Instruction/ maintenance manual of the product DDX7019 Kenwood
Go to page of 10
© B54-4522-00/00 (KV/RV) MONIT OR WITH D VD RECEIVER DDX7019 DDX7039 INST ALLA TION MANU AL DDX7019_B54-4522-00_3.indd 1 DDX7019_B54-4522-00_3.indd 1 06.
2 | DDX7019/DD X7039 1 ..........1 2 ..........1 3 ..........2 4 ..........1 5 ..........1 6 ..........6 7 ..........6 8 ..........1 Ac cessories DDX7019_B54-4522-00_3.
English | 3 Installation Pr ocedure 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4.
4 | DDX7019/DD X7039 Connection B C PRK SW – + B C A A If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (gr ound), you may cause a short circuit, that in turn may star t a fire. Always connect those wires to the power source running through the fuse box.
English | 5 + + + + FRONT L FRONT R REAR L REAR R ANT. CONT P CONT EXT.CONT REVERSE ILLUMI MUTE REMO.CONT T o front left speaker T o front right speaker T o rear left speaker T o rear right speaker Wh.
6 | DDX7019/DD X7039 Sy stem Connection CAMERA REAR VIEW AV I N AV O U T FRONT REAR WOOFER SUB AV O U T A UDIO IN iP od VIDEO IN iP od ■ Front Preout • Audio left output ( White) • Audio right o.
English | 7 Optional Ac cessory Connection TV ANTENNA INPUT TO MONITOR UNIT A UDIO IN iP od VIDEO IN iP od Rear view KCA-iP300V (Optional Ac cessory) iPod (commercially av ailable) Disc Changer etc.
8 | DDX7019/DD X7039 Installing the Escutcheon For Gener al Motors 1. Refer to the section <Removing the Hard Rubber Frame> and then r emove the hard rubber frame. 2. Cut out accessory 4 to meet the shape of the opening of the center console. 3.
English | 9 Installation for Monitor/Pla yer Unit Accessory 2 Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercially available) Screw (M4X8) (commercially available) Make sure that the unit is installed securely in place.
10 | DDX7019/DD X7039 Removing Monitor/Pla yer Unit Removing the Hard Rubber F rame (escutcheon) 1. Engage the catch pins on the removal tool 3 and remove the two locks on the lower level . Lower the frame and pull it f or ward as shown in the figure.
An important point after buying a device Kenwood DDX7019 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenwood DDX7019 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenwood DDX7019 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenwood DDX7019 you will learn all the available features of the product, as well as information on its operation. The information that you get Kenwood DDX7019 will certainly help you make a decision on the purchase.
If you already are a holder of Kenwood DDX7019, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenwood DDX7019.
However, one of the most important roles played by the user manual is to help in solving problems with Kenwood DDX7019. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenwood DDX7019 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
