Instruction/ maintenance manual of the product ET-3402-J John Deere
Go to page of 20
7 1/4 Inch Circular Saw Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE CIRCULAR SAW AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.
2 7 1/4 Inch Circular Saw Operator's Manual Congratulations on the purchase of your new Circular Saw! You can be assured your circular saw was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance.
7 1/4 Inch Circular Saw Operator's Manual 3 T able of Content SAFETY .................................................................................................................. 4-11 GENERAL SAFETY RULES ....................................
4 7 1/4 Inch Circular Saw Operator's Manual W ARNI N G W A R N I NG SI N T HE M A NUA LS . W A RN I NG SI N T HE M A NUA LS . CA U T I ON OC A UT I ON S IN O T H E M A N UA L S OC AUT I ON S IN O.
7 1/4 Inch Circular Saw Operator's Manual 5 KEEP WORK AREA CLEAN AND WELL LIT. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. Don't expose power tools to rain. Don't use power tools in damp or wet locations.
6 7 1/4 Inch Circular Saw Operator's Manual DON'T OVERREACH Keep proper footing and balance at all times. MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories.
7 1/4 Inch Circular Saw Operator's Manual 7 OUTDOOR USE EXTENSION CORDS When tool is used outdoors, use only extension cords intended for use outdoors and so marked. STAY ALERT Watch what you are doing. Use common sense. Do not operate tool when you are tired.
8 7 1/4 Inch Circular Saw Operator's Manual CAUTION ALWAYS KEEP THE MOTOR AIR VENT FULLY OPENED A constantly open motor air vent is necessary to allow air to come in and out for cooling the motor. Do not allow it to become clogged up, even if dust is blown through it.
7 1/4 Inch Circular Saw Operator's Manual 9 CAUTION SUPPORT LARGE PANELS Large panels must be supported as shown in Fig. 1 to minimize the risk of blade pinching and kickback. When cutting operation requires the resting of saw on the work piece, the saw shall be rested on the larger portion and the smaller piece cut off.
10 7 1/4 Inch Circular Saw Operator's Manual LOWER GUARDS Raise lower guard with the retracting handle (Lever). ADJUSTMENTS Before cutting be sure depth and bevel adjustments are tight. USE ONLY CORRECT BLADES IN MOUNTING Do not use blades with incorrect size holes.
7 1/4 Inch Circular Saw Operator's Manual 11 EXTENSION CORD Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
12 7 1/4 Inch Circular Saw Operator's Manual Functional Description MODEL: ET-3402-J CIRCULAR SAW NAME OF PARTS: (Fig. 3) NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool.
7 1/4 Inch Circular Saw Operator's Manual 13 Operation APPLICATIONS: Cutting various types of wood. PRE-OPERATION: Before using the Electric Power Tool, complete the following preparations: 1. Power source: Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate.
14 7 1/4 Inch Circular Saw Operator's Manual Operation OPERATION: CUTTING PROCEDURES: CAUTION: RECHECK THAT THE SAW BLADE IS SECURELY CLAMPED. CONFIRM THAT THE CLAMP LEVER FOR ADJUSTING THE SLOT DEPTH, THE WING-BOLT FOR ADJUSTING THE ANGLE OF INCLINATION.
7 1/4 Inch Circular Saw Operator's Manual 15 Operation POCKET CUTTING: CAUTIONS: RELEASE TRIGGER AFTER CUTTING WORK AND DISCON- NECT PLUG FROM POWER SUPPLY BEFORE ANY ADJUST- MENT. NEVER TIE OR WEDGE THE SAFETY COVER IN A RAISED POSITION. OPERATION (CONTINUED): 1.
16 7 1/4 Inch Circular Saw Operator's Manual Operation MOUNTING AND DISMOUNTING THE SAW BLADE: CAUTION: TO AVOID SERIOUS ACCIDENT, ENSURE THE SWITCH IS IN THE OFF POSITION, AND THE POWER SOURCE IS DISCON- NECTED. 1. Dismounting the saw blade (Fig.
7 1/4 Inch Circular Saw Operator's Manual 17 Maintenance and Inspection MAINTENANCE AND INSPECTION: CAUTION: BE SURE TO SWITCH POWER OFF AND DISCONNECT THE PLUG DURING MAINTENANCE AND INSPECTION.
18 7 1/4 Inch Circular Saw Operator's Manual STANDARD ACCESSORIES: CAUTION: RECOMMENDED ACCESSORIES FOR THE ELECTRIC POWER TOOL ARE MENTIONED IN THIS MANUAL. THE USE OF ANY OTHER ATTACHMENT OR ACCESSORY IS HAZARDOUS. 1. Saw Blade 1 2. Wrench 1 3.
7 1/4 Inch Circular Saw Operator's Manual 19 Notes.
20 7 1/4 Inch Circular Saw Operator's Manual Manufactured for Deere & Company, Moline, Illinois 61265 7 1/4-Inch Circular Saw Operator's Manual 111 Code No.
An important point after buying a device John Deere ET-3402-J (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought John Deere ET-3402-J yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data John Deere ET-3402-J - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, John Deere ET-3402-J you will learn all the available features of the product, as well as information on its operation. The information that you get John Deere ET-3402-J will certainly help you make a decision on the purchase.
If you already are a holder of John Deere ET-3402-J, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime John Deere ET-3402-J.
However, one of the most important roles played by the user manual is to help in solving problems with John Deere ET-3402-J. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device John Deere ET-3402-J along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center