Instruction/ maintenance manual of the product KHMF 9010/I KitchenAid
Go to page of 20
KHMF 9010/I Instructions for use 5019_719_01120_GB_STEP_FILO:Layout 1 19-07-2007 14:03 Pagina 1.
5019_719_01120_GB_STEP_FILO:Layout 1 19-07-2007 14:03 Pagina 2.
Product description and symbols 4 Gas burner functions 4 Practical advice on how to use the burners 5 Injectors table 5 Induction zone functions 6 Positioning the pan supports and Wok support 7 Sizes .
1. Removable pan supports 2. Professional double crown W ok burners 3. 145 mm diameter induction zone 4. Left gas burner control knob 5. Central gas burner control knob 6. Right gas burner control knob 7. Display and touch control panel for the induction zones Gas burner control knob symbols A.
Read these instructions to get the best out of your burners: - Use pans with a diameter the same as the burner (see pan diameter table to the side). - Only use flat bottom pots and pans. - Use the right amount of water for cooking food and use the lid.
This hob is fitted with 2 induction zones that allow you to boil water very quickly , as well as control the temperature with extreme precision, giving you a vast range of cooking options. The induction zone control panel has the following functions. 1.
The time remaining can also be changed by pressing the clock symbol button (4) at any time and using the +/- buttons (3) to alter the time. The light above the display will flash for 10 seconds, then the display will show the amended time remaining. When the programmed time expires a continuous double signal will be heard.
NOTE: If a hood is installed above the hob, read the instructions for fitting the hood where it indicates the correct distances to be complied with. • The cooktop has to be set into a work top between 20 - 40 mm deep.
T o get the best out of your hob, please read the instructions carefully and keep them for future consultation. • These instructions are only valid in the countries whose symbol of destination is shown on the product description sheet and hob. • The packaging (plastic bags, expanding polyurethane, etc.
P acking The packaging material is 100% recyclable and is labelled with the recycling symbol that identifies it as a kind of material to be sent to local waste disposal centres. Product This appliance is marked according to the European Directive 2002/96/EC, W aste Electrical and Electronic Equipment (WEEE).
T echnical information for the installer • This product can be built into a 20 to 40 mm deep worktop. • The hob cannot be installed with an oven underneath. Always insert a separator panel under the hob at a distance of no less than 25 mm from the lowest point (electronic control module) on the appliance.
The gas mains system must comply with local regulations. • The paragraph on “national legislation reference” shows the local legislation specific to the country of destination. • Should there be no information regarding your country of interest, ask for further details from the installer .
1. After cleaning the surfaces around the edges, fit the seal provided around the hob. 2. P osition the hob inside the opening according to the sizes indicated in the description sheet. 3. Use the brackets (A) provided to secure the hob, fixing it with the proper screws to adapt it to the thickness.
(See the product description sheet for model) Remove the bottom of the hob, lifting out the installation brackets to change the dual crown wok burner injector . Please contact the Customer Care Centre. REMOVING THE MAIN INJECTOR Remove the injector (F) using a 10mm spanner .
In order to keep your hob in good condition, you must keep it clean, removing any food residue each time you use it. Always disconnect the hob from the electrical power supply and wait until it cools before cleaning.
The hob is not working properly or not working at all. Before calling the Customer Care Centre, see if the problem you are encountering is mentioned in this guide. Contact the Customer Care Centre to replace the power cable. Burners and gas rings 1. The burner doesn’t come on or the flame is uneven.
Before contacting the Customer Care Centre, clarify that you cannot resolve the problem yourself based on the descriptions given in the “T roubleshooting guide”. 1. T urn the apparatus off and restart it to see if the fault is repeated. If after carrying out the above checks, the fault persists, contact your Customer Care Centre.
5019_719_01120_GB_STEP_FILO:Layout 1 19-07-2007 14:04 Pagina 18.
5019_719_01120_GB_STEP_FILO:Layout 1 19-07-2007 14:04 Pagina 19.
5019 719 01120 Printed in Italy n 07/07 GB Whirlpool Europe S.r .l. Viale G. Borghi, 27 - 21025 Comerio (V A) Phone 0332.759111 - Fax 0332.759268 www .
An important point after buying a device KitchenAid KHMF 9010/I (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought KitchenAid KHMF 9010/I yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data KitchenAid KHMF 9010/I - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, KitchenAid KHMF 9010/I you will learn all the available features of the product, as well as information on its operation. The information that you get KitchenAid KHMF 9010/I will certainly help you make a decision on the purchase.
If you already are a holder of KitchenAid KHMF 9010/I, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime KitchenAid KHMF 9010/I.
However, one of the most important roles played by the user manual is to help in solving problems with KitchenAid KHMF 9010/I. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device KitchenAid KHMF 9010/I along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
