Instruction/ maintenance manual of the product 114.85925 Kenmore
Go to page of 17
Owner's Manual ® All Surface Floor Cleaner Model, Modelo 114.85925 CAUTION: Read and follow all safety and operating instructions before first use of this product, Sears, Roebuck and Co.
Before Using Your New All Surface Floor Cleaner .................. 2 Kenmore All Surface Floor Cleaner Warranty ...................... 2 Important Safety Instructions ....... 3-4 Parts and Features .................. 5 Assembly Instructions ..........
t _t I_s important to us, To VV/_I_I_I I I_1!_ reduce the risk of fire, electrical shock, injury to persons or damage when using your all surface floor cleaner, follow basic safety precautions including the following: Connect to a properly grounded outlet only.
Keep the All Surface Floor Cleaner on the floor. Do not use on stairs. Do not use an extension cord with this All Surface Floor Cleaner. Store the All Surface Floor Cleaner indoors. Put All Surface Floor Cleaner away after use to prevent tripping accidents.
It is important to know your All Surface Floor Cleaner's parts and features to assure its proper and safe use. Review these before using your All Surface Floor Cleaner.
Please pay special attention to these hazard alert boxes, and follow any instructions given. WARNING statements alert you to such dangers as fire, electric shock, burns and personal injury. CAUTION statements alert you to such dangerous personal injury and/or property damage.
OPERATING INSTRUCTIONS 1• Turn the quick reiease upper cord hook to either side and down to release the power cord. 2. Detach the power cord plug from the power cord and pull the cord off the quick release upper cord hook. 3. Plug the polarized power cord into a 120 Volt outlet located near the floor.
NOTE: Please read hard floor and carpet cleaning operating instructions prior to first use. For most effective cleaning, follow the recommended operating sequence below, IMPORTANT: For best cleaning results use a steady, forward and backward motion. Wet cleaning should be done at half the speed of dry vacuuming.
FILL Remove Tank-in- Tank" System from cleaner by pushing down on tank latch and tilting out. Remove measure cap from the rear of the Clean Water Tank. Pour 4 capfuls of Kenmore ® Hard Floor Concentrate Cleaner into Clean Water Tank. DO NOT USE PINE, SOLVENT I OR WAX BASED CLEANING SOLUTIONS IN CLEANER.
WASH AND DRY Step on Nozzle Setting pedal if necessary to switch from HARD FLOOR DRY VAC to WET SCRUB & VAC position. Slide Brush On/Off switch to the ON position. Pull Solution Trigger to start the flow of cleaning solution. NOTE; Cleaner will continuously dispense solution until Solution Trigger is released.
insert new nozzle by pushing securely into Nozzle Lock. NOTE: Make sure nozzle is inserted all the way in the Nozzle Lock, otherwise Nozzle Lock will not secure properly. Failure to install nozzle correctly can impact cleaning performance. NOZZLE LOCK TAB Turn Nozzle Lock Tab clockwise to lock nozzle onto cleaner.
Fill remainder of Clean Water Tank with warm water up to the MAX FILL line. Replace measure cap on Clean Water Tank. Replace Tank-in-Tank" System by inserting _ ottom first and tilting forward until tank latch fastens. WASH AND DRY With dry hands, plug cord Into properly grounded electrical outlet.
BRUSHROLL RESET BUTTON IMPORTANT: Your cleaner contains a reset button to protect the permanent belt should the brushroll clog. If this occurs, unplug the unit, remove debris from brushroll, and push reset button prior to resuming operation.
REPLACE TANK-IN-TANK" SYSTEM Return filter/float assembly to Dirty Water Tank. To ensure proper fit, make sure the arrow on the filter/float assembly lines up with the Align Filter Front arrow on Tank- in-Tank". Replace Tank-in-Tank TM System by inserting bottom first and tilting forward until tank latch fastens.
Replace filter by grasping angled top of filter and turning clockwise to lock onto fllter/fioat assembly. Return filter/float assembly to Dirty Water Tank. To ensure proper fit, make sure the arrow on the filter/ float assembly lines up with the Align Filter Front arrow on Tank- in-Tank TM.
Review this table to find do-it-yourself solutions for minor performance problems. Any service needed, other than maintenance described in this Owner's Manual, should be performed by a Sears or other qualified service agent. WARNING Disconnect electrical supply before performing maintenance to the unit.
Your Home Forrepair - in your home - of all majorbrand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
An important point after buying a device Kenmore 114.85925 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenmore 114.85925 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenmore 114.85925 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenmore 114.85925 you will learn all the available features of the product, as well as information on its operation. The information that you get Kenmore 114.85925 will certainly help you make a decision on the purchase.
If you already are a holder of Kenmore 114.85925, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenmore 114.85925.
However, one of the most important roles played by the user manual is to help in solving problems with Kenmore 114.85925. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenmore 114.85925 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
