Instruction/ maintenance manual of the product UFS 822sw Kathrein
Go to page of 156
Operating manual T win-PVR Satellite Receiver UFS 822sw/822si with hard disk and Ethernet.
2 PREF ACE Dear customer , this operating manual is intended to help you make the fullest use of the extensive range of functions offered by your new satellite receiver . We have tried to make the operating instructions as easy as possible to understand, and to keep them as concise as possible.
3 CONTENTS PREF ACE .............................................................................................................................. ... 2 CONTENTS .........................................................................................
4 IMPORT ANT INFORMA TION The channels available on the satellites and transponders are subject to continual change. In such cases, it is necessary to reset the channels as the factory preset programming corresponds to the situation on the date of manufacture.
5 REFERENCE NOTE ON AUDIO MPEG INC. AND S.I.SV .EL, S.P .A: This device employs legally protected technologies which are protected by patents in the USA as well as by intangible property laws in other countries. Audio MPEG Inc. and Societa‘ Italiana per lo sviluppo dell‘elettronica, S.
6 SAFETY INSTRUCTIONS - IMPORT ANT NOTES.
7 RECEIVER FEA TURES/SCOPE OF SUPPL Y The UFS 822 multi-functional satellite receiver is fi tted with two independent reception and signal processing systems as well as a computer hard disk with a ca.
8 CONTROLS, DISPLA YS AND CONNECTIONS This section provides a brief description of all the controls, displays and connections. The key symbols presented here can also be found in the description of the operating steps. Front panel controls and displays 1.
9 CONNECTION AND SET -UP The following section is intended speci fi cally for specialist dealers. Y ou only need read this section if you are performing the installation yourself. The “Connection Examples” section provides a sample con fi guration.
10 CONNECTION AND SET -UP T o enable you to utilise all the reception and recording properties of your UFS 822 twin-PVR Sat receiver , such as 1. recording one programme and at the same time viewing any other programme or zapping through the channels, and 2.
11 If only tuner 1 is connected (with no connection to tuner 2), the “Single Mode” setting must be selected for the tuner input. Y ou then have only the facilities of a normal “single receiver” available to you.
12 CONNECTION AND SET -UP Remove the cover on the rear of the remote control. Insert the two supplied batteries into the remote control. Ensure correct polarity of the batteries; the + and - markings are indicated inside the battery compartment. Slide the cover back into the housing until it locks in place.
13 REMOTE CONTROL Sound on/off ... Number input for channels, timers etc. Access main menu Exit menus (red) Access Favorites list ! (green) Picture-in-picture from 2 nd tuner or hard d.
14 REMOTE CONTROL REMOTE CONTROL RC 660 The RC 660 remote control supports up to four devices which are supplied with the RC 660 as standard. First, switch off all other receivers (mains switch). 1. Setting via menu (as of software version 1.01) For the UFS 822, the remote control code does not have to be entered manually .
15 FIRST INST ALLA TION First switch your TV set on and select the A V channel position. Switch on your receiver at the power switch on the rear of the unit. The following screen appears: Select the menu language you want using the buttons. Available options: German, English, Turkish, Italian, Spanish, Polish, Dutch and French.
16 Use the buttons here to select the settings for your TV set. Refer to the operating instructions for your television set! Video Output Here select the type of video signal at the Scart socket or HDMI socket. Select the signal that your TV set can process.
17 FIRST INST ALLA TION Note: If you are unsure whether you chose the right option from a previous menu, you can go back a step at any time during the First installation process by pressing the (red) button.
18 Press the buttons and the button to select the satellites from which you want tuners 1 and 2 to receive signals. Press the button to con fi rm your selection; the chosen satellite is then moved into the tuner satellite list on the right.
19 Select here the satellites you want tuner 2 to receive signals from, as you did for tuner 1. When you have selected all the satellites you want, press the ! (green) button. FIRST INST ALLA TION Press the buttons and the button to select the satellite con fi guration for each satellite you previously selected.
20 FIRST INST ALLA TION 22kHz Control: Press the buttons to make your selection (On/Off). The 22kHz Control is needed to switch LNBs in multi-feed reception and to switch between Low and High band. DiSEqC™ input: Press the buttons to make your selection.
21 T ransponder: Press the buttons to scroll through the transponders of the satellite highlighted in yellow at the top of the display . At the right you will see the signal strength of the transponder on the two tuners, enabling you to check that the satellite con fi guration you just set up is OK.
22 Single-cable system “Automatic” Single-cable system “Manual” Press the ! (green) button to continue with the installation. Display of the valid single-cable frequencies found by the receive.
23 Press the buttons and the button to select the satellites from which you want tuners 1 and 2 to receive signals. Press the button to con fi rm your selection; the chosen satellite is then moved into the tuner satellite list on the right.
24 Press the buttons and the button to select the satellites from which you want tuners 1 and 2 to receive signals. Press the button to con fi rm your selection; the chosen satellite is then moved into the tuner satellite list on the right.
25 - All: FT A (free-to-air) and encoded channels are searched for - Only FT A channels: Only non-encrypted channels, such as ZDF in Germany , are searched for - Only encrypted channels: Only encrypted channels, such as Austria's ORF , are searched for Perform the settings by pressing the buttons.
26 Press the button to con fi rm loading the newly found channels and move on to the next step in First installation. Here press the buttons to select the time mode: • Manual or • Auto.
27 Set Local Time Press the button to set the variance from UMTC (Universal Mean T ime Coordinate; formerly Greenwich Mean T ime) and Winter/ Summer time. At the bottom of the screen you see a listing of major cities to provide an indication of which time zone you have just set.
28 MENU TREE Main Menu (call up by pressing the button) Organize Channels Programme Guide System Setup Installation User Preference Recording List Multimedia/ Games Edit TV Channels TV Settings Fi.
29 OPERA TING INSTRUCTIONS The structure of the menu concept is based on logical operating sequences. The programme showing on the current selected channel always appears in the top right-hand corner of the screen.
30 OPERA TING INSTRUCTIONS The language for the on-screen display is set as follows: → → User Preferences → → Language Setup → → → German The languages available are German, English, Italian, French, Dutch, Polish, Spanish and T urkish.
31 ON-SCREEN DISPLA YS (OSD) The channel noti fi cation is displayed for a few seconds (con fi gurable on the “User Preference” menu under “Appearance Setup”) every time you change channel, or can be displayed permanently by pressing the button.
32 ON-SCREEN DISPLA YS (OSD) Press the button to access the channel list. At the top left a TV set or radio icon indicates whether the list is a TV channel list or a radio channel list. Press the # (blue) button to switch between the TV and radio channel lists.
33 Sort options (accessed by pressing the " (yellow) button): - Press the (red) button to access the alphabetical listing. It shows all the channels sorted alphabetically , or the ones beginning with the selected initial letter .
34 COMMON INTERF ACE The Common Interface (CI) of the UFS 822 is suitable for the use of two CA (Conditional Access) modules. These two CI slots are located at the bottom left on the front.
35 Y ou can fi nd out which Conditional Access modules are in the CI slots on the UFS 822 and which Smartcard is in which CA module from the “Main Menu” under “System Setup”, and the “Common Interface” menu. Con fi rmation is by pressing the button.
36 COMMON INTERF ACE Information for Conax, SECA, Viaccess and CryptoW orks users: Note that with monthly activation intervals, the programme providers have different procedures for activating pay TV cards. Activation may therefore be a few days before or after the beginning of a new month.
37 Select the “System Setup” menu using the menu button , the buttons on the main menu and . SYSTEM SETUP The selected menus, sub-menus and positions, as well as the parameters to be set, are each highlighted in colour . The menus are to a large extent self-explanatory .
38 SYSTEM SETUP Select the type of video signal at the Scart socket here. Select the signal that your TV set can process. Refer to the operating instructions for your television set! • FBAS – comp.
39 Here you specify whether your TV set is a • P AL or • NTSC deviceset. Select the screen display mode here: • for TV type “4:3”: “Pan & Scan” or “Letter-Box” • for TV type .
40 SYSTEM SETUP Set the variance from UMTC (Universal Mean T ime Coordinate; formerly Greenwich Mean T ime) here. At the bottom of the screen you see a listing of major cities to provide an indication.
41 SYSTEM SETUP Choose between Summer and Winter time. In the example on the previous page, Summer time was selected. SUMMER TIME/WINTER TIME Select the current date here. Press the button to display a calendar . Select the day using the cursor buttons ( ).
42 SYSTEM SETUP See “Common Interface” section Choose between Summer and Winter time. In the example on the previous page, Summer time was selected. SUMMER TIME/WINTER TIME If you have selected automatic time mode, set the channel here from which you want the receiver to get the time.
43 Press the button to access the “STB Management” menu. The following screen appears: Press the button to view the current software version. Press the button again to close the display . When you press the button you are asked whether you want to reset all settings to their factory defaults.
44 SA TCO-DX Press the button and enter the unit ID here. This is useful for identi fi cation in case of theft. The alphanumeric input procedure is as described in the “Alphanumeric Inputs” section. In the example shown here the ID “UFS 822” has been assigned.
45 Press the button to access the “HDD Management” menu. The following screen appears: HDD MANAGEMENT Con fi rm the displayed message with the button. The next time you switch on your receiver , your UFS 822 will display the following message (example): RCU 2 (Exit + 2) .
46 SYSTEM SETUP When you press the button you are asked whether you want to delete all photos/images. Use the buttons to select “OK” and start the reset by pressing the button.
47 SYSTEM SETUP Formatting irrevocably deletes all data on the storage medium! Use the buttons to select the transponder frequency and type of partitioning. Y ou have the following options: - Option 1: T ype of formatting F A T 32, complete hard disk (for Windows XP , MAC, Linux user) - Option 2: T ype of formatting EXT3, max.
48 Press the button to access the “Ethernet Setup” menu. The following display appears (example): ETHERNET SETUP Press the buttons to select whether or not the receiver should display the radio text when in radio mode (this option is available only from software version 1.
49 Use the buttons to select the “Get IP Address” fi eld and con fi rm by pressing the button. Y our DHCP server now indicates the IP address to the receiver .
50 USER PREFERENCES Select the “User Preference” menu using the menu button , the buttons on the main menu and . Use the buttons to select further options. If there is another sub-menu layer , press the button to open it.
51 USER PREFERENCES Use the buttons to select the time after which you want the UFS 822 to automatically switch off (standby). The minimum time you can set is 15 minutes, and the maximum 360 minutes. Each press of the buttons increases or reduces the power-off time by 15 minutes.
52 USER PREFERENCES Use the buttons (On/Off) to choose whether use of the receiver should be protected by a four-digit PIN. When switching the unit on from Standby , you are then prompted to enter the PIN. If the PIN is not entered the receiver cannot be operated.
53 Press the button to replace the old PIN with a new one. Enter the new (four-digit) PIN. For security you must repeat the new PIN code once again. On the screen which then appears use the buttons to select “OK” and con fi rm the changed PIN by pressing the button.
54 USER PREFERENCES Use the buttons to select the time after which you want the on-screen play information display to be automatically cancelled. Y ou can choose between 5, 8, 10, 12 and 15 seconds, or “Hide”. Use the buttons (On/Off) to specify whether the volume bar is displayed when adjusting the volume.
55 On this menu you can make settings for your recordings and for timeshifting. PVR SETUP Use the buttons to select whether automatic timeshifting is enabled or disabled. When you select “On” the receiver automatically (in the background) starts recording the programme you are viewing as soon as you switch to the channel.
56 USER PREFERENCES ONE-TOUCH RECORDING INFO WINDOW Use the buttons here to select the default recording time. If you forget to stop a recording you started manually , it is automatically stopped by the receiver when the default recording time elapses.
57 USER PREFERENCES In this menu you can use the button to delete the stored tvtv data. Y ou can then have the UFS 822 update the tvtv data at the selected time or press to switch your receiver to standby . The receiver automatically starts updating the tvtv data.
58 VIDEOTEXT (TELETEXT) This symbol in the channel noti fi cation shows you whether Videotext/T eletext is available for the selected channel. When you press the button, the receiver processes the broadcast Videotext/T eletext service for your TV set to display , even when the signal is encrypted.
59 Select the “Organize Channels” menu using the menu button , the buttons on the main menu and . This menu is password-protected and can only be accessed by entering the password. The factory default password is “0000”. The factory pre-programmed channel lists can be changed on this menu.
60 ORGANIZE CHANNELS Select the channel you want to lock using the cursor buttons ( ) and press the button to activate the lock. Press again to unlock the channel.
61 ORGANIZE CHANNELS • by satellite ( ! (green) button) • by favorites list ( " (yellow) button) • by alphabetical or numerical sequence ( # (red) button) Select the sort order you want to apply using the buttons and con fi rm with the button.
62 Select the channel you want to delete using the cursor buttons ( ) and press the button to mark it as deleted. The channel name is underlined in red. Press the button again to cancel your channel selection for deletion (this will only work as long as you have not yet quit the menu by pressing the button).
63 ORGANIZE CHANNELS Press the button to access the “Edit TV Favorites” menu. The following screen appears: Press the button to access the menu. Y ou can now use the on-screen keypad (operated as described under “Alphanumeric Inputs”) to name the next free Favorites list.
64 ORGANIZE CHANNELS Note: Only the favorites list is deleted; the channels in the favorites list are retained. Press the button to access the menu. Use the buttons to select the favorites list to/from which you want to add or delete channels and con fi rm your selection with the button.
65 TWIN FUNCTIONS The UFS 822 is equipped with two tuners, enabling you to perform two separate functions at the same time, this includes the functions: • Picture-in-Picture (PIP), • T imeshift and • One-touch recording. The picture-in-picture function permits simultaneous viewing of two programmes.
66 The timeshift function is described in the “T imeshift” section. Note that the receiver switches to hard disk mode when executing this function.
67 TIMESHIFT If you cannot catch the beginning of a programme because you are occupied with something else, or if you have to break off watching whilst a programme is being transmitted, you can watch it in timeshift mode. Press the button to activate this function.
68 TVTV EPG AND TIMER The EPG is a latest-generation Electronic Programme Guide. It provides all the EPG information for around 60 TV channels at no charge, without you having to change channel, and also of fers schedule information up to a week ahead (depending on programme provider).
69 TVTV EPG AND TIMER The EPG automatically displays the “Current” view when fi rst accessed, highlighting the current selected channel and the current programme. In the main window you see the channel number at the left, the channel name and current programme in the centre, and a progress bar at the right.
70 TVTV EPG AND TIMER Press the " (yellow) button to access the schedule for the channel to which you are currently tuned in the EPG. The following display appears (example): Press the cursor buttons ( ) to scroll line-by-line or page-by-page through the programme list of the selected channel.
71 A tip is shown for each day , up to a week ahead. Y ou can use the buttons to view the following programmes on the Highlights menu by category (e.g. Series, Sport, News, Magazine/Reportage, Kids ...). Within each category you can scroll line-by-line or page-by-page as usual using the cursor buttons ( ).
72 Pressing the button on the EPG allows you to search through all the information available to the EPG (programme name, description, title, cast, director , details) for a word or phrase you enter , with the results being displayed in a list. Press the button to switch to “Search”.
73 TVTV EPG AND TIMER SEARCH STORAGE Y ou can save individual search terms in the search memory . T o do this, enter the search term, as described on the previous page. Press the button to load the search term into the memory . Now select the memory location using the buttons.
74 When you call up additional information in the EPG using the button, you will be shown only the fi rst page of description of the programme. T o obtain the full information on the programme, set the item “EPG Grabbing” in the “User Preference”/”EPG Setup” menu to “Off”.
75 Y ou can programme a recording from the various views of the EPG (“Current”, “Programme list”, “Highlights” and “Detailed information”) and from within their various sub-menus. When programming recordings, the EPG automatically adapts to the actual SA T IF input signal mode (Single/Loop through/Double T uner).
76 • Recording status (once, daily , weekly , user-de fi ned, series) - selected using the buttons. • Date (advanced day-by-day) - selected using the buttons. • Start time (advanced minute-by-minute) - selected using the buttons or entered directly using the numeric pad.
77 Example of user-de fi ned recording: Example of series recording: Note: If every episode of a series is programmed to be recorded using the “Series recording” function, the EPG locates the series in question in the updated schedules and automatically programmes recording of them.
78 In the box at the bottom right of the screenshot above you see the day , date and time of recording and the recording mode. Overlaps are indicated in orange text. Use the buttons to move to the orange listing and you will see the overlapping recording shaded in white (see screenshot above).
79 • The button does not become active until 15-20 seconds after the picture appears on the TV . • Updating of the EPG is only started if the EPG data is more than 36 hours old. • The EPG is broadcast over the ASTRA satellite at the frequency of 12,603.
80 The channels in the table below are provided with EPG data on Kathrein receivers as at 09.02.2006. The assignment of the channels below to the EPG may change at any time! 3sat MDR Fernsehen Sky New.
81 AUDIO SETTINGS The required volume level can be set using the % buttons on the remote control of the receiver . A bar indicator is displayed on the screen to show the set volume. Press the button to mute the sound. “Mute” is displayed. Press the button again to restore the sound.
82 AUDIO SETTINGS Example: Y ou can for instance create a favorites list with the name “Dolby Digital” in the “Organize Channels”, “Edit TV Favorites” menu.
83 RECORDING The UFS 822 offers you the following options for recording a programme: - Timeshift Allowing you to include the background recordings made up to that point to be included in your recordin.
84 RECORDING Y ou can start recording the programme as from the point you switched to the channel in question simply by pressing the button, or you can simply wait the 5 seconds for automatic recording to begin.
85 RECORDING If there is an overlap with another scheduled or ongoing recording, this fact is indicated. The receiver then presets the end time for your new recording as the start time of the overlapping programme (see “Duration/End” at the right).
86 RECORDING If there is an overlap with another scheduled or ongoing recording, this fact is indicated. The receiver then presets the end time for your new recording as the start time of the overlapping programme (see “Duration/End” above). Duration/End Y ou can specify the duration of a recording regardless of when it starts.
87 SETTING BOOKMARKS DURING THE RECORDING During the recording you can set bookmarks, as described below under “Bookmarks”. This allows you to set bookmarks at speci fi c points of the recording, so that when you view the recording on subsequent occasions you can skip certain parts of the programme, such as the commercial breaks.
88 RECORDING LIST Press the button to switch from the normal view to the folder view . Now use the buttons to select between the normal view and the folder view . Furthermore, you will be able to specify which folder your fu- ture recordings are to be saved to (in the second line).
89 Use the # (blue) button to choose between TV and radio recordings within the recording list. By pressing the ! (green) button, you can sort recordings according to the following criteria: - Date of.
90 Button (play) - Start play - End fast forward/rewind and resume playback - End pause and resume playback - Display the playback progress bar in playback mode (shows the overall duration of the .
91 - After playback has been paused using the button, you can press the button to start slow-motion winding. Every time the button is pressed, the slow-motion speed will be increased one step.
92 Y ou can record encoded programmes even when the CA module with the Smartcard is not inserted. However , to view what you have recorded the CA module with Smartcard must be inserted in the Common Interface on the receiver .
93 RECORDING LIST - USB (for recordings only) - Merge (for recordings only) - Change T ype (deletion block) (for recordings only) - Lock (for recordings only) At the bottom of the screen, you will also view the option “Create New Folder” (access with button).
94 DELETE RECORDINGS/FOLDERS T o delete recordings: Select the recording to be deleted with the buttons and con fi rm by pressing the button. The selected recording will be crossed out in red and the selection cursor will automatically jump to the next recording.
95 MOVE (RECORDINGS TO A FOLDER) Use the buttons to select the recording to be moved and con fi rm by pressing the button. The recording will be marked with a white “+” symbol on.
96 RECORDING LIST The receiver automatically starts playing back the recording. Y ou now have several options for specifying the range to be copied (see example bar): Start Middle End T o set the exac.
97 Copy the range marked “End” as follows: - Move to the start of the range you want to copy and press the button. Then press the ! (red) button to set the start point marker of the range to be copied. Then press the ! (green) button to automatically mark the full range to the end of the recording.
98 The receiver automatically starts playing back the recording. Y ou now have several options for specifying the range to be cut (see example bar): T o set the exact times for the start and end marke.
99 USB Use this function to copy recordings saved on your hard disk to an external USB storage medium that has been connected to the rear panel of your receiver . Select the recording to be transferred using the buttons and con fi rm by pressing the button.
100 RECORDING LIST MERGE Y ou can use this function to merge together two or more recordings on one channel. Make sure you have also selected “Merge” with the (red) button. Use the to select the recordings you want to merge, then press the button.
101 Use the buttons to select “OK” and pres the button to start merging the recordings. The receiver merges the two recordings. The newly created single recording is assigned the name of the fi rst recording you selected for merging.
102 RECORDING LIST BOOKMARKS Y ou can use this function to divide recordings into chapters, or to fi nd speci fi c sequences in a recording very quickly . SETTING BOOKMARKS Start a recorded programme by pressing the button. When the playback reaches the point at which you wish to set a bookmark, press the (red) button.
103 Use the buttons in the “Chapters” menu to select the bookmark to be deleted. Then press the (red) button. Use the buttons to select “OK” within the message that is displayed, and con fi rm again by pressing the button.
104 MUL TIMEDIA/GAMES Select the “Multimedia/Games” menu using the menu button , the buttons on the main menu and . The following display appears (example): Select the function you want, using the buttons and con fi rm with the button.
105 MUL TIMEDIA/GAMES MP3 PLA YER Use the buttons to select the desired directory and press the button to open the directory and access its subfolders. In the above example the fi rst directory listed is the local hard disk of the UFS 822 (Local HDD).
106 MUL TIMEDIA/GAMES The MP3 player automatically starts playing the fi rst fi le you selected. Y ou now have the following options: - Use the buttons to skip to the next/previous track - Us.
107 MUL TIMEDIA/GAMES Select the folder or fi le you want by pressing the button. Y our selection is marked by a “+” sign at the end. Y ou now have the following options: - Press the ! (green.
108 Use the buttons to select the desired directory and press the button to open the directory and access its subfolders. In the above example the fi rst directory listed is the local hard disk of the UFS 822 (Local HDD). The second directory is a USB memory stick.
109 The slide show starts automatically with the fi rst selected photo. Y ou now have the following options: - Press the button to show the slide show help bar (see screenshot above, lower part) - Press the button to stop the slide show and then use the buttons to scroll back and forth through the individual photos.
11 0 Y ou can organise the fi les on the “JPEG Files” menu. For this, press the " (yellow) button. The following display appears (example): Select the folder or fi le you want by pressing the button. Y our selection is marked by a “+” sign at the end.
111 Not yet available in the current software version. MUL TIMEDIA/GAMES GAMES APPLICA TIONS No games are currently available for the UFS 822..
11 2 MUL TIMEDIA/GAMES Use the buttons to select the desired directory , and press the button to open the directory and access its subfolders. In the example shown above there is only a single directory , which is the enabled folder on the hard disk of the PC/laptop.
11 3 MUL TIMEDIA/GAMES Use the buttons to select the desired directory and press the button to open the directory and access its subfolders. In the above example you see the USB stick on the USB 2.0 host output as the fi rst directory , and the enabled folder on the PC/laptop as the second directory .
11 4 INST ALLA TION MENU Select the “Installation” menu using the menu button , the buttons on the main menu and . Use the buttons to select further options. If there is another sub-menu layer , press the button to open it.
11 5 INST ALLA TION MENU Use the buttons to select whether you want to use only tuner 1 (single mode) or both tuners (dual mode). In dual mode (both tuners receiving a dedicated signal or the signal from tuner 1 is looped- through to tuner 2) a SA T IF signal must be connected to both tuners.
11 6 INST ALLA TION MENU TUNER 1 SETUP Antenna Number: Each tuner can receive from up to four satellites. Use the buttons to select the position to which you want to assign a new or different satellite. Satellite Name: Press the button to access the list of available satellites.
11 7 INST ALLA TION MENU DiSEqC™1.0: Press the buttons to make your selection. - 1 of 4: for the fi rst satellite of the tuner - 2 of 4: for the second satellite of the tuner - 3 of 4: for t.
11 8 INST ALLA TION MENU AUTOMA TIC SEARCH Network Search: Use the buttons to select the setting for the network search. If you set the network scan to “On”, the transponder network enables additional transponders that have not yet been stored to be located.
11 9 INST ALLA TION MENU MANUAL SEARCH Select T ransponder: Press the button to call up a list of available stored transponders on the satellite you previously selected. Use the buttons to select the transponder you want. If the transponder you want is not listed, select the “Enter New T ransponders” option.
120 INST ALLA TION MENU Network Search: Use the buttons to select the setting for the network search. If you set the network scan to “On”, the transponder network enables additional transponders that have not yet been stored to be located. They are then stored and searched for new channels in the same way as the existing transponders.
121 Video PID (Packet Identi fi cation Number): Use the numeric pad on your remote control to key in the video PID (Packet Identi fi cation Number) identifying the video data of the new channel you want on the transponder .
122 INST ALLA TION MENU Use the buttons to select the tuner for which you want to make the settings and con fi rm your menu selection by pressing the button. The settings for both tuners are performed in the same way . Select Satellite: Use the buttons to select the desired satellite here.
123 INST ALLA TION MENU Action: Pressing the button on the “OK” button allows the “Stop”, “Save”, “Limits Off” and “Reset” actions to be activated. Y ou can also press the ! (green)/ (red) buttons here to stop ongoing rotations and save the current position.
124 Satellite Name: Press the button to access a list of all stored satellites. Use the buttons to select the satellite you want. T ransponder Frequency: Use the buttons to select the transponder frequency . Edit Satellite Longitude: Use the numeric pad to key in the new longitude.
125 Satellite Name: Press the button to access a list of all stored satellites. Use the buttons to select the satellite you want. T ransponder Frequency: Use the buttons to select the transponder frequency .
126 INST ALLA TION MENU See “Software and Programme List Update” section ON AIR DOWNLOAD Edit T ransponders: Here you can input the “Frequency”, “Polarization” and “Symbol” to edit the transponder . Press the button to con fi rm the settings.
127 CONNECTING UP THE VIDEO/PVR For details of how to connect your external recorder to the receiver refer to the connection diagram provided at the end of this manual and the instructions for the external recorder .
128 SOFTW ARE AND PROGRAMME LIST UPDA TE Thanks to digital technology , you can receive satellite updates of the software and programme list for your receiver . The “On Air Download” sub-menu on the “Installation” menu tells you whether new software or programme lists are available.
129 SOFTW ARE AND PROGRAMME LIST UPDA TE The transponder information “Frequency” and “Symbol Rate” are displayed here. The current software version is displayed here. Use the buttons to select whether you want to download the latest information text.
130 SOFTW ARE AND PROGRAMME LIST UPDA TE The receiver starts downloading. On the next screen you see the following: - The number of modules being downloaded - The elapsed time - The current operation .
131 SOFTW ARE AND PROGRAMME LIST UPDA TE Follow all on-screen instructions! Check the time setting following a software update! Y ou can also download the updates from the Internet.
132 PVR MANAGER The Ethernet port (10/100 base T) and the “PVR-Manager” software available for download enable you to integrate the receiver into your home network.
133 USING THE FRONT P ANEL If you have misplaced your remote control, or if the batteries are fl at, you can still operate your receiver from the front panel. BACKUP OPERA TION The front panel houses four buttons and the multifunction control (from now on referred to as “the control”).
134 RECEIVER T O RECEIVER DA T A TRANSFER Y our receiver is able to receive data from another receiver via its RS232 port. For this, the two receivers are connected with a null modem cable. The transmitting receiver is the “master”, and the receiving receiver is the “slave”.
135 TECHNICAL APPENDIX TECHNICAL FEA TURES The UFS 822 twin DVB-S receiver is fi tted with two independent reception and signal processing systems, making it possible to record a broadcast and simultaneously zap through other channels.
136 TECHNICAL APPENDIX T ype UFS 822si UFS 822sw Order no./Colour 202101 19/Silver 20210120/Black RF range Sat-IF range MHz 2 x 950-2150 Input level range dBµV 44-83 Reception threshold (EB/NO) dB < 4.
137 1 infrared remote control (RC 660) 2 batteries 1.5 V , type: LR 03, size: AAA (micro) 1 Scart cable 1 operating manual Signal Pin no. TV VCR/AUX Right audio output 1 X X Right audio input 2 X Left.
138 TECHNICAL APPENDIX CONNECTION EXAMPLES Conventional DiSEqC™ system Hi- fi system Dolby Digital system Digital audio AC 3 optical.
139 Sat-ZF 950-2150 MHz UAS 484 T errestrische Antenne **) ESU 33 Single RTL Television 712 ESU 33 Single RTL Television 712 ESU 33 Single RTL Television 712 ESU 33 Single RTL Television 712 terr. H low/0kHz V 1-4 V high/22kHz H 1 = SCR(0) 1400 MHz 2 = SCR(1) 1516 MHz 3 = SCR(2) 1632 MHz 4 = SCR(3) 1748 MHz EXR 551 ERA 14 ERA 14 LCD.
140 UAS 481 Single-cable feed system ERA 14 ERA 14 Note: A maximum of two UFS 822s can be operated on this system. Connect the tuner input “1” to the socket and loop the signal to the tuner input “2” (connect LNB 1 “Loop-through output” to LNB 2 input).
141 TECHNICAL APPENDIX CONNECTION EXAMPLES FOR THE NETWORK-FUNCTION PC/Laptop Gekreuztes Netzwerkkabel IP-Adresse: 192.168.0.10 IP-Adresse: 192.168.0.1 1 DHCP (Receiver): OFF IP address: IP address: C.
142 TECHNICAL APPENDIX PC/Laptop Netzwerkkabel Switch/HUB TCP/IP-Adresse: 192.168.0.12 PC/Laptop Netzwerkkabel Netzwerkkabel TCP/IP-Adresse: 192.168.0.
143 TECHNICAL APPENDIX PC/Laptop Netzwerkkabel DHCP-Server , Router (z. B. Fritzbox) PC/Laptop Netzwerkkabel TCP/IP-Adresse: 192.168.0.13 TCP/IP-Adresse: 192.
144 TECHNICAL APPENDIX DHCP (Receiver): ON PC/Laptop Netzwerkkabel DHCP-Server , Router (z. B. Fritzbox) TCP/IP-Adresse: automatisch Funkstrecke Network cable DHCP sensor , router (e.
145 TECHNICAL APPENDIX PC/Laptop Netzwerkkabel DHCP-Server , Router (z. B. Fritzbox) TCP/IP-Adresse: automatisch PC/Laptop Funkstrecke DHCP (Receiver): ON TCP/IP address: automatic Network cable Broadcast path DHCP sensor , router (e.
146 TECHNICAL APPENDIX PC/Laptop Netzwerkkabel DHCP-Server , Router (z. B. Fritzbox) PC/Laptop Funkstrecke Netzwerkkabel TCP/IP-Adresse: automatisch TCP/IP-Adresse: automatisch DHCP (Receiver): ON TCP/IP address: automatic TCP/IP address: automatic Network cable Network cable DHCP sensor , router (e.
147 SHORT TECHNICAL GUIDE DiSEqC™ DiSEqC™ (Digital Satellite Equipment Control) is a communication system between a satellite receiver (master) and the peripheral satellite components (slaves), such as LNBs, multi-switches, rotating antenna systems.
148 SHORT TECHNICAL GUIDE PIP Picture In Picture function PID The PID (Packet IDenti fi cation) number is an identi fi cation number for video signals and audio signals in the digital data stream of DVB-MPEG-2 signals. The receiver uses the PID number to create a unique assignment for the video and audio data transmission.
149 SHORT TECHNICAL GUIDE AC 3 Output for Dolby Digital signal Audio output Sound output on the receiver A V programme pos. Preferred programme position on TV set for Scart input CA Conditional Access.
150 TROUBLESHOOTING In the event of a malfunction, fi rst check all the cable connections and operating states: 1. Receiver and TV set power plugs are connected to the wall socket 2. Antenna cables are located on the receiver input 3. Receiver and TV set correctly interconnected by a Scart or cinch cables 4.
151 AC 3 .............................................................................................................................. ....... 82 ACCESSING THE TVTV EPG .................................................................................
152 DECODING A RECORDING .................................................................................................... 92 DET AILED INFORMA TION ...................................................................................................
153 IMPORT ANT ADDITIONAL INFORMA TION .............................................................................. 79 IMPORT ANT INFORMA TION .................................................................................................. 34 INFORMA TION ABOUT ANTENNA CONNECTION AND “LOOP THROUGH” OPERA TION .
154 REMOTE CONTROL BUTTONS AND THEIR FUNCTIONS IN PLA Y -BACK MODE ...................... 90 REMOTE CONTROL RC 660 .................................................................................................. 14 SCART SOCKET ASSIGNMENT ..........
155 SER VICE If, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly , or if unexpected problems occur , please contact your specialist dealer .
Internet: http://www .kathrein.de KA THREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 P .O. Box 100 444 • 83004 Rosenheim • GERMANY 936.3283/A/0408/ZWT - T echnical data subject to change.
An important point after buying a device Kathrein UFS 822sw (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kathrein UFS 822sw yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kathrein UFS 822sw - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kathrein UFS 822sw you will learn all the available features of the product, as well as information on its operation. The information that you get Kathrein UFS 822sw will certainly help you make a decision on the purchase.
If you already are a holder of Kathrein UFS 822sw, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kathrein UFS 822sw.
However, one of the most important roles played by the user manual is to help in solving problems with Kathrein UFS 822sw. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kathrein UFS 822sw along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
