Instruction/ maintenance manual of the product DC2 Amtrol
Go to page of 8
1 West Warwick, Rhode Island 02893 INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Yo ur DC 2 D IG IT AL CO NT RO L h as be en ca re fu ll y a ss em bl ed an d f ac to ry te st ed . T o e nj oy th e fu ll ser vi ce thi s un it can pro vi de , y ou sho ul d re ad and fol lo w al l of th e in st ru ct io ns in th is manual.
2 ELECTRICAL CONNECTION ELECTROCUTION HAZARD. FIRST DISCONNECT ALL ELECTRICAL POWER BEFORE SERVICING. ELECTROCUTION HAZARD. THE DC2 MUST BE ELECTRICALLY GROUNDED. NOTE: The DC 2 wi ll opera te on 11 5 VA C & 230 VAC system s. Its ambien t air te mpe rat ure rating is 122°F / 50°C.
3 4. Loosen the screw on the cover of the controller and remove the plastic cover, exposing the wiring pigtails. (When reassembling cover, do not over-tighten screw.) 5. The wire conduit hub is to be connected to the conduit before the hub is connected to the enclosure.
4 START UP BEF ORE CO NTI NUI NG, CH ECK FO R O PEN DR AIN VA LVE S O R OTHER SOURCES OF FLOODING BEFORE STARTING UNIT. 1. Prime pump if necessary and adjust tank precharge to manufacturer’s recommen da tio n for intended pressure range. The factory DC2 setting is 40 psi cut-in and 60 psi cut-out.
5 TROUBLESHOOTING Error Code Reason Action Solution Problem Cause Solution To reset switch at any time: Press 5 6 buttons simultaneously for 5 seconds. * Unit will monitor voltage until voltage condition returns to normal. Pump will restart automatically.
6 GENERAL SAFETY INFORMATION READ CAREFULLY THE PRODUCT INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS. FAILURE TO FOLLOW THE IN STR UC TI ONS A ND WA RNI NG S IN TH E MAN UAL MA Y RES UL T IN SE RIO US OR FA TA L INJURY AND/OR PROPERTY DAMAGE, AND WILL VOID THE PRODUCT WARRANTY.
7 DANGER! EXPLOSION HAZARD. When the well tank has been in service and a change to a higher pre-charge pressure is necessary due to a required change in the pressure switch setting, failure to follow instructions below can cause a rupture or explosion, possibly causing serious or fatal personal injury and/or property damage.
Products covered: all Products manufactured by AMTROL Inc. (“AMTROL”). This warranty cannot be transferred – it is extended only to the original Purchaser or First User of the Product. By accepting and keeping this Product you agree to all of the warranty terms and limitations of liability described belo w.
An important point after buying a device Amtrol DC2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Amtrol DC2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Amtrol DC2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Amtrol DC2 you will learn all the available features of the product, as well as information on its operation. The information that you get Amtrol DC2 will certainly help you make a decision on the purchase.
If you already are a holder of Amtrol DC2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Amtrol DC2.
However, one of the most important roles played by the user manual is to help in solving problems with Amtrol DC2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Amtrol DC2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
