EN
InFocus logo
Official user manual

InFocus X7

37 pages·3.1 MB·Projector·PDF·ENDEFRITNLJA
InFocus X7
Table of Contents 39 sections Reference Guide · Usage Notice · Important Operating Considerations for Safety · Introduction · … ShowHide
Page 1 of the InFocus X7 user manual — Reference Guide
Page 1 · click to enlarge
Page 1
InFocus X7 — Reference Guide diagram (page 1)
Fig. 1 · Reference Guide

Reference Guide

InFocus X7 — Reference Guide diagram (page 1)
Fig. 2 · Reference Guide
Page 2 of the InFocus X7 user manual — Reference Guide
Page 2 · click to enlarge
Page 2
Page 2 of the InFocus X7 user manual — Reference Guide
Page 3 of the InFocus X7 user manual — Usage Notice
Page 3 · click to enlarge
Page 3
InFocus X7 — Usage Notice diagram (page 3)
Fig. 3 · Usage Notice

Usage Notice

Precautions Follow all warnings, precautions and maintenance as recom mended in this user’s guide to maximize the life of your unit.

on. The bright light may hurt your eyes.

this product to rain or moisture.

may cause electric shock.

down, and follow all changing instructions.

accordance with local disposal laws. See www.lamprecycle.org

be sure to change the lamp when it shows warning mes sages.

Display “Default Setting” menu after replacing a new lamp module (refer to page 25).

out and may make a loud popping sound. If this hap pens, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp”.

Page 4 of the InFocus X7 user manual — Usage Notice
Page 4 · click to enlarge
Page 4

Usage Notice

Do:

Turn off the product before cleaning.

Use a soft cloth moistened with mild detergent to clean the display housing.

Disconnect the power plug from AC outlet if the product is not being used for a long period of time.

Don’t:

Block the slots and openings on the unit provided for ventila tion.

Use abrasive cleaners, waxes or solvents to clean the unit.

Use under the following conditions: - In extremely hot, cold or humid environments. - In areas susceptible to excessive dust and dirt. - Near any appliance that generates a strong magnetic field.

Page 5 of the InFocus X7 user manual — Usage Notice
Page 5 · click to enlarge
Page 5

Usage Notice

Important Operating Considerations for Safety

Place the projector in a horizontal position no greater

than 15 degrees off axis.

Locate the projector in a well-ventilated area without any

obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.

Locate the projector at least 4' (1.2 m) away from any

heating or cooling vents.

Use only the power cord provided. A surge-protected

power strip is recommended.

Refer to this guide for proper startup and shutdown pro

cedures.

In the unlikely event of a lamp rupture, particles may exit

through the projector side vents. When the projector is turned on, keep people, food, and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below.

Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty booklet.

2’ / 0.6 m

3’ / 1 m

5’ / 1.5 m

8’ / 2.4 m

Page 6 of the InFocus X7 user manual — Introduction
Page 6 · click to enlarge
Page 6

Introduction

Product Features This product is a SVGA/XGA single chip 0.55” DLP® projec tor. Outstanding features include:

True SVGA, 800 x 600 addressable pixels True XGA, 1024 x 768 addressable pixels

Single chip Dark Chip2TM DLP® technology

NTSC/NTSC4.43/PAL/PAL-M/PAL-N/SECAM and

SDTV(480i/576i), EDTV(480p/576p), HDTV(720p/1080i) compatible

Multi-Auto functionsAuto detection, Auto image and

Auto saving the adjustments

Full function remote control

User friendly multilingual on screen display menu

Advanced digital keystone correction and high quality

full screen image re-scaling

Built-in one 2-Watt speaker.

SXGA+, SXGA compression and VGA, SVGA re-sizing

(XGA) SXGA, XGA compression and VGA re-sizing (SVGA)

Mac compatible

Page 7 of the InFocus X7 user manual — Introduction
Page 7 · click to enlarge
Page 7

Introduction

Package Overview

This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immedi ately if anything is missing.

InFocus X7 — Introduction diagram (page 7)
Fig. 4 · Introduction

Due to the difference in applications for each country, some regions may have different accessories.

Power Cord VGA Cable

Document Pack

Page 8 of the InFocus X7 user manual — Introduction
Page 8 · click to enlarge
Page 8

Introduction

InFocus X7 — Introduction diagram (page 8)
Fig. 5 · Introduction
1. Power 2. Remote Controller 3. IR Receiver 4. Zoom and Focus Lever 5. Speaker 6. Lens 7. Lens Cap
Page 9 of the InFocus X7 user manual — Connection Ports
Page 9 · click to enlarge
Page 9

Introduction

Connection Ports

InFocus X7 — Connection Ports diagram (page 9)
Fig. 6 · Connection Ports
1. Computer Input Connector 2. Video 1: S-Video Input Connector 3. Video 2: Composite Video Input Connector 4. Serial Control Connector 5. Monitor Output Connector 6. Audio Input Connector 7. Power Socket 8. Kensington TM Lock Port
Page 10 of the InFocus X7 user manual — Introduction
Page 10 · click to enlarge
Page 10

Introduction

InFocus X7 — Introduction diagram (page 10)
Fig. 7 · Introduction

To remove remote con troller from the projector, you may simply press down the top-center of the remote controller, then the remote control ler will bounce up to be removed.

Please DO NOT remove the remote con troller by other means than the method stated. Any improper action to remove the remote controller may cause damage to the slot.

1 Power Refer to the “Power On/Off the Projector” section on pages 12-13.

2 Display Mode Select the display mode from PC, Movie, sRGB, Game and User.

Press “computer” to choose com puter in connector.

4 Freeze To pause the screen image.

3 Computer Source

Page 11 of the InFocus X7 user manual — Introduction
Page 11 · click to enlarge
Page 11

Introduction

Adjust the image to compensate for distortion caused by tilt ing the projector (vertical ± 15 degrees).

6 Source Press “source” to choose RGB, Component, S-Video, Composite and HDTV sources.

7 Menu Press “menu” to launch the On screen display (OSD) menu, back to the top level of OSD menu for the OSD main menu operation

8 AV-Mute Momentarily turn off/on the audio and video.

9 Reset Change the adjustments and set tings to the factory default value.

10 Video 1 Source (S-Video)

Press “video 1” to choose video 1 connector.

11 Video 2 Source (Composite)

Press “video 2” to choose video 2 connector.

12 Digital Zoom Zoom the projector display in or out.

13 Enter Confirm your section of items in sub menu operation.

14 Re-Sync Automatically synchronize the projector to the input source.

15 Four Directional Select Keys

Use up, down, left, right s to select items or make adjustments to your selection.

16 Source Lock Press “source-lock” to lock speci fied connection port; press this again to unlock.

17 Volume -/+ Increase/decrease speaker vol ume.

5 Keystone Correction

Page 12 of the InFocus X7 user manual — VGA, DVI
Page 12 · click to enlarge
Page 12

Operation

Connecting the Projector

VGA, DVI

InFocus X7 — VGA, DVI diagram (page 12)
Fig. 8

Due to the difference in applications for each country, some regions may have different accessories.

1 Power cord 2 D-15 to RCA adapter for YPbPr 3 VGA in cable 4 S-Video cable 5 Composite video cable 6 RS232 cable 7 VGA out cable 8 Audio cable jack to jack

To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with your projector.

Page 13 of the InFocus X7 user manual — Powering On the Projector
Page 13 · click to enlarge
Page 13

Operation

Powering On/Off the Projector

Powering On the Projector

1. Remove the lens cap. 2. Ensure that the power cord and signal cable are securely connected. The Power LED will turn flash blue. 3. Turn on the lamp by pressing “Power/Standby” on the control panel. The startup screen will display for about 25 seconds and the Power LED will turn blue. 4. Turn on your source (computer, notebook, video player,etc.) The projector will detect your source automatically.

If you connect multiple sources at the same time, use the “source” on the remote control or use the “computer“, ”video 1”, “video 2“ on the remote control to switch.

InFocus X7 — Powering On the Projector diagram (page 13)
Fig. 9 · Powering On the Projector

Turn on the projector first and then the signal sources.

Page 14 of the InFocus X7 user manual — Powering off the projector
Page 14 · click to enlarge
Page 14

Operation

Powering off the projector

1. Press the “Power/Standby” to turn off the projector lamp, you will see a message as below on the on-screen display.
InFocus X7 — Powering off the projector diagram (page 14)
Fig. 10 · Powering off the projector

2. Press the “Power/Standby” again to confirm. 3. The cooling fan continues to operate for about 120 seconds for cooling cycle and the Power LED will flash blue. When the light starts flashing, the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press “Power/Standby” to restart the projector. 4. Disconnect the power cord from the electrical outlet and the projector. 5. Do not turn on the projector immediately following a power off procedure.

Page 15 of the InFocus X7 user manual — Warning Indicator
Page 15 · click to enlarge
Page 15

Operation

Warning Indicator

When the “Power” LED indicator turns red, it indicates the

projector has overheated. The projector will automatically shut itself down.

InFocus X7 — Warning Indicator diagram (page 15)
Fig. 11 · Warning Indicator

When the “Power” LED indicator flashes red and the mes

sage below displays onscreen, it indicates the projector will detect the lamp life itself. When you see this message, change the lamp as soon as possible or contact your local dealer or our service center.

InFocus X7 — Warning Indicator diagram (page 15)
Fig. 12 · Warning Indicator

When the “Power” LED indicator flashes red and the mes

sage below displays onscreen, it indicates the fan failed. Stop using the projector and disconnect the power cord from the electrical outlet, then contact your local dealer or our service center.

InFocus X7 — Warning Indicator diagram (page 15)
Fig. 13 · Warning Indicator
Page 16 of the InFocus X7 user manual — Adjusting the Height of Projector Image
Page 16 · click to enlarge
Page 16

Operation

Adjusting the Projected Image

Adjusting the Height of Projector Image

The projector is equipped with elevator feet for adjusting the height of image.

To raise/lower the image:

1. Use to fine-tune the display angle .
InFocus X7 — Adjusting the Height of Projector Image diagram (page 16)
Fig. 14 · Adjusting the Height of Projector Image

Tilt adjusting wheel Tilt adjusting wheel

Page 17 of the InFocus X7 user manual — Adjusting the Projector Zoom / Focus
Page 17 · click to enlarge
Page 17

Operation

Adjusting the Projector Zoom / Focus

You may turn the zoom lever to zoom in or out. To focus the image, rotate the focus ring until the image is clear. The pro jector will focus at distances from 3.9 to 39.4 feet (1.2 to 12.0 meters) with mechanical travel.

InFocus X7 — Adjusting the Projector Zoom / Focus diagram (page 17)
Fig. 15 · Adjusting the Projector Zoom / Focus
InFocus X7 — Adjusting the Projector Zoom / Focus diagram (page 17)
Fig. 16 · Adjusting the Projector Zoom / Focus

This graph is for user’s reference only.

Page 18 of the InFocus X7 user manual — How to operate
Page 18 · click to enlarge
Page 18

On Screen Display Menus

The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source.

How to operate

1. To open the OSD menu, press “Menu” on the Remote Control.
2. When OSD is displayed, use keys to select any item in the

main menu. While making a selection on a particular page, press

key to enter sub menu.

3. Use keys to select the desired item in the sub menu and

adjust the settings by key.

4. If the setting has icon, you could press “Enter” to enter another

sub menu. Press “Menu” to close the sub menu after adjustment.

5. After adjusting the settings, press “Menu” back to the main menu.
6. To exit, press “Menu”again. The OSD menu will be closed and the

projector will automatically save the new settings.

InFocus X7 — How to operate diagram (page 18)
Fig. 17 · How to operate

Main Menu · Sub Menu Setting

Page 19 of the InFocus X7 user manual — Image
Page 19 · click to enlarge
Page 19
InFocus X7 — Image diagram (page 19)
Fig. 18 · Image

Image

(PC Mode)

Display Mode There are many factory presets optimized for various types of im

ages.

PC: For computer or notebook.

Movie: For home theater.

sRGB: For standard color.

Game: For game.

User: Memorize user’s settings. Brightness Adjust the brightness of the image.

Press the to darken image.

Press the to lighten the image. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.

Press the to decrease the contrast.

Press the to increase the contrast.

Page 20 of the InFocus X7 user manual — Frequence  “Frequence” changes the display data frequency to match the fre
Page 20 · click to enlarge
Page 20

Frequence “Frequence” changes the display data frequency to match the fre

quency of your computer’s graphic card. If you experience a vertical flickering bar, use this function to make an adjustment. Tracking Synchronize the signal timing of the projector with the graphics

card. If you experience an unstable or flickering image, use this function to correct it. White Peaking Use the white peaking control to set the white peaking level of

DMD chip. 0 stands for minimal peaking, and 10 stands for maxi mum peaking. If you prefer a stronger image, adjust towards the maximum setting. For a smooth and more natural image, adjust towards the minimum setting. Color Temp. Adjust the color temperature. At higher temperature, the screen

looks colder; at lower temperature, the screen looks warmer.

Degamma This allows you to choose a degamma table that has been fine-tuned

to bring out the best image quality for the input.

Page 21 of the InFocus X7 user manual — Image
Page 21 · click to enlarge
Page 21
InFocus X7 — (Video Mode) diagram (page 21)
Fig. 19 · (Video Mode)

Image

(Video Mode)

Display Mode There are many factory presets optimized for various types of im

ages.

PC: For computer or notebook.

Movie: For home theater.

sRGB: For standard color.

Game: For game.

User: Memorize user’s settings. Brightness Adjust the brightness of the image.

Press the to darken image.

Press the to lighten the image. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.

Press the to decrease the contrast.

Press the to increase the contrast.

Page 22 of the InFocus X7 user manual — (Video Mode)
Page 22 · click to enlarge
Page 22

Color Adjust a video imge from black and white to fully saturated color.

Press the to decrease the amount of color in the image.

Press the to increase the amount of color in the image. Tint Adjust the color balance of red and green.

Press the to increase the amount of green in the image.

Press the to increase the amount of red in the image. Sharpness Adjust the sharpness of the image.

Press the to decrease the sharpness.

Press the to increase the sharpness. White Peaking Use the white peaking control to set the white peaking level of

DMD chip. 0 stands for minimal peaking, and 10 stands for maxi mum peaking. If you prefer a stronger image, adjust towards the maximum setting. For a smooth and more natural image, adjust towards the minimum setting. Color Temp. Adjust the color temperature. At higher temperature, the screen

looks colder; at lower temperature, the screen looks warmer.

Degamma This allows you to choose a degamma table that has been fine-tuned

to bring out the best image quality for the input.

Page 23 of the InFocus X7 user manual — Display Setting
Page 23 · click to enlarge
Page 23
InFocus X7 — Display Setting diagram (page 23)
Fig. 20 · Display Setting

Display Setting

Adjust image distortion caused by tilting projector. (±15 degrees). H-Position (Horizontal Position) Press the to move the image left. Press the to move the image right. V-Position (Vertical Position) Press the to move the image down.

Press the to move the image up. Aspect Ratio Use this function to choose your desired aspect ratio.

4:3

This format is for 4x3 input sources not enhanced for Wide- screen TV.

16:9

This format is for 16:9 input sources, like HDTV and DVD en hanced for Widescreen TV.

This format displays the original image without any scaling.

Keystone · Native

Page 24 of the InFocus X7 user manual — Display Setting
Page 24 · click to enlarge
Page 24

The factory default setting.

When you select this function, the projector reverses the image so you can project behind a translucent screen.

When you select this function, the projector turns the image upside down for ceiling-mounted projection.

When you select this function, the projector reverses and turns the image upside down at same time. You can project from be hind a translucent screen with ceiling mounted projection.

Show 5 more labels / short text on this page
Projection · Front-Desktop · Rear-Desktop · Front-Ceiling · Rear-Ceiling
Page 25 of the InFocus X7 user manual — Default Setting
Page 25 · click to enlarge
Page 25

Default Setting

When this function is turned “Off”, the projector will search for

other signals if the current input signal is lost. When this function is turned “On”, it will search specified connection port.

Choose “On” to turn on Fan Control mode. Operate the fan at full speed continuously to allow for proper high altitude cooling of the projector. Lamp Reminding

Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will show up 30 hours before end of life.

Choose “On” to provide true, more vibrant colors in picture. Auto Power Off Set the interval of power-off of the system, if there is no signal

input. (In minutes)

Source Lock · Fan Control · Brilliant ColourTM

Page 26 of the InFocus X7 user manual — Default Setting
Page 26 · click to enlarge
Page 26
InFocus X7 — Default Setting diagram (page 26)
Fig. 21 · Default Setting

Mute: Choose “On” to mute the volume. Choose “Off” to restore the volume. Volume: Press the to decrease the volume. Press the to increase the volume. Lamp Reset Reset the lamp life hour after replacing a new lamp.

Reset Return the adjustments and settings to the factory default values.

InFocus X7 — Default Setting diagram (page 26)
Fig. 22 · Default Setting

Audio

Page 27 of the InFocus X7 user manual — Language
Page 27 · click to enlarge
Page 27
InFocus X7 — Language diagram (page 27)
Fig. 23 · Language

Language

Choose the multilingual OSD menu. Press into the sub menu and then use the or or or key to select your preferred language. Press “Enter” to finalize the selection.

Language

Page 28 of the InFocus X7 user manual — Information
Page 28 · click to enlarge
Page 28
InFocus X7 — Information diagram (page 28)
Fig. 24 · Information

Information

Information To display the projector information on the screen.

Page 29 of the InFocus X7 user manual — Problem: Partial, scrolling or incorrectly displayed image
Page 29 · click to enlarge
Page 29

Appendices

Troubleshooting If you experience trouble with the projector, refer to the fol lowing information. If the problem persists, please contact your local dealer or service center.

Problem: No image appears on screen

Ensure all the cables and power connections are correctly and

securely connected as described in the “Operation” section.

Ensure the pins of connectors are not crooked or broken.

Check if the projection lamp has been securely installed. Please

refer to the “Replacing the lamp” section.

Make sure you have removed the lens cap and the projector is

switched on.

Problem: Partial, scrolling or incorrectly displayed image

Press “Re-Sync” on the remote control.

If you are using a PC:

For Windows 3.x:

1. In the Windows Program Manager, double click the “Windows

Setup” icon in the Main group.

2. Verify that your display resolution setting is less than or equal

to 1280 x 1024.

For Windows 95, 98, 2000, XP:

1. From the “My Computer” icon, open the “Control Panel” folder,

and double click the “Display” icon.

2. Select the “Settings” tab
3. Click on the “Advanced Properties” .

If the projector is still not projecting the whole image, you will

also need to change the monitor display you are using. Refer to

the following steps.

Page 30 of the InFocus X7 user manual — Problem: Image is unstable or flickering
Page 30 · click to enlarge
Page 30

Appendices

4. Verify the resolution setting is less than or equal to 1280 x 1024

resolution.

5. Select the “Change” under the “Monitor” tab .
6. Click on “Show all devices”. Next, select “Standard monitor

types” under the SP box; choose the resolution mode you need

under the “Models” box.

If you are using a Notebook:

1. First, follow the steps above to adjust resolution of the com

puter.

2. Press the toggle output settings. example: [Fn]+[F4]

Compaq=> [Fn]+[F4] Dell => [Fn]+[F8] Gateway=> [Fn]+[F4] IBM=> [Fn]+[F7] Mac Apple: System Preference-->Display-->Arrangement-->Mirror display

Hewlett => [Fn]+[F4] Packard NEC=> [Fn]+[F3] Toshiba => [Fn]+[F5]

If you experience difficulty changing resolutions or your monitor

freezes, restart all equipment including the projector.

ProblemThe screen of the Notebook or PowerBook com puter is not displaying a presentation

If you are using a Notebook PC:

Some Notebook PCs may deactivate their own screens when a

second display device is in use. Each has a different way to be

reactivated. Refer to your computer’s documentation for detailed

information.

Problem: Image is unstable or flickering

Adjust the "Tracking" to correct it. Refer to the "Image" section for

more information.

Change the monitor color setting from your computer.

Page 31 of the InFocus X7 user manual — Problem: Lamp burns out or makes a popping sound
Page 31 · click to enlarge
Page 31

Appendices

Problem: Image has vertical flickering bar Use “Frequence” to make an adjustment. Check and reconfigure the display mode of your graphic card to

make it compatible with the product.

Problem: Image is out of focus

Adjust the Focus Ring on the projector lens.

Make sure the projection screen is between the required distance

3.9 to 39.4 feet (1.2 to 12.0 meters) from the projector (refer to page

16).

Problem: The image is stretched when displaying 16:9 DVD

The projector automatically detects 16:9 DVD and adjusts the aspect

ratio by digitizing to full screen with 4:3 default setting.

If the image is still stretched, you will also need to adjust the aspect

ratio by referring to the following:

Please select 4:3 aspect ratio type on your DVD player if you are

playing a 16:9 DVD.

If you can’t select 4:3 aspect ratio type on your DVD player,

please select 4:3 aspect ratio in the on screen menu.

Problem: Image is reversed

Select “Display Setting-->Projection” from the OSD and adjust the

projection direction.

Problem: Lamp burns out or makes a popping sound

When the lamp reaches its end of life, it will burn out and may

make a loud popping sound. If this happens, the projector will

not turn on until the lamp module has been replaced. To replace

the lamp, follow the procedures in the “Replacing the Lamp”.

Page 32 of the InFocus X7 user manual — Problem: LED lighting message
Page 32 · click to enlarge
Page 32

Appendices

Problem: LED lighting message

InFocus X7 — Problem: LED lighting message diagram (page 32)
Fig. 25 · Problem: LED lighting message

Steady light => No light =>

Page 33 of the InFocus X7 user manual — Problem: Message Reminders
Page 33 · click to enlarge
Page 33

Appendices

Problem: Message Reminders

Over temperature - the projector has exceeded its recommended

operating temperature and must be allowed to cool down before it

may be used.

Replacing the lamp - the lamp is about to reach its maximum life

time. Prepare to replace it soon.

Fan failed - the system fan is not working.

Page 34 of the InFocus X7 user manual — Appendices
Page 34 · click to enlarge
Page 34

Appendices

Replacing the lamp

The projector will detect the lamp life itself. It will show

you a warning message

Only InFocus lamps are tested with this projector. Use of

other lamps may cause electrical shock and fire.

Be extremely careful when removing the lamp housing. In

the unlikely event that the bulb ruptures, small glass frag ments may be generated. The lamp housing is designed to contain these fragments, but use caution when remov ing the lamp housing. Before replacing the lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement.

Hg - Lamp contains mercury. Manage in accordance with

local disposal laws. See www.lamprecycle.org.

When you see this message, change the lamp as soon as

possible. Make sure the projector has been cooled down for at least 60 minutes before changing the lamp.

Page 35 of the InFocus X7 user manual — Appendices
Page 35 · click to enlarge
Page 35

Appendices

InFocus X7 — Appendices diagram (page 35)
Fig. 26 · Appendices

Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the Power/ Standby . 2. Allow the projector to cool down at least 60 minutes. 3. Disconnect the power cord. 4. Use a screwdriver to remove the screw from the cover. 5. Push up and remove the cover. 6. Remove the 2 screws from the lamp module and pull up

To replace the lamp module, reverse the previous steps.

Page 36 of the InFocus X7 user manual — Appendices
Page 36 · click to enlarge
Page 36

Appendices

Compatibility Modes

InFocus X7 — Appendices diagram (page 36)
Fig. 27 · Appendices

Power Mac G4 640 x 480 66.6 (67) 34.93

Page 37 of the InFocus X7 user manual — Note: “ * ” for XGA model only
Page 37 · click to enlarge
Page 37

Appendices

Modes Resolution V.Frequency

H.Frequency

640 x 480 66.6 (67) 34.93

800 x 600 60 37.90

1024 x 768 60 48.40

1152 x 870 75 68.68

*1280 x 960 75 75.00

i Mac DV (G3) 1024 x 768 75 60.00

Note: “ * ” for XGA model only

(Hz) · (kHz)

Ask about the InFocus X7

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus X7

Be the first to ask — other owners or our team will answer.

Original document

InFocus X7 manual PDF

37 pages·3.1 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…