Instruction/ maintenance manual of the product HVBS-56M Jet Tools
Go to page of 17
OW NER'S M A NU A L HVBS-56M Horizont al/Vertical Bandsa w JET EQU I P MEN T & TOOLS, I NC . P.O. BO X 134 9 Phone : 253-351-6000 A W MH C ompany Auburn, WA 98071-1349 Fax: 1- 800-2 74- 6 840 www.
2 Important Information 1-YE AR J ET off e rs a on e -yea r limite d LIM ITED WA RRA NTY warranty on this product R EP LA C EM EN T P A R TS Replac em en t parts f or this tool are a v ail abl e dir ectly fr om JET Equipment & T ools. To pl ace an order, call 1- 800-274-6848.
3 WARNING Read an d understan d the enti re instructio n manual bef ore op erating mach ine. Thi s mach ine is d es i gned and intended fo r use b y pro perl y train ed and experi enced personnel only.
4 Speci fi cati ons: H VBS- 56M Stoc k Nu mber................................................................................................................................ 414458 Hori zontal Capac ity: Round @ 90 ° ................................
5 U npacki ng and C lean- U p Note: Read and under stand the enti re manual bef ore attem pting setup or operati on. 1. Rem o v e all cont ents f orm the shippi ng cart on. 2. Inspect cont ents f or shippi ng damage and report any dam age t o your di stribut or.
6 5. Att ach a cross brace to t he opposite end of the bed usi ng three 5/ 16”x1” hex cap bolt s, six 5/ 16” fl at w asher s, and secure wit h thr ee 5/16” hex nut s. Ti ghten t he nut on the end of t he bed fi rst foll owed by the nuts on t he sides.
7 11. Sli de pull ey c o v er ( A, Fi g. 5) ar ound m otor shaft and w orm gear shaf t. Secure wit h tw o hex c ap s c rews and washer s (B, Fig. 5). 12. Lif t m otor with one hand whi le the ot her hand plac es V-belt (C, Fi g.5) on bot h pulley s. 13.
8 4. Rem o v e two screw s (D, Fig. 7) and plat e (E, Fig . 7). 5. Gui de blade t hrough sl ot in tabl e (A, Fi g. 8) and fasten tab le with tw o screws (B, Fig. 8). 6. Fasten support br acket t o underside of t able using scre w (C, Fig. 8) and he x nut.
9 Changing Blade Speed 1. Disco nnect the mach ine from the power sou rce. 2. Pl ace saw arm i n the horizont al posit ion. 3. Loosen tensi oning pl at e he x nut (A, Fi g.10). 4. Open pull ey cov er (B, Fig. 10) . Lif t mot or with one hand whil e pl acing t he belt (C, Fi g.
1 0 Changing Blades 1. Disco nnect machin e f r o m the power sou rce. 2. Raise the saw arm t o the v er tical positi on and loc k in place wit h lock l e v er. 3. Open bl ade cover by r e m ov ing the sm all knob found on t he topsi de o f t he bow. 4.
1 1 A dj usting Blade Tracking WA RNING Blad e tracking adjust ment requires ru nning th e saw with the back cover op en! Thi s adj ustment must be co m p let e d b y qualifi ed per sons only ! Fai lure to co m p ly may cause seri ous injury! Bl ade tracki ng has been set at t he f actory and should not need adj ustm ent.
1 2 Adjusting Automat ic Shut-Off The saw should stop af t er the cut has been com pleted: • If the saw com plet es the cut and conti nues to run, ad j ust the stop ti p (A, Fig. 17) down. • If the saw shuts off be f ore the c ut is com plete, adj ust the stop t ip (A, Fi g.
1 3 Breakdown for Bow As semb ly.
1 4 Breakdown for Base A s sembly.
1 5 Parts Li st for th e HVB S-56M Band saw Inde x Par t No. No . Descrip tion Siz e Qty. 1 .......... TS- 0051031 .............................. He x C ap Bo lt ......................................... 5/1 6”x3/4” ................... 4 2 .......
1 6 Inde x Par t No. No . Descrip tion Siz e Qty. 52 ........ TS- 0081071 .............................. Hex C ap Bo lt ......................................... 5/1 6”x1- 1/2” ................ 1 53 ........ TS- 0091071 ...........................
1 7 Inde x Par t No. No . Descrip tion Siz e Qty. 99 ........ HVBS 462-099 ........................... Spa cer .................................................. ................................... 1 10 0 ...... HVBS 462-100 ..........................
An important point after buying a device Jet Tools HVBS-56M (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet Tools HVBS-56M yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet Tools HVBS-56M - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet Tools HVBS-56M you will learn all the available features of the product, as well as information on its operation. The information that you get Jet Tools HVBS-56M will certainly help you make a decision on the purchase.
If you already are a holder of Jet Tools HVBS-56M, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet Tools HVBS-56M.
However, one of the most important roles played by the user manual is to help in solving problems with Jet Tools HVBS-56M. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet Tools HVBS-56M along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
