Instruction/ maintenance manual of the product ST2 Integra
Go to page of 28
ST2 Smar t T uner INSTRUCTION MANUAL Dual AM/FM T uner.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER - SERVICEABLE P ARTS INSIDE. REFER SER VICING TO QUALIFIED SER VICE PERSONNEL.
T ABLE OF CONTENTS Pr oduct Introduction ..........................................................................................................4-5 Component Guide ST2 Front Panel ....................................................................
4 INTRODUCTION DESCRIPTION Thank you for choosing the Russound ST2 Smart T uner . Whether you are adding radio to an exist- ing system, expanding a CAi Series system or taking advantage of the CAV6.6’ s robust RNET™ communication link, the ST2 T uner is designed to meet your needs.
5 INTRODUCTION IR-contr olled System CAi Series - The ST2 T uner can be controlled by infrar ed commands received thr ough the two IR connec- tions on the rear panel. The ST2 contains two individual tuners, which makes it act as two sources in the CAi system.
6 COMPONENT GUIDE ST2 FRONT P ANEL MAIN POWER SWITCH - T urns power on and off POWER ON/OFF LED - Indicates power on or off REMOVABLE COVER LENS - Covers the selection buttons on the tuner BANK SELECT.
7 RS-232 INTERFACE IR LR A UDIO O UTPUT 12VDC 1.5A I N O UT NEWMARKET, NH U.S.A. ST2 Smart Tuner LINK K EYP AD P ORTS T UNER 1 T UNER 2 FM C OAX L OOP A NTENNA FM C OAX L OOP A NTENNA Serial# MADE IN .
8 TUNE TUNE FAV 1 SEEK ST/ MONO LOC/ DX SEEK TUNE TUNER 1 TUNER 2 4 M E M B A N K 123 56 789 0 PWR MEM TUNE AM/FM FAV 2 OK POWER - Puts the tuner in/out of standby mode TUNER CONTROL - Select T uner 1.
9 ST2 SETUP AND CONNECTIONS BASIC CONNECTIONS Power T o power the tuner , connect the 12VDC external power supply by inserting the power supply jack into the power supply connection on the tuner’ s r ear panel. Audio Output Connect one end of a dual RCA audio cable to the T uner 1 Audio Output connection.
10 RS-232 INTERFACE IR LR A UDIO O U TP U T 1 2 VD C 1.5 A I N O U T NE WM AR K ET , N HU . S . A . ST2 Smart Tuner LIN K K E YP A D P O RTS T U N ER 1 T U N ER 2 F M C O AX L OO P A N T E NN A F M C O AX L OO P A N T E NN A S erial# M A D E IN K O REA IR L R A UDIO O U TP U T ST2 T uner CA V 6.
11 ST2 SETUP AND CONNECTIONS CAi SERIES AND A-BUS CONNECTIONS 1 R L 2 1 R L 2 34 CA6 .4i NEWMARKET , NH U.S.A. ~110VAC ~220-240VA C ~50-60Hz 400W VOL TAG E 110V 220-240V FUSE F4A F2A K EYPAD P ORTS Z .
12 ST2 SETUP AND CONNECTIONS ANTENNA CONNECTIONS Connecting an Indoor and Outdoor Antenna The diagram above depicts a typical setup using the ST2 T uner with the included FM antenna and AM loop antenna. Also shown are two outdoor antenna options (not included).
13 ST2 SETUP AND CONNECTIONS ANTENNA CONNECTIONS Gr ounding an Outdoor Antenna If the tuner is used with an outdoor antenna, the antenna must be grounded against static char ges and voltage sur ges. Consult the instructions that came with the antenna or contact the antenna manu- facturer for pr oper installation instructions.
14 Fr ont Panel Operation T urning the unit on T o turn the unit on, push the On/Off button up on the front panel. Pushing the On/Off button down turns the tuner off. Selecting the desired tuner From the fr ont panel, use to toggle between T uner 1 and T uner 2.
15 ST2 OPERA TION ST2-RC REMOTE CONTROL ST2-RC Remote Contr ol Operation T urning the unit on T o take the ST2 tuner out of standby mode, push or any other button except TUNER 1 or TUNER 2.
16 ST2 OPERA TION ST2-KP KEYP AD CONTROLS ST2-KP Keypad Operation T urning the keypad on/of f T o activate the ST2-KP , press . Pr ess to power down the keypad display . The keypad remains powered until the ST2 T uner is turned off. Selecting the desired tuner T o select a different tuner , press and hold .
17 ST2 OPERA TION UNO-S2 KEYP AD CONTROLS WITH CAV6.6 CA V6.6-UNO-S2 Keypad Operation NOTE: T o contr ol the ST2 T uner through the UNO-S2 keypad, the tuner must be configured as a source using the CA V6.6 programming steps. T urning the unit on The tuner is power managed by the CAV6.
18 ST2 OPERA TION UNO-S2 KEYP AD CONTROLS WITH CAV6.6 104.1 MHz FM TUNER SELECTION - Select source number assigned to TUNER 1 or TUNER 2 TUNE UP/DOWN - Used for manual station selection SELECT - Selec.
19 UNO-LRC1 Remote Contr ol Operation T urning the unit on The tuner is power managed by the CAV6.6 or other RNET -enabled controller . If the tuner is in standby mode, any button press of the UNO-LRC1 will bring the tuner out of standby mode when used with the UNO keypad.
20 ST2 OPERA TION UNO-LRC1 REMOTE CONTROL WITH CA V6.6 POWER - Power managed by CAV6.6 NUMERIC INPUT - Number buttons for direct input of frequency , preset, bank TUNE UP/DOWN - Incrementally scr olls.
21 ST2 T uner Setup Menus Note: The Setup Menu procedur es must be per formed fr om the ST2 T uner front panel. The ST2 T uner Setup Menus provide setup and naming pr ocedures for the ST2 main chassis, and each AM/FM tuner module.
22 ST2 TUNER PROGRAMMING ST2 TUNER SETUP MENU Press and Hold TNR SEL button ST2 Chassis Setup Pr oc e dures TNR SEL TNR SEL This Procedure returns the ST2 Tuner to its Factory settings SOURCE NUM Proc.
23 System Info (Chassis) The System Info menu shows the ST2 T uner’ s manufacturing build properties. 1. Enter the Setup Menu by pressing and holding the TNR SEL button. 2. TUNER SETUP appears. Press MEM Up/Down until SYSTEM INFO appears on the tuner .
24 ST2 TUNER PROGRAMMING ST2 TUNER SETUP MENU Bank Name (AM/FM) (cont’d) 14. Press BAND to save bank name. The Bank Name menu returns to the T uner # prompt to name other banks, or press TNR SEL to exit the Bank Name menu. Region (AM/FM) The Region procedur e assigns either US or Euro to the tuner .
25 ST2 TUNER PROGRAMMING PROGRAMMING FOR CAV6.6 USE NOTE: The CAV6.6 firmwar e must be version 2.00.01 or higher and UNO-S2 firmwar e must be version 3.00.01 or higher to control the ST2 T uner . Use the System Info Menu of the CAV6.6 to check the firmwar e version.
26 ST2 Smart T uner Dimensions: 17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm) Weight: 7 lbs. (3.2kg) Power Supply: 12VDC 1.5A Frequency Range: AM 530 - 1710 kHz FM 87.
27 WARRANTY & REP AIR The Russound ST2 T uner is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of pur chase. During this period, Russound will replace any defective parts and correct any defect in workmanship without char ge for either par ts or labor .
Russound 5 Forbes Road, Newmarket, NH 03857 tel 603.659.5170 • fax 603.659.5388 e-mail: tech@russound.com www .russound.com E. & O.E. Copyright © 2004 Russound ® All rights reserved. All trademarks are pr operty of their respective owners. Rev .
An important point after buying a device Integra ST2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Integra ST2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Integra ST2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Integra ST2 you will learn all the available features of the product, as well as information on its operation. The information that you get Integra ST2 will certainly help you make a decision on the purchase.
If you already are a holder of Integra ST2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Integra ST2.
However, one of the most important roles played by the user manual is to help in solving problems with Integra ST2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Integra ST2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
