Instruction/ maintenance manual of the product JWCS-10 Jet Tools
Go to page of 16
Owner's Manual XACTA ® Fence II Homeshop 30/52 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708928Z Ph.: 800-274-6848 Revision B 03/06 www.
2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service.
3 Table of Contents WARRANTY A ND SERVICE ........................................................................................................... ............. 2 Table of Contents ...................................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Rea d and understand the warnings posted on the mach ine and in this manual. Failure to comply with all of these warnings may cause seri ous injury.
5 21. Keep visitors a safe distance from the work area. Keep children away. 22. Make your workshop child proof with padlocks , master switch es or by removing starter keys. 23. Give your work undivided attention. Looking a r ound, carrying on a conversation and “horse-p lay” are careless acts that can result in serious inj ury.
6 Unpacking Open shipping carton s and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manu al thoroughly for assembly, alignment, and ma intenance instructions.
7 Installation Tools required Drill with 5/16" drill bit 10mm open end wrenches Cross point screwd river Adjustable square Hammer (or rubber mallet) Straight edge The following instructions are for in stalling the XACTA Fence II and Rail System on JET Models JWCS-10 and JWTS-10 series table saws.
8 Back Rail Installation 1. Locate the back rail which is 1-1/2" x 1-1/2" with holes running along one si de only. The height of the back rail when atta ched to the saw is not critical. 2. Align the holes in the back rail to the holes in the table top, as shown in Figure 4.
9 3. Tap down the extension table at various points along its edge where it meets the saw table, until it is level with the saw table (Figure 7). As one part of the edge becomes level with the table, tighten the clamp on that side. Then move to the other side and re peat, until the full length of the edge is level with the saw table.
10 Guide Tube Referring to Figure 11: The guide tube (A) is placed on to p of the front rail (B) and is mounted with t he scale facing toward the operator. 1. Align the holes in the bottom of the guide tube (A) with the holes in the front rail (B). 2.
11 Fence Adjustments Note: Fence adjustments should be perform ed in the order given. Leveling Fence to the Saw Table 1. Place the fence on the table and lock it. 2. View the fence from the left side of the saw (Figure 14). Look for the spa ce between the table and the fence bottom to be equal along the entire length of the fence (A, B, Fig.
12 90 ° to the Table Adjustment 1. Place the fence on the saw table and lock it. 2. Place a square (A, Fig. 17) on the table next to the fence. The fence should b e 90 ° to the table. 3. If adjustment is necessary, unlock the fence, and turn one of the two nylon adjustment screws (B, Fig.
13 Parts Ordering Replacement Parts To order parts or reach our se rvice department, call 1-800 -274-6848 between 7:30 a.m. and 5:30 p.m. (CST), Monday through F riday. Having the Model Number and S erial Number o f your machine available when you call will allow us to serve you quickly and accurately.
14 Parts for XACTA Fence II Homeshop 30/52 Rail Assembly Index No. Part No. Description Size Qty 1 ............... HF2-201 ................... Front Fence Rail - Standard................................. ......................... ........... 1 .......
15 Parts for the XACTA Fence II Homeshop 30/52 Leg Assembly Index No. Part No. Description Size Qty 1 ............... XF2-301 ................... Leg ....................................................................... .............................
16 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m.
An important point after buying a device Jet Tools JWCS-10 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet Tools JWCS-10 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet Tools JWCS-10 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet Tools JWCS-10 you will learn all the available features of the product, as well as information on its operation. The information that you get Jet Tools JWCS-10 will certainly help you make a decision on the purchase.
If you already are a holder of Jet Tools JWCS-10, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet Tools JWCS-10.
However, one of the most important roles played by the user manual is to help in solving problems with Jet Tools JWCS-10. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet Tools JWCS-10 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
