Instruction/ maintenance manual of the product XACTA Jet Tools
Go to page of 16
Owner's Manual XACTA ® Fence II Commercial 30/50 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708950Z Ph.: 800-274-6848 Revision H 03/06 www.
2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service.
3 Table of Contents WARRANTY A ND SERVICE ........................................................................................................... ............. 2 Table of Contents ...................................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Rea d and understand the warnings posted on the mach ine and in this manual. Failure to comply with all of these warnings may cause seri ous injury.
5 21. Keep visitors a safe distance from the work area. Keep children away. 22. Make your workshop child proof with padlocks , master switch es or by removing starter keys. 23. Give your work undivided attention. Looking a r ound, carrying on a conversation and “horse-p lay” are careless acts that can result in serious inj ury.
6 Unpacking Open shipping carton s and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manu al thoroughly for assembly, alignment, and ma intenance instructions.
7 Installation Tools required 7/16" and 1/2" wrenches Cross point screwd river 3/16" hex wrench Adjustable square Hammer (or rubber mallet) Straight edge The following instructions are for in stalling the XACTA Fence II and Rail System on JET Models JTAS-10 and JTAS-12 series ta ble saws.
8 Back Rail Installation 1. Locate the back rail which is 2" x 2" with holes running along one side onl y. The height of the back rail when attached to the saw is not critical. 2. Align the holes in the back rail to the holes in the table top, as shown in Figure 4.
9 Wooden Extension Table The wooden extension table is an optional accessory. Tools required Electric drill Cross point screwd river 7/16" and 1/2" wrenches Four clamps Straight edge Hammer .
10 as shown in Figure 10. Finger tighten only. 5. Install three 1/4-20 x 1-1/2 hex cap screws, three 1/4 flat washers, and three 1/4 nuts into the holes in the rear edge of extension table as shown in Figure 11. Finger-tighten only. 6. Re-check the table for alignment, make further adjustments if necessary, then tighten all screws and nuts.
11 XACTA Fence Screw the lock lever knob into the threaded handle on the XACTA Fence II as shown in Figure 14. The lock lever has three function al positions as shown in Figure 15: • The upright position permits mountin g and removal of fence from the saw.
12 Adjusting Fence Parallel to the Miter Slot 1. Place the fence next to the outside edge of the right miter slot and lock it. 2. The fence should be even with the miter slot from front to back. 3. If the fence is not even along the length of the miter slot, unlock the fence, remove it and turn upside down.
13 Parts for the XACTA Fence II Commercial 30/50 Index No. Part No. Description Size Qty 1 ............... XF2-101 ................... Left Side Plate ...................................................... ................ .................... 1 2 ...
14 Parts for the XACTA Fence II Rail Assembly Index No. Part No. Description Size Qty 1 ............... XF2-201 ................... Front Rail (50”) ..................................................... ................ .................... 1 ......
15 Parts for the XACTA Fence II Leg Assembly Index No. Part No. Description Size Qty 1 ............... XF2-301 ................... Leg ....................................................................... .................................... 2 2 ...
16 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m.
An important point after buying a device Jet Tools XACTA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet Tools XACTA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet Tools XACTA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet Tools XACTA you will learn all the available features of the product, as well as information on its operation. The information that you get Jet Tools XACTA will certainly help you make a decision on the purchase.
If you already are a holder of Jet Tools XACTA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet Tools XACTA.
However, one of the most important roles played by the user manual is to help in solving problems with Jet Tools XACTA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet Tools XACTA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
