EN
InFocus logo
Official user manual

InFocus X2

49 pages·2.5 MB·Projector·PDF·ENDEFRITNLJA
InFocus X2
Table of Contents 38 sections Introduction · Positioning the projector · Projector and Device Connector Guide · Computer connections · … ShowHide
Page 1 of the InFocus X2 user manual — USER’S GUIDE
Page 1 · click to enlarge
Page 1
InFocus X2 diagram (page 1)
Fig. 1
InFocus X2 diagram (page 1)
Fig. 2

USER’S GUIDE

X2 MULTI-USE PERFORMANCE

InFocus X2 — USER’S GUIDE diagram (page 1)
Fig. 3
Page 2 of the InFocus X2 user manual — EMC: EN 55022
Page 2 · click to enlarge
Page 2

and, if not installed and used in accordance with the instructions, may cause harmful

installation. This equipment generates, uses and can radiate radio frequency energy

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Other specific Country Approvals may apply. Please see product certification label.

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

--Connect the equipment into an outlet on a circuit different from that to which the

InFocus reserves the right to alter product offerings and specifications at any time

turning the equipment off and on, the user is encouraged to try to correct the

interference to radio communications. However, there is no guarantee that

provide reasonable protection against harmful interference in a residential

--Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

--Increase the separation between the equipment and receiver.

interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

UL, CUL, NOM, IRAM, GOST, C-tick

receiver is connected.

without notice.

Canada

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple

ManufacturerInFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon

We declare under our sole responsibility that this projector conform to the following

Computer, Inc. IBM is a trademark or registered trademark of International Business

ProjectorNet, LiteShow, and LP are trademarks or registered trademarks of InFocus

Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered

registered trademarks of Adobe Systems Incorporated. InFocus, ProjectorManager,

trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or

97070 USA European OfficeStrawinskylaan 585, 1077 XX Amsterdam, The Netherlands

Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC

EMC Directive 89/336/EEC, Amended by 93/68/EEC

This User’s Guide applies to model X2.

SafetyEN 60950: 2000

EN 61000-3-2

EN 61000-3-3

directives and norms:

EMC: EN 55022

EN 55024

Corporation.

Show 5 more labels / short text on this page
Agency Approvals · FCC Warning · Declaration of Conformity · February, 2004 · Trademarks
Page 3 of the InFocus X2 user manual — Table of Contents
Page 3 · click to enlarge
Page 3

and operating the projector, refer to this User’s Guide. Electronic versions of

If you are experienced in setting up projection systems, use the Quick Setup

card that is included with the projector. For complete details on connecting

this User’s Guide in multiple languages are available on the included CD.

The website also has technical specifications (an interactive image size cal-

product data sheet), a web store to buy accessories, and a page for online

culator, laptop activation commands, connector pin outs, a glossary, the

The most current versions can be found on our website.

registration.

Introduction 5 Positioning the projector 7 Projector and Device Connector Guide 8 Computer connections 8 Video connections 8 Connecting a computer source 11 Required computer connections 11 Optional computer connections 11 Displaying a computer source image 12 Adjusting the image 13 Using the projector with Windows 98 for the first time 14 Connecting a video device 16 Video device connections 17 Composite video connection 17 S-video connection 17 VGA connection 18 Displaying video 19 Adjusting the image 19 Shutting down the projector 21 Troubleshooting your setup 21 Using the remote control 29 Using the audio 30 Using the keypad buttons 31 Optimizing computer images 32 Presentation features 32 Optimizing video images 33 Customizing the projector 33 Using the menus 34 Picture menu 35 Settings menu 38 Maintenance 41 Cleaning the Lens 41 Replacing the Projection Lamp 41 Cleaning the Lamp Housing Screens 43 Using the security lock 43 Appendix 44 Projected Image Size 44 Red LED Behavior and Projector Errors 44

Table of Contents

Page 4 of the InFocus X2 user manual
Page 4 · click to enlarge
Page 4

Do not place objects or people in the 2 foot (.6m) area along the front of the projector.

InFocus X2 diagram (page 4)
Fig. 4
InFocus X2 diagram (page 4)
Fig. 5

For ceiling mount applications, this area should be 5 feet (1.5m).

5 ft (1.5m)

  • Locate the projector at least 4' (1.2 m) away from any heating or cooling
  • Place the projector in a horizontal position no greater than 15 degrees
  • Locate the projector in a well-ventilated area without any obstructions

to intake or exhaust vents. Do not place the projector on a tablecloth or

placed in the surrounding area and thoroughly clean the area along all

sides of the projector. Wash hands after cleaning the area and handling

warranty. For complete details of the warranty, see the Warranty section at

  • Use only the power cord provided. A surge-protected power strip is
  • In the unlikely event of the lamp rupturing, discard any edible items

Follow these instructions to help ensure image quality and lamp life over

the life of the projector. Failure to follow these instructions may affect the

the ruptured lamp. This product has a lamp which contains a very

small amount of mercury. Dispose of it as required by local, state or

  • Refer to this manual for proper startup and shutdown procedures.

federal ordinances and regulations. For more information see

other soft covering that may block the vents.

  • Use only InFocus-approved ceiling mounts.

the end of this User's Guide.

recommended.

www.eiae.org.

off axis.

vents.

Page 5 of the InFocus X2 user manual — Accessories
Page 5 · click to enlarge
Page 5
InFocus X2 — Introduction diagram (page 5)
Fig. 6 · Introduction
InFocus X2 — Introduction diagram (page 5)
Fig. 7 · Introduction

The standard accessories that came with your projector can be found on the

Your new digital projector is simple to connect, easy to use, and straightfor-

800x600 resolution and is compatible with a wide variety of computers and video devices, including:

  • Apple ® Macintosh ® and PowerBook ® computers up to 1024x768 reso-

visit our website, as specifications are subject to change. Web address infor-

included packing list. Optional accessories are listed in the Accessories cata-

log that came with the projector and can also found on our website. See the

ward to maintain. It is a versatile projector that is flexible enough for busi-

  • Most standard VCRs, DVD players (progressive and interlaced), pro-
  • IBM-compatible computers, including laptops, up to 1024x768 resolu-

announcements, and registration incentives. See the inside back cover for

gressive DVD, HDTV sources, TV and satellite tuners, camcorders,

To read the latest specifications on your multimedia projector, be sure to

ness presentations and home video viewing too. It has native SVGA

Register your projector on our website to receive product updates,

mation is located on the back inside cover of this User’s Guide.

video games, and laser disc players.

inside back cover for the Web address.

Product specifications

Online Registration

Introduction

the Web address.

Accessories

lution.

tion.

Show 15 more labels / short text on this page
adjustable foot release · power switch · power cord · connector · housing · lamp · door · keypad · speaker · foot adjustable · focus (thin ring) · remote control · receiver (IR) · connector · panel
Page 6 of the InFocus X2 user manual — Wireless Projection
Page 6 · click to enlarge
Page 6
InFocus X2 — Introduction diagram (page 6)
Fig. 8 · Introduction

to, for example, screen relay (see screen manufacturer

InFocus X2 — Introduction diagram (page 6)
Fig. 9 · Introduction
InFocus X2 — Introduction diagram (page 6)
Fig. 10 · Introduction

cable that came with your screen, when you turn on the projector the screen

Contact an authorized InFocus dealer or visit the website listed on the back

ple, if you connect your projection screen to the 12 volt DC output with the

will move down; when you turn the projector off, the screen will return to

LiteShow wireless adapter and software for cable-free digital projection.

constant output while the projector is on. It has numerous uses. For exam-

the storage position. To use the 12 volt DC output, you must first remove

12 volt DC output The 3.5mm mini-jack trigger provides a 12 volt DC output. It provides a

The projector provides both computer and video connection options,

the safety plug and turn Screen Trigger on in the System menu (see

You can use the projector’s M1 connector along with the InFocus

inside cover of this User’s Guide for more information.

The projector also provides the following connectors:

  • Composite RCA audio/video
  • 12 volt DC output (see below)
  • M1 for computer and video

Wireless Projection

Connector Panel

  • Monitor out
  • Audio out

including:

  • S-video

page 38).

M1computer monitor S-video · DC output out · for details)

Page 7 of the InFocus X2 user manual — Positioning the projector
Page 7 · click to enlarge
Page 7
InFocus X2 — Positioning the projector diagram (page 7)
Fig. 11 · Positioning the projector
InFocus X2 — Positioning the projector diagram (page 7)
Fig. 12 · Positioning the projector
InFocus X2 — Positioning the projector diagram (page 7)
Fig. 13 · Positioning the projector

1.22 ft above center

3.29 ft above center

10 ft high image

10 ft high image

To determine where to position the projector, consider the size and shape of

  • Position the projector on a flat surface at a right angle to the screen. The

sion cables). To ensure adequate cable access, do not place the projector

turn the image upside down, see “Ceiling” on page 38. We recommend

  • Position the projector the desired distance from the screen. The distance

112.2% when the projector is in 4:3 mode (default mode). This means that if you have an image 10’ high, the bottom of the image will be 1.22’

  • See “Connecting a video device” on page 16 for additional information

the projector and the rest of your equipment. Here are some general guide-

  • If you are installing the projector on the ceiling, refer to the installation

guide that comes with the Ceiling Mount Kit for more information. To

means that if you have an image 10’ high, the bottom of the image will

your screen, the location of your power outlets, and the distance between

within 6 feet (1.8m) of your video device (unless you purchase exten-

from the lens of the projector to the screen, the zoom setting, and the

video format determine the size of the projected image. The top illus-

tration to the right shows three projected image sizes. For more infor-

mation about image sizes at different distances, see “Projected Image

projector must be at least 4.9 feet (1.49m) from the projection screen.

  • Position the projector within 10 feet (3m) of your power source and
  • This image offset is 132.9% when the projector is in 16:9 mode. This
  • The image exits the projector at a given angle. This image offset is

within 6 inches (.15m) of a wall or other object.

be 3.29’ above the center of the lens.

Positioning the projector

using an authorized ceiling mount.

above the center of the lens.

on 16:9 and 4:3 modes.

Size” on page 44.

lines:

Show 4 more labels / short text on this page
bottom of image · bottom of image · of lens · of lens
Page 8 of the InFocus X2 user manual — Computer connections
Page 8 · click to enlarge
Page 8

The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as com-

puters, standard VCRs, DVD players (progressive and interlaced), HDTV sources (1080i, 1035i, and 720p HDTV formats), TV and satellite tuners, camcord-

Computer In input on the projector. The USB part of the computer cable allows you to advance slides in a PowerPoint™ presentation via a remote control.

The first step for connecting video is deciding what type of output connector you want to connect to the projector. If there is more than one output on your

able as an optional accessory) to connect a progressive source’s component connectors to the projector. The S-video port does not function with progressive

Computer connections involve attaching the VGA and USB ends of the provided computer cable to a computer and connecting the other end (M1) to the

HDTV and progressive sources should only be handled through the projector’s computer connector. You can also use an M1 to Component adapter (avail-

If you are connecting the projector to HDTV sources, the projector’s M1 computer connector, labeled Computer In, should be used. Keep in mind that

video device, select the one with the highest quality. Your options are S-video (higher quality) and Composite video (lesser quality).

InFocus X2 — Projector and Device Connector Guide diagram (page 8)
Fig. 14 · Projector and Device Connector Guide

ers, video games (progressive and interlaced), and laser disc players.

Projector and Device Connector Guide

See page 11 for computer/projector setup information.

Computer connections

Video connections

sources.

Show 5 more labels / short text on this page
audio/visual · (composite) · progressive · sources) · projector input connectors
Page 9 of the InFocus X2 user manual — Projector and Device Connector Guide
Page 9 · click to enlarge
Page 9
InFocus X2 — Projector and Device Connector Guide diagram (page 9)
Fig. 15 · Projector and Device Connector Guide
Video DeviceVideo CompatibilityIf Your Device Connector IsAttach to Adapter or Labeled Connector on ProjectorFor Setup Instructions, seeComments Standard Broadcast TV (not HDTV) via: cable, digital cable, satellite TV, DVD, or VCRNTSC, PAL, and SECAM formatsComposite video or S-videoComposite video or S-videoComposite video connection on page 17. S-video connection on page 17Not for progressive (i.e. HDTV) sources. See page 10. Standard Video CameraNTSC, PAL, and SECAM formatsComposite video or S-videoComposite video or S-videoComposite video connection on page 17. S-video connection on page 17Not for progressive (i.e. HDTV) sources. See page 10. Standard Video GameNTSC, PAL, and SECAM formatsComposite video or S-videoComposite video or S-videoComposite video connection on page 17. S-video connection on page 17Not for progressive (i.e. HDTV) sources. See page 10.

Compatibility If Your Device

Video Device Video

Page 10 of the InFocus X2 user manual — HDTV
Page 10 · click to enlarge
Page 10
InFocus X2 — Projector and Device Connector Guide diagram (page 10)
Fig. 16 · Projector and Device Connector Guide
Video DeviceVideo CompatibilityIf Your Device Connector IsAttach to Adapter or Labeled Connector on ProjectorFor Setup Instructions, seeComments HDTV (High Definition TV)1080i, 720pVGA Component videoComputer In Computer In via optional M1 to Component adapterVGA connection on page 18 M1 to Component adapter on page 18Not for Component 480i. Progressive DVD1080i, 720p Component 480pVGA Component videoComputer In Computer In via optional M1 to Component adapterVGA connection on page 18 M1 to Component adapter on page 18Not for Component 480i.

Compatibility If Your Device

HDTV

Show 4 more labels / short text on this page
Video Device Video · Progressive Video Game · (High Definition TV) · Progressive DVD
Page 11 of the InFocus X2 user manual — Connecting a computer source
Page 11 · click to enlarge
Page 11
InFocus X2 — Connecting a computer source diagram (page 11)
Fig. 17 · Connecting a computer source
InFocus X2 — Connecting a computer source diagram (page 11)
Fig. 18 · Connecting a computer source

Connect the other ends (USB and VESA) to the USB and VGA ports on your

computer. If you are using a desktop computer, you will need to disconnect

computer screen as well as on the projection screen, connect the computer’s

ing video devices) to the blue M1 Computer In connector on the projector.

This connection allows you to advance slides in a PowerPoint presentation

Connect the black power cord to the Power connector on the side of the pro-

included) to your computer and to the red and/or white Audio In connec-

Connect one end of the provided computer cable (see page 16 for connect-

using the remote. USB drivers must be installed to use the USB feature.

If you are using a desktop computer and want to see the image on your

To have sound with your presentation, connect an audio cable (not

monitor cable to the Monitor Out connector on the projector.

the monitor cable from the computer’s video port first.

Connecting a computer source

Optional computer connections

Required computer connections

For more information, see page 15.

jector and to your electrical outlet.

tors on the projector.

Show 4 more labels / short text on this page
connect computer cable · connect power cable · connect monitor cable · connect audio cable
Page 12 of the InFocus X2 user manual — Displaying a computer source image
Page 12 · click to enlarge
Page 12
InFocus X2 — Displaying a computer source image diagram (page 12)
Fig. 19 · Displaying a computer source image
InFocus X2 — Displaying a computer source image diagram (page 12)
Fig. 20 · Displaying a computer source image

activate laptop’s external port

Many laptops do not automatically turn on their external video port when a

projector is connected. Usually a key combination like FN + F8 or CRT/LCD

The LED flashes green and the fans start to run. When the lamp comes on,

The computer’s image should appear on the projection screen. If it doesn’t,

If your computer has Windows 98 as its operating system, see “Using the

labeled function key simultaneously. Refer to your laptop’s documenta-

? No laptop image? Try pressing the Auto Image button on the key-

key turns the external display on and off. Locate a function key labeled

Toggle the Power switch on the side of the projector to the On position.

projector with Windows 98 for the first time” on page 14 regarding the

CRT/LCD or a function key with a monitor symbol. Press FN and the

the start up screen displays and the LED is steady green. It can take a

Displaying a computer source image

press the Computer button on the projector’s keypad.

Make sure your laptop’s external video port is active.

minute for the image to achieve full brightness.

? No start up screen? Get help on page 21.

tion to learn your laptop’s key combination.

pad. Get help on page 22.

Turn on your computer.

Remove the lens cap.

driver setup process.

Show 6 more labels / short text on this page
or LCD/CRT key · monitor key · FN key · toggle Power switch · turn on computer · remove lens cap
Page 13 of the InFocus X2 user manual — Adjusting the image
Page 13 · click to enlarge
Page 13
InFocus X2 — Adjusting the image diagram (page 13)
Fig. 21 · Adjusting the image

adjust zoom or focus

If necessary, adjust the height of the projector by pressing the release button

Avoid placing your hands near the hot exhaust vent in front of the projector.

If the image is not square, adjust the keystone using the buttons on the key-

Position the projector the desired distance from the screen at a 90 degree

Press the top Keystone button to reduce the upper part of the image, and

If necessary, rotate the leveling foot located at the rear of the projector.

press the bottom Keystone button to reduce the lower part.

See page 44 for a table listing screen sizes and distances.

Adjust the Contrast or Brightness in the Picture menu.

See page 35 for help with these menu adjustments.

Adjusting the image

Adjust the zoom or focus.

to extend the foot.

angle to the screen.

pad.

Show 11 more labels / short text on this page
rotate · leveling · foot · release button · focus · adjust Picture menu · elevator · adjust distance · adjust keystone · adjust height · foot
Page 14 of the InFocus X2 user manual — time
Page 14 · click to enlarge
Page 14
InFocus X2 — Using the projector with Windows 98 for the first time diagram (page 14)
Fig. 22 · Using the projector with Windows 98 for the first ti…
InFocus X2 — Using the projector with Windows 98 for the first time diagram (page 14)
Fig. 23 · Using the projector with Windows 98 for the first ti…
InFocus X2 — Using the projector with Windows 98 for the first time diagram (page 14)
Fig. 24 · Using the projector with Windows 98 for the first ti…

The first time you connect a computer running Windows 98 to the projector,

locates the driver. If this driver has been removed, reload the driver using

If you are running Windows 2000 or Windows ME, skip these steps and go

New Hardware Wizard appears. Follow these instructions to use the Wiz-

d When Windows finds the driver, you are ready to install it. Click Next.

the computer recognizes the projector as “new hardware” and the Add

c Uncheck any checked boxes, then click Next. Windows automatically

Using the projector with Windows 98 for the first

ard to load the correct driver (which was installed with your Windows

b Make sure “Search for the best driver” is selected, then click Next.

a Click Next to begin searching for the driver.

your Windows operating system CD.

to “Adjusting the image” on page 13.

operating system).

time

a · b · d

Page 15 of the InFocus X2 user manual — Skip this page if you did not connect a USB mouse cable
Page 15 · click to enlarge
Page 15

appears again. Drivers must be installed to use the USB functionality.

The second time a USB Human Interface Device (for the keyboard).

  • If you connected the USB cable, the Add New Hardware Wizard

The third time it detects a USB Human Interface Device (for the

Skip this page if you did not connect a USB mouse cable

For Windows 2000, Windows ME, and Windows XP:

The first time it detects a USB Composite Device.

  • The USB drivers are automatically installed.
  • The Wizard launches three times .

For Windows 98:

mouse).

Page 16 of the InFocus X2 user manual — What is Aspect Ratio?
Page 16 · click to enlarge
Page 16

(NTSC

16:9 mode

InFocus X2 — (NTSC diagram (page 16)
Fig. 25

4:3 screen 16:9 screen

digital cameras, video game consoles, HDTV receivers, and TV tuners to the

ples of tuners are digital cable boxes, VCRs, digital video recorders, and sat-

ellite TV boxes. Basically, any device that can change channels is considered

Before connecting your projector, you should decide which aspect ratio you

are 16:9. If you’re projecting onto a screen, the size/shape of the screen may

determine which aspect ratio to use. If you are projecting onto a blank wall,

you don’t have the screen size restriction. What you plan to project will also

direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies

the built-in speaker, or you can connect the audio to your stereo system via

You can connect the projector to most video devices that can output video.

You cannot directly connect the coaxial cable that enters your house from a

cable or satellite company, the signal must pass through a tuner first. Exam-

Aspect ratio is the ratio of the image width to image height. TV screens are

anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3

only appear correctly if the DVD player is set to output to a 16:9 television.

projector. There is also an audio input via the red and white A/V connec-

tors. You can connect the audio directly to the projector to get sound from

usually 4:3, which is the default for this projector. HDTV and most DVDs

help you choose between 4:3 and 16:9. Most TV shows are 4:3, while most

screen you should still use 16:9 for anamorphic movies or HDTV, but you

You can connect video devices such as VCRs, DVD players, camcorders,

want to use. The projector’s Aspect Ratio setting is accessed through the

also have the option of using either 4:3 (to fill the screen) or Native (for

If a have a 16:9 screen then you should select an aspect ratio of 16:9 for

projector’s Picture Menu. See page 35 for more information.

Connecting a video device

What is Aspect Ratio?

the Audio Out connector.

movies are 16:9.

a tuner.

Native · mode · only)

Page 17 of the InFocus X2 user manual — S-video connection
Page 17 · click to enlarge
Page 17
InFocus X2 — Video device connections diagram (page 17)
Fig. 26 · Video device connections
InFocus X2 — Video device connections diagram (page 17)
Fig. 27 · Video device connections

connect S-video and A/V cables

Plug a white connector into the left audio out connector on the video device

Keep in mind that video output from composite connections are not as high

S-video cable (available as an optional accessory) into the S-video connector

the A/V cable’s red and white audio connectors as described directly above

Plug the provided A/V cable’s yellow connector into the video-out connec-

device. Plug the remaining white connector into the white audio in connec-

If your video device uses a round, seven-prong S-video connector, plug an

on your video device and into the S-video connector on the projector. Use

and plug a red connector into the right audio out connector on the video

Keep in mind that S-video delivers higher quality video output than com-

tor on the video device. Plug the other yellow connector into the yellow

tor on the projector, and plug the remaining red connector into the red

(the yellow connectors on the A/V cable are not used).

Video device connections

Composite video connection

Video 2 connector on the projector.

audio in connector on the projector.

S-video connection

quality as S-video.

posite.

connect A/V cable

Page 18 of the InFocus X2 user manual — VGA connection
Page 18 · click to enlarge
Page 18
InFocus X2 — VGA connection diagram (page 18)
Fig. 28 · VGA connection
InFocus X2 — VGA connection diagram (page 18)
Fig. 29 · VGA connection
InFocus X2 — VGA connection diagram (page 18)
Fig. 30 · VGA connection

If your video device has a 15-pin VGA output, plug one end of the included

tor may be labeled “To Monitor” on the video source. Plug the M1 computer

To connect a progressive scan DVD or HD source, use an M1 to Component

computer cable into the VGA connector on your video source. This connec-

Connect the power cord to the Power connector on the side of the projector

end of the cable into the Computer In connector on the projector. Do not

Use the A/V cable’s red and white audio connectors as described on the

adapter (available as an optional accessory). Connect one end of a compo-

nent cable (not provided) into the adapter. Connect the M1 end of the

previous page (the yellow connectors on the A/V cable are not used).

adapter into the Computer 1 connector on the projector.

plug the USB end of this cable into the video device.

M1 to Component adapter

and to your electrical outlet.

VGA connection

connect computer and · connect power cable · A/V cables

Page 19 of the InFocus X2 user manual — Adjusting the image
Page 19 · click to enlarge
Page 19

turn on video device

The LED flashes green and the fans start to run. When the lamp comes on,

the start-up screen is displayed and the LED is steady green. It can take a

Adjust the height of the projector by pressing the release button to extend

Position the projector the desired distance from the screen at a 90 degree

Toggle the Power switch on the side of the projector to the On position.

The video device’s image should appear on the projection screen. If it

? No image? Try pressing the Source or Auto Image Get help on

See page 44 for a table listing screen sizes and distances to the screen.

Rotate the leveling foot at the rear of the projector, if necessary.

minute for the image to achieve full brightness.

? No start up screen? Get help on page 22.

doesn’t, press the Video button on the keypad.

Plug in and turn on your video device.

Adjusting the image

Displaying video

Remove the lens cap.

angle to the screen.

page 22.

the foot.

Show 10 more labels / short text on this page
rotate · leveling · foot · release button · toggle Power switch · adjust distance · remove lens cap · elevator · adjust height · foot
Page 20 of the InFocus X2 user manual — Displaying video
Page 20 · click to enlarge
Page 20
InFocus X2 — Displaying video diagram (page 20)
Fig. 31 · Displaying video
InFocus X2 — Displaying video diagram (page 20)
Fig. 32 · Displaying video

adjust Picture menu options

adjust zoom and focus

If the image is not square, adjust the keystone using the buttons on the key-

pad. Press the top Keystone button to reduce the upper part of the image,

Adjust the Contrast, Brightness, Color, Tint, or Aspect Ratio in the Picture

For Aspect Ratio, keep in mind that DVD players must be configured for

16:9 in order to view the highest quality image. For more information regarding Aspect Ratio, see page 16.

menu. See page 35 for help with the menus and these adjustments.

and press the bottom Keystone button to reduce the lower part.

Adjust the volume on the keypad or remote.

Adjust the zoom and focus.

Show 4 more labels / short text on this page
focus · including Aspect Ratio · adjust keystone · adjust volume
Page 21 of the InFocus X2 user manual — Screen Save
Page 21 · click to enlarge
Page 21
InFocus X2 — Shutting down the projector diagram (page 21)
Fig. 33 · Shutting down the projector

The following tables show common problems. In some cases, more than one

If your image appears correctly on the screen, skip to the next section. If it

The LED on top of the projector indicates the state of the projector and can

sented. When the problem is solved, you can skip the additional solutions.

solid green The power switch has been toggled on

blinking green The power switch has been toggled on

possible solution is provided. Try the solutions in the order they are pre-

Table 1: LED behavior and meaning

Troubleshooting your setup

does not, troubleshoot the setup.

help you troubleshoot.

You can turn the projector off simply by toggling the power switch to the off

LED is blinking green, the projector does not accept any keypad and remote

down to minimal speed. To turn off the projector, toggle the power switch to

erly cool. However, if the remote was used to power the projector to the Off

The projector automatically displays a black screen after no active source is

detected for 30 minutes. This black screen helps preserve the life of the pro-

You can make the black screen appear after a preset number of minutes by

the projector is performed for 20 minutes. By default, this feature is off. See

Off state while it is running. When the Power button is pressed twice (once

to start the power-down process and a second time to verify that you want

to power the projector off), the lamp turns off and the LED blinks green for

minute before turning the projector on again. This allows the lamp to prop-

jector. The image returns when an active source is detected or a remote or

lamp off after no active sources are detected and no user interaction with

You can also press the remote’s Power button to place the projector in the

one (1) minute while the fans continue to run to cool the lamp. While the

The projector also has a Power Save feature that automatically turns the

When the lamp has cooled, the LED lights solid green and the fans slow

turning on the Screen Save feature in the Settings>System menu. See

state you do not need to wait one minute to turn it on again.

Shutting down the projector

Turning off the projector

keypad button is pressed.

the off position.

Screen Save

Power Save

control input.

page 38.

page 38.

position.

Page 22 of the InFocus X2 user manual — A
Page 22 · click to enlarge
Page 22
InFocus X2 — Shutting down the projector diagram (page 22)
Fig. 34 · Shutting down the projector

no start up screen plug power cord in projector’s left side

only start up screen appears press the Computer button

A

Show 5 more labels / short text on this page
Problem Solution Result · remove lens cap · restart laptop · Startup · Screen
Page 23 of the InFocus X2 user manual — A
Page 23 · click to enlarge
Page 23
InFocus X2 — Shutting down the projector diagram (page 23)
Fig. 35 · Shutting down the projector

range” press the Auto Image button on keypad computer image projected

Desktop icons Disable “Extend my Windows Desktop” in

no computer image, just the words “Signal out of

Only my laptop’s background appears, not the

A

A

A

Signal out of · range

Page 24 of the InFocus X2 user manual — A A A
Page 24 · click to enlarge
Page 24
InFocus X2 — Shutting down the projector diagram (page 24)
Fig. 36 · Shutting down the projector
InFocus X2 — Shutting down the projector diagram (page 24)
Fig. 37 · Shutting down the projector

image fuzzy or cropped set your computer’s display resolution to

A A A

image not centered on screen

Page 25 of the InFocus X2 user manual — Picture>Aspect ratio menu correct image A B A B
Page 25 · click to enlarge
Page 25

A B

Picture>Advanced menu correct image

Picture>Aspect ratio menu correct image A B A B

image not square adjust Keystone on keypad square image

image not sharp adjust Sharpness (video sources only) in the

InFocus X2 — Picture>Aspect ratio menu correct image A B A B diagram (page 25)
Fig. 38 · Picture>Aspect ratio menu correct image A B A B
InFocus X2 — Picture>Aspect ratio menu correct image A B A B diagram (page 25)
Fig. 39 · Picture>Aspect ratio menu correct image A B A B

image does not fit 4:3 or 16:9 screen change aspect ratio to 4:3 or 16:9 in

InFocus X2 — Picture>Aspect ratio menu correct image A B A B diagram (page 25)
Fig. 40 · Picture>Aspect ratio menu correct image A B A B

Problem Solution Result

Page 26 of the InFocus X2 user manual — COLOR
Page 26 · click to enlarge
Page 26

COLOR

A B

A B

image upside down turn off ceiling in Settings>System menu correct image

image reversed left to right turn off rear in Settings>System menu correct image

brightness, contrast in the menus correct image

projected colors don’t match source adjust color, tint, color temperature,

InFocus X2 — COLOR diagram (page 26)
Fig. 41
InFocus X2 — COLOR diagram (page 26)
Fig. 42

COLOR

A B

A

Problem Solution Result

Page 27 of the InFocus X2 user manual — LED
Page 27 · click to enlarge
Page 27
InFocus X2 — Shutting down the projector diagram (page 27)
Fig. 43 · Shutting down the projector
InFocus X2 — Shutting down the projector diagram (page 27)
Fig. 44 · Shutting down the projector

laptop Embedded video plays correctly

minute lamp turns on

make sure vents aren’t blocked, turn off the

presentation does not play on the screen turn off the internal LCD display on your

projector and allow it to cool for one

A B

The video embedded in my PowerPoint

lamp won’t turn on, LED blinking red

A B

LED

Problem Solution Result

Page 28 of the InFocus X2 user manual — LED
Page 28 · click to enlarge
Page 28
InFocus X2 — Shutting down the projector diagram (page 28)
Fig. 45 · Shutting down the projector

lamp must be replaced (see page 41)

If you need assistance, visit our website or call us. See the inside of the back

cover for support contact information. This product is backed by a limited

warranty. An extended warranty plan may be purchased from your dealer.

When sending the projector in for repair, we recommend shipping the unit

in its original packing material, or having a professional packaging com-

pany pack the unit. Please insure your shipment for its full value.

“Change lamp” message appears at startup or lamp

won’t turn on and LED blinking red

LED

Show 4 more labels / short text on this page
lamp turns on · Problem Solution Result · replace lamp · Still need assistance?
Page 29 of the InFocus X2 user manual — Using the remote control
Page 29 · click to enlarge
Page 29
  • Make sure you’re pointing the remote at the projector or the screen, not
  • Make sure the batteries are installed in the proper orientation and are

cable is connected. If using a USB cable, make sure the correct drivers

the computer, and are within the remote range of 15 feet (4.5m). For

  • If you are trying to advance PowerPoint slides, make sure the USB
InFocus X2 — Using the remote control diagram (page 29)
Fig. 46 · Using the remote control

best results, point the remote at the screen.

are installed.

not dead.

to display a blank screen instead of the current slide (you can choose which

Previous and Next buttons allow you to navigate through your PowerPoint

provided computer cable to your computer to use these buttons. When you

The remote uses two (2) provided AA batteries. They are easily installed by

sliding the cover off the remote’s back, aligning the + and - ends of the bat-

remote. When disposing of the batteries, be sure to do so in an environmen-

To operate, point the remote at the projection screen or at the projector (not

switch is in the Off position does not cause the projector to power up. You

need to put the projector’s Power toggle switch in the On position to let the

When the projector is running, you can press the remote’s Power button to

Press the remote’s Menu button to open the projector’s menu system. Use

the arrow buttons to navigate, and the Select button to select features and

Two presentation-specific features are also provided. Use the Blank button

color is displayed, see page 39); use the Effect button to invoke a user-defin-

presentation while in Slide Show mode. Connect the USB connector on the

than the type provided with the projector may risk severe damage to the

at the computer). The range of optimum operation is about 15 feet (4.5m).

The remote also has Volume and Mute buttons to control the sound, and

able action, such as freeze, or change your aspect ratio for viewing DVDs

do this for the first time, the Add New Hardware wizard may appear. See

Pressing the remote’s Power button when the projector’s Power toggle

place the projector in the Off state (see page 21 for shutdown info) and

adjust values in the menus. See page 34 for more info on the menus.

teries, sliding them into place, and then replacing the cover.

Video and Computer buttons to switch between sources.

page 15 for details on loading the correct USB drivers.

(see page 39 to learn to program this button).

Using the remote control

remote power on the projector.

tally proper manner.

power it off.

Troubleshooting the remote

Page 30 of the InFocus X2 user manual — Using the audio
Page 30 · click to enlarge
Page 30
InFocus X2 — Using the audio diagram (page 30)
Fig. 47 · Using the audio

with own power source

power source by plugging a speaker cable (not included) into the projector’s

To use the projector’s speaker, connect your source to the Audio In connec-

  • Make sure the volume is turned up enough. Press the Volume button

To adjust the volume, press the Volume buttons on the keypad or remote.

  • Make sure mute is not active (press the Mute button on the remote).

The projector can be attached to external speakers that have their own

  • If playing a video, make sure the playback has not been paused.

tors (L and/or R) on the projector’s composite connectors.

To mute the sound, press the Mute button on the remote.

If you aren’t hearing the audio, check the following:

  • Make sure the audio cable is connected.
  • Make sure the correct source is active.

Using the projector’s speakers

Connecting external speakers

on the keypad or remote.

  • Adjust the audio source.

Using the audio

Audio Out connector.

Show 6 more labels / short text on this page
audio out · cable · external speakers · connect audio cable · adjust volume · Troubleshooting Audio
Page 31 of the InFocus X2 user manual — Using the keypad buttons
Page 31 · click to enlarge
Page 31
InFocus X2 — Using the keypad buttons diagram (page 31)
Fig. 48 · Using the keypad buttons

Up/Down arrows–navigates to and adjusts settings in the menus (page 34).

Most buttons are described in detail in other sections, but here is an over-

Presets–cycles through the available preset settings (page 36).

Select–confirms choices made in the menus (page 34).

Keystone–adjusts squareness of the image (page 13).

Video and Computer–changes the active source.

Auto Image–resets the projector to the source.

Menu–opens the on-screen menus (page 34).

Using the keypad buttons

Volume–adjusts sound (page 30).

view of their functions:

menu navigation · buttons

Page 32 of the InFocus X2 user manual — Optimizing computer images
Page 32 · click to enlarge
Page 32

Several features are provided to make giving presentations easier. Here is an

  • The Effect button on the remote allows you to assign various features to

page 39 for details. The freeze effect allows you to freeze the displayed

  • The Startup Logo option lets you change the default start up screen to a

instead of the active source. You can determine the color of this screen

cally shut down the projector after several minutes of inactivity or dis-

about the projector and current source. You can select among Blank,

image. This is useful if you want to make changes on your computer

  • The Blank button on the remote allows you to display a blank screen
  • Two options, Power Save and Screen Save, are provided to automati-

the button. The default effect is About, which displays information

Mute, Aspect Ratio, Source, Auto Image, Freeze, and About. See

play a black screen. This helps preserve lamp life (page 38).

overview, details are found in the menu section.

without your audience seeing them.

blank or default screen (page 39).

Presentation features

(page 39).

After your computer is connected properly and the computer’s image is on

the screen, you can optimize the image using the onscreen menus. For gen-

save the settings using Presets. This allows you to quickly recall these

  • Change the Aspect Ratio. Choose the option that best fits your input
  • Once you have optimized the image for a particular source, you can
  • Adjust the Phase, Tracking, or Horizontal or Vertical position in the
  • Adjust the Keystone, Contrast, or Brightness in the Picture menu
  • Adjust the Color Temperature in the Advanced menu (page 37).

eral information on using the menus, see page 34.

Optimizing computer images

Advanced menu (page 37).

settings later (page 36).

source (page 35).

(page 35).

Page 33 of the InFocus X2 user manual — Optimizing video images
Page 33 · click to enlarge
Page 33
  • Specify which source the projector checks first for active video during
  • For rear projection, turn rear mode on in the Settings>System menu.

You can customize the projector for your specific setup and needs. See

  • For ceiling mounted projection, turn ceiling mode on in the Set-
  • Specify the function of the Effect button on the remote.
  • Turn the projector’s display messages on and off.
  • Specify blank screen colors and start up logos.
  • Save settings for the active source as a preset.

page 38 to page 40 for details on these features.

  • Specify the language viewed on the menus.

Customizing the projector

  • Turn on power saving features.

tings>System menu.

power-up.

screen, you can optimize the image using the onscreen menus. For general

  • Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
  • The remote’s Effect button allows you to assign various features to the

button. The default effect is About, which displays information about

Aspect Ratio, Source, Auto Image, Freeze, and About. See page 39 for

  • Change the Aspect Ratio. Choose the option that best fits your input

the projector and current source. You can select among Blank, Mute,

  • Adjust the Color Temperature. Select a listed warmth value (page 37).

After your video device is connected properly and the image is on the

  • Turn on Overscan to remove noise on the edges of the image.
  • Use the Color Control to adjust the color gain (page 37).

information on using the menus, see page 34.

Optimizing video images

  • Select a Sharpness setting (page 37).

source (page 35).

menu (page 35).

details.

Page 34 of the InFocus X2 user manual — Using the menus
Page 34 · click to enlarge
Page 34

keypad navigation Main menu

InFocus X2 — Using the menus diagram (page 34)
Fig. 49 · Using the menus
InFocus X2 — Using the menus diagram (page 34)
Fig. 50 · Using the menus
InFocus X2 — Using the menus diagram (page 34)
Fig. 51 · Using the menus
InFocus X2 — Using the menus diagram (page 34)
Fig. 52 · Using the menus

tons, or turn the feature on or off using check boxes. Press Select to confirm

adjustments are complete, navigate to Previous or Exit, then press Select to

  • The About menu provides a read-only display of information about the

Certain menu items may not be visible or may be grayed depending upon a

particular source being connected. For example, Sharpness is only available

for video sources and is not visible when a computer source is active. Menu

options are grayed out only if the source if selected but no signal is present.

For example, if the projector is set to a video source but the source, such as a

menus automatically close after 60 seconds if no buttons are pressed.) The

Main menu appears. Use the arrow buttons to move up and down to high-

level, ranging from one (the Main menu) to four (the most nested menus).

To open the menus, press the Menu button on the keypad or remote. (The

down arrow buttons to adjust the value, select an option using radio but-

Dots appears before the menu name. The number of dots indicate menu’s

To change a menu setting, highlight it, press Select, then use the up and

your changes. Use the arrows to navigate to another setting. When your

go to the previous menu; press the Menu button at any time to close the

  • The Settings menu provides set-up type adjustments that are not

DVD player, is turned off video menu options are grayed out.

light the desired submenu, then press the Select button.

  • The Picture menu provides image adjustments.

The menus are grouped by usage:

Using the menus

projector and source.

changed often.

menus.

buttons · About menu · dots

Page 35 of the InFocus X2 user manual — Picture menu
Page 35 · click to enlarge
Page 35
InFocus X2 — Picture menu diagram (page 35)
Fig. 53 · Picture menu
Keystoneadjusts the image vertically and makes a squarer image. You can
Contrastcontrols the degree of difference between the lightest and darkest

To adjust the following settings, highlight the setting, press Select, use the

up and down arrows to adjust the values, then press Select to confirm the

Color: adjusts a video image from black and white to fully saturated color.

Aspect Ratio: Aspect ratio is the ratio of the image width to image height.

Select Native to see the unmodified input with no resizing by the projector.

TV screens are usually 4:3. HDTV and most DVDs are 16:9. The default is

parts of the picture and changes the amount of black and white in the

Tintadjusts the red-green color balance in the image of NTSC video

images. The tint setting applies to NTSC video sources only.

For more information regarding Aspect Ratio, see page 16.

Select 16:9 to watch enhanced widescreen DVDs.

Brightness: changes the intensity of the image.

The color setting applies to video sources only.

also adjust keystone from the keypad.

Picture menu

changes.

image.

4:3.

Page 36 of the InFocus X2 user manual — Picture menu
Page 36 · click to enlarge
Page 36
InFocus X2 — Picture menu diagram (page 36)
Fig. 54 · Picture menu

tomize the settings for each source. The settings you customize are saved in

computer presentations, photographs, film images, and video images. Film

input is material originally captured on a video camera, like a TV show or

sporting event. You can use the preset as a starting point, then further cus-

the preset for each source. To restore the factory default settings, choose Fac-

adjust the image, select Save User in the Presets menu, then select Yes. You

input is material originally captured on a film camera, like a movie; video

There is also a user-definable preset. To set a preset for the current source,

PresetsPresets are provided that optimize the projector for displaying

can recall these settings in the future by selecting the User 1 preset.

tory Reset in the Settings>Service menu (page 40).

Settings · Save · User

Page 37 of the InFocus X2 user manual — Advanced menu
Page 37 · click to enlarge
Page 37
InFocus X2 — Picture menu diagram (page 37)
Fig. 55 · Picture menu
InFocus X2 — Picture menu diagram (page 37)
Fig. 56 · Picture menu
InFocus X2 — Picture menu diagram (page 37)
Fig. 57 · Picture menu
InFocus X2 — Picture menu diagram (page 37)
Fig. 58 · Picture menu
InFocus X2 — Picture menu diagram (page 37)
Fig. 59 · Picture menu

sources. It allows you to select a color space that has been specifically tuned

video standard options may vary depending on your region of the world.) If

look right or the image may appear “torn.” If this happens, manually select

Sharpness(video sources only) changes the clarity of the edges of a video
Color Temperaturechanges the intensity of the colors. Select a listed rela-
Color Controlallows you to individually adjust the gain (relative warmth
Video Standardwhen it is set to Auto, the projector attempts to automati-

a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-

Sync Threshold AdjustIf a hardware device, such as a DVD player, is not

determines the standard. To choose a different setting, turn off Auto, then

for the input signal. When Auto is selected, the projector automatically

choose RGB for computer sources, choose either SMPTE240, REC709 or

of the color) and the offset (the amount of black in the color) of the red,

cally pick the video standard based on the input signal it receives. (The

the projector is unable to detect the correct standard, the colors may not

Overscan: (video sources only) removes noise around the video image.

Horizontal/Vertical Position: adjusts the position of a computer source.

syncing properly with the projector, select this option to help it to sync

White Peaking: increases the brightness of whites that are near 100%.

Color SpaceThis option applies to computer and component video

The following four (4) options are for computer sources only.

Phase: adjusts the horizontal phase of a computer source.

Tracking: adjusts the vertical scan of a computer source.

REC601 for component video sources.

image. Select a sharpness setting.

when connected to the projector.

green, and blue colors.

Advanced menu

tive warmth value.

dard menu.

Color Control · Video Standard · Sharpness

Page 38 of the InFocus X2 user manual — Settings menu
Page 38 · click to enlarge
Page 38
InFocus X2 — Settings menu diagram (page 38)
Fig. 60 · Settings menu
InFocus X2 — Settings menu diagram (page 38)
Fig. 61 · Settings menu
InFocus X2 — Settings menu diagram (page 38)
Fig. 62 · Settings menu

first for active video during power-up. When the Autosource feature is On,

and Video 2 (for composite video connections) for video sources. When this

jection. Low Powertoggles between on and off. Turn it on to lower the light
quieter. Display Messagesdisplays status messages (such as “Searching” or

your computer from going into Screen Save mode. Screen Trigger turns on

the projector powers down, the image will be displayed. When Power Save

screen with a black color after no signals are detected for a preset number of

minutes. The image returns when an active source is detected or a remote or

Audioallows adjustments to Volume of the internal speaker and allows a

Power-up Source first. The source options are Computer 1 for a computer,

progressive DVD, or HDTV source, and Video 1 (for S-video connections),

Source. To display another source, you must manually select one by press-

System>Rearreverses the image so you can project from behind a translu-
cent screen. Ceilingturns the image upside down for ceiling-mounted pro-

“Mute”) in the lower-left corner of the screen. Screen Saver Off: prevents

the 12 volt DC output switch on the connector panel. Power Save: automat-

ically turns the lamp off after no signals are detected for 20 minutes. After

chime to play when starting the projector. Adjustments can also be made

SourcesPower-up Source determines which source the projector checks

10 additional minutes with no signal, the projector powers down. If an active signal is received before the projector powers down, the image will

be displayed. After an additional 10 minutes with no signal, the projector

powers down and can be toggled off. If an active signal is received before

is enabled, Screen Save is disabled. Screen Save automatically blanks the

the projector automatically finds the active source, checking the selected

output of the lamp. This also lowers the fan speed, making the projector

feature is Off, the projector defaults to the source selected in Power-up

ing the Computer or Video button on the remote or keypad.

from the projector’s keypad and the remote.

keypad button is pressed.

Settings menu

Show 4 more labels / short text on this page
Power-up · Source · Screen Save · Audio
Page 39 of the InFocus X2 user manual — Settings menu
Page 39 · click to enlarge
Page 39
InFocus X2 — Settings menu diagram (page 39)
Fig. 63 · Settings menu
  • About: the default effect. It opens a window with projector and source
Effect Keyallows you to assign a different function to the Effect button on

the remote, allowing you to quickly and easily use the effect. Highlight an

Startup Logoallows you to display a blank screen instead of the default
  • Aspect Ratio : toggles among 4:3, 16:9, and Native (see page 16 and

page 35). Set as the Effect Key, it can allow you to switch the Aspect

Blank Screendetermines what color is displayed when you press the
  • Auto Image : resets the projector to the source (page 31).

screen at startup, and when no source is detected.

effect and press Select to choose a different one.

  • Source : cycles through available sources.
  • Freeze : pauses the projected image.
  • Blank : displays an empty screen.
  • Mute : turns off all sound.

Blank button on the remote.

Ratio for DVDs.

information.

Startup Logo · Blank Screen · Effect Key

Page 40 of the InFocus X2 user manual — Settings menu
Page 40 · click to enlarge
Page 40
InFocus X2 — Settings menu diagram (page 40)
Fig. 64 · Settings menu
InFocus X2 — Settings menu diagram (page 40)
Fig. 65 · Settings menu
Lamp Resetresets the lamp hours used counter in the About menu to

Showing the About box is the default action assigned to the Effect button.

About: provides information about the projector and the active source.

Language: allows you to select a language for the onscreen display.

Service: To use these features, highlight them and press Select.

Service Code: only used by authorized service personnel.

Factory Reset: restores all settings to their default.

zero. Do this only after changing the lamp.

About menu · Service menu · Language menu

Page 41 of the InFocus X2 user manual — Cleaning the Lens
Page 41 · click to enlarge
Page 41
InFocus X2 — Maintenance diagram (page 41)
Fig. 66 · Maintenance
InFocus X2 — Maintenance diagram (page 41)
Fig. 67 · Maintenance
InFocus X2 — Maintenance diagram (page 41)
Fig. 68 · Maintenance
  • Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh

2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you don’t intend to use the projector immediately, replace the lens cap.

3 Turn the projector on its side so that the lamp door is facing you. Using a flat-blade screwdriver, gently pry the lamp door from the projector by

placing the screwdriver blade into the space between the top of the lamp

The lamp hours used timer in the About menu counts the number of hours

message “Change lamp” appears on the screen at startup. If the maximum

lamp time is exceeded, the lamp will not light. In this case, after replacing

the lamp you must reset the lamp hours by simultaneously pressing both

list for information. Use only a replacement lamp with the same type and

the lamp has been in use. Twenty hours before the lamp life expires, the

Volume buttons on the keypad and holding them for 10 seconds.

1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

2 Wait 30 minutes to allow the projector to cool thoroughly.

1 Turn off the projector and unplug the power cord.

Replacing the Projection Lamp

chemicals might scratch the lens.

rating as the original lamp.

door and the projector.

Cleaning the Lens

Maintenance

lamp door

Page 42 of the InFocus X2 user manual — WARNING :
Page 42 · click to enlarge
Page 42
InFocus X2 — Maintenance diagram (page 42)
Fig. 69 · Maintenance
InFocus X2 — Maintenance diagram (page 42)
Fig. 70 · Maintenance

10 Plug in the power cord and toggle the Power switch to turn the projector back on.

4 Loosen the two captive screws that attach the lamp housing to the pro- jector.

5 Detach the lamp connector from the projector by depressing the locking tab on the connector and lightly pulling it free.

6 Carefully remove the lamp housing. Dispose of the lamp in an environ- mentally proper manner.

8 Re-attach the lamp connector to the projector. The locking tab should engage when the connector is fully plugged in.

11 To reset the lamp hour timer, navigate to the Settings>Service menu and select Lamp Reset. See page 40 for details.

unlikely event that the bulb ruptures, small glass fragments may be

cleaning materials. Wash hands after lamp replacement. This prod-

uct has a lamp which contains a very small amount of mercury. Dis-

To avoid burns, allow the projector to cool for at least 30 minutes

ments, but use caution when removing the lamp housing. Before

Do not drop the lamp housing or touch the glass bulb! The glass

replacing the lamp, clean the lamp compartment and dispose of

Be extremely careful when removing the lamp housing. In the

generated. The lamp housing is designed to contain these frag-

pose of it as required by local, state or federal ordinances and

regulations. For more information see www.eiae.org.

7 Install the new lamp housing and tighten the screws.

may shatter and cause injury.

before you replace the lamp.

9 Replace the lamp door.

WARNING :

Show 8 more labels / short text on this page
captive screw · lamp cable · Service menu · captive screw · connector · locking tab · housing · lamp
Page 43 of the InFocus X2 user manual — Using the security lock
Page 43 · click to enlarge
Page 43
InFocus X2 — Cleaning the Lamp Housing Screens diagram (page 43)
Fig. 71 · Cleaning the Lamp Housing Screens
InFocus X2 — Cleaning the Lamp Housing Screens diagram (page 43)
Fig. 72 · Cleaning the Lamp Housing Screens

In dirty or dusty environments, the two dust filter screens in the lamp hous-

lamp operating temperature and prolongs lamp life. To maximize lamp life

2 Examine the dust filter screens on the lamp housing. If necessary, use a vacuum cleaner set on low power to clean the screens. Be careful not to

System. Refer to the information that came with the lock for instructions on

ing can become clogged, causing high temperatures and premature lamp

failure. Routine maintenance to remove dust from the screens lowers the

The projector has a security lock for use with a PC Guardian Cable Lock

disturb any internal components when cleaning the screens.

Cleaning the Lamp Housing Screens

you should clean the screen every 250 hours.

3 Replace the lamp housing and lamp door.

Using the security lock

1 Remove the lamp housing.

how to use it.

Show 4 more labels / short text on this page
(one on each · lamp housing) · side of the · lamp housing
Page 44 of the InFocus X2 user manual — Projected Image Size
Page 44 · click to enlarge
Page 44

If the projector is not functioning properly and the LED is blinking red, con-

InFocus X2 — Appendix diagram (page 44)
Fig. 73 · Appendix

jector on again. If the lamp does not strike

Five (5) blinks The projector is overheating. Check for a

between the blinking cycles. Visit our website for more details on the red

Two (2) blinks The lamp counter hours have exceeded

Three (3) blinks The projector has shut down. Check to

see if the lamp door is open. If the lamp

Four (4) blinks The fan has failed. Contact Technical Sup-

sult Table 3 to determine a possible cause. There are two-second pauses

One (1) blink The lamp won't strike after five (5)

Red LED Behavior and Projector Errors

Table 3:

LED error codes.

Range of distance to the screen for a given screen size for the projector

40/1 32/0.8 5.8/1.8 4.8/1.5 50/1.3 40/1 7.8/2.4 6,5/2.0 60/1.5 48/1.2 8.8/2.7 7.5/2.3 100/2.5 80/2 14.6/4.5 12.4/3.8 150/3.8 120/3.1 22.6/6.9 19.03/5.8 200/5.1 160/4.1 30.5/9.3 25.2/7.7

Table 2:

Projected Image Size

Appendix

Show 12 more labels / short text on this page
Minimum · Distance · (feet/m) · Distance to screen · Maximum · distance · (feet/m) · Image Width · (inches/m) · Screen Size · (inches/m) · Diagonal
Page 48 of the InFocus X2 user manual — Limited Warranty
Page 48 · click to enlarge
Page 48

ranty if the Product has been damaged due to abuse, misuse, neglect, smoke

mount), tampering, alterations, or service other than by InFocus or its autho-

Product repair outside of the terms of the Limited Warranty will be on a time

The Accessory Product Limited Warranty covers the accessory item only and

OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS.

SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG

ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PUR-

CHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER.

rized agents, causes other than from ordinary use or failure to properly use

This Limited Warranty excludes Product cleaning, repair, or replacement of

Product wear and is not considered normal use under the terms of this Lim-

Remanufactured Products and Software Products are exempt from the fore-

Product Limited Warranty or Software Product Limited Warranty for appli-

THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED

THIS WARRANTY SETS FORTH INFOCUS’ MAXIMUM LIABILITY FOR

InFocus shall have no further obligation under the foregoing Limited War-

and materials basis. Prolonged Product “demonstration” causes unusual

going Limited Warranty. Please refer to the appropriate Remanufactured

THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI-

CABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR

EXTEND BEYOND THE DISCRITPTION ON THE FACE HEREOF AND

exposure (cigarette or otherwise), accident, unusual physical or electrical

plastics due to cosmetic damage and damage as a result of normal wear.

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-

RANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR

PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT

excludes normal wear. The Lamp Product Limited Warranty excludes

stress, unauthorized modifications (including use of an unauthorized

the Product in the application for which said Product was intended.

WARRANTY LIMITATION AND EXCLUSION

DISCLAIMER OF UNSTATED WARRANTIES

cable Warranty information.

expected lamp degradation.

ited Warranty.

(hereinafter collectively or individually referred to as “Product” as appropri-

If the Product while subject to this Limited Warranty, is defective in material

or workmanship during the warranty period, then InFocus, at its option, will

All exchanged parts and Products replaced under this Limited Warranty will

for) all labor necessary to repair the Product found to be defective within the

Projector proof of purchase, whichever comes first. Replacement Lamps

purchased at the time of Projector Product purchase will have a 90-day

usage Limited Warranty Period from the date of replacement lamp pur-

  • Accessory Product Limited Warranty Period: One (1) Year from date of

Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Cor-

ate) purchased from InFocus, an InFocus distributor, or an InFocus reseller

will conform to InFocus’ specifications and be free from defects in material

Limited Warranty period and to repair or replace defective parts with new

parts or, at the option of InFocus, serviceable used parts that are equivalent

or superior to new parts performance. Limited Warranty periods are as fol-

  • Projector Product Limited Warranty Period (Excluding Lamps): One
  • Lamp Product Limited Warranty Periods: The original installed lamp

shall have a 90-day or 500 hour Limited Warranty Period from date of

poration (“InFocus”) warrants that the Projector, Lamps and Accessories

become property of InFocus. InFocus’ sole obligation is to supply (or pay

or 500 hours usage Limited Warranty Period from the date of installa-

tion, whichever comes first. Replacement lamps purchased after the

below. InFocus does not warrant that the Product will meet the specific

time of Projector Product purchase shall have a 90-day or 500 hours

or workmanship for the respective Limited Warranty period provided

requirements of the end-user customer.

REPAIR or REPLACE the Product.

(1) Year from date of purchase.

chase, whichever comes first.

Limited Warranty

purchase.

lows:

Page 49 of the InFocus X2 user manual — Limited Warranty Period
Page 49 · click to enlarge
Page 49

place of original purchase, to the manufacturer (Purchaser must bear all tax,

No repair or replacement of Product or part thereof shall extend the Limited

NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF

ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS

rized repair center for InFocus, proof of legal import must accompany the

Warranty period as to the entire Product. Warranty on the repair part and

workmanship shall only be effective for a period of ninety (90) days follow-

THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND

CIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR

Limitation on Bringing Action - No action, regardless of form, arising out

Mandatory Arbitration – Any action, regardless of form, arising out of the

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITA-

UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPE-

Governing Law - Any action, regardless of form, arising out of the agree-

YOU MAY ALSO HAVE OTHER RIGHTS, DEPENDING ON JURISDIC-

warranty repair Product, otherwise the Product must be returned to the

ing the repair or replacement of that part or the remaining period of the

WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN

STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING

of the agreement to purchase the Product may be brought by purchaser

LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND

duty and freight), or the Purchaser must bear charges for the warranty

LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE

agreement to purchase the Product is subject to mandatory arbitration.

TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE

IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY

ment to purchase the Product is governed by Oregon law.

more than one year after the cause of action has accrued.

Product Limited Warranty whichever is greater.

LIMITATION OF LIABILITY

INFOCUS’ LIABILITY.

repair.

TION.

The Limited Warranty periods hereof commence on the date of purchase by

the end-user customer. These Limited Warranty provisions shall apply only

resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS

cus.com/contactsupport 2) a service facility authorized by InFocus or 3) the

to the end-user purchaser (first person or entity that purchased a new Prod-

DURATIONS PROVIDED HEREIN, AND INFOCUS WILL HONOR ALL

Any person exercising a claim under this Limited Warranty must establish

to the satisfaction of InFocus both the date of purchase and that the Product

was purchased new. The sales receipt or invoice, showing the date of pur-

During the Limited Warranty period, to exercise this Limited Warranty, the

For Warranty service, the purchaser will be advised to return or deliver the

defective Product freight and all fees prepaid, to an InFocus Service Center

InFocus, a Return Material Authorization Number (RMA #) is required and

must be clearly displayed on the outside of the shipping carton or a similar

Products returned for Warranty service must be accompanied by a written

letter that(i) explains the problem; (ii) provides proof of date of purchase;

number of the Product. Upon request of InFocus Corporation or an autho-

uct for personal or business use and not for the purpose of distribution or

WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE

or to a service facility authorized by InFocus. When returning Product to

facility authorized by InFocus will return the repaired/replaced Product

AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY

purchaser must first contact 1) InFocus customer support at www.info-

package affording an equal degree of protection. InFocus or the service

(iii) provides the dealer’s name; and (iv) provides the model and serial

chase of the Product is the proof of the date of purchase.

To Be Eligible For Limited Warranty Coverage

To Obtain Warranty Service

freight prepaid to the purchaser.

SUCH CONSUMER RIGHTS.

Limited Warranty Period

place of original purchase.

NOT APPLY TO YOU.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
no start up screenplug power cord in projector’s left side remove lens cap toggle power switch toggle power switch on side p.22
image fuzzy or cropped A AAset your computer’s display resolution to the native resolution of the projector (Start>Settings>Control Panel>Display>Settings tab) select 800x600 For a laptop, disable laptop monitor or turn-on dual- display mode p.24
image not squareadjust Keystone on keypad p.25
image not sharp A Badjust Sharpness (video sources only) in the Picture>Advanced menu p.25
image upside downB Aturn off ceiling in Settings>System menu p.26
image reversed left to right Aturn off rear in Settings>System menu p.26
The video embedded in my PowerPoint presentation does not play on the screen A A B Bturn off the internal LCD display on your laptop p.27
“Change lamp” message appears at startup or lamp won’t turn on and LED blinking red LEDlamp must be replaced (see page 41) replace lamp p.28

Ask about the InFocus X2

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus X2

Be the first to ask — other owners or our team will answer.

Original document

InFocus X2 manual PDF

49 pages·2.5 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…