Instruction/ maintenance manual of the product 9757 Kenmore
Go to page of 48
® Gas Dryer Secadora a Gas Models/Modelos 110.9756", 9757", 9758"_ = color number/n0mero de color W10035060 Sears Roebuck and Co., Hoffman Estates, IL 60179 U.
TABLE OF CONTENTS WARRANTY ..................................................................................... 2 DRYER SAFETY .............................................................................. 3 INSTALLATION INSTRUCTIONS ................
PRODUCT RECORD In the space below, record your complete model number, serial number, and purchase date. You can find this information on the model and serial number label located on the product. Have this information available to help you obtain assistance or service more quickly whenever you contact Sears concerning your appliance.
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions, including the following: [] Read all instructions before using the dryer. [] Do not place items exposed to cooking oils in your dryer.
INSTALLATION INSTRUCTIONS Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here, 8" or 10" pipe wrench 8" or 10" adjustable wrench (for gas connections) Flat-blade screwdriver Adjustable wrench that opens to 1" (2.
Alevel floor with a maximum slope of1"(2.5 cm) under entire dryer. (If slope is greater than 1"[2.5 cm], install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level.
Mobile home - additional installation requirements Installation spacing for cabinet installation This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home [] The dimensions shown are for the recommended spacing.
Explosion Hazard Use a new CSA International approved gas supply line. Install a shut=off valve. Securely tighten all gas connections. if connected to LP, have a qualified person make sure gas pressure does not exceed 13" (33 cm) water column.
Dryer gas pipe • The gas pipe that comes out through the rear of your dryer has a %" male pipe thread. B (15.9 cm) A. Y2" NPT gas supply line B. %" NPT dryer pipe *NOTE: If the dryer is mounted on a pedestal, the gas pipe height must be an additional 10" (25.
Clamps • Use clamps to seal all joints. • Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct. Do not use duct tape. Clamp Exhaust Recommended hood styles are shown here. _4 4 (1_-4"cm) (10.
Alternate installations for close clearances Choose your exhaust installation type Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer.
Determine vent length and elbows needed for best drying performance • Use the following Vent system chart to determine type of vent material and hood combinations acceptable to use. • NOTE: Do not use vent runs longer than those specified in the Vent system chart.
1= 2. 3= Remove the red cap from the gas pipe. Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound on the threads of all non- flared male fittings. If flexible metal tubing is used, be sure there are no kinks. A. Flared male fitting B.
5. Rotate outer door 180 °. 180 ° 6. Reassemble the inner and outer door assemblies with the 6 screws. Reverse hinge 1. Use a small flat-blade screwdriver to remove 2 plug strips from the inner door. Slide the head of the screwdriver under the plugs, being certain not to scratch the inner door surface.
1. Check that all parts are now installed. If there is an extra part, 7. go back through the steps to see which step was skipped. 8. 2. Check that you have all of your tools. 9. 3. Dispose of/recycle all packaging materials. 4. Check the dryer's final location.
DRYER USE STATUS AUTO Power CYCLES Delicate Wet _ 0 TIMED Damp _ Casual CYCLES Cool Down _ Timed Clothes Dry Ja_t _ More Dry Wrinkle Guard O _ Normal Jeans Express Dry 0 Less Controls Locked _ Touch U.
To use a Timed Cycle Select a Timed Cycle. Press MORE TIME or LESS TIME until the desired drying time is displayed. Tap MORE TIME or LESS TIME and the time will change by 1 -minute intervals. Press and hold MORE TIME or LESS TIME, and the time will change by 5-minute intervals.
Follow the progress of your dryer with the drying Status indicator lights. STATUS wet ? Damp ? Cool Down ? Clothes Dry 9 Wrinkle Guard O ControlsLocked Check Lint Screen Wet The Wet light illuminates at the beginning of an Auto Cycle if a wet item is detected.
Auto Cycles Preset Settings Auto Cycles Load Type Temperature Time* (Minutes) HEAVY DUTY High 45 Heavyweight mixed loads, towels JEANS Medium High 55 Denim pants, jackets NORMAL Medium 40 Sheets, cord.
You can customize your cycles by selecting options. O Wrinkle Guard 90 LOCK / bNLOCK CONIROLS WRINKLE GUARD e_ 90 WRINKLE GUARD ®90 helps smooth out wrinkles that form when you cannot unload the dryer promptly at the end of a cycle. During this option, the dryer periodically starts and stops, tumbling the load for 90 minutes.
This chart shows examples of items that can be rack dried and the suggested temperature setting and drying time. Actual drying time will depend on the amount of moisture items hold. Rack Dry Setting Temp. Time* Wool Sweaters Timed Low 60 Block to shape and lay flat on Cycles the rack.
To clean dryer drum 1. Make a paste with powdered laundry detergent and very warm water. 2. Apply paste to a soft cloth. OR Apply a liquid, nonflammable household cleaner to the stained area and rub with a soft cloth until all excess dye and stains are removed.
TROUBLESHOOTING First try the solutions suggested here and possibly avoid the cost of a service call... Dryer will not run • Has a household fuse blown, or circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.
Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Place dryer at least 18 inches (48 cm) above the floor for a garage installation.
JNDICE GARANTIA .................................................................................... 25 SEGURIDAD DE LA SECADORA ................................................ 26 INSTRUCCIONES DE INSTALACION .........................................
REGISTRO DEL PRODUCTO En el espacio a continuaci6n, anote el nt]mero complete de modelo y serie asi como la fecha de compra. Usted puede encontrar esta informaci6n en la etiqueta con el nOmero de modelo y de serie ubicada en el producto.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD ADVERTENClA: A fin de reducir el riesgo de incendio, descarga electrica o de daho alas personas que usen la secadora, deben seguirse las precauciones basicas, incluidas las siguientes: [] Lea todas las instrucciones antes de usar la secadora.
INSTRUCCIONES DE INSTALACION ReQna las herramientas y piezas necesarias antes de comenzar la instalaci6n. Lea y siga las instrucciones provistas con cualquiera de las herramientas enlistadas aqu(.
• Un contacto con conexi6n a tierra ubicado a no mas de 2 pies (61 cm) de cualquiera de los lades de la secadora. Vea "Requisitos electricos." • Un piso resistente para soportar la secadora con un peso total de 127 Ibs (57,6 kgs). Asimismo se debe considerar el peso de otro artefacto que la acompa_e.
Instalacibn empotrada o en el cl6set - Secadora sobre el pedestal (2,5 cm) eel 14f_ 27"---_- 4E-- 1" (68,6 cm) A I-1t I1"*1_ 28,65"_-I 5""1 {2,5cm) {2,5cm) (72,77cm) (12,7crn) B A.
Peligro de Choque Electrico Conecte a un contacto de pared de conexi6n a tierra de 3 terminales. No quite la terminal de conexi6n a tierra. No use un adaptador. No use un cable electrico de extensi6n. No seguir estas instrucciones puede ocasionar la muerte, incendio o choque el_ctrico.
Si los c6digos locales y el proovedor de gas Io permite, es aceptable una tuberfa de aluminio o cobre aprobada de %" para longitudes menores de 20 pies (6,1 m). Si usted esta usando gas natural, no use tuberfa de cobre. Un adaptador abocinado NPT de %" por %" entre el tubo de la secadora y la tuberfa aprobada de %".
Si este es un nuevo sistema de ventilacibn _J_YAYAYAYAY_ Material de ventilaci6n • Use un ducto de escape de metal pesado. No use ducto de escape de plastico o de hoja de metal. • Se debe usar un ducto de escape de metal pesado de 4" (10,2 cm) y abrazaderas.
S ,;::,%_t {¢:_ (}@ ............... Instalaciones alternas para espacios limitados Seleccione su tipo de instalacibn de ventilacibn Los sistemas de ventilaci6n vienen en una amplia gama.
Determinacibn de la via del ducto de escape • Seleccione la vfa que proporcione el trayecto mas recto y directo al exterior. • Planifique la instalaci6n a fin de usar el menor nQmero posible de codes y vueltas. • Cuando use los codos o haga vueltas, deje todo el espacio que sea posible.
Para su uso en casas rodantes Las secadoras a gas deben set aseguradas al piso en el momento de la instalaci6n. La instalaci6n en casas rodantes requiere el Juego de Instalaci6n para casas rodantes. Para obtener mas informaci6n, sirvase Ilamar al 1-800-4-MY-HOME ® (1-800-469-4663).
Usted puede invertir el cierre de la puerta de la apertura a la derecha a la apertura a la izquierda, si Io desea. 1. Coloque una toalla o un patio suave en la parte superior de la secadora o de la superficie de trabajo, para proteger la superficie. C6mo quitar el ensamblaje de la puerta 1.
Invierta el tope 1. Use un pequer_o destornillador de hoja plana para quitar la cinta del tapdn de la abertura de la puerta de la secadora. Deslice la cabeza del destornillador debajo de los tapones, siendo cuidadoso de no rayar la superficie de la secadora.
USO DE LA SECADORA STATUS AUTO Power CYCLES Delicate _ %, _t_,_T D !IMI RU_A#Vr Wet ? TIMED @-_' r_b" Damp?. Casual CYCLES O_ed_eie Cool Down Q Timed Wrinkle Guard O Normal Jeans Controls Lo.
5. 6. 7. NOTA: Las selecciones de Nivel de secado automatico (Dryness Level) funcionan Qnicamente con los ciclos de secado automatico. AI seleccionar Mas (More), Normal o Menos (Less) se regula automaticamente el tiempo detectado que se necesita.
Sugerencias de ciclos • Sequela mayorfa de las cargas usando los ajustes prefijados de ciclos. • Consulte el cuadro de Ajustes prefijados automaticos o programados (en la secci6n "Ciclos") a fin de obtener una guia para el secado de diversas cargas de ropa.
Ropa delicada (Delicate) Use este ciclo para obtener calor extra bajo para secar fibras sinteticas, tejidos de punto lavables y de acabado inarrugable.
Cuando use s61o aire • Revise las cubiertas para ver si las costuras estan firmes. • Sacuda y palmotee las almohadas con la mano peri6dicamente durante el ciclo. • Seque el art[culo completamente. Las almohadas de goma espuma tardan en secar. NOTA: El modificador de s61o aire no esta disponible en los ciclos de secado automatico.
NOTA: No permita que los arlculos cuelguen del borde del estante de secado. 4. Cierre la puerta. 5. Oprima el bot6n de suministro de energfa (POWER), 6.
Limpieza segt_n la necesidad Los residuos de detergente de lavandena y suavizante de telas pueden acumularse en el filtro de pelusa. Esta acumulaci6n puede ocasionar tiempos de secado mils prolongados para su ropa, o hacer que la secadora se detenga antes de que su carga este completamente seca.
&Hay una moneda, botbn o sujetapapeles entre el tambor y la parte frontal o trasera de la secadora? Revise los bordes frontales y traseros del tambor para verificar si hay objetos pequeSos. Limpie los bolsillos antes del lavado. Es una secadora a gas? El chasquido de la valvula de gas es un sonido de funcionamiento normal.
Pelusa en la ropa • &Esta obstruido el filtro de pelusa? Limpie el filtro de pelusa. Verifique si hay movimiento de aire. Manchas en la carga o en el tambor • &Se ha empleado adecuadamente el suavizante de telas? Agregue hojas de suavizante de telas al comienzo del ciclo.
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
An important point after buying a device Kenmore 9757 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenmore 9757 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenmore 9757 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenmore 9757 you will learn all the available features of the product, as well as information on its operation. The information that you get Kenmore 9757 will certainly help you make a decision on the purchase.
If you already are a holder of Kenmore 9757, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenmore 9757.
However, one of the most important roles played by the user manual is to help in solving problems with Kenmore 9757. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenmore 9757 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center