




Projection Distance (Aspect ratio 4:3)
When using this optional lens, adjust the projected image
to the left end or right end may cause the shading at a
corner area (*1) as shown in the illustration below. This
lens cannot display the projected image properly in these
areas, so adjust the left-right lens shift dial not to have the
(*1) The corner area of the projected image may appear

Shifted to the left end Shifted to the right end
40(1.0) 24(0.6) 60(1.5) 37(0.9) 70(1.8) 43(1.1) 100(2.5) 63(1.6) 120(3.0) 76(1.9) 150(3.8) 95(2.4) 200(5.1) 128(3.3) 250(6.4) 161(4.1) 300(7.6) 193(4.9) 350(8.9) 226(5.7)
Lens Shift Position(4 directional):1:1(Fixed)
Projection Distance (Aspect ratio 4:3)
y=0.0165x-0.0553
position using the following procedure.
shading in the projected image.
x:Diagonal Screen size[inch] ,
Fixed Zoom, Manual Focus
y:Projection Distance[inch]
dark, or be shaded.
Do not touch the lens to prevent fog or dirt of the lens
Use commercially available lens tissue to clean the lens
Excepting for lens, use a soft cloth to clean. When
excessively soiled dilute a neutral detergent in water, wet
Do not use detergents or chemicals other than those
Project an image as described in the LCD Projector
user's manual, and adjust the size and focus of the
See the Projection Distance table in this user's manual
In order to optimize keystone distortion correction
(trapezoidal distortion correction), make note of the
[Lens Type] shown on the label of the optional lens to
be used and select this lens type on the LCD Projector's
For more information see the "Lens Type"of the
"Service" item of the "Settings Menu" in the LCD
The distance of projection may not allow focusing on
the peripheral area of the screen. Adjust the focus to
keep the center and the peripheral area of the screen
This specifi cations are subject to change without notice.
The zoom lens may cause some distortion of the image
Distortion may appear on screen if the keystone correction
Keystone correction (trapezoidal distortion correction)
When carrying it, protect the lens parts with lens cap.
for information on optional lens projection distances.
Please read this manual and manuals for the
LCD projector to be used thoroughly to ensure
correct usage through understanding. Incorrect
Any shock or impact could result in an injury or
damage. The lens part is projected. Take care not to
Do not scratch and polish the lens with hard object.
(trapezoidal distortion correction) is overly adjusted.
on the screen depending on the zoom position.
usage could result in fi re, an injury or damage.
Exchange Manual to install this product.
(used to clean cameras, eyeglasses, etc.).
that cause deterioration of display quality.
Do not give any shock or impact.
may be limited with some lenses.
and wring out the soft cloth.
Projector user's manual.
Take care of the lens.
projected image.
option menu.
balanced.
strike it.
NOTE



※ Attach the lens cap by passing the strap through the loop on the lens cap
and the included rivet. If unnecessary, remove the currently attached lens
(2) Raise the top of the louver towards the top of the projector
and attach the 4 hooks on the top of the louver to the slots
※ Use the lens cap attached to the LCD projector for model Standard Lens.
louver to the bottom-right slot closest to the lens on the projector.
※ If the projector is installed in a high
projector. When attaching, attach the bottom-right hook on the

cap for Standard Lens.

(2) Turn the lens to the right until it "clicks" into place to ensure
4.Reattach the front cover to complete lens replacement. (1) Reattach the front cover.

3.Attach the replacement projection lens. (1) Line up the notched tab on the lens mount with the hole
(2) Re-fasten the 2 screws marked U (triangle) that were
on the upper-left part of the holder, and insert the lens.

shown in the illustration.
shown in the illustration.
behind the lens.
unplug the LCD projector, and allow at least 45 minutes
Before replacing the lens, be sure to turn off and unplug the LCD
projector, and allow at least 45 minutes for the projector to fully cool.
Removing while the cooling plate is still hot may result in burns.
Continued use with dust inside may result in fi re or electric shock.
This can cause damage to the equipment. It can also cause a
misalignment of the optical adjustment and, therefore, require
on the connectors or wires or get them caught in the circuit board
1.Remove the front cover. (1) Remove the 2 screws marked U (triangle) from the inside of
(2) Remove the 2 screws marked U (triangle) from the front of
(3) Turn the lens shift dial, and raise the projection lens to the
This can cause damage to the equipment. Be careful not to pull
This can dirty the lens and cause deterioration in image quality.

(Only for models LENS-037 and LENS-038) may stick
Transporting the LCD projector in the original projector
Lens Replacement Manual ■ Before replacing the lens, be sure to turn off and
ing plates of the LCD projector or subject them to shocks.
shipping box can cause damage to the equipment.
connectors or wires inside the LCD projector.
lens without subjecting it to shocks or vibrations.
and wait approximately ten minutes.
for the projector to fully cool.
out from the LCD projector.
Replacing the Lens
down on a soft cloth.
readjustments.
highest position.
the projector.
or case.
This manual describes the procedure for replacing the following lenses.
lens LENS-037 Fixed short focal length projection lens, louver, lens cap, strap×2,
lens LENS-040 Ultra long focal length projection lens, zoom window, lens cap,
To prevent accidents during lens replacement and ensure product safety after
electrical shock. This symbol indicates an action that
manual and the operation manual of the LCD projector
This can cause a fi re due to the properties of the lens. It can also
The inside of the LCD projector has areas of high voltage which
strap, lens replacement manual and option lens user's manual
strap, lens replacement manual and option lens user's manual
replacing the lens, be sure to follow the safety instructions described herein.
injury or even death if the operation is not followed correctly.
or damage to equipment if the operation is not followed correctly.
product, be sure to follow all of the safety instructions written in
Short throw lens LENS-038 Short focal length projection lens, louver, lens cap, strap×2,
Long throw lens LENS-039 Long focal length projection lens, zoom window, lens cap,
Please read this section on important safety instructions before replacing
or other strong lighting or near heat-radiating equipment.
this manual and the operation manual of the LCD projector.
lens replacement manual and option lens user's manual
lens replacement manual and option lens user's manual
lens replacement manual and option lens user's manual
To ensure safe operations and the continued safety of this
Lens Model Supplied accessories
must not be performed.
Standard projection lens Standard Lens
Fixed short throw lens LENS-037
Short throw lens LENS-038
Long throw lens LENS-039
Ultra long throw lens LENS-040
This can cause injury or damage to the lens.
The following accessories are included with each lens.
high heat.
cause injury or damage to the lens.
can cause electrical shock.
for use with this lens.
This symbol warns of possible
This can cause injury.
This symbol indicates that
the lens.
the projector lens.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.