Instruction/ maintenance manual of the product JKRS3 Jensen
Go to page of 16
128-7052 1 of 16 Kit Contents (1) Control Module (1) 3 Button High Frequency Transmitters (1) 5 Button Two Way LED Based Transceiver (1) On Glass Mount Superheterodyne Transceiver (1) Multi Pin Input/.
128-7052 2 of 16 This Remote Start/Keyless Entry System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications.
128-7052 3 of 16 3 THE TRANSCEIVER/ANTENNA ASSEMBL Y : The Superheterodyne Transceiver Antenna Assembly provided with this unit allows routing from below the dash- board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.
128-7052 4 of 16 Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL ST ART SAFETY TEST FOR FURTHER DET AILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch.
128-7052 5 of 16 WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self-tapping screw and ring terminal.
128-7052 6 of 16 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle.
128-7052 7 of 16 7 A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger . In this case, connect the Light Blue Wire to terminal #86 of a external relay .
128-7052 8 of 16 Green/Orange Wire: T ach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil.
128-7052 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Door Lock/Unlock Harness: (White Connector) .
128-7052 10 of 16 10 Resistive Circuits, As W ell As 4 W ire Polarity Reversal and 5 W ire Alternating 12 V olt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface.
128-7052 11 of 16 11 c. Immediately turn the ignition key OFF. d. Hold the program switch ON, then start the vehicle using the ignition key . e. When the unit senses the tach signal, the parking lights will begin to flash. 6. Release the program switch.
128-7052 12 of 16 3. Raise the hood and confirm that the remote start unit shuts down. If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of the Audiovox Remote Start Unit. W ARNING!! DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERA TION OF THE HOOD PIN SAFETY SHUT DOWN FEA TURE.
128-7052 13 of 16 MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device.
128-7052 14 of 16 14 such as the light on reminder . These situations should be carefully considered before altering the vehicle's wiring and must be fully explained to the consumer . Circuits may be used only if the above circuit is not available.
128-7052 15 of 16 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit.
128-7052 16 of 16 © 2004 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-7052.
An important point after buying a device Jensen JKRS3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jensen JKRS3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jensen JKRS3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jensen JKRS3 you will learn all the available features of the product, as well as information on its operation. The information that you get Jensen JKRS3 will certainly help you make a decision on the purchase.
If you already are a holder of Jensen JKRS3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jensen JKRS3.
However, one of the most important roles played by the user manual is to help in solving problems with Jensen JKRS3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jensen JKRS3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
