Instruction/ maintenance manual of the product AIMB-744 Intel
Go to page of 108
AIMB-744 Socket 478 Intel® Pentium® 4/Celeron® Industrial ATX Motherboard with PCI-X/DDR/ AGP/Dual GbE/800 MHz FSB User’s Manual.
AIMB-744 User’s Manual ii Copyright Notice This document is copyrighted, 2004, by Advan tech Co., Ltd. All rights are reserved. Advantech Co ., Ltd. reserves the right to make improve- ments to the products descri bed in this manual at any time withou t notice.
iii 1.0.1 A Message to the Customer Advantech customer services Each and every Advantech pro duct is built to the most exacting specifica- tions to ensure reliable performance in the harsh and demanding condition s typical of industrial environ ments.
AIMB-744 User’s Manual iv Table 1.1: AIMB-744 DDR memory compatibil ity table Memory_Compatibi lity_Test Brand Size Speed Type Memory Apacer 256MB DDR266 DDR infineon HYB25D25680BT-7(32x8) 512MB DDR.
v 1.0.2 Product warranty Advantech warrants to yo u, the original purchaser, that each of its prod- ucts will be free from defects in material s and workmanshi p for two years from the date of purchase.
AIMB-744 User’s Manual vi Step 4. Carefully pack the defective product, a fully-complete d Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A prod- uct returned without proof of t he purchase date is not elig ible for warranty service.
vii Contents Chapter 1 Hardware Co nfiguration ................................. 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Features ............. .............. .............. .............. .
AIMB-744 User’s Manual viii 2.5 USB Ports (CN6/CN63) ................... .............. ................. 20 2.6 VGA Connector (CN7) .................... .............. .............. ... 20 2.7 Serial Ports (COM1 : CN9; COM2 : CN10 ) ......... ....
ix 3.4.8 Swap Floppy Drive ... ........... ............ ...................... ...... 35 3.4.9 Boot UP Floppy Seek ... ................................. ......... ...... 35 3.4.10 Boot Up NumLock Stat us ................. ........... ............. ...
AIMB-744 User’s Manual x 3.6.14 Onboard Serial Port 2 ........... ............ ...................... ...... 42 3.6.15 UART Mode Sele ct ................. ........... ........... ........... .... 42 3.6.16 RxD, TxD Active ............ ........... ..
xi 3.11 Password Setting .......... .............. .............. .............. ......... 48 3.12 Save & Exit Setup ............. ................. .............. ............... 49 3.13 Exit Without Saving ................... ................. .
AIMB-744 User’s Manual xii B.8 External Keyboard Connector (CN12)......................... ... 93 Table B.8:External keyboard connector (CN12) ........ .. 93 B.9 CPU/System Fan Power C onn (CN14/15/37) ................. 94 Table B.9:CPU/Syst em Fan Power Conn (CN14/15/37).
xiii Table B.29:1st M B memory map ........... .............. ...... 104 B.30 PCI Bus Map ................ .............. ................. .............. .... 105 Table B.30:PCI bus map (for VE, E2 vers ion) ....... .... 105 Table B.31:PCI bus map (for VG, G2 version) .
AIMB-744 User’s Manual xiv.
1 CHAPTER 1 General Information.
AIMB-744 User’s Manual 2 Chapter 1 Hardware Configuration 1.1 Introduction Advantech's AIMB-744 series i ndustri al motherboard is designed based on the standard ATX form factor with additional industrial features such as long product life, high reliability and m anageability.
3 1.2 Features 1. Standard ATX form factor with industrial features: AIMB-744 provides industrial features like l ong produ ct life, reliable operation under wide temperature ran ge, watchdog timer, CMOS backup functions, etc.
AIMB-744 User’s Manual 4 drives or fou r enhanced IDE devi ces. Supports PIO mode 4 (16. 67MB/s data transfer rate) and ATA 33/66/100 (33/6 6/100MB/s data tran sfer rate.) BIOS enab led/disabled. • Floppy disk drive interface: Supports up to two floppy disk drives, 5¼" (360 KB and 1.
5 1.3.6 Industrial features • Watchdog timer: Can generate a system reset or IRQ11. Th e watch- dog timer is programmable, with each unit equal to one second or one minute (255 levels) 1.
AIMB-744 User’s Manual 6 Table 1.2: Connectors Label Function CN1 Primary IDE connector CN2 Secondary IDE connector CN3 Floppy drive connector CN4 Parallel port CN6 USB port 4, 5 (shared with CN32) .
7 CN62 8-pin Alarm Board Connector CN64 Case Open SA0 Serial ATA 0 SA1 Serial ATA 1 ATX1 ATX 12V Auxiliary power connector ATX2 ATX power connector Table 1.
AIMB-744 User’s Manual 8 1.5 Board Layout: Jumper and Connector Locations Figure 1.1: Jumper and Connector locations Figure 1.2: I/O Connecto rs CN59 PCI-X 2 PCI- X1 PCI4 PCI3 PCI2 PCI1 AGP1 CN32 CN.
9 1.6 AIMB-744 Block Diagram Figure 1.3: AIMB-744 Block Diagram I n t el 8 2875P 2A T A 1 0 0 po r t s 2 SATA p o r t s 4U S B P o r t s Pr o c e s s o r G- L AN1 : 82 54 7 G I D D R 266 / 333 / 400 D D R 266 / 333 / 400 D D R 266 / 333 / 400 D D R 266 / 333 / 400 A udi o C odec BI OS Su p e r I O Winb on d W836 27 H F Hu b L i n k 1 .
AIMB-744 User’s Manual 10 1.7 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make conne ctions while the power is on. Sensitive electronic compon ents can be damaged by sudden power surges.
11 This device complies with th e requiremen ts in part 15 of the FCC rules: Operat ion is subject to the fol- lowing two conditions: 1.This device may n ot cause harmful interf erence, and 2.
AIMB-744 User’s Manual 12 1.8 Jumper Setti ngs This section provides i nstructions on how to configu re your motherboard by setting the jumpers. It also includes the motherboards's de fault settings and your options for each jumper.
13 problem. Th e J2 jumper set tings c ontrol the outcome of what the com- puter will do in the event the watchd og timer is tripped. 1.8.4 PCI-X 33/66Mhz selection (J5 & J6) The AIMB-744 contains a PCI-X 33/66Mhz selection that enables the PCI-X slots different modes.
AIMB-744 User’s Manual 14 1.8.5 PCI-X slots 3.3V/5V selection (J8) The AIMB-744 cont ains a PCI-X 3.3V/5V selection that provide the u ser to select the operation voltage either 3.3V or 5V. The defau lt setting is 3.3V whic h close pin1 and pin2. By closing pi n2 and pin3, the operatio n voltage change to 5V.
15 The AIMB-744 does not suppo rt ECC (error checking and correctio n). Memory modules with 9 SDRAM ch ips/side support ECC; modules w ith 8 chips/si de do not supp ort ECC. 1.9.2 Dual channel configuration The four DIMM sockets are arra nged in two channels: DIMM1 & DIMM2 in channel A; DI MM3 & DIMM4 in channel B.
AIMB-744 User’s Manual 16 1.11 Cache Memory Since the second-level (L2) cache has been embedded into the Intel® socket 478 Pentium® 4/Celero n™ processor, you do not have to take care of either SRAM chips or SRAM modules. The built-in second-level cache in the processor yields much hi gher performance than the external cache memories.
17 Chapter 2 CHAPTER 2 Connecting Peripherals.
AIMB-744 User’s Manual 18 Chapter 2 Connecting Peripherals 2.1 Introduction You can access most of the connectors from the top of th e board while it is installed in the chassis. If you have a number of cards installed or have a packed chassis, you may need to partially remove the card to make a ll the connections.
19 Chapter 2 Connect the second hard drive to th e remaining connector (CN2 or CN1), in the same way as described above. The secondary IDE shares the same resource with CF (CompactFlash) sock et.
AIMB-744 User’s Manual 20 2.5 USB Ports (CN6 ; shared with CN32) The AIMB-744 provides up to four port s of USB (Universal Serial Bus) interface, which gives complete Plug & Play and hot swapping for up to 127 external devices.The USB interf ace complies with USB Specification Rev.
21 Chapter 2 Different devices implement the RS-232 standa rd in different ways. If you are having problems with a serial device, be su re to check the pin assignments for the connector.
AIMB-744 User’s Manual 22 2.9 CPU Fan Connector (CN14) If fan is used, this connector su pports cooling fans o f 500mA (6W) or less. 2.10 System FAN conn ector (CN15 and CN37) If fan is used, this connector supports cooli ng fans of 500mA (6W) or less.
23 Chapter 2 CN16 is a 5-pin connector for the p ower on LED. Refer to Appendix B for detailed information on the pin assig nments. If a PS/2 or ATX power supply is used, the system 's power LED status w ill be as indicated below: Table 2.
AIMB-744 User’s Manual 24 2.11.6 SM Bus Connector (CN29) This connector is reserved for Advantech's SNMP-1000 HTTP/SNMP Remote System Manager. The SNMP-1000 allows users to monit or the internal voltages, temperature and fans from a remote comp uter through an Ethernet networ k.
25 Chapter 2 The AIMB-744 is equipped with one or two high-performance 10 /100/ 1000 Mbps Ethernet LANs. They are support ed by all major network operating systems. The RJ -45 jacks on the rear plate provide convenient or 10/100/1000 Base-T operation .
AIMB-744 User’s Manual 26 2.16 Aux Line-In connector (AUX IN; CN57) The connector is for audio de vice with Line-in connector. 2.17 Front Panel audio c onnector (FP AUDIO; CN59) The FPAUDIO is a front panel audio connect or compliant with Intel® Front Panel I/O Connectivity Design Guid e.
27 Chapter 2 2.18 8-pin Alarm Board Connector (CN62) The 8-pin alarm board co nnector is for Advantech chassis with alarm board. 2.19 Case Open Connector (CN64) The 2-pin case open connect or is for chassis with case open censor. While opening the case, the buzzer on motherboard will ring.
AIMB-744 User’s Manual 28 which eases cabling to hard drives with th in and long cables. 2.21 Connecting to SNMP -1000 remote manager Use the 6 -pin to 8-pin cable t o connect the mot herboard to SN MP-1000. This cable comes wi th the SNMP-100 0. 2.
29 Chapter 3 CHAPTER 3 Award BIOS Setup.
AIMB-744 User’s Manual 30 Chapter 3 Award BIOS Setup 3.1 Introduction Award’s BIOS ROM has a built-in setup program that allows users to modify the basic system configu ration. This type of inform ation is stored in battery-backed memory (CMOS RAM) so that it retains th e setup information when th e power is turned o ff.
31 Chapter 3 3.2 Entering Setup Turn on the comput er and press <Del> to allo w you to enter the BIOS setup. 3.3 Standard CMOS Setup Choose the “Standard CMOS Features” option from the “Initial Setup Screen” menu, and the screen below will be displayed.
AIMB-744 User’s Manual 32 3.4 Advanced BIOS Features The “Advanced BIOS Features” scr een appears when choosing the “Advanced BIOS Features” item from th e “Initial Setup Screen” menu. It allows the user to configure the AIMB-744 according to his particular requirements.
33 Chapter 3 3.4.5 Quick Power On Self Test Allows the sy stem to skip certain tests while bo oting. This will decrease the time needed to boot the system. 3.4.6 First/Second/Third Boot Device The BIOS tries to load the OS with the devices in the sequence selected.
AIMB-744 User’s Manual 34 3.4.15 Security Option Select whether the password is required every time the system bo ots or only when you enter setup. "System" The system will not boot, and access to Setup will be denied if the correct password is not entered at the p rompt.
35 Chapter 3 3.5.1 DRAM Timing Selectable This item allows you to cont rol the DRAM speed. The selections are "Manual" or "By SPD". 3.5.2 CAS Latency Time This controls the latency between DDR RAM read command and the time that the data actually becomes av ailable.
AIMB-744 User’s Manual 36 3.5.7 System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h- FFFFFh, resulting in better system performance. Howev er, if any pro- gram writes to this memory area, a system error may occur.
37 Chapter 3 3.6 Integrated Peripherals Figure 3.5: Integrated peripherals Figure 3.6: On-Chip IDE Device.
AIMB-744 User’s Manual 38 3.6.1 IDE HDD Block Mode If your IDE hard drive supports bl ock mode select Enabled for automatic detection of the optimal number of bl ock read/writes per sector the drive can support.
39 Chapter 3 3.6.5 USB Controller Select Enabled if your system contains a Universal Serial Bus (USB) con- troller and you have USB peripherals. The choices: "Enabled", "Dis- abled". 3.6.6 USB 2.0 Controller This entry is for disable/enable USB2 .
AIMB-744 User’s Manual 40 3.6.12 Onboard FDC Cont roller When enabled, this field allo ws you to connect your floppy d isk drives to the onboard floppy disk drive connector instead of a separate controller card. If you want to use a different controller card to connect the floppy disk drives, set this field to Disabled.
41 Chapter 3 This field allows you to select EPP port type 1.7 or 1.9. The choices: "EPP1.9", "EPP1.7". 3.6.22 ECP Mode Use DMA This selection is available only if yo u select “ECP” or “ECP + EPP” in the Parallel Port Mode field.
AIMB-744 User’s Manual 42 The Choice : "S1(POS)", and "S3(STR)". While se lecting "S3(STR)", the "Run VGABIOS if S3 Resume" and "Resume on USB from S3" will be active for selection.
43 Chapter 3 This field allows you to select the CPU THR M-Throttling rate. The choices: "75.0%", "5 0.0%", and "25. 0%". 3.7.10 Resume on LAN/PCI PME# To enabled or disable the function to resume the system by PCI card or LAN.
AIMB-744 User’s Manual 44 3.8.1 Reset Configuration Data Default is Disable. Select Enable to reset Extend ed System Configuration Data (ESCD) if you have inst alled a new add-on and system configura- tion has caused such a conflict that OS cannot boot.
45 Chapter 3 3.9.4 Current CPUFAN Speed This shows you the curren t CPUFAN operating speed. 3.9.5 VCORE, +1.5V, VCC3, +5V, +12V, -12V, -5V, VBAT(V), 5VSB(V) This shows you the voltage o f VCORE, +1.5V, VCC3, +5V, +12V, -12V, -5V, VBAT(V), and 5VSB(V).
AIMB-744 User’s Manual 46 Press <Enter>. 2. If the CMOS is good or if this option has been used to change the default passw ord, the user is asked for the password stored in the CMOS. The screen will display th e following message: Enter the current passw or d and press <Enter>.
47 Chapter 4 CHAPTER 4 Chipset Software Installation Utility.
AIMB-744 User’s Manual 48 Chapter 4 Chipset Software Install Utility 4.1 Before you begin To facilitate the installation of the enhanced display device drivers and utility software, you shoul d read the instructions in this chapter carefully before you attempt installatio n.
49 Chapter 4 • Identification of Intel ® chipset compon ents in the Device Manager. • Integrates superior video features. These include filtered sealing of 720 pixel DVD cont ent, and MPEG-2 motion co mpensation for soft- ware DVD Windows 98SE Windows 2000 Windows Me Windows XP 4.
AIMB-744 User’s Manual 50 2. Click "Next" when you see the following message. 3. Click "Yes" when you see the following message..
51 Chapter 4 4. Click "Next" when you see the following message. 5. When the following message appear s, click "Finish" to complete the installation an d restart Windows.
AIMB-744 User’s Manual 52.
53 Chapter 5 CHAPTER 5 LAN Configuration.
AIMB-744 User’s Manual 54 Chapter 5 LAN Configuration 5.1 Introduction The AIMB-744 features the 32-bit 10/ 100/1000 Mbps Ethernet network interface.
55 Chapter 5 5.3 Installation The AIMB-744's onboard Ethernet interface supports all major network operating systems. However, the installation proced ure varies with differ- ent operating systems. In the following sections, refer to the one that pro- vides driver setup procedure for the operating system you are using.
AIMB-744 User’s Manual 56 2. Select "I accept the terms in th e license agre ement" and click "Next" to continue. 3. Click "Next" to continue.
57 Chapter 5 4. Click "Install Soft ware" to start the installation procedure. 5. The driver will be installed au t omatically and the LAN function will be enabled after the installation.
AIMB-744 User’s Manual 58.
59 Chapter 6 CHAPTER 6 Onboard Security Setup.
AIMB-744 User’s Manual 60 Chapter 6 Onboard Security Setup 6.1 Introduction The AIMB-744's hardw are monitor i s designed with Winbon d W83782D. Onboard security (OBS) fun ctions monitor key hardware. They help yo u maintain your system's stabi lity and durability.
61 Chapter 6 6.2 Windows XP Driver Setup 1. Insert the driver CD into your syst em's CD-ROM drive. In a few seconds, the software installation main menu appears, as shown in the following figure. Click on the "Ins tall" button under the "OBS DRIVERS" heading.
AIMB-744 User’s Manual 62 3. Click "Next" when you see the following message. 4. Click "Next" when you see the following message.
63 Chapter 6 5. Click "Next" to continue. 6. Click "Finish" when you see the following message..
AIMB-744 User’s Manual 64 6.3 Using the OBS Hardwa re Doctor Utility After completing the setup, all th e OBS functions are permanently enabled. When a monitored reading exceeds safe limits, a warning mes- sage will be displayed and an error b eep tone will activate to attract your attention.
65 Chapter 6.
AIMB-744 User’s Manual 66.
67 Appendix A Appendix A Programming the Watchdog Timer.
AIMB-744 User’s Manual 68 Appendix A Programming the watchdog timer A.1 Programming the Watchdog Timer The AIMB-744's watchdo g timer can be used to moni tor system software operation and take correc tive action if the software fails to functio n after the programmed period.
69 Appendix A Unlock W83627H Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog time r Lock W83627HF.
AIMB-744 User’s Manual 70 Watchdog Timer Registe rs Address of regis ter (2E) Attribute Read/Write Value (2F) and description 87 (hex) ----- Write this address to I/O address port 2E (hex) twice to unlock theW83627HF 07 (hex) write Write 08 (hex) to select reg- ister of watchdog timer.
71 Appendix A Table A.1: Watchdog timer registers A.1.4 Example Program 1. Enable watchdog timer and set 10 sec. as timeout interval ;-------- --------- ----------- ---------- --------- ---------- -- .
AIMB-744 User’s Manual 72 ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; Set second as counting unit Mov al,0f5h Out dx,al Inc dx In al,dx And al,not 08h Out dx,al ;----.
73 Appendix A ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- ---.
AIMB-744 User’s Manual 74 Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;--------.
75 Appendix A Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;-------- --------- ---.
AIMB-744 User’s Manual 76 Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;--------.
77 Appendix B Appendix B I/O Pin Assignments.
AIMB-744 User’s Manual 78 Appendix B Pin Assignments B.1 IDE Hard Drive Connector (CN1, CN2) Table B.1: IDE hard drive connector (CN1, CN2) Pin Signal Pin Signal 1 IDE RESET* 2 GND 3D A T A 7 4 D A .
79 Appendix B B.2 Floppy Drive Connector (CN3) Table B.2: Flop py dr ive connector (CN3) Pin Signal Pin Signal 1 GND 2 FDHDIN* 3G N D 4 N / C 5 N/C 6 FDEDIN* 7 GND 8 INDEX* 9 GND 10 MOTOR 0* 11 GND 12.
AIMB-744 User’s Manual 80 B.3 Parallel Port Connector (CN4) Table B.3: Parallel port connector (CN4) Pin Signal Pin Signal 1 STROBE* 14 AUTOFD* 2D 0 1 5E R R 3D 1 1 6I N I T * 4D 2 1 7 S L C T I N I.
81 Appendix B B.4 USB Connector (C N6; shared with CN32) B.5 COM1/2/3/4 RS-232 Se rial Port Interface (CN9/10/ 23/38) Table B.4: USB1/USB2 connector (CN6; shared with CN32) Pin USB1 Signal Pin U SB2 Signal 1+ 5 V 6 + 5 V 2 UV- 7 UV- 3 UV+ 8 UV+ 4G N D 9 G N D 5 Chassis GND 10 N /CA Table B.
AIMB-744 User’s Manual 82 B.6 Keyboard and Mouse Connnecto r (CN11) B.7 COM3/4 serial po rt connector ( CN10/23) 9R I Table B.6: Keyboard and mous e connector (CN11) Pin Signal 1 KB DATA 2N / C 3G N D 4 KB VCC 5 KB CLK 6 N / C Table B.
83 Appendix B B.8 External Keyboard Connector (CN12) B.9 CPU/System Fan Power Conn (CN14/15/37) 8R I 9G N D Table B.8: External keyboard connecto r (CN12) Pin Signal 1C L K 2D A T A 3N C 4G N D 5 VCC Table B.
AIMB-744 User’s Manual 84 B.10 Power LED (CN16) You can use an LED to indicate when the motherboard is on. Pin 1 of CN16 supplies the LED's power, and Pin 3 is the ground. B.11 External Speaker Connector (CN17) The motherboard has its own buzzer.
85 Appendix B B.12 Reset C onnector (CN18) B.13 HDD LED Connector (CN19) Table B.12: Reset connector (CN18) Pin Signal 1 RESET 2G N D Table B.13: HDD LED connector (CN19) Pin Signal 1V C C ( L E D + ).
AIMB-744 User’s Manual 86 B.14 ATX Soft Po wer Switch (CN21) Table B.14: ATX soft power switch (CN21) Pin Signal 15 V S B 2P W R - B T N 1.
87 Appendix B B.15 H/W Monitor Alarm (CN22) B.16 SM Bus Connector (CN29) B.17 USB/LAN ports (CN31 and CN32) Table B.15: H/W monitor alarm (CN22) Pin Signal 1 Enable OBS alarm 2 Disable OBS alarm Table B.16: SM Bus Connector (CN 29) Pin Signal 1S M B _ D A T A 2S M B _ C L K Table B.
AIMB-744 User’s Manual 88 B.18 Line Out, Mic IN connector (CN55) B.19 Audio input from CD-ROM (CD IN; CN56) Table B.18: Ethernet 10 /100Ba se-T RJ-45 port Pin Signal Pin Signal 1X M T + 5 N / C 2 XMT- 6 RCV- 3R C V + 7 N / C 4 N/C 8 N/C Table B.
89 Appendix B B.20 Aux Line-In c onnector (AUX IN; CN57) B.21 Front Panel audio connector (FP AUDIO; CN59) Table B.20: Aux Line-In connector (AUX IN ; CN57) Pin Signal Pin Signal 1A U X _ L 3 G N D 2 GND 4 AUX_R Table B.
AIMB-744 User’s Manual 90 B.22 Case Open Connector (CN64) B.23 8-pin Alarm Bo ard Connector (CN62) Table B.22: Case Open Connector (CN64) Pin Signal 1 CASEOP 2G N D Table B.
91 Appendix B B.24 System I/O Ports Table B.24: System I/O ports Addr. rang e (Hex) D evice 000-01F DMA controller 020-021 Interrupt controller 1, master 022-023 Chipset address 040-05F 8254 timer 060.
AIMB-744 User’s Manual 92 B.25 DMA Channel Assignments B.26 Interrupt Assignments Table B.25: DMA channel assignments Channel Functio n 0 Available 1 Available 2 Floppy disk (8-bit transfer) 3 Available 4 Cascade for DMA controller 1 5 Available 6 Available 7 Available Table B.
93 Appendix B B.27 1st MB Memory Map B.28 PCI Bus Map B.29 PCI-X bus map Table B.27: 1st MB memory map Addr. range (Hex) Device E0000h - FFFFFh BIOS CC000h - DFFFFh Unused C0000h - CBFFFh VGA BIOS A0000h - BFFFFh Video Memory 00000h - 9FFF Fh Base memory Table B.
AIMB-744 User’s Manual 94.
An important point after buying a device Intel AIMB-744 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Intel AIMB-744 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Intel AIMB-744 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Intel AIMB-744 you will learn all the available features of the product, as well as information on its operation. The information that you get Intel AIMB-744 will certainly help you make a decision on the purchase.
If you already are a holder of Intel AIMB-744, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Intel AIMB-744.
However, one of the most important roles played by the user manual is to help in solving problems with Intel AIMB-744. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Intel AIMB-744 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
