using this function, set the special paper tray for slip sheets. See “Cover Sheet Tray”and “Slip Sheet Tray”in “ Tray Paper Set- tings”, General Settings Guide.
the [T11∼20] key. G When page designation is com-
plete, press [OK]. H Press [OK]. I Select the paper tray that contains
size and orientation as the copy pa- per. ❒You cannot set the copy paper in
the sheet paper to copy the origi- nals. J Place your originals in the ADF,
the bypass tray. ❒You can specify the pages up to 20.
and then press the {START} key.
Copying

plete, press [ OK ] . H Place your originals, and then
The page locations you specify with this function will appear on the front of copy sheets.
press the {Start} key.
Preparation Before selecting this function, press [Dup./Combine/Series] and se- lect Duplex (1 Sided → 2 Sided) mode or Combine mode.
Using this function, you can insert a slip sheet between OHP transparen- cies or stacks. You can also print on the inserted slip sheet.

when you use the Duplex (1 Sided→2 Sided) or Combine func- tion. ❒You can specify the pages up to 20. A Press [Cover/Slip Sheet].
Preparation Before selecting this function, specify the paper tray for slip sheets. See "Slip Sheet Tray" in “Tray Paper Settings”, General Set- tings Guide.
B Press [Desig./Chapter]. C Press [Chapter]. D Press the key to select the chapter
size and orientation as the copy pa- per or the OHP transparency.
❖When using OHP transparencies
page of the first chapter with the number keys, and then press the {#} key. F To specify another page location,
repeat steps D to E.
the [T11-20] key.
Copier Functions
![Page 87 of the Lanier LD045 user manual — press [ OK ] . D Select the paper tray containing](/cdn/reader/4c/4c62cdb462b873ee915e54b7552e53b1a324b4ecdbd5c9d3904f1b39e9aeaddc/images/page-87.webp?w=400)

Sheet] in Special paper. See p.19 “When copying onto special pa- per”. A Press [Cover/Slip Sheet].

B Press [Slip Sheet]. C Select [Copy] or [Blank], and then
the sheet paper to copy the origi- nals. E Place the originals, and then press
the {Start} key.
Copying

Storing Data in the Document Server
The Document Server enables you to store documents in the memory and print them as you want.
Reference For details about how to regis- ter the file name, user name or password, see General Settings Guide. C Press [OK]. D Place the originals.
be lost if some kind of failure oc- curs. The supplier shall not be re- sponsible for any damage that might result from the loss of data.
Reference For more information about the types of originals that can be placed and how to place them, see p.10 “Placing Originals”. E Make the scanning settings for
er is set to be deleted after three days by the factory default. You can specify the period after which the stored data is deleted automat- ically. For more information about settings, see “Auto Delete File “ in “Key Operator Tools”, General Set- tings Guide. A Press [Store File].
the original.


F Press the {Start} key.
Originals are scanned and stored in memory.
password if necessary.
{Clear/Stop} key. To resume a paused scanning job, press [Resume] in the confirmation di- alog box. To delete scanned im- ages and cancel the job, press [Cancel]. The originals placed in the ADF are delivered. ❒To check if the document has

been stored, press the {Docu- ment Server} key.

You can store frequently used copy job settings in the machine memory and recall them for future use.

or program No. 10 as the mode to be set when modes are cleared or reset, or immediately after the op- eration switch is turned on. See p.92 “Change Initial Mode” . ❒Paper settings are stored based on
want to store.
against them already have set- tings in them.
paper size. So if you place more than one paper tray of the same size, the paper tray prioritized with User Tools (System Settings) will be selected first. See “Paper Tray Priority”in “Tray Paper Set- tings”, General Settings Guide. ❒Programs are not deleted by turn-
Reference p.75 “Changing a stored pro- gram” E Enter the program name with the
letter keys on the display panel. You can enter up to 40 characters.
ing the power off or by pressing the {Clear Modes} key. They are canceled only when you delete or overwrite them with another pro- gram. A Edit the copy settings so all func-

tions you want to store in this pro- gram are selected. B Press the {Program} key.
Reference For details about entering char- acters, see “Entering Text”, Gen- eral Settings Guide.
program name, proceed to step F.
Copying

F Press [OK].
want to delete. D Press [Yes].
When the settings are successfully stored, m appears on the left side and the program name appears on the right side of the registered pro- gram number. The display returns to the initial copy display for a while.
The program is deleted, and the display returns to the initial copy display.

A Press the {Program} key. B Press [Recall].
contents of a program, recall the program. See p.75 “Recalling a Program”. B Repeat steps A to D of “Storing a
Repeat steps E, F of ”Storing a Pro- gram”.
want to recall. The stored settings are displayed.
vious program is deleted.
against them already have set- tings in them. D Place the originals, and then press

A Press the {Program} key. B Press [Delete].
Programs

Copying

If Your Machine Does Not Operate As You Want
The following chart contains explanations for the common messages. If other messages appear, follow the instructions as they are displayed.
Cannot detect original size. Improper original is
Select paper manually, not in Auto Paper Select mode, and do not use Auto Reduce/Enlarge function.
placed. See p.9 “Sizes diffi- cult to detect”.
Place the original on the exposure glass. See p.11 “Placing Originals on the Exposure Glass” .
Original is not placed. Place your originals.
Check original orientation. Original is not placed in a proper orientation.
Change the orientation of the origi- nal.
Check paper size. Improper paper size is set. If you press the {Start} key, copy will start onto the selected paper.
Rotate Sort is not available with this image size.
A size of paper for which Rotate Sort is not available is selected.
Select the proper paper size. See p.31 “Sort”.
Cannot punch paper of this size.
The Punch function cannot be used with paper size se- lected.
The following paper sizes are avail- able for Punch mode: A3L, B4 JISL, A4KL, B5 JISKL, A5KL, 11" × 17"L, 81/2" × 14"L and 51/2" × 81/2"KL. Select one of these sizes.
It is over stapling capacity. The number of sheets per set is over the staple capac- ity.
Check the stapler capacity. See p.108 “Staple”.
Cannot staple paper of this size.
The Staple function cannot be used with paper size se- lected.
Select a paper size that can be used in Staple mode. See p.108 “Staple”.
Duplex is not avilable with this paper size.
A paper size not available in Duplex mode has been selected.
The following paper sizes are avail- able for Duplex mode: A3L, B4 JISL, A4KL, B5 JISKL, A5L. Select one of these sizes.
Message Causes Solutions


The number of copies ex- ceeds the maximum copy quantity.
You can change the maximum copy quantity. See p.92 “Max. Copy Quantity”.
Cannot copy. Original is being scanned by other functions.
To cancel the job in process, press [Exit], and then press the {Document Server} key. Next, press the {Clear/Stop} key. When the message ” [Stop] key was pressed. Stop stor- ing?” appears, press [Stop].
Troubleshooting

If You Cannot Make Clear Copies

Copies appear dirty. The image density is too dark.
Adjust the image density. See p.21 “Adjusting Image Density”.
Adjust the auto density. See p.21 “Adjusting Image Density”.
The reverse side of an orig- inal image is copied.
Adjust the image density. See p.21 “Adjusting Image Density”.
Adjust the auto density. See p.21 “Adjusting Image Density”.
A shadow appears on cop- ies if you use pasted origi- nals.
Adjust the image density. See p.21 “Adjusting Image Density”.
The same copy area is dirty whenever making copies.
Copies are too light. The image density is too light.
Adjust the image density. See p.21 “Adjusting Image Density”.
Copies are blank. The original is not set cor- rectly.
When using the exposure glass, face the originals down. When using the ADF, face them up. See p.10 “Plac- ing Originals”.
Your original has a dot pat- tern image or many lines.
Place the original on the exposure glass at a slight angle.

This section explains causes and remedies when copy results are not as expect- ed.
Copies are not stapled. There are jammed staples in the stapler.
Remove jammed staples. See Gener- al Settings Guide.
staples might not be ejected the first few times you try to use the stapler.
The number of copies ex- ceeds the capacity of the stapler.
Check the stapler capacity. See p.108 “Staple”.
Copy paper is curled. Turn the copy paper over in the tray.
Staples are wrongly posi- tioned.
Originals are not set cor- rectly.
Check the correct position to place the originals. See p.35 “Staple”.
You cannot combine sever- al functions.
Selected functions cannot be used together.
Check the combination of functions and make the settings again.
Reference p.103 “Combination Chart”
When sorting, the pages are divided into two blocks.
The memory became full in the middle of sorting and the pages were delivered in two blocks.
You can interrupt copying when the memory becomes full. See p.102 “Memory Full Auto Scan Restart”.
Paper does not output dur- ing printing with stapling.
When you stop printing while using the staple func- tion, papers not stapled during printing may be left in the staple unit.
Press the {Reset} key and cancel copy settings, including stapling.
Troubleshooting · ❖Basic · Problem Causes Solutions

If You Cannot Make Copies As You Want
In Double Copies mode, parts of the original image are not copied.
Combination of original and copy paper is not cor- rect.
Select A3L for A4 K originals and A4 for A5 originals.
In Border, Centre, or Cen- tre/Border mode, parts of the original image are not copied.
You set a wide erased mar- gin.
Make the margin width narrower. You can adjust it between 2–99 mm (0.1"–3.9"). See p.96 “Erase Border Width”and p.96 “Erase Centre Width”.
Originals are not scanned correctly.
Place the originals correctly.
In Margin Adjustment mode, parts of the original image are not copied.
You set a wide erased mar- gin.
Set a narrower margin with User Tools. You can set the width be- tween 0–30 mm (0"–1.2"). See p.95 “Front Margin: Left/Right”, p.95 “Front Margin: Top/Bottom”, p.95 “Back Margin: Left/Right”, and p.95 “Back Margin: Top/Bottom”.
There is a lack of margin space on the opposite side of the binding position.
In Image Repeat mode, the original image is not cop- ied repeatedly.
You selected copy paper the same size as the originals, or you did not select the proper reproduction ratio.
Select copy paper larger than the originals.
Select the proper reproduction ratio.
The stamp position is wrong.
The paper orientation is wrong.
Check the paper orientation and stamp position.

You cannot make a book from Booklet or Magazine mode by folding copies.
You selected a setting (“Open to left”or “Open to right”) that does not match the orientation of originals.
When using Combine, parts of the image are not copied.
You specified a reproduc- tion ratio that does not match the sizes of your originals and copy paper.
When you specify a reproduction ra- tio using Manual Paper Select mode, make sure that the ratio matches your originals and the copy paper.


When placing a stack of originals in the ADF, the last page should be on the bottom.
If you place an original on the expo- sure glass, start with the first page to be copied.

When using Duplex, copy is made Top/Bottom even though Left/Right is selected.
Place the originals in the correct ori- entation. See p.10 “Original Orienta- tion” .
When placing a stack of originals in the ADF, the last page should be on the bottom.
If you place an original on the expo- sure glass, start with the first page to be copied.
Full Auto Scan Restart” ) to [Yes], even if the memory becomes full, the mem- ory overflow message will not be displayed. The machine will make copies of the scanned originals first, then automatically proceed scanning and copying the remaining originals. In this case, the resulting sorted pages will not be se- quential.

The scanned original exceeds the number of pages that can be stored in memory.
Press [Output] to copy scanned originals and cancel the scan- ning data. Press [Clear] to can- cel the scanning data and not copy.
message will be displayed when the memory is full.
Press [Resume] to scan and copy remaining originals.
The machine checks if the re- maining originals should be copied, after the scanned orig- inal has been printed.
To continue copying, remove all copies, and then press [Resume]. To stop copying, press [Stop].
Troubleshooting · ❖Duplex


General Features 1/4 See p.90 “General Features 1/4”.
General Features 2/4 See p.92 “General Features 2/4”.
Duplex Mode Priority 1 Sided → 1 Sided (metric)

User Tools (Copier/Document Server Features)

General Features 3/4 See p.93 “General Features 3/4”.
General Features 4/4 See p.93 “General Features 4/4”
Reproduction Ratio 1/2 See p.94 “Reproduction Ratio 1/2”.

User Tools Menu (Copier/Document Server Features)

Reproduction Ratio 2/2 See p.94 “Reproduction Ratio 2/2”.
Edit 1/2 See p.95 “Edit 1/2”.
1 Sided→2 Sided Auto Margin: TtoT Metric version: Right 5 mm
1 Sided→2 Sided Auto Margin: TtoB Metric version: T/B 0 mm

User Tools (Copier/Document Server Features)

Edit 2/2 See p.96 “Edit 2/2”.

User Tools Menu (Copier/Document Server Features)


User Tools (Copier/Document Server Features)


Accessing User Tools (Copier/Document Server Features)
This section is for the key operators in charge of this machine. You can change or set the machine's default.
tures]. The Copier/Document Server Fea- tures menu appears. C Select the menu you want to set.
return to the initial copy display after all the settings are finished. This section describes system set- tings that you can set for the copi- er. ❒The selected key is highlighted. ❒Any changes you make with User
The setting display for each menu will be shown.
Reference p.83 “User Tools Menu (Copi- er/Document Server Features)” D Change settings by following the
Tools remain in effect even if the main power switch or operation switch is turned off, or the {Clear Modes} key is pressed.
instructions on the display panel, and then press [OK].
Reference For details, see "User Tools (Sys- tem Settings)", General Settings Guide. A Press the {User Tools/Counter} key.
A After changing User Tools set-
tings, press [Exit] on the User Tools main menu. Changes to User Tools are com- plete, and the machine is ready to copy.
The User Tools main menu ap- pears.

access code input display is shown when changing the ini- tial settings. Operate by enter- ing the registered access code beforehand. For access code, see “Key Operator Tools”, General Settings Guide.
Tools by pressing the {User Tools/Counter} key.

User Tools (Copier/Document Server Features)
❖Auto Paper Select Priority
is shown as below. When [Auto Paper Select] is pressed, paper sizes appear on the display.
As a default, Auto Paper Select is selected. You can cancel this set- ting. See p.23 “Selecting Copy Pa- per”.

If you load paper of the same size in two or more trays, the machine automatically shifts to the other tray when the first tray in use runs out of paper (when Auto Paper Se- lect is selected.) This function is called "Auto Tray Switching". This setting specifies whether to use Auto Tray Switching or not.
❖Original Type Priority
You can select the type of originals to be effective when the power is turned on, reset or modes are cleared. See p.22 “Selecting Origi- nal Type Setting”.
copy with Auto Tray Switching. ❒[Without image rotation] Only cop-
❖Original Type Display
You can choose to have the origi- nal types shown on the initial dis- play.
ies with Auto Tray Switching if you load paper of the same size and in the same direction in two or more trays. If the paper is not the same size or in the same ori- entation, copying is interrupted and the message "Load paper." is displayed. ❒[OFF] When a paper tray runs
is shown as below.

out of paper, copying is inter- rupted and the message "Load paper." is displayed.
You can choose to have the availa- ble paper trays and sizes shown on the initial display.
❖Paper Display

Accessing User Tools (Copier/Document Server Features)
❖Auto Image Density Priority
❒[Custom Setting] is the value
Set this function to use Auto Image Density when the power is turned on, reset or modes are cleared.
set during service setup. ❒Select [Print Photo] for printed
photo originals, and [Glossy Photo] for printed photo orig- inals with fine dots. ❒Select [Normal] for printed
photo and text originals. • Pale Adjust the quality level for the finish of a pale original with normal density.
You can adjust the quality level of copies for each of the original types (Text, Text/Photo, Photo, Pale, Generation Copy). • Text Adjust the sharpness of text.
set during service setup. • Generation Copy Adjust the quality level so as not to thicken the lines of the finish image.
set during service setup. ❒Choosing [Sharp] or [Sort] af-
fects the outline sharpness of text. • Text/Photo When there are photo(s) and text on the original, determine whether the photo or text takes priority.
set during service setup.
You can select one of seven origi- nal image density levels for each of the original types (Text, Text/Pho- to, Photo, Pale, Generation Copy).
set during service setup. ❒[Normal] achieves a good bal-
ance between text and pho- tos. • Photo For a photo original, adjust the finish quality level to match the type of photo original.
❖Copy Quality · ❖Image Density

User Tools (Copier/Document Server Features)
The beeper (key tone) sounds if you forget to remove originals af- ter copying.
❖Duplex Mode Priority
You can select the type of Duplex function effective when the ma- chine is turned on, reset, or modes are cleared.
tem Settings) is [Off], the beeper does not sound irrespective of the Tone: Original remains set- ting. See "Panel Tone" in “Gen- eral Features”, General Settings Guide.
❖Copy Orientation in Duplex Mode
You can set the copy orientation when making two-sided copies.
❖Job End Call
You can choose whether or not the beeper sounds when copying is complete.
❖Original Orientation in Duplex Mode
You can set the original orientation when making two-sided copies.
tem Settings) settings is [On], the machine beeps to notify you that it did not complete a job for reasons such as copying was in- terrupted, the paper tray ran out of paper, or a paper jam oc- curred.
❖Change Initial Mode
You can select initial mode or Pro- gram No. 10 as the mode effective when the machine is turned on, re- set, or modes are cleared.
❖Max. Copy Quantity
The maximum copy quantity can be set between 1 and 999.

Accessing User Tools (Copier/Document Server Features)
General Features 4 / 4
You can assign frequently used functions to function keys F1 to F5.
You can assign frequently used functions to function keys F1 to F5. You can also change the assigned functions.


User Tools (Copier/Document Server Features)
You can set the ratio with priority when [Reduce/Enlarge] is pressed, followed by [Enlarge].
You can register up to three fre- quently used Reduce/Enlarge ra- tios other than the fixed Reduce/Enlarge ratio and have them shown on the initial display. You can also change registered Re- duce/Enlarge ratios. If no Reduce/Enlarge ratio has been set when selecting [Shortcut R/E 1], [Shortcut R/E 2], or [Shortcut R/E 3], enter the desired Re- duce/Enlarge ratio using the number keys.
You can customize available re- duction ratios by pressing [Re- duce/Enlarge] followed by [Reduce].
You can customize available en- largement ratios by pressing [Re- duce/Enlarge] followed by [Enlarge].
Reduce1 Reduce2 Reduce3 Reduce4 Reduce5 Reduce6

Enlarge1 Enlarge2 Enlarge3 Enlarge4 Enlarge5
tio], enter a ratio using the number keys (in the range of 25 to 99%).
tio], enter a ratio using the number keys (in the range of 101 to 400%).
❖Shortcut R/E · ❖Reduce 1-6 · ❖Enlarge 1-5

Accessing User Tools (Copier/Document Server Features)
You can set the ratio with priority when [Reduce/Enlarge] is pressed, followed by [Reduce].
You can specify left and right mar- gins on the front side of copies in Margin Adjust mode.
❖Ratio for Create Margin
You can set a Reduce/Enlarge ra- tio when registering Create Mar- gin in a shortcut key.
You can specify left and right mar- gins on the back side of copies in Margin Adjust mode.
Specifies which tab is given priori- ty on the display panel when [Re- duce/Enlarge] is pressed.
You can specify top and bottom margins on the front side of copies in Margin Adjust mode.

You can specify top and bottom margins on the back side of copies in Margin Adjust mode.
❖1 Sided→2 Sided Auto Margin: TtoT
In 1 sided → 2 sided Duplex mode, you can specify the margins on the back side. The margin is set to the same value of “Back Margin: Left/Right”.
❖R/E Priority

User Tools (Copier/Document Server Features)
mm (0.06”) will not be displayed as the width of the separation line, when specifying solid or broken lines.
❖1 Sided→2 Sided Auto Margin: TtoB
In 1 sided → 2 sided Duplex mode, you can specify the margins on the back side. The value set for "Back Margin: Top/Bottom" is used.
❖Image Repeat Separation Line
You can select a separation line in Image Repeat mode from None, Solid, Broken A, Broken B, or Crop Marks. • None
❖Erase Border Width
You can specify the width of the erased border margins with this function.
❖Erase Original Shadow in Combine
In Combine mode, you can specify whether to erase a 3 mm, 0.1" boundary margin around all four edges of each original.
❖Erase Centre Width
You can specify the width of the erased centre margins with this function.

Accessing User Tools (Copier/Document Server Features)
❖Double Copies Separation Line
You can select a separation line in Double Copies mode from None, Solid, Broken A, Broken B, or Crop Marks. • None
❖Copy on Designating Paper
You can specify whether to copy on the designate.
❖Front Cover Copy in Combine
You can make a combined copy on the front cover sheet when you se- lect Front cover mode.
❖Separation Line in Combine
You can select a separation line in Combine mode from None, Solid, Broken A, Broken B, or Crop Marks. See p.45 “One-Sided Com- bine” and p.47 “Two-Sided Com- bine” • None
❖Copy on Designating Page in Com-
bine You can specify whether to make a combined copy on the inserted slip sheets in Desig./Chapter Copy mode.
Combine Not Combined

User Tools (Copier/Document Server Features)
You can select the type of originals for Booklet or Magazine mode.
Reference p.52 “How to fold and unfold copies to make a booklet” p.52 “How to fold and unfold copies to make a magazine”
You can set the size of the num- bers.
❖Copy Order in Combine
You can set the copy order in Com- bine mode to Left to Right or Top to Bottom.

You can set the density of the num- bers.
You can select the stamp type giv- en priority when [Preset Stamp] is pressed. See p.60 “Preset Stamp”.
You can select the language of the message printed in Stamp mode.
You can set the position at which the stamp is printed. Press the arrow keys to adjust the position.

Accessing User Tools (Copier/Document Server Features)
You can register, change, or delete these designs as user stamps.
tom stamps with your favorite designs. See p.62 “To program the user stamp”.
Reference For how to delete the user stamp, see p.63 “To delete the user stamp”.
You can adjust the size, density, and print page for the stamp. • Size You can set the size of the stamp.
❖Stamp Position 1 - 4
You can set the position at which the stamp is printed. Press the arrow keys to adjust the position.
ed on the image. You cannot check which parts will over- lap. ❒Lighter : The image can be
seen through the stamp. ❒Lightest : You can see the im-
❖Stamp Format 1 - 4
age even clearer than in the Lighter setting. • Page to Stamp You can have the stamp printed on the first page or all pages.
You can adjust the print page for User Stamps 1 to 4 already regis- tered. • Page to Stamp Sets whether to print the stamp on all pages or only on the first page.
❖Program/Delete Stamp · ❖Stamp Format

User Tools (Copier/Document Server Features)
You can set the Date Stamp size.
You can select the date format for Date Stamp mode.
You can have the Date Stamp printed in white when it overlaps black parts of the image.
You can select the Date Stamp font.
You can select the page number format given priority when [Page Numbering] is pressed.
Numbering.
You can set the position at which the stamp is printed. Press the arrow keys to adjust the position.
You can select the page number printed in Page Numbering mode.
You can set the size of the stamp printed in Page Numbering mode.
❖Duplex Back Page Stamping Position
You can set the position of the du- plex back page number printed in Duplex mode.
You can have the date printed on the first page or all pages.

Accessing User Tools (Copier/Document Server Features)
❖Page Numbering in Combine
You can set page numbering when using the Combine function and the Page Numbering function to- gether.
❖Switch to Batch (SADF)
You can select to have Batch mode or SADF mode displayed when you press the Special Original key. See p.12 “Batch mode”.
❖Stamp on Designated Slip Sheet
You can select to print the page number onto slip sheets when us- ing the Designate function set to [Copy] and the Page Numbering function together.
❖SADF Auto Reset
When you set one original at a time in the ADF, the Auto Feed indica- tor lights for a specified time after an original is fed to show that the ADF is ready for another original. You can adjust this time from 3 sec- onds to 99 in 1 second increments.
P1, P2... Stamp Position: 1/5, 2/5... Stamp Position: –1–, –2–... Stamp Position: P.1, Pie. Stamp Position: 1, 2... Stamp Position: 1–1, 1–2... You can set the position at which the stamp is printed. Press the arrow keys to adjust the position.
You can specify to continue copy- ing when paper of the required ori- entation has run out during rotate- sorting. See p.31 “Rotate Sort”.
You can have page numbers print- ed in white when they overlap black parts of the image.
❖Stamp Position · ❖Superimpose

User Tools (Copier/Document Server Features)
❖Select Stapling Position
You can specify whether Sort mode is selected when the ma- chine is turned on or the mode is cleared. Default: No
Specify which Top 2 staples or Bot- tom is shown on the initial display with priority.
❖Memory Full Auto Scan Restart
When memory becomes full while scanning originals, the machine can make copies of scanned origi- nals first, and then automatically proceed scanning remaining origi- nals. You can enable or disable this function.
booklet finisher is required to use this function.
❖Select Punch Type
Specify which punch type (2 holes or 3 holes) has priority to be shown on the initial display.
equipped with the punch func- tion is required.
If you select [Yes] in this function, the machine rotates the image cor- rectly.
tom) or two-sided paper might not be printed correctly de- pending on how the originals and paper are placed.
❖Select Stack Function
Specify whether Stack or Rotate Sort has priority to be shown on the initial display.
Reference When using letterhead paper, be careful of the paper orienta- tion. See “Orientation–Fixed Pa- per or Two-Sided Paper”in “Loading Paper”, General Set- tings Guide.
to use this function.
❖Auto Sort · ❖Letterhead Setting


The combination chart given below shows which modes can be used together. When you read the chart, see the following table:
❍ means that these modes can be used together.
$ means that these modes cannot be used together. The second mode selected will be the mode you're working in.
× means that these modes cannot be used together. The first mode selected will be the mode you're working in.

❖Mixed Size mode
❖Bypass Tray Copy

141 (enlarge area by 2) A4→A3, A5→A4
75 B4 JIS→F4, B4 JIS→F
71 (reduce area by 1/2) A3→A4, A4→A5
50 (reduce area by 1/4) A3→A5, F→A5
Specifications · ❖Preset Enlarge/Reduce · ❖Metric version


200 (enlarge area by 4) 51/2" × 81/2"→11" × 17"
155 (enlarge area by 2) 51/2" × 81/2"→81/2" × 14"
129 81/2" × 11"→11" × 17"
121 81/2" × 14"→11" × 17"
85 F→81/2" × 11"
78 81/2" × 14"→81/2" × 11"
73 11" × 15"→81/2" × 11"
65 11" × 17"→81/2" × 11"
50 (reduce area by 1/4) 11" × 17"→51/2" × 81/2"
❖Directional Size Magnification

❖Sort, Rotate Sort, Stack

A3L, B4 JISL, A4KL, B5 JISKL, A5KL, 51/2" × 81/2"KL, 11" × 17"L, 81/2" × 14"L, 81/4" × 13"L, 8" × 13"L, 81/2" × 11"KL, 71/4" × 101/2"KL, 12" × 18"L *1
A3L, B4 JISL, A4KL, B5 JISKL, A5KL
A3L, B4 JISL, A4KL, B5 JISK,
11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2"KL
11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL

500 sheets *1 (80 g/m2) (20 lb.)
250 sheets *2 (80 g/m2) (20 lb.)
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, B6 JISL, A6L, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 71/4" × 101/2"KL, 51/2" × 81/2"L, 8" × 13"L, 81/2" × 13"L, 81/4" × 13"L
A4KL, B5 JISKL *4 , A5KL, 71/4" × 101/2"L, 51/2" × 81/2"KL
A3L, B4 JISL, 12" × 18"KL, 11" × 17"L, 81/2" × 14"L, 8" × 13"L, 81/4" × 13"L 500 sheets (80 g/m2) (20 lb.)
Specifications

Paper size and orientation Paper capacity and weight
2 Tray finisher Finisher shift tray 1
A4KL, 81/2" × 11"KL, A5K, B5 JISKL 500 sheets (80 g/m2) (20 lb.)
A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L 250 sheets (80 g/m2) (20 lb.)
A5L, 51/2" × 81/2"KL 100 sheets (80 g/m2) (20lb.)
Finisher shift tray 2
A4K, 81/2" × 11"K 2,000 sheets *5 (80 g/m2) (20 lb.)
A3L, B4 JISL, A4L, B5 JISKL, A5K, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"L 750 sheets (80 g/m2) (20 lb.)
A5K 500 sheets (80 g/m2) (20lb.)
A5L, 51/2" × 81/2"KL 100 sheets (80 g/m2) (20lb.)
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, B6 JISL, A6L, 11" × 17"L, 11" × 15"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2"L
150 sheets (80 g/m2) (20 lb.)
A4K, B5 JISKL, A5K, 81/2" × 11"K 1000 sheets (80 g/m2) (20 lb.)
A3L, B4 JISL, A4L, 11" × 17"L, 81/2" × 11"L 500 sheets (80 g/m2) (20 lb.)
A3L, B4 JISL, A4L, 11" × 17"L, 81/2" × 11"L (80 g/m2) (20 lb.)
*1 250 sheets when the optional bridge unit is installed. *2 125 sheets when the optional bridge unit is installed. *3 To place 12" × 18"L size paper use the bypass tray. *4 B5 JISL cannot be shifted. *5 1,500 sheets when stapled.
duced.

Specifications · ❖Staple

Paper size Stapler capacity
A4KL, B5 JISKL, 81/2" × 11"KL, 71/4" × 101/2"KL 50 sheets
(80 g/m2) (20 lb.)
A3L, B4 JISL, 12" × 18"L, 11" × 17"L, 81/2" × 14"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 13"L 30 sheets )
(80 g/m2) (20 lb.)
2 Tray finisher A4KL, B5 JISKL, 81/2" × 11"KL, 71/4" × 101/2"KL 50 sheets
(80 g/m2) (20 lb.)
A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 13"L
(80 g/m2) (20 lb.)
Booklet finisher A4K, B5 JISK, 81/2" × 11"K, 71/4" × 101/2"K 50 sheets
(80 g/m2) (20 lb.)
A3L, B4 JISL, A4L, 11" × 17"L, 81/2" × 14"L, 81/2" × 13"L, 81/2" × 11"L 30 sheets
(80 g/m2) (20 lb.)
When Saddle Stitch function is selected:
A3L, B4 JISL, A4L, 11" × 17"L, 81/2" × 11"L
(80 g/m2) (20 lb.)
happens, remove the copies from the shift tray, and then resume copy- ing.

Paper size and orientation Tray capacity
1000–Sheet finisher A4K, 81/2" × 11"K • 10–50 sheets: 100– 20 sets
A4L, B5 JISKL, 81/2" × 11"L • 10–50 sheets: 50–10 sets
A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L, 12" × 18"L • 10–30 sheets: 50–10 sets
2 Tray finisher Finisher shift tray 1
A4KL, B5 JISKL, 81/2" × 11"KL • 10–50 sheets: 50–10 sets
A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L, 12" × 18"L • 10–30 sheets: 25–8 sets
Finisher shift tray 2
A4K, 81/2" × 11"K • 15–50 sheets: 100– 30 sets
A4L, B5 JISKL, 81/2" × 11"L, 12" × 18"L • 15–50 sheets: 50–15 sets
A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L, 12" × 18"L • 15–30 sheets: 50–25 sets
Booklet finisher Finisher tray
A4K, B5 JISKL,A5K, 81/2" × 11"K 750 sheets or 30 sets
A3L, B4 JISL, A4L, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"L 500 sheets or 30 sets
A3L, B4 JISL, A4L, 11" × 17"L, 81/2" × 11"L • 2–5 sheets: 25 sets
Specifications · Finisher booklet tray

Inch version 81/2" × 11"

2 & 4 holes type 2 holes L A3-A5, 11" × 17"-51/2" × 81/2"
K A4-A5, 81/2" × 11"-51/2" × 81/2"
4 holes L A3, B4 JIS, 11" × 17"
K A4, B5 JIS, 81/2" × 11"
4 holes type 4 holes L A3-A5, 11" × 17"-51/2" × 81/2"
K A4-A5, 81/2" × 11"-51/2" × 81/2"
2 & 3 holes type 2 holes L A3-A5, 11" × 17"-51/2" × 81/2"
K A4-A5, 81/2" × 11"-51/2" × 81/2"
3 holes L A3, B4 JIS, 11" × 17"
K A4, B5 JIS, 81/2" × 11"
Supplementary Informations · Metric version A4 · ❖Punch

Specifications · ❖Duplex · ❖Combine

Depending on the paper size, ratio, and orientation, parts of repeated images may not be copied.
Though the original is set to a different orientation than the paper, the ma- chine will not rotate the image by 90° (Rotate copy).
The width of the erased margin varies depending on the reproduction ratio. If the size of the original is different from sizes listed in the following chart, the erased margin might be shifted: • Metric version

Exposure glass A3L, B4 JISL, A4KL, B5 JISKL, A5KL, 81/2" × 13"L
Auto Document Feeder A3L, B4 JISL, A4KL, B5 JISKL, A5KL, 81/2" × 13"L

Exposure glass 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL
Auto Document Feeder 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 10" × 14"L, 51/2" × 81/2"L

The numbers appear to overlap the copied image in some cases.
When using Combine mode, the date stamp is printed as follows:
When page numbering is used with Combine mode, page numbers are print- ed as follows: • Page Numbering per original: Combined with 1 Sided/2 Sided in the Combine function
Combined with the Magazine or Booklet function

If you combine this function with the Duplex ( Top to Top ) function and se- lect [P1, P2] or [1/n, 2/n], page numbers on the back are printed as follows:
1. Front 2. Back
❖Front Cover, Front/Back Cover
When Combine mode (“1 Sided → 2 Sided”) has been selected, the page num- bers you designate will always be copied onto the front of copies in the same way as Chapters mode.
If you do not copy onto slip sheets, they are excluded from the number of cop- ies counted.
Supplementary Informations · ❖Designate · ❖Slip Sheets









120 GB GB B082-6600
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Copies appear dirty. | The image density is too dark. | Adjust the image density. See p.21 “Adjusting Image Density”. | p.94 |
| Copies appear dirty. | Auto Image Density is not selected. | Adjust the auto density. See p.21 “Adjusting Image Density”. | p.94 |
| The reverse side of an orig- inal image is copied. | The image density is too dark. | Adjust the image density. See p.21 “Adjusting Image Density”. | p.94 |
| The reverse side of an orig- inal image is copied. | Auto Image Density is not selected. | Adjust the auto density. See p.21 “Adjusting Image Density”. | p.94 |
| A shadow appears on cop- ies if you use pasted origi- nals. | The image density is too dark. | Adjust the image density. See p.21 “Adjusting Image Density”. Change the orientation of the origi- nal. Put mending tape on the pasted part. | p.94 |
| The same copy area is dirty whenever making copies. | The exposure glass or the ADF is dirty. | Clean them. See General Settings Guide. | p.94 |
| Copies are too light. | The image density is too light. | Adjust the image density. See p.21 “Adjusting Image Density”. | p.94 |
| Copies are too light. | The paper size is not ap- propriate. | Use the recommended paper. Note ❒ A light copy may result when you use damp or rough grain pa- per. | p.94 |
| Copies are too light. | Toner cartridge is almost empty. | Add toner. See General Settings Guide. | p.94 |
| Parts of the image are not copied. | The original is not set cor- rectly. | Set originals correctly. See p.10 “Placing Originals”. | p.94 |
| Parts of the image are not copied. | An improper paper size is selected. | Select the proper paper size. | p.94 |
| Copies are blank. | The original is not set cor- rectly. | When using the exposure glass, face the originals down. When using the ADF, face them up. See p.10 “Plac- ing Originals”. | p.94 |
| A moiré pattern is pro- duced on copies. R yy yy y y yy y yy y y | Your original has a dot pat- tern image or many lines. | Place the original on the exposure glass at a slight angle. | p.94 |
| Copies are not stapled. | There are jammed staples in the stapler. | Remove jammed staples. See Gener- al Settings Guide. Note ❒ After removing jammed staples, staples might not be ejected the first few times you try to use the stapler. | p.95 |
| Copies are not stapled. | The number of copies ex- ceeds the capacity of the stapler. | Check the stapler capacity. See p.108 “Staple”. | p.95 |
| Copies are not stapled. | Copy paper is curled. | Turn the copy paper over in the tray. | p.95 |
| Staples are wrongly posi- tioned. | Originals are not set cor- rectly. | Check the correct position to place the originals. See p.35 “Staple”. | p.95 |
| You cannot combine sever- al functions. | Selected functions cannot be used together. | Check the combination of functions and make the settings again. Reference p.103 “Combination Chart” | p.95 |
| When sorting, the pages are divided into two blocks. | The memory became full in the middle of sorting and the pages were delivered in two blocks. | You can interrupt copying when the memory becomes full. See p.102 “Memory Full Auto Scan Restart”. | p.95 |
| Paper does not output dur- ing printing with stapling. | When you stop printing while using the staple func- tion, papers not stapled during printing may be left in the staple unit. | Press the {Reset} key and cancel copy settings, including stapling. | p.95 |
| In Double Copies mode, parts of the original image are not copied. | Combination of original and copy paper is not cor- rect. | Select A3L for A4 K originals and A4 for A5 originals. | p.96 |
| In Border, Centre, or Cen- tre/Border mode, parts of the original image are not copied. | You set a wide erased mar- gin. | Make the margin width narrower. You can adjust it between 2–99 mm (0.1"–3.9"). See p.96 “Erase Border Width”and p.96 “Erase Centre Width”. | p.96 |
| In Border, Centre, or Cen- tre/Border mode, parts of the original image are not copied. | Originals are not scanned correctly. | Place the originals correctly. | p.96 |
| In Margin Adjustment mode, parts of the original image are not copied. | You set a wide erased mar- gin. | Set a narrower margin with User Tools. You can set the width be- tween 0–30 mm (0"–1.2"). See p.95 “Front Margin: Left/Right”, p.95 “Front Margin: Top/Bottom”, p.95 “Back Margin: Left/Right”, and p.95 “Back Margin: Top/Bottom”. | p.96 |
| In Margin Adjustment mode, parts of the original image are not copied. | There is a lack of margin space on the opposite side of the binding position. | p.96 | |
| In Image Repeat mode, the original image is not cop- ied repeatedly. | You selected copy paper the same size as the originals, or you did not select the proper reproduction ratio. | Select copy paper larger than the originals. | p.96 |
| In Image Repeat mode, the original image is not cop- ied repeatedly. | Select the proper reproduction ratio. | p.96 | |
| The stamp position is wrong. | The paper orientation is wrong. | Check the paper orientation and stamp position. | p.96 |
| You cannot make a book from Booklet or Magazine mode by folding copies. | You selected a setting (“Open to left”or “Open to right”) that does not match the orientation of originals. | Change the setting. | p.96 |
| When using Combine, parts of the image are not copied. | You specified a reproduc- tion ratio that does not match the sizes of your originals and copy paper. | When you specify a reproduction ra- tio using Manual Paper Select mode, make sure that the ratio matches your originals and the copy paper. Note ❒ Select the correct reproduction ratio before using Combine mode. | p.96 |
| Copies are not in correct or- der. | You placed the originals in the incorrect order. | When placing a stack of originals in the ADF, the last page should be on the bottom. | p.97 |
| Copies are not in correct or- der. | If you place an original on the expo- sure glass, start with the first page to be copied. | p.97 | |
| When using Duplex, copy is made Top/Bottom even hough Left/Right is selected. | You placed the originals in the wrong orientation. | Place the originals in the correct ori- entation. See p.10 “Original Orienta- tion” . | p.97 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.