EN
InFocus logo
Official user manual

InFocus W1102

38 pages·7.5 MB·Projector·PDF·ENDEFRITNLJA
InFocus W1102
Table of Contents 33 sections Introduction · Positioning the projector · Projector and device connector guide · Connecting a computer source · … ShowHide
Page 1 of the InFocus W1102 user manual — Regulatory models: W1100, W1102
Page 1 · click to enlarge
Page 1

IN1100, IN1102

InFocus W1102 — IN1100, IN1102 diagram (page 1)
Fig. 1

Regulatory models: W1100, W1102

010-1712-04

Page 2 of the InFocus W1102 user manual
Page 2 · click to enlarge
Page 2
Declaration of Conformity ManufacturerInFocus Corporation 13190 SW 68th Parkway, Portland, Oregon 97223-8368 USA

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

We declare under our sole responsibility that this projector conform to the following directives and norms:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

EMC Directive 2004/108/EC EMCEN 55022

EN 55024 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 2006/95/EC Safety: IEC 60950-1: 2005, MOD

Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.

DisplayLink is a trademark of DisplayLink Corporation. Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.

Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Agency Approvals UL, cUL

Other specific Country Approvals may apply. Please see product certification label.

This document applies to regulatory models W1100 and W1102.

Input ratings100-240Vac, 2.3-0.9A, 50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.

FCC Warning · Trademarks · EN 55022 Warning

Page 3 of the InFocus W1102 user manual — 3’ / 1 m
Page 3 · click to enlarge
Page 3

Table of Contents Introduction 3 Positioning the projector 5 Projector and device connector guide 6 Connecting a computer source 9 Required computer connections (DisplayLink or VESA) 9 Optional computer connections 9 Displaying an image 10 Adjusting the image 11 Connecting a video device 12 Video device connections 13 Composite video connection 13 S-video connection 13 VESA connection 13 Component video connection 13 Shutting down the projector 14 Troubleshooting your setup 14 Using the remote control 22 Using the audio 23 Using the keypad buttons 24 Optimizing computer images 25 Presentation features 25 Optimizing video images 26 Customizing the projector 26 Using the menus 27 Basic Picture menu 28 Advanced Picture menu 29 Setup menu 30 Status and Service menu 32 Maintenance 33 Cleaning the lens 33 Using the security lock 33 Replacing the projection lamp 34

  • Place the projector in a horizontal position no greater than 15 degrees off axis.
  • Locate the projector in a well-ventilated area without any obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.
  • Locate the projector at least 4' (1.2 m) away from any heating or cooling vents.
  • Only genuine InFocus lamps are tested for use in this projector. InFocus is not liable for the performance, safety or certification of any other lamps. The use of other lamps violates the projector warranty and voids all certification marks on this projector.
  • Use only the power cord provided. A surge-protected power strip is recommended.
  • Refer to this guide for proper startup and shutdown procedures.
  • Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See <a href="http://www.lamprecycle.org" rel="nofollow noopener" target="_blank">www.lamprecycle.org</a> .
  • In the unlikely event of a lamp rupture, particles may exit through the projector side vents. When the projector is turned on, keep people, food, and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below.

3’ / 1 m

2’ / 0.6 m

Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty Booklet.

Page 4 of the InFocus W1102 user manual — Introduction
Page 4 · click to enlarge
Page 4

Introduction

Your new digital projector is simple to connect, easy to use, and straightforward to maintain. The IN1100 has native XGA 1024x768 resolution, and the IN1102 has WXGA 1280x800 resolution. This guide applies to all products. They are compatible with a wide variety of computers and video devices.

InFocus W1102 — Introduction diagram (page 4)
Fig. 2 · Introduction

Product specifications To read the latest specifications on your multimedia projector, be sure to visit our website at www.infocus.com as specifications are subject to change.

Accessories The standard accessories that came with your projector are listed in the included Quick Start Poster/Booklet. Optional accessories can be found on our website at www.infocus.com or at your retailer or dealer.

remote control receiver (IR)

Online registration Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives.

connector panel remote control receiver (IR)

InFocus W1102 — Introduction diagram (page 4)
Fig. 3 · Introduction

lens · security lock · elevator foot

Page 5 of the InFocus W1102 user manual — Introduction
Page 5 · click to enlarge
Page 5

Connector panel The projector provides the following connectors:

  • VESA computer
  • S-video
InFocus W1102 — Introduction diagram (page 5)
Fig. 4 · Introduction
  • Composite video
  • Audio in
  • USB DisplayLink connector, for computer video input. This USB connection also provides slide advance (and mouse control when used with an optional remote control only)
Show 4 more labels / short text on this page
composite · computer · video · security lock
Page 6 of the InFocus W1102 user manual — Positioning the projector
Page 6 · click to enlarge
Page 6

Positioning the projector

Table 1(IN1100) Range of distance to the screen for a given screen size

To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines:

Diagonal Screen Size (inches/m)Distance to screen Maximum Minimum distance Distance (feet/m) (feet/m) 60/1.5 80/2.0 90/2.3 150/3.88.6/2.6 7.8/2.4 11.5/3.5 10.4/3.2 12.9/3.9 11.7/3.6 21.5/6.6 19.5/5.9
InFocus W1102 — Positioning the projector diagram (page 6)
Fig. 5 · Positioning the projector
  • Position the projector on a flat surface at a right angle to the screen. The projector must be at least 4.9 feet (1.5m) from the projection screen.
  • Position the projector within 10 feet (3m) of your power source and within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within 6 inches (.15m) of a wall or other object.
  • Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image.
  • The image exits the projector at a given angle. IN1100 image offset is 115%; IN1102 image offset is 112.4%. This means that if you have an image 10’ high, the bottom of the image will be 1.5' (IN1100) and 1.24' (IN1102) above the center of the lens.
Table 2(IN1102) Range of distance to the screen for a given screen size
Diagonal Screen Size (inches/m)Distance to screen Maximum Minimum distance Distance (feet/m) (feet/m) 60/1.5 80/2.0 90/2.3 150/3.87.2/2.2 6.6/2.0 9.6/2.9 8.8/2.7 10.8/3.3 9.9/3.0 18.0/5.5 16.4/5.0
InFocus W1102 — Positioning the projector diagram (page 6)
Fig. 6 · Positioning the projector

(IN1100) (IN1102) 10 ft high image

10 ft high image

InFocus W1102 — Positioning the projector diagram (page 6)
Fig. 7 · Positioning the projector
InFocus W1102 — Positioning the projector diagram (page 6)
Fig. 8 · Positioning the projector

bottom of image 1.24 ft above center of lens

bottom of image 1.5 ft above center of lens

Page 7 of the InFocus W1102 user manual — Projector and device connector guide
Page 7 · click to enlarge
Page 7

Projector and device connector guide

The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as computers, standard VCRs, DVD players (progressive and interlaced), HDTV sources (1080i, 1080p and 720p HDTV formats), TV and satellite tuners, camcorders, video games (progressive and interlaced), and laser disc players.

InFocus W1102 — Projector and device connector guide diagram (page 7)
Fig. 9 · Projector and device connector guide
Show 4 more labels / short text on this page
composite · computer · video · security lock
Page 8 of the InFocus W1102 user manual — Projector and device connector guide
Page 8 · click to enlarge
Page 8
Video DeviceVideo CompatibilityIf Your Device Connector IsAttach to Adapter or Labeled Connector on ProjectorFor Setup Instructions, seeComments Standard Broadcast TV (not HDTV) via: cable, digital cable, satellite TV, DVD, or VCRNTSC, PAL, and SECAM formatsComposite video or S-videoVideo 2 or Video 1Composite video connection on page 13. S-video connection on page 13Not for progressive (i.e. HDTV) sources. See page 8. Standard Video CameraNTSC, PAL, and SECAM formatsComposite video or S-videoVideo 2 or Video 1Composite video connection on page 13. S-video connection on page 13Not for progressive (i.e. HDTV) sources. See page 8. Standard Video GameNTSC, PAL, and SECAM formatsComposite video or S-videoVideo 2 or Video 1Composite video connection on page 13. S-video connection on page 13Not for progressive (i.e. HDTV) sources. See page 8.
Page 9 of the InFocus W1102 user manual — Projector and device connector guide
Page 9 · click to enlarge
Page 9
Video DeviceVideo CompatibilityIf Your Device Connector IsAttach to Adapter or Labeled Connector on ProjectorFor Setup Instructions, seeComments HDTV (High Definition TV)1080i, 1080p, 720p Component 480iVGA Component videoComputer 2 Computer 2 via optional VESA to Component adapterVESA connection on page 13 Component video connection on page 13 Progressive DVD1080i, 1080p, 720p Component 480p and 480iVGA Component videoComputer 2 Computer 2 via optional VESA to Component adapterVESA connection on page 13 Component video connection on page 13 Progressive Video Game1080i, 1080p, 720p Component 480p and 480iVGA Component videoComputer 2 Computer 2 via optional VESA to Component adapterVESA connection on page 13 Component video connection on page 13
Page 10 of the InFocus W1102 user manual — Optional computer connections
Page 10 · click to enlarge
Page 10

Connecting a computer source

InFocus W1102 — Connecting a computer source diagram (page 10)
Fig. 10 · Connecting a computer source

Required computer connections (DisplayLink or VESA)

If your computer has Windows XP SP2 or newer*, connect the USB cable between your computer's USB port and the projector's DisplayLink connector, then follow the instructions on the screen. See the DisplayLink Manager User's Guide for more information (www.infocus.com/support/ displaylink).

* For the latest information about support for other operating systems (including Apple), go to www.infocus.com/support/displaylink

Or, connect one end of the provided computer cable to the Computer 2 connector on the projector and the other to the VESA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer’s video port first.

Connect the black power cord to the Power connector on the side of the projector and to your electrical outlet. The Power light on the Status Indicator Panel (page 14) turns amber.

Optional computer connections

To get sound from the projector, connect an audio cable (optional cable, not included) to your computer and to the Audio In connector on the projector. You may also need an adapter.

To advance slides in a PowerPoint presentation using the remote control, plug the USB cable into the USB mouse connector on your computer and the DisplayLink connector on the projector.

Page 11 of the InFocus W1102 user manual — Displaying an image
Page 11 · click to enlarge
Page 11

Displaying an image

Touch the Power button.

The Power button blinks green and the fans start to run. When the lamp comes on, the start up screen displays and the Power button is steady green. It can take a minute for the image to achieve full brightness.

? No start up screen? Get help on page 15.

turn on computer or video device

Turn on your computer or video device.

The image should appear on the projection screen. If it doesn’t, press the Source button on the projector’s keypad or remote.

If you are using a VESA cable to connect your computer to the projector (instead of DisplayLink):

If using a laptop, make sure its external video port is active.

Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like FN + F8 or CRT/ LCD key turns the external display on and off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol. Press FN and the labeled function key simultaneously. Refer to your laptop’s documentation to learn your laptop’s key combination.

activate laptop’s external port

monitor key or LCD/CRT key

InFocus W1102 — Displaying an image diagram (page 11)
Fig. 11 · Displaying an image

? No laptop image? Try pressing the Auto Image button on the keypad. Get help on page 15.

? Is your laptop connected to the projector's DisplayLink connector? See the InFocus DisplayLink Manager User's Guide (www.infocus.com/ support/displaylink) for troubleshooting information.

press Power button · FN key

Page 12 of the InFocus W1102 user manual — Adjusting the image
Page 12 · click to enlarge
Page 12

Adjusting the image

If necessary, adjust the height of the projector by pressing the elevator foot release button to extend the foot.

If necessary, rotate the leveling foot located at the rear of the projector.

Avoid placing your hands near the hot exhaust vent at the side of the projector.

Position the projector the desired distance from the screen at a 90 degree angle to the screen.

InFocus W1102 — Adjusting the image diagram (page 12)
Fig. 12 · Adjusting the image

See page 5 for a table listing screen sizes and distances.

Adjust the zoom or focus, as needed.

adjust zoom or focus

If the image is not square, first make sure that the projector is perpendicular to the screen. If the image is larger or smaller on the top or bottom edge of the screen, press the top Keystone button to reduce the upper part of the image, and press the bottom Keystone button to reduce the lower part.

InFocus W1102 — Adjusting the image diagram (page 12)
Fig. 13 · Adjusting the image

If the left or right side of the screen is larger or smaller the other, you can turn the projector to the left or to the right a few degrees to square the image.

Adjust the Contrast or Brightness in the Basic Picture menu. See page 28 for help with these menu adjustments.

adjust Basic Picture menu

For Aspect Ratio, keep in mind that DVD players must be configured for 16:9 in order to view the highest quality image. For more information regarding Aspect Ratio, see page 12.

Show 5 more labels / short text on this page
release button · adjust height · elevator foot · adjust distance · adjust keystone
Page 13 of the InFocus W1102 user manual — Connecting a video device
Page 13 · click to enlarge
Page 13

Connecting a video device

4:3 screen 16:9 screen

You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. You can connect the audio directly to the projector to get sound from the built-in speaker, or you can bypass the projector’s audio system and connect the audio directly from your source to a stereo system.

Do Not Use 4:3 mode

You can connect the projector to most video devices that can output video. You cannot directly connect the coaxial cable that enters the building from a cable or satellite company, the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner.

Before connecting your projector, you should decide which aspect ratio you want to use. The projector’s Aspect Ratio setting is accessed through the Resize button on the remote or through the projector’s Basic Picture Menu. See page 28 for more information.

16:9 mode

What is Aspect Ratio? Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9. If you’re projecting onto a screen, the size/shape of the screen may determine which aspect ratio to use. If you are projecting onto a blank wall, you don’t have the screen size restriction. What you plan to project will also help you choose between 4:3 and 16:9. Most TV shows are 4:3, while most movies are 16:9.

If you have a 16:9 screen then you should select an aspect ratio of 16:9 for anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3 screen you should still use 16:9 for anamorphic movies or HDTV, but you also have the option of using either 4:3 (to fill the screen) or Native (for direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies only appear correctly if the DVD player is set to output to a 16:9 television.

Native mode (NTSC only)

Page 14 of the InFocus W1102 user manual — VESA connection
Page 14 · click to enlarge
Page 14

Video device connections

Component video connection

No video cables are provided with the projector. You can order cables from InFocus or provide your own.

If your HD video device has component connectors, an optional Component to VESA adapter can be used. Plug the component cable into the video device. Plug the other end of the component cable into the adapter and plug the adapter into the Computer 2 connector. Component offers the highest quality video output.

Composite video connection

Plug the composite video cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yellow Video 2 connector on the projector.

Plug the white connector of a Mini-plug audio Y-cable into the left audio out connector on the video device and plug the red connector into the right audio out connector on the video device. Plug the other end of the cable into the Audio In connector on the projector.

Keep in mind that video output from composite connections is not as high quality as S-video.

S-video connection

If your video device uses a round, four-prong S-video connector, plug an S- video cable into the S-video connector on your video device and into the Video 1 connector on the projector. Use the audio cable as described above.

Keep in mind that S-video delivers higher quality video output than composite.

VESA connection

If your video device has a 15-pin VGA output, plug one end of the included computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the computer cable into the Computer 2 connector on the projector.

Page 15 of the InFocus W1102 user manual — Troubleshooting your setup
Page 15 · click to enlarge
Page 15

Shutting down the projector

The Status Indicator Panel on top of the projector indicates the state of the projector and can help you troubleshoot.

The projector automatically displays a black screen after no active source is detected for 30 minutes. This black screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or keypad button is pressed.

Table 3Status indicator light behavior and meaning

Screen Save Time You can make the black screen appear after a preset number of minutes by turning on the Screen Save Time feature in the Setup menu. See page 30.

Status Indicator Panel icons Meaning

The projector is plugged in.

Auto Off Time The projector also has an Auto Off Time feature that automatically turns the projector off after no active sources are detected and no user interaction with the projector is performed for 30 minutes. By default, this feature is off. You can change the length of time, see page 30.

The power button has been pressed and the software is initializing.

The projector is on and initialized.

Turning off the projector To turn the projector off, press the Power button on the remote or keypad. The lamp turns off and the LED blinks amber for 1 minute while the fans continue to run to cool the lamp. When the lamp has cooled, the LED lights amber and the fans stop. Unplug the power cable to completely power off the projector.

The power button has been pressed to turn the projector off and the fans are running to cool the projector.

Thermometer The projector is too hot. Make sure the vents aren’t blocked (see page 20). Turn off the projector and wait one minute, then turn the projector on again. Visit www.infocus.com/support to contact service.

Troubleshooting your setup

If your image appears correctly on the screen, skip to the next section. If it does not, troubleshoot the setup.

Lamp Turn off the projector and wait one minute, then turn the projector on again. If the lamp light turns on again, replace the lamp and reset the lamp timer.

Wrench/Service Turn off the projector and wait one minute, then turn the projector on again. If the service lamp turns on again, service is required. Visit www.infocus.com/support to contact Service.

Show 4 more labels / short text on this page
Power, solid amber · Power, blinking green · Power, solid green · Power, blinking amber
Page 16 of the InFocus W1102 user manual — Shutting down the projector
Page 16 · click to enlarge
Page 16
InFocus W1102 — Shutting down the projector diagram (page 16)
Fig. 14 · Shutting down the projector

No start up screen Plug power cord into the projector press power button

Only start up screen appears If your computer is using the projector's DisplayLink connector, see the DisplayLink User's Guide for troubleshooting information.

Page 17 of the InFocus W1102 user manual — A
Page 17 · click to enlarge
Page 17

No computer image, just the words “Signal out of range”

Press the Auto Image button on keypad adjust computer refresh rate in Control Panel > Display > Settings > Advanced > Adapter (location varies by operating system)

A

Signal out of the range

InFocus W1102 — A diagram (page 17)
Fig. 15

A

A

You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped”

Only my laptop’s background appears, not the Desktop icons

If your computer is using the DisplayLink connector, use DisplayLink Manager software to change the display mode from Extended Desktop to Duplicated Desktop. See the DisplayLink Manager User's Guide for more information.

Background and Desktop projected

A

Disable “Extend my Windows Desktop” in Control Panel > Display > Settings > Display 2 (location varies by operating system)

A

InFocus W1102 — A diagram (page 17)
Fig. 16

A

A

Uncheck this option, then click Apply

Problem Solution Result · Computer image projected

Page 18 of the InFocus W1102 user manual — Shutting down the projector
Page 18 · click to enlarge
Page 18
InFocus W1102 — Shutting down the projector diagram (page 18)
Fig. 17 · Shutting down the projector

Image fuzzy or cropped Set your computer’s display resolution to the native resolution of the projector (Start > Settings > Control Panel > Display > Settings tab)

For a laptop, disable laptop monitor or turn- on dual-display mode

Image not centered on screen Move projector, adjust zoom, adjust height Correct image

Adjust horizontal or vertical position in Advanced Picture menu

Page 19 of the InFocus W1102 user manual — A B
Page 19 · click to enlarge
Page 19

Image not square Adjust Keystone on keypad Square image

Image not sharp Adjust Sharpness in the Basic Picture menu Correct image

InFocus W1102 — Shutting down the projector diagram (page 19)
Fig. 18 · Shutting down the projector

A B

A B

Image does not fit 4:3 or 16:9 screen Change aspect ratio to 4:3 or 16:9 in Basic Picture > Aspect ratio menu

InFocus W1102 — A B diagram (page 19)
Fig. 19

Problem Solution Result · Correct image

Page 20 of the InFocus W1102 user manual — B
Page 20 · click to enlarge
Page 20

Image reversed left to right Turn off Rear Project in Setup menu Correct image

InFocus W1102 — Shutting down the projector diagram (page 20)
Fig. 20 · Shutting down the projector

A

A B

Projected colors don’t match source Adjust color, tint, brightness, contrast in the Basic Picture menu Correct image

InFocus W1102 — A diagram (page 20)
Fig. 21

COLOR

COLOR

The video embedded in my PowerPoint presentation does not play on the screen

If your computer is using the projector's DisplayLink connector, see the DisplayLink User's Guide for video troubleshooting information.

Embedded video plays correctly

A

A

Turn off the internal LCD display on your laptop

B

A

A

B

B

Problem Solution Result

Page 21 of the InFocus W1102 user manual — Shutting down the projector
Page 21 · click to enlarge
Page 21
InFocus W1102 — Shutting down the projector diagram (page 21)
Fig. 22 · Shutting down the projector

Lamp won’t turn on, Temperature light is on Make sure vents aren’t blocked, turn off the projector and allow it to cool for one minute

“Replace lamp” message appears at startup, lamp won’t turn on, Lamp light is turned on

Lamp must be replaced (see page 34) Lamp turns on

Page 22 of the InFocus W1102 user manual — Shutting down the projector
Page 22 · click to enlarge
Page 22

If you need assistance, visit our website at www.infocus.com/service or call us. Check out our HOW TO section there for additional information. See the Quick Start Poster/Booklet for support contact information.

This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full value.

Still need assistance?

Page 23 of the InFocus W1102 user manual — Using the remote control
Page 23 · click to enlarge
Page 23

Using the remote control

InFocus W1102 — Using the remote control diagram (page 23)
Fig. 23 · Using the remote control

The remote uses two (2) AA batteries. They are easily installed by removing the cover from the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.

To operate, point the remote at the front of the projector (not at the computer). The range of optimum operation is about 15 feet (4.5m).

Press the remote’s Power button to turn the projector on and off (see page 14 for shutdown info).

Press the remote’s Menu button to open the projector’s menu system. Use the arrow buttons to navigate, and the Select button to select features and adjust values in the menus. See page 27 for more info on the menus.

The remote also has a Source button to switch between sources.

The remote also has:

  • Volume buttons to adjust the sound.
  • Custom button that can be assigned to a special function, like Blank Screen or Freeze (see page 30).
  • Source button to switch between sources.
  • Blank button to blank the screen.
  • Presets button to select stored settings (see page 28).
  • Mute button to silence the audio.
  • Auto Image button to resynch the projector to the source
  • Resize button to switch among aspect ratios (see page 28). Troubleshooting the remote
  • Make sure the batteries are installed in the proper orientation and are not dead.
  • Make sure you’re pointing the remote at the projector or the screen, not the computer, and are within the remote range of 15 feet (4.5m). For best results, point the remote at the projector.

navigation buttons

Page 24 of the InFocus W1102 user manual — Using the audio
Page 24 · click to enlarge
Page 24

Using the audio

InFocus W1102 — Using the audio diagram (page 24)
Fig. 24 · Using the audio

Using the projector’s speaker To use the projector's speaker, connect the audio source to the projector's Audio In connector.

To adjust the volume, press the Volume buttons on the keypad or remote.

Troubleshooting Audio If you aren’t hearing the audio, check the following:

  • Make sure the volume is turned up enough. Press the Volume button on the keypad or remote.
InFocus W1102 — Using the audio diagram (page 24)
Fig. 25 · Using the audio
  • Make sure the correct source is active.
  • Make sure that you are connected to an “audio out” connector on the source as opposed to a “line-in” or “microphone” connector.
  • Adjust the audio source.
  • If playing a video, make sure the playback has not been paused.

connect audio cable · adjust volume

Page 25 of the InFocus W1102 user manual — Using the keypad buttons
Page 25 · click to enlarge
Page 25

Using the keypad buttons

Most buttons are described in detail in other sections, but here is an overview of their functions:

Power–turns the projector on and off (page 10).

Auto Image–resets the projector to the source.

Presets–cycles through the available preset settings (page 28).

Keystone–adjusts squareness of the image (page 11).

Menu–opens the on-screen menus (page 27).

Select–confirms choices made in the menus (page 27).

Up/Down arrows–navigates to and adjusts settings in the menus (page 27).

Volume–adjusts sound (page 23).

Source–changes the active source (page 10).

menu navigation buttons

Page 26 of the InFocus W1102 user manual — Optimizing computer images
Page 26 · click to enlarge
Page 26

Optimizing computer images

Presentation features

Several features are provided to make giving presentations easier. Here is an overview, details are found in the menu section.

After your computer is connected properly and the computer’s image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 27.

  • The Custom key allows you to assign various features to the button. The default effect is Source Info, which displays information about the projector and current source. See page 30 for details.
  • Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu (page 28).
  • Change the Aspect Ratio. Choose the option that best fits your input source (page 28).
  • The Search Screen option lets you change the appearance of the blank screen and start up screen (page 31).
  • Adjust the Color Temperature in the Advanced Picture menu (page 28).
  • Two options, Auto Off and Screen Save Time, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life (page 30).
  • Adjust the Phase, Tracking, or Horizontal or Vertical position in the Advanced Picture menu (page 29).
  • Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these settings later (page 28).
  • If your computer is using the projector's DisplayLink connector, see the InFocus DisplayLink Manager User's Guide for information about optimizing images.
Page 27 of the InFocus W1102 user manual — Dynamic Messaging
Page 27 · click to enlarge
Page 27

Optimizing video images

Customizing the projector

After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 27.

You can customize the projector for your specific setup and needs. See page 30 to page 31 for details on these features.

  • For rear projection, turn Rear Project on in the Setup menu.
  • Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Basic Picture menu (page 28).
  • Specify which source the projector checks first for active video during power-up.
  • Change the Aspect Ratio. Choose the option that best fits your input source (page 28).
  • Specify the function of the Custom key on the remote.
  • Turn the projector’s display messages on and off.
  • Select a Sharpness setting (page 28).
  • Turn on power saving features.
  • Adjust the Color Temperature. Select a listed warmth value (page 29).
  • Specify appearance of blank screen and startup screen.
  • Turn on Overscan to remove noise on the edges of the image (page 29).
  • Specify the language viewed on the menus.
  • Save settings for the active source as a preset.

Dynamic Messaging

You can use Command Line Interface (CLI) commands to display text messages on the projector (for example, to display urgent alert messages to employees). This requires a connection to the projector’s RS-232 serial control connector. Go to our support website to download the RS-232 command reference for your projector.

Page 28 of the InFocus W1102 user manual — Using the menus
Page 28 · click to enlarge
Page 28

Using the menus

To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) Use the arrow buttons to move up and down to highlight the desired menu, then press the Select button.

To change a menu setting, highlight it, press Select, then use the up and down arrow buttons to adjust the value or select an option or turn the feature on or off. Press Select to confirm your changes. Use the arrows to navigate to another setting. When your adjustments are complete, press Menu to access a different menu; press the Menu button at any time to navigate to the higher-level menu and ultimately close the menus.

InFocus W1102 — Using the menus diagram (page 28)
Fig. 26 · Using the menus
InFocus W1102 — Using the menus diagram (page 28)
Fig. 27 · Using the menus

The menus are grouped by usage:

  • The Basic Picture menu provides common image adjustments.
  • The Advanced Picture menu provides more complex image adjustments.
  • The Setup menu provides set-up type adjustments that are not changed often.
  • The Status and Service menu provides information about the projector and source.

Basic Picture menu Advanced Picture menu

InFocus W1102 — Using the menus diagram (page 28)
Fig. 28 · Using the menus
InFocus W1102 — Using the menus diagram (page 28)
Fig. 29 · Using the menus

Setup menu Status and Service menu

keypad navigation buttons

Page 29 of the InFocus W1102 user manual — Basic Picture menu
Page 29 · click to enlarge
Page 29

Basic Picture menu

To adjust the following settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press Select to confirm the changes.

Brightness: changes the intensity of the image.

Contrast: controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image.

Sharpness: (video sources only) changes the clarity of the edges of a video image. Select a sharpness setting.

Color: adjusts a video image from black and white to fully saturated color. The color setting applies to video sources only.

Tint: adjusts the red-green color balance in the image of NTSC video images. The tint setting applies to NTSC video sources only.

Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9.

Select Auto to have the projector choose the ratio. Choose Native to see the unmodified input with no resizing by the projector. Select 16:9 to watch enhanced widescreen DVDs.

For more information regarding Aspect Ratio, see page 12.

Apply Preset...: Presets are provided that optimize the projector for displaying computer presentations and video images under certain conditions.

There is also a user-definable preset. To set this preset, adjust the image and select Save User in the Presets menu. You can recall these settings in the future by selecting the User preset.

Digital Zoom: changes the size of projector’s display area. If the display area has been resized by this setting, it can be moved by changing the Horz Shift and Vert Shift settings.

Horz Shift/Vert Shift: moves the display area horizontally or vertically if its size has been changed by the Digital Zoom setting.

Keystone: adjusts the image vertically and makes a squarer image. You can also adjust keystone from the keypad.

increasing keystone decreasing keystone

Basic Picture menu · Aspect ratio

Page 30 of the InFocus W1102 user manual — Advanced Picture menu
Page 30 · click to enlarge
Page 30

Advanced Picture menu

BrilliantColor™: produces an expanded on-screen color spectrum that delivers enhanced color saturation for bright, true-to-life images. Choose Normal Look for most video sources and Bright Look for most computer sources.

White Peaking: (video sources only) increases the brightness of whites that are near 100%.

Color Temperature: changes the intensity of the colors. Select a listed relative warmth value.

Force wide: This feature is to help with image-locking problems when the correct mode cannot be determined. If this feature is off and the exact resolution mode cannot be determined, the analog locking algorithms will use a 4:3 mode for the image. If this feature is on and the exact mode cannot be determined, the analog locking algorithms choose the best-matched wide mode (either 16:9 or 16:10) for the image.

Overscan: removes noise around the video image.

Phase: adjusts the horizontal phase of a computer source.

Sync Threshold: (progressive signals only) If a hardware device, such as a DVD player, is not syncing properly with the projector, select this option to help it to sync when connected to the projector.

Tracking: adjusts the vertical scan of a computer source.

Color Space: This option applies to computer and component video sources. It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources or choose either REC709 or REC601 for component video sources.

Gamma: select the appropriate gamma from among Video, Film, Bright, and CRT.

Horizontal/Vertical Position: adjusts the position of a computer source.

Advanced Picture menu

Page 31 of the InFocus W1102 user manual — Setup menu
Page 31 · click to enlarge
Page 31

Setup menu

Power Sounds: controls whether the projector makes a sound when powered on and off.

Language: allows you to select a language for the onscreen display.

Auto Source: when this feature is On, the projector automatically finds the active source, checking the selected Power-up Source first. When this feature is Off, the projector defaults to the source selected in Power-up Source. To display another source, you must manually select one by pressing the Source button on the remote or keypad.

Custom Key: allows you to assign a different function to the Custom button, allowing you to quickly and easily use the effect. Highlight an effect and press Select to choose a different one.

  • Source Info : the default action. Shows the Source Info menu.
  • Projector Info : Shows the Projector Info menu.
  • Aspect Ratio : toggles among 4:3, 16:9, and Native (see page 12 and page 28).
InFocus W1102 — Setup menu diagram (page 31)
Fig. 30 · Setup menu
  • Auto Image : resets the projector to the source (page 24).
  • Overscan : removes noise around the image.
  • Blank Screen : displays an empty screen.
  • Freeze Screen : pauses the projected image.
  • Mute : turns off all sound.
  • Source : cycles through available sources.

Blank Key: Select what to display when the blank key on the remote is depressed: your custom snapshot, a solid color screen (blue, black or white), the factory logo screen, a timer, or test patterns. The timer option is useful for classroom tests or break times during meetings.

Power-up Source: determines which source the projector checks first for active video during power-up.

Video Standard: when this feature is set to Auto, the projector attempts to automatically pick the video standard based on the input signal it receives. (The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors may not look right or the image may appear “torn.” If this happens, manually select a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.

AC Power On: when this feature is on, the projector automatically turns on when electrical power is connected.

Auto Off Time: automatically turns the projector off after no signals are detected for a preset number of minutes. If an active signal is received before the projector powers down, the image will be displayed.

Screen Save Time: automatically blanks the screen with a black color after no signals are detected for a preset number of minutes. The image returns when an active source is detected or a remote or keypad button is pressed.

Closed Captions: controls closed caption display while audio is not muted. If this setting is not off, and audio is not muted, and the source is NTSC and contains captions on the selected channel, then the projector must display caption text overlaid on the image.

Lamp Low Power: toggles between on and off. Turn it on to lower the light output of the lamp. This also lowers the fan speed, making the projector quieter.

Setup menu

Page 32 of the InFocus W1102 user manual — Setup menu
Page 32 · click to enlarge
Page 32

Rear Project: reverses the image so you can project from behind a translucent screen.

keypad to enter the correct button press sequence. See the description above for instructions.

Auto Keystone: automatically adjusts vertical image.

To change the PIN:

Prevent PC Screen Saver: prevents your computer from going into Screen Save mode. The projector must be connected to the PC via a USB cable for this feature to work.

Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the new PIN. You can navigate between OK and Cancel by pressing the up and down buttons on the keypad. Select OK or Cancel by pressing the Select button. Verify the new PIN.

Search Screen: allows you to display a blank screen instead of the default screen at startup, and when no source is detected.

If you lose or forget your custom PIN:

Show Messages: displays status messages (such as “Searching”) in the lower- left corner of the screen.

Contact InFocus support. Go to www.infocus.com/support

Menu Offset: allows you to change the position of the On Screen Display items.

Menu Transparency: allows you to change how much of the projected image behind the menu you can see. As the value increases, more of the image behind the menu is visible.

Magnify Controls: determines whether the select key can be used to change magnify settings when the OSD menu is not visible.

PIN Protect: the PIN (personal identification number) feature allows you to password protect your projector. Once you enable the PIN feature, you must enter the PIN before you can project an image. The default PIN on this projector is Menu-Up-Down-Select-Source. Use the navigation buttons on the remote or keypad to enter the correct 5-button press sequence. When all 5 numbers are entered correctly, press the Select button on the remote or keypad to select OK. If the message “Wrong PIN” appears, verify the code and re-enter it. If you mis-enter a number, you must enter 5 numbers and press the Select button in order to access the “Wrong PIN” message and re- enter the code.

To enter the PIN at projector startup: Power up the projector. The “Enter PIN” dialog box appears after the startup screen. Enter the PIN. Use the navigation buttons on the remote or

Page 33 of the InFocus W1102 user manual — Status and Service menu
Page 33 · click to enlarge
Page 33

Status and Service menu

Source Info: a read-only display of current source settings.

Projector Info: a read-only display of current projector settings.

Reset Lamp Hours: resets the lamp hours used counter in the Projector Info menu to zero. Do this only after changing the lamp.

Factory Reset: restores all settings to their default.

Service Code: only used by authorized service personnel.

Status and Service menu

Page 34 of the InFocus W1102 user manual — Using the security lock
Page 34 · click to enlarge
Page 34

Maintenance

InFocus W1102 — Maintenance diagram (page 34)
Fig. 31 · Maintenance

Cleaning the lens

1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

  • Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

2 Lightly wipe the cleaning cloth over the lens in a circular motion.

Using the security lock

InFocus W1102 — Using the security lock diagram (page 34)
Fig. 32 · Using the security lock

The projector has a security lock for use with a PC Guardian Cable Lock System. Refer to the information that came with the lock for instructions on how to use it.

security lock

Page 35 of the InFocus W1102 user manual — WARNINGS :
Page 35 · click to enlarge
Page 35

Replacing the projection lamp

InFocus W1102 — Replacing the projection lamp diagram (page 35)
Fig. 33 · Replacing the projection lamp

The lamp hours used timer in the Projector Info menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, the message “Change lamp” appears on the screen at startup.

  • NOTE : You can order new lamps from <a href="http://www.infocus.com" rel="nofollow noopener" target="_blank">www.infocus.com</a> (in select areas), your retailer or your dealer. Only genuine InFocus lamps are tested for use in this projector. InFocus is not liable for the performance, safety or certification of any other lamps. The use of other lamps violates the projector warranty and voids all certification marks on this projector. 1 Turn off the projector and unplug the power cord.

2 Wait 60 minutes to allow the projector to cool thoroughly.

3 Turn the projector upside down on a soft cloth so that the lamp door is facing you.

turn off and unplug projector

WARNINGS :

  • To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.
  • Only genuine InFocus lamps are tested with this projector. Use of other lamps may cause electrical shock and fire.
  • Unplug the power cord before replacing the lamp.
  • Do not drop the lamp module. The glass may shatter and cause injury.
  • Do not touch the glass lamp screen. Fingerprints can obscure projection sharpness.

Lamp hours

Page 36 of the InFocus W1102 user manual — Replacing the projection lamp
Page 36 · click to enlarge
Page 36
  • Be extremely careful when removing the lamp housing. In the unlikely event that the lamp ruptures, small glass fragments may be generated. The lamp module is designed to contain most of these fragments, but use caution when removing it. Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement. Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See <a href="http://www.lamprecycle.org" rel="nofollow noopener" target="_blank">www.lamprecycle.org</a> .

4 Loosen the two captive screws on the lamp door and lift the door off.

5 Loosen the two captive screws that attach the lamp housing to the projector.

InFocus W1102 — Replacing the projection lamp diagram (page 36)
Fig. 34 · Replacing the projection lamp

6 Carefully remove the lamp housing. Dispose of the lamp in an environmentally proper manner.

7 Install the new lamp housing and tighten the screws.

InFocus W1102 — Replacing the projection lamp diagram (page 36)
Fig. 35 · Replacing the projection lamp

8 Replace the lamp door.

9 Plug in the power cord and press the Power button to turn the projector back on.

10 To reset the lamp hour timer, navigate to the Status and Service menu and select Reset Lamp Hours. See page 32 for details.

loosen screw · loosen screw

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No start up screen APlug power cord into the projector press power button p.16
Only start up screen appears SS cta ertu np re AIf your computer is using the projector's DisplayLink connector, see the DisplayLink User's Guide for troubleshooting information. Press the Source button activate laptop’s external port Restart laptop p.16
No computer image, just the words “Signal out of range” ngS ig na l o u et o f the ra APress the Auto Image button on keypad adjust computer refresh rate in Control Panel > Display > Settings > Advanced > Adapter (location varies by operating system) You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped” p.17
Only my laptop’s background appears, not the Desktop iconsIf your computer is using the DisplayLink connector, use DisplayLink Manager software to change the display mode from Extended Desktop to Duplicated Desktop. See the DisplayLink Manager User's Guide for more information. Disable “Extend my Windows Desktop” in Control Panel > Display > Settings > Display 2 (location varies by operating system) Uncheck this option, then click Apply p.17
A A p.17
Image fuzzy or cropped A ASet your computer’s display resolution to the native resolution of the projector (Start > Settings > Control Panel > Display > Settings tab) For a laptop, disable laptop monitor or turn- on dual-display mode p.18
Image not centered on screenMove projector, adjust zoom, adjust height A Adjust horizontal or vertical position in Advanced Picture menu p.18
Image not centered on screen p.18
Image not squareAdjust Keystone on keypad p.19
Image not sharp A BAdjust Sharpness in the Basic Picture menu p.19
Image does not fit 4:3 or 16:9 screenChange aspect ratio to 4:3 or 16:9 in Basic Picture > Aspect ratio menu p.19
Image reversed left to right ATurn off Rear Project in Setup menu p.20
Projected colors don’t match source COLORAdjust color, tint, brightness, contrast in the Basic Picture menu p.20
The video embedded in my PowerPoint presentation does not play on the screen A A BIf your computer is using the projector's DisplayLink connector, see the DisplayLink User's Guide for video troubleshooting information. Turn off the internal LCD display on your laptop p.20
Lamp won’t turn on, Temperature light is on Temperature light AMake sure vents aren’t blocked, turn off the projector and allow it to cool for one minute p.21
“Replace lamp” message appears at startup, lamp won’t turn on, Lamp light is turned on Lamp light ALamp must be replaced (see page 34) loosen screws loosen screws p.21

Ask about the InFocus W1102

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus W1102

Be the first to ask — other owners or our team will answer.

Original document

InFocus W1102 manual PDF

38 pages·7.5 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…