EN
Lanier logo
Official user manual

Lanier 2002

210 pages·3 MB·Fax Machine·PDF·ENDEFRITNLJA
Lanier 2002
Table of Contents 228 sections Trademark Acknowledgments · Introduction · Introduction to the 2001 and 2002 Units · 2001/2002 Model Differences* · … ShowHide
Trademark Acknowledgmentsp.2Introductionp.9Introduction to the 2001 and 2002 Unitsp.112001/2002 Model Differences*p.11How to Use This Manualp.11Agency Certificationp.11Important Safeguardsp.12Multi-Taskingp.14Machine Componentsp.15Control Panel Layoutp.18Definition of Display Symbolsp.22Basic Operationsp.23Sending a Documentp.25Using Memory Transmitp.25Memory Overflow Transmitp.26Direct (Non-Memory) Transmitp.27Using Handsetp.28Using the HOOK Keyp.29Using Combination Dialp.30Dialing Methodsp.31Receiving a Documentp.32Auto Receivep.32Manual Receivep.33Memory Receive (Memory Lock)p.34Substitute Memory Receivep.35Making Copiesp.36Advanced Facsimilep.39Using the Function Menup.41Broadcastp.42Timer TX (Delay Transmission)p.43Mailbox TXp.44Print Mailbox RXp.45Polling TXp.46Polling RXp.47Continuous Polling RXp.47Relay Initiatep.48Using Combination Dialp.49Using TEL DIRp.50JOURNAL Keyp.51REPORT Keyp.52Reportsp.53Transmit Message Confirmationp.53Manual TX Reportp.53SCHEDULE Keyp.54PIN CODE Keyp.552 SIDED TX. Keyp.56HOOK Keyp.57Facsimile Programmingp.59Accessing The User Program Areap.61Menu Navigationp.61Menu Structurep.62Entering Numbers and Lettersp.64Initial User Datap.65Entering The Date & Timep.65Entering Your Telephone Numberp.65Entering Your User Namep.66Setting Department PWp.66Machine Operationsp.67Setting Your Fax Line Type (PSTN/PBX)p.67Setting the Buzzer (Ring) Volumep.68Setting the Line Monitor (Speaker) Volumep.68Setting the Power Save Modep.69Selecting Remote Monitorp.69Selecting Remote Programp.70Setting the Correct Dialing Type (Tone/Pulse)p.70Document Scan Settingsp.72Resolutionp.72Scan Contrastp.73Print Densityp.73Reduction Copyp.74Rec. Paper Sizep.75Auto Cassette Sel.p.75Dial Registrationp.76One-Touch Keysp.76Speed Dial Keysp.77Group Dial Keysp.78Program Dialp.79Batch TXp.81TX Operationp.83Default TXp.83Closed Network TXp.84Fax Forwardingp.84Headerp.86RX Operationp.87Memory RX Modep.87No. of Ringsp.89Two Page Printp.89Reduction RXp.90Mailbox RXp.90Closed Networkp.91RX Modep.91Footer (Receive Time Print)p.92Continuous Poll RXp.93Line 2 Settingp.95Line 2 Fax No.p.95TX Line Priorityp.95Line 2 Tone / Pulsep.96Reportsp.97Activity Reportp.97Reserv. (Reservation) Reportp.97TX Results Reportp.98RX Results Reportp.98Broadcast Reportp.99Toner Low Reportp.99Other Reports and Listsp.100Setting the Department Number and Password (PW)p.101Assigning a Private Mailbox ID and Password (PW)p.103Editing the RX in Memory Password (PW)p.105PC Printing & Scanningp.107Set Printer (2002 Only)p.109Number of Copiesp.110Symbol Setp.110Font Numberp.111Line Numberp.113Print Fontp.113PCL4p.114GDI Enhancep.115Memory Allocationsp.116Standard Memory Configuration Choicesp.116PCL4 Emulation (2002 only)p.117Connecting to a Computerp.117Setting Up the Computer Application Printer Driverp.118Basic Operationp.118Using the Manual Feed Tray to Printp.118Printing Envelopesp.118Printer Messagesp.119Auto-Select Paper Trayp.119GDI Printer Featurep.120PC Requirementsp.120Connecting to Your PCp.121Installing The Printer Driverp.121Configuring the GDI Print Settingsp.125Printing with your GDI Print Functionp.125Getting Helpp.125Scanning (TWAIN Driver Option)p.126PC Requirements for the TWAIN Optionp.126Installing the TWAIN Driverp.126Scanningp.127Scanner Troubleshootingp.129Class 1 Fax/Modemp.130Class 1 Interfacep.130PC Requirementsp.130Connecting Class 1 to Your PCp.131Installing the PC-Fax Softwarep.131Using Class 1 Modep.131Sending a Fax in Class 1 Modep.132Receiving a Fax in Class 1 Modep.132Scanning in Class 1 Modep.132Printing in Class 1 Modep.133Maintenance & Suppliesp.135Loading the Paperp.137Paper Trayp.137Optional PFU Paper Cassettep.138Clearing Paper Jamsp.140Document Jamsp.140Paper Jamsp.141Changing Toner Cartridgep.145Changing Drum Cartridgep.146Maintenancep.148Cleaning Your Fax Unitp.148Cleaning the Scannerp.148Cleaning the White Rollerp.149Troubleshootingp.151Troubleshootingp.153Error Indication Typesp.153Error Messagesp.154Troubleshooting Tipsp.157Specificationsp.159Physical Specificationsp.161Electrical Specificationsp.161Operational Specificationsp.162Facsimile Specificationsp.164Optional Accessories Specificationsp.164Class 1 Interface (RS-232)p.164PC Interfacep.165LAN Interface (Print Server)(2002 Only)p.165Dual Linep.166Environmental Specificationsp.167Lithium Battery Statementp.167Unpacking & Installationp.169Unpackingp.171Main Carton Contentsp.171Accessories Box Contentsp.172Setting Up Fax Unitp.173Removing the Packing Materialsp.173Installing the Drum Cartridgep.173Installing the Toner Cartridgep.174Installing the Paper Exit Trayp.175Installing the Document Exit Trayp.175Installing the Document Feed Trayp.175Attaching the Power Cord and Telephone Cordsp.176Attaching the PC Cablesp.176Installing the Handsetp.177Loading Paperp.178Turning Power ONp.179Final Checkoutp.180Preparing Your Fax Unitp.180Loading a Documentp.181Setting Up the (Optional) PFUp.182Unpacking the PFUp.182Installing the PFUp.183Loading the Cassettep.184Safety & Agency Certificationsp.187Energy Starp.189Laser Safetyp.189Internal Laser Radiation (For all Users)p.189For United States Usersp.189For Users In Other Countriesp.190FCC Safety Statementp.190FCC Requirementsp.191Label Identificationp.191Type Of Servicep.191Telephone Company Proceduresp.191If A Problem Arisesp.192FCC (For U.S.A. Users)p.193Warning For Setting Headers and Footersp.195User Instructions (For Canada Users)p.196Interference-Causing Equipment Standard (ICES-003 ISSUE 2)p.196Interference-Causing Equipment Standard (ICES-003 ISSUE 2)p.196IC CS-03-Telecommunication Devicep.196Hearing Aid-Compatibility (For U.S.A / Canada Users)p.197Agency Certificationsp.197CE Markp.197Ozone Release (For all Users)p.197Warning Labelsp.198Glossaryp.199Glossaryp.201Indexp.203
Page 1 of the Lanier 2002 user manual — Facsimile
Page 1 · click to enlarge
Page 1

Operator Guide

2001/2002

Lanier 2002 — Operator Guide diagram (page 1)
Fig. 1 · Operator Guide

Facsimile

next level document solutions

Page 2 of the Lanier 2002 user manual — MODEL NUMBER: __________________________
Page 2 · click to enlarge
Page 2

When ordering supplies or requesting service, you will need to provide the model and serial number of your machine.

Please take a moment to enter your model and serial numbers here.

MODEL NUMBER:

SERIAL NUMBER: __________________________

To order supplies, call( )
To request service, call( )

Customer Vision - Our commitment to your

Trademark Acknowledgments Lanier and Customer Vision are registered trademarks of Lanier Worldwide, Inc. Microsoft, MS-DOS, Excel and Windows are registered trademarks of Microsoft Corp. IBM, PC/AT and PS/2 are registered trademarks of International Business Machines Corp. Laser fAX and Hydra Fax are registered trademarks of Wordcraft International Ltd.

As an Energy Star Partner, Lanier Worldwide, Inc. has determined that this product meets the Energy Star guidelines for energy efficiency.

© Lanier Worldwide, Inc. 1999 November

Printed in the U.S.A.

complete satisfaction

Page 3 of the Lanier 2002 user manual — Table of Contents
Page 3 · click to enlarge
Page 3

Table of Contents

Table of Contents

Chapter 1 - Introduction Introduction to the 2001 and 2002 Units 1-1

2001/2002 Model Differences* 1-1 How to Use This Manual 1-1 Agency Certification 1-1 Important Safeguards 1-2 Multi-Tasking 1-4 Machine Components 1-5

Control Panel Layout 1-8 Definition of Display Symbols 1-12

Chapter 2 - Basic Operations Sending a Document 2-1

Using Memory Transmit 2-1 Memory Overflow Transmit 2-2 Dialing Methods 2-7 Receiving a Document 2-8

Auto Receive 2-8 Making Copies 2-12

Chapter 3 - Advanced Facsimile Using the Function Menu 3-1 Broadcast 3-2 Timer TX (Delay Transmission) 3-3 Mailbox TX 3-4 Print Mailbox RX 3-5 Polling TX 3-6 Polling RX 3-7 Continuous Polling RX 3-7 Relay Initiate 3-8 Using Combination Dial 3-9 Using TEL DIR 3-10 JOURNAL Key 3-11 REPORT Key 3-12 Reports 3-13

Transmit Message Confirmation 3-13 Manual TX Report 3-13 SCHEDULE Key 3-14 PIN CODE Key 3-15 2 SIDED TX. Key 3-16 HOOK Key 3-17

Page 4 of the Lanier 2002 user manual — Table of Contents
Page 4 · click to enlarge
Page 4

Table of Contents

Chapter 4 - Facsimile Programming Accessing The User Program Area 4-1

Menu Navigation 4-1 Menu Structure 4-2 Initial User Data 4-5

Entering The Date & Time 4-5 Entering Your Telephone Number 4-5 Entering Your User Name 4-6 Setting Department PW 4-6 Machine Operations 4-7

Setting Your Fax Line Type (PSTN/PBX) 4-7 Setting the Buzzer (Ring) Volume 4-8 Setting the Line Monitor (Speaker) Volume 4-8 Setting the Power Save Mode 4-9 Selecting Remote Monitor 4-10 Selecting Remote Program 4-10 Setting the Correct Dialing Type (Tone/Pulse) 4-11 Document Scan Settings 4-12

Resolution 4-12 Scan Contrast 4-13 Print Density 4-13 Reduction Copy 4-14 Rec. Paper Size 4-14 Auto Cassette Sel 4-15 Dial Registration 4-16

One-Touch Keys 4-16 Speed Dial Keys 4-17 Group Dial Keys 4-18 Program Dial 4-19 Batch TX 4-22 TX Operation 4-23

Default TX 4-23 Closed Network TX 4-24 Fax Forwarding 4-24 RX Operation 4-27

Memory RX Mode 4-27 Two Page Print 4-29 Reduction RX 4-30 Mailbox RX 4-30 Closed Network 4-30 RX Mode 4-32 Footer (Receive Time Print) 4-32 Line 2 Setting 4-35

Line 2 Fax No 4-35 TX Line Priority 4-36 Line 2 Tone / Pulse 4-36 Reports 4-37

Activity Report 4-37 Reserv. (Reservation) Report 4-37 TX Results Report 4-38 RX Results Report 4-38 Broadcast Report 4-39 Toner Low Report 4-39

Page 5 of the Lanier 2002 user manual — Table of Contents
Page 5 · click to enlarge
Page 5

Table of Contents

Setting the Department Number and Password (PW) 1 Assigning a Private Mailbox ID and Password (PW) 1 Editing the RX in Memory Password (PW) 1

Chapter 5 - PC Printing & Scanning Set Printer (2002 Only) 5-1

Symbol Set 5-2 Font Number 5-3 Print Font 5-4 GDI Enhance 5-5 Memory Allocations 5-6

Standard Memory Configuration Choices 5-6 PCL4 Emulation (2002 only) 5-7

Connecting to a Computer 5-7 Basic Operation 5-8 Using the Manual Feed Tray to Print 5-8 Printing Envelopes 5-8 Printer Messages 5-9

Auto-Select Paper Tray 5-9 GDI Printer Feature 5-10

PC Requirements 5-10 Installing The Printer Driver 5-11 Printing with your GDI Print Function 5-14 Getting Help 5-14 Scanning (TWAIN Driver Option) 5-15

PC Requirements for the TWAIN Option 5-15 Installing the TWAIN Driver 5-15 Scanning 5-16 Scanner Troubleshooting 5-17 Class 1 Fax/Modem 5-18

Class 1 Interface 5-18 PC Requirements 5-18 Installing the PC-Fax Software 5-19 Using Class 1 Mode 5-19 Receiving a Fax in Class 1 Mode 5-20 Scanning in Class 1 Mode 5-20

Chapter 6 - Maintenance & Supplies Loading the Paper 6-1

Paper Tray 6-1 Optional PFU Paper Cassette 6-2 Clearing Paper Jams 6-4

Document Jams 6-4 Paper Jams 6-5 Changing Toner Cartridge 6-9 Changing Drum Cartridge 6-10 Maintenance 6-12

Cleaning Your Fax Unit 6-12 Cleaning the Scanner 6-12 Cleaning the White Roller 6-13

Page 6 of the Lanier 2002 user manual — Table of Contents
Page 6 · click to enlarge
Page 6

Table of Contents

Chapter 7 - Troubleshooting Troubleshooting 7-1

Error Indication Types 7-1 Error Messages 7-2 Troubleshooting Tips 7-5

Chapter 8 - Specifications Physical Specifications 8-1 Electrical Specifications 8-1 Operational Specifications 8-2 Facsimile Specifications 8-4 Optional Accessories Specifications 8-4

Class 1 Interface (RS-232) 8-4 LAN Interface (Print Server)(2002 Only) 8-5 Environmental Specifications 8-7 Lithium Battery Statement 8-7

Appendix A - Unpacking & Installation Unpacking A-1

Main Carton Contents A-1 Accessories Box Contents A-2 Setting Up Fax Unit A-3

Removing the Packing Materials A-3 Installing the Drum Cartridge A-3 Installing the Toner Cartridge A-4 Installing the Paper Exit Tray A-5 Installing the Document Exit Tray A-5 Installing the Document Feed Tray A-5 Attaching the Power Cord and Telephone Cords A-6 Attaching the PC Cables A-7 Installing the Handset A-7 Loading Paper A-8 Turning Power ON A-9 Final Checkout A-10

Preparing Your Fax Unit A-10 Loading a Document A-11 Setting Up the (Optional) PFU A-12

Unpacking the PFU A-12 Installing the PFU A-13 Loading the Cassette A-14

Appendix B - Safety & Agency Certifications Energy Star B-1 Laser Safety B-1

Internal Laser Radiation (For all Users) B-1 For United States Users B-1 For Users In Other Countries B-2 FCC Safety Statement B-2 FCC Requirements B-3

Label Identification B-3 Type Of Service B-3

Page 7 of the Lanier 2002 user manual — New Machine Warranty............................................................... 5
Page 7 · click to enlarge
Page 7

Table of Contents

Telephone Company Procedures B-3 If A Problem Arises B-4 FCC (For U.S.A. Users) B-5

Interference-Causing Equipment Standard (ICES-003 ISSUE 2) B-8 Interference-Causing Equipment Standard (ICES-003 ISSUE 2) B-8 IC CS-03-Telecommunication Device B-8 Hearing Aid-Compatibility (For U.S.A / Canada Users) B-9 Agency Certifications B-9

CE Mark B-9 Ozone Release (For all Users) B-9 Warning Labels B-10

Appendix C - Glossary Glossary C-1

Index Terms IX-1

New Machine Warranty 5

Page 8 of the Lanier 2002 user manual — Table of Contents
Page 8 · click to enlarge
Page 8

Table of Contents

Page 9 of the Lanier 2002 user manual — Chapter 1
Page 9 · click to enlarge
Page 9

Chapter 1

Introduction

Page 10 of the Lanier 2002 user manual — Chapter Overview
Page 10 · click to enlarge
Page 10

Chapter Overview

This chapter tells you about safety precautions and shows you the copier’s main components. Contained in this chapter are:

  • Important Safeguards
  • Multi-Tasking
  • Machine Components
  • Control Panel
  • Definition of LCD Symbols

Introduction

Page 11 of the Lanier 2002 user manual — Agency Certification
Page 11 · click to enlarge
Page 11

Introduction to the 2001 and 2002 Units

Introduction to the 2001 and 2002 Units

The 2001 is a fully featured Facsimile unit. It has several options that allow its capabilities to be increased even more. The 2002 is a multi-function device that in addition to the Fax capability, allow you to Print, Scan and Copy.

2001/2002 Model Differences*

Item20012002 PFU TrayOptionalOptional TEL/FAX ModeYesNo Page Memory1 MB6 MB Dual Line ModeOptionalOptional PrintingNoYes ScanningNoYes

* Items listed above are for the standard configuration. For information on other options, refer to the Specifications Chapter.

How to Use This Manual

This manual explains the functions and operation of the Lanier 2001 and 2002 units. It also gives some troubleshooting tips as well as general precautions to be observed during operations. To ensure the best performance and effective use of your unit, please read this manual carefully from cover to cover. After you have read the manual, keep it near your Fax unit for handy reference. It should be helpful in solving any operational questions you may have. This manual is written to cover the base machine with all the options installed. If your unit does not have these options installed, just skip that section. If you choose to upgrade your unit in the future, you will already have the necessary information. Call your Sales or Service Representative to order options and schedule their installation.

Agency Certification

Your 2001/2002 unit complies with FCC rules, DOC requirements, and other agency certification requirements. Refer to the Appendix section of this manual for details. These units are Energy Star qualified.

Introduction 1 - 1

Page 12 of the Lanier 2002 user manual — Important Safeguards
Page 12 · click to enlarge
Page 12

Important Safeguards

Important Safeguards

Always follow these important safeguards:

1 Read all of these instructions before using your unit.

2 Do not use this unit near water; for example, near a bath tub, sink or swimming pool.

3 Avoid using the telephone during an electrical storm. There may be a remote risk of electric shock from lighting.

4 Do not use the telephone to report a gas leak in the vicinity of this unit.

5 Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instruction.

6 Plug the power cord only into a 3-conductor (grounded) outlet rated for at least 15 amperes.

  • Never ground the power cord to a gas pipe or a water pipe.
  • Keep the power cord away from hot surfaces.
  • Avoid using an extension cord if at all possible. If you must use an extension cord, use only a 3-conductor cord rated for at least 15 amperes. Cords rated for less might overheat and become a fire hazard.
  • Do not operate your unit if any part of it is damaged, or if any part has been dropped, until it is checked by a qualified technician.
Lanier 2002 — Important Safeguards diagram (page 12)
Fig. 2 · Important Safeguards
  • 7 Do not install your unit in areas that are:
  • Damp or humid
  • Exposed to direct sunlight
  • Extremely dusty
  • Poorly ventilated
  • Subject to extreme temperature or humidity changes. For example, don’t locate your copier near an air conditioner or heater.

8 Install your unit with space around it to provide adequate ventilation.

9 Do not place the unit near a television or radio. If the unit is too close it may inter- fere with the reception.

1. 2 Introduction
Page 13 of the Lanier 2002 user manual — Important Safeguards
Page 13 · click to enlarge
Page 13

Important Safeguards

10 Place your unit on a firm, level surface.

11 Do not place heavy objects on the ADF (Automatic Document Feeder) or the Exit Tray.

12 Do not disassemble your unit or try to repair it yourself, other than as instructed in this Operator Guide. Call an Authorized Service Center for all necessary repairs. Incorrect assembly can cause electrical hazards and possible damage to the machine.

Introduction 1 - 3

Page 14 of the Lanier 2002 user manual — Multi-Tasking
Page 14 · click to enlarge
Page 14

Multi-Tasking

Multi-Tasking

The 2001 and 2002s can perform multiple operations at the same time. One operation can run in the foreground, while another runs in the background. For example, you can scan, copy, or print documents into memory for later transmission while receiving a fax.

Operation Concurrent Operation Result

The received fax is stored in memory, and prints once copy operation is complete.

GDI/PCL4 Printing (2002 only)

Print job is stored in memory, and prints once copy operation is complete.

Faxing begins while copying continues.

PC-Fax Transmission or Reception

Faxing begins while copying continues.

The Copy job will be stored in memory, then printed out when reception (RX) is complete.

GDI/PCL4 Printing (2002 only) Fax Transmission

Print document during reception.

Scans document into memory for transmission.

The available memory is shared by both jobs and their operations happen simultaneously.

GDI/PCL4 Printing (2002 only)

The document will be printed from the PC during Fax operation.

Copy operation starts by scanning document into memory, and prints as fax is being transmitted.

Parallel Port Printing (2002 only)

Print operation occurs while PC is receiving the fax.

TX works when PC-Fax is complete. Scans document into memory for transmission.

Copy operation starts by scanning document into memory first, and prints as fax is being transmitted.

Parallel Port Printing (2002 only)

Parallel Port can be used for printing during PC- FAX operation.

Scans document into memory for transmission.

1. 4 Introduction
Show 11 more labels / short text on this page
Copy Fax Reception · Memory Fax transmission · Fax Reception Copy · Fax Transmission · Copy · PC-Fax Reception · Copy · Fax Transmission · PC-Fax Transmit · Copy · Fax Transmission
Page 15 of the Lanier 2002 user manual — Machine Components
Page 15 · click to enlarge
Page 15

Machine Components

Machine Components

External Components: Front

1 Document Exit Tray

This tray catches the original document after it passes through the scanner.

You can load up to 250 sheets of Letter- size, A4, or Legal-size paper into the standard Tray.

2 Control Panel / Scanner Cover

You can add another 500 sheets with the optional Paper Feed Unit (PFU).

The controls on the panel perform the various faxing, copying, and printing functions. Lift this panel lifts to remove document feed jams.

6 Bypass Feed Tray

You can feed single sheets of special types of paper. i.e. pre-printed letterhead & envelopes (2002).

3 Document Feed Tray

Load your document face down on this tray for faxing or copying.

7 Paper Exit Tray

This Tray catches the paper after printing.

4 Document Alignment Guides

Adjust these Guides to fit the width of your original documents.

Lanier 2002 — Machine Components diagram (page 15)
Fig. 3 · Machine Components

Introduction 1 - 5

5 Paper Tray

Page 16 of the Lanier 2002 user manual — Machine Components
Page 16 · click to enlarge
Page 16

Machine Components

External Components: Rear

8 AC Power Connector

13 Serial Connector (RS232)

The AC Power Cord plugs in here.

Provides connection between this unit and a host computer for Class 1 PC faxing and Twain-compliant scanning. This interface can also be used for printing.

9 Main ON/OFF Switch

Use to turn the your unit ON and OFF.

10 Telephone Line Connector

Plug the telephone cable from this connector into the wall socket of the telephone line.

14 Network Connector (Optional NIC Card)

Provides connection between the unit and the Network.

11 Telephone Hand Set Connector -or- External Line

15 Dual Line Connector (Optional)

Use this connector to plug in the telephone cord from the telephone set.

Plug the telephone cable from this connector into the wall socket for the second line.

Provides connection between this unit and a host computer for GDI printing or PCL4 or 5e printing.

Lanier 2002 — Machine Components diagram (page 16)
Fig. 4 · Machine Components
1. 6 Introduction

12 Parallel Connector

Page 17 of the Lanier 2002 user manual — Machine Components
Page 17 · click to enlarge
Page 17

Machine Components

External Components: Internal and Optional

16 Top Cover / Cover Release Buttons

Press these two buttons to open the Top Cover to check and clear paper jams, to change the Toner and Drum, or to clean the interior of the unit.

This Drum Cartridge transfers toner to the paper.

19 Paper Feed Unit (PFU) (Optional)

When installed, it permits your unit to print up to 750 uninterrupted pages without reloading paper. (750 pages of standard weight Letter/A4 size paper.

The Toner Cartridge contains the toner particles used in imaging.

Lanier 2002 — Machine Components diagram (page 17)
Fig. 5 · Machine Components

Introduction 1 - 7

18 Drum Cartridge · 17 Toner Cartridge

Page 18 of the Lanier 2002 user manual — HOOK
Page 18 · click to enlarge
Page 18

Machine Components

Control Panel Layout

1 3 2 4 5 6

2 SIDED TX.

PHOTO FINE STD EX-FINE LIGHT NORM

DARK

AUTO RX. MEM. TX. ALARM

RESOLUTION

PHOTO

TYPE ORG.

SCHEDULE

JOURNAL

REPORT

MEM. TX.

FUNCTION

PROGRAM

/2 SIDED TX. YES NO CODE PIN DELETE

COPY

SPEED DIAL

ABC

DEF

A

B

D

E

F

G

H

TEL DIR

GHI

JKL

MNO

STOP

J

K

M

N O

P

REDAIL /PAUSE

PQRS

TUV

WXYZ

S R Q

V W T U

START

28 61 29 62 30 63 31

HOOK

OPER

Y

Z

1. Display The LCD Display provides you with instructions and information about fax, copying, printing, programming and operational functions.
2. Resolution Keys Press this key to select the desired resolution for scanning: Standard: Use for normal documents. This is the default. Fine: Use for documents with fine lines or characters. Super Fine: Use for very fine maps, drawings or extremely detailed originals. Photo: Use for photographs or shaded drawings.
3. Original Type Key Press this key to select the type of original you are using: Normal: Use this for most of the regular documents. Light: Use for documents with very fine or light characters. Dark: Use for documents that are dark.
4. Memory TX Key/ Light

Press this Key to turn Memory TX transmission ON or OFF. When the Memory TX light is ON, it signifies that documents will be stored to memory for transmission. ON: Memory TX Mode OFF: ADF TX Mode

5. Auto RX Light This light indicates the receiving mode of the Facsimile: ON: The facsimile will receive documents automatically. OFF: The facsimile will receive documents manually.
6. Alarm Light The ALARM Light illuminates if there is a problem with the unit such as paper jam. After the problem has been corrected or when the STOP Key is pressed, the light turns OFF.
1. 8 Introduction
Show 9 more labels / short text on this page
< · > · < · < · + · -/& · ¡¯ · # · Panel Description
Page 19 of the Lanier 2002 user manual — HOOK
Page 19 · click to enlarge
Page 19

Machine Components

7 8 9 10 15

11 14 13 12

2 SIDED TX.

PHOTO FINE STD EX-FINE LIGHT NORM

DARK

AUTO RX. MEM. TX. ALARM

RESOLUTION

PHOTO

TYPE ORG.

SCHEDULE

JOURNAL

REPORT

MEM. TX.

/2 SIDED TX. YES NO CODE PIN DELETE

FUNCTION

PROGRAM

COPY

SPEED DIAL

ABC

DEF

A

B

D

E

F

G

H

TEL DIR

GHI

JKL

MNO

STOP

J

K

M

N O

P

REDAIL /PAUSE

S R Q

V W T U

PQRS

TUV

WXYZ

START

28 61 29 62 30 63 31

HOOK

Y

Z

OPER

7. Function Key The FUNCTION Key allow access to the Function Menu (Broadcast, Timer TX, Mailbox TX, Polling TX, Polling RX, Relay Broadcast, Cancel Reservation). Set Functions by pressing the FUNCTION Key first and then selecting the desired function using numeric keys or the FUNCTION Key.
8. PROGRAM Key Press the PROGRAM Key to enter the set menu and program your desired function using either numeric keys or the arrow on the display.
9. YES Key The YES Key is used to accept the selections made under PROGRAM and FUNCTION menus.
10. NO Key The NO Key is used to reject the selections made under the PROGRAM and FUNCTION menus.
11. Pin Code Key This key is used to input personal identification number for some telephone systems when you dial an outside number.
12. 2-Sided TX/Delete This key a dual purpose key. It controls 2-sided TX scanning. When in a Program mode, it is used to Delete an entry.
13. Schedule Key Press this key to view the transaction in memory file, such as memory transmission or polling.
14. Journal Press this key to view the transaction result the same as in an activity report. This shows the session number, remote ID or dial number and result.
15. Report Key This key is used to choose your desired report, press YES to print out the report if you need.
16. Arrow Keys

Used to move cursor to the right or left one position or to scroll through the menu.

Use the Key to enter ITU-T Sub-address in setting One-Touch or Speed Dial Keys.

Introduction 1 - 9

Show 10 more labels / short text on this page
< · > · < · < · + · -/& · ¡¯ · # · Panel Description · ( )
Page 20 of the Lanier 2002 user manual — Machine Components
Page 20 · click to enlarge
Page 20

Machine Components

Lanier 2002 — Machine Components diagram (page 20)
Fig. 6 · Machine Components
17. One-Touch Keys The One-Touch Keys are used to store frequently dialled numbers. Any of the Keys can be assigned as One-Touch Keys or Group Dial Keys. In addition, the last eight keys can be used as Program Keys. Each Group Key can hold up to 50 One-Touch or Speed Dial numbers.
18. The “+” Key Used to register a combination dial in a One-Touch or Speed Dial Key, This symbol must follow the initial number and be followed by a number stored in the One-Touch, Speed Dial Key or entered via the Ten-Key Pad.
19. Speed Dial Key Use this to initiate speed dialling. Press the SPEED DIAL key and your three-digit code to start a transmission.
20. TEL DIR Key Use this key to find, by name, fax numbers previously stored.

21. Redial/Pause Key Redial: Press this key to redial the last telephone number called. Pause: Press this key to insert a pause in the number being stored. When you press this key, a “P” is inserted within a number causing a 2.5 second delay when dialing. This is useful if you must dial a prefix, such as 9 to pause briefly in order to access an outside telephone line. (A “P” after a series of numbers adds 10 seconds to the normal time the machine waits for a remote receiver to answer a call.)

22. Hook Key Press this key to switch the unit to the telephone line for direct (manual) dial from the machine’s keypad. When pressed first, it also allows you to hear the dialing when using One-Touch, Speed Dial, etc.
23. “*” Key Press the “*” Key for tone dialing while your unit is set for pulse dialing. (This key is only effective when the HOOK Key is used.)
1. 10 Introduction

Panel Description

Page 21 of the Lanier 2002 user manual — Machine Components
Page 21 · click to enlarge
Page 21

Machine Components

24. Keypad These twelve keys work for the internal telephone in the fax unit just like the keypad on regular touch tone phones. You can use the keypad to dial a remote unit directly or to assign codes and telephone numbers to One-Touch and Speed Dial locations.
25. “#” Key Press the “#” Key to access internal line or PSTN line when your unit is set for use over a PBX line.
26. Copy Key Press the COPY Key to initiate copying documents that are loaded on the Document Feed Tray.
27. STOP Key Use this key to stop copying, transmitting, dialling waiting to dial or scanning. You can also press the STOP to return from any operation mode back to the standby status.
28. START Key Press the START Key to begin transmitting, scanning, copying or manual fax reception.

Introduction 1 - 11

Panel Description

Page 22 of the Lanier 2002 user manual — Machine Components
Page 22 · click to enlarge
Page 22

Machine Components

Definition of Display Symbols

The LCD Display shows the date, time of day, amount of memory available for use, fax numbers, fax conditions and other information by means of either a message or graphic. The follow table is a list of icons that can appear on the LCD Display.

Signifies a fax or phone number.

Shown while the remote fax number is being rung.

Prompts you to enter a fax number.

Shown while the user’s local fax is being rung.

Indicates the pause function is set into the destination’s fax number. Example 0P412641267

Shows the number of pages. Example: A single page.

Indicates when the Internal PBX function is set into the destinations’s fax number.

Shown while a document is being transmitted to the other party.

Indicates when the Sub Address is set into the destination’s fax number. Example: 4126412 :8108

Shown while a document is being received from the other party.

Indicates that a polling transmission function has been stored in memory.

Indicates that a document to be transmitted by the timer transmission function has been stored in memory.

Indicates when the External PBX to PSTN function is set into the destination’s fax number

1. 12 Introduction
Page 23 of the Lanier 2002 user manual — Chapter 2
Page 23 · click to enlarge
Page 23

Chapter 2

Basic Operations

Page 24 of the Lanier 2002 user manual — Chapter Overview
Page 24 · click to enlarge
Page 24

Chapter Overview

This chapter explains the Basic Operations of the unit. It covers the basic fax operations and how to make a copy.

The procedures in this chapter assume that the necessary One-Touch Keys and other remote unit information has been programmed. If your unit has not been programmed, you will want to turn to Chapter 4 Programming and enter this data.

Basic Operations

Page 25 of the Lanier 2002 user manual — 3 Use the TYPE ORG. Key to select the desired contrast:
Page 25 · click to enlarge
Page 25

Sending a Document

Sending a Document

Using Memory Transmit

Since your fax unit provides multi access capabilities, you can scan documents into memory for transmission, even if your unit is in the process of transmitting data from memory, receiving data or printing a file from the PC.

1 Place your document face down on the Document Feed Tray.

NOV.07 12:34 100% -SET DOC. FACE DOWN-

2 Adjust the Document Side Guides to the edges of the document.

Lanier 2002 — NOV.07 12:34 100% -SET DOC. FACE DOWN- diagram (page 25)
Fig. 7

3 Use the TYPE ORG. Key to select the desired contrast:

Lanier 2002 — 3 Use the TYPE ORG. Key to select the desired contrast: diagram (page 25)
Fig. 8 · 3 Use the TYPE ORG. Key to select the desired contra…

Basic Operations 2 - 1

Page 26 of the Lanier 2002 user manual — Sending a Document
Page 26 · click to enlarge
Page 26

Sending a Document

4 Use the RESOLUTION Key to select the desired resolution:

Lanier 2002 — Sending a Document diagram (page 26)
Fig. 9 · Sending a Document

Standard Documents with standard size characters, such as typed documents.

Fine Documents with smaller size characters, like newsprint. (Copy Default)

Extra Fine Documents with very fine or light characters.

5 If you are sending a photograph, press the PHOTO Key for best results.

6 Enter the remote Fax number using the numeric Key Pad.

  • The unit scans the document into memory and sends it to the location you selected.
  • The unit automatically returns to standby mode when finished transmitting.

7 To stop a transmission, press the STOP Key.

Memory Overflow Transmit works the same as Memory Transmit with one special exception. When your unit senses it will run out of memory of the next page of your document is scanned, it will stop and ask if you wish to send what is already stored in memory. When you answer YES, it dials the number and sends those pages. When sufficient memory has been freed up, it begins scanning again. It then places a second call automatically and sends the remainder of the pages. On a report all of this activity is logged as one session.

2. 2 Basic Operations
Page 27 of the Lanier 2002 user manual — TX CANCEL? YES/CONTINUE=NO
Page 27 · click to enlarge
Page 27

Sending a Document

Direct (Non-Memory) Transmit

Direct Transmission, from the Automatic Document Feeder (ADF), bypasses the unit’s memory. This can be used to transmit a fax when memory is full. If you anticipate that there might not be enough memory to scan a particular document into memory (for example, lengthy documents), transmit it directly form the ADF. Be sure the LED for Memory TX is OFF before starting transmission.

1 Place your document face down on the Document Feed Tray.

2 Adjust the Document Side Guides to the edges of the document.

3 Use the TYPE ORG. Key to select the desired contrast.

4 Use the RESOLUTION Key to select the desired resolution.

5 Press the MEM.TX Key to turn OFF the memory use.

OTO LIGHT NORM

DARK

AUTO RX. MEM. TX. AL

OTO

TYPE ORG.

RNAL

REPORT

MEM. TX.

6 Enter the remote Fax number one of the following methods: Speed Dial, One-Touch, Redial or manually using the 10-Key Pad.

ENTER FAX NO. or FUNCTION

  • The unit scans the first page of the document and sends it.
  • This continues until the last page has been sent.
  • The unit automatically returns to standby mode when finished transmitting.

7 To stop a transmission already in progress, press the STOP Key.

TX CANCEL? YES/CONTINUE=NO

Basic Operations 2 - 3

> · < ·

Page 28 of the Lanier 2002 user manual — TX CANCEL? YES/CONTINUE=NO
Page 28 · click to enlarge
Page 28

Sending a Document

Using Handset

You can fax a document by dialing the number using the telephone handset. This function can be used if you need to talk to the receiving party before transmission. When dialing manually, documents will be transmitted without being stored in memory.

1 Place your document face down on the Document Feed Tray.

ENTER FAX NO. or FUNCTION

2 Adjust the Document Side Guides to the edges of the document.

3 Use the TYPE ORG. Key to select the desired contrast:

4 Use the RESOLUTION Key to select the desired resolution:

5 Lift the Handset and dial the number on the Handset.

“TALKING*

6 When the connection is made with the dialed number, press the START Key and hang up the Handset.

  • The unit scans and sends the document.
  • The unit automatically returns to standby mode when finished truncating.

7 To stop a transmission already in progress, press the STOP Key.

TX CANCEL? YES/CONTINUE=NO

2. 4 Basic Operations

(7776660000)

Page 29 of the Lanier 2002 user manual — (7776665555) -PUSH START KEY-
Page 29 · click to enlarge
Page 29

Sending a Document

Using the HOOK Key

Use the HOOK dial sequence when it is necessary to listen to the “Handshake”. This is an important troubleshooting aid to see if a transmission fault is phone related or not. It is possible to dial a location using any combination of TEN-Key, One Touch Dial, or Speed Dial Directories.

1 Place your document face down on the Document Feed Tray.

2 Adjust the Document Side Guides to the edges of the document.

3 Use the TYPE ORG. Key to select the desired contrast:

4 Use the RESOLUTION Key to select the desired resolution:

5 Press the HOOK Key.

TEL DIR

GHI

JKL

MNO

REDAIL /PAUSE

PQRS

TUV

WXYZ

6 Enter the remote fax number using one of the entry methods.

HOOK

OPER

7 listen until the remote fax unit answers, then press the START Key.

(7776665555) -PUSH START KEY-

8 To stop a transmission already in progress, press the STOP Key.

Basic Operations 2 - 5

¡¯ · #

Page 30 of the Lanier 2002 user manual — 3 Use the TYPE ORG. Key to select the desired contrast:
Page 30 · click to enlarge
Page 30

Sending a Document

Using Combination Dial

This is used when the number exceeds the 30 digit limit for a single location. The number is split between two locations and the two are automatically linked when the first of the two is used. It is possible to input dialing numbers continuously. You can enter another One-Touch, Speed Dial or Ten Key followed by the combination dial numbers (phone numbers last digits is ‘+’ in One Touch or Speed Dial Key). The telephone number limit is 30 digits.

1 Place your document face down on the Document Feed Tray.

2 Adjust the Document Side Guides to the edges of the document.

3 Use the TYPE ORG. Key to select the desired contrast:

4 Use the RESOLUTION Key to select the desired resolution:

5 Press a One-Touch Key. • The One-Touch number should have a “+” at the end indicating an additional Key has been programmed to extend the length of the number.

6 Press the second One-Touch key containing the additional numbers and press START.

  • The unit scans the document into memory and sends it to the location you selected.
  • The unit automatically returns to standby mode when finished transmitting.

7 To stop a transmission, press the STOP Key.

2. 6 Basic Operations
Page 31 of the Lanier 2002 user manual — Dialing Methods
Page 31 · click to enlarge
Page 31

Dialing Methods

Dialing Methods

You can use the following methods to dial a remote facsimile number from your unit.

Use this setting for this

1. Key Pad Dial Dial the number of the remote facsimile using the numeric keypad. You can also use the Arrow Key to correct any mistakes. (A maximum of 30 digits are allowed, including the “PAUSE” (P).
2. One Touch Dial Press a ONE TOUCH Key. Its number will be displayed and the unit scans the document and dials the number automatically. See the Advanced Operations.
3. Speed Dial Press the SPEED DIAL Key and enter a three-digit dial number from the keypad. The Speed Dial number is shown on the display. The unit scans the document and dials the number automatically.
4. Group Dial Press a ONE-TOUCH Key. Any One-Touch Key can be programmed for Group Dialing. The Group Name is shown on the display. The unit scans the document and dials the numbers automatically.
5. Program Dial Several transmission functions can be programmed in any of the last eight One-Touch Keys. To utilize these functions, press the corresponding One-Touch Key. For example: if you want to set up an after-hours broadcast which is performed regularly, you can register the necessary functions in a Program Dial Key.
6. Using Combination Dial

If the One-Touch or Speed Dial phone number displays a “+” as the last character, additional numbers are necessary to complete the dialing. The additional numbers may be stored in a One-Touch or Speed Dial location, or may be entered using the key pad.

7. Using the TEL/DIR Key

The TEL/DIR function lists the One Touch and Speed Dial locations stored in this unit. The LIST function enables you to scroll through the list. The SEARCH functions enables you to search a location alphabetically or numerically.

8. Using the “#” Key In most PBX applications, a prefix is necessary ahead of the outside phone number in order to access an outside line. Once this prefix number has been programmed into the machine, pressing the “#” Key automatically enters it in the string.

Basic Operations 2 - 7

Page 32 of the Lanier 2002 user manual — (CHICAGO) 100% -SET DOC. FACE DOWN-
Page 32 · click to enlarge
Page 32

Receiving a Document

Receiving a Document

Use automatic receiving when you want your fax to automatically receive faxes without any intervention from you.

Auto Receive

1 Make sure your unit is ready to receive.

NOV.07 12:34 100% -SET DOC. FACE DOWN-

  • When your unit rings, the LCD shows this message.

( ) 100% -SET DOC. FACE DOWN-

  • If the sending location is recognized, the blank is filled in with the name or telephone number of the location.
  • When the transmission is complete this message is displayed. The number at the end of the second line indicates the number of pages sent.
  • When the document starts to print, the following message is displayed. The return of the second line shows that other operations such as sending a Fax or making a copy are now available.
  • When the final page prints, the display shows the following message. The number shows the number of pages printed

(CHICAGO) 100% -SET DOC. FACE DOWN-

*RX COMPLETE* CHICAGO 20P

*PRINT DOC* 90% -SET DOC. FACE DOWN-

*PRINT COMPLETE* 20P

2. 8 Basic Operations
Page 33 of the Lanier 2002 user manual — (CHICAGO) 100% -SET DOC. FACE DOWN-
Page 33 · click to enlarge
Page 33

Receiving a Document

Manual Receive

In the manual receive mode, you can talk to the caller and start the receive the document after the conversation is over.

1 When your unit rings, answer the phone.

NOV.07 12:34 100% -SET DOC. FACE DOWN-

2 If it is evident that it is a fax transmission, press the START Key on your unit and then replace the phone on the cradle.

*TALKING*

  • An intermittent tone after picking up the handset indicates a fax call.
  • When your unit recognizes the signal as a fax call, the LCD shows this message.

( ) 100% -SET DOC. FACE DOWN-

  • If the sending location is recognized, the blank is filled in with the name or telephone number of the location.
  • When the transmission is complete this message is displayed. The number at the end of the second line indicates the number of pages sent.
  • When the document starts to print the following message is displayed. The return of the second line shows that other operations such as sending a Fax or making a copy are now available.
  • When the final page prints, the display shows the following message. The number shows the number of pages printed.

(CHICAGO) 100% -SET DOC. FACE DOWN-

*RX COMPLETE* CHICAGO 20P

*PRINT DOC* 90% -SET DOC. FACE DOWN-

*PRINT COMPLETE* 20P

Basic Operations 2 - 9

Page 34 of the Lanier 2002 user manual — *PRINT COMPLETE*
Page 34 · click to enlarge
Page 34

Receiving a Document

Memory Receive (Memory Lock)

This option saves all incoming faxes into memory. To access and print these documents, you must enter a password.

1 With your unit in a ready position, the following message appears.

<<M-RX>> 100% -SET DOC. FACE DOWN-

  • When your unit rings, the LCD shows this message.

( ) 100% -SET DOC. FACE DOWN-

  • If the sending location is recognized, the blank is filled in with the name or telephone number of the location.
  • When the transmission is complete this message is displayed. The number at the end of the second line indicates the number of pages sent.
  • The document ‘prints’ into memory.

(CHICAGO) 100% -SET DOC. FACE DOWN-

*RX COMPLETE* CHICAGO 20P

<<M-RX 10P>> 80% -SET DOC. FACE DOWN-

  • When the final page ‘prints’, the display shows the following message. The number shows the number of pages printed.

*PRINT COMPLETE* 20P

2 To print the document in memory, press the FUNCTION Key.

3 Scroll to the Memory RX Print memu.

4 Enter your Memory RX Password and press YES.

MEMORY RX PW=_ OK=YES (DEL=NO)

5 If you enter the wrong PW you are prompted and then given an opportunity to enter the correct PW number.

*WRONG PW*

6 When the contents of your Mailbox has printed, you are prompted that printing is complete.

*PRINT COMPLETE*

2. 10 Basic Operations
Page 35 of the Lanier 2002 user manual — *PRINT COMPLETE* 15P
Page 35 · click to enlarge
Page 35

Receiving a Document

Substitute Memory Receive

If the facsimile unit should encounter any of the following situations, it will switch from direct reception mode to memory reception mode.

  • Machine runs out of paper
  • Machine runs out of toner
  • Printer Cover is open
  • Recording Paper Jam
  • Machine trouble

1 With your unit in a ready position, the following message appears.

NOV.07 12:34 100% -SET DOC. FACE DOWN-

  • When your unit rings, the LCD shows this message.

( ) 100% -SET DOC. FACE DOWN-

  • If for any of the above reasons your unit cannot receive and print the message, an error message is displayed.

*MEMORY RX* 15P RECORDING PAPER JAM

2 Take whatever actions are required to clear the error. • When the error is removed, the unit returns to normal operation and starts printing the documents stored in memory.

*PRINT DOC. 80% -SET DOC. FACE DOWN-

  • When the final page prints, the display shows the following message. The number shows the number of pages printed.

*PRINT COMPLETE* 15P

Basic Operations 2 - 11

Page 36 of the Lanier 2002 user manual — SCHEDULE
Page 36 · click to enlarge
Page 36

Making Copies

Making Copies

With your facsimile unit, you can make from 1 to 99 high quality copies of an original document. The Document Feeder can hold up to 50 originals.

Procedure

1 Place your document face down on the Document Feed Tray.

2 Adjust the Document Side Guides to the edges of the document.

3 The LCD Message Display indicates the following:

T=ENTER FAX NO. or FUNCTION

4 Use the TYPE ORG. Key to select the desired contrast:

  • Use NORM for regular documents.
  • Use LIGHT for documents with very fine or light characters.
  • Use DARK for documents that are dark.

PHOTO FINE EX-FINE LIGHT NORM

DARK

AUTO MEM. TX.

OLUTION

PHOTO

TYPE ORG.

EDULE

JOURNAL

REPORT

MEM. TX.

5 Use the RESOLUTION Key to select the desired resolution:

  • Use STD (Standard) for documents with standard size characters, such as typed documents.
  • Use FINE for documents with smaller size characters, like newsprint.
  • Use EX-FINE for documents with very fine characters.

2 SIDED TX.

PHOTO FINE STD EX-FINE LIGHT NORM

DARK

RESOLUTION

PHOTO

TYPE ORG.

SCHEDULE

JOURNAL

REPORT

DELETE

/2 SIDED TX. E

6 Use PHOTO for documents such as photos that have a gray scale. PHOTO may be used in combination with Original Types and Resolution Keys.

2. 12 Basic Operations
Show 7 more labels / short text on this page
< · > · < · < · < · > · <
Page 37 of the Lanier 2002 user manual — Making Copies
Page 37 · click to enlarge
Page 37
Lanier 2002 — Making Copies diagram (page 37)
Fig. 10 · Making Copies

9 Enter the number of copies you need using the Numeric Keypad.

10 If you have entered more than “1” as your quantity, press the YES Key to sort the set, or press START to STACK the sets.

Lanier 2002 — Making Copies diagram (page 37)
Fig. 11 · Making Copies

STACK (Default) Copies the original document according to the page number order. Example: If you are making two copies of pages 1 through 4, the copies are produced in this order: 1, 1, 2, 2, 3, 3, 4, 4

SORTER Copies the original document according to sort order. Example: If you are making two copies of pages 1 through 4, the copies are produced in this order: 1, 2, 3, 4, 1, 2, 3, 4

  • The unit scans the document into memory and then makes copies.
  • The unit automatically returns to standby mode.

Basic Operations 2 - 13

Page 38 of the Lanier 2002 user manual — Making Copies
Page 38 · click to enlarge
Page 38

Making Copies

Notes:

2. 14 Basic Operations
Page 39 of the Lanier 2002 user manual — Chapter 3
Page 39 · click to enlarge
Page 39

Chapter 3

Advanced Facsimile

Page 40 of the Lanier 2002 user manual — Chapter Overview
Page 40 · click to enlarge
Page 40

Chapter Overview

This chapter contains information about additional facsimile features available on your fax unit. A number of features are accessible through display prompts or by pressing FUNCTION Memu key. The step-by-step explanations detail the steps using the function and keypad keys.

You may press STOP at any point to cancel selections and return to standby.

The advanced features in this chapter include the following:

  • Broadcast
  • Polling Transmission
  • Delay Transmission
  • Polling Receive
  • Mailbox Transmission
  • Relay Initiate
  • Mailbox Receive
  • Combination Dial

It also covers the use of the following Control Panel Keys:

  • TEL DIR Key
  • PIN CODE Key
  • JOURNAL Key
  • 2 SIDED TX. Key
  • REPORT Key
  • HOOK Key
  • SCHEDULE Key

Advanced Facsimile

Page 41 of the Lanier 2002 user manual — FUNCTION SEL. 1-7 OR FUNCTION
Page 41 · click to enlarge
Page 41

Using the Function Menu

Using the Function Menu

The FUNCTION Key is used to access the most often used fax functions. Listed below are the menus you will encounter.

FUNCTION 1 BROADCAST

2 TIMER TX

3 MAILBOX TX

4 PRINT MAILBOX RX

5 POLLING TX

6 POLLING RX

7 RELAY INITIATE

1 To access these functions, press the FUNCTION Key.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

  • 2 To select an option, perform one of the following:.
  • Press the number of the item you want.
  • OR, Press FUNCTION a second time and use the arrow keys to go the menu item you want.
  • OR, Press FUNCTION continually until you reach the menu item you want.

FUNCTION SEL. 1-7 OR FUNCTION

Advanced Facsimile 3 - 1

Page 42 of the Lanier 2002 user manual — NO.001=_ OK=YES (DEL=NO)
Page 42 · click to enlarge
Page 42

Broadcast

Broadcast

The Broadcast feature allows you to send the same document to multiple locations in the same session. The facsimile will scan the document into memory and transmit it sequentially to different destinations.

The facsimile can broadcast to destinations consisting of all One-Touch Dials, 100 Speed Dials and 16 manually dialed numbers.

If you frequently send documents to the same multiple location, you can set up a Group Dial Key to automatically broadcast to these locations. See the Facsimile Programming Chapter for more info.

Procedure

1 Select the Original Type, Resolution if necessary and place your document in the Document Feeder face down.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Press the FUNCTION Key and enter 1 to select the Broadcast function.

FUNCTION SEL. 1-7 OR FUNCTION

3 The following message appears briefly to confirm your selection.

1 BROADCAST

4 Enter the Broadcast location number. This can be a One-Touch Key, a Speed Dial Key, a Group Dial Key, a Combination Dial Key, a TEL/DIR, or manually entered telephone numbers. Press YES between location.

NO.001=_ OK=YES (DEL=NO)

5 When all the numbers have been entered, press START to begin your Broadcast session

NO.002=_ (Fin.=START)

3. 2 Advanced Facsimile
Page 43 of the Lanier 2002 user manual — TIMER=_0:00 OK=YES
Page 43 · click to enlarge
Page 43

Timer TX (Delay Transmission)

Timer TX (Delay Transmission)

This feature allows you to set a specified start time within 24 hours to send documents at a later time. Set the reservation timer using military time (24 hour format). This functions can also be combined with Broadcast, Mailbox TX, Polling RX, or Relay Initiate.

Procedure

1 Select the Original Type and Resolution if necessary and place your document in the Document Feeder face down.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Press the FUNCTION Key and press 2 to select the Timer TX menu.

FUNCTION SEL. 1-7 OR FUNCTION

3 The following message appears briefly to confirm your selection.

2 TIMER TX

4 Enter the time you wish the Transmission to begin.

TIMER=_0:00 OK=YES

5 Enter the destination fax number. If you press FUNCTION, the available types of Delayed Transmissions are: manually entered fax number, Broadcast, Mailbox Polling RX or Relay Initiate.

ENTER FAX NO. or FUNCTION

Advanced Facsimile 3 - 3

Page 44 of the Lanier 2002 user manual — MAILBOX PW=_ OK=YES (DEL=NO)
Page 44 · click to enlarge
Page 44

Mailbox TX

Mailbox TX

This operation is normally used to send confidential messages. Mailbox TX allows the sender the ability to send a fax message to a remote machine to be stored in memory. Only the user with the correct password can print the document. This function works only with a compatible fax machine that is set up for Mailbox reception. You need to enter the correct Mailbox PW for successful transmission.

Procedure

1 Select the Original Type, Resolution if necessary and place your document in the Document Feeder face down.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Press the FUNCTION Key and press 3 to select the Mailbox TX menu.

FUNCTION SEL. 1-7 OR FUNCTION

3 The following message appears briefly to confirm your selection.

3 MAILBOX TX? OK=YES

4 Enter the Mailbox PW (0-9) and press YES.

MAILBOX PW=_ OK=YES (DEL=NO)

5 Enter the destination fax number and press START to begin transmitting.

ENTER FAX NO.

3. 4 Advanced Facsimile
Page 45 of the Lanier 2002 user manual — *PRINT COMPLETE*
Page 45 · click to enlarge
Page 45

Print Mailbox RX

Print Mailbox RX

This operation is normally used to receive confidential messages. Mailbox TX allows the sender the ability to send a fax message to your machine to be stored in memory. Only the user with the correct password can print the document. This function works only with a compatible fax machine and your machine must be set up for Mailbox reception. You need to enter the correct Mailbox Password to access the documents in your Mailbox.

Your fax unit can be programmed with up to 10 virtual mailboxes. Each Mailbox is assigned a 4-digit Password. This Password is required to access the documents setting in your Mailbox.

Procedure

1 Select the Original Type, Resolution if necessary and place your document in the Document Feeder face down.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Press the FUNCTION Key and press 4 to select the Print Mailbox RX menu.

FUNCTION SEL. 1-7 OR FUNCTION

3 The following message appears briefly to confirm your selection.

4 PRINT MAILBOX RX? OK=YES

4 Enter the Mailbox PW to your Mailbox and press YES.

MAILBOX PW=_ OK=YES (DEL=NO)

5 If you enter the wrong PW you are prompted and then given an opportunity to enter the correct PW number.

*WRONG MAILBOX PW*

6 When the contents of your Mailbox has printed, you are prompted that printing is complete.

*PRINT COMPLETE*

Advanced Facsimile 3 - 5

Page 46 of the Lanier 2002 user manual — NOV.06 15:38 100% -SET DOC. FACE DOWN-
Page 46 · click to enlarge
Page 46

Polling TX

Polling TX

Polling TX allows you to set a document to be retrieved by a remote fax machine. Your fax machine will automatically send the stored document in response to polling requests from remote devices. You need to set a 4-digit security code to prevent unauthorized polling. Polling TX offers Single and Multi Modes.

  • In Single Mode, the specified file will be deleted after it has been successfully transmitted.
  • In Multi Mode, the specified file has to be manually deleted during a polling TX or by Cancel Reservation Session.

Procedure

1 Select the Original Type, Resolution if necessary and place your document in the Document Feeder face down.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Press the FUNCTION Key and press 5 to select the Polling TX menu.

FUNCTION SEL. 1-7 OR FUNCTION

3 The following message appears briefly to confirm your selection.

5 POLLING TX? OK=YES

4 Enter the 4-digit Polling PW and press YES.

POLLING PW=_ OK=YES (DEL=NO)

5 If you enter the wrong PW you are prompted and then given an opportunity to enter the correct PW number.

*WRONG POLLING PW*

6 Select either Single or Multi and press YES to start the Polling session.

*SINGLE MULTI -SELECT&PUSH”YES”-

7 Your document is scanned into memory, ready for it to be polled. The “P” in the Message Display indicated the Polling Document is in memory.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

3. 6 Advanced Facsimile
Page 47 of the Lanier 2002 user manual — Continuous Polling RX
Page 47 · click to enlarge
Page 47

Polling RX

Polling RX

Polling RX allows you to obtain stored documents in another fax by calling the remote fax and instructing it to transmit. To receive (poll) the document, you need to enter the correct polling PW number. Your unit sends the Polling PW code to the remote unit. The remote unit allows your unit to poll if your PW code matches the remote unit document PW.

Procedure

1 Press the FUNCTION Key and press 6 to select the Polling RX menu.

FUNCTION SEL. 1-7 OR FUNCTION

2 The following message appears briefly to confirm your selection.

6 POLLING RX? OK=YES

3 Enter the One-Touch key of the remote fax unit or enter the phone of the remote unit manually and press YES.

NO.001=_ OK=YES (SUB= )

4 The name associated with the One-Touch appears to confirm this is the location you intended to poll. Press YES to accept or NO to enter a new location.

NO.001=DALLAS OK=YES (DEL=NO)

5 Enter the Polling PW for the remote location. If you do not have this PW, you will have to contact the Key Operator for the remote fax unit for this information.

POLLING PW=_ OK=YES (DEL=NO)

6 You are given the opportunity to enter additional locations to poll. To finish, press START.

NO.002=_ (Fin.=START)

7 You are given the opportunity to check the destinations you have selected. To initiate the Polling session, press START.

CHECK DESTINATIONS? OK=YES (Fin.=START)

Continuous Polling RX

Your unit can be programmed to continuously poll up to ten groups. Each group can contain up to ten location. This allows a central unit to poll remote units on a continuous basis. Any time a document is placed in the remote unit for Polling TX, you machine will automatically receive it. Refer to the Program section for programming details.

Advanced Facsimile 3 - 7

Page 48 of the Lanier 2002 user manual — REPORT SD NO.=88 OK=YES (DEL=NO)
Page 48 · click to enlarge
Page 48

Relay Initiate

Relay Initiate

Relay TX allows the operator to make one long distance call to a remote unit and the remote unit will relay the message to one or more fax units in the local area. With this function, you can save valuable time and telephone charges. This function can also instruct the remote fax machine to send an activity report to one of its One-Touch or Speed Dial location.

Procedure

1 Select the Original Type, Resolution if necessary and place your document in the Document Feeder face down.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Press the FUNCTION Key and press 7 to select the Relay Initiate menu.

FUNCTION SEL. 1-7 OR FUNCTION

3 The following messages appear briefly to confirm your selection.

7 RELAY INITIATE? OK=YES

4 Enter the One-Touch key of the remote fax unit or enter the phone of the remote unit manually and press YES.

-SEL. RELAY STATION-

5 The name or telephone number associated with the One-Touch appears to confirm this is the location you intended to poll. Press YES to accept or NO to enter a new location.

OT01=DALLAS OK=YES (DEL=NO)

6 Using the 10-Key Pad, enter the two digit One- Touch number in the remote fax machine that represents the end locations you wish to transmit to.

RELAY GP NO.=_ OK=YES

7 Using the 10-Key Pad, enter the two digit Speed Dial number in the remote fax machine that represents the fax unit that should receive the TX Results Report.

REPORT SD NO.=88 OK=YES (DEL=NO)

8 Press START to begin transmitting. Your document is scanned into memory and sent to the Relay location.

3. 8 Advanced Facsimile
Page 49 of the Lanier 2002 user manual — 12345678 (TX=START)
Page 49 · click to enlarge
Page 49

Using Combination Dial

Using Combination Dial

Because the telephone number in each One-Touch and Speed Dial location is limited to 30 digits, it might be necessary to combine two or more One-Touch or Speed Dial locations to call one location.

Procedure

1 Select the Original Type, Resolution if necessary and place your document in the Document Feeder face down.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Press any of the One-Touch or Speed Dial Keys you have programmed.

ONE TOUCH 01 YES / or

3 The following messages appear briefly to confirm your selection.

ONE TOUCH 01

4 If the displayed number has a “+” as the last digit, additional numbers must be used to dial this locaiton.

5 At this point, you have the option to enter the additional numbers using the Ten-Key Pad, selecting another One-Touch Key or entering another Speed Dial number.

6 Enter your selection.

12345678 (TX=START)

7 To begin transmitting, press START.

Advanced Facsimile 3 - 9

1234+

Page 50 of the Lanier 2002 user manual — BILL (1) SEARCH=YES (SEE= )
Page 50 · click to enlarge
Page 50

Using TEL DIR

Using TEL DIR

The following procedure illustrates how to use LIST or SEARCH to find the specified location stored in your One-Touch or Speed Dial Keys. Once the correct destination is displayed, press the START Key to transmit the document.

LIST Procedure

1 Select the Original Type, Resolution if necessary and place your document in the Document Feeder face down.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Press the TEL DIR Key. Use the Arrow Keys to select the LIST option and press YES.

*LIST SEARCH -SELECT&PUSH”YES”-

3 The first alphabetical listing appears. If this is the desired location, press START to begin transmitting. If it is not the desired location, use the Up or Down Arrow Keys to locate the correct location and then press START.

*DICK OK=START

SEARCH Procedure

1 Select the Original Type, Resolution if necessary and place your document in the Document Feeder face down.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Press the TEL DIR Key. Use the Arrow Keys to select the SEARCH option and press YES.

LIST *SEARCH -SELECT&PUSH”YES”-

3 Type the name of the destination and press YES.

SEARCH->>_ OK=YES

4 You may also use the Up and Down Arrow Keys to step through the available locating.

BILL (1) SEARCH=YES (SEE= )

5 Once you have found the desired location, press START to begin transmitting.

3. 10 Advanced Facsimile
Page 51 of the Lanier 2002 user manual — 1 (MAR.01 14:00)TX NY OFFICE -OK
Page 51 · click to enlarge
Page 51

JOURNAL Key

JOURNAL Key

The Journal Key allows users to press the Up or Down Arrow Keys to check the transmission results on the LCD screen. Pressing the START Key then prints the report.

1 With your unit at a ready condition, press the Journal Key.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

PHOTO FINE STD EX-FINE LIGHT NORM

DARK

ME

RESOLUTION

PHOTO

TYPE ORG.

SCHEDULE

JOURNAL

REPORT

M

D TX.

08 40 SPEED DIAL

2 Using the Up and Down Arrows, select the TX you wish to check the status on.

1 (MAR.01 14:00)TX NY OFFICE -OK

3 Press the START Key to print the report.

Advanced Facsimile 3 - 11

< · > ·

Page 52 of the Lanier 2002 user manual — TX RESULT REPORT? OK=YES
Page 52 · click to enlarge
Page 52

REPORT Key

REPORT Key

The Report Key allows users to press the Up or Down Arrow Keys to print a desired report. Pressing the YES Key then prints the report.

1 With your unit at a ready condition, press the Report Key.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

PHOTO EX-FINE LIGHT NORM

DARK

AU MEM. TX.

TION

PHOTO

TYPE ORG.

LE

JOURNAL

REPORT

MEM. TX.

SPEED DIAL DEF ABC

2 Using the Up and Down Arrows, select the Report you wish to print. The report in the order they appear are:

TX RESULT REPORT? OK=YES

  • TX RESULTS REPORT?
  • RX RESULTS REPORT?
  • ACTIVITY REPORT?
  • MEMORY DATA LIST?
  • MEMORY IMAGE PRINT?
  • ONE-TOUCH LIST?
  • SPEED DIAL LIST?
  • KEY SETTING LIST?
  • MACHINE STATUS LIST?

3 Press the YES Key to print the report.

3. 12 Advanced Facsimile

> · < ·

Page 53 of the Lanier 2002 user manual — Manual TX Report
Page 53 · click to enlarge
Page 53

Reports

Reports

Many of the available reports can be programmed to print automatically. If you wish to have these set up, contact your Key Operator to set these up or refer to the Chapter on Programming.

Transmit Message Confirmation

If TX Message Confirmation Report is turned ON, this unit automatically prints a Confirmation Report. If it is turned OFF, you can still check transmission results by printing the Activity Report or pressing the JOURNAL Key to view the Journal on the LCD.

If the transmission is successful, the unit prints a report with the date and time, the receiver’s number, the number of pages that were sent and other useful information.

If the document was scanned into memory, the report prints a copy o f the first page of the transmission on the report for your reference.

If the transmission was not completed, the unit prints out an error report.

Manual TX Report

This function can be used to save paper and bulk in your files by printing the TX Results on the back of the original.

Lanier 2002 — Manual TX Report diagram (page 53)
Fig. 12 · Manual TX Report

1 When the document has finished sending, place it face up in the By-Pass Feed Tray.

2 Press the JOURNAL Key.

3 If you are doing this immediately after sending the document, press START.

4 If there has been other sessions since your transmission, use the Arrow Keys to scroll through the list and locate the phone number you sent to and press START.

Advanced Facsimile 3 - 13

Page 54 of the Lanier 2002 user manual — 004[1234] POLL TX CANCELED
Page 54 · click to enlarge
Page 54

SCHEDULE Key

SCHEDULE Key

Press this key to view the transaction in memory file, such as memory transmission or polling. You can press the YES key to cancel this schedule.

1 With your unit at a ready condition, press the Schedule Key.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 SIDED TX.

PHOTO FINE STD EX-FINE LIGHT N

RESOLUTION

PHOTO

TYP

SCHEDULE

JOURNAL

R

/2 SIDED TX. CODE PIN DELETE

06 38 07 39 08 40 SPEED DIAL

2 If there are no messages in memory, the following message appears.

*NONE*

3 Messages in memory, the following message appears. Press the Up and Down Arrow Keys to select the desired message.

001[14:55] B-CAST DELETE or (CONF.= )

4 Press the Right Arrow Key to Confirm the location this message is being set to.

001[14:55] B-CAST DELETE or (CONF.= )

5 Use the Up and Down Arrows to select the locations you wish to check and press YES.

001=DALLAS CHECK FINISH=YES

6 If you selected Delete in Step 4, you are given the opportunity to delete that transmission.

004[1234] POLL TX CANCELED

3. 14 Advanced Facsimile

< · >

Page 55 of the Lanier 2002 user manual — PIN CODE Key
Page 55 · click to enlarge
Page 55

PIN CODE Key

PIN CODE Key

The PIN CODE (Personal Identification Number) prevents unauthorized personnel from making calls. Some office telephone systems require you to enter not only the phone number but also a PIN number when you dial an outside line. You can dial a PIN plus fax number, but the PIN will not appear in the LCD or on any printout.

Lanier 2002 — PIN CODE Key diagram (page 55)
Fig. 13 · PIN CODE Key

1 With your unit at a ready condition, press the PIN CODE Key.

2 Enter your PIN Code, make sure it is correct and press YES.

3 Select the remote location using a One-Touch Key, a Speed Dial Key or manually entering the number from the 10-Key Pad.

Advanced Facsimile 3 - 15

Page 56 of the Lanier 2002 user manual — SCHEDULE
Page 56 · click to enlarge
Page 56

2 SIDED TX. Key

2 SIDED TX. Key

If 2 Side TX LED is lit during memory TX scanning, you can scan the image of one side of all the pages of the document, then turn the pages over (in the same direction), and your unit will automatically send a collated set to the remote location.

1 With your unit at a ready condition, place you document in the Document Feed Tray and make any other selections such as Original Type or Resolution.

NOV.06 15:38 100% -SET DOC. FACE DOWN-

2 Turn 2 Sided TX. mode on by pressing the DELETE/2 SIDED TX. Key.

2 SIDED TX.

P FINE STD EX-FINE

RESOLUTION

P

3 Enter the Fax number of the remote location using One-Touch, Speed Dial or manual input using the 10-Key Pad.

SCHEDULE

JO

/2 SIDED TX. S NO CODE PIN DELETE

4 Press START. Your unit scans the first sides into memory.

05 06 07 08

5 Turn your pages over so that it enters your machine in the same direction, but scans the second side.

3. 16 Advanced Facsimile

Page 57 of the Lanier 2002 user manual — HOOK Key
Page 57 · click to enlarge
Page 57
Lanier 2002 — HOOK Key diagram (page 57)
Fig. 14 · HOOK Key

The Hook Key allows the user to transmit manually. The Hook Key also allows you to verify that the line is properly connected by enabling you to hear signals from the speaker built into the fax machine.

1 With your unit at a ready condition, press the Hook Key.

2 Enter the number of the remote unit you wish to transmit to using a One-Touch Key, Speed Dial Key or manually entering it using the 10-Key Pad.

3 Once the remote machine has answered, press the START Key to begin the transmission.

(DALLAS) -PUSH START Key-

4 Press the Right Arrow Key to Confirm the location this message is being set to.

Lanier 2002 — HOOK Key diagram (page 57)
Fig. 15 · HOOK Key
  • While the message is being sent you can hear the tones and this message appears.
  • While the message is being sent you can hear the tones and this message appears.

Advanced Facsimile 3 - 17

Page 58 of the Lanier 2002 user manual — HOOK Key
Page 58 · click to enlarge
Page 58

HOOK Key

Notes:

3. 18 Advanced Facsimile
Page 59 of the Lanier 2002 user manual — Chapter 4
Page 59 · click to enlarge
Page 59

Chapter 4

Facsimile Programming

Page 60 of the Lanier 2002 user manual — Chapter Overview
Page 60 · click to enlarge
Page 60

Chapter Overview

This section gives step-by-step instructions on how to program data and how to enter fax phone numbers. You must enter your user data, such as your telephone number, name, and time before operating the machine. You can greatly increase the usefulness of your unit by choosing certain settings to best suit your needs and by entering remote unit fax telephone numbers and other data.

This chapter includes the following programming information:

  • Program Menu Structure and Use
  • Entering Initial User Data such as Date, Time and your Fax Number.
  • Setting the Line Type, Ring and Speaker Volume
  • Selecting the Dialing Type (Tone or Pulse)
  • Setting your default scan settings
  • Program telephone numbers into One-Touch, Speed Dial, Group Dial and Program Dial
  • Programming your Transmit settings
  • Programming your Receive settings.
  • Setting the Line 2 options
  • Reports
  • Other options

Facsimile Programming

Page 61 of the Lanier 2002 user manual — 1 DATE & TIME? OK=YES
Page 61 · click to enlarge
Page 61

Accessing The User Program Area

Accessing The User Program Area

This section gives step-by-step instructions on how to program the number to be stored in the One-Touch, Speed Dial and Group Dial Keys. In addition, it shows you how to set up special parameters for each One-Touch Key, including Batch Time and Relay Broadcast.

Menu Navigation

1 Press the PROGRAM Key.

DIAL REGISTRATION? YES / or 1-5

2 Use the Up or Down Arrows to step through the available menu options, or continue to press the PROGRAM Key to step it to the next menu item. The main menu items are:

  • DIAL REGISTRATION?
  • SCANNING & PRINTING?
  • TX OPERATION?
  • RX OPERATION?
  • MACHINE OPERATION?
  • REPORT?
  • INITIAL USER DATA?
  • SET PRINTER?
  • LINE 2 SETTING? Note: A more complete menu appears on the next page. See “Menu Structure.”

3 When on the Initial User Data option, press YES.

INITIAL USER DATA? YES / or 1-4

4 Use the Arrows to step through the available menu items until you find the one you wish to program.

1 DATE & TIME? OK=YES

  • 1 DATE & TIME?
  • 2 USER FAX NO.?
  • 3 USER NAME?
  • 4 DEPARTMENT PW?

5 Use the Left, Right, Up or Down Arrows to navigate through the menus.

Facsimile Programming 4 - 1

Page 62 of the Lanier 2002 user manual — MACHINE OPERATIONS?
Page 62 · click to enlarge
Page 62

Accessing The User Program Area

Menu Structure

Listed below are the PROGRAM Menu selections as they appear in your unit. Also shown are the available selections and the default settings. Once inside each selection, you will find additional help and guidance.

Menu Group Sub-Menu Selections Choices Available Default

DIAL REGISTRATION?

1 ONE-TOUCH KEY 2 SPEED DIAL 3 GROUP DIAL 4 PROGRAM DIAL 5 BATCH TX

One-Touch Speed Dial Group Dial Program Dial Start Time

Not Off

SCANNING & PRINTING:

1 RESOLUTION 2 SCAN CONTRAST 3 PRINT DENSITY 4 REDUCTION COPY 5 REC. PAPER SIZE

Standard/Fine/Super Fine LIGHT/NORMAL/DARK Dark to Light (6 steps) On / Off LETTER / LEGAL / A4

Standard Normal Step 4 Off Letter

TX OPERATION? 1 DEFAULT TX 2 CLOSED NETWORK 3 FAX FORWARDING 4 HEADER

On / Off MEM TX / ADF TX On / Off On / Off

Off MEMORY TX On Off

RX OPERATION? 1 MEMORY RX MODE 2 NO. of RINGS 3 TWO PAGE PRINT 4 REDUCTION RX 5 MAILBOX RX 6 CLOSED NETWORK 7 RX MODE 8 FOOTER 9 CONTINUE POLL RX

On / Off 1 to 16 On / On(Sort) / Off On / Off / Cut Password On / Off Auto / Manual On / Off ON / Off

Off 2 Off On Not Required Off Auto Off Off

MACHINE OPERATIONS?

1 PSTN/PBX 2 BUZZER VOLUME 3 LINE MONITOR 4 POWER SAVE MODE 5 REMOTE MONITOR 6 REMOTE PROGRAM 7 TONE/PULSE

PSTN / PBX Hi / Low / Off Hi / Low / Off Off / Timer (On and Off) On / Off On / Off Tone / Pulse (10 PPS/20)

PSTN Low Low Timer Off Off Tone

REPORT? 1 ACTIVITY REPORT 2 RESERV. REPORT 3 TX RESULT REPORT 4 RX RESULT REPORT 5 BROADCAST REPORT 6 TONER LOW REPORT

On / Off On / Off On / Off On / Off On / Off On / Off + Tel #

On Off

INITIAL USER DATA? 1 DATE & TIME 2 USER FAX NO. 3 USER NAME 4 DEPARTMENT PW

Date & Time User Fax No. User Name On / Off

Jan 1 1990 Not Required Not Required Off

4. 2 Facsimile Programming
Page 63 of the Lanier 2002 user manual — 3 LINE 2 TONE/PULSE
Page 63 · click to enlarge
Page 63

Accessing The User Program Area

Menu Group Sub-Menu Selections Choices Available Default

SET PRINTER? 1 AUTO CASSETTE SEL. 2 NUMBER OF COPIES 3 SYMBOL SET 4 FONT NUMBER 5 LINE NUMBER 6 *PRINT FONT* 7 PCL4 8 GDI ENHANCE

On / Off 1 to 99 IBM-US(24 types of fonts) 1 to 6 5 to 127

Off 1 IBM-US 1 64 Not Required Off Off

On / Off On / Off

LINE 2 SETTING 1 LINE 2 FAX NO. 2 TX LINE PRIORITY

Line 2 Fax No. Set Line 1 or Line 2 for TX Priority Tone / Pulse

3 LINE 2 TONE/PULSE

Facsimile Programming 4 - 3

Line 1 Priority · Tone

Page 64 of the Lanier 2002 user manual — Entering Numbers and Letters
Page 64 · click to enlarge
Page 64
Lanier 2002 — Entering Numbers and Letters diagram (page 64)
Fig. 16 · Entering Numbers and Letters

1 To enter numbers into a numeric field, use the 10-Key Pad.

2 To enter letters into an alpha field, use the One-Touch Keys.

3 To enter a Space between numbers or letters, use One-Touch Key #31.

4 To enter a Symbol, press One- Touch Key 28 and then the number of the symbol you need.

5 To enter a European Symbol, press One-Touch Key 29 and then the number of the symbol you need.

4. 4 Facsimile Programming
Page 65 of the Lanier 2002 user manual — _ OK=YES (DEL=NO)
Page 65 · click to enlarge
Page 65

Initial User Data

Initial User Data

Entering The Date & Time

When you set the date and time, they appear on the LCD when the unit is in standby mode. They also print at the top of each page you transmit to another location. The date and time must be set in order to use the Delay Transmit, Broadcast, and Polling functions of your unit. Follow these instructions for entering the current date and time.

1 Use the Memu Navigation procedure on page 4-1 to access the DATE & TIME? menu selection.

1 DATE & TIME? OK=YES

2 Press YES. Enter the Time and Date using the 10- Keypad.

12:39 ‘90 01 15 SET TIME (OK=YES)

3 After entering this information, check to make sure it is correct. If correct, press YES to enter it in memory. If it is incorrect, press NO and re-enter the information.

Entering Your Telephone Number

To have your phone number display on the faxes you transmit:

1 Use the Memu Navigation procedure on page 4-1 to access the USER FAX NO.? menu selection.

2 USER FAX NO.? OK=YES

2 Press YES. Enter your number.

_ OK=YES (DEL=NO)

3 After entering your number, check to make sure it is correct. If correct, press YES to enter it in memory. If the number is incorrect, press NO and re-enter the correct number

Facsimile Programming 4 - 5

Page 66 of the Lanier 2002 user manual — Setting Department PW
Page 66 · click to enlarge
Page 66

Initial User Data

Entering Your User Name

To have your user name display on the faxes you transmit:

1 Use the Memu Navigation procedure on page 4-1 to access the USER NAME? menu selection.

3 USER NAME? OK=YES

2 Press YES. Enter your name.

NAME=_ OK=YES (DEL=NO)

3 After entering your name, check to make sure it is correct. If correct, press YES to enter it in memory. If the name is incorrect, press NO and re-enter the correct name.

Setting Department PW

4. 6 Facsimile Programming
Page 67 of the Lanier 2002 user manual — *PSTN PBX -SELECT&PUSH”YES”-
Page 67 · click to enlarge
Page 67

Machine Operations

Machine Operations

This section describes the choices available in the Machine Operations Menu. Some choices may not be available to you depending on your country’s regulations.

Setting Your Fax Line Type (PSTN/PBX)

Select either PSTN or PBX depending on how your phone is connected. If your unit is connected to the public switch telephone network (PSTN), you should select “PSTN. Otherwise, you should select “PBX.”

1 Press the PROGRAM Key and scroll through the menus until you reach the Machine Operations menu and press YES.

MACHINE OPERATION? YES / or 1-7

2 Press YES since this is the first menu to appear.

1 PSTN/PBX? OK=YES

3 Use the Left/Right Arrow Keys to select either PSTN or PBX and press YES.

*PSTN PBX -SELECT&PUSH”YES”-

Note: With a PBX system. you generally have to dial a prefix number (e.g. “9”) to access an outside line. If you set the line type to “PBX”, you can set the prefix number in advance. Then the unit can dial the prefix number for you whenever you dial. The following table shows you how to dial when using the PBX mode. The prefix can be up to 4 digits in length. When you are in the PBX mode, pressing # causes the the machine to dial the programmed access number(s). If you are dialing from within a PBX and dial the extension number within the PBX the “@” symbol is displayed.

Phone Line Telephone Number LCD Display/Dialing Access Line

PBX mode, prefix=9 123 @123 PBX

PBX mode, prefix=9 #123 9-123 PBX->PSTN

Facsimile Programming 4 - 7

Page 68 of the Lanier 2002 user manual — HIGH *LOW OFF -SELECT&PUSH”YES”-
Page 68 · click to enlarge
Page 68

Machine Operations

Setting the Buzzer (Ring) Volume

Use this to set the ring volume to the suited level.

1 Press the PROGRAM Key and scroll through the menus until you reach the Machine Operations menu and press YES.

MACHINE OPERATION? YES / or 1-7

2 Press 2 or press the down arrow twice to reach the Buzzer Volume Menu. Press YES.

2 BUZZER VOLUME? OK=YES

3 Use the Left/Right Arrow Keys to select either HIGH, LOW or OFF and press YES.

HIGH *LOW OFF -SELECT&PUSH”YES”-

HIGH Buzzer Volume is set at the loudest setting available.

LOW Buzzer Volume is set at the lowest setting available.

OFF No sound will be heard.

Setting the Line Monitor (Speaker) Volume

Use this to set the speaker volume while monitoring the fax activity.

1 Press the PROGRAM Key and scroll through the menus until you reach the Machine Operations menu and press YES.

MACHINE OPERATION? YES / or 1-7

2 Press 3 or press the down arrow three times to reach the Line Monitor Menu. Press YES.

3 LINE MONITOR? OK=YES

3 Use the Left/Right Arrow Keys to select either HIGH, LOW or OFF and press YES.

HIGH *LOW OFF -SELECT&PUSH”YES”-

HIGH Speaker Volume is set at the loudest setting available.

LOW Speaker Volume is set at the lowest setting available.

OFF No sound will be heard.

4. 8 Facsimile Programming

Choices Available Description · Choices Available Description

Page 69 of the Lanier 2002 user manual — 5 REMOTE MONITOR? OK=YES
Page 69 · click to enlarge
Page 69

Machine Operations

Setting the Power Save Mode

This program allows the user to set their fax unit to automatically enter the power saving mode at a specified time. You can also set the Power Save Mode to OFF. If the ON time and the OFF time are set the same, the Power Save Mode will remain ON continuously.

1 Press the PROGRAM Key and scroll through the menus until you reach the Machine Operations menu and press YES.

MACHINE OPERATION? YES / or 1-7

2 Press 4 or press the down arrow four times to reach the Power Saver Mode Menu. Press YES.

4 POWER SAVE MODE? OK=YES

3 Use the Left/Right Arrow Keys to select either OFF or TIMER and press YES.

OFF *TIMER -SELECT&PUSH”YES”-

4 Enter the time you wish the unit to enter Power Saver Mode and press YES.

ON TIME=_0:00 OK=YES

5 Enter the time you wish the unit to leave Power Saver Mode and return to normal operation.

OFF TIME=_0:00 OK=YES

Selecting Remote Monitor

This function allows service personnel to access the unit remotely. It is possible for the Service Representative to monitor and change machine settings. This allows them to fix your unit over the telephone.

1 Press the PROGRAM Key and scroll through the menus until you reach the Machine Operations menu and press YES.

MACHINE OPERATION? YES / or 1-7

2 Press 5 or press the down arrow five times to reach the Remote Monitor Menu. Press YES.

5 REMOTE MONITOR? OK=YES

Facsimile Programming 4 - 9

Page 70 of the Lanier 2002 user manual — 7 TONE/PULSE OK=YES
Page 70 · click to enlarge
Page 70

Machine Operations

3 Use the Left/Right Arrow Keys to select either ON or OFF and press YES.

ON *OFF -SELECT&PUSH”YES”-

Selecting Remote Program

This function allows service personnel to change the unit’s firmware remotely. It is possible for the Service Representative to change the unit’s firmware if this setting is ON.

1 Press the PROGRAM Key and scroll through the menus until you reach the Machine Operations menu and press YES.

MACHINE OPERATION? YES / or 1-7

2 Press 6 or press the down arrow six times to reach the Remote Program Menu. Press YES.

6 REMOTE PROGRAM? OK=YES

3 Use the Left/Right Arrow Keys to select either ON or OFF and press YES.

ON *OFF -SELECT&PUSH”YES”-

Setting the Correct Dialing Type (Tone/Pulse)

Select either TONE or PULSE according to the type of telephone system connection to the facsimile unit.

1 Press the PROGRAM Key and scroll through the menus until you reach the Machine Operations menu and press YES.

MACHINE OPERATION? YES / or 1-7

2 Scroll through the menu options until the TONE/ PULSE options appear and press YES.

7 TONE/PULSE OK=YES

4. 10 Facsimile Programming
Page 71 of the Lanier 2002 user manual — Machine Operations
Page 71 · click to enlarge
Page 71

Machine Operations

3 Use the Left/Right Arrow Keys to select either TONE or PULSE and press YES. *TONE PULSE -SELECT&PUSH”YES”-

Facsimile Programming 4 - 11

Page 72 of the Lanier 2002 user manual — *STD FINE EX-FINE -SELECT&PUSH”YES”
Page 72 · click to enlarge
Page 72

Document Scan Settings

Document Scan Settings

To optimize scanning resolution and contrast, set according to your individual needs.

Resolution

To assure the best quality document, please set the scanning resolution and contrast according to the requirements of your original documents. The default resolution setting is Standard and the resolution will return to the default setting after each transmission if using a different resolution. Four scanning resolution options are available:

STD (Standard) (Default) Normal resolution for standard size characters.

FINE Higher resolution for the small size characters.

EXTRA FINE Highest resolution for image data.

1 Press the PROGRAM Key and scroll through the menus until you reach the SCANNING & PRINTING Menu. Press YES to begin programming.

SCANNING&PRINTING? YES / or 1-5

2 Press 1 or scroll down to the Resolution menu and press YES.

1 RESOLUTION? OK=YES

3 Using the Left and Right arrows, select the resolution you wish to have as the default and press YES to enter this selection into memory.

*STD FINE EX-FINE -SELECT&PUSH”YES”

4. 12 Facsimile Programming

Choices Available Description

Page 73 of the Lanier 2002 user manual — *STD FINE EX-FINE -SELECT&PUSH”YES”
Page 73 · click to enlarge
Page 73

Document Scan Settings

Scan Contrast

There are three contrast levels of Light, Normal, Dark that you can select depending on your original document. For documents with very fine or light characters, choose a lighter level.

1 Press the PROGRAM Key and scroll through the menus until you reach the SCANNING & PRINTING Menu. Press YES to begin programming.

SCANNING&PRINTING? YES / or 1-5

2 Press 2 or scroll down to the Scan Contrast menu and press YES.

2 SCAN CONTRAST? OK=YES

3 Using the Left and Right arrows, select the contrast you wish to have as the default and press YES to enter this selection into memory.

LIGHT *NORMAL DARK -SELECT&PUSH”YES”

Print Density

Set the print density according to your needs. There are six printing density levels ranging from Light to Dark.

1 Press the PROGRAM Key and scroll through the menus until you reach the SCANNING & PRINTING Menu. Press YES to begin programming.

SCANNING&PRINTING? YES / or 1-5

2 Press 3 or scroll down to the Print Density menu and press YES.

3 PRINT DENSITY? OK=YES

3 Using the Left and Right arrows, select the density you wish to have as the default and press YES to enter this selection into memory.

*STD FINE EX-FINE -SELECT&PUSH”YES”

Facsimile Programming 4 - 13

Page 74 of the Lanier 2002 user manual — *ON OFF -SELECT&PUSH”YES”-
Page 74 · click to enlarge
Page 74

Document Scan Settings

Reduction Copy

This function allows you to have the document printed by one of the two modes described below:

ON The facsimile machine will reduce the copy document as needed to fit on the paper. The maximum reduction proportion is 70%. If greater reduction is needed, then the remainder of the document will be printed on the next page.

OFF The facsimile machine will not reduce the copy document and will instead print the remainder of the document on the next page.

1 Press the PROGRAM Key and scroll through the menus until you reach the SCANNING & PRINTING Menu. Press YES to begin programming.

SCANNING&PRINTING? YES / or 1-5

2 Press 4 or scroll down to the Reduction Copy menu and press YES.

4 REDUCTION COPY? OK=YES

3 Using the Left and Right arrows, select the option you wish to have as the default and press YES to enter this selection into memory.

*ON OFF -SELECT&PUSH”YES”-

4. 14 Facsimile Programming

Choices Available Description

Page 75 of the Lanier 2002 user manual — *NOT AVAILABLE*
Page 75 · click to enlarge
Page 75

Document Scan Settings

Rec. Paper Size

This function allows you to choose the recording paper size in Tray 1 (standard Paper Tray) and the optional Tray 2 (PFU Paper Cassette) for the first printing after power ON. After first printing the machine remembers the paper size in the Standard Tray and Optional Paper Cassette.

1 Press the PROGRAM Key and scroll through the menus until you reach the SCANNING & PRINTING Menu. Press YES to begin programming.

SCANNING&PRINTING? YES / or 1-5

2 Press 5 or scroll down to the Rec. (Recording) Paper Size menu and press YES.

5 REC. PAPER SIZE? OK=YES

3 Using the Left and Right arrows, select the size you wish to have as the default and press YES to enter this selection into memory.

A4 *LETTER LEGAL -SELECT&PUSH”YES”-

Auto Cassette Sel.

Allows users to select the 2nd paper cassette to print out the document when the facsimile is equipped with the 2nd paper cassette. Users can set the received FAX or printed PC document to be printed out from either the Upper or Lower Tray.

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

SET PRINTER? YES / or 1-8

2 Press 1 or YES to enter the Auto Cassette Sel. menu.

3 Press YES to select Auto Cassette Selection.

1 AUTO CASS. SEL.? OK=YES

*NOT AVAILABLE*

Facsimile Programming 4 - 15

Page 76 of the Lanier 2002 user manual — EDIT *DELETE -SELECT&PUSH”YES”-
Page 76 · click to enlarge
Page 76

Dial Registration

Dial Registration

This section gives instructions on how to program the number to be stored in the One- Touch, Speed Dial and Group Dial Keys. In addition, it shows you how to set up special parameters for each One-Touch Key, including batch Time and Relay Broadcast.

One-Touch Keys

You can program the most frequently dialed fax numbers into One-Touch Keys. This allows you to transmit documents simply by pressing a One-Touch Key and the START Key. You can program any of the One-Touch Keys as Group Dial Keys with up to 50 locations in each.

1 Press the PROGRAM Key and scroll through the menus until you reach the DIAL REGISTRATION Menu. Press YES to begin programming.

DIAL REGISTRATION? YES / or 1-5

2 Press YES since this is the first menu to appear and press YES to enter the One-Touch Program.

1 ONE-TOUCH DIAL? OK=YES

3 Press the One-Touch Key you wish to program.

-SELECT REGIST. KEY-

4 Press YES to accept your selection.

ONE-TOUCH 01 or PRESS “YES”

5 Enter the Telephone number you wish to transmit to and press YES.

OK=YES

6 Enter the Name you wish associated with this number and press YES after checking to see it OK.

NAME=_ OK=YES

Edit/Deleting

1 If you wish to change any entry, a screen allows you to accept or change.

2 If you wish to change a Key that was previously programmed, this message appears. Press YES to keep this location as is, or NO if you wish to edit it.

REGISTERED! KEEP? OK=YES (EDIT/DEL=NO)

3 If you choose NO, use the arrow keys to select either EDIT or DELETE and then proceed with the needed changes.

EDIT *DELETE -SELECT&PUSH”YES”-

4. 16 Facsimile Programming
Page 77 of the Lanier 2002 user manual — EDIT *DELETE -SELECT&PUSH”YES”-
Page 77 · click to enlarge
Page 77

Dial Registration

Speed Dial Keys

The fax number and other data for a particular destination can be programmed using a 3- digit Speed Dial Number. This feature allows you to transmit a document to the particular destination by pressing the Speed Dial Key, entering the 3-digit number and pressing the START Key. You can program a fax number in any of the 200 Speed Dial locations, number 001 to 200.

Entering

1 Press the PROGRAM Key and scroll through the menus until you reach the DIAL REGISTRATION Menu. Press YES to begin programming.

DIAL REGISTRATION? YES / or 1-5

2 Press 2 or scroll down to the Speed Dial menu and press YES.

2 SPEED DIAL? OK=YES

3 Enter the number of the location you want to program and press YES.

SPEED DIAL =_ OK=YES

4 Enter the Telephone number you wish to transmit to and press YES after checking to see its OK.

OK=YES

5 Enter the Name you wish associated with this number and press YES after checking to see it OK.

NAME=_ OK=YES

6 You are given the opportunity to program additional locations. Continue to enter additional Speed Dial locations or press NO to exit.

Edit/Deleting

1 If you wish to change any entry, a screen allows you to accept or change.

2 If you wish to change a Key that was previously programmed, this message appears. Press YES to keep this location as is, or NO if you wish to edit it.

REGISTERED! KEEP? OK=YES (EDIT/DEL=NO)

3 If you choose NO, use the arrow keys to select either EDIT or DELETE and then proceed with the needed changes.

EDIT *DELETE -SELECT&PUSH”YES”-

Facsimile Programming 4 - 17

Page 78 of the Lanier 2002 user manual — EDIT *DELETE -SELECT&PUSH”YES”-
Page 78 · click to enlarge
Page 78

Dial Registration

Group Dial Keys

Instead of their regular functions, any of the One-Touch Keys can be used as Group Dial Keys. Destinations already stored for One-Touch, Speed Dial and Phone Book can be entered in a Group Dial Key. Each Group can contain up to 50 locations.

Entering

1 Press the PROGRAM Key and scroll through the menus until you reach the DIAL REGISTRATION Menu. Press YES to begin programming.

DIAL REGISTRATION? YES / or 1-5

2 Press 3 or scroll down to the Group Dial menu and press YES.

3 GROUP DIAL? OK=YES

3 Press the One-Touch Key you wish to use.

-SELECT REGIST.KEY-

4 Press YES to accept your selection.

GROUP DIAL 25 or PRESS “YES”

5 Enter the Group Name and press YES to accept.

GROUP NAME=_ OK=YES

6 Enter the Key(s) you wish included in this group. Remember, you can include any One-Touch, Speed Dial, or Phone Book entry already in memory.

NO.001=_

7 Continue to enter the locations you wish to include and then press YES. You are given the opportunity to program additional locations. Continue to enter additional Speed Dial locations or press NO to exit.

Edit/Deleting

1 If you wish to change any entry, a screen allows you to accept or change.

2 If you wish to change a Key that was previously programmed, this message appears. Press YES to keep this location as is, or NO if you wish to edit it.

REGISTERED! KEEP? OK=YES (EDIT/DEL=NO)

3 If you choose NO, use the arrow keys to select either EDIT or DELETE and then proceed with the needed changes.

EDIT *DELETE -SELECT&PUSH”YES”-

4. 18 Facsimile Programming
Page 79 of the Lanier 2002 user manual — NO.001=_
Page 79 · click to enlarge
Page 79

Dial Registration

Program Dial

Instead of their regular functions, any of the last eight One-Touch Keys (57-64) can be used as Program Keys. Transmission functions including: Broadcast, Timer TX (Delayed Transmission), Mailbox, Polling RX, and Relay Initiation can be programmed into the programmed One-Touch Keys. This allows you to “One-Touch” an operation that normally takes multiple key strokes.

Settings entered into these program keys remain in memory for future use.

Entering

1 Press the PROGRAM Key and scroll through the menus until you reach the DIAL REGISTRATION Menu. Press YES to begin programming.

DIAL REGISTRATION? YES / or 1-5

2 Press 4 or scroll down to the Program Dial menu and press YES.

4 PROGRAM DIAL? OK=YES

3 Press the One-Touch Key you wish to use. Remember, it must be one of the last eight.

-SELECT REGIST.KEY-

4 Choose the function you wish to program: 1=Broadcast, 2=Timer TX, 3=Mailbox TX, 6=Polling RX, and 7=Relay Initiate.

FUNCTION SEL. 1/2/3/6/7

For 1=Broadcast:

5 A screen appears to confirm Broadcast was your selection.

BROADCAST

6 Enter the Key(s) you wish included in this group. Remember, you can include any One-Touch, Speed Dial, or Phone Book entry already in memory.

NO.001=_

7 Continue to enter the locations you wish to include and then save. You are given the opportunity to program additional locations. Continue to enter additional Speed Dial locations or press NO to exit.

Facsimile Programming 4 - 19

Page 80 of the Lanier 2002 user manual — NO.001=_
Page 80 · click to enlarge
Page 80

Dial Registration

For 2=Timer TX:

5 A screen appears to confirm Timer TX was your selection.

TIMER TX

6 Enter the time you wish the transmission to occur and press YES.

TIMER=_0:00 OK=YES

7 Enter the fax number you wish to send to or select a One-Touch ro Speed Dial location and press YES.

ENTER FAX NO. or FUNCTION

Once this function has been programmed, you use it by simply pressing the One-Touch Key you have just programmed. This is documented in Chapter 3 Advanced Facsimile.

For 3 = Mailbox TX:

5 A screen appears to confirm Mailbox TX was your selection.

MAILBOX TX

6 Enter the number of the Mailbox you wish use and press YES.

MAILBOX PW=_ OK=YES

7 Enter the fax number you wish to send to or select Function. If you elect to enter a phone number,

ENTER FAX NO.

Once this function has been programmed, you use it by simply pressing the One-Touch Key you have just programmed. This is documented in Chapter 3 Advanced Facsimile.

For 6 = Polling RX:

5 A screen appears to confirm Polling RX was your selection.

MAILBOX TX

6 Enter the number of the Mailbox you wish use and press YES.

NO.001=_

4. 20 Facsimile Programming
Page 81 of the Lanier 2002 user manual — EDIT *DELETE -SELECT&PUSH”YES”-
Page 81 · click to enlarge
Page 81

Dial Registration

7 Enter the Polling PW.

POLLING PW-_000 OK=YES (DEL=NO)

Once this function has been programmed, you use it by simply pressing the One-Touch Key you have just programmed. This is documented in Chapter 3 Advanced Facsimile.

For 7 = Relay Initiate:

5 A screen appears to confirm Relay Initiate was your selection.

RELAY INITIATE

6 Select the One-Touch Key under which the remote unit you wish to use as a Relay Station was entered.

-SEL. RELAY STATION-

7 Press YES to accept your entry or use the arrows to select another.

ONE TOUCH 01 YES / or

Once this function has been programmed, you use it by simply pressing the One-Touch Key you have just programmed. This is documented in Chapter 3 Advanced Facsimile.

Edit/Deleting

1 If you wish to change any entry, a screen allows you to accept or change.

2 If you wish to change a Key that was previously programmed, this message appears. Press YES to keep this location as is, or NO if you wish to edit it.

REGISTERED! KEEP? OK=YES (EDIT/DEL=NO)

3 If you choose NO, use the arrow keys to select either EDIT or DELETE and then proceed with the needed changes.

EDIT *DELETE -SELECT&PUSH”YES”-

Batch TX

You can program your single location One-Touch Key to automatically batch documents. By assigning a batch time to a programmed One-Touch Key, you can eliminate repeated calls to the same number throughout the day. Your unit calls the remote unit at a preset time and transmits all documents stored in memory for this particular destination in one phone call.

Facsimile Programming 4 - 21

Page 82 of the Lanier 2002 user manual — EDIT *DELETE -SELECT&PUSH”YES”-
Page 82 · click to enlarge
Page 82

Dial Registration

Entering

1 Press the PROGRAM Key and scroll through the menus until you reach the DIAL REGISTRATION Menu. Press YES to begin programming.

DIAL REGISTRATION? YES / or 1-5

2 Press 5 or scroll down to the Batch TX menu and press YES.

5 BATCH TX?

3 Press the One-Touch Key you wish to use.

-SELECT REGIST.KEYOK=YES

ONE-TOUCH 25

4 Enter the time at which the batch should be transmitted and press YES to accept.

TX TIME=_0:00 OK=YES

  • This screen confirms your entry.

*SET ONE-TOUCH 25 23:00

5 Press the START key to enter this information into memory, or press NO to exit.

-SELECT REGIST. KEY- (COMPLETE=NO)

Edit/Deleting

1 If you wish to change any entry, a screen allows you to accept or change.

2 If you wish to change a Key that was previously programmed, this message appears. Press YES to keep this location as is, or NO if you wish to edit it.

REGISTERED! KEEP? OK=YES (EDIT/DEL=NO)

3 If you choose NO, use the arrow keys to select either EDIT or DELETE and then proceed with the needed changes.

EDIT *DELETE -SELECT&PUSH”YES”-

4. 22 Facsimile Programming
Page 83 of the Lanier 2002 user manual — *MEM TX ADF TX -SELECT&PUSH”YES”-
Page 83 · click to enlarge
Page 83

TX Operation

TX Operation

Default TX

This function is used to set the default TX mode of the fax unit. Two options are available:

Memory TX When set in this mode, documents are scanned into memory for transmission and dialing starts after the first pages is scanned (Quick TX).

ADF TX (Direct Transmission)

When set in this mode, documents are scanned for transmission after connection has been made to the receiving unit. (When the available memory is insufficient, please select ADF TX for a successful transmission) If line is not available, the message “LINE IS BUSY” will be displayed. The facsimile will retry based on the number of redial attempts and intervals that were preset.

1 Press the PROGRAM Key and scroll through the menus until you reach the TX Operation Menu. Press YES to begin programming.

TX OPERATION? YES / or 1-2

2 Press 1 or scroll down to the Default TX menu and press YES.

1 DEFAULT TX? OK=YES

3 Using the Left and Right arrows, select the option you wish to have as the default and press YES to enter this selection into memory.

*MEM TX ADF TX -SELECT&PUSH”YES”-

Facsimile Programming 4 - 23

Choices Available Description

Page 84 of the Lanier 2002 user manual — FORWARD TX =ON OK=YES
Page 84 · click to enlarge
Page 84

TX Operation

Closed Network TX

When closed network TX/RX mode is set ON, transmission is possible only with the destination stations registered in One-Touch and Speed Dial.

1 Press the PROGRAM Key and scroll through the menus until you reach the TX Operation Menu. Press YES to begin programming.

TX OPERATION? YES / or 1-2

2 Press 1 or scroll down to the Closed Network menu and press YES.

2 CLOSED NETWORK? OK=YES

3 Using the Left and Right arrows, select the option you wish to have as the default and press YES to enter this selection into memory.

ON *OFF -SELECT&PUSH”YES”-

Fax Forwarding

This allows a user to set 20 different remote telephone numbers for fax forwarding. If you specify a telephone number, only those messages from that number will be forwarded. If you don’t specify a remote telephone number, all the incoming message will be forward to specified location.

1 Press the PROGRAM Key and scroll through the menus until you reach the TX Operation Menu. Press YES to begin programming.

TX OPERATION? YES / or 1-2

2 Press 3 or scroll down to the Fax Forwarding menu and press YES.

3 FAX FORWARDING? OK=YES

3 Select a location number 01 through 20 to which you wish forward your messages. Press YES to enter this selection into memory.

FORWARD NO.=_1 OK=YES / or 01-20

4 Select either ON or OFF and press YES.

FORWARD TX =ON OK=YES

5 Select the day you wish the forwarding to begin and press YES.

SEL. START DAY=SUN. OK=YES / or 0-6

4. 24 Facsimile Programming
Page 85 of the Lanier 2002 user manual — 9998884444 OK=YES (DEL=NO)
Page 85 · click to enlarge
Page 85

TX Operation

6 Select the day you wish the forwarding to stop and press YES.

SEL. STOP DAY=WEN. OK=YES / or 0-6

7 Select the time you wish the forwarding to begin and press YES.

SEL. START TIME=_0:00 OK=YES (DEL=NO)

8 Select the time you wish the forwarding to stop and press YES.

SEL. STOP TIME=_0:00 OK=YES (DEL=NO)

9 Determine if you also want the message to print locally. Select either ON or OFF and press YES.

PRINT AT LOCAL=OFF OK=YES

10 Determine if you want some or all of your messages forwarded. Select SPECIFIC or ALL and press YES.

*SPECIFIC ALL -SELECT&PUSH”YES”-

11 Enter the telephone number for the remote unit from which you will be receiving the message.

ENTER REMOTE FAX NO.

7778885555 OK=YES (DEL=NO)

12 Enter the remote fax number to which you wish to have the messages sent and press YES.

ENTER FORWARD TEL NO.

13 Select the day you wish the forwarding to begin and press YES.

9998884444 OK=YES (DEL=NO)

14 Select the day you wish the forwarding to begin and press YES.

FORWARD NO.=_1 OK=YES ? or 01-20

Facsimile Programming 4 - 25

Page 86 of the Lanier 2002 user manual — *ON OFF OK=YES
Page 86 · click to enlarge
Page 86

TX Operation

Header

The header prints the sender machine name, fax number, date/time and page number at the top of the sheet at the remote location. This is required by the FCC in the USA and is regulated in other way in other countries. In the USA you will have one of the following options.

  • Inside the Body: This places the header in the first 5mm of the copy top. It does not shift the copy down. Some copy may be overwritten.
  • Outside the Body: This places the header in the first 5mm of the copy top. It then start the body below this. Depending on the remote machine settings one of three things happen: 1) because the copy is not a full page, the copy fits below the header at 100%, 2) the copy is reduced to fit the page, or 3) the copy is split into two pages at 100%.

1 Press the PROGRAM Key and scroll through the menus until you reach the TX Operation Menu. Press YES to begin programming.

TX OPERATION? YES / or 1-4

2 Press 4 or scroll down to the Header menu and press YES.

4 HEADER? OK=YES

3 Select if you wish to turn the header ON or OFF and press YES.

*ON OFF OK=YES

4. 26 Facsimile Programming
Page 87 of the Lanier 2002 user manual — ON *OFF -SELECT&PUSH”YES”-
Page 87 · click to enlarge
Page 87

RX Operation

RX Operation

Memory RX Mode

ON = Memory Lock

In Memory RX Mode, the machine stores all received documents in memory. The document is not printed until the machine receives a print command. The print command can be activated by a timer or password. The print timer command instructs the machine to start printing the document stored in memory at the specified time. The password print command, instructs the machine to start printing when a password is entered. A password print command can also be used to override the print timer command. If the print timer command has been set and you want to print your incoming messages before the set time, you can enter your password to print the document immediately.

OFF

If the unit is set in the Memory RX Mode OFF status, then the received document will be printed out directly instead of being stored in memory.

Case 1: If there is no data stored in the memory and the unit is set in OFF status, then the received documents print out directly. Case 2: If there is a document stored in the memory and the unit is set in OFF status, then the previously received documents printed out first.

1 Press the PROGRAM Key and scroll through the menus until you reach the RX Operation Menu. Press YES to begin programming.

RX OPERATION? YES / or 1-9

2 Press 1 or scroll down to the Menu RX Mode menu and press YES.

1 MEM RX MODE? OK=YES

3 Using the Left and Right arrows, select the option you wish to have as the default and press YES to enter this selection into memory.

ON *OFF -SELECT&PUSH”YES”-

Facsimile Programming 4 - 27

Page 88 of the Lanier 2002 user manual — <<M-RX>> 100% -SET DOC.FACE DOWN-
Page 88 · click to enlarge
Page 88

RX Operation

4 To select Memory RX ON, use the left and right Arrow Keys to select ON and press YES.

*ON OFF -SELECT&PUSH”YES”-

5 Enter the time you wish to start receiving messages into memory.

ON TIME=_0:00 OK=YES

6 Enter the time you wish to stop receiving messages into memory.

OFF TIME=_0:00 OK=YES

7 If a password was set for this feature, you have to enter it for this to work. If you need a password, contact your Key Operator.

8 If you have your unit programmed for Memory RX with the Timer turned ON, your screen shows the following message.

*M-RX-ON* <T>

9 If you have your unit programmed for Memory RX with the Timer turned ON and a Password required, your screen shows the following message.

*M-RX-ON* <T><PWD>

10 The ready message for your unit now shows that Memory RX is active.

<<M-RX>> 100% -SET DOC.FACE DOWN-

4. 28 Facsimile Programming
Page 89 of the Lanier 2002 user manual — ON ON(SORT) *OFF -SELECT&PUSH”YES”-
Page 89 · click to enlarge
Page 89

RX Operation

No. of Rings

The unit will answer an incoming call after the number of rings (1-16) set in this menu. The default setting is 2 rings.

1 Press the PROGRAM Key and scroll through the menus until you reach the RX Operation Menu. Press YES to begin programming.

RX OPERATION? YES / or 1-9

2 Press 2 or scroll down to the No. of Rings menu and press YES.

2 NO. of RINGS? OK=YES

3 Enter the number of rings you wish to have as the default and press YES to enter this selection into memory.

NO. of RINGS=_2 OK=YES (DEL=NO)

Two Page Print

With this function, you can set the facsimile to print two copies of a document.

ON (Stack Mode) The facsimile will print copies of the document without sorting the document.

ON (Sort Mode) The facsimile will print two copies of the document and sort the document.

OFF The facsimile will print only one copy of the document.

1 Press the PROGRAM Key and scroll through the menus until you reach the RX Operation Menu. Press YES to begin programming.

RX OPERATION? YES / or 1-9

2 Press 3 or scroll down to the Two Page Print menu and press YES.

3 TWO PAGE PRINT? OK=YES

3 Using the Left and Right arrows, select the option you wish to have as the default and press YES to enter this selection into memory.

ON ON(SORT) *OFF -SELECT&PUSH”YES”-

Facsimile Programming 4 - 29

Choice Available Description

Page 90 of the Lanier 2002 user manual — *ON OFF CUT -SELECT&PUSH”YES”-
Page 90 · click to enlarge
Page 90

RX Operation

Reduction RX

This function allows you to choose among the three modes described below:

ON The facsimile machine will reduce the documents as needed to fit on the paper. The maximum reception proportion is 70%.

OFF The facsimile machine will not reduce the document and instead will print the remainder on a second page if the image size exceeds the length of the paper.

CUT The facsimile machine will automatically cut off the remainder of the document if it is less than 18 mm. If the remainder exceeds 18mm, it will be printed on a second page.

1 Press the PROGRAM Key and scroll through the menus until you reach the RX Operation Menu. Press YES to begin programming.

RX OPERATION? YES / or 1-9

2 Press 4 or scroll down to the Reduction RX menu and press YES.

4 REDUCTION RX? OK=YES

3 Using the Left and Right arrows, select the resolution you wish to have as the default and press YES to enter this selection into memory.

*ON OFF CUT -SELECT&PUSH”YES”-

Mailbox RX

This function is used to set up the personal mailbox to keep received documents confidential. Each mailbox is protected with a specified 4-digit password number.

4. 30 Facsimile Programming

Choices Available Description

Page 91 of the Lanier 2002 user manual — 7 RX MODE? OK=YES
Page 91 · click to enlarge
Page 91

RX Operation

Closed Network

Set to ON when you want to receive documents only from specified parties. When activated, it will only accept receptions from those numbers registered in the One-Touch or Speed Dial Keys.

ON Closed Network RX mode is applicable to the numbers registered in the One-Touch and Speed Dial Keys.

OFF Disable the function. You are able to receive from all parties.

1 Press the PROGRAM Key and scroll through the menus until you reach the RX Operation Menu. Press YES to begin programming.

RX OPERATION? YES / or 1-9

2 Press 4 or scroll down to the Closed Network menu and press YES.

6 CLOSED NETWORK? OK=YES

3 Using the Left and Right arrows, select the option you wish to have as the default and press YES to enter this selection into memory.

ON *OFF -SELECT&PUSH”YES”-

RX Mode

This function is used to set the mode in which the facsimile machine receives the document.

AUTO In this mode, the facsimile machine will automatically answer the phone call and receive the document.

MANUAL In this mode, the facsimile will not automatically receive the document. The user must answer each call manually.

1 Press the PROGRAM Key and scroll through the menus until you reach the RX Operation Menu. Press YES to begin programming.

RX OPERATION? YES / or 1-9

2 Press 6 or scroll down to the Closed Network menu and press YES.

7 RX MODE? OK=YES

Facsimile Programming 4 - 31

Choices Available Description · Choices Available Description

Page 92 of the Lanier 2002 user manual — ON *OFF -SELECT&PUSH”YES”-
Page 92 · click to enlarge
Page 92

RX Operation

3 Using the Left and Right arrows, select the option you wish to have as the default and press YES to enter this selection into memory.

*AUTO MANUAL -SELECT&PUSH”YES”-

Footer (Receive Time Print)

The footer is printed at the bottom of each page received showing the receiving machine’s fax number, date and the time of reception, the sender’s fax number, the reception control number and page number.

1 Press the PROGRAM Key and scroll through the menus until you reach the RX Operation Menu. Press YES to begin programming.

RX OPERATION? YES / or 1-9

2 Press 4 or scroll down to the Closed Network menu and press YES.

8 FOOTER? OK=YES

3 Using the Left and Right arrows, select the option you wish to have as the default and press YES to enter this selection into memory.

ON *OFF -SELECT&PUSH”YES”-

4. 32 Facsimile Programming
Page 93 of the Lanier 2002 user manual — RX Operation
Page 93 · click to enlarge
Page 93

RX Operation

Continuous Poll RX

Poll the specified location with pre-set timer. Up to 10 groups can be set for polling, and each group can set 10 locations.

1 Press the PROGRAM Key and scroll through the menus until you reach the RX Operation Menu. Press YES to begin programming.

Lanier 2002 — RX Operation diagram (page 93)
Fig. 17 · RX Operation

2 Press 10 or scroll down to the Continuous Polling RX menu and press YES.

3 Enter the Poll Group number you will to assign to this group and press YES.

4 The next screen indicates that this Poll Group is not active. Press YES to continue.

5 Select a start day to begin polling. Press YES to continue.

6 Select a stop day to finish polling. Press YES to continue.

7 Enter a start time to begin polling. Press YES to continue.

8 Enter a stop time to finish polling. Press YES to continue.

9 Enter the number of minutes between each redail. Press YES to continue.

10 Enter the remote fax number to be polled.

11 Press YES to continue.

Facsimile Programming 4 - 33

Page 94 of the Lanier 2002 user manual — POLLING PW=_000 OK=YES (DEL=NO)
Page 94 · click to enlarge
Page 94

RX Operation

12 Enter the 4-digit Polling Password. This number is set at the remote location and you must match it when sending to them.

POLLING PW=_000 OK=YES (DEL=NO)

13 If you wish to poll more than one location, enter that location. When you are done entering the data, press START to enter the data into memory.

NO. 002=_ (Fin.=START)

4. 34 Facsimile Programming
Page 95 of the Lanier 2002 user manual — _ OK=YES
Page 95 · click to enlarge
Page 95

Line 2 Setting

Line 2 Setting

The Optional Dual-Line kit allows you to connect one more telephone line to the fax unit at the same time. You can select either telephone line for priority reception, and you can also select which line is to be used for priority sending when both lines are open.

Line 2 Fax No.

Register your second fax number. It’s operation is the same as entering it for Line 1.

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

LINE 2 SETTING? YES / or 1-3

2 Press YES or 1 to select the first menu, Line 2 Fax No. Press Yes.

1 LINE 2 FAX NO.? OK=YES

3 Enter the telephone number of your second fax line. Press YES to accept this data into memory.

_ OK=YES

TX Line Priority

This allows the user to determine the priority of the second line.

LINE 1 TX PRIORITY When both lines are read, transmission is sent on line 1. If line 1 is busy and line 2 is read, transmission is sent on line 2.

LINE 2 TX PRIORITY When both lines are read, transmission is sent on line 2. If line 2 is busy and line 1 is read, transmission is sent on line 1.

LINE 1 TX PROHIBIT Even if both lines are read, transmission is sent on line 2. Line 1 is only available for receiving.

LINE 2 TX PROHIBIT Even if both lines are read, transmission is sent on line 1. Line 2 is only available for receiving.

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

LINE 2 SETTING? YES / or 1-3

Facsimile Programming 4 - 35

Choices Available Description

Page 96 of the Lanier 2002 user manual — *TONE PULSE - SELECT&PUSH”YES”-
Page 96 · click to enlarge
Page 96

Line 2 Setting

2 Press 2 or scroll down to the TX Line Priority menu and press YES.

2 TX LINE PRIORITY? OK=YES

3 Select either 1 or 2 as the line you wish to transmit on. Press YES to accept this data into memory.

LINE 1 TX PRIORITY? OK=YES

Line 2 Tone / Pulse

This allows the user to set the dialing mode of line 2. It’s operation is the same of TONE/ PULSE setting for Line 1.

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

LINE 2 SETTING? YES / or 1-3

2 Press 3 or scroll down to the Line 2 Tone/Pulse menu and press YES.

3 LINE2 TONE/PULSE? OK=YES

3 Select either Tone or Pulse. Press YES to accept this data into memory.

*TONE PULSE - SELECT&PUSH”YES”-

4. 36 Facsimile Programming
Page 97 of the Lanier 2002 user manual — *ON OFF -SELECT&PUSH”YES”-
Page 97 · click to enlarge
Page 97

Reports

Reports

This unit can print several different reports to aid in managing your fax traffic and the unit itself.

Activity Report

An Activity Report prints the results for the past 60 communications. it is used to check whether a communication was successful, the number of communications made, and communication time.

1 Press the PROGRAM Key and scroll through the menus until you reach the Reports menu and press YES.

REPORTS? YES / or 1-6

2 Press YES since this is the first menu to appear.

1 ACTIVITY REPORT? OK=YES

3 Use the Left/Right Arrow Keys to select either ON or OFF and press YES.

*ON OFF -SELECT&PUSH”YES”-

Reserv. (Reservation) Report

A Reservation Report prints a list of reservations for broadcast transmission. When the function is turned ON, a Reservation Report is printed before a broadcast transmission or multi-polling reception is made, allowing you to check the details of the reservation request.

1 Press the PROGRAM Key and scroll through the menus until you reach the Reports menu and press YES.

REPORTS? YES / or 1-6

2 Press 2 or scroll down to the Reserv. Report menu and press YES.

2 RESERV. REPORT? OK=YES

3 Use the Left/Right Arrow Keys to select either ON or OFF and press YES.

*ON OFF -SELECT&PUSH”YES”-

Facsimile Programming 4 - 37

Page 98 of the Lanier 2002 user manual — *ON OFF -SELECT&PUSH”YES”-
Page 98 · click to enlarge
Page 98

Reports

TX Results Report

A TX Results Report prints the results of a transmission after it has been completed. This report can be used to check whether a transmission has been successful.

1 Press the PROGRAM Key and scroll through the menus until you reach the Reports menu and press YES.

REPORTS? YES / or 1-6

2 Press 3 or scroll down to the TX Results Report menu and press YES.

3 TX RESULTS REPORTX? OK=YES

3 Use the Left/Right Arrow Keys to select either ON or OFF and press YES.

*ON OFF -SELECT&PUSH”YES”-

RX Results Report

A RX Results Report prints the results after receiving a Confidential or Multi-Polling document or when errors occur during reception. This report can be used to check whether a reception by Mailbox or Multi-Polling has been successful.

1 Press the PROGRAM Key and scroll through the menus until you reach the Reports menu and press YES.

REPORTS? YES / or 1-6

2 Press 4 or scroll down to the RX Results Report menu and press YES.

4 RX RESULTS REPORT? OK=YES

3 Use the Left/Right Arrow Keys to select either ON or OFF and press YES.

*ON OFF -SELECT&PUSH”YES”-

4. 38 Facsimile Programming
Page 99 of the Lanier 2002 user manual — ON *OFF -SELECT&PUSH”YES”-
Page 99 · click to enlarge
Page 99

Reports

Broadcast Report

A Broadcast Report prints a list of results of broadcast transmission.

1 Press the PROGRAM Key and scroll through the menus until you reach the Reports menu and press YES.

REPORTS? YES / or 1-6

2 Press 5 or scroll down to the Broadcast Report menu and press YES.

5 BROADCAST REPORT? OK=YES

3 Use the Left/Right Arrow Keys to select either ON or OFF and press YES.

*ON OFF -SELECT&PUSH”YES”-

Toner Low Report

A Toner Low Report will transmit to the service center when the toner is low.

1 Press the PROGRAM Key and scroll through the menus until you reach the Reports menu and press YES.

REPORTS? YES / or 1-6

2 Press 6 or scroll down to the Toner Low Report menu and press YES.

6 TONER LOW REPORT? OK=YES

3 Use the Left/Right Arrow Keys to select either ON or OFF and press YES.

ON *OFF -SELECT&PUSH”YES”-

4 Enter the Telephone number per your Lanier Service Representative.

Facsimile Programming 4 - 39

Page 100 of the Lanier 2002 user manual — O X
Page 100 · click to enlarge
Page 100

Reports

Other Reports and Lists

This unit can print other reports and lists that are useful in managing and optimizing your fax traffic. See the list below. Some of these are covered in other sections of this manual in more detail.

Report Name Description Printing

One-Touch List Prints a list of destinations which have been programmed for One-Touch Dial Keys. X O

Speed Dial List Prints a list of the destinations which have been programmed for the Speed Dial Keys. X O

Memory Data List Prints a list of the documents to be transmitted and those that are stored in memory.

X O

Memory Image Print Prints the first page of the document stored in memory which has yet to be transmitted. X O

Key Setting List Prints a List of the settings for Group Dial and Program Dial Keys. X O

Machine Status List Prints a list of current settings, including Page counts. X O

Memory Full Report Prints out when a memory overflow occurs. O X

Power Fail Report Prints a list of documents whose data has been lost and which were not transmitted due to a power failure occurring while the documents were stored in memory.

O X

Backup RAM Error Report

Before turning OFF, the unit prints out a list of the PROGRAM Utilities, etc., that were not stored in Backup RAM because of memory error.

O X

O = Yes X = No

Auto printing is set using the PROGRAM Utilities. - When auto printing is set to ON, the report is printed automatically. - When auto printing is set to OFF, the report can only be printed when started manually from the machine’s control panel.

4. 40 Facsimile Programming

Auto Manual

Page 101 of the Lanier 2002 user manual — DEPARTMENT 1 PW=_ OK=YES
Page 101 · click to enlarge
Page 101

Setting the Department Number and Password (PW)

1 Use the Accessing User Data procedure to access the INITIAL USER DATA menu selection.

4 DEPARTMENT PW? OK=YES

2 Press YES. Enter your number.

*SWITCH REGISTER -SELECT&PUSH”YES”-

3 Use the Left/Right Arrow Keys to select REGISTER and press YES.

SWITCH *REGISTER -SELECT&PUSH”YES”-

4 Enter the Department number (0-9).

DEPARTMENT NO=_ SELECT 0-9

5 Enter the Department Password number using the Numeric Keypad.

DEPARTMENT 1 PW=_ OK=YES

Page 102 of the Lanier 2002 user manual — PW
Page 102 · click to enlarge
Page 102

6 Use pencil to note the assignments. This will allow you to change them as needed. Remember to file this in a secure place.

Dept. ID No.

Dept.

Dept. Name* Dept. ID No.

Dept.

Dept. Name*

PW

PW

* The Department Name is not entered in machine memory. It is listed here only for your convenience.

7 Once the Department PW has been entered for a given Department ID, a message appears informing you it has been used. If you wish to edit this information, follow the instructions given in the display.

Page 103 of the Lanier 2002 user manual — PW
Page 103 · click to enlarge
Page 103

Assigning a Private Mailbox ID and Password (PW)

1 Use the Accessing User Data procedure to access the RX OPERATION? menu selection.

RX OPERATION? YES / or 1-9

2 Enter 5 or press the Up or Down Arrow until you reach the MAILBOX RX? menu.

5 MAILBOX ID? OK=YES

3 Press YES. Enter the number (0-9) for your mailbox ID.

MAILBOX NO. =_ SELECT 0-9

4 At the next screen, enter the 4-digit password for this mailbox location.

MAILBOX 9 PW=_ OK=YES

5 Use pencil to note the assignments. This will allow you to change them as needed. Remember to file this in a secure place.

ID No.

PW

ID No.

PW

*The Mailbox Name is not entered in machine memory. It is listed here only for your convenience.

Show 8 more labels / short text on this page
Mailbox · Mailbox · Mailbox · Mailbox · Mailbox · Mailbox · Name* · Name*
Page 104 of the Lanier 2002 user manual — Assigning a Private Mailbox ID and Password (PW)
Page 104 · click to enlarge
Page 104

6 Once the Department No. and PW have been entered, a message appears informing you it has been used. If you wish to edit this information, follow the instructions given in the display.

Page 105 of the Lanier 2002 user manual — PASSWORD=_ OK=YES (DEL=NO)
Page 105 · click to enlarge
Page 105

Editing the RX in Memory Password (PW)

1 Press the PROGRAM Key and scroll to the RX OPERATION? menu selection.

RX OPERATION? YES / or 1-9

2 Scroll to the MEM RX MODE menu and press YES.

1 MEM RX MODE? OK=YES

3 Determine if you want Memory Receive ON or OFF and press YES.

ON *OFF -SELECT&PUSH”YES”-

4 Assuming you want it ON, you will now need to enter the times you wish it to be active. Enter the ON tine and press YES.

ON TIME=_0:00 OK=YES

5 Then enter the OFF time and enter YES.

OFF TIME=_0:00 OK=YES

6 At the next screen, enter the 4-digit password for the Memory Receive function.

PASSWORD=_ OK=YES (DEL=NO)

7 Use pencil to note the assignments. This will allow you to change them as needed. Remember to file this in a secure place.

Memory Receive PW (Password)

8 Once the Memory Receive PW has been entered, a message appears informing you it has been used. If you wish to edit this information, follow the instructions given in the display.

Page 106 of the Lanier 2002 user manual — Editing the RX in Memory Password (PW)
Page 106 · click to enlarge
Page 106
Page 106 of the Lanier 2002 user manual — Editing the RX in Memory Password (PW)
Page 107 of the Lanier 2002 user manual — Chapter 5
Page 107 · click to enlarge
Page 107

Chapter 5

PC Printing & Scanning

Page 108 of the Lanier 2002 user manual — Chapter Overview
Page 108 · click to enlarge
Page 108

Chapter Overview

This chapter contains information for using your unit as a printer and scanner. These functions are optional on your unit. This section includes:

  • Printer Settings
  • Memory Allocations
  • PCL4 printer emulation
  • Printer Messages
  • GDI Printer Feature
  • Scanning (TWAIN Driver Option)
  • Class 1 Fax/Modem

PC Printing & Scanning

Page 109 of the Lanier 2002 user manual — GDI ENHANCE
Page 109 · click to enlarge
Page 109

Set Printer (2002 Only)

Set Printer (2002 Only)

The Set Printer Menu enables you to select settings for Auto Cassette Selection, Number of Copies, Symbol Set, Font Number, PCL4 and 600 dpi.

Menu Item Available Default Description

ON or OFF OFF Set the document to be printed out either via the Low-Tray or the High-Tray according to personal needs.

Range 1-99 1 Choose the number of copies you want to print. You can override this through the computer software.

Symbol Set 23 kinds of symbols

IBM-US Choose the appropriate symbol set for your screen and for printing.

Font Number 01-06 01 Select the default font by number. You can find the number on the font printout. The default 01 is Courier Portrait Medium. The font number also indicates whether it prints landscape or portrait.

Line Number 5-127 64 Select the number of printed lines per page.

PCL4 ON or OFF ON Select print PCL4 Interface.

GDI ENHANCE

ON or OFF OFF Select print 600 dpi Interface.

PC Printing & Scanning 5 - 1

Auto Cassette Select · Number of Copies

Page 110 of the Lanier 2002 user manual — 3 SYMBOL SET? OK=YES
Page 110 · click to enlarge
Page 110

Set Printer (2002 Only)

Number of Copies

Allows user to set the number of copies desired. The maximum number of copies is 99. You can override this function through the computer software.

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

SET PRINTER? YES / or 1-8

2 Press 2 or scroll down to the Number of Copies menu and press YES.

2 NUMBER OF COPIES? OK=YES

3 Enter the number of copies you want as your default setting. Press YES to accept this data into memory.

COPY PAGE=_1 OK=YES (DEL=NO)

Symbol Set

Allows users to choose the appropriate symbol set for printing. Choose the appropriate symbol set for printing with PCL4 emulation. If your application does not control this, you may need to select a different symbol set to match the language character, math symbols, and graphical characters.

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

SET PRINTER? YES / or 1-8

2 Press 3 or scroll down to the Symbol Set menu and press YES.

3 SYMBOL SET? OK=YES

3 Enter the number of copies you want as your default setting. Press YES to accept this data into memory.

SYMBOL SET=IBM-US OK=YES / or OT1-23

5. 2 PC Printing & Scanning
Page 111 of the Lanier 2002 user manual — FONT NUMBER=1 OK=YES (DEL=NO)
Page 111 · click to enlarge
Page 111

Set Printer (2002 Only)

Font Number

Allows users to set various font numbers as listed below. Provides six internal fonts that remain resident in the machine. They are listed in the following table by number and size. The machine will use the selected font whenever your computer does not send an override for a different font. This unit also accepts download able fonts that are compatible with the HP PCL4 language that are sent to the printer and then selected by your computer software. Memory limitations can restrict the variety and size of the downloadable fonts.

Font Number Font Pitch Point Orientation

1 Courier 10 12 Portrait

2 Courier Bold 10 12 Portrait

3 Line Printer 16.6 8.5 Portrait

4 Courier 10 12 Landscape

5 Courier Bold 10 12 Landscape

6 Line Printer 16.6 8.5 Landscape

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

SET PRINTER? YES / or 1-8

2 Press 4 or scroll down to the Font Number menu and press YES.

4 FONT NUMBER? OK=YES

3 Enter the number of the font you wish to have as your default print font. Press YES to accept this data into memory.

FONT NUMBER=1 OK=YES (DEL=NO)

PC Printing & Scanning 5 - 3

Page 112 of the Lanier 2002 user manual — Set Printer (2002 Only)
Page 112 · click to enlarge
Page 112

Set Printer (2002 Only)

Font Definitions

Orientation: Portrait text prints across the width of the page. Landscape text prints across the length of the page.

Pitch: Font pitch determines the number of characters printed per inch. A pitch of 12, for example, means that 12 fixed width characters are printed in every inch.

Point Size: Indicates the height of a font. There are 72 points to an inch.

Line Number: Sets the number of text lines on a printed page. If your computer software sends more lines than this setting, they print on a second page.

Print Fonts: Prints a list of resident fonts.

Paper Size: The size of the paper in the PFU Tray.

5. 4 PC Printing & Scanning
Page 113 of the Lanier 2002 user manual — *PRINT FONT*
Page 113 · click to enlarge
Page 113

Set Printer (2002 Only)

Line Number

Allows users to set the total lines for each printed page. You can set any number between 5 and 127 lines per page. Note: In most cases, PC software settings override this setting.

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

SET PRINTER? YES / or 1-8

2 Press 5 or scroll down to the Line Number menu and press YES.

5 LINE NUMBER? OK=YES

3 Enter the number of the lines per page you wish to have as your default. Press YES to accept this data into memory.

LINE NUMBER=_64 OK=YES (DEL=NO)

Print Font

Allows the user to print samples of the fonts resident in the machine for your reference.

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

SET PRINTER? YES / or 1-8

2 Press 6 or scroll down to the Print Font menu and press YES.

6 PRINT FONT? OK=YES

3 The unit prints the list of available fonts. It also gives a sample of each.

*PRINT FONT*

PC Printing & Scanning 5 - 5

Page 114 of the Lanier 2002 user manual — PCL4/GDI CHANGE RESTART YOUR FAX
Page 114 · click to enlarge
Page 114

Set Printer (2002 Only)

PCL4

Allows users to select PCL4 printer emulation which supports 300 dpi. If the LCD displays, “PCL4/GDI CHANGE, RESTART YOUR FAX” because memory reallocation (refer to Memory required for printer” ), it is necessary to power OFF the fax machine and then turn the power back ON (wait approximately 6 seconds before turning unit back ON).

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

SET PRINTER? YES / or 1-8

2 Press 7 or scroll down to the PCL4 Enhance menu and press YES.

7 PCL4 ENHANCE? OK=YES

3 Select either ON or OFF depending on your needs. Press YES to accept this data into memory.

ON *OFF -SELECT&PUSH”YES”-

4 If you chose YES, you must restart your unit to make this change active.

PCL4/GDI CHANGE RESTART YOUR FAX

5. 6 PC Printing & Scanning
Page 115 of the Lanier 2002 user manual — PCL4/GDI CHANGE RESTART YOUR FAX
Page 115 · click to enlarge
Page 115

Set Printer (2002 Only)

GDI Enhance

Allows users to select the GDI printer driver which supports 600 dpi. Additional memory is necessary for printing documents at 600 dpi.

1 Press the PROGRAM Key and scroll through the menus until you reach the Set Printer menu and press YES.

SET PRINTER? YES / or 1-8

2 Press 7 or scroll down to the PCL4 Enhance menu and press YES.

8 GDI ENHANCE? OK=YES

3 Select either ON or OFF depending on your needs. Press YES to accept this data into memory.

ON *OFF -SELECT&PUSH”YES”-

4 If you chose YES, you must restart your unit to make this change active.

PCL4/GDI CHANGE RESTART YOUR FAX

PC Printing & Scanning 5 - 7

Page 116 of the Lanier 2002 user manual — Standard Memory Configuration Choices
Page 116 · click to enlarge
Page 116

Memory Allocations

Memory Allocations

The GDI printer function comes with 6 Mb of memory. If you print complex pages, you might experience memory overflow conditions.

Standard Memory Configuration Choices

User Selection Fax Memory

Memory PCL4 GDI Enhanced

A4/Ltr. Std (Pages)

PCL4 GDI 300 dpi printing

GDI 600 dpi printing

6MB Off Off 576 No Yes No

Off On 384 No Yes Yes*

On Off 297 Yes Yes No

On On 297 Yes Yes Yes

5. 8 PC Printing & Scanning

For Printing

Page 117 of the Lanier 2002 user manual — Connecting to a Computer
Page 117 · click to enlarge
Page 117

PCL4 Emulation (2002 only)

PCL4 Emulation (2002 only)

PCL4 emulation provides 300 dpi resolution, which is adequate for printing text. If you are printing a document that contains several graphics, you might prefer to use the GDI driver, which provides a higher (600 dpi) resolution or the PCL5e option. See “GDI Printer Feature” on page 5-7 for details.

Connecting to a Computer

Follow these instructions to install the cables.

1 Close all the open programs on the PC.

2 Be sure power to the computer and the fax unit are OFF.

3 Connect the parallel cable to the parallel connector (bottom port) on the your unit.

Lanier 2002 — Connecting to a Computer diagram (page 117)
Fig. 18 · Connecting to a Computer

4 Connect the other end of the cables to the parallel port on the PC.

5 Turn power on to both the computer and the fax machine.

PC Printing & Scanning 5 - 9

Page 118 of the Lanier 2002 user manual — Printing Envelopes
Page 118 · click to enlarge
Page 118

PCL4 Emulation (2002 only)

Setting Up the Computer Application Printer Driver

1 From the setup program in your software application, select the HP LaserJet Series II printer type. If you are using optional memory, we recommend you select the HP LaserJet IIP.

  • 2 Set your software applications printer options to match the following items:
  • Match the paper size with the size loaded in your paper cassette.
  • Match the memory size in the driver to that of the your unit. Note: If your software application does not provide HP LaserJet II drivers, you should obtain them from the application vendor.

Basic Operation

This section explains standard printing with the 2002. The display provides information about printer activities.

Using the Manual Feed Tray to Print

Lanier 2002 — Using the Manual Feed Tray to Print diagram (page 118)
Fig. 19 · Using the Manual Feed Tray to Print

Use the Manual Feed Bypass to print on paper that is a different size than the paper you have loaded in the paper cassettes, or for printing on thick paper, such as envelopes. If paper is present in the Tray, the unit automatically selects it.

1 Place the paper on the tray and adjust the Side Guides.

2 Print to the 2002 from your PC.

Printing Envelopes

Follow these steps to print an envelope.

1 In the application, configure the paper size for the envelope.

2 Place the envelope facing down in the manual feed tray with the narrow end leading into the center of the unit.

3 Adjust the Side Guides to the edges of the envelope.

4 Perform the steps in the software application to print.

5. 10 PC Printing & Scanning
Page 119 of the Lanier 2002 user manual — Auto-Select Paper Tray
Page 119 · click to enlarge
Page 119

Printer Messages

Printer Messages

When the unit is on-line and receiving data from the computer, the unit displays messages indicating the printer status.

PC Connection Printer is receiving data from the computer.

Allow unit to complete process before making any adjustments.

Printer Memory Full Memory = 00

There is insufficient memory for the print job.

Wait until other jobs complete making more memory available.

Auto-Select Paper Tray

The auto tray select function gives you a choice between manually selecting a paper tray or letting the unit select the paper tray to print or fax. Follow the instructions in “Setting Auto-Cassette Select (for PFU Tray) on page 6-34 to set up this feature.

PC Printing & Scanning 5 - 11

Message Description Recommendations

Page 120 of the Lanier 2002 user manual — PC Requirements
Page 120 · click to enlarge
Page 120

GDI Printer Feature

GDI Printer Feature

Your 2002 comes with a Windows print driver disk that enables it to function as a 300 or 600 dpi laser printer for Windows applications. The 2002 has both a serial and a parallel port, either of which can be used to connect the unit to your PC for printing. The parallel port is recommended because the speed is faster, and the setup easier.

PC Requirements

These are the minimum PC requirements for using the GDI printer function with Windows 3.1.

OS Windows 3.1, MS-DOS 6.0

CPU Intel 80486 SX 20 MHz

HDD 5 Mb (excluding swap area)

Virtual memory Swap file of 8 Mb

These are the minimum PC requirements for using the GDI printer function with Windows 95.

CPU Intel 80486 DX 33 MHz

HDD 5 Mb (excluding swap area)

5. 12 PC Printing & Scanning

RAM 8 Mb · OS Windows 95 · RAM 8 Mb

Page 121 of the Lanier 2002 user manual — Windows95
Page 121 · click to enlarge
Page 121

GDI Printer Feature

Connecting to Your PC

As stated above, you can use either a serial port or parallel port for the GDI printer function. A serial cable comes with the 2002, but if you decide to use the parallel port, you must purchase a parallel cable. To comply with ECM (RFI-EMI) requirements, this parallel cable should not exceed 6’7” (2 meters), and should have a high-quality shield.

Verify that the parallel cable you are use conforms to the pinout specifications listed below:

Pin Signal Pin Signal Pin Signal Pin Signal

1 -Strobe 10 -Ack 19 GND 28 GND

2 Data 1 11 Busy 20 GND 29 GND

3 Data 2 12 PError 21 GND 30 GND

4 Data 3 13 Select 22 GND 31 -Init

5 Data 4 14 -Auto Feed 23 GND 32 -Fault

6 Data 5 15 N.C. 24 GND 33 N.C.

7 Data 6 16 GND 25 GND 34 N.C.

8 Data 7 17 Chassis 26 GND 35 N.C.

9 Data 8 (MSB)

18 VCC 27 GND 36 -Select In

See “Connecting to a Computer on page 5-3 to connect the parallel printer cable between the 2002 printer port and a parallel port on your computer.

Installing The Printer Driver

These instructions assume that the Windows program is already running. These instructions are also included in a Readme File on the floppy.

Windows95

1 Click the Start button on the task bar.

2 Choose Settings - Printers.

3 In the Printers window, click the Add Printer icon.

4 The Add Printer Wizard opens. Click Next.

5 Choose Local Printer. Click Next.

PC Printing & Scanning 5 - 13

Page 122 of the Lanier 2002 user manual — GDI Printer Feature
Page 122 · click to enlarge
Page 122

GDI Printer Feature

6 A list of printers appears. Click the Have Disk... button.

7 When the dialog box appears, insert the program disk.

8 Click Browse.

9 Select the win95 folder containing the mfd12x0.inf file.

10 Click OK.

11 Click OK on the Install From Disk window.

12 The Add Printer Wizard lists the MFD1210/1260 printer.

13 Select the printer you want and click Next.

  • 14 Select the serial or parallel port to which you have connected the print device.
  • If you are using a parallel port, go to the next step.
  • If you are using a serial port, click Configure Port to configure the PC serial port to match the 2002 printer device. The COMM port configuration for the 2002 is:
  • Click OK .
Baud Rate38400
Data bits8

15 Click Next. Continue to follow the instructions in the Add Printer Wizard.

Flow controlHardware
  • The Wizard copies all necessary files to the PC hard drive and loads the printer driver.
  • During the file copy process, a Copying Files window might appear, instructing you to insert the original Windows 95 installation disk. Check to see if the requested files reside in your Windows system already. To do this, click Browse in the Copying Files dialog window and direct Windows to search for the files in the System directory (c:\windows\system). If the files are not found, insert the Windows 95 disk and instruct the Copying Files dialog to search for the files on the disk.

16 The Add Printer Wizard copies all the necessary files to your hard drive and loads the new printer driver.

5. 14 PC Printing & Scanning

Parity None · Stop bits 1

Page 123 of the Lanier 2002 user manual — GDI Printer Feature
Page 123 · click to enlarge
Page 123

GDI Printer Feature

Windows 3.1

1 On the Program Manager window, click Main - Control Panel - Printers.

2 On the Control Panel Printers window, click Add >>.

3 In the Printers pop-up window, select Install Unlisted or Updated Printer.

4 Click Install.

5 Insert the printer driver disk into the disk drive.

6 Click Browse.

7 On the Browse window, select the \win31 folder.

8 Click OK. The Install Driver window appears.

9 Click OK.

10 The Add Unlisted or Updated Printer window appears. Highlight the 2002 printer selection.

11 Click OK. Windows 3.1 copies all the necessary files to the hard drive and loads the new printer driver.

  • During the file copy process, an Install Driver dialog may appear and instruct you to insert the original Windows 3.1 installation disk to load some required files. The requested files may be in your Windows system already. To find out, click the Browse button on the Install Driver window, then direct Windows to search for the files in the system directory. If the requested files are not found, insert the Windows 3.1 installation disk and instruct the Install Driver dialog to search the disk for the files. If the requested files are already in the system, choose Browse and specify the system directory (ex.: c:\windows\system).

12 Click the Connect button. On the Connect window, select the communication port to which you connected the printer device.

13 If you are using a parallel port, the installation is complete.

PC Printing & Scanning 5 - 15

Page 124 of the Lanier 2002 user manual — GDI Printer Feature
Page 124 · click to enlarge
Page 124

GDI Printer Feature

14 If you are using a serial port, click Settings to configure the PC serial port on the PC to match the 2002 printer device. The COMM port configuration for the 2002 is:

Baud Rate38400
  • The baud rate of the 2002 printer is set at 38400 in the factory. If the drop-down Baud Rate list box doesn’t include a 38400 selection, move the focus to the Baud Rate list and type 38400 in the box.
Data bits8
Flow controlHardware
5. 16 PC Printing & Scanning

Parity None · Stop bits 1

Page 125 of the Lanier 2002 user manual — Getting Help
Page 125 · click to enlarge
Page 125

GDI Printer Feature

Configuring the GDI Print Settings

Configure the settings for the GDI printer function the same as you would for any other printer. Refer to your Windows or software application manual. In most applications, you configure the paper size in the application. To configure the paper source:

  • For the Bypass Tray, place paper in the Bypass. The Bypass paper will be selected first.
  • For the 2nd Cassette, the 2002 will automatically select the correct paper size. If both cassettes are the same size paper, the Top Tray will be selected first. If it runs out of paper, the unit automatically selects the Bottom Tray and continues.

Printing with your GDI Print Function

After you install the GDI print driver, you can select and use it in your Windows applications just as you would any other printer. When you select Print, the file to be printed is spooled inside the PC and then sent to your MFD unit. Printed sheets exit onto the receiving tray.

Getting Help

The on-line help explains all the GDI print driver functions and options.

PC Printing & Scanning 5 - 17

Page 126 of the Lanier 2002 user manual — HD
Page 126 · click to enlarge
Page 126

Scanning (TWAIN Driver Option)

Scanning (TWAIN Driver Option)

The TWAIN software enables your PC to import scanned images from your 2002 unit into your software applications. A serial port connection is required for this to work. See “Attaching the Peripheral Cables” on page 2-4 if you need to connect the cable first. Please Note: This feature is an option on your unit.

PC Requirements for the TWAIN Option

Computer OS Windows 95 Windows 3.1 Windows 3.11 MS-DOS 6.0 or higher

MPU Intel 80486SX 33 MHz or higher

Memory 8 MB or more (Windows 3.1 and 3.11) 16 MB or more (Windows 95)

HD

Installing the TWAIN Driver

On Windows95

1 Insert the TWAIN driver disk in the disk drive.

2 Select Start - Run.

3 On the Run window, type a:\setup.

4 Click OK.

5 The InstallShield wizard window appears. Follow the instructions to load the program.

5. 18 PC Printing & Scanning

Cable RS-232-C

Page 127 of the Lanier 2002 user manual — Scanning
Page 127 · click to enlarge
Page 127

Scanning (TWAIN Driver Option)

On Windows 3.1

1 Insert the TWAIN driver disk in the disk drive.

2 On the Program Manager window, select File - Run.

3 On the Run window, type a:\setup.

4 Click OK.

5 The InstallShield wizard window appears. Follow the instructions to load the program.

Scanning

1 In the PC software program (HiJaak Pro, PaintShop Pro, etc.), click File.

2 Click Select Source. • The Select Source window appears.

3 Choose “Lanier 1210/1260 Scanner” from the dialog box.

4 Click Select.

5 Click File - Acquire.

6 Set the controls in the Scanning Control window.

Paper Size Display Panel

Lanier 2002 — Scanning diagram (page 127)
Fig. 20 · Scanning

7 Place the document you are scanning in the MFD document feeder tray.

8 Click SCAN.

PC Printing & Scanning 5 - 19

Show 7 more labels / short text on this page
Close · Type · Logo · Brightness · Resolution · Scan · Configuration
Page 128 of the Lanier 2002 user manual — Scanning (TWAIN Driver Option)
Page 128 · click to enlarge
Page 128

Scanning (TWAIN Driver Option)

Scanning Control window settings

The Display panel includes the following settings: Type: B/W = for text documents Photo = for gray scale images (photos) Brightness: Normal, light, or dark Paper size: A4, letter, legal, or B5 Resolution: Standard, fine, or ex-fine Configuration: Click this button to display the configuration window. Select a port and a baud rate.

Lanier 2002 — Scanning (TWAIN Driver Option) diagram (page 128)
Fig. 21 · Scanning (TWAIN Driver Option)

The PORT button has four options: COM1, COM2, COM3, or COM4. The Baud rate button has two selections: 38,400 for high-speed communications or 19,200 for lower communication speeds. Logo: Click the logo to display information about this product and access the on-line help window. Scan: Click to start the scanning process. Close: Click this button to close the scanner control panel.

5. 20 PC Printing & Scanning
Page 129 of the Lanier 2002 user manual — Scanning (TWAIN Driver Option)
Page 129 · click to enlarge
Page 129

Scanning (TWAIN Driver Option)

Scanner Troubleshooting

When your unit encounters trouble while scanning, an error message appears on the LCD display. Consult the following table to correct the problem.

Place Original There are no documents in the ADF, or the ADF is in use.

Place your document in the ADF.

Document Jam A document is jammed in the ADF.

Remove the document. Place it back in the ADF.

Communication Error, Check Setting/Scanning Table

The interface cable is not connected or the unit is OFF.

Connect the cable securely. Make sure the power is on. You may need to check and correct the communication settings in the Option menu.

Unable to scan image The unit is performing an operation and is not in the image scanning mode.

Wait for the unit to finish the operation.

Scanning error code:XXXXXX An error occurred during

Reset the computer and your MFD unit.

image scanning.

File access error Captured images cannot be stored.

The destination disk is considered short on available space. Secure space enough to store the images.

PC Printing & Scanning 5 - 21

Message Cause Solution

Page 130 of the Lanier 2002 user manual — PC Requirements
Page 130 · click to enlarge
Page 130

Class 1 Fax/Modem

Class 1 Fax/Modem

The Class 1 fax/modem interface on your unit enables it to function as a Class 1 fax/ modem for any IBM-compatible computer, sending and receiving fax messages directly from your computer. The Class 1 fax/modem interface works with the computer to increase fax efficiency and speed. It works with the commercially available PC-fax software listed below. You can also use the interface to scan and print fax resolution quality documents. The interface works with the following fax software:

  • WinFax Pro V4.01
  • FaxWorks Pro V3.00A
  • Bitfax V3.07
  • LaserFax Class 1 It is possible to use other Class 1 computer software, but Lanier doesn’t guarantee their operation.

Class 1 Interface

The Class 1 interface provides these functions:

  • Fax transmission . A file in the computer can be faxed directly to a remote location. There is no need to print the file and scan it into the fax unit first. The PC fax software directs the file to your fax unit, and your fax unit sends it to the remote fax location.
  • Fax receiving . Your PC can receive a fax from a remote location. The PC-fax software converts the fax into a computer file, and saves it on the computer’s hard drive.
  • Printing . You can send a file from your computer to your fax unit. The fax machine receives the file from the computer and prints the document at standard (100 x 200 dpi), fine (200 x 200 dpi), or superfine (200 x 400 dpi) resolution.
  • Scanning. See page 7-18.

PC Requirements

Your PC must have an available serial COMM port. The computer type (386, 486, etc.), speed, and memory capacity must meet the system requirements for the PC fax software package you have selected. Refer to the PC fax software documentation for system requirements.

5. 22 PC Printing & Scanning
Page 131 of the Lanier 2002 user manual — Using Class 1 Mode
Page 131 · click to enlarge
Page 131

Class 1 Fax/Modem

Connecting Class 1 to Your PC

The 2002 uses a standard RS-232C port to communicate with the PC. A serial cable comes with the 2002 unit. Follow the instructions in “Attaching the Peripheral Cables” on page 2-4 to connect the cable if you have not already connected it. Please Note: This feature is optional on your unit.

Installing the PC-Fax Software

There are a number of settings that affect the modem. This table provides a list of common settings and the preferred Lanier settings.

Modem type Generic Class 1 or Class 1

Dial type Use the type that matches your telephone service. This selection determines whether the dial command is ATDT for tone or ATDP for pulse.

Dial tone detect OFF

Detect busy OFF. Your unit detects a busy signal and provides the correct response. If the remote unit does not answer, the fax unit responds “No carrier” on the computer, which can then schedule a re-dial.

Speaker On/Off and volume OFF

Using Class 1 Mode

  • When your unit communicates with the computer, “CLASS 1 MODE” appears on the LCD.
  • No other fax activities can be performed while the MFD communicates with the PC.
  • During a fax operation initiated by your unit, a fax request initiated by the PC is not processed.
  • The maximum fax transmission speed is 14,400 bps in Class 1 mode.

PC Printing & Scanning 5 - 23

Flow control Xon/Xoff

Page 132 of the Lanier 2002 user manual — Scanning in Class 1 Mode
Page 132 · click to enlarge
Page 132

Class 1 Fax/Modem

Sending a Fax in Class 1 Mode

Follow these steps to send a fax from your computer to a remote location

1 From the computer, select the file you are sending.

2 Enter the remote fax telephone number.

3 Start the send operation from the PC, according to the PC-fax software instructions.

Receiving a Fax in Class 1 Mode

  • PC RX must be set to ON (see “PC RX mode (ON/OFF) on page 6-35 in Chapter 6 for instructions). (Default = ON)
  • The computer must be on.
  • The PC-fax software must be running and set to auto-answer.
  • Your unit routes the incoming call to the computer.

Scanning in Class 1 Mode

To scan a document from your unit into your PC-fax application, you must use your Class 1 ID number for the destination. You must enter your ID number exactly as it is programmed. (Default = 999) Instructions for programming the Class 1 ID number are included on a gray, perforated page in this manual. These instructions should be removed from this manual immediately and stored in a secure place to prevent unauthorized use. Follow these steps to scan a fax into your computer:

1 Make sure the computer is on.

2 Make sure the PC-fax software is running and set to auto-answer mode.

3 Load the document in the ADF.

4 Select the highest available resolution to assure the best print quality.

5 Enter your Class ID number as the destination. Enter this number in one of the following ways:

  • Use your MFD keypad to enter your fax phone number.
  • Pre-program your fax phone number into a one-touch or speed dial location. Use this one-touch or speed dial to enter the destination.

6 Your unit scans the document into memory, then faxes the document to the computer.

5. 24 PC Printing & Scanning
Page 133 of the Lanier 2002 user manual — Class 1 Fax/Modem
Page 133 · click to enlarge
Page 133

Class 1 Fax/Modem

Printing in Class 1 Mode

To print a document to your unit from the PC-fax application. you must use the Class 1 ID number as the destination. Enter the Class ID number exactly as it is programmed. Follow these steps to use your unit as a printer:

1 In the PC-fax software application, enter the Class 1 ID number in the telephone number field.

2 If the PC-fax software application allows, you can enter a single hyphen for the phone number instead of the Class 1 ID number.

3 When your unit receives the destination telephone number (the Class 1 ID number) from the PC, it recognizes the number as its own and prints the document instead of forwarding it to another location.

PC Printing & Scanning 5 - 25

Page 134 of the Lanier 2002 user manual — Class 1 Fax/Modem
Page 134 · click to enlarge
Page 134

Class 1 Fax/Modem

Notes:

5. 26 PC Printing & Scanning
Page 135 of the Lanier 2002 user manual — Chapter 6
Page 135 · click to enlarge
Page 135

Chapter 6

Maintenance & Supplies

Page 136 of the Lanier 2002 user manual — Chapter Overview
Page 136 · click to enlarge
Page 136

Chapter Overview

This chapter contains the description of maintenance functions normally performed by the Key Operator. Contained in this Chapter are:

  • Loading Paper
  • Clearing Paper Jams
  • Changing the Toner Cartridge
  • Changing the Drum Cartridge
  • Cleaning your unit.

Maintenance & Supplies

Page 137 of the Lanier 2002 user manual — Loading the Paper
Page 137 · click to enlarge
Page 137

Loading the Paper

Loading the Paper

Paper Tray

1 Remove the Paper Tray Cover.

Lanier 2002 — Loading the Paper diagram (page 137)
Fig. 22 · Loading the Paper

2 Fan the paper stack thoroughly and align its edges.

3 When loading paper other than Letter size, adjust the Paper End Stop to fit the paper length. It should just touch the end of the paper.

Maintenance & Supplies 6 - 1

Page 138 of the Lanier 2002 user manual — Optional PFU Paper Cassette
Page 138 · click to enlarge
Page 138

Loading the Paper

4 Load paper onto the Tray and adjust the Alignment Guides to touch the sides of the paper.

Lanier 2002 — Loading the Paper diagram (page 138)
Fig. 23 · Loading the Paper

Optional PFU Paper Cassette

Lanier 2002 — Optional PFU Paper Cassette diagram (page 138)
Fig. 24 · Optional PFU Paper Cassette

1 Lift the PFU Cassette slightly and pull to remove it from the machine.

2 Remove the Cassette Cover and press down on the Paper Lifting Plate.

6. 2 Maintenance & Supplies
Page 139 of the Lanier 2002 user manual — Loading the Paper
Page 139 · click to enlarge
Page 139

Loading the Paper

3 Fan the paper stack thoroughly and align its edges. Load the paper stack on the tray.

Lanier 2002 — Loading the Paper diagram (page 139)
Fig. 25 · Loading the Paper

4 DO NOT place paper above the Maximum Paper Level indicator.

Lanier 2002 — Loading the Paper diagram (page 139)
Fig. 26 · Loading the Paper

5 Replace the Cassette Cover and insert it into the machine.

Lanier 2002 — Loading the Paper diagram (page 139)
Fig. 27 · Loading the Paper

Maintenance & Supplies 6 - 3

Page 140 of the Lanier 2002 user manual — Document Jams
Page 140 · click to enlarge
Page 140

Clearing Paper Jams

Clearing Paper Jams

The facsimile machine has two different messages for paper jams. The message “ORIGINAL DOC. JAM” indicates a problem in the Scanner section. The message “RECORDING PAPER JAM” indicates a problem with the printer paper path.

Document Jams

When a document jam occurs, the message “ORIGINAL DOC. JAM” appears on the LCD. To remove the jam, follow the procedure below.

1 Open the Scanner Cover and remove the jammed documents.

Lanier 2002 — Document Jams diagram (page 140)
Fig. 28 · Document Jams

2 Open the ADF Cover and remove the jammed documents.

6. 4 Maintenance & Supplies
Page 141 of the Lanier 2002 user manual — Clearing Paper Jams
Page 141 · click to enlarge
Page 141

Clearing Paper Jams

Paper Jams

When a paper jam occurs, the message ‘RECORDING PAPER JAM” appears in the LCD Display.

1 Press the Cover Lock Release Buttons on the left and right side of the Printer Cover, and swing open the Cover.

Lanier 2002 — Clearing Paper Jams diagram (page 141)
Fig. 29 · Clearing Paper Jams

2 Remove the used Toner Cartridge from the fax machine.

3 Remove the Drum Cartridge from the fax machine.

4 Check the paper feed area, the paper exit area, and the area under the Drum and Toner Cartridges for paper. Continue with one of the following procedures to remove the jam.

Maintenance & Supplies 6 - 5

Page 142 of the Lanier 2002 user manual — Jam at Paper Exit Tray
Page 142 · click to enlarge
Page 142

Clearing Paper Jams

Jam at the Paper Feed Tray Cover

1 Pull out the paper in the direction shown by the arrow.

Lanier 2002 — Clearing Paper Jams diagram (page 142)
Fig. 30 · Clearing Paper Jams

Jam at the Paper Feed Tray

1 Remove the Tray Cover and pull out the paper in the direction shown by the arrow.

Lanier 2002 — Jam at the Paper Feed Tray diagram (page 142)
Fig. 31 · Jam at the Paper Feed Tray

Jam at Paper Exit Tray

1 If the paper is caught by the Fusing Unit, remove the paper by pulling it toward you as shown by the arrow.

Lanier 2002 — Jam at Paper Exit Tray diagram (page 142)
Fig. 32 · Jam at Paper Exit Tray
6. 6 Maintenance & Supplies
Page 143 of the Lanier 2002 user manual — Jam at the PFU Cassette
Page 143 · click to enlarge
Page 143

Clearing Paper Jams

Jam between the Feeding Rollers and Fuser Unit

1 Pull out the paper from the Fuser Unit in the direction shown by the arrow.

Lanier 2002 — Clearing Paper Jams diagram (page 143)
Fig. 33 · Clearing Paper Jams

2 Pull out the paper from the Feed Roller in the direction shown by the arrow.

Jam at the PFU Cassette

1 Remove the PFU Cassette.

2 Pull out the paper from the Feed Roller in the direction shown by the arrow.

3 Re-install the PFU Paper Cassette into the PFU.

Maintenance & Supplies 6 - 7

Page 144 of the Lanier 2002 user manual — Clearing Paper Jams
Page 144 · click to enlarge
Page 144

Clearing Paper Jams

After removing the jam follow these steps:

1 Install the Drum Cartridge making sure the color tabs fit into the slots.

Lanier 2002 — Clearing Paper Jams diagram (page 144)
Fig. 34 · Clearing Paper Jams

2 Install the Toner Cartridge Making sure the color tabs fit into the slots.

3 Gently press down the Printer Cover and securely close it.

6. 8 Maintenance & Supplies
Page 145 of the Lanier 2002 user manual — Changing Toner Cartridge
Page 145 · click to enlarge
Page 145

Changing Toner Cartridge

Changing Toner Cartridge

1 Press the Cover Lock Release Buttons on the left and right side of the Printer Cover, and swing open the Cover.

Lanier 2002 — Changing Toner Cartridge diagram (page 145)
Fig. 35 · Changing Toner Cartridge

2 Remove the used Toner Cartridge from the fax machine.

3 Take the new Toner Cartridge out of its carton, Before installing the Toner Cartridge, it si necessary to evenly distribute the toner inside of the Cartridge. Hold the Toner Cartridge with both hands, and shake it in the direction of the arrows.

4 Install the new Toner Cartridge. Make sure the four pins of the Toner Cartridge (two each at the front and rear sides) fit in the slits inside the fax machine.

Maintenance & Supplies 6 - 9

Page 146 of the Lanier 2002 user manual — Changing Drum Cartridge
Page 146 · click to enlarge
Page 146

Changing Toner Cartridge

5 Gently press down the Scanner Cover, and securely close it.

Lanier 2002 — Changing Toner Cartridge diagram (page 146)
Fig. 36 · Changing Toner Cartridge

Changing Drum Cartridge

1 Press the Cover Lock Release Buttons on the left and right side of the Printer Cover, and swing open the Cover.

Lanier 2002 — Changing Drum Cartridge diagram (page 146)
Fig. 37 · Changing Drum Cartridge

2 Remove the used Toner Cartridge from the fax machine.

6. 10 Maintenance & Supplies
Page 147 of the Lanier 2002 user manual — Changing Toner Cartridge
Page 147 · click to enlarge
Page 147

Changing Toner Cartridge

3 Remove the Drum Cartridge.

Lanier 2002 — Changing Toner Cartridge diagram (page 147)
Fig. 38 · Changing Toner Cartridge

4 Take the new Drum Cartridge out of its carton and install it. Make sure to align the tabs with the slots and match blue and green color coding.

5 Install the Toner Cartridge. Make sure the four pins of the Toner Cartridge (two each at the front and rear sides) fit in the slits inside the fax machine.

6 Gently press down the Scanner Cover, and securely close it.

Maintenance & Supplies 6 - 11

Page 148 of the Lanier 2002 user manual — Cleaning the Scanner
Page 148 · click to enlarge
Page 148

Maintenance

Maintenance

Cleaning Your Fax Unit

It is important to take routine care of your fax machine to keep it in optimum operating condition.

1 Using a soft cloth dampened with mild detergent, wipe the outside of the fax machine.

Lanier 2002 — Maintenance diagram (page 148)
Fig. 39 · Maintenance

Cleaning the Scanner

1 Open the Scanner Cover.

Lanier 2002 — Cleaning the Scanner diagram (page 148)
Fig. 40 · Cleaning the Scanner

2 Gently wipe the glass of the image sensor.

6. 12 Maintenance & Supplies
Page 149 of the Lanier 2002 user manual — Maintenance
Page 149 · click to enlarge
Page 149

Maintenance

Lanier 2002 — Maintenance diagram (page 149)
Fig. 41 · Maintenance

3 Wipe the roller clean of dirt and paper dust with a soft cloth.

Maintenance & Supplies 6 - 13

Page 150 of the Lanier 2002 user manual — Maintenance
Page 150 · click to enlarge
Page 150

Maintenance

Notes:

6. 14 Maintenance & Supplies
Page 151 of the Lanier 2002 user manual — Chapter 7
Page 151 · click to enlarge
Page 151

Chapter 7

Troubleshooting

Page 152 of the Lanier 2002 user manual — Chapter Overview
Page 152 · click to enlarge
Page 152

Chapter Overview

This chapter contains some basic troubleshooting measures. These should be tried prior to calling for service.

Troubleshooting

Page 153 of the Lanier 2002 user manual — Error Indication Types
Page 153 · click to enlarge
Page 153

Troubleshooting

Troubleshooting

If your fax unit does not work properly, please refer to the following information to fix some problems you might encounter before contacting your service representative. However, if the problem still cannot be corrected, do not attempt further repairs. Turn OFF your unit and consult your Service Representative. Never disassemble or try to fix your fax unit on your own, as you could damage it and suffer risk of electric shock.

Error Indication Types

The fax unit warns you of an error or malfunction with the LED, ALARM or messages detailed below. These pages cover the meaning of the LED, ALARM, and messages, together with action you can take to correct the problem.

LED Indication Description Action

LED ON (Machine Trouble) A minor malfunction has occurred.

Follow the instructions on the display.

LED Blinking (Machine trouble) A malfunction has occurred.

Call your Service Representative.

Alarm Beeps Description Action

Three short intermittent beeps.

An incorrect key has been pressed.

Press the correct key.

Short intermittent beeps lasting for 3 seconds.

A communications error has occurred.

Follow the instructions on the display.

Continued short beeps. Handset is not placed on the cradle after communication.

Correctly place the handset on the cradle.

Twenty intermittent beeps. (Machine trouble) A malfunction has occurred in the machine.

Call your Service Representative.

Troubleshooting 7 - 1

Page 154 of the Lanier 2002 user manual — *CAUTION* ORIGINAL DOC. JAM
Page 154 · click to enlarge
Page 154

Troubleshooting

Error Messages

The most commonly encountered messages are listed below. Review the cause or symptom of each message and then take the necessary action. For any other messages, follow the instructions that appear on the LCD.

*NO M-BOX FUNCTION* • The fax unit on the receiving side is not equipped with the mailbox function.

  • Cancel mailbox TX and retry transmission.
  • The paper feeding tray or second paper feeding tray has run out of paper.
  • Add Paper.

*CAUTION* NO PAPER

*CAUTION* NO TONER

  • Toner Cartridge is not installed properly or Cartridge is missing.
  • Re-install Toner Cartridge properly or install a new Toner Cartridge.

*CAUTION* MACHINE TROUBLE

  • (Machine trouble) A fault has occurred in the machine.
  • Call your Service Representative.
  • While the fax was receiving a document during mailbox RX, memory RX or Substitute RX the memory became full and facsimile machine is unable to store additional documents into memory.
  • Press the STOP Key and print any documents stored in memory. When memory is available, request the other party to retry the transmission.
  • While your fax was scanning a document for Memory TX, the Memory became full and the fax was unable to send the entire document using Memory TX.
  • To transmit the portion of the document that has been scanned into memory, press the START Key. To increase the memory capacity of the fax machine, print out any documents that were received into memory or wait until other memory transmission jobs are completed. Then retry your Memory TX.
  • To cancel what has been scanned into memory, press the YES key. To increase the memory capacity of the fax machine, print out any documents that were received into memory or wait until any other memory transmission jobs are completed. Then retry your Memory TX.

*CAUTION* MEMORY FULL

  • A document jam has occurred.
  • Clear the misfeed or jam by following the procedures given in “Clearing Document Jams.”

*CAUTION* ORIGINAL DOC. JAM

*CAUTION* PRINT COVER OPEN

  • The fax machine Cover is open or loose.
  • Lock the fax machine Cover in position.
7. 2 Troubleshooting

Message Cause/Symptom Action

Page 155 of the Lanier 2002 user manual — *WRONG PAGE COUNT*
Page 155 · click to enlarge
Page 155

Troubleshooting

  • A recording paper jam has occurred.
  • Clear the jam by following the procedure given in “Clearing Paper Jams.”

*CAUTION* RECORD PAPER JAM

*CAUTION SCAN COVER OPEN

  • The Scanner Cover (Control Panel) is open or loose.
  • Close the Scanner Cover.
  • The fax is almost out of Toner.
  • Replace the Toner Cartridge with a new one. If you leave it without replacing, printed image might be light.

*CAUTION* TONER NEAR EMPTY

*CAUTION* TONER EMPTY

  • The fax unit has run out of toner.
  • Change the Toner Cartridge.
  • An error has occurred and communication was unsuccessful.
  • At transmission: Press the STOP Key, then try another transmission sequence.
  • At reception: Press the STOP Key then ask the other party to try another transmission.

*COMM. ERROR*

  • There is no destination information programmed in the One-Touch Key or Speed Dial number you have just pressed.
  • Select the One-Touch Key or Speed Dial number which contains the information of the destination you are trying to send.

*NOT REGISTERED*

  • The document has not been transmitted to the other party even through repeated auto re-dial attempts.
  • Press the STOP Key, check the fax number, then try another transmission sequence.

*REDAIL ALL FAILED*

*MAILBOX ID IS USED* • The Mailbox ID entered has been previously assigned.

  • Enter a new Mailbox ID.
  • The Mailbox ID specified by the other party does not match the Mailbox ID programmed in your fax.
  • Advise the other party of the correct Mailbox ID and ask them to retry the transmission or ask the party to cancel Mailbox TX and retry transmission.

*WRONG MAILBOX ID*

  • The number of pages of the document transmitted does not equal the number of pages set with page count TX.
  • Check the number of pages again and retry the transmission.

*WRONG PAGE COUNT*

*CHECK LINE* • After several attempts, transmission is unsuccessful.

  • Check to make sure telephone line is properly connected to the fax machine and the wall jack.

*NO INITIATE FUN* • Remote machine not compatible with your machine.

  • Check the other party fax machine.

Troubleshooting 7 - 3

Message Cause/Symptom Action

Page 156 of the Lanier 2002 user manual — *CAUTION* GDI ENHANCE NOT SET
Page 156 · click to enlarge
Page 156

Troubleshooting

  • Remote side memory not enough to save entire document for transfer to other party.
  • Remote machine not compatible with your machine.
  • Try again when remote side fax memory is available.

*RX SIDE/MEM.FULL*

  • Check the other party’s fax machine.

FILE IS FULL FILE FULL / TX CANCEL FILE FULL / RX CANCEL

  • Memory is not available.
  • Wait until memory is available.

REMAILING DATA

  • There is data from PC (using PCL-4 emulation) in fax memory.
  • Press the COPY Key to print out the remaining data in the memory.

PUSH COPY KEY

  • GDI ENHANCE printing mode not set or memory not available.
  • Select GDI ENHANCE printing (refer to set printer session).
  • Call your Service Representative for possible memory upgrade required.

*CAUTION* GDI ENHANCE NOT SET

7. 4 Troubleshooting

Message Cause/Symptom Action

Page 157 of the Lanier 2002 user manual — Troubleshooting
Page 157 · click to enlarge
Page 157

Troubleshooting

Troubleshooting Tips

Here are some tips for troubleshooting our fax. First, take the actions shown below. However, if the problem persists, call your Service Representative.

  • 1 Nothing is shown on the Display.
  • make sure the Power Cord is plugged in properly.
  • Check the Main ON/OFF Switch to make sure it is in the ON position.
  • Check another electric appliance to the AC outlet to check whether the outlet is live.

2 Nothing printed on the receiving side.

  • Make a local copy to check if your machine has amy problem.
  • Make sure the recording paper is properly loaded in the remote receiving unit.

3 The machine fails to enter the reception mode when it is called.

  • Check whether the machine is in the automatic reception mode.
  • Check whether paper is empty or the memory is full.

4 Automatic Document Feeder fails to work.

  • Check the document size.
  • Make sure the documents are properly placed in the Feeder.

5 When the reception image has black stripes.

  • Use your fax to make a copy of the document.
  • If the copied document does not have black stripes, ask the transmitting side to check their machine.
  • If the copied document has black stripes, contact service personnel.

6 No sound can be heard from the telephone set.

  • Check if the Telephone Cord is correctly connected to the terminal of the fax.
  • Check if the Line Cord is connected correctly.
  • 7 Communication error.
  • Most errors are caused by bad line connections, so please retry.
  • Test with another fax machine. If this problem still exists, please contact your service representative.
  • 8 The image received is not clear.
  • Make a copy of another original with a clear image to check the image quality.
  • If the copy is clear: the telephone line or the fax machine of the other party is probably at fault. Ask the other party to re-transmit the document.

9 The image is slanted on the page when you make a copy or receive a document.

  • Re-adjust the Guide in the Paper Cassette.

10The copy quality is poor. • If any black lines appears on the page, please clean the surface of the scanning head under the Control Panel. If the image become faint or blurry, please remove the toner set and rock it.

11The pages come out wrinkled or there are frequent paper jams or double feeding.

  • Check if the paper size and type fit your fax.
  • Check if the paper you are using is rippled or creased.

Troubleshooting 7 - 5

Symptom Action

Page 158 of the Lanier 2002 user manual — Troubleshooting
Page 158 · click to enlarge
Page 158

Troubleshooting

12Your machine print out quality is degrading.

  • Replace the Drum Assembly.

13The image received is skewed. • Ask the other party to retry transmission. The document may have been fed incorrectly at the TX machine.

14A document you transmitted to another party was not received clearly.

  • Make a copy of the document transmitted to check for image quality.
  • If the copy is not clear, clean the contact image sensor of the Scanner of your fax. If still not clear, your fax may need service.
  • If the copy is clear, the telephone line or the fax machine of the other party is probably faulty. Re-transmit the document to check the image quality.
7. 6 Troubleshooting

Symptom Action

Page 159 of the Lanier 2002 user manual — Chapter 8
Page 159 · click to enlarge
Page 159

Chapter 8

Specifications

Page 160 of the Lanier 2002 user manual — Chapter Overview
Page 160 · click to enlarge
Page 160

Chapter Overview

This chapter contains technical specifications for your 2001 and 2002 units.

The specifications listed are for both unless noted specifically.

Specifications are subject to change without notice.

Specifications

Page 161 of the Lanier 2002 user manual — Electrical Specifications
Page 161 · click to enlarge
Page 161

Physical Specifications

Physical Specifications

Style Desktop - Plain paper fax, with optional 500 sheet cassette, PC- printer, PC-scanner, PC-fax and network printer

Printing System Electrostatic transfer and laser printing

Exposure system Contact Image Sensor (CIS), 2592-bits (2552-bits effective)

Photo Conductor Organic Photo Conductor Drum (OPC)

Fusing Hot roll fusing

Dimensions Standard UnitBasic Unit With Handset With Trays extended W/O PFU With PFU

Width = 432 mm (17.0 inches) Width = 508 mm (20.0 inches) Depth = 787 mm (31.0 inches) Height = 432 mm (17.0 inches) Height = 559 mm (22.0 inches)

Weight Standard Unit(w/o PFU)

14 kg (30.87 pounds)

Fax machine AC Power Cord Drum Toner Cartridge Document Entrance Tray

Document Exit Tray Telephone Line Cord User Guide Paper Exit Tray GDI Driver (Floppy - 2002 only)

Electrical Specifications

Power range 120 Vac (102-127Vac), 50/60 Hz, +2% 230 Vac (198 - 264 Vac), 50/60 Hz +2%

Power Consumption Operation Standby

600 W (or less) 30 W

Specifications 8 - 1

Master Carton Contents

Page 162 of the Lanier 2002 user manual — Operational Specifications
Page 162 · click to enlarge
Page 162

Operational Specifications

Operational Specifications

Warm-up time Approximately 20 seconds

Copy Quantity Select 1 to 99

Recommended Volume Maximum: 3,000 documents/month (36,000 prints/month) - TX, Copy, Scan 3.000 prints/month (36,000 prints/year) - RX, Coy, Print

Average: 1,400 documents/month (16,800 prints/year) - TX, Copy, Scan 1.400 Prints/month (16,800 prints/year - RX, Copy, Print

Recording Paper Capacity / Sizes

Standard Cassette Optional PFU Manual Feed Tray

250 sheets, A4, Letter, Legal 500 sheets, A4, Letter Single Sheet, A4, Letter, Legal, Transparency, Executive Envelope 200 sheets, face down

Cassette, recommended acceptable Manual Feed

20 lb (75 g/m2), A4, Letter, Legal 16-24 lb (60-105 g/m2), A4, LT, LG 16-24 lb (60-105 g/m2), A4, LT, LG

A4206 mm Letter (LT)208 mm Legal (LG)208 mm A4291.0 mm Letter LT)273.4 mm Legal (LG)349.6 mm

Speed 8 ppm, Letter/A4 size page

600 dpi Standard3.85 lines/mm Fine7.7 lines/mm Ex-fine15.4 lines/mm, 300 dpi 600 dpi

Supplies Toner CartridgeEP (Drum) Cartridge:

6.000 prints @ 5% B/W ratio 20.000 prints, average

8. 2 Specifications
Show 6 more labels / short text on this page
Exit Tray Capacity · Recommended Paper Weights · Print Effective Width · Effective Length · Resolution Horizontal Vertical · PC-print
Page 163 of the Lanier 2002 user manual — Operational Specifications
Page 163 · click to enlarge
Page 163

Operational Specifications

Contact Image Sensor (CSI), 2592-bits, (2552-bits effective) 208.6 mm (8.2 inches) - 215.4 mm (8.38 inches) 128 mm (5 inches) - 356 mm (14 inches) 380 mm (14.9 inches) Can be extended to 1000mm(39.4 inches)

Effective Length Long Document

Document Feed Tray Capacity

50 sheets, face down, 20 lb. (75 g/m2) A4, Letter.

Range 30 sheets, face down, 16 to 28 lb (60 to 105 g/m2) A4, Letter, Legal

Document Width MinimumA5 (148mm) Maximum: 11 inches
300 dpi Standard3.8 dots/mm Fine:7.7 dots/mm Ex-Fine:15.4 dots/mm Scan:300 dpi

Specifications 8 - 3

Scanner Optical system · Effective Width · Resolution, Horizontal Vertical

Page 164 of the Lanier 2002 user manual — Class 1 Interface (RS-232)
Page 164 · click to enlarge
Page 164

Operational Specifications

Facsimile Specifications

Dialing Functions Phone System PSTN (Public Switched Telephone Network) PABX (Private Branch Exchange)

Dial Type DTMF (Dual Tone Multi Frequency) DP (Dial Pulse: 10pps, 16pps or 20pps)

Direct Dial Keypad Numeric Keypad

One-Touch Dial 64 One-Touch Keys

Auto Dial 200 Locations

Group Dial 64 Groups (One-Touch or Auto Dial)

Protocol Group 3 ITU-T with ECM Class 1 (Optional)

G3: MH, MR, MMR, JBIG, V.34, V.17, V.29

Transmission Speed Standard Resolution 2.5 seconds @ 33,600 (ITU test letter)

Optional Accessories Specifications

Class 1 Interface (RS-232)

Hardware Pin Specification TX, RX, CTS, RTS, DTR/TSR, GND

Connection Speed Auto Baud Rate 2400, 9600, 19200, 38400

Data Bits 1 Start, 8 Data, No Parity, 1 Stop

Communication Speed V.27, V.29, V.17

Flow ControlHardware CTS/RTS
8. 4 Specifications

Compression Modulation · Modem 33,600 bps · Software DC1/DC3 (XON/XOFF)

Page 165 of the Lanier 2002 user manual — LAN Interface (Print Server)(2002 Only)
Page 165 · click to enlarge
Page 165

Operational Specifications

PC Interface

Functions PCL4, GDI, TWAIN, CLASS1, Lan Printer, Remote Monitor, Local F/W Download

PCL4 GDI Class 1 Twain

Unnecessary Standard Unnecessary Optional

Parallel Parallel/Serial Serial Serial

Hardware Interface ParallelOne Direction Parallel Port Serial: RS232-C-Din type NIC Interface

Class 1 1. WinFax Pro V4.01 2. BitFax V3.07 3. Faxwork Pro V3.00a 4. LaserFax generic Class 1 Driver

Twain 1. PhotoShop 2. ImagePAL

PCL4 HP LaserJet Series II

LAN Interface (Print Server)(2002 Only)

Protocols NetWare, TCI/IP, SMB (Service Messafe Block), AppleTalk (EtherTalk), NetBEUI

Network Support 10BaseT, 10Base2 and 10Base T, 10BaseT and 100BaseT

SNMP Support TCP/IP Monitor, Configure, Troubleshoot

Jet Admin Support HP JetAdmin

Specifications 8 - 5

Show 4 more labels / short text on this page
Software Drivers Interface · Recommended Software/ Driver · Web-based Interface TCP/IP · Internet Printing
Page 166 of the Lanier 2002 user manual — Operational Specifications
Page 166 · click to enlarge
Page 166

Operational Specifications

Dual Line

Dialing Functions Phone System PSTN (Public Switched Telephone Network) PABX (Private Branch Exchange)

Dial Type DTMF (Dual Tone Multi-Frequench) DP (Dial Pulse: 10pps, 16pps, or 20pps)

One-Touch Dial 64 One-Touch Keys

Auto Dial 200 Locations

Group Dial 64 Groups (One-Touch or Auto Dial)

Protocol Group 3 ITU-T with EXM Class 1 (Optional)

Compression Modulation G3MH, MR, MMR, JBIG, V.34, V.17, V.29

Transmission Speed Standard Resolution:2.5 seconds @ 33,600 (ITU test letter)

8. 6 Specifications

Direct Dial Keypad · Numberic Keypad · Modem 33,600 bps

Page 167 of the Lanier 2002 user manual — Lithium Battery Statement
Page 167 · click to enlarge
Page 167

Environmental Specifications

Environmental Specifications

Temperature 10 - 330 C (50 - 950 F)

Relative Humidity (RH) Minimum 15%

Operating Altitude Maximum2500 meters (8020 feet) or below

Lithium Battery Statement

Lithium batteries have a danger of explosion. Replace the battery only with the type recommended by the manufacture.

Specifications 8 - 7

Maximum 85% non-condensing

Page 168 of the Lanier 2002 user manual — Environmental Specifications
Page 168 · click to enlarge
Page 168

Environmental Specifications

Notes:

8. 8 Specifications
Page 169 of the Lanier 2002 user manual — Appendix A
Page 169 · click to enlarge
Page 169

Appendix A

Unpacking & Installation

Page 170 of the Lanier 2002 user manual — Unpacking & Installation
Page 170 · click to enlarge
Page 170

Unpacking & Installation

Page 171 of the Lanier 2002 user manual — Main Carton Contents
Page 171 · click to enlarge
Page 171

Unpacking

Unpacking

This Appendix contains the information necessary to unpack and install your unit.

Main Carton Contents

Unpack the carton and verify that the following items are included and undamaged: 1. Toner Cartridge

2. Accessories Box
3. Packing Material
Lanier 2002 — Main Carton Contents diagram (page 171)
Fig. 42 · Main Carton Contents
4. Facsimile Unit
5. Protective Bag
6. Packing Material
7. Shipping Carton
8. Packing Material
9. Drum Cartridge
10. Telephone Handset

Unpacking & Installation A - 1

Page 172 of the Lanier 2002 user manual — Unpacking
Page 172 · click to enlarge
Page 172

Unpacking

Accessories Box Contents

1. Accessory Carton
2. Document Feed Tray
Lanier 2002 — Unpacking diagram (page 172)
Fig. 43 · Unpacking
3. Paper Exit Tray
4. Document Exit Tray
5. Polyethylene Bag
6. Operator Guide
7. Telephone Cord
8. AC Power Cord

A - 2 Unpacking & Installation

Page 173 of the Lanier 2002 user manual — Installing the Drum Cartridge
Page 173 · click to enlarge
Page 173

Setting Up Fax Unit

Setting Up Fax Unit

Removing the Packing Materials

1 Remove the shipping tape.

Lanier 2002 — Setting Up Fax Unit diagram (page 173)
Fig. 44 · Setting Up Fax Unit

2 Remove the Control Panel protective covering.

3 Press the Cover Release Buttons on the left and right sides of the Printer Cover, and swing open the cover.

Installing the Drum Cartridge

Lanier 2002 — Installing the Drum Cartridge diagram (page 173)
Fig. 45 · Installing the Drum Cartridge

2 Install the Drum Cartridge. The ends of the Cartridge and the slots of the unit are color coded. Match the Green to Green and the Blue to Blue when inserting the Cartridge.

Unpacking & Installation A - 3

Page 174 of the Lanier 2002 user manual — Setting Up Fax Unit
Page 174 · click to enlarge
Page 174

Setting Up Fax Unit

Installing the Toner Cartridge

1 Unpack the Toner Cartridge.

Lanier 2002 — Setting Up Fax Unit diagram (page 174)
Fig. 46 · Setting Up Fax Unit

2 Hold the Toner Cartridge with both hands and shake the Cartridge in all directions to assure the toner inside the cartridge is even.

3 Install the Toner Cartridge. The ends of the Cartridge and the slots of the unit are color coded. Match the Green to Green and the Blue to Blue when inserting the Cartridge..

4 Close the Printer Cover and press down to lock it into position.

A - 4 Unpacking & Installation

Page 175 of the Lanier 2002 user manual — Installing the Document Feed Tray
Page 175 · click to enlarge
Page 175

Setting Up Fax Unit

Installing the Paper Exit Tray

1 Insert the two tabs into the corresponding slots inside the unit.

Lanier 2002 — Setting Up Fax Unit diagram (page 175)
Fig. 47 · Setting Up Fax Unit

Installing the Document Exit Tray

1 Insert the two tabs into corresponding slots located just below the front of the Control Panel.

Installing the Document Feed Tray

1 Insert the two tabs into the corresponding slots beside the Control Panel.

Lanier 2002 — Installing the Document Feed Tray diagram (page 175)
Fig. 48 · Installing the Document Feed Tray

2 Press down firmly but evenly until they snap into place.

Unpacking & Installation A - 5

Page 176 of the Lanier 2002 user manual — Attaching the PC Cables
Page 176 · click to enlarge
Page 176

Setting Up Fax Unit

Attaching the Power Cord and Telephone Cords

1 Make sure the Main ON/OFF Switch is in the OFF position.

Lanier 2002 — Setting Up Fax Unit diagram (page 176)
Fig. 49 · Setting Up Fax Unit

2 Connect one end of the Power Cord to the Power Cord Receptacle on the Fax unit.

3 Plug the other end into the wall receptacle.

4 Connect the Telephone line cable to the LINE jack (lower of the two) on the back of the Fax unit.

5 Connect the (Optional) Handset or another external telephone to the TEL jack (upper of the two) on the back of the Fax unit.

Attaching the PC Cables

Lanier 2002 — Attaching the PC Cables diagram (page 176)
Fig. 50 · Attaching the PC Cables

1 Insert the end of the Printer Cable and/or RS-232 Cable into the appropriate connectors on the back of the Fax unit.

A - 6 Unpacking & Installation

Page 177 of the Lanier 2002 user manual — Setting Up Fax Unit
Page 177 · click to enlarge
Page 177

Setting Up Fax Unit

Installing the Handset

1 Assemble the Bracket and the Handset Holder with two screws.

Lanier 2002 — Setting Up Fax Unit diagram (page 177)
Fig. 51 · Setting Up Fax Unit

2 Install the Handset Holder to the Fax unit with two screws.

3 Connect the Handset Cable into the connector on the back of the Fax unit labeled TEL.

Unpacking & Installation A - 7

Page 178 of the Lanier 2002 user manual — Setting Up Fax Unit
Page 178 · click to enlarge
Page 178

Setting Up Fax Unit

Loading Paper

1 Remove the shipping tape from the Tray Cover.

Lanier 2002 — Setting Up Fax Unit diagram (page 178)
Fig. 52 · Setting Up Fax Unit

2 Remove the Tray Cover.

3 Remove the shipping tape and foam from inside the Tray cavity.

4 If you are loading Letter or A4 size paper, pull the Tray Extension out to the first stop.

5 If you are loading Legal size paper, lift the Tray Extension slightly and pull it out to the second stop.

6 Place a piece of paper in the tray and test to see the Side Guides are in the correct position for your paper.

Lanier 2002 — Setting Up Fax Unit diagram (page 178)
Fig. 53 · Setting Up Fax Unit

7 To change the positions of the Guides to a new size paper, snap them out and re-locate them.

8 Place paper in the Tray and push the Tray Extension in against the end of the paper.

9 Replace the Tray Cover.

A - 8 Unpacking & Installation

Page 179 of the Lanier 2002 user manual — Setting Up Fax Unit
Page 179 · click to enlarge
Page 179

Setting Up Fax Unit

Lanier 2002 — Setting Up Fax Unit diagram (page 179)
Fig. 54 · Setting Up Fax Unit

1 Turn the Main ON/OFF Switch to the ON position.

2 After the power is turned ON, the fax goes through an initialization cycle until it is Ready. If not used for a period of time, the fax unit goes into the Standby mode.

3 If a problem occurs during a transmission causing the lose of system data or memory, this unit generates a Power Fail Report and emits short intermittent beeps.

Unpacking & Installation A - 9

Page 180 of the Lanier 2002 user manual — Final Checkout
Page 180 · click to enlarge
Page 180

Final Checkout

Final Checkout

Preparing Your Fax Unit

Before using your facsimile unit, please set up the following items:

1. Current Date and Time Your Fax unit can print out a report with the transmission date and time for identifications. Refer to Program User Data: Set Date/Time.
2. User Fax Number You Fax unit can print out a transmission report at a remote unit with your fax number for identification.

Refer to Program User Data: Set User FAX Number.

3. User Name You Fax unit can print out a transmission report at a remote unit with your company name for identification. Refer to Program User Data: Set User Name.
4. Correct Dialling Type (Tone or Pulse)

Select either TONE or PULSE according to the type of telephone system connected to the facsimile unit. Refer to Machine Option: TONE/PULSE.

5. Fax Line Type (PSTN/ PBX)

If you Fax unit is connected to the public switch telephone network (PSTN), you can select “PSTN”, otherwise, select “PBX.” Refer to Machine Options: PSTN/PBX.

Note: With a PBX system, you generally have to dial a prefix number (e.g. “9”) to access an outside line. If you set the line type to “PBX”, you can set the prefix number in advance. Then the unit can dial the prefix number for you whenever you dial. The following table shows you how to dial when using the PBX mode. The prefix can be up to four (4) digits in length.

Phone LIne Telephone Number LCD Display/Dialing Access Line

PBX mode, prefix=9 123 @123 PBX

PBX mode, prefix=9 #123 9-123 PBX -> PSTN

A - 10 Unpacking & Installation

Page 181 of the Lanier 2002 user manual — Final Checkout
Page 181 · click to enlarge
Page 181

Final Checkout

Loading a Document

1 Place a document face down in the Document Feed Tray.

Lanier 2002 — Final Checkout diagram (page 181)
Fig. 55 · Final Checkout
  • Torn, wrinkled or curled paper
  • Coated paper
  • Thin or transparent paper
  • Film copies of document
  • Thicker than a postcard
  • Originals of cloth

2 Adjust the document Side Guides to fit your original.

Lanier 2002 — Final Checkout diagram (page 181)
Fig. 56 · Final Checkout

3 Enter the telephone number for another fax unit.

4 Press the Start Key.

5 Check to make sure the transmission was successful.

6 If the transmission was successful, you are now ready to do the remainder of the programming.

7 If the transmission was not successful, refer to the Troubleshooting Chapter or place a service call with your Service Representative.

Unpacking & Installation A - 11

Page 182 of the Lanier 2002 user manual — Unpacking the PFU
Page 182 · click to enlarge
Page 182

Setting Up the (Optional) PFU

Setting Up the (Optional) PFU

The PFU option allow you to add a 500-sheet Cassette. This allows you to make longer fax, copy or printing runs without interruptions. The PFU installs under the Fax unit and serves as a base for it. We recommend that you un-pack this unit first. After you complete this procedure, go back to the installation procedure for the Fax unit and install the Fax on top of the PFU.

Unpacking the PFU

Unpacking the accessory boxes and verify that the following items are included in the kit: 1. PFU Carton

2. Packing Material
Lanier 2002 — Unpacking the PFU diagram (page 182)
Fig. 57 · Unpacking the PFU
3. PFU Assembly
4. Packing Material
5. Paper Cassette
6. Packing Material

A - 12 Unpacking & Installation

Page 183 of the Lanier 2002 user manual — Setting Up the (Optional) PFU
Page 183 · click to enlarge
Page 183

Setting Up the (Optional) PFU

Installing the PFU

1 Take the (Optional) PFU from the shipping carton.

Lanier 2002 — Setting Up the (Optional) PFU diagram (page 183)
Fig. 58 · Setting Up the (Optional) PFU

2 Remove the vinyl bag and peel off the shipping tape.

3 Remove the shipping tape and cardboard from the gear area.

4 Remove any shipping material and tape from the Cassette cavity.

5 Place the Fax unit on top the PFU making sure the three Aligning Posts and the Power Connector are carefully aligned.

Lanier 2002 — Setting Up the (Optional) PFU diagram (page 183)
Fig. 59 · Setting Up the (Optional) PFU

Unpacking & Installation A - 13

Page 184 of the Lanier 2002 user manual — Setting Up the (Optional) PFU
Page 184 · click to enlarge
Page 184

Setting Up the (Optional) PFU

Loading the Cassette

1 Remove the Cassette from the vinyl bag.

2 Remove the shipping tape and cardboard.

3 Press down the Baseplate until it locks into position.

Lanier 2002 — Setting Up the (Optional) PFU diagram (page 184)
Fig. 60 · Setting Up the (Optional) PFU

4 Place a sheet of paper on the baseplate and check to see that the Cassette is set for that paper size.

5 To change the Cassette Paper size, remove the necessary screws and re- position the guides for the new size.

6 Fan the paper stack thoroughly and align its edges.

7 Load the paper into the Cassette.

A - 14 Unpacking & Installation

Page 185 of the Lanier 2002 user manual — Setting Up the (Optional) PFU
Page 185 · click to enlarge
Page 185

Setting Up the (Optional) PFU

8 Do not load paper above the Maximum Level Indicator.

Lanier 2002 — Setting Up the (Optional) PFU diagram (page 185)
Fig. 61 · Setting Up the (Optional) PFU

9 If you add paper prior to the tray being completely empty, make sure you place the old paper on top the stack.

10 Put the Cassette Cover on the Cassette.

Lanier 2002 — Setting Up the (Optional) PFU diagram (page 185)
Fig. 62 · Setting Up the (Optional) PFU

11 Install the Cassette into the PFU.

Unpacking & Installation A - 15

Page 186 of the Lanier 2002 user manual — Setting Up the (Optional) PFU
Page 186 · click to enlarge
Page 186

Setting Up the (Optional) PFU

Notes:

A - 16 Unpacking & Installation

Page 187 of the Lanier 2002 user manual — Appendix B
Page 187 · click to enlarge
Page 187

Appendix B

Safety & Agency

Certifications

Page 188 of the Lanier 2002 user manual — Safety & Agency Certifications
Page 188 · click to enlarge
Page 188

Safety & Agency Certifications

Page 189 of the Lanier 2002 user manual — CDRH Regulations
Page 189 · click to enlarge
Page 189

Energy Star

Energy Star

As an Energy Star Partner, LANIER has determined that this machine meets the Energy Star Guidelines for Energy Efficiency.

What is an Energy Star Machine?

Energy Star Machines have a feature that allows them to automatically turn off or go to sleep after a period of inactivity, ensuring night and weekend shut off.

Laser Safety

This FAX contains a page printer which operates by means of a laser. There is no possibility of danger from the laser, provided the FAX is operated according to the instructions in this manual provided. Since radiation emitted by the laser is completely confined within protective housing, the laser beam cannot escape from the machine during any phase of user operation.

Internal Laser Radiation (For all Users)

Maximum Radiation power7.3Þ10 -4 (W)Wave Length: 770-810 (nm)

This is a Class IIIb Laser Diode assembly that has an invisible laser beam. The printer head unit is NOT A FIELD SERVICE ITEM. Therefore, the printer head unit should not be opened under any circumstances.

For United States Users

Laser Safety

This FAX is certified as a Class 1 Laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Food, Drug and Cosmetic Act of 1990. This means that the FAX does not produce hazardous laser radiation.

CDRH Regulations

The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. Compliance is mandatory for products marketed in the United States. The label shown below indicates compliance with the CDRH regulations and must be attached to laser products marketed in

Safety & Agency Certifications B - 1

Page 190 of the Lanier 2002 user manual — FCC Safety Statement
Page 190 · click to enlarge
Page 190

Energy Star

the United States.

Use of controls, adjustments or performance of procedures other than

WARNING:

those specified in this manual may result in hazardous radiation

exposure.

For Users In Other Countries

This is a semiconductor laser. The maximum power of the laser diode is 5.0Þ10-4 W and the wavelength is 770-810 nm.

FCC Safety Statement

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designated to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that there will be no interference to radio or television reception. This can be determined by turning the equipment off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced Radio/TV technician for help.

THIS EQUIPMENT. YOU ARE CAUTIONED THAT CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID YOUR AUTHORITY TO OPERATE THE EQUIPMENT.

B - 2 Safety & Agency Certifications

Page 191 of the Lanier 2002 user manual — Telephone Company Procedures
Page 191 · click to enlarge
Page 191

FCC Requirements

FCC Requirements

Label Identification

The following information is applicable to the Model 1205, 1210 and 1260 MFD units installed in the United States of America. This equipment complies with part 68 of FCC rules. On the back panel of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, provide this information to your telephone company. The REN for these units is 0.7B. The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called. In most, but not all areas, the sum of the REN's of all devices connected to one line should not exceed five (5.0). To be certain of the number of devices you may connect to your line, as determined by the REN, you should contact your local telephone company to determine the maximum REN for your calling area.

Type Of Service

The Model 2001 and 2002s are designed for use on standard device telephone lines. Connection to coin service provided by the telephone company (central office implemented systems) is prohibited. Connection to party line service is subject to state tariffs.

Telephone Company Procedures

The goal of the telephone company is to provide you with the best service it can. To do this, it may occasionally be necessary for them to make changes in their equipment, operation, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice, in writing, to allow you to make the changes necessary to maintain uninterrupted service. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request. In certain circumstances, it may be necessary for the telephone company to request information from you concerning the equipment which you have connected to your telephone line. Upon request of the telephone company, provide the FCC registration number and the Ringer Equivalence Number (REN) of the equipment which is connected to your line. Both of these items are listed on the label on the back of the unit. The sum of all the REN's on your telephone lines should be less than five in order to assure proper service from the telephone company. In some cases, the sum of five may not be usable on a given line. The Telephone Customer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message, and the telephone number

Safety & Agency Certifications B - 3

Page 192 of the Lanier 2002 user manual — If A Problem Arises
Page 192 · click to enlarge
Page 192

FCC Requirements

of the sending machine or such business, other entity, or individual. To program this information into your machine, refer to the Programming section for information on entering your User ID and telephone number.

If A Problem Arises

If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of the disconnection. If advance notice is not feasible, you will be notified as soon as possible. When you are notified, you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC. In the event repairs are ever needed on your unit, it should be performed by a service technician authorized by the supplier from whom you purchased your unit.

B - 4 Safety & Agency Certifications

Page 193 of the Lanier 2002 user manual — Warning
Page 193 · click to enlarge
Page 193

FCC (For U.S.A. Users)

FCC (For U.S.A. Users)

FCC Part 15 - Radio Frequency Devices Warning

The following applies to the Facsimile Unit (LANIER 2001/2002) only without the LANIER Network option installed.

FCC : Declaration of Conformity Product Type Facsimile Product Name LANIER 2001/2002 Options Accessories Second Paper Cassette Unit Expansion Memory (Max 6MB) This Device complies with Part15 of the FCC Rules. Operation is subject to following Conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio-TV technician for help.
  • Any changes or modifications not expressly to operate this equipment. Note:
  • A LAN adapter (LANIER Network) is to be used only in industrial areas. Use of a LAN adapter in residential areas is not recommended.
  • This device must be used with shielded interface cables. The use of non-shielded cables is likely to result in Interference with radio communications and is prohibited under FCC rules.
  • The design and production of this unit conforms to FCC regulations, and any changes or modifications must be registered with the FCC and are subject to FCC control. Any changes made by the purchaser or user without first contacting the manufacturer will be subject to penalty under FCC regulations. FCC Part 15 - Radio Frequency Devices Warning

The Facsimile Unit (LANIER 2001/2002) with the LANIER Network option installed meets the FCC Class A requirements when the network cable is attached either of the IEEE 802.3 connectors.

Safety & Agency Certifications B - 5

Page 194 of the Lanier 2002 user manual — FCC Part 68 - Telecommunication Devices
Page 194 · click to enlarge
Page 194

FCC (For U.S.A. Users)

Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference at his own expense. This device must be used with shielded cables likely to result in interference with radio communications and is prohibited under the FCC rules. The design and production of this unit conform to FCC regulations, and any changes or modifications must be registered with the FCC and are subject to FCC control. Any changes made by the purchaser or user without first contacting the manufacturer will be subject to penalty under FCC regulations.

FCC Part 68 - Telecommunication Devices

This equipment complies with Part 68 of the FCC rules. On the rear panel of this equipment is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. If requested, provide this information to your telephone company.

This Equipment uses the Following USOC Jacks: RJ11C.

The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called. In most, but not all areas, the sum of the RENs of all devices should not exceed five (5.0). To be certain of the number of devices you may connect to your line, as determined by the REN, you should call your local telephone company to determine the maximum REN for your calling area.

If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice isn’t practical, you will be notified as soon as possible. You will be advised of your right to file a complaint with the FCC.

Your telephone company may make changes to its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. If they do, you will be given advance notice so as to give you an opportunity to maintain uninterrupted service.

B - 6 Safety & Agency Certifications

Page 195 of the Lanier 2002 user manual — Warning For Setting Headers and Footers
Page 195 · click to enlarge
Page 195

FCC (For U.S.A. Users)

If you experience trouble with this equipment, please contact:

The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning.

This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission or corporation commission for information.)

Customer Information for Privately Owned coin Phones

To comply with state tariffs, the telephone company must be given notification prior to connection. In some states, prior approval of connection must be obtained from the state Public Utility Commission, Public Service Commission or state Corporation Commission.

Warning For Setting Headers and Footers

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual.

In order to program this information into your fax machine, you should complete the following steps. (Refer to the Advance Operation Chapter for more information.

Safety & Agency Certifications B - 7

Page 196 of the Lanier 2002 user manual — Notice:
Page 196 · click to enlarge
Page 196

User Instructions (For Canada Users)

User Instructions (For Canada Users)

Interference-Causing Equipment Standard (ICES-003 ISSUE 2)

Warning:

The following applies to the Facsimile Unit (LANIER 2001/2002) only without the LANIER Network option installed.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.

Interference-Causing Equipment Standard (ICES-003 ISSUE 2)

Warning:

The following applies to the Facsimile Unit (LANIER 2001/2002) only with the LANIER Network option installed.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.

IC CS-03-Telecommunication Device

Notice:

Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. IC does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

B - 8 Safety & Agency Certifications

Page 197 of the Lanier 2002 user manual — Ozone Release (For all Users)
Page 197 · click to enlarge
Page 197

User Instructions (For Canada Users)

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution:

Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

Hearing Aid-Compatibility (For U.S.A / Canada Users)

This equipment complies with the FCC/IC guide lines for hearing aid-compatibility.

Agency Certifications

CE Mark

This equipment complies with the requirements of directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and the Harmonisation Directive 93/68/EEC.

Lanier Worldwide, Inc. Im Taubental 6 41468 Neuss 1 Germany

Ozone Release (For all Users)

During printer operation, a small quantity of ozone is released. This amount is not large enough to harm being adversely. However, be sure the room where the FAX is being used has adequate ventilation, especially if you are printing a high volume of materials, or if the FAX is being used continuously over a long period.

Safety & Agency Certifications B - 9

Page 198 of the Lanier 2002 user manual — Warning Labels
Page 198 · click to enlarge
Page 198

Warning Labels

Warning Labels

Lanier 2002 — Warning Labels diagram (page 198)
Fig. 63 · Warning Labels

B - 10 Safety & Agency Certifications

Page 199 of the Lanier 2002 user manual — Appendix C
Page 199 · click to enlarge
Page 199

Appendix C

Glossary

Page 200 of the Lanier 2002 user manual — Glossary
Page 200 · click to enlarge
Page 200

Glossary

Page 201 of the Lanier 2002 user manual — Glossary
Page 201 · click to enlarge
Page 201

Glossary

Glossary

ADF Automatic Document Feeder

Batch A group of documents stored in memory at different times and sent together at the same time to a remote unit.

Broadcast Transmit one document to more than one location, sequentially. This function is available only when Memory Transmit is selected.

Cancel Session Cancel a Delay Transmit or Poll Receive session from memory.

CRX Continuous Poll Receive - Appears in the Display when the unit is in the Continuous Poll Receive mode, continually polling a list of remote units.

Delay Transmission Allows you to delay sending a document to a single location.

Document Memory Electronic storage in your fax unit that can store documents for Memory Transmit, for Confidential or for Paper Receive.

ECM Error Correction Mode

Enable Turn a feature ON, or make adjustments necessary for a feature to perform.

Extremely Fine Extremely poor quality documents.

Facsimile A system of sending printed or graphic information from one location to another by producing a copy (or facsimile) for that information at the Transmitting Location, converting it to an electronic image and sending it over the same telephone lines you use for voice calling.

File Electronic data for one document stored in memory in the fax unit.

File Number A unique, 3-digit number automatically assigned by the fax unit to reach document stored in memory. This number is printed on reports regarding information on the particular file. It is also used to verify or clear the document from memory.

Fine Documents with fine lines and character.

Group Dial Sequentially dialling more than one location. A Program key in the 1210/1260 MFD can store multiple telephone numbers, enabling the user to enter multiple locations with one key stroke when using Memory Transmit. Group Dial can also be performed by entering multiple One Touch locations for a session.

ITT - TSS International Telecommunications Union - Telecommunications Standardization Sector (formerly CCITT)

LCD Liquid Crystal Display

Glossary Appendix C - 1

LN Load Number · MFD Multifunction Device

Page 202 of the Lanier 2002 user manual — Glossary
Page 202 · click to enlarge
Page 202

Glossary

One Touch key Can store selected job features and phone numbers using the program keys.

OT One Touch key

Photo Photographs and glossy photo-quality originals.

Poll One fax unit asking another unit if the called unit has documents loaded in the Feeder or stored in memory to send to the calling unit.

Receiving Converting the electronic signals into a facsimile of the original document.

Reduction Reducing incoming documents to fit to the size of the paper in your cassette.

Relay Broadcast To initiate a Relay Broadcast to a Relaying unit, which then sends the document to a group of receivers.

REN Ringer Equivalence Number

Scanning Reading and converting the document information into electronic signals.

Sender ID The letters and numbers you choose to enter into your fax unit to identify yourself or your company to a remote fax unit. Your Sender ID will print out at the top of copies you transmit to other fax units.

Session The activity performed by a fax unit from the time START is activated to the time the fax unit disconnects the telephone line and returns to Standby.

Sub-Addressing To send a document to a compatible computer system and have it delivered to an individual network user.

Transmitting Sending the signals through a telephone to another facsimile receiving device.

Appendix C - 2 Glossary

Show 7 more labels / short text on this page
ORG Original · RX Received Transmission · SD Speed Dial · SESS Session Number · STD Standard Mode · TEL Telephone · TX Outgoing Transmission
Page 203 of the Lanier 2002 user manual — Table of Contents
Page 203 · Contents
Contents

Contents

Trademark Acknowledgmentsp.2Introductionp.9Introduction to the 2001 and 2002 Unitsp.112001/2002 Model Differences*p.11How to Use This Manualp.11Agency Certificationp.11Important Safeguardsp.12Multi-Taskingp.14Machine Componentsp.15Control Panel Layoutp.18Definition of Display Symbolsp.22Basic Operationsp.23Sending a Documentp.25Using Memory Transmitp.25Memory Overflow Transmitp.26Direct (Non-Memory) Transmitp.27Using Handsetp.28Using the HOOK Keyp.29Using Combination Dialp.30Dialing Methodsp.31Receiving a Documentp.32Auto Receivep.32Manual Receivep.33Memory Receive (Memory Lock)p.34Substitute Memory Receivep.35Making Copiesp.36Advanced Facsimilep.39Using the Function Menup.41Broadcastp.42Timer TX (Delay Transmission)p.43Mailbox TXp.44Print Mailbox RXp.45Polling TXp.46Polling RXp.47Continuous Polling RXp.47Relay Initiatep.48Using Combination Dialp.49Using TEL DIRp.50JOURNAL Keyp.51REPORT Keyp.52Reportsp.53Transmit Message Confirmationp.53Manual TX Reportp.53SCHEDULE Keyp.54PIN CODE Keyp.552 SIDED TX. Keyp.56HOOK Keyp.57Facsimile Programmingp.59Accessing The User Program Areap.61Menu Navigationp.61Menu Structurep.62Entering Numbers and Lettersp.64Initial User Datap.65Entering The Date & Timep.65Entering Your Telephone Numberp.65Entering Your User Namep.66Setting Department PWp.66Machine Operationsp.67Setting Your Fax Line Type (PSTN/PBX)p.67Setting the Buzzer (Ring) Volumep.68Setting the Line Monitor (Speaker) Volumep.68Setting the Power Save Modep.69Selecting Remote Monitorp.69Selecting Remote Programp.70Setting the Correct Dialing Type (Tone/Pulse)p.70Document Scan Settingsp.72Resolutionp.72Scan Contrastp.73Print Densityp.73Reduction Copyp.74Rec. Paper Sizep.75Auto Cassette Sel.p.75Dial Registrationp.76One-Touch Keysp.76Speed Dial Keysp.77Group Dial Keysp.78Program Dialp.79Batch TXp.81TX Operationp.83Default TXp.83Closed Network TXp.84Fax Forwardingp.84Headerp.86RX Operationp.87Memory RX Modep.87No. of Ringsp.89Two Page Printp.89Reduction RXp.90Mailbox RXp.90Closed Networkp.91RX Modep.91Footer (Receive Time Print)p.92Continuous Poll RXp.93Line 2 Settingp.95Line 2 Fax No.p.95TX Line Priorityp.95Line 2 Tone / Pulsep.96Reportsp.97Activity Reportp.97Reserv. (Reservation) Reportp.97TX Results Reportp.98RX Results Reportp.98Broadcast Reportp.99Toner Low Reportp.99Other Reports and Listsp.100Setting the Department Number and Password (PW)p.101Assigning a Private Mailbox ID and Password (PW)p.103Editing the RX in Memory Password (PW)p.105PC Printing & Scanningp.107Set Printer (2002 Only)p.109Number of Copiesp.110Symbol Setp.110Font Numberp.111Line Numberp.113Print Fontp.113PCL4p.114GDI Enhancep.115Memory Allocationsp.116Standard Memory Configuration Choicesp.116PCL4 Emulation (2002 only)p.117Connecting to a Computerp.117Setting Up the Computer Application Printer Driverp.118Basic Operationp.118Using the Manual Feed Tray to Printp.118Printing Envelopesp.118Printer Messagesp.119Auto-Select Paper Trayp.119GDI Printer Featurep.120PC Requirementsp.120Connecting to Your PCp.121Installing The Printer Driverp.121Configuring the GDI Print Settingsp.125Printing with your GDI Print Functionp.125Getting Helpp.125Scanning (TWAIN Driver Option)p.126PC Requirements for the TWAIN Optionp.126Installing the TWAIN Driverp.126Scanningp.127Scanner Troubleshootingp.129Class 1 Fax/Modemp.130Class 1 Interfacep.130PC Requirementsp.130Connecting Class 1 to Your PCp.131Installing the PC-Fax Softwarep.131Using Class 1 Modep.131Sending a Fax in Class 1 Modep.132Receiving a Fax in Class 1 Modep.132Scanning in Class 1 Modep.132Printing in Class 1 Modep.133Maintenance & Suppliesp.135Loading the Paperp.137Paper Trayp.137Optional PFU Paper Cassettep.138Clearing Paper Jamsp.140Document Jamsp.140Paper Jamsp.141Changing Toner Cartridgep.145Changing Drum Cartridgep.146Maintenancep.148Cleaning Your Fax Unitp.148Cleaning the Scannerp.148Cleaning the White Rollerp.149Troubleshootingp.151Troubleshootingp.153Error Indication Typesp.153Error Messagesp.154Troubleshooting Tipsp.157Specificationsp.159Physical Specificationsp.161Electrical Specificationsp.161Operational Specificationsp.162Facsimile Specificationsp.164Optional Accessories Specificationsp.164Class 1 Interface (RS-232)p.164PC Interfacep.165LAN Interface (Print Server)(2002 Only)p.165Dual Linep.166Environmental Specificationsp.167Lithium Battery Statementp.167Unpacking & Installationp.169Unpackingp.171Main Carton Contentsp.171Accessories Box Contentsp.172Setting Up Fax Unitp.173Removing the Packing Materialsp.173Installing the Drum Cartridgep.173Installing the Toner Cartridgep.174Installing the Paper Exit Trayp.175Installing the Document Exit Trayp.175Installing the Document Feed Trayp.175Attaching the Power Cord and Telephone Cordsp.176Attaching the PC Cablesp.176Installing the Handsetp.177Loading Paperp.178Turning Power ONp.179Final Checkoutp.180Preparing Your Fax Unitp.180Loading a Documentp.181Setting Up the (Optional) PFUp.182Unpacking the PFUp.182Installing the PFUp.183Loading the Cassettep.184Safety & Agency Certificationsp.187Energy Starp.189Laser Safetyp.189Internal Laser Radiation (For all Users)p.189For United States Usersp.189For Users In Other Countriesp.190FCC Safety Statementp.190FCC Requirementsp.191Label Identificationp.191Type Of Servicep.191Telephone Company Proceduresp.191If A Problem Arisesp.192FCC (For U.S.A. Users)p.193Warning For Setting Headers and Footersp.195User Instructions (For Canada Users)p.196Interference-Causing Equipment Standard (ICES-003 ISSUE 2)p.196Interference-Causing Equipment Standard (ICES-003 ISSUE 2)p.196IC CS-03-Telecommunication Devicep.196Hearing Aid-Compatibility (For U.S.A / Canada Users)p.197Agency Certificationsp.197CE Markp.197Ozone Release (For all Users)p.197Warning Labelsp.198Glossaryp.199Glossaryp.201Indexp.203
Page 204 of the Lanier 2002 user manual — Index
Page 204 · click to enlarge
Page 204
Page 204 of the Lanier 2002 user manual — Index
Page 205 of the Lanier 2002 user manual — E
Page 205 · click to enlarge
Page 205

Telephone Handset 1-6 Telephone Line 1-6 Continuous Polling RX 3-7 Controls

F

Fax Transmit 2-1 FCC Requirements B-3 Function Menu 3-1

Symbols

’#’ Key 1-11 ’*’ Key 1-10 ’+’ Key 1-10 10-Key Pad 1-11 2-Sided TX 1-9 Arrow Keys 1-9 Auto RX Key 1-8 Copy Key 1-11 Function Key 1-9 Hook Key 1-10 Journal Key 1-9 Memory TX Key 1-8 NO Key 1-9 One-Touch Keys 1-10 Original Type Key 1-8 PIN Key 1-9 Program Key 1-9 Redial/Pause Key 1-10 Report Key 1-9 Resolution Key 1-8 Schedule Key 1-9 Speed Dial Key 1-10 START Key 1-11 STOP Key 1-11 TEL DIR Key 1-10 YES Key 1-9 Copying 2-12

“#” Key 2-7

G

Numerics

Configuring 5-14 Connecting to Your PC 5-11 Getting Help 5-14 Installing The Printer Driver . 5-11 PC Requirements 5-10 Printing 5-14 GDI Printer Feature 5-10 Group Dial 2-7

2 SIDED TX. Key 3-16

A

Agency Certification 1-1 Agency Certifications B-9 Auto Receive 2-8

H

B

HOOK Key 3-17

Broadcast 3-2

Changing Drum Cartridge 6-10 Changing Toner Cartridge 6-9 Class 1 Fax/Modem 5-18

Alarm 1-8 Auto RX 1-8 Memory TX 1-8 Initial User Data 4-5

D

Installing the PC-Fax Software 5-19 Interface 5-18 PC Requirements 5-18 Printing 5-21 Receiving a Fax 5-20 Scanning 5-20 Sending a Fax 5-20 Using Class 1 Mode 5-19 Clearing Paper Jams 6-4

Dial Registration 4-16

Batch TX 4-22 Group Dial Keys 4-18 One-Touch Keys 4-16 Program Dial 4-19 Speed Dial Keys 4-17 Dialing Methods 2-7 Direct (Non-Memory) Tansmit . . . 2-3 Display LCD 1-8 Document Scan Settings 4-12

Entering The Date & Time 4-5 Entering Your Telephone Number .

4-5 Entering Your User Name 4-6 Setting Department ID 4-6 Installing

Document Exit Tray A-5 Document Feed Tray A-5 Drum Cartridge A-3 Final Checkout A-10 Handset A-7 Paper Exit Tray A-5 PC Cables A-7 Power Cord A-6 Telephone Cords A-6 Toner Cartridge A-4

Document Feeder 6-4 Main Unit 6-5 Connector

Dual Line 1-6 External Line 1-6 Network 1-6 Parallel 1-6 RS232 1-6 Serial 1-6

E

Energy Star B-1 Entering Numbers and Letters 4-4

Index IX - 1

GDI Printer

Page 206 of the Lanier 2002 user manual — P
Page 206 · click to enlarge
Page 206

J

Selecting Remote Monitor . . . 4-10 Selecting Remote Program . . . 4-10 Setting the Buzzer (Ring) Volume .

Printer Messages 5-9

Auto-Select Paper Tray 5-9 Program Dial 2-7

JOURNAL Key 3-11

4-8 Setting the Correct Dialing Type

Broadcast 4-19 Mailbox TX 4-20 Polling RX 4-21 Relay Initiate 4-21 Timer TX 4-20

(Tone/Pulse) 4-11 Setting the Line Monitor (Speaker)

K

Volume 4-8 Setting the Power Save Mode . . 4-9 Setting Your Fax Line Type (PSTN/

Key Pad Dial 2-7

PBX) 4-7 Mailbox TX 3-4 Maintenance 6-12 Manual Receive 2-9 Memory Allocations 5-6

R

Receiving a Document 2-8 Relay Initiate 3-8 REPORT Key 3-12 Reports 3-13, 4-37

Laser Safety B-1 Line 2 Setting 4-35

Std. Memory Configuration . . . 5-6 Memory Overflow Transmit 2-2 Memory Receive (Memory Lock) 2-10 Memory Transmit 2-1 Menu Navigation 4-1 Menu Structure 4-2 Model, differences 1-1 Multi-Tasking 1-4

Line 2 Fax Number 4-35 Line 2 Tone / Pulse 4-36 TX Line Priority 4-36 Loading Paper 6-1

Activity Report 4-37 Broadcast Report 4-39 Manual TX Report 3-13 Other 4-40 Reservation Report 4-37 RX Results Report 4-38 Toner Low Report 4-39 Transmit Confirmation 3-13 TX Results Report 4-38 RX Operation 4-27

Optional PFU Cassette 6-2 Paper Tray 6-1

concurrent operations 1-4

M

O

Closed Network 4-30 Continuous Poll RX 4-33 Footer 4-32 Mailbox RX 4-30 Memory RX Mode 4-27 Number of Rings 4-29 Reduction RX 4-30 RX Mode 4-32 Two Page Print 4-29

Machine Components 1-5

AC Power Connector 1-6 Bypass Feed Tray 1-5 Control Panel 1-5 Control Panel Layout 1-8 Cover Release Buttons 1-7 Display Symbols 1-12 Document Alignment Guides . . 1-5 Document Exit Tray 1-5 Document Feed Tray 1-5 Drum Cartridge 1-7 Dual Line Connector 1-6 Hand Set Connector 1-6 Network Connector 1-6 ON/OFF Switch 1-6 Paper Exit Tray 1-5 Paper Feed Unit (PFU) 1-7 Paper Tray 1-5 Parallel Connector 1-6 Scanner Cover 1-5 Serial Connector 1-6 Telephone Line Connector 1-6 Toner Cartridge 1-7 Top Cover 1-7 Machine Operations 4-7

One Touch Dial 2-7 Options

Dual Line Connector 1-6 NIC Card 1-6 Paper Feed Unit (PFU) 1-7 Ozone Release B-9

P

S

Basic Operation 5-8 Connecting to a Computer 5-7 Printing Envelopes 5-8 Setting Up the Computer Application

Auto Cassette Select 4-15 Contrast 4-13 Installing the TWAIN Driver . 5-15 PC Requirements for the TWAIN

Printer Driver 5-8 Using the Manual Feed Tray to Print

Option 5-15 Print Density 4-13 Recording Paper Size 4-14 Reduction Copy 4-14 Resolution 4-12 Scanner Troubleshooting 5-17 Scanning 5-16

5-8 PCL4 Emulation (2002 only) 5-7 PIN CODE Key 3-15 Polling RX 3-7 Polling TX 3-6 Print Mailbox RX 3-5

IX - 2 Index

PCL4 Emulation · Scanning

Page 207 of the Lanier 2002 user manual — U
Page 207 · click to enlarge
Page 207

Scanning (TWAIN Driver Option) 5-15 SCHEDULE Key 3-14 Set Printer 5-1

Using Combination Dial . 2-6, 2-7, 3-9 Using Handset 2-4 Using TEL DIR 3-10 Using the HOOK Key 2-5 Using the TEL/DIR Key 2-7

Font Number 5-3 GDI Enhance 5-5 Line Number 5-4 Number of Copies 5-2 PCL4 5-5 Print Font 5-4 Symbol Set 5-2 Setting Up Fax Unit A-3 Setting Up the (Optional) PFU . . A-12 Specifications

W

Electrical 8-1 Environmental 8-7 Facsimile 8-4 Operational 8-2 Optional Accessories 8-4

Class 1 Interface (RS-232) . 8-4 Dual Line 8-6 LAN Interface 8-5 PC Interface 8-5 Physical 8-1 Speed Dial 2-7 Substitute Memory Receive 2-11 Supplies

Drum Cartridge 1-7 Toner Cartridge 1-7 Switch

ON/OFF 1-6

T

Timer TX (Delay Transmission) . . 3-3 Troubleshooting 7-1

Error Indication Types 7-1 Error Messages 7-2 Tips 7-5 Turning Power ON A-9 TX Operation 4-23

Closed Network TX 4-24 Default TX 4-23 Fax Forwarding 4-24 Header 4-26

U

Unpacking A-1 User Program Area 4-1

Index IX - 3

Page 208 of the Lanier 2002 user manual — Index
Page 208 · click to enlarge
Page 208

IX - 4 Index

Page 209 of the Lanier 2002 user manual — Limitation of Liability
Page 209 · click to enlarge
Page 209

New Machine Warranty and Limitation of Liability

Warranty — 90 days

Lanier warrants that its equipment and accessories will be free from defective parts and workmanship for a period of ninety (90) days from the date of first installation by Lanier’s Authorized Dealer. Customers must notify a Lanier servicing dealer or Lanier of a warranty claim within the warranty period. For a listing of authorized Lanier servicing dealers or to notify Lanier of a warranty claim, write to Lanier Worldwide, Inc., 2300 Parklake Drive, N.E., Atlanta, Georgia 30345-2979.

Warranty Exclusions

THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT WARRANTIES, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS AND THOSE ARISING FROM A COURSE OF DEALING OF USAGE OF TRADE. The Express Warranty will not apply to drums, cleaning blades, fuser cleaning felts, toner, developer or paper or to defects of damage incurred in transportation, or due to accident; neglect; misuse such as use of harmful or unapproved supplies; alterations; operator error; power surges; failure to properly install, clean, maintain, or repair; improper operating environment; or failure to provide proper utilities. The Express Warranty also will not apply to used or refurbished Lanier equipment unless Lanier expressly authorizes resale with its original equipment warranty.

Limitation of Liability

Fulfillment of Lanier’s warranty obligation shall be the Customer’s exclusive remedy and Lanier’s and the Lanier Dealer’s limit of liability for any breach of warranty or otherwise. In no event will Lanier or Lanier’s Dealers be responsible or liable for special, incidental or consequential losses or damages.

Page 210 of the Lanier 2002 user manual — U1201-4932
Page 210 · click to enlarge
Page 210

our commitment to your

www.lanier.com

next level document solutions

Lanier Worldwide, Inc. | 2300 Parklake Drive, N.E. | Atlanta, GA USA 30345

U1201-4932

Customer Vision _ · complete satisfaction

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
• The fax unit on the receiving side is not equipped with the mailbox function.• Cancel mailbox TX and retry transmission. p.154
• The paper feeding tray or second paper feeding tray has run out of paper.• Add Paper. p.154
• Toner Cartridge is not installed properly or Cartridge is missing.• Re-install Toner Cartridge properly or install a new Toner Cartridge. p.154
• (Machine trouble) A fault has occurred in the machine.• Call your Service Representative. p.154
• While the fax was receiving a document during mailbox RX, memory RX or Substitute RX the memory became full and facsimile machine is unable to store additional documents into memory.• Press the STOP Key and print any documents stored in memory. When memory is available, request the other party to retry the transmission. p.154
• While your fax was scanning a document for Memory TX, the Memory became full and the fax was unable to send the entire document using Memory TX.• To transmit the portion of the document that has been scanned into memory, press the START Key. To increase the memory capacity of the fax machine, print out any documents that were received into memory or wait until other memory transmission jobs are completed. Then retry your Memory TX. • To cancel what has been scanned into memory, press the YES key. To increase the memory capacity of the fax machine, print out any documents that were received into memory or wait until any other memory transmission jobs are completed. Then retry your Memory TX. p.154
• A document jam has occurred.• Clear the misfeed or jam by following the procedures given in “Clearing Document Jams.” p.154
• The fax machine Cover is open or loose.• Lock the fax machine Cover in position. p.154
• A recording paper jam has occurred.• Clear the jam by following the procedure given in “Clearing Paper Jams.” p.155
• The Scanner Cover (Control Panel) is open or loose.• Close the Scanner Cover. p.155
• The fax is almost out of Toner.• Replace the Toner Cartridge with a new one. If you leave it without replacing, printed image might be light. p.155
• The fax unit has run out of toner.• Change the Toner Cartridge. p.155
• An error has occurred and communication was unsuccessful.• At transmission: Press the STOP Key, then try another transmission sequence. • At reception: Press the STOP Key then ask the other party to try another transmission. p.155
• There is no destination information programmed in the One-Touch Key or Speed Dial number you have just pressed.• Select the One-Touch Key or Speed Dial number which contains the information of the destination you are trying to send. p.155
• The document has not been transmitted to the other party even through repeated auto re-dial attempts.• Press the STOP Key, check the fax number, then try another transmission sequence. p.155
• The Mailbox ID entered has been previously assigned.• Enter a new Mailbox ID. p.155
• The Mailbox ID specified by the other party does not match the Mailbox ID programmed in your fax.• Advise the other party of the correct Mailbox ID and ask them to retry the transmission or ask the party to cancel Mailbox TX and retry transmission. p.155
• The number of pages of the document transmitted does not equal the number of pages set with page count TX.• Check the number of pages again and retry the transmission. p.155
• After several attempts, transmission is unsuccessful.• Check to make sure telephone line is properly connected to the fax machine and the wall jack. p.155
• Remote machine not compatible with your machine.• Check the other party fax machine. p.155
1 Nothing is shown on the Display.• make sure the Power Cord is plugged in properly. • Check the Main ON/OFF Switch to make sure it is in the ON position. • Check another electric appliance to the AC outlet to check whether the outlet is live. p.157
2 Nothing printed on the receiving side.• Make a local copy to check if your machine has amy problem. • Make sure the recording paper is properly loaded in the remote receiving unit. p.157
3 The machine fails to enter the reception mode when it is called.• Check whether the machine is in the automatic reception mode. • Check whether paper is empty or the memory is full. p.157
4 Automatic Document Feeder fails to work.• Check the document size. • Make sure the documents are properly placed in the Feeder. p.157
5 When the reception image has black stripes.• Use your fax to make a copy of the document. • If the copied document does not have black stripes, ask the transmitting side to check their machine. • If the copied document has black stripes, contact service personnel. p.157
6 No sound can be heard from the telephone set.• Check if the Telephone Cord is correctly connected to the terminal of the fax. • Check if the Line Cord is connected correctly. p.157
7 Communication error.• Most errors are caused by bad line connections, so please retry. • Test with another fax machine. If this problem still exists, please contact your service representative. p.157
8 The image received is not clear.• Make a copy of another original with a clear image to check the image quality. • If the copy is clear: the telephone line or the fax machine of the other party is probably at fault. Ask the other party to re-transmit the document. p.157
9 The image is slanted on the page when you make a copy or receive a document.• Re-adjust the Guide in the Paper Cassette. p.157
10The copy quality is poor.• If any black lines appears on the page, please clean the surface of the scanning head under the Control Panel. If the image become faint or blurry, please remove the toner set and rock it. p.157
11The pages come out wrinkled or there are frequent paper jams or double feeding.• Check if the paper size and type fit your fax. • Check if the paper you are using is rippled or creased. p.157

Ask about the Lanier 2002

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lanier 2002

Be the first to ask — other owners or our team will answer.

Original document

Lanier 2002 manual PDF

210 pages·3 MB·Fax Machine·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…