Instruction/ maintenance manual of the product MCD5070 Jensen
Go to page of 10
MCD5070 Inst allation and Operation Manual MARINE CD PLA YER / RECEIVER R E W P O AUX SCN RPT SHF AS/PS EQ SCAN M U T E VOLUME VOLUME MODE BAND AUDIO MCD5070 40W x 4 U D LO.
MCD5070 2 SAFETY INFORMA TION When Driving Keep the volume lev e l Iow enough to b e aware of the surrounding. Protect from Water Do not expose the product directly to water , as th is can cause electrical shorts, fire or other damage.
MCD50 7 0 3 INSTALLATION Before You Begin 1. Disconnect Battery Before you begin, always disconnect the battery negative terminal. 2. Remove T ransport Screws Important Notes • Before final installation, test the wiring co nnections to make sure the unit is connected properly and the system works.
MCD50 7 0 4 DIN Rear Mount (Method B) This unit has threaded holes in the chassis si de panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard . Please consult with your local mobile stereo shop for assistance on this type of installation.
MCD5070 5 WIRING P ower Antenna Connect to power antenna or amplifier , If not used, tape bare end of wire. Ground Connect to ground terminal or clean unpainted metal par t of chassis. Accessory / Ignition Connect to existing radio wire or radio fuse.
MCD5070 6 BA SIC OPERA TION Power On/Off (POWER ) Press the “ ” button(1)to turn the unit ON or OFF . POWER Volume Control When the volume is adjusted, the volume leve l is shown on the display panel as a number ranging from 00 (lowest) to 100 (highest).
MCD5070 7 T UNER OPER A TION Select a Band Press the BAND button (21) on the control panel to change between three FM bands and one AM band. Each band stores up to six preset stations.
MCD5070 8 CD OPER A T ION Insert and Eject Disc Insert a disc, label-side up, with the unit turned on. “CDP PLA Y” will display on the LCD for about 5 Seconds and the unit will play the first track on the disc. Press the eject button (2) to stop disc play And eject the disc.
MCD50 7 0 9 SPECIFICATIONS CD Signal to Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 70dB Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCD50 7 0 ASA Electronics Corporation www .asaelectronics.com © 2006 ASA Electronics Corporation v .071806.
An important point after buying a device Jensen MCD5070 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jensen MCD5070 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jensen MCD5070 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jensen MCD5070 you will learn all the available features of the product, as well as information on its operation. The information that you get Jensen MCD5070 will certainly help you make a decision on the purchase.
If you already are a holder of Jensen MCD5070, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jensen MCD5070.
However, one of the most important roles played by the user manual is to help in solving problems with Jensen MCD5070. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jensen MCD5070 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
