Instruction/ maintenance manual of the product V1700CG JVC
Go to page of 24
INSTRUCTIONS DT -V1700CG MUL TI-FORMA T MONIT OR VOLUME SLOT 1 A B DEGAUSS MENU BLUE CHECK ASPECT AREA MARKER UNDER SCAN PULSE CROSS COLOR OFF SLOT 2 C D SLOT 3 POWER E F INPUT SELECT For Customer Use: Enter below the Serial No. which is located on the rear of the cabinet.
SCREEN BURN ● It is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright images on screen. This may cause a burning (sticking) phenomenon on the screen of cathode-ray tube. This problem does not occur as far as displaying normal video playback motion images.
ENGLISH 3 Fuse POWER CONNECTION The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries or United Kingdom), the power cord attached conforms to the following power supply voltage and countries.
CONTROLS AND FEA TURES FRONT VIEW <Front Panel> T ally lamp Lights when the tally control signal is ON. The tally control signal is input through the MAKE remote terminal. For details, refer to Page 17. PHASE adjustment knob Adjusts picture hue.
ENGLISH REAR/SIDE VIEW <Rear Panel> COLOR OFF button/lamp Press the COLOR OFF button. The button lights and the screen becomes monochrome. When the COLOR OFF button is pressed while lit, the light goes off and the normal screen is restored. Use this function to confirm the noise in the brightness signal or to confirm the white balance.
Video input/output terminals Input (IN) and output (OUT) terminals for component (colour deference) or RGB signals. The IN and OUT terminals are bridge-connected. (When no cable is connected to the OUT terminal, the input signal is automatically terminated.
ENGLISH 䡵 SDI INPUT CARD (OPTIONAL: IF-C01SDG) AUDIO 2 AUDIO 1 OUT IN SWITCHED OUT SDI 1 SDI 2 IN IN 1 2 3 4 Output terminal for a selected component serial digital signal Output terminal for s selected digital signal (the input displayed on the screen).
PREP ARA TION 1. Turn of f the Multi-Format Monitor ’ s main power and unplug the power cable from the AC outlet. 2. Unscrew the screws and remove the slot cover from the slot (on the rear side of the monitor) in which you are going to install the card.
ENGLISH BASIC MENU OPERA TIONS (MAIN MENU, SETUP MENU) 䡵 ABOUT MENU SCREENS This monitor features a MAIN MENU (main menu screen) and a SETUP MENU (setup menu screen). The MAIN MENU contains the functions normally used, and the SETUP MENU contains the settings required for initial setup.
HOW TO USE “MAIN MENU” 䡵 “ MAIN MENU ” ITEMS The following items appear in MAIN MENU. Items Functions Displays 1 APERTURE CONTROL Compensates the frequency characteristics of the input video signal. * 1 2 SLOT CONDITION Displays the status of the input cards installed in each of the input card slots.
ENGLISH 1. APERTURE CONTROL Compensates the frequency characteristics of the input video signal. Press the button to display the setting menu illustrated on the right. NOTE : APERTURE CONTROL is not displayed when the RGB signal is input. ● INPUT A/B corresponds to SLOT 1, INPUT C/D to SLOT 2, and INPUT E/F to SLOT 3.
Input Signal Format Standard Manual setting setting (MANUAL) NTSC, P AL, 480/60i, ITU601 480/60p, 576/50i, 575/50p ITU709 720/60p, 1080/50i, 1080/60i, ITU709 1035/60i, 1080/24pSF <COLOR MATRIX> SELECT :MANUAL R-Y PHASE :90 R/B GAIN :0.86 G-Y PHASE :244 G/B GAIN :0.
ENGLISH HOW TO USE “SETUP MENU” 䡵 “ SETUP MENU ” ITEMS Items Functions 1 FUNCTION SETTING Displays the monitor’s power-up time or the total usage time. 2 PICTURE SUB ADJ. Performs approximate adjustments using the control knobs on the front panel.
HOW TO USE “SETUP MENU” (cont'd) <FUNCTION SETTING> COLOR SYSTEM :AUTO RUSH DELAY TIME :STD. HOUR METER X100h :000 EXIT: MENU ADJUST:- + SELECT: <PICTURE SUB ADJ.> CONTRAST :00 BRIGHT :00 CHROMA :00 PHASE :00 NTSC SETUP :00 COMPO.
ENGLISH <COLOR TEMP./BAL.> COLOR TEMP. :LOW BLUE DRIVE :000 RED DRIVE :000 GREEN CUTOFF :000 BLUE CUTOFF :000 RED CUTOFF :000 sub menu reset EXIT: MENU ADJUST:- + SELECT: <SIZE/POSI. ADJ.> H.SIZE :00 H.POSITION :00 V.SIZE :00 V.POSITION :00 sub menu reset EXIT: MENU ADJUST:- + S EL E C T: 3.
<STATUS DISPLAY> STATUS DISPLAY :ON 1080/1035 :1080 EXIT: MENU ADJUST:- + S EL E C T: <DISTORTION ADJ.> PINCUSHION :00 PIN.BALANCE :00 PARALLELOGRAM :00 TRAPEZOID :00 sub menu reset EXIT: MENU ADJUST:- + SELECT: 5. DISTORTION ADJ. Compensates the picture distortion.
ENGLISH HOW TO USE EXTERNAL CONTROL 䡵 ABOUT EXTERNAL CONTROL This multi-format monitor has two external control terminals. One is the MAKE terminal, which controls the monitor by connecting the terminals with many functions to the ground (GND) terminal.
HOW TO USE EXTERNAL CONTROL (cont.) 䡵 HOW T O USE THE RS-232C TERMINAL Y ou can control the monitor from your PC via the RS-232C terminal. For details on operating the monitor from the PC, consult your dealer or service centre for details.
ENGLISH Problems No power supply No picture with the power on No sound Wrong colour Unnatural picture Shaking picture Points to be checked Is the power plug loosened or disconnected? Is the signal cab.
Problems Irregular colour Wrong picture position, wrong picture size Front panel buttons and knobs do not function Points to be checked Is the monitor placed or moved close to a speaker or any other d.
ENGLISH SPECIFICA TIONS 䡲 T ype : Multi-format monitor 䡲 Picture T ube : 17" measured diagonally 䡲 Effective Screen Size : Width : 330 mm Height : 250 mm Diagonal : 410 mm 䡲 Scanning Freq.
䡵 Compliant Signal Formats of Each Input Card Input Signals IF-C01PNG IF-C01COMG IF-C01SDG IF-C01HSDG NTSC (3.58 MHz) R —— — P AL (4.43 MHz) R —— — Black-and-White (50 Hz/60 Hz) R ——.
ENGLISH SPECIFICA TIONS (INPUT CARD: OPTIONAL) 䡵 IF-C01COMG: COMPONENT/RGB INPUT CARD T ype : Component/RGB input card for multi-format monitor Inputs/Outputs : Component (Y , P B /B-Y , P R /R-Y) or RGB: 1 line, BNC connector x 6 (Y : 1 V (p-p), 75 Ω /P B , B-Y , P R , R-Y , R, G, B: 0.
24 JVC PROFESSIONAL PRODUCTS COMPANY DIVISION OF US JVC CORP. 1700 Valley Road Wayne, N.J. 07470 JVC CANADA INC. 21 Finchdene Square, Scarborough Ontario M1X 1A7 © 2001 VICTOR COMP ANY OF JAP AN, LIMITED Printed in Japan LCT0971-00 2 A 0 7 01-I-U-VP DT-V1700CG MULTI FORMAT MONITOR Untitled-1 01.
An important point after buying a device JVC V1700CG (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC V1700CG yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC V1700CG - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC V1700CG you will learn all the available features of the product, as well as information on its operation. The information that you get JVC V1700CG will certainly help you make a decision on the purchase.
If you already are a holder of JVC V1700CG, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC V1700CG.
However, one of the most important roles played by the user manual is to help in solving problems with JVC V1700CG. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC V1700CG along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
