Instruction/ maintenance manual of the product Woodstove F 400 Jotul
Go to page of 68
Jøtul F 400 Monterings-. og bruksanvisningen må oppbevares under hele produktets levetid. These instructions must be kept for future r ef erences. W ir empf ehlen Ihnen, die Montage- und Bedienungsanleitung für spätere Zwecke sorgfältig aufzubewahren.
2 USA /Canada Standards The Jøtul F 400 woodstove has been tested and listed to; U.S. Standards: ANSI/UL 737 and ANSI/UL 1482. Canadian Standards: CAN/ULC-S627-M93 T ests performed by : ITS , In ter tek T esting Services , Middleton, WI Manufactured by: Jøtul AS, P .
3 T able of Contents Standards and Safety Notices Standards / Codes ..................................................................... 2 Safety Notices ............................................................................. 3 Installation ...
4 Assembly Before Installation Unpack the Stove Inspect the stove for damage. Contact your dealer immediately if any damage is found. Do not install the stove if any damage is evident.
5 • Brick or modular block must be a minimum of 4” (10 cm) nominal thickness. Stone construction must be at least 12” (30 cm) thick. • A newly-built chimney must conf orm to local codes, or , in their absence, must comply with national regulations.
6 C onnecting to the Chimne y Masonry Chimney When installing a Jøtul F 400 into a masonry chimney through a “ thimble” (the opening through the chimney wall to the flue), the thimble must consist of ceramic tile or steel and be securely cemented in place.
7 Using Shields to Reduce Clearances Chimney Connector Heat Shields: Use only connector heat shielding listed for use with solid fuel heaters. The connector heat shield must begin 1” above the lowest exposed point of the connector pipe and extend vertically a minimum of 25” (640 cm) above the top surface of the stove.
8 Jøtul F 400 W oodstov e Clearances Unprotected Surface P arallel to the W all Protected Surface P arallel to the W all Unprotected Surface Corner Installation Protected Surface Corner Installation .
9 Stove Unprotected Surface Protected Surface Installation Clearances Installation PER N FP A211 OR CAN/ CSA -B365-M93 Side Rear Corner* Side Rear Corner* Stove -no heatshield 19" A 25" B 18.
10 Operation Please read the f ollowing section completely , befor e building a fire in your new Jøtul F 400 . Use Solid W ood Fuel Only First this stove is designed to burn natural wood only . W ood that has been air-dried for a period of 6 to 14 months will provide the cleanest, most efficient heat.
11 the most efficient burn is between 400 ° and 600 ° (204 °C -316°C). See figure 12 for the best locations to place a stove-top thermometer . Never overfire the stove. If any part of the stove or chimney glows, you are overfiring. A house fire or serious damage to the stove or chimney could result.
12 Glass Removal 1 . Remove the door from the stove and place on a flat surface. 2 . Carefully remove all of the glass clips from the inside of the door . 3 . Gently remove the glass panel and gasketing. 4. Using a wire brush, remove all remaining debris from the glass area .
13 W arning: Operate y our Jøtul F 400 with the fro nt door fully open and the firescreen in place or fully closed. A partially opened door may result in overfiring. Also, if the door are left partly open, gas and flame may be drawn out of the stove opening, creating risks from both fire and smoke.
14 25 3/ 4” 23 1/ 4 ” 29 1/2” top exit 25 1/2” rear exit 13” 28 1/2” 26 1/2” Fig. 1 USA /Canada Fig. 2 Fig. 3 Fig. 4.
15 USA/Canada Fig. 8 Fig. 9 Fig. 10 Protection and air space must comply with NF P A 211OR CAN/CSA-B365. Fig. 6 Fig. 5 Fig. 7.
16 USA/Canada Fig. 12 Fig. 13 Fig. 11 Draw . no. 1 -1714.
17 USA /Canada.
18 Parts list for the Jøtul F 400 woodstove Consult your dealer for part numbers and replacement parts. 1 Ashlip 2 Door 2 A Gasket 2 B Glass clips 3 B Latch 4 Right side panel 5 Front panel 6 T op ca.
19.
20 NORSK.
21 NORSK Innhold Forhold til myndighetene T ekniske da ta for Jøtul F 400 ................................................... 21 Sikkerhetsregler ........................................................................... 2 2 Brannforebyggende tiltak .
22 Sikkerhetsregler Advarsel! Man må forsikre seg om at det er nok tilførsel av uteluft til det rommet hvor ildstedet blir installert. Utilstrekkelig luft-tilførsel kan forårsake at røykgasser kommer ut i rommet. Dette er meget farlig! Symptomer på dette kan være tretthet, kvalme og uvelhet.
23 askeskuffen. Denne er merket: Europa . . . . . Sikkerhetsskruen i midten (fig. 6) demonteres, og settes på den nye inspeksjonsluken som er merket Europa. • T opplaten er festet med 2 stk. transportskruer . Disse må fjernes p.g.a. bestemmelser om tilgang til å feie røykrør .
24 Bruksanvisning Første gangs opptenning og daglig bruk Jøtul F 400 er et rentbrennende produkt som ved hjelp av ekstra tilførsel av forbrenningsluft, sørger for en etterbrenning a v skadelige gasser og partikler . Det er viktig at systemet blir brukt riktig.
25 Feiing av røykrør til skorstein Feiing av røykrør kan utføres gjennom feieluken i røykrøret, eller ved å løfte vekk topplaten og feie gjennom produktets røykuttak. K ontroll av ildstedet Jøtul anbefaler at du selv kontrollerer ditt ildsted nøye etter at feiing/ rengjøring er g jennomført .
26 S VENSKA.
27 S VENSKA Myndigheternas bestämmelser Jøtul F 400 är en rentbrinnande produkt som har typgodkännande 0309. Installation av en eldstad måste ske i enlighet med i Sverige gällande bestämmelser .
28 Avstånd från produkten till vägg av brännbart material Till bakre vägg (med konvektionsplåt monterad på produktens baksida): Min. 100 mm Till bakre vägg (utan konvektionsplåt) : Min.
29 På insidan dörrarna sitter det en inspektions-lucka som är festad med 2 st skruvar i ytterkant. Inspektions-luckan skruvas av och ersättes med en tillsvaranda del som ligger i askskoffs-lösningen. Denna är märkt Europa . Säkerhets- skruvan i mitten (fig.
30 Dagligt användande • Öppna dragventilen • Lägg två halvstora vedklabbar ut/in på varje sida i eldstadsbotten. Lägg lite papper , ev . näver fr ån björkv ed, alternativt tändpapper , mellan dessa och lägg finkluven ved ovanpå, lite på kors och tvärs.
31 K ontroll a v eldstaden Jøtul rekommenderar att ägaren själv kontrollerar eldstaden noga efter att sotning/rengörning har genomförts. K ontroller a att alla synliga ytor inte har några sprickbildningar . Se ä ven till att alla fogar är täta sam t att tätningslister ligger på pla ts.
32 T able of contents Relationship to the authorities T echnical data of Jøtul F 400 ................................................ 33 General safety precautions .................................................... 3 3 Measures to prevent fires ...
33 Ensure that the chimney or flue is structurally sound. In particular , it must not be possible for pr oducts of combustion to come into contact with combustible materials in the structure of the building. In some situations it may be advisable to fit a flue liner prior to the installation of the stove.
34 ENGLISH inlet of the stove. From there a flexible hose is conducted out of the house. The installation instruction for this is enclosed with the installation unit. Assembly prior to installation Jøtul F 400 is sold in many countries with varying demands on fireplaces.
35 Operating instructions Initial lighting and daily use Jøtul F 400 is a clean-burning product and with additional supplies of combustion air , it allows f or afterburning of hazardous gases and particles. It is important that the system is used corr ec tly .
36 Sweeping of flue pipes to the chimney It is possible to sweep through the sweeping hatch in the flue pipe or to remove the top plate and sweep through the smoke outlet. Control of the stove Jøtul recommends that you personally control your stove carefully af ter sweeping/ cleaning.
37 T able des matieres Réglementations nationales Fiche technique du modèle Jøtul F 400 ............................. 37 Consignes générales de sécurité .......................................... 3 8 Mesures de prévention des incendies .......
38 Consignes générales de sécurité Distance par rapport à un mur constitué de matériaux inflammables et e xigences relatives à l’ écran pr otec teur au sol : Con tactez l’ autorité locale c ompétente pour vous renseigner sur les réglementations locales et vous assurer que votre installation est sûre et légale.
39 Cendrier (C) Ouvrez la porte en tournant la poignée dans le sens con trair e des aiguilles d’ une montre sur un demi-tour . Utilisez un gant ou autre pour extraire le tiroir à cendres. Attention ! Enlevez les cendres uniquement lorsque le poêle est froid.
40 Ne faites jamais brûler les matériaux suivants dans votre poêle : - déchets ménagers, sacs plastique, etc. - bois peint ou imprégné (fortement toxique) - plaques d’ aggloméré ou de cont re plaqué-bois de récupération Ces matériaux risquent d’ endommag er l’ appareil et de polluer l’ atmosphère.
41 Longueur , quantité et qualité des bûches La longueur maximale des bûches doit être de 50 cm. Les bûches doivent être placées parallèlement à la paroi du fond de la chambre de c ombustion. L ’ appareil Jøtul F 400 possède une capacité nominale de 7 ,0 kWh.
42 Índice de contenido Relación con las autoridades de distintos países Información técnica de la estufa Jøtul F 400 ...................... 43 Medidas para prevención de incendios ................................ 4 3 Instalación de Jøtul F 400 Cimientos .
43 Es necesario asegurarse de que la chimenea o el sistema de salida de humos tan sólo se utilizan con una estufa. Asegúrese de que la chimenea o el conducto de humos tienen una estructura sólida. En par ticular , no debe permitirse que los productos de combustión entren en contacto con los materiales combustibles de la estructura del edificio.
44 ventiladores en las habitaciones donde haya chimeneas porque podrían causar una presión negativa y aspirar gases venenosos dentro de la habitación. Para evitarlo, es posible introducir directamente aire del exterior a la estufa mediante un adaptador (elemento opcional) que se monta en la entrada de aire de la estufa.
45 Instrucciones de funcionamiento Encendido inicial y uso diario Jøtul F 400 es un producto que no deja residuos de combustión y que, con la ayuda del suministro adicional de aire de combustión, permite la combustión retardada de los gases y partículas peligrosas.
46 Asegúrese de que la puerta de la bandeja para ceniza está cerrada firmemente mientras se esté utilizando la estufa. V ea asimismo la descripción donde se explica cómo manipular las cenizas en la sección “Medidas par a prev ención de incendios” .
47 Sustitución de la placa deflectora • Lev ante la placa superior . • La placa deflectora está apoyada sobre los quemadores. • Para retirar la placa deflectora, afloje los soportes que la mantienen sobre los quemadores. Utilice un martillo para golpearlos cuidadosamente hacia las puertas.
48 Indice generale Relazione alle autorità Dati tecnici di Jøtul F 4 00 ......................................................... 48 Misure di sicurezza generali ..................................................... 4 9 Misure preventive antincendio .
49 Misure di sicurezza generali Distanza da pareti di materiale infiammabile e requisiti della piastra sul pavimento: Contattare le autorità locali per informazioni sulle leggi locali e per assicurarsi che la propria installazione sia sicura e a norma.
50 2 . La piastra superiore è fissata con 2 viti per il trasporto. Queste devono essere rimosse in conformità con le disposizioni relative al libero accesso per i tubi di eliminazione del fumo.
51 una maggiore ventilazione nella stanza. Lasciare che il fuoco bruci con un tiraggio elevato fino a che tutte le tracce di gas scompaiono e non sono più presenti fumo e cattivi odori. Prodotti smaltati: Le prime volte che si utilizza un camino nuovo può formarsi sulla superficie del camino acqua di condensa.
52 Controllo del camino Jøtul consiglia di controllare personalmente e con attenzione il camino dopo averne eseguito la pulizia. Controllare che non vi siano crepe su tutte le aree di superficie visibili. V erificare che tutte le giunzioni siano ermetiche e che le guarnizioni siano posizionate correttamente.
53 Inhalt Behördliche Auflagen T echnische Daten des Jøtul F 400 .......................................... 54 Allgemeine Sicherheitsbestimmungen ................................ 5 4 Brandverhütungsmaßnahmen .......................................
54 T echnische Daten des Jøtul F 400 : Mate rial: Gußeisen Anstrich: Sc hw ar ze F arbe, Emaille Heizmaterial: Holz Max. Holzscheitlänge: 50 c m Abzugssystem: Ob erer Lufteinzug und Entfachungsbelüftung V erbrennungssystem: Sek undäre V erbrennung Rohrstutzen: Oben/Rückseite Rohrabmessungen: Durchmesser 150 mm Gewicht: C a .
55 der am Lufteinlaß des Ofens angebracht wird, direkt Außenluf t zug eführt werden. V on dor t führ t ein flexibler Schlauch nach Außen. Die Anleitung zur Aufstellung sind der Zusatzausstattung beigelegt. Zusammenbau vor der Aufstellung Jøtul F 400 wird in vielen Ländern verkauft, die unterschiedliche Anforderungen an Öfen stellen.
56 Inbetriebnahme Inbetriebnahme und täglicher Gebrauch Der Jøtul F 400 ist ein sauber brennender Kamin, der mit Hilfe einer zusätzlichen V erbrennungsluftzufuhr alle giftigen Gase und Partikel nachverbrennt. Eine ordnungsgemäße Benutzung des Systems ist wichtig.
57 P flege Reinigung des Sichtfensters Der Jøtul F 400 ist mit einem Luftspülungssystem ausgestattet. Durch die Luftzufuhröffnung gelangt die angesaugte Luft von oben an die Feuerstelle und reinigt das Sichtfenster entlang der Innenseite nach unten.
58 Brennholz guter Qualität sind beispielsweise Scheite von Birken-, Buchen- und Eichenbäumen. Die Energieausbeute von 1 kg Holz schwankt nur wenig. Dagegen schwankt das spezifisches Gewicht (T rockengewicht) der v erschiedenen Holzarten erheblich. Ein bestimmtes V olumen Birkenholz lief ert z.
59 Inhoudsopgave W ettelijke voorschrif ten T echnische gegevens v an de Jøtul F 4 00 ............................. 60 Algemene veilighei dsmaatregelen ........................................ 6 0 Maatregelen voor brandpreventie .....................
60 T echnische gegevens v an de Jøtul F 400 : Materiaal: Gietijzer Afwerking: Zwarte/Email Brandstof: Hout Max. lengte van blokken: 50 c m Ontluchtingssysteem: Bovenste en onderste roosters V erbrandingssysteem: Secundaire verbranding.
61 door een soortgelijk onderdeel dat zich in de aslade bevindt. V er wijder de veiligheidsschroef ( afb. 6) in het midden en bevestig deze op de nieuwe inspectieplaat met de aanduiding Europa. Opmerking! De ring moet aan de buitenkant worden geplaatst.
62 NEDERLANDS Geverfde haarden: W anneer u de haard v oor het eerst gebruikt, kan irriterend gas vrijkomen, dat onaangenaam kan ruiken. Dit gas is niet giftig, maar het is het beter om een raam of een deur in de ruimte te openen om te zorgen voor extra ventilatie.
63 of de deur- en glasafdichtingen luchtdicht afsluiten en of de pakkingen nog op hun plaats zitten. Pakkingen die sporen van slijtage of vervorming vertonen, moeten worden vervangen. Maak de pakkingsgroeven grondig schoon, breng keramische lijm aan (te verkrijgen bij uw Jøtul-dealer) en druk de pakking goed in de groef .
64.
65 B C A A Fig. 2a Fig. 2b Fig. 3 Fig. 4 Fig. 5 Fig. 6 A A Fig. 7.
.
.
Jøtul arbeider kon tinuerlig for om mulig å f orbedre sine produkter , og vi f orbeholder oss rett til å endre spesifikasjoner , farger og utstyr uten nærmer e kunngjøring .
An important point after buying a device Jotul Woodstove F 400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jotul Woodstove F 400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jotul Woodstove F 400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jotul Woodstove F 400 you will learn all the available features of the product, as well as information on its operation. The information that you get Jotul Woodstove F 400 will certainly help you make a decision on the purchase.
If you already are a holder of Jotul Woodstove F 400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jotul Woodstove F 400.
However, one of the most important roles played by the user manual is to help in solving problems with Jotul Woodstove F 400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jotul Woodstove F 400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
