Instruction/ maintenance manual of the product CAP 210 Kathrein
Go to page of 36
Installation Manual MobiSet 2 digital CAP 210 and Mobi Set 3 digital CAP 310.
2 Important information about MobiSet 2 digital CAP 210 Information for Owners of MobiSet 2 digital CAP 210! The HTV 1 15 LCD/TFT television set is only included with the CAP 310! If you have purchase.
3 Foreign language installation instructions Electronic equipment is not household waste in accordance with directive 2002/96/EC OF THE EUROPEAN P ARLIAMENT AND THE COUNCIL dated 27 th January 2003 on used electrical and electronic equipment, it must be disposed of properly .
4 1. Roof duct with mounting nut 2. Mounting plate 3. T urntable 4. Antenna boom 5. BAS 60 HDP 171 UFD 170 For an explanation of the connections, see the “Connection Examples” section and operating manual UFD 170.
5 • T urntable with fi tted BAS 60 and ready for connection cables with a length of 3.5 m • Power supply cable (10 m) for connection to on-board network • Mounting plate • Roof duct with seal.
6 Proper use The MobiSet 3 digital CAP 310 is designed to receive digital TV and radio programs via satellite. The turntable is intended for the Kathrein planar antenna BAS 60. This antenna can be used to receive digital TV and radio signals in the frequency range from 10.
7 Safety instructions - important notes When carrying out installation work in locations with a risk of falling, take appropriate safety precautions, e.g. use of a working platform. Make sure that the vehicle roof is suf fi ciently strong and stable to carry out the installation work (risk of damage or collapse of roof).
8 Fundamental information A crucial safety factor is proper performance of installation and electrical connection work, and the speci fi ed alignment of the turntable in the direction of travel (park position), see also installation and connection. Heed as precisely as possible the installation conditions and steps described.
9 Operate the system from your vehicle‘s battery (12 V) or a suitable mains power pack. This mains power pack must guarantee a stable initial voltage of 12 V , 1 1 A continuous current and 15 A (300 ms) surge current. The transient power consumption is up to a maximum of 12 A.
10 Safety instructions - important notes Instructions for installation and operation of the HDP 171 with the UFD 170 1. The turntable can only be used in conjunction with a Kathrein UFD 170 Caravan Digital Combi Receiver or a Kathrein UFD 540 Caravan Digital Receiver with HDS 160 control unit.
11 Safety instructions - important notes 3. Connecting the power supply cable lead marked “Ignition” activates the turntable function for automatic lowering of the antenna. This lowering takes place as soon as the vehicle ignition circuit is turned on.
12 Installation and connection Required tools and equipment • Circular cutter , Ø 38 mm • Flat-bladed screwdriver for M5 screws • Drilling machine • Galvanised tallow drop screws, depending o.
13 • T o ensure secure adhesion, the height difference of the roof curve may not be more than 1 cm over a length of 2 m, as otherwise the gap between the roof and the mounting plate would be too big to be fi lled by the sealing glue.
14 Installation and connection Installation steps Installation of cable duct and mounting plate Note: If you have previously used a Kathrein HDM140/141 fl exible satellite mast or another mast with a diameter of 34 mm, you can continue using the existing duct hole in the roof (if space allows).
15 Installation and connection • For very thin roof panel materials and insuf fi cient support in the insulating material, through holes (Ø: 5.5 mm) into the interior of the vehicle are necessary and galvanised M5 tallow drop screws of suf fi cient length should be used.
16 Installation and connection Figure: D • Note before starting glueing work that the optimal processing temperature of materials to be glued and the sealing glue is between +15 °C und +25 °C. Prepare all necessary fastening elements and tools. • Prepare the tube of sealing glue in accordance with the instructions enclosed with the tube.
17 Installation and connection Installation of turntable V ersion with cable duct below turntable (Fig. E) • Check that the O ring is correctly positioned in the groove of the cable duct (Fig. A). An incorrectly positioned or missing O ring will allow water to penetrate.
18 Installation and connection V ersion with external cable duct (Fig. F) • Arrange the cables in the cable duct when placing the turntable onto the mounting plate. Make sure that the cables are not crossed over and that they are tightened so that they cannot be kinked.
19 Installation and connection Brief instructions for installing the HDP 171 The sequence of pictures shown illustrates all the necessary installation steps that are required to assemble the HDP 171 turntable and the BAS 60 planar antenna on the roof of the vehicle.
20 Set up electrical connections. Connect UFD 170/UFD 540 receiver . Connect connecting/control unit to battery . Installation and connection The antenna must always be lowered into horizontal positio.
21 Installation and connection Laying cables and connecting the turntable HDP 171 • Lay the control cable (8-pole W estern connector), the coaxial cable and the power supply cable (2-pole connector) to the UFD 170. Avoid laying the cables across sharp edges and secure the cable against possible abrasion points.
22 Installation and connection Connecting the HTV 1 15 LCD TV Set Connect a HTV 1 15 and the receiver with the included cinch/cinch cable included with the UFD 170. Make sure that you heed the colour identi fi cation of the connectors and outlets on the back side of the receiver .
23 Connection example motorhome - 12 V battery connection (UFD 170) Installation and connection Attention: For operation with two batteries, it must be ensured that the ignition signal earth has the same potential as the power supply battery earth for the UFD 170 combi receiver .
24 Connection example caravan - 230 V battery connection (UFD 170) Installation and connection Fig: H 8-pole 6-pole brown white green Note! Do not connect.
25 BAS 60 planar antenna Proper use The BAS 60 fl at antenna is used to receive digital TV and radio signals in the frequency range from 10.70 to 12.75 GHz. It cannot receive terrestrial signals. The BAS 60 has been designed for mobile use, to receive satellite signals in stationary caravans, motorhomes or trucks.
26 BAS 60 planar antenna The footprint is the reception area on the earth that a satellite covers with its transmission beam (spot), within which satellite reception is possible. The transmission power is at its greatest in the centre of this spot – it becomes progressively weaker moving outwards.
27 Polarisation setting Polarisation setting As supplied, the BAS 60 is mounted centrally on the turntable. In this position, you can also receive signals from satellites with deviations in the degree of longitude (of the typical reception range) of between 15° and 20° from the orbit position of the satellite.
28 We strongly advise that users who are not familiar with the installation work should not reassemble the BAS 60 independently . They should contact a technician or engineer .
29 Polarisation setting T o dismantle/install the planar antenna from the turntable, proceed as follows: (the key names refer to the remote control for the UFD 170 receiver) 1. Turn on the receiver with the main switch on the front of the unit. 2. Press the Standby button ( ) to start up the receiver .
30 View after installation +15° View after installation in the middle (standard) View after installation -15° Installation and connection.
31 Dismantling for servicing If repairs to the system or individual components are necessary , contact your specialist dealer or our service centre (see below for address).
32 T echnical data Dimensions (mm) Driving direction.
33 T echnical data Electric data Supply voltage 10.9…13.8 V Ignition signal 12…24 V “Standby” current 20 mA “ENGINE ON” current 5...8 A T ransient start-up current 12 A Azimuth rotation range 0…370° Elevation rotation range 10…90° Search time for fi rst satellite (typ.
34 Sika fl ex ® 291 data sheet.
35 Sika fl ex ® 291 technical data sheet.
Declaration of conformity 936.2712/B/0306/ZWT - T echnical data subject to change. Internet: www .kathrein.de KA THREIN-Werke KG • Anton-Kathrein-Strasse 1 - 3 P .
An important point after buying a device Kathrein CAP 210 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kathrein CAP 210 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kathrein CAP 210 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kathrein CAP 210 you will learn all the available features of the product, as well as information on its operation. The information that you get Kathrein CAP 210 will certainly help you make a decision on the purchase.
If you already are a holder of Kathrein CAP 210, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kathrein CAP 210.
However, one of the most important roles played by the user manual is to help in solving problems with Kathrein CAP 210. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kathrein CAP 210 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
