Instruction/ maintenance manual of the product DT-V20L3D JVC
Go to page of 24
INSTR UCTIONS DT -V24L3D DT -V20L3D MUL TI FORMA T LCD MONIT OR Ta b le of Contents Safety Precautions .............................................. 2 IMPOR T ANT SAFEGU ARDS ........................... 2 Installation ................................
2 • Do not install this product in the f ollowing places: – in a damp or dusty room – where the product is exposed to soot or steam, such as near the cooking counter or a humidifier – near heat sources – where condensation easily occurs, such as near the window • Do not place this product on an unstable cart, stand, or table .
Dear Customer , This apparatus is in conf or mance with the v alid European directives and standards regarding electromagnetic compatibility and electrical safety .
4 Installation CA UTION • Do not rest your arm on the monitor or lean against the monitor . • Do not touch the LCD panel when installing the monitor . • Be sure to install the monitor securely to prev ent the monitor from falling o ver , which ma y cause damage to the monitor or injury .
5 To adjust the stand height To change the stand height, detach the stand from the monitor ( ☞ “T o detach the stand” on page 4). Then, change the position of the stand plate according to the stand height you w ant by choosing the screw holes to use .
6 Daily Operations / Connections 7 Fr ont panel p SAFETY MARKER button/lamp Displays/hides the saf ety marker . • Adjust the area of the saf ety marker in “MARKER” of the MAIN MENU ( ☞ page 11). • This function does not work when displa ying the picture in the 1:1 mode.
7 If you press the INPUT SELECT b utton of the current input, the status of the input signal and setting of muting are displa yed f or about 3 seconds. • Make the setting to displa y/hide the status in “ST A TUS DISPLA Y” of the “INFORMA TION” ( ☞ page 15).
8 7 Rear panel Daily Operations / Connections (cont.) The illustration of the monitor is of DT -V24L3D. 1 Po wer switch Tu r ns the po wer on or off. • Y ou need to press button ( ☞ u on page 6) to use the monitor after turning on the power switch.
9 7 Av ailable signals The follo wing signals are av ailable f or this monitor . Video signals No . Signal name Signal format shown in the status display ( ☞ page 7) Input terminal VIDEO (INPUT1, INPUT2) COMPO ./RGB (Analog component/ Analog RGB)* 1 E.
10 Menu Configuration—MAIN MENU PICTURE FUNCTION Setting for the picture quality Item T o do Setting value MO VING PICTURE * 1 Reduce the lag of moving pictures which is peculiar to LCD . OFF , ON APERTURE FREQ. * 2 Select the frequency of the luminance signal compensated in “APERTURE LEVEL.
11 Operation guide Shows the b uttons for each operation. • The menu automatically disappears in about 30 seconds after the pre vious operation. • Some items ma y not appear on the menu depending on the input or the input signal. • The items controlled b y the MAKE system do not appear on the menu.
12 Settings of “E.A UDIO GROUP” The setting values and selectab le audio channels of EMBEDDED A UDIO signals are as follo ws. 1G: channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G) 2G: channel(s) 5/6/7/8/5+6.
13 WA VE FORM SETTING* 1 Settings for the w av e form monitor Item T o do Setting value POSITION Select the position of the wa ve f or m monitor . 1 (lower right), 2 (low er left), 3 (upper left), 4 (upper right) FIL TER Activates/deactivates the lo w-pass filter for the incoming wa ve f or m data.
14 FUNCTION SETTING Setting for the sub men u display , color system, color of the tally lamp and the picture size . Item T o do Setting value sub menu POSI. Select the contents and displa ying position of “sub menu. ” ☞ “NO TE” COLOR SYSTEM Select the color system.
15 Setting of “CHARA CTER SET . ” Assign a name for each video source . 1 Change the input to one that you want to assign a video source name f or . 2 Select “CHARACTER SET . ” 3 Press buttons to select the first character . • Each time you press button, the character changes as f ollows .
16 External Control 7 About the e xternal control This monitor has three external control terminals. • MAKE/TRIGGER termina l (RJ-45): The f ollowing e xter nal control systems are av ailable .
17 7 Using the MAKE/TRIGGER system The MAKE/TRIGGER terminal is configured as follows . Y ou can assign a function to each pin terminal in “REMO TE SETTING” ( ☞ “PIN1, PIN2, PIN3, PIN4, PIN5” on page 15). • Y ou cannot change the functions assigned to the pin terminals from 6th to 8th.
18 1 Starting the communication: connection command (!00BCN1Cr) 3 Selecting “SDI 1” input (!00BINACr) 5 Te rm inating the communication: termination command (!00BCN0Cr) 6 Monitor’ s status (@00BOKCr) 4 Monitor’ s status (@00BOKCr) 2 Monitor’ s status (@00BOKCr) PC, etc.
19 T roubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the prob lem, unplug the monitor and consult an authorized dealer or ser vice center . Symptom Probable cause and corrective action Pa ge No power supply • T ur n on the switch.
20 7 Self-check pr ogram This monitor has a self-check function, which allo ws it to detect malfunctions and aler t you. This mak es troubleshooting easier . Whene ver a prob lem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, f ollow the steps below and contact y our dealer to resolve the prob lem.
21 • F or easy understanding, pictures and illustrations are shown b y being emphasized, omitted or composed, and may be slightly diff erent from actual products.
22 Specifications (cont.) 100 VESA mounting holes (Size: 4-M4, depth: 10 mm) 100 117 * at the higher position ** at the lower position 7 Dimensions Unit: mm (inch) DT -V24L3D <Front vie w> <Side view> <Rear view> 477 (18 7/8) 354 (14) 394.
DT-V24_20L3D_EN_cover34.indd 1 DT-V24_20L3D_EN_cover34.indd 1 08.5.13 1:44:38 PM 08.5.13 1:44:38 PM.
© 2008 Victor Company of J apan, Limited 0508STH-MW -VP DT -V24L3D/DT -V20L3D MUL TI FORMA T LCD MONIT OR DT-V24_20L3D_EN_cover34.indd 2 DT-V24_20L3D_EN_cover34.
An important point after buying a device JVC DT-V20L3D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC DT-V20L3D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC DT-V20L3D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC DT-V20L3D you will learn all the available features of the product, as well as information on its operation. The information that you get JVC DT-V20L3D will certainly help you make a decision on the purchase.
If you already are a holder of JVC DT-V20L3D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC DT-V20L3D.
However, one of the most important roles played by the user manual is to help in solving problems with JVC DT-V20L3D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC DT-V20L3D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
