Instruction/ maintenance manual of the product JWTS-10 Jet Tools
Go to page of 40
Opera ting Instructions and Parts M anual Table Sa w Model : JW TS -10 WMH T OOL G ROUP 2420 Vantage Dr iv e El g in, I llinoi s 60124 Part No . M - 708100 Ph.
2 W A RR A N TY A N D SERVI CE W M H Too l G rou p, I nc ., warrants e very product it se lls. If one of ou r to ols nee ds service or re pai r, one of our Authorize d S e rvi ce Cente r s located throughou t t he Unit e d States can give you quick se rvi ce .
3 Ta ble of Contents Tab l e o f Con tents .................................................................................................................................... 3 Warn ings ...............................................................
4 W a r nings 1. Read and under st and t he enti r e owners manual befor e at tempti ng as sem bly or operat i on. 2. Read and understand t he w ar ning s po sted on the m achine and i n thi s m anual. Fail ure t o co m ply w i t h all of t hes e warning s m ay c ause seri ou s inj ur y.
5 Error! Objects cannot be created from editing fi e l d cod es. 21. Pr ov i de f o r adequat e space s ur r oun di ng work area and non-gl ar e, o v erhead li gh t ing. 22. Keep t he f l oor around t he m achine clean and free of s crap m ater ial, oil and grease.
6 The most co mmo n acciden ts among tabl e saw users, accordi ng to stat istics, can be l inked to k i ckback, t he h igh- s p eed expulsio n of material f rom the tabl e that can st rike the op erator. Kickb ack ca n al s o result in operato r’ s h and s b ein g pu ll ed i nt o th e b l a d e.
7 Features Speci ficat ions Model Nu m ber ............................................................................................................................ J W T S-10 Stoc k Nu m ber ........................................................
8 Def initions A nd T erminolog y A rbor: Metal shaf t that connect s the driv e m echan ism to the blade. Bevel Edg e Cut: Tilt of t he saw arbor and blade between 0° and 45° t o per f orm an angl ed cutt ing operati on. Blad e Guard: M echanis m m ounted ov er t he saw blade t o pre v ent acc i dental cont ac t w i th the cutti ng edge.
9 Shippi ng Content s Carton Contents 1 ea Tabl e Saw (not show n) 1 ea Fr ont Ra i l – Long (A) 1 ea Fr ont Ra i l – Short (B) 1 ea Ext ens i on Wing – Left ( C) 1 ea Ext ens i on Wing – Righ.
10 Hard wa re The shi pping cart on incl udes two hard ware bag s with par ts for as sem bli ng the J W TS-10 Tabl e Saw. Hardware ba g J W TS 10-HP contai ns si x pack ets of parts and JW T S10-SHP contai ns three packet s of parts.
11 A ssem bly Read an d u n derstand al l assembl y inst ructions bef ore attemp t i ng assembl y! F ailure to co m p ly may cause se r ious in jur y ! Un packing an d Cleanu p 1.
12 A ssembling th e Saw to the S tand Do not pl ug t he ta ble sa w into th e p ow er source unti l all assembl y h as been comp leted! F ai l ure to comply may cau se se r ious in jur y ! 1.
13 Handwh eels Ref erring to Figur e 6: The JW TS-10 Tabl e Saw c om es equipped with t wo handwheel s which l ook i dentic al exc ept f or t he m ounti ng holes as f oll ow s: 1.
14 Front Gu id e Rail Ref erring to Figur e 9: Requir ed Fasteni ng Har dware (see also i nset) : A – 6 ea – Square Head Bolt ( M8) B – 6 ea – Lock W asher ( M 8) C – 6 ea – Hex Nuts (M8) Requir ed Tool s: – 12mm wrench 1.
15 Switch Bracket Ref erring to Figur e 11: 1. Insert tw o M 6x12 pan head screws ( A) t hrough the back of the switc h bracket m ounting hol es (B). Place M6 washers (C) and square nut s (D) on the t hr eaded ends of the screws.
16 I nstallin g /Replacin g th e Blade When in stalli ng or ch angin g the saw b lade, alw ays disconnect t he saw fro m the pow er source! F ailure to comply cay cau se se r ious in jur y ! 1.
17 Table In sert Ref erring to Figur e 16: 1. Raise t he bl ade guard ass em bly. 2. Lower the bl ade complet e l y. 3. Pl ace t he table insert (A) int o the openi ng w i th the notched end (B) tow ards the spl itter (C ).
18 Thi s f ence i s posit ioned by lif ting up the loc k handle (A, F ig. 19) and slidi ng t o the desir ed l ocation. "Fi ne-tuni ng" is accom plished by pus hing the mi cro-adjust knob in (B, Fig. 19) and at t he s am e time turn ing it ( C, Fi g.
19 Grounding Instructions 1. All Gr ounded, Cord-connect ed Tool s: In t he e v ent o f a m alfunc t i on or break dow n, groundi ng prov i des a path of least resi stance f or elec tric current to reduce the ri s k of e l ectri c shock.
20 A d j ustments Blade Raisin g and T il t Mechan ism Never try to force the til tin g mechan ism past the 45º or 90º stops! This may cause the b lade to g o out o f a li gnment! Ref erring to Figu.
21 Operations Table Saws Famili arize y ours elf wit h t he locati on and operati on of all c ont ro l s and adj ustm ents and the use of ac ces sori es such as the mi ter gauge and ri p f ence .
22 Rip Sawing Rippi ng is w here t he w or k piece i s f ed with t he grai n int o the sa w bl ade using the f ence as a guide and a posi ti on i ng de v ic e t o ens ur e the desired widt h of cut (Figur e 27) . Figur e 27 Before st artin g a rip ping cut, be su re t h e fence is clamp e d securely and alig ned pro perly .
23 W hen r ipping l ong boards, use a support at the front o f the tabl e, such as a r oll er stand, and a support or "tailm an" a t t he rear as s hown i n Fi gure 30. Nev er use the rip fenc e beyond t he point where the car r i age is fl ush with t he end o f the rails.
24 To im prove t he effectiv enes s of the mi ter gauge in c ross cut ti ng, some users m ount an aux ili ary wooden ex tension f ace (w i th a g l ued-on stri p o f sandpaper) to the m it er gauge as s ho w n i n Fi gure 34.
25 Dado Cutting – Dadoi ng i s cutt ing a wide groov e i nto a workpi ece or cutting a r abbet along t he edge o f a w or kpiece. A dado insert, shown in F igure 38, i s neces s ary for th i s type of operati on.
26 Filler Piece A fil ler piece (Figur e 40) i s nec es sary f or narr ow ri pping and permi t s the blade guar d t o re m ain on the m achine. It a l so pro v ides space f or the saf e use of a push sti ck.
27 M a intenance Always d isc onnec t powe r to t he ma chine before pe rform ing ma inte nanc e. Fai lure to do th is ma y res ult i n ser ious per sona l in jury . Clean ing Clean t he JWTS- 10 according to t he s chedul e below to ensure m a x im u m per f orm ance .
28 Tr oubleshoot ing Sympt om Po ssible Cause Correcti on Low vol tage. Check power line for proper vo l tage. Motor wi l l n ot start Open circuit in motor or loose connecti o n . Inspect all lead connections on motor f or loose or open connections. Short circuit in line cord or plug.
29 Part s JWTS-10 Table and C abinet Parts Lis t Index No. Part No . Descrip t ion Siz e Qty 1 ............... JWTS1 0-3 01 ........... Tab le ................................................................. ................................... 1 2 ..
30 JWTS-10 Table and C abinet Explo ded V iew.
31 Mot or a nd T runnio n A ssembly Parts List Index No. Part No . Descrip t ion Siz e Qty 1 ............... VB-A3 1 ................... Belt .................................................................... A-3 1 ........................... 1 2 ..
32 Mot or a nd T runnio n A ssembly Parts List Index No. Part No . Descrip t ion Siz e Qty 55 ............. JWTS1 0-1 55 ........... W a ve W as he r .................................................... WW - 16 ....................... 1 56 ...........
33 Mot or a nd T runnio n A ssembly Exploded V i ew.
34 Fence an d Rail Par ts List Index No. Part No . Descrip t ion Siz e Qty ................. JWTS1 0-FA ............ Fence Ass embly (#1 th ru #39) ........................... ................................... 1 1 ............... JWTS1 0-2 01 ......
35 Fence an d Rail Par ts List Index No. Part No . Descrip t ion Siz e Qty 53 ............. JWTS1 0-25 3 ........... Re ar Ra i l, Long .................................................. ................................... 1 54 ............. TS- 1550041 .
36 Stan d Assem bly Par ts List and Ex pl ode d View Index No. Part No . Descrip t ion Siz e Qty 1 ............... TS- 1540061 ............ He x N u t 1 * * ......................................................... M8 ............................ 28 2 .
37 Wiring D iagram 200MF D 250 VAC 200MF D 250 VAC WHITE BLA CK BLA CK WHITE GREEN GRE EN 30MFD 350 VAC ELEC T R IC AL SC HE MAT IC - 115V RED YELLOW BLACK WHIT E BLA CK WHITE GRE EN GREEN ELEC T R IC.
38 Order ing Replacemen t Parts To or der par t s or reac h our servi ce departm ent, c all 1-800-274-6848 bet w een 7: 30am and 5: 30pm ( CS T ), Monday t hrough Fri day. Ha v ing t he Model Nu m ber and Seri al Nu m ber of y our m achine avail able when you call w il l allow us to ser v e you quickly and ac curately.
39 Notes.
40 WM H Tool Gr ou p 2420 Van t age Drive Elgin, Il linois 60124 Phone : 800 - 274-6848 www.wm htoolgr oup.com.
An important point after buying a device Jet Tools JWTS-10 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet Tools JWTS-10 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet Tools JWTS-10 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet Tools JWTS-10 you will learn all the available features of the product, as well as information on its operation. The information that you get Jet Tools JWTS-10 will certainly help you make a decision on the purchase.
If you already are a holder of Jet Tools JWTS-10, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet Tools JWTS-10.
However, one of the most important roles played by the user manual is to help in solving problems with Jet Tools JWTS-10. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet Tools JWTS-10 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
