Instruction/ maintenance manual of the product JTS-315SP Jet Tools
Go to page of 9
JTS - 315SP Construction Saw Original: GB Operating Instructions Translations: D Gebrauchsanleitung F Mode d´emploi Walter Meier (Fertigung) AG Bahnstrasse 24 8603 Schwerzenbach Switzerland Phone +41 44 806 47 48 Fax +41 44 806 47 58 jetinfo.eu@waltermeier.
CE - Conformity Declaration Product: Circular Saw Bench JTS - 315SP St ock Number: 10000910SM, 10000910ST , 10000914M Brand: JET Manufacturer: Walter Meier (Fertigung) AG, Bahnstrasse 24, 8603 Schwerz.
3 GB - ENGLISH Operating Instructions Dear Customer, Many thanks for the confidence you have shown in us with the purchase of your new JET - machine. This manual has been prepared for the owner and operators of a JET J TS - 315 SP table saw to promote safety duri ng installation, operation and maintenance procedures.
4 existence of the safety appliances before you start th e machine. Do not attempt operation in this case, protect the machine by unplugging the mains cord. Remove all loose clothing and confine long hair. Before operating the machine, remove tie, rings, watches, other jewellery, and roll up sleeves above the el bows.
5 Always unwind any extension cords fully. Have a damaged or worn cord replaced immediately. Do not use the machine when the ON - OFF switch d oes not operate correctly. The use of accessories other than those recommended in this manual can create a safety hazard.
6 immediately. Do not operate the machine! Dispose of the packing in an environmentally friendly manner. Clean all rust protected surfaces with a mild solvent.
7 Fig 10 Install wheels : Attach the wheels (X, Fig 11) with 4 bolts and nuts. F F ig 11 Install sliding table: Mount the sliding table guide profile with the supplied L - brackets (Fig 12) Fig 12 Install the sliding tabl e.
8 operating manual) (on the last pages of this operating manual) A.1.: Ripping A.2.: Ripping of n arrow stock A.3.: Crosscutting on rip fence A.4 .: Mitre cutting A.
9 Fig 20 Start the machine with care. 7. 6 Adjusting 90°stop The positive stop is adjusted at t he factory. If out of alignment: Disconnect saw from the power source, unplug. Readjust the positive 90° stop. 7. 7 Adjusting sawblade parallel The sawblade is adjusted parallel to the machine table at the factory.
An important point after buying a device Jet Tools JTS-315SP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet Tools JTS-315SP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet Tools JTS-315SP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet Tools JTS-315SP you will learn all the available features of the product, as well as information on its operation. The information that you get Jet Tools JTS-315SP will certainly help you make a decision on the purchase.
If you already are a holder of Jet Tools JTS-315SP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet Tools JTS-315SP.
However, one of the most important roles played by the user manual is to help in solving problems with Jet Tools JTS-315SP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet Tools JTS-315SP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
