



















IN72/IN74/IN76


and, if not installed and used in accordance with the instructions, may cause harmful
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
installation. This equipment generates, uses and can radiate radio frequency energy
interference will not occur in a particular installation. If this equipment does cause
--Connect the equipment into an outlet on a circuit different from that to which the
Other specific Country Approvals may apply. Please see product certification label.
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
harmful interference to radio or television reception, which can be determined by
InFocus reserves the right to alter product offerings and specifications at any time
turning the equipment off and on, the user is encouraged to try to correct the
provide reasonable protection against harmful interference in a residential
interference to radio communications. However, there is no guarantee that
This document applies to models IN72, P720, IN74, P740, IN76, and P760.
--Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
--Increase the separation between the equipment and receiver.
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
receiver is connected.
UL, cUL, TUV, GOST
without notice.
We declare under our sole responsibility that this projector conform to the following
Texas Instruments. Pixelworks is a trademark or registered trademark of Pixelworks
Inc. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC. InFocus, In Focus, and INFOCUS
(stylized), LP, LiteShow, LitePort, ASK and Proxima are either registered trademarks
Incorporated. Digital Light Processing is a trademark or registered trademark of
Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems
or trademarks of InFocus Corporation in the United States and other countries.
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EN 61000-3-3
directives and norms:
EN 55024


Your new InFocus projector is specifically designed for home theater appli-
DNX video processing from Pixelworks™. Whether you are watching mov-
ies or High Definition broadcasts or playing the latest video game, you will
This advanced reference guide covers all 3 models. Differences between the
included user’s guide. Optional accessories can be found on our website at
Register your projector on our website at www.infocus.com/register to acti-
vate your warranty and receive product updates, announcements, and reg-
cations. It sets a high standard using the latest DLP™ technology and new
enjoy amazing image quality. The unique design and color of the projector
To read the latest specifications, be sure to visit our website at www.info-
The standard accessories that came with your projector are listed on the
The projector is available in 3 different resolutions:
cus.com as specifications are subject to change.
www.infocus.com or at your retailer or dealer.
make it a welcome addition to your home.
Online Registration
Introduction
istration incentives.
models are noted.

to, for example, screen relay (see screen manufacturer
(not on IN72) DVI RCA
12 volt DC output
3.5mm plug
12 volt DC output
12 volt DC output The 3.5mm mini-jack trigger provides a 12 volt, 0.25 amp DC output. It pro-
vides a constant output while the projector is on. It has numerous uses. For
the screen will move down; when you turn the projector off, the screen will
with the cable that came with your screen, when you turn on the projector
example, if you connect your projection screen to the 12 volt DC output
The projector provides the following connection options:
The projector also provides the following connectors:
See “Video connectors” on page 7 for details.
return to the storage position.

Range of distance to the screen for a given screen size
Distance to the screen for a given screen size for the
60/1.5 9.3/2.8 7.8/2.4 80/2 12.3/3.8 10.4/3.2 92/2.3 14.2/4.3 12/3.7 150/3.8 23.1/7 19.5/5.9
60/1.5 8.3/2.5 6.6/2 80/2 11.1/3.4 8.8/2.7 92/2.3 12.8/3.9 10.1/3.1 150/3.8 20.8/6.3 16.4/5
lator for an interactive image size calculator.
Table 1:
Table 2:
To determine where to position the projector, consider the size and shape of
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling” on page 26. We recommend
image 10’ high, the bottom of the image will be 2.8’ above the center of
your screen, the location of your power outlets, and the distance between
power source (running extension cables may introduce a trip hazard).
from the lens of the projector to the screen, the zoom setting, and the
the projector and the rest of your equipment. Here are some guidelines:
projector must be at least 4.9 feet (1.5m) from the projection screen.
To ensure adequate cable access, do not place the projector within 6
the lens. For the IN74 and IN76, the image offset is 115%.
video format determine the size of the projected image.
Projection angle in 16:9 mode
using an InFocus authorized ceiling mount.
inches (.15m) of a wall or other object.
2.8 ft above center
10 ft high image

4:3 image input 4:3 image on 16:9 screen
letterbox image input 16:9 image fills 16:9 screen
4:3 image fills 16:9 screen
16:9 image input 16:9 image
4:3 image input
4:3 aspect ratio
16:9 aspect ratio
tion larger than the native projector resolution is cropped on the edges. Let-
What you plan to project will also help you choose between 4:3 and 16:9. For
example, most TV shows are 4:3, while most movies are 16:9. If you have a
16:9 screen, then you should select an aspect ratio of 16:9 for anamorphic movies and HDTV, and Native for 4:3 content. If you have a 4:3 screen you
should still use 16:9 for anamorphic movies or HDTV, but you also have the
mode centers the image and turns off the internal scaler so that any resolu-
option of using 4:3, Native, or Natural Wide for 4:3 content. Keep in mind
that anamorphic movies only appear correctly if the DVD player is set to
Aspect ratio is the ratio of the image width to image height. HDTV and
most DVDs are 16:9, which is the default for this projector. When in 4:3
mode the projector places black bars on both sides of the image. Native
output to a 16:9 television. Natural Wide stretches a 4:3 image to fill the
entire 16:9 screen. The center two-thirds of the image is unchanged; the
terbox expands the image to fill the screen.
edges of the image are stretched.

SCART (all 4 connectors)
(not on IN72) DVI RCA
If your device has a VGA connector, you can use the M1-DA/DVI connector
The first step for connecting video is determining what type of output con-
nectors your video device has. If there is more than one output, select the
for a high quality image. Many PC game systems have VGA connectors.
one with the highest quality. The best quality ranking, with 1 being the
1 M1-DA/DVI or HDMI (both are digital inputs)
12 volt DC output
2 component /SCART RGB video (RCAs)
4 composite video (RCA)
highest, is:

sharper detail. You must enable this connector in the Source Enable menu to
use it, see page 26. You will also need a SCART to 4-RCA adapter to connect
If your device uses component connectors, plug a component video cable
with red, green, and blue RCA connectors into the source device’s compo-
Téléviseurs) is a French-originated standard and connector for connecting
SCART (from Syndicat des Constructeurs d'Appareils Radiorécepteurs et
rated into its primary components for brighter, more accurate colors and
audio and video equipment to display devices. The video signal is sepa-
nent connectors and the Component connectors on the projector.
SCART RGB connection
to your SCART device.
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first. Exam-
ples of tuners are digital cable boxes, VCRs, digital video recorders, and sat-
ellite TV boxes. Basically, any device that can change channels is considered
A composite video cable is provided with your projector so you can quickly
image that is displayed. Once you have determined a more permanent loca-
tion for your projector, we recommend purchasing higher quality cables in
nector on the video device. Plug the other yellow connector into the yellow
projector. Connect the audio from your video device to your stereo system
Plug the composite video cable’s yellow connector into the video-out con-
If your video device uses a round, four-prong S-video connector, plug the
S-video cable into the S-video connector on your video device and into the
You can connect video devices such as VCRs, DVD players, camcorders,
the proper length to get the best image from your particular video equip-
ment. High quality cables optimized for your projector can be purchased
and easily connect a video source to the projector and see the amazing
from www.infocus.com/store (in select areas) or from your dealer or
Connecting a video device
Composite connector on the projector.
S-video connector on the projector.
to get sound.
a tuner.
retailer.

connecting an RS-232 cable to the projector’s Serial control connector. Spe-
cific RS-232 commands can be found in the Service section of our website at
HDMI provides an interface between sources, such as set-top boxes, DVD
video-out connector on the video device and into the HDMI connector on
You can connect a computer’s VGA connector to the M1-DA/DVI input on
You can control the projector from an LCD control panel or computer by
HDMI is a standard, uncompressed, all-digital audio/video interface.
players, and receivers and your projector. Plug an HDMI cable into the
ferred through HDMI will not be audible.
the projector using an M1-A cable.
the projector.
The IN76 is an HDTV (High Definition Television) monitor, meaning it has
IN72 and IN74 are EDTV (Enhanced Definition Television) monitors, mean-
cable into the video-out connector on the video device. This connector may
The M1-DA/DVI and HDMI (High-Definition Multimedia Interface) con-
these signals to be encrypted with HDCP (high-bandwidth digital-content
ing they have vertical scanning lines of 480 progressive or higher. HD con-
tent can be displayed on an EDTV monitor, the resolution is just less than
If your video device uses a DVI connector, plug the DVI end of an M1-DA
protection). Your new projector ships standard with decryption codes so
This projector uses the M1-DA connector, which has the following advan-
be labeled “To Monitor” on the video device. Plug the M1-DA end of the
nectors are digital and yield the highest quality image. It is common for
vertical scanning lines of 720 progressive, 1080 interlaced or higher. The
projector’s software as enhancements become available.
cable into the M1-DA/DVI connector on the projector.
you can enjoy these high quality, all digital images.
that of an HDTV.
tages:

plug in Power cord
turn on video device
Connect the power cord to the Power connector on the back of the projector
The LED flashes green and the fans start to run. When the lamp comes on,
? No image? Try pressing the Auto Image button on the remote. Get
the start-up screen is displayed and the LED is steady green. It can take a
doesn’t, press the Source button on the keypad until the image appears.
Position the projector the desired distance from the screen at a 90 degree
The video device’s image should appear on the projection screen. If it
See page 5 for a table listing screen sizes and distances to the screen.
Adjust the height of the image by tilting the projector up or down.
Press the Power button on the remote or keypad.
minute for the image to achieve full brightness.
Plug in, connect, and turn on your video device.
? No start up screen? Get help on page 13.
and to your electrical outlet.
help on page 13.
angle to the screen.
press Power button · adjust distance · adjust height



adjust Picture menu options
adjust zoom (outer ring)
matter what the source. However, if you wish to make further changes you
can optimize the image using onscreen menus. Adjust the Contrast, Bright-
If the image is not square, adjust the keystone using the Picture menu. See
ness, Color, Tint, or Aspect Ratio in the Picture menu. See page 22 for help
Your projector has been factory optimized for very good performance no
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information regarding Aspect Ratio, see page 6.
Adjust the volume on your stereo receiver.
with the menus and these adjustments.
Adjust the zoom and focus.
page 22 for details.

The following tables show common problems. In some cases, more than one
If your image appears correctly on the screen, skip to the next section. If it
The LED on top of the projector indicates the state of the projector and can
page 16). Turn off the projector and wait
sented. When the problem is solved, you can skip the additional solutions.
solid green The power button has been pressed and
the software has initialized or the projec-
blinking green The power button has been pressed and
the software is initializing, or the projec-
A fan or lamp failure has occurred. Make
lamp life (page 29), replace the lamp and
reset the lamp timer. Contact Technical
tor is powering down and the fans are
one minute, then turn the projector on
again. If the projector has exceeded its
possible solution is provided. Try the solutions in the order they are pre-
sure the vents aren’t blocked (see
Support if the problem persists.
tor has been powered off.
running to cool the lamp.
Technical Support.
does not, troubleshoot the setup.
see page 32 for more information
help you troubleshoot.
the projector is performed for 20 minutes. By default, this feature is on. See
The projector also has a sleep timer feature that automatically turns the pro-
minute before turning the projector on again. This allows the lamp to prop-
The lamp turns off and the LED blinks green for one (1) minute while the
fans continue to run to cool the lamp. While the LED is blinking green, the
projector does not accept any user input. Once the cooling process is com-
plete, the LED lights solid green and you can turn the projector back on, if
erly cool. The LED lights solid green when the cooling process is complete.
lamp off after no active sources are detected and no user interaction with
Press the Power button on the remote or keypad to turn the projector off.
The projector also has a Power Save feature that automatically turns the
jector off after 4 hours. See page 26.
Sleep Timer
Power Save
page 26.
desired.
LED color/behavior Meaning · blinking red


press power button correct image
no start up screen plug power cord in back of projector
press the Source button
only start up screen appears connect active source

image not centered on screen move projector, adjust zoom, adjust height correct image
Keystone in Picture menu square image
image not square tilt the projector up or down or adjust

Problem Solution Result

A B
image upside down turn off ceiling in Settings>System menu correct image
image not sharp adjust Sharpness in the Picture>Advanced


A B
menu correct image

A B
image reversed left to right turn off rear in Settings>System menu correct image
brightness, contrast in the menus correct image
lamp won’t turn on, LED blinking red make sure vents aren’t blocked, turn off the
projected colors don’t match source adjust color, tint, color temperature,
projector and allow it to cool for one

A
lamp turns on · minute

blinking red lamp must be replaced (see page 29) message disappears, LED stops blinking red
If you need assistance, visit our website at www.infocus.com or call us. See
the User’s Guide for support contact information. This product is backed by
When sending the projector in for repair, we recommend shipping the unit
in its original packing material, or having a professional packaging com-
a limited warranty. An extended warranty plan may be purchased from
pany pack the unit. Please insure your shipment for its full value.
“Change lamp” message appears at startup or LED
your retailer or dealer.
reset lamp timer · replace lamp, · Still need assistance?

the screen, not at the video device or the computer, and are within the

remote range of 30 feet (9.14m).
The remote uses two (2) provided AA batteries. They are easily installed by
projector (not at the video device or computer). The range of optimum oper-
sliding the cover off the remote’s back, aligning the + and - ends of the bat-
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
To operate, point the remote at the projection screen or at the front of the
button once to light up the remote, press and hold it to turn on the
adjust values in the menus. See page 21 for more info on the menus.
teries, sliding them into place, and then replacing the cover.
to a source button, see page 26) and a source toggle
Screen or Freeze (see page 27).
ation is up to 30 feet (9.14m).
The remote also has:
flashlight.
not dead.

Up/Down arrows–navigates to and adjusts settings in the menus (page 21).
Most buttons are described in detail in other sections, but here is an over-
Select–confirms choices made in the menus (page 21).
Menu–opens the on-screen menus (page 21).
Power–turns the projector on and off.
Source–changes the active source.
view of their functions:
menu navigation · buttons

You can customize the projector for your specific setup and needs. See
page 26 to page 28 for details on these features.
tings>System menu.
matter what the source. However, if you wish to make further changes you
width to image height. TV screens are usually 1.33:1, also known as 4:3.
press the Resize button on the remote to cycle through the options. See
can optimize the image using onscreen menus. For general information on
Your projector has been factory optimized for very good performance no
Choose the option that best fits your input source in the menus, or
HDTV and most DVDs are 1.78:1, or 16:9 (the projector’s default).
of the incoming video. Select a different standard if necessary. See
player’s user’s guide for instructions.
using the menus, see page 21.
menu (page 22).
(page 25).
page 18.
page 25.




tons, or turn the feature on or off using check boxes. Press Select to confirm
adjustments are complete, navigate to Previous or Exit, then press Select to
Certain menu items may not be visible or may be grayed depending upon a
present. For example, if the projector is set to a video source but the source,
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to high-
level, ranging from one (the Main menu) to four (the most nested menus).
particular source being connected. Differences are also seen in analog ver-
Menu options are grayed out only if the source is selected but no signal is
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio but-
your changes. Use the arrows to navigate to another setting. When your
Dots appear before the menu name. The number of dots indicate menu’s
go to the previous menu; press the Menu button at any time to close the
such as a DVD player, is turned off video menu options are grayed out.
sus digital video sources and interlaced versus progressive sources.
light the desired submenu, then press the Select button.
about the projector and source.
The menus are grouped by usage:
changed often.
menus.

increasing keystone decreasing keystone

To adjust the following settings, highlight the setting, press Select, use the
Color: adjusts a video image from black and white to fully saturated color.
TV screens are usually 4:3. HDTV and most DVDs are 16:9. The projector’s
default is 16:9. See “Choosing the aspect ratio” on page 6 for more informa-
Select Native to see the unmodified input with no resizing by the projector.
up and down arrows to adjust the values, then press Select to confirm the
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
serve the 16:9 aspect ratio. If you have a 16:9 source and screen, the image
Select 16:9 to watch enhanced widescreen DVDs. Select Letterbox to pre-
fills the screen. If your source is letterboxed, the image is expanded to fill
the screen. Select Natural Wide to stretch a 4:3 image to fill the entire 16:9
screen. The center two-thirds of the image is unchanged; the edges of the
projector up or down to adjust for keystone before using the digital key-
images. The tint setting applies to NTSC video sources only.
For more information regarding Aspect Ratio, see page 6.
Brightness: changes the intensity of the image.
stone correction in the menu.
parts of the picture.
image are stretched.
changes.
tion.
Aspect ratio · Picture menu




restored later. To restore the factory default settings, choose Factory Reset in
To set a preset for the current source, adjust the image, select Save Settings
for the input source. You can select a gamma table that has been specifically
movie; video input is material originally captured on a video camera, like a
settings in the future by selecting the appropriate user presets. All settings
tuned for either film, CRT (Cathode Ray Tube), video, PC, or Bright Room
in the Presets menu, then choose Save User 1, 2, or 3. You can recall these
input. (Film input is material originally captured on a film camera, like a
TV show or sporting event.) White Peaking increases the brightness of
in the Picture menu (except Keystone) are saved and recalled.
options and pick the one you like the best.
the Settings>Service menu.
whites that are near 100%.



such as a DVD player, is not syncing properly with the projector, adjust this
sources. It allows you to select a color space that has been specifically tuned
determines the standard. To choose a different setting, turn off Auto, then
Remember that not all options in the menus are available for all sources/
Horizontal/Vertical Position: adjusts the position of a computer source.
for the input signal. When Auto is selected, the projector automatically
choose RGB for computer sources, choose either REC709 or REC601 for
assumes the incoming signal is film material and optimizes the image
Phase: adjusts the horizontal phase of a computer source.
option to help it to sync when connected to the projector.
Tracking: adjusts the vertical scan of a computer source.
image. Select a sharpness setting.
component video sources.
accordingly.
signals.
better.
Advanced menu · Color Space · Sharpness






Native means an uncorrected/unchanged color temperature. Other values
red, green, and blue colors. These advanced controls have the same effect as
video standard options may vary depending on your region of the world.) If
look right or the image may appear “torn.” If this happens, manually select
to remove the outer 3% of the image and scale the image back up to its orig-
inal size. Select Crop to remove the outer 3% of the image without rescaling
the level. The software determines the differences between successive image
a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-
change the white point of the colors. 6500K is generally used for film con-
Color Temperature: changes the intensity of the colors. Select a value.
cally pick the video standard based on the input signal it receives. (The
the projector is unable to detect the correct standard, the colors may not
contrast and brightness, but each controls a single color only.
frames and averages the changes out to reduce the noise.
tent and 9300K is used for TV video.
dard menu.
the image.




enables the SCART RGB source. When Autosource is selected, the Source
Enable feature indicates which sources the projector attempts to lock onto.
You can use the Source Enable feature to eliminate certain sources from this
sources are checked except SCART RGB. Uncheck a source box to eliminate
to Component initially, then defaults to whatever the last active source was
selection would apply to the Custom key if that option is chosen in the Cus-
To use the SCART RGB source, you must first select it in the Source Enable
ceiling mount mode if the projector is inverted. High Power: maximizes the
“Searching”) in the lower-left corner of the screen.Translucent OSD: makes
the menus translucent. This prevents the image from being completely cov-
ered by the menus while you are making image adjustments. Sleep Timer:
cally turns the lamp off after no signals are detected for 20 minutes. After 10
signal is received before the projector powers down, the image is displayed.
it from the search. When Autosource is not checked, the projector defaults
must manually select one by pressing the Source button on the remote or
source to the Source 1, 2, and 3 buttons on the remote. The Source 4 menu
additional minutes with no signal, the projector powers down. If an active
keypad. This cycles through all the sources that are selected in the Source
light output of the lamp. Auto Power: When Auto Power is checked, the
automatically turns off the projector after 4 hours. Power Save: automati-
when the projector was powered down. To display another source, you
The Source 1, 2, and 3 menus in the Sources menu allow you to assign a
receives power. This allows control of ceiling mounted projectors with a
search, which will speed the search. By default, the check boxes for all
menu (the projector cannot automatically detect this source). Enabling
projector automatically goes into the startup state after the projector
SCART will disable Component and Composite sources.
tom key menu, see page 27.
Enable menu.


Startup Logo Blank Screen



To capture a new image, display the image and select Capture New. A mes-
the remote, allowing you to quickly and easily use the effect. Highlight an
sage appears. Select Captured in the Startup Logo menu to display your
new image. Note that this feature will not work on interlaced signals.
This gives you 4 direct source options on the remote. See page 26.
video, the source video continues to run but the image is frozen.
Screen in the Startup Logo menu and when no source is displayed.
Language: allows you to select a language for the onscreen display.
image (IN72 only) instead of the default screen at startup.
effect and press Select to choose a different one.
source information.
Custom Key · Language menu



patterns, use the up/down arrows on the remote or keypad. To exit the
Test pattern check box in the Service menu to turn the option on, exit
the menus, then press the Custom button on the remote. To select the
recognize the projector’s EDID. Uncheck this box if you have trouble
must assign Blank Screen to the Custom key (page 27), then click the
you to properly adjust the color balance with a SMPTE color bar pat-
Service: To use these features, highlight them and press Select.
Service Code: only used by authorized service personnel.
Info menu to zero. Do this only after changing the lamp.
Source Info: provides information about the active source.
Factory Reset: restores all settings to their default.
test patterns, press the Custom button.
using HDMI or DVI sources.
serial number, and lamp.
tern.
Service Info · Service menu · Source Info menu

wait 60 minutes turn off and unplug

The lamp hours timer in the Service Info menu counts the number of hours
the lamp has been in use. Twenty hours before the lamp life expires, a mes-
sage appears on the screen at startup indicating that you should change the
lamp. The LED on top of the projector also blinks red twice to indicate that
areas), your retailer or your dealer. Use only a replacement lamp with the
3 Turn the projector upside down on a soft cloth so that the lamp door is facing you. Remove the base or ceiling mount plate, if attached, by
1 Turn off the projector and unplug the power cord. If ceiling mounted, disconnect all cables and detach the projector from the ceiling mount.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
2 Wait 60 minutes to allow the projector to cool thoroughly.
same type and rating as the original lamp.
chemicals might scratch the lens.
the lamp should be changed.
removing the 3 screws.
Maintenance
Lamp hours used · projector ·

6 Detach the lamp connector from the projector by depressing the locking tab on the connector and lightly pulling it free.
7 Carefully remove the lamp housing. Dispose of the lamp in an environ- mentally proper manner.
4 Push the 2 tabs on the lamp door toward the front of the projector and lift the lamp door off.
5 Loosen the two captive screws that attach the lamp housing to the pro- jector.
unlikely event that the bulb ruptures, small glass fragments may be
9 Re-attach the lamp connector to the projector. The locking tab should engage when the connector is fully plugged in.
cleaning materials. Wash hands after lamp replacement. This prod-
uct has a lamp which contains a very small amount of mercury. Dis-
To avoid burns, allow the projector to cool for at least 60 minutes
ments, but use caution when removing the lamp housing. Before
replacing the lamp, clean the lamp compartment and dispose of
Be extremely careful when removing the lamp housing. In the
generated. The lamp housing is designed to contain these frag-
pose of it as required by local, state or federal ordinances and
regulations. For more information see www.eiae.org.
8 Install the new lamp housing and tighten the screws.
before you replace the lamp.


12 Plug in the power cord and press the Power button on the remote or keypad to turn the projector back on.
13 To reset the lamp hour timer, navigate to the Settings>Service menu and select Reset Lamp Hours. See page 28 for details.
11 Replace the base or ceiling mount plate, if necessary.
10 Replace the lamp door.
Service menu

If the projector is not functioning properly and the LED is blinking red, con-
attempts. Check the lamp and lamp door
and wait one minute, then toggle the pro-
jector on again. If the lamp does not strike
tact Technical Support for repair if replac-
Four (4) blinks The fan has failed. Contact Technical Sup-
Five (5) blinks The projector is overheating. Check for a
vents/screens does not solve the problem.
between the blinking cycles. Visit our website for more details on the red
Two (2) blinks The lamp counter hours have exceeded
Three (3) blinks The projector has shut down. Check to
see if the lamp door is open. If the lamp
after one minute, replace the lamp. Con-
ing the lamp does not solve the problem.
blocked air vent (page 16). Contact Tech-
sult Table 4 to determine a possible cause. There are two-second pauses
door is closed, toggle off the projector
lamp life hours. Replace the lamp and
nical Support for repair if clearing the
One (1) blink The lamp won't strike after five (5)
port for repair or replacing the fan.
installations for loose connections.
reset the lamp hours counter.
Red LED Behavior Explanation
LED error codes.

You can use these codes to program another remote to learn the projector’s
To activate discrete mode, press and hold the Custom button on the remote
The remote buttons are now remapped to new functions as listed below. To
for 10 seconds. The back light blinks twice when discrete mode is entered.
return to normal remote mode, press and hold the Custom button on the
remote for 10 seconds. The remote also returns to normal mode automati-
Power on turns power on Nav Down
resize selects natural wide resize auto image
16:9 resize selects 16:9 resize overscan
Power off turns power off Nav Up
User preset 1 selects user preset 1 Source 1
User preset 2 selects user preset 2 Source 2
User preset 3 selects user preset 3 Source 3
4:3 resize selects 4:3 resize source
resize selects letterbox resize custom
Native resize selects Native resize resize
Remote control discrete codes
cally if no activity is detected for 2 minutes.
remote functions.
Natural wide · Letterbox

167 40.5 24.5
Projector dimensions for ceiling mount installations
234.5 126.5
All values in millimeters (mm).

Analog Computer via M1-to-VESA cable All industry-standard analog and digi-
tal computer formats conforming to
Connector Signal Type Supported formats
Component YPrPb 480i/p/50Hz/60Hz 576i/p/50Hz/60Hz 720p/50Hz/60Hz 1080i/50Hz/60Hz 1080i/50Hz (Australia) 1080p/24 1080p/60 (sub-sampled)
HDMI Digital RGB and YCrCb 480i/50Hz/60Hz 480p/50Hz/60Hz 576i/50Hz/60Hz 576p/50Hz/60Hz 720p/50Hz/60Hz 1080i/50Hz/60Hz 1080i/50Hz (Australia)
adapter cable SCART-RGB (576i/p)
VESA standards Digital Computer via M1-to-DVI cable
M1-DA YPrPb video via M1-to-Component adapter
RGBS RGB-C or RGB-S via SCART-to-4 wire RGB
Analog RGB video via M1-to-VESA cable
Digital RGB video via M1-to-DVI cable

understood, a “?” is returned. With absolute settings, “0” is off, 1-9999 is on.
Brightness (BRT10) Sets the brightness to 10
greater than the maximum range is received, it is automatically set to the
maximum number for that function. If a command is received that is not
A read command returns the range and the current setting, for example:
Some commands have ranges, while others are absolute. If a number
#### denotes the value to be written
The one exception is the Power command, where 0 is off and 1 is on.
Lamp hours (LMP?) (0-9999, 421)
(leading zeros not necessary)
Power (PWR0) Turns power off
Power (PWR1) Turns power on
Brightness (BRT?) (0-22, 10)
AAA denotes the command
( starts the command
) ends the command
To control the projector from an LCD control panel, connect an RS-232 cable
enclosed in parentheses. The request can be a read request (indicated by a
to the serial control connector on the projector and set your computer’s
All commands consist of 3 alpha characters followed by a request, all
serial port settings to match this communication configuration:
? denotes the read request
AAA denotes the command
“?”) or a write request (indicated by 1 to 4 ASCII digits).
( starts the command
) ends the command
Bits per second 19,200
Command format

Contrast CON 0-255 128
Factory Reset (Write only) RST 0-1 n/a
Green Color Offset GCO 0-255 128
Green Gain GCG 0-255 128
Horizontal Position HPS n/a n/a
Vertical Keystone DKC 0-80 40
Display Messages DMG 0-1 1
Flesh Tone Correction FTC 0-1 0
High Power Enable HPE 0-1 0
Lamp Hours (Read only) LMP 0-65535 0
Number of Lamp Resets LMR 0-65535 0
Menu Enable MNU 0-1 0
Gamma Table GTB 0-8 2 = Video 3 = Film 5 = Bright Room 7 = CRT 8 = PC
Color Temp TMP 0-3 0 = 6500 1 = 7500 2 = 9300 3 = Native
Menu Navigation NAV 0-3 1 = up 2 = down 3 = select
Function Command Range Default
Blue Color Offset BCO 1-255 128
Blue Gain BCG 1-255 128
Brightness BRT 0-255 128
Color CLR 0-100 50
Auto Ceiling Enable ACL 0-1 0
Auto Color Space enable ACS 0-1 1
Auto Image AIM 0-1 0
Auto Power Enable APO 0-1 0
Auto Source Enable ASC 0-1 1
Auto Video Standard Enable AVS 0-1 1
Blank BLK 0-1 0
Blue Only Enable BOE 0-1 0
Ceiling CEL 0-1 0
Aspect Ratio ARZ 0-4 0 = Native 1 = 4:3 2 = 16:9 3 = Letterbox 4 = Natural Wide
Color Space CSM 0-2 0 = RGB 3 = REC709 2 = REC601
Blank Screen Enable BLK 0-1 0 = black 1 = blue
n/a

Tint TNT 2-98 50
Tracking MTS 0-100 50
Vertical Position VPS 0-100 50
Sleep Timer SLT 0-1 0
Sync Threshold Adjust STH 1-15 8
Source 1 Program SR1 0-5 0
Source 2 Program SR2 0-5 2
Source 3 Program SR3 0-5 3
Source 5 Program SR4 0-5 3
Startup Logo DSU 0-2 2
Film Mode Auto Detect TTO 0-1 1
Strike Attempts SSA 0-65535 0
Screen Trigger Enable STE 0-1 1
System State SYS 0-17 0
Translucent OSD TOE 0-1 1
Test Pattern Enable TPO 0-1 0
Test Pattern Select TPS 0-9 0
Attempts TSA 0-65535 0
Source SRC 0-5 0 = HDMI 1 = M1-DA 2 = Component 3 = S-Video 4 = Composite 5 = SCART RGB
Total number of successful
Total number of Strike
Noise Reduction Level NRL 8-248 128
Red Color Offset RCO 0-255 128
Red Gain RCG 0-255 128
Phase MSS 0-100 50
Overscan OVS 0-2 0
Power Enable PWR 0-1 0
Power Save Enable PSV 0-1 0
Rear Project REA 0-1 0
Sharpness SHP 0-4 2
Language LAN 0-11 0 = English 1 = French 2 = German 3 = Italian 4 = Japanese 5 = Korean 6 = Norwegian 7 = Portuguese 8 = Russian 9 = Chinese Simpli- fied
10 = Spanish 11 = Chinese Tra- ditional
Presets PST 0-5 0 = default 1 = User 1 2 = User 2 4 = Off
Noise Reduction Mode NRE 0-1 0 = Off 1 = Auto

Lasted LB2 0-65535 0
Lasted LB3 0-65535 0
Illuminating State LML 0-2 0
hours for all bulbs LMT 0-65535 0
Perform Lamp Reset LRT 0-1 0
been turned on O00 0-65535 0
O60 0-65535 0
O90 0-65535 0
been turned on ONC 0-4294967295 0
rently on ONL 0-4294967295 0
previously turned on ONP 0-4294967295 0
been turned on for at least
been turned on for at least
been turned on for at least
Time in minutes unit is cur-
Time in Hours Last Bulb2
Time in Hours Last Bulb3
Number of times unit has
Number of times unit has
Number of times unit has
Number of times unit has
Time in minutes unit has
Time in minutes unit was
Lamp Total Time On in
White Peaking WPK 0-10 1
Save User1 Preset US1 0-1 0
Save User 2 Preset US2 0-1 0
Save User 3 Preset US3 0-1 0
Logo Capture Enable CAP 0-1 0
Source Enable 0 CE0 0-1 0
Source Enable 1 CE1 0-1 0
Source Enable 2 CE2 0-1 0
Source Enable 3 CE3 0-1 0
Source Enable 4 CE4 0-1 0
Source Enable 5 CE5 0-1 0
Logo Capture Compress COM 0-1 0
Progress Count CPC 0-480 0
Current Subsource CRS 0-7 0
Power-up Source DSC 0-5 2
Effect Key Program EFK 0-11 8
System Error Code ERR 0-7 0
Freeze Enabled FRZ 0-1 0
Lamp Power IPM 0-1 0
Lasted LB1 0-65535 0
Video Standard VSU 0-9 0 = Auto 1 = NTSC 2 = PAL 5 = SECAM
Time in Hours Last Bulb1


Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| no start up screen | plug power cord in back of projector press power button press power button | p.22 | |
| only start up screen appears cS ta ertu np S re | connect active source press the Source button | p.22 | |
| image not centered on screen | move projector, adjust zoom, adjust height | p.23 | |
| image not square | tilt the projector up or down or adjust Keystone in Picture menu | p.23 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.