


I WORKING SESSIONS
I TRAINING
I MULTIMEDIA
I ANIMATION
I VIDEO

Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.
RAIN OR MOISTURE.
G This projector produces intense light from the projection lens. Do not stare directly into the lens as possible.
Eye damage could result. Be especially careful that children do not stare directly into the beam.
G This projector should be set in the way indicated. If not, it may result in a fire hazard.
G Take appropriate space on the top, sides and rear of the projector
SIDE and TOP REAR
cabinet for allowing air circulation and cooling the projector. Minimum distance should be taken. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.
G Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation
holes.
G Remote Control Unit, supplied to this projector, emits the laser beam as the laser pointer function from Laser
Light Window while pressing LASER button (for 1 minute / LASER POINTER INDICATOR lights red to indicate laser emission). Do not look into Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.
G If the projector is not to be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS USER'S GUIDE FOR LATER USE.
20cm · 50cm 50cm 50cm

All the safety and operating instructions should be read before the product is operated.
This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.
Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the
Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may cause hazards.
operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation. e. If the projector has been dropped or the cabinet has been
Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.
damaged. f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.
The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.
Bij dit product zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.
Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.
This is a Class A equipment. This equipment can cause interference in residential areas; in this case, the operator can be asked to take adequate countermeasures.
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.


This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.
N Digital Zoom (for Computer)
This projector is extremely compact in size and weight. It is designed to carry and work anywhere you wish to use.
Digital Zoom function adjusts image size to approx. 1/4 ~ 49 times of original image size, allowing you to focus on crucial information at a presentation.
N Compatibility
Positioning of a projector may result in distorted image being displayed in a trapezoid shape. Keystone Correction solves this problem by digitally altering projection to produce undistorted images.
This projector widely accepts various video and computer input signals including;
IBM-compatible or Macintosh computer up to 1280 x 1024 resolution.
G 6 Color Systems
Power Management function is provided to reduce power consumption while a projector is not in use. This Power Management function operates to turn Projection Lamp off when a projector detects signal interruption and any button is not pressed over 5 minutes. Projection Lamp is automatically turned on again when a projector detects signal or any operation button is pressed. This projector is shipped with this function ON.
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL- N color system can be connected.
Component video signal, such as a DVD player output high definition TV signals including 480i, 480p, 575i, 575p, 720p, 1035i or 1080i, can be connected.
S-Video signal, such as a S-VHS VCR output signal, can be connected.
This projector is equipped with DVI 24-pin terminal for connecting DVI output from a computer.
This projector provides 1024 x 768 dots resolution for computer input and 800 horizontal TV lines. Resolution from a computer between XGA (1024 x 768) and SXGA (1280 x 1024) is compressed into 1024 x 768 dots. This projector cannot display image of over 1280 x 1024 dots. When resolution of your computer is over than 1280 x 1024, reset a computer output for lower resolution.
Remote Control Unit supplied with this projector includes Laser Pointer function. This function helps you to make a smart presentation on a projected screen.
Remote Control Unit supplied with this projector has Wireless Mouse function for a connected computer. This function enables you to operate both projector and computer with Remote Control Unit only.
This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings.
Operation menu is displayed in; English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Chinese, Korean or Japanese. N One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and best adjustment is automatically set by Auto PC Adjustment. No complicated setup is necessary and projection is always precise.
Projection lens can be moved up and down with motor- driven lens shift function. This function makes it easy to provide projected image where you want. Zoom and focus can be also adjusted with motor-driven operation.
G Computers · G Component Video · G S-Video

NAME OF EACH PART OF PROJECTOR
TOP CONTROLS AND INDICATORS
PROJECTION LENS
AIR INTAKE
VENT
INFRARED REMOTE RECEIVER LENS COVER
SPEAKERS
BACK OF CABINET
POWER CORD
INFRARED REMOTE RECEIVER
CONNECTOR EXHAUST VENT
HOT AIR EXHAUSTED !
Air blown from exhaust vent is hot. When using or installing a projector, following precautions should be taken. G Do not put a flammable object near this vent. G Keep rear grills at least 3’(1 m) away from
any object, especially heat-sensitive object. G Do not touch this area, especially screws
and metallic parts. This area will become hot while a projector is used. This projector detects internal temperature and automatically controls operating power of Cooling Fans.
HANDLE
LAMP COVER
TERMINALS AND CONNECTORS
BOTTOM OF CABINET
AIR INTAKE VENTS
This projector is equipped with cooling fans for protection from overheating. Pay attention to following to ensure proper ventilation and avoid a possible risk of fire and malfunction. G Do not cover vent slots. G Keep side clear of any objects.
AND FEET LOCK LATCHES
Obstructions may block cooling air.


This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of type of power supply being in use. Connect a projector with a peripheral equipment before turning a projector on. (Refer to pages 11 ~ 13 for connection.)


For safety, unplug AC Power Cord when an appliance is not used. When this projector is connected to outlet with AC Power Cord, an appliance is in Stand-by Mode and consumes a little electric power.
Connect AC Power Cord (supplied) to a projector. AC outlet must be near this equipment and must be easily accessible.



G This projector is designed to project on a flat
ROOM LIGHT Brightness in room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide best image.
projection surface. G Projector can be focused from 4.6’ (1.4m) ~ 48.3’
(14.7m). G Refer to figure below to adjust screen size.
LENS SHIFT ADJUSTMENT Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer to P 20 for operation.



Picture tilt and projection angle can be adjusted by rotating ADJUSTABLE FEET. Projection angle can be adjusted to 10.5 degrees.
Lift front of a projector and pull FEET LOCK LATCHES on both sides of a projector. 1
Release FEET LOCK LATCHES to lock ADJUSTABLE FEET and rotate ADJUSTABLE FEET to fine tune position and tilt. 2
To shorten ADJUSTABLE FEET, lift front of a projector and pull and undo FEET LOCK LATCHES.
Position and keystone distortion of image can be adjusted using Menu Operation. (Refer to P 20 and 35.)

Use Carry Handle when moving a Projector. When moving a projector, replace lens cover and retract feet to prevent damage to lens and cabinet. When this projector is not in use for an extended period, put it into case (dust cover) supplied with this projector.

G Do not drop or bump a projector, otherwise damages or malfunctions may result. G When carrying a projector, use a suitable carrying case. G Do not transport a projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer for best way.


This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on pages 11 to 13 and connect properly.
COMPUTER AUDIO INPUT (1 and 2) JACKS
Connect an audio output (stereo) from computer to these jacks. (Refer to P12.)
USB CONNECTOR (Series B)
When controlling computer with Remote Control Unit of this projector, connect mouse port of your personal computer to this terminal. (Refer to P12.)
This projector uses a micro processor to control this unit, and occasionally, this micro processor may malfunction and need to be reset. This can be done by pressing RESET button with a pen, which will shut down and restart unit. Do not use RESET function excessively.
✽Do not press this button. This button
is used for our optional accessories.
Connect composite video output from video equipment to VIDEO/Y jack or connect component video outputs to VIDEO/Y, Cb/Pb and Cr/Pr jacks. (Refer to P13.)
Connect an audio output from video equipment to these jacks. (Refer to P13.)
Connect S-VIDEO output from video equipment to this jack. (Refer to P13.)
Connect component video output (Y, Cb, Cr or Y, Pb, Pr) from video equipment to VIDEO/Y, Cb/Pb and Cr/Pr jacks or connect computer output {5 BNC Type (Green, Blue, Red, Horiz. Sync and Vert. Sync.)} from computer to G, B, R, H/V and V jacks. (Refer to P12 and 13.)

CONNECTING TO COMPUTER
Cables used for connection (✽= Cable or adapter is not supplied with this projector.)
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
Desktop type Laptop type
Serial port PS/2 port Audio Output
Control Cable for Serial Port
MAC Adapter Set slide switches according to chart below.
for ADB Port Audio Cable ✽ (stereo)
Terminal Terminal DVI Cable ✽
COMPUTER AUDIO IN 1 or 2
Use one of these Control Cables corresponding with terminal of your computer.
COMPUTER IN ANALOG
COMPUTER IN DIGITAL
CONTROL
PORT
Terminals of a Projector
N MAC ADAPTER
Set switches as shown in table below depending on RESOLU- TION MODE that you want to use before you turn on projector and computer.
ON
2 3 4 5 6


Cables used for connection (✽= Cable is not supplied with this projector.)
AUDIO IN S-VIDEO Y - Cb/Pb - Cr/Pr VIDEO

OPERATION OF REMOTE CONTROL
Left Side
POWER ON-OFF BUTTON Used to turn projector on or off. (P19)
Lights red while laser beam is emitted from Laser Light Window.
Used to select input source. (P22)
d.zoom
MENU BUTTON Used to select MENU operation. (P17, 18)
Used to move a pointer on ON- SCREEN MENU, adjust each item, or pan image in DIGITAL ZOOM +/– mode. (P29) It is also used as a PC mouse in Wireless Mouse Operation. (P37)
Used to execute item selected, or to expand or compress image in DIGITAL ZOOM +/– mode. (P29) It is also used as a PC mouse in Wireless Mouse Operation. (P37)
✽When pressing center of this
button, it works as SELECT button.
When using Remote Control Unit, turn this switch to “on”. And turn it to “all off” when it is not used.
Used as a PC mouse in Wireless Mouse Operation. (P37)
LASER BUTTON Used to operate Laser Pointer Function. Laser beam is emitted while pressing this button within 1 minute. When using this Laser Pointer for more than 1 minute, release LASER button and press it again.
auto pc adj. image
Used to operate P-TIMER function. (P21)
This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released, light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being emitted. Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other people. Three marks bellow are caution labels for laser beam. CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result
hazardous radiation exposure.


Operating Range Point Remote Control Unit toward projector (Receiver Window) whenever pressing any button. Maximum operating range for Remote Control Unit is about 16.4’ (5m) and 60° in front and rear of a projector.
Used to adjust zoom. (P20)
VOLUME BUTTON Used to adjust volume. (P21)
FOCUS BUTTON Used to adjust focus. (P20)
d.zoom
D.ZOOM BUTTON Used to select DIGITAL ZOOM +/– mode and resize image. (P29)
MUTE BUTTON Used to mute sound.(P21)
KEYSTONE BUTTON Used to correct keystone distortion. (P20, 35)
16.4’ (5 m)
NO SHOW BUTTON Used to turn picture into black image. (P21)
FREEZE BUTTON Used to freeze picture. (P21)
IMAGE BUTTON Used to select image level. (P27, 32)
AUTO PC ADJ. BUTTON Use to operate AUTO PC Adjustment function. (P23)
auto pc adj. image
16.4’ (5 m)
LENS SHIFT BUTTON Used to select LENS SHIFT function. (P20) WIRED REMOTE JACK
When using as Wired Remote Control, connect Remote Control Cable to this jack. Battery installation is required when using as Wired Remote Control.
Remove battery compartment lid.
Slide batteries into compartment.
Replace compartment lid.
Two AA size batteries For correct polarity (+ and –), be sure battery terminals are in contact with pins in compartment.
Press lid down- ward and slide it.
To insure safe operation, please observe following precautions :
G Use (2) AA, UM3 or R06 type alkaline batteries. G Replace two batteries at same time. G Do not use a new battery with an used battery. G Avoid contact with water or liquid. G Do not expose Remote Control Unit to moisture, or heat. G Do not drop Remote Control Unit. G If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries. G Danger of explosion if battery is incorrectly replaced. G Dispose of used batteries according to batteries manufacturers instructions and local rules.

TOP CONTROLS AND INDICATORS
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.
FOCUS BUTTON
MENU BUTTON
POWER ON–OFF BUTTON
Used to adjust zoom. (P20)
Used to adjust focus. (P20)
Used to open or close MENU operation. (P17, 18)
Used to turn a projector on or off. (P19)
Used to select input source. (P22, 30)
Becomes dim when a projector is turned on. And bright when a projector is in stand-by mode.
Used to select LENS SHIFT function. (P20)
Lights green when a projector is ready to be turned on. And it flashes green in Power Management mode. (P36)
Used to select image level. (P27, 32)
Flashes red when internal projector temperature is too high. (P38)
POINT (VOLUME + / – ) BUTTONS LAMP REPLACE INDICATOR
SELECT BUTTON
Turns to yellow when life of projection lamp draws to an end. (P39)
Used to operate AUTO PC Adjustment function. (P23)
Used to select an item or adjust value in ON-SCREEN MENU. They are also used to pan image in DIGITAL ZOOM +/– mode. (P29) POINT LEFT/RIGHT buttons are also used as VOLUME +/– buttons.
Used to execute item selected. It is also used to expand / compress image in DIGITAL ZOOM mode. (P29)

OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through ON-SCREEN MENU. Refer to following pages to operate each adjustment on ON-SCREEN MENU.
POINT BUTTON
Used to move Pointer UP/ DOWN/ RIGHT/ LEFT.
1 DISPLAY MENU Press MENU button to display ON-SCREEN MENU.
Move pointer (✽see below) or adjust value of item by pressing POINT button(s) on Top Control or on Remote Control Unit.
Used to select item.
✽Pointer is icon on ON-SCREEN MENU to select item. See fig-
ures on section "FLOW OF ON-SCREEN MENU OPERATION" below.
Used to move Pointer UP/ DOWN/ RIGHT/ LEFT.
Select item or set selected function by pressing SELECT button.
Used to select item.
MENU ICON
Press MENU button to display ON-SCREEN MENU (MENU BAR). A red frame is POINTER.

POINTER (red frame) Press POINT DOWN button to move POINTER.
Select Menu to be adjusted
Move POINTER (red frame) to MENU ICON that you want to select by pressing POINT RIGHT / LEFT buttons.
Control or adjust item through ON-SCREEN MENU
Press POINT DOWN button and move POINTER (red frame or red arrow) to ITEM that you want to adjust, and then press SELECT button to show ITEM DATA.
Adjust ITEM DATA by pressing POINT RIGHT / LEFT buttons. Refer to following pages for details of respective adjustments.

ITEM DATA Press POINT LEFT/RIGHT buttons to adjust value or set function.
Display ON-SCREEN MENU · POINTER (red frame)

MENU BAR
FOR PC SOURCE Press MENU BUTTON while connecting to PC input source.
SCREEN MENU
SETTING MENU
Used to adjust size of image. [Normal / True / Wide / Digital zoom +/–] (Refer to P29) E
Used to select image level among Standard, Real and Image 1 ~ 4. (Refer to P27)
Used to change settings of projector or reset Lamp Replace Counter. (Refer to P35,-37)
PC SYSTEM MENU
Shows selected item of ON- SCREEN MENU.
Used to select computer system. (Refer to P22, 23)

PC ADJUST MENU
IMAGE ADJUST MENU
SOUND MENU
Used to select input source (Input 1, Input 2 or Input 3). (Refer to P22)
Used to adjust parameters to match with input signal format. (Refer to P23-25)
Used to adjust computer image. [Contrast / Brightness / White Balance (R/G/B) / Gamma] (Refer to P28)
Used to adjust volume or mute sound. (Refer to P21)
FOR VIDEO SOURCE Press MENU BUTTON while connecting to VIDEO input source.
IMAGE SELECT MENU
SCREEN MENU
Used to select input source (Input 1, Input 2 or Input 3). (Refer to P30)
Used to select image level among Standard, Cinema and Image 1 ~ 4. (Refer to P32)
Used to set size of image to Normal or Wide. (Refer to P34)

IMAGE ADJUST MENU
Same function as Menu for PC source.
Same function as Menu for PC source.
Used to select system of selected video source. (Refer to P31)
Used to adjust picture image. [Contrast / Brightness / Color / Tint / White balance (R/G/B) / Sharpness / Gamma/Noise Reduction/Progressive] (Refer to P33, 34)

TURNING ON / OFF PROJECTOR
TURNING ON PROJECTOR
1 Complete peripheral connections (with Computer, VCR, etc.) before turning on projector. (Refer to "CONNECTING TO PROJECTOR" on pages 11~13 for connecting that equipment.)
Input position and Lamp mode status
Connect a projector's AC Power Cord into an AC outlet. LAMP Indicator lights RED, and READY Indicator lights GREEN.
on automatically by connecting AC Power Cord to an AC outlet. (Refer to pages 35, 36.)
Press POWER ON-OFF button on Top Control or on Remote Control Unit to ON. LAMP Indicator dims, and Cooling Fans start to operate. Preparation Display appears on a screen and count-down starts. Signal from PC or Video source appears after 30 seconds. Current Input position and Lamp mode status are also displayed on screen for 5 seconds. (Refer to "LAMP MODE" on page 36.)
Preparation Display disappears after 30 seconds.
Press POWER ON-OFF button on Top Control or on Remote Control Unit, and a message "Power off?" appears on a screen.
Press POWER ON-OFF button again to turn off projector. LAMP Indicator lights bright and READY Indicator turns off. After projector is turned off, Cooling Fans operate (for 90 seconds). During this "Cooling Down" period, this appliance cannot be turned on.
3 When projector has cooled down, READY Indicator lights GREEN again and you can turn projector on. After cooling down completely, disconnect AC Power Cord.
Message disappears after 4 seconds.
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.
When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on page 35.
When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again. When WARNING TEMP. Indicator continues to flash, follow procedures below: 1. Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet. 2. Check Air Filters for dust accumulation. 3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.) 4. Turn a projector on again.
If WARNING TEMP. Indicator should still continue to flash, contact sales dealer where you purchased this projector or service center.
Input 1 · Power off?

ADJUSTING SCREEN
ZOOM ADJUSTMENT
1 Press ZOOM button on Top Control or ZOOM L/M button on Remote Control Unit. Message “Zoom” is displayed. 2 Press ZOOM L button or POINT UP button to make image larger, and press ZOOM M button or POINT DOWN button to make image smaller.
Message disappears after 4 seconds.
1 Press FOCUS button on Top Control or FOCUS L/M button on Remote Control Unit. Message “Focus” is displayed. 2 Adjust focus of image by pressing FOCUS L/M button or POINT UP/DOWN button(s) .
Message disappears after 4 seconds.
LENS SHIFT ADJUSTMENT 1 Press LENS SHIFT button on Top Control or LENS SHIFT L/M button on Remote Control Unit. Message “Lens shift” is displayed. 2 Press POINT UP button or LENS SHIFT L button to move image up, press POINT DOWN or LENS SHIFT M button to move image down.
KEYSTONE ADJUSTMENT
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
1 Press KEYSTONE button on Remote Control Unit or select Keystone on SETTING menu. (Refer to page 35.) Keystone dialog box appears. 2 Correct keystone distortion by pressing POINT UP/DOWN/LEFT/RIGHT button(s). Press POINT UP button to reduce the upper part of the image, and press POINT DOWN button to reduce the lower part. Press POINT LEFT button to reduce the left part, and press POINT RIGHT button to reduce the right part.

Reduce the upper width with POINT UP button.
Reduce the lower width with POINT DOWN button.
Reduce the left part with POINT LEFT button.
Reduce the right part with POINT RIGHT button.

PICTURE FREEZE FUNCTION
Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button except POINT / SELECT / RIGHT CLICK / LASER button.
Press BLANK button on Remote Control Unit to black out image. To restore to normal, press BLANK button again or press any other button except POINT / SELECT / RIGHT CLICK / LASER button.
Message disappears after 4 seconds.
Press P-TIMER button on Remote Control unit. Timer display “00 : 00” appears on screen and timer starts to count time (00 : 00 ~ 59 : 59). To stop P-TIMER display, press P-TIMER button. And then, press P- TIMER button again to cancel P-TIMER function.

Indicates roughly level of volume.

Press VOLUME (+/–) button(s) on Top Control or on Remote Control Unit to adjust volume. Volume dialog box appears on screen for a few seconds. (+) button to increase volume, and (–) button for decreasing.
Press MUTE button on Remote Control Unit to cut off sound. To restore sound to its previous level, press MUTE button again or press Volume (+/–) button(s).
Press MUTE button to set Mute function On or Off.
Display disappears after 4 seconds.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SOUND Menu icon.

Press POINT DOWN button to move a red frame pointer to item that you want to select, and then press SELECT button.
Indicates roughly level of volume.
To increase volume, press POINT RIGHT button, and press POINT LEFT button for decreasing.
Close SOUND Menu.
Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box display is changed to “On” and sound is cut off. To restore sound to its previous level, press POINT LEFT/RIGHT button(s) again.

SELECTING INPUT SOURCE
DIRECT OPERATION
Choose Computer by pressing INPUT button on Top Control or on Remote Control Unit. If projector cannot reproduce proper image, select correct input source through MENU OPERATION (see below).
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select Input and press SELECT button. Another dialog box INPUT SELECT Menu will appear.

Press POINT DOWN button and a red-arrow icon will appear. Move arrow to INPUT source that you want to select, and then press SELECT button.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon.

Press POINT DOWN button to move a red arrow pointer to Input 1 and then press SELECT button. Source Select Menu will appear.
Move a pointer (red arrow) to Input 1 and press SELECT button.
Move a pointer to either Digital or Analog and then press SELECT button. 3
When your computer is connected to COMPUTER INPUT (DIGITAL) terminal, select RGB (Digital). Digital
Move a pointer to Digital or Analog and press SELECT button.
When your computer is connected to COMPUTER INPUT (ANALOG) terminal, select RGB (Analog). Analog
When connect a computer output [5 BNC Type (Green, Blue, Red, Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V jacks.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon.
Move a pointer (red arrow) to Input 2 and press SELECT button.
Press POINT DOWN button to move a red arrow pointer to Input 2 and then press SELECT button. Source Select Menu will appear. 2
Press POINT DOWN button and a red-arrow icon will appear. Move arrow to "RGB", and then press SELECT button.
Move a pointer to RGB and press SELECT button.

This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to “COMPATIBLE COMPUTER SPECIFICATION” on page 26). When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually.) Note : Projector may display one of following messages.
When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and message “Auto” is displayed on SYSTEM Menu icon. When image is not provided properly, manual adjustment is required. (Refer to P24 and 25.)
Auto

PC SYSTEM Menu icon Displays system being selected.
There is no signal input from computer. Make sure connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on page 40.)
D-VGA, D-SVGA or D-XGA
When digital computer signal is received on DVI terminal, above message is displayed on PC SYSTEM Menu icon.
SELECT COMPUTER SYSTEM MANUALLY

This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually.
PC SYSTEM Menu icon Displays system being selected.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to PC SYSTEM Menu icon.
Systems on this dialog box can be selected.
Press POINT DOWN button to move a red arrow pointer to system that you want to set, and then press SELECT button.
Custom Mode (1~5) set in PC ADJUST Menu. (P24, 25)
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your computer. Auto PC Adjustment function can be operated as follows.
Auto PC Adj.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon. 1

2 Press POINT DOWN button to move a red frame pointer to AUTO PC Adj. icon and then press SELECT button twice. This Auto PC Adjustment can be also executed by pressing AUTO PC ADJ. button on Remote Control Unit.
PC ADJUST Menu icon
Move a red frame pointer to AUTO PC Adj. icon and press SELECT button.
Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, setting can be done just by selecting Mode in PC SYSTEM Menu (P23). Refer to step 3 of MANUAL PC ADJUSTMENT section (P25).
function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 24, 25.) G Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and “RGB”, “720p (HDTV)”,
“1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu.

MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall setting for a specific computer whenever you use it.
SYSTEM MENU (P23).
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon. 1

2 Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button. Adjustment dialog box will appear. Press POINT LEFT/RIGHT button to adjust value.
PC ADJUST Menu icon
Move a red frame icon to item and press SELECT button.
Adjusts an image as necessary to eliminate flicker from display. Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)
Shows status (Stored / Free) of selected Mode. Selected Mode
Number of total dots in one horizontal period. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image.

Adjusts horizontal picture position. Press POINT LEFT/RIGHT button(s) to adjust position.
Press POINT LEFT/RIGHT button to adjust value.
Adjusts vertical picture position. Press POINT LEFT/RIGHT button(s) to adjust position.
Press SELECT button at this icon to adjust “Clamp,” “Display area (H/V)” or set “Full screen.”
Press SELECT button to show information of computer selected.

Adjusts clamp position. When image has a dark bar(s), try this adjustment.

Press SELECT button at Current mode icon to show information of computer connected.



Selects area displayed with this projector. Select resolution at Display area dialog box.
Press SELECT button at Display area icon and Display area dialog box appears.
Adjustment of horizontal area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button.

Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button.
Press POINT LEFT /RIGHT button(s) to adjust value and then press SELECT button.
Press POINT LEFT/RIGHT button(s) to switch Full screen function to “On” or “Off.” Set “On” to resize image with 4 x 3 aspect ratio to fit screen.
“1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu (P23).
To store adjustment data.
This Mode has parameters being stored.

To store adjustment parameters, move a red frame pointer to Store icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store and then press SELECT button.
To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then SELECT button. Move a red arrow pointer to Mode that you want to clear and then press SELECT button.
Vacant Mode Shows values of “Total dots,” “Horizontal,” “Vertical,” “Display area H,” and “Display area V.”
Other icons operates as follows.
Reset all adjust parameters on adjustment dialog box to previous figure.
To clear adjustment data.

Closes PC ADJUST MENU.
Close this dialog box.

COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 160 MHz of Dot Clock.
DISPLAY RESOLUTION H-Freq.
V-Freq.
DISPLAY RESOLUTION H-Freq.
V-Freq.
(Hz) VGA 1 640 x 480 31.47 59.88 VGA 2 720 x 400 31.47 70.09 VGA 3 640 x 400 31.47 70.09 VGA 4 640 x 480 37.86 74.38 VGA 5 640 x 480 37.86 72.81 VGA 6 640 x 480 37.50 75.00
XGA 10 1024 x 768 62.04 77.07
XGA 11 1024 x 768
1024 x 768 (Interlace) 35.522 43.48 75.70
XGA 13 1024 x 768 XGA 14 1024 x 768
46.90 58.20
47.00 58.30
XGA15 1024 x 768
58.03 72.0
VGA 7 640 x 480 43.269 85.00
MAC 19 1024 x 768 60.24 75.08 MAC 21 1152 x 870 68.68 75.06
MAC LC13 640 x 480 34.97 66.60 MAC 13 640 x 480 35.00 66.67
SXGA 1 1152 x 864 SXGA 2 1280 x 1024
64.20 70.40 62.50 58.60 63.90 60.00 63.34 59.98
(Interlace) 15.625 25 RGB
(Interlace) 15.734 30
SXGA 3 1280 x 1024
SVGA 1 800 x 600 35.156 56.25 SVGA 2 800 x 600 37.88 60.32 SVGA 3 800 x 600 46.875 75.00 SVGA 4 800 x 600 53.674 85.06 SVGA 5 800 x 600 48.08 72.19 SVGA 6 800 x 600 37.90 61.03 SVGA 7 800 x 600 34.50 55.38 SVGA 8 800 x 600 38.00 60.51 SVGA 9 800 x 600 38.60 60.31
SXGA 4 1280 x 1024
SXGA 5 1280 x 1024 SXGA 6 1280 x 1024 SXGA 7 1280 x 1024 SXGA 8 1280 x 1024
63.74 60.01
71.69 67.19 81.13 76.107 63.98 60.02
SXGA 9 1280 x 1024 SXGA 10 1280 x 960 79.976 75.025 60.00 60.00
SXGA 11 1152 x 900
61.20 65.20
SXGA 12 1152 x 900 SXGA 13
71.40 75.60 50.00 43.00 50.00 47.00 SXGA 15 1280 x 1024 SXGA 16 1280 x 1024 SXGA 17 1152 x 900 SXGA 18
SVGA 10 800 x 600 32.70 51.09
1280 x 1024 (Interlace) SXGA 14
SVGA 11 800 x 600 38.00 60.51
1280 x 1024 (Interlace)
MAC 16 832 x 624 49.72 74.55
63.37 60.01 76.97 72.00 61.85 66.00 46.43 43.35 SXGA 19 1280 x 1024 63.79 60.18 MAC 1280 x 960 75.00 75.08 MAC 1280 x 1024 80.00 75.08
XGA 1 1024 x 768 XGA 2 1024 x 768 XGA 3 1024 x 768 XGA 4 1024 x 768
48.36 60.00 68.677 84.997
60.023 75.03
1280 x 1024 (Interlace)
56.47 70.07
XGA 5 1024 x 768 60.31 74.92
XGA 6 1024 x 768
48.50 60.02 44.00 54.58
XGA 7 1024 x 768
720p (HDTV) (Progressive) 45.00 60.00
XGA 8 1024 x 768
63.48 79.35
(Interlace) 33.75 30.00
1024 x 768 (Interlace)
36.00 43.59
(Interlace) 33.75 30.00

When a input signal is digital from DVI terminal, refer to chart below.
(Hz) D-VGA 640 x 480 31.469 59.940 D-SVGA 800 x 600 37.879 60.317 D-XGA 1024 x 768 48.363 60.004

PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote Control Unit.
Normal picture level preset on this projector.
Picture level with improved halftone for graphics.
User preset picture adjustment in IMAGE ADJUST Menu (P28).
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon. 1

2 Press POINT DOWN button to move a red frame pointer to level that you want to set and then press SELECT button.
IMAGE SELECT Menu icon
Normal picture level preset on this projector.
Move a red frame icon to level and press SELECT button.
Picture level with improved halftone for graphics.
Level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P28).

IMAGE LEVEL ADJUSTMENT
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to IMAGE ADJUST Menu icon. 1

2 Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button. Level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s).
IMAGE ADJUST Menu icon
Move a red frame pointer to item to be selected and then press SELECT button.
Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)
Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.)

Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons to adjust value.
Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.)
Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.)
Store icon Press SELECT button at this icon to store adjustment.
Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)

To store manually preset image, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to Image 1 to 4 where you want to set and then press SELECT button.
Other icons operates as follows.
Image Level Menu Move a red frame pointer to any of Image 1 to 4 where you want to set and then press SELECT button.
Reset all adjustment to previous figure.
Closes IMAGE MENU.

PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SCREEN Menu icon.

Press POINT DOWN button and move a red frame pointer to function that you want to select and then press SELECT button. 2
Move red frame to function and press SELECT button.
Provides image to fit screen size.
Provides image in its original size. When original image size is larger than screen size (1024 x 768), this projector enters “Digital zoom +” mode automatically.
when “RGB”, “1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu (P23). G Wide cannot be selected when “720p (HDTV)”,
Provides image to fit wide video aspect ratio (16 : 9) by expanding image width uniformly. This function can be used for providing a squeezed video signal at 16 : 9.
“1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu (P23). G This projector cannot display any resolution higher
than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset resolution to lower before connecting projector. G Image data in other than XGA (1024 x 768) is
When Digital zoom + is selected, ON-SCREEN MENU disappears and message “D. Zoom +” is displayed. Press SELECT button to expand image size. And press POINT UP/DOWN/LEFT/RIGHT button(s) to pan image. Panning function can work only when image is larger than screen size. A projected image can be also expanded by pressing D.ZOOM L button on Remote Control Unit.
modified to fit screen size in initial mode. G Panning function may not operate properly if
computer system prepared on PC ADJUST Menu is used.
When Digital zoom – is selected, ON-SCREEN MENU disappears and message “D. Zoom –” is displayed. Press SELECT button to compress image size. A projected image can be also compressed by pressing D.ZOOM M button on Remote Control Unit.
To cancel Digital Zoom +/– mode, press any button except D.ZOOM L/M, SELECT, POINT and AUTO PC ADJ. buttons.

SELECTING INPUT SOURCE
When connecting to those equipment, select a type of Video source in SOURCE SELECT Menu.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon. 1
Move a pointer (red arrow) to Input 2 and press SELECT button.
Press POINT DOWN button to move a red arrow pointer to Input 2 and then press SELECT button. Source Select Menu will appear. 2 E
Move a pointer to source that you want to select and then press SELECT button. 3
Move a pointer to Video or Y, Pb/Cb, Pr/Cr and press SELECT button.
When video input signal is connected to VIDEO jack, select Video. Video
When video input signal is connected to Y-Pb/Cb- Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr. Y,Pb/Cb,Pr/Cr
When connecting to those equipment, select a type of Video source in SOURCE SELECT (VIDEO) Menu.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon. 1
Move a pointer (red arrow) to Input 3 and press SELECT button. Press POINT DOWN button to move a red arrow pointer to Input 3 and then press SELECT button. Source Select Menu will appear. 2
Source Select Menu (VIDEO)
Move a pointer to source and press SELECT button.
Move a pointer to source that you want to select and then press SELECT button. 3
When video input signal is connected to VIDEO jack, select Video. Video
When video input signal is connected to Y-Pb/Cb- Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr. Y,Pb/Cb,Pr/Cr
When video input signal is connected to S-VIDEO jack, select S-Video. S-Video

SELECTING VIDEO SYSTEM
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to AV SYSTEM Menu icon.
Press POINT DOWN button to move a red arrow pointer to system that you want to select and then press SELECT button.
Projector automatically detects incoming Video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually first.

AV SYSTEM Menu icon This box indicates system being selected.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
Move pointer to system and press SELECT button.
Projector automatically detects incoming Video signal, and adjusts itself to optimize its performance. When Video System is 1035i or 1080i, select system manually first.

AV SYSTEM Menu icon This box indicates system being selected.
If projector cannot reproduce proper video image, it is necessary to select a specific component video signal format among 480i, 575i, 480p, 575p, 720p, 1035i and 1080i.
Move pointer to system and press SELECT button.
Auto · Auto

PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Cinema, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote Control Unit.
Normal picture level preset on this projector.
Picture level adjusted for picture with fine tone.
User preset picture adjustment in IMAGE ADJUST Menu (P34).
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon. 1

2 Press POINT DOWN button to move a red frame pointer to level that you want to set and then press SELECT button.
IMAGE SELECT Menu icon
Normal picture level preset on this projector.
Move red frame pointer to level and press SELECT button.
Picture level adjusted for picture with fine tone.
Level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P34).

IMAGE LEVEL ADJUSTMENT
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to IMAGE ADJUST Menu icon. 1

2 Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button. Level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s).
IMAGE ADJUST Menu icon
Move a red frame pointer to item to be selected and then press SELECT button.
Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)

Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.)
Press POINT LEFT button to lighten color, and POINT RIGHT button to deeper color. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons to adjust value.
Press SELECT button at this icon to display other items.
Press POINT LEFT button or POINT RIGHT button to obtain proper color. (From 0 to 63.)
Press SELECT button at this icon to display previous items.
Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons to adjust value.
Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.)
Press POINT LEFT button to soften image, and POINT RIGHT button to sharpen image. (From 0 to 15.)
Press SELECT button at this icon to store value.
Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)
Press POINT LEFT/RIGHT button(s) to change noise reduction mode. Dialog box display is changed to “On” to reduce noise (rough parts) of image. Press POINT LEFT/RIGHT button(s) again, to change noise reduction mode to off.
PAL-M and PAL-N systems). G S-video signal (SECAM, PAL-M and PAL-N
systems). G Component video signal. Progressive cannot be operated when “480p”, “575p”, “720p”, “1035i” or “1080i” is selected on AV SYSTEM MENU (P31).
Press POINT LEFT/RIGHT button(s) to change progressive scan mode. Dialog box display is changed to “Off” and progressive scan mode to off. Press POINT LEFT/RIGHT button(s) again, progressive scan mode to on.


To store adjustment data, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to Image Level 1 to 4 and then press SELECT button.
Image Level Menu Move a red frame pointer to image icon to be set and then press SELECT button.
Other icons operates as follows.
Reset all adjustment to previous figure.
Closes IMAGE MENU.
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SCREEN Menu icon.

Press POINT DOWN button and move a red frame pointer to function that you want to select and then press SELECT button.
Move red frame to function and press SELECT button.
Provides image at a normal video aspect ratio of 4 : 3.
“720p,” “1035i,” or “1080i” is selected on AV SYSTEM Menu (P31).
Provides image at a wide screen ratio of 16 : 9.

SETTING MENU
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red-frame pointer to SETTING icon. 1

Press POINT DOWN button to move a red-frame pointer to item that you want to set and then press SELECT button. Setting dialog box appears.
Set a red frame pointer to item and press SELECT button.
Language used in ON-SCREEN MENU is selectable from among English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Chinese, Korean and Japanese.
When image is distorted, select Keystone. ON-SCREEN MENU disappears and Keystone dialog box is displayed. Correct keystone distortion by pressing POINT UP/DOWN/LEFT/RIGHT button(s). Refer to KEYSTONE ADJUSTMENT on page 20.
When pressing SELECT button at Language, Language Menu appears.
When this function is “On,” this projector will produce a blue image instead of video noise on screen when any input source is unplugged or turned off.


This function decides whether to display On-Screen Displays.
On ··· shows all On-Screen Displays. Off sets On-Screen Displays disappeared except;
G ON-SCREEN MENU G “Power off?” message
When this function is “On,” projector displays our logo when starting up.
Move a pointer to item and then press POINT LEFT/RIGHT button(s).
When this function is “On,” picture is top / bottom and left / right reversed. This function is used to project image from a ceiling mounted projector.
When this function is “On,” picture is left / right reversed. This function is used to project image to a rear projection screen.
This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain Lamp-life. (This projector is shipped with this function ON.) Power Management function operates to turn Projection Lamp off when input signal is interrupted and any button is not pressed over 5 minutes. This function operates as follows;

Time left until Lamp off.

When this function is “On,” projector is automatically turned on just by connecting AC Power cord to a wall outlet.
“TURNING OFF PROJECTOR” on P19). If projector is turned off in wrong steps, On Start function does not operate properly.

When selecting the " " (Eco), the projector reduce the brightness and set into the low power consumption mode.
This projector has two different remote control codes; factory-set normal code (Code 1) and secondary code (Code 2). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together. When operating projector in “Code 2,” both projector and Remote Control Unit must be switched to “Code 2.” To change code of Projector; Set Remote control in SETTING MENU to “Code 2.” To change code of Remote Control Unit; Press both MENU and IMAGE buttons on Remote Control Unit together for over 10 seconds. After changing code, make sure Remote Control operates properly. To return to normal code (Code 1), operate both projector and Remote Control in ways above again. NOTE : When batteries of Remote Control Unit are replaced or ALL-
Press SELECT button at this icon to display other items.

Press SELECT button at this icon to display previous items.
Move pointer to item and then press POINT LEFT/RIGHT button(s).
OFF switch is turned to “ALL-OFF,” remote transmit code automatically returns to normal code (Code 1).
This Projector is equipped with USB port for interactive operation between a projector and computer. Set mode following steps below. Wireless Mouse mode

Press SELECT button at this icon to display previous items.
Select " " when controlling a computer with Remote Control of this projector.
Move pointer to item and then press POINT LEFT/RIGHT button(s).
Select " " when controlling a projector with computer.
(optionally sold parts) and set up computer following instruc- tion in USB driver package. Contact your authorized dealer.


This function is used to reset Lamp Replace Counter. When replacing Projection Lamp, reset Lamp Replace Counter by using this function. Refer to page 39 for operation.

Closes SETTING MENU.
Move pointer to Lamp counter reset and then press SELECT button. Message “Lamp replace counter reset?” is displayed.
Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most Personal Computers. POINT buttons and two CLICK buttons are used for wireless mouse operation. This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen. When ON- SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse function cannot be used.
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of mouse driver (not supplied) is required. Make sure that mouse driver is properly installed in your computer. And make sure that mouse port (or USB port) of a Personal Computer is activated.
Connect mouse port (or USB port) of your computer to Control Port (or USB connector) of this projector with Control Cable (or USB cable). (Refer to page 11, 12 for connection.)
port, connect Serial Port of your computer to Control Port of a projector with Control Cable for Serial Port (not supplied).
Turn a projector on first, and then turn on your computer. When computer is switched on first, Wireless Mouse may not work properly.
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK button on Wireless Remote Control Unit.
POINT button (Move pointer)
Used to move PC mouse pointer. Pointer is moved corresponding with direction you are pressing.
This button has same function as left button in a PC mouse.
This button has same function as right button in a PC mouse. This button is not available for controlling this projector.
SELECT button (left button of mouse)
RIGHT CLICK button (right button of mouse)
Lamp counter reset · Quit

MAINTENANCE
WARNING TEMP. INDICATOR
Ventilation Slots of a projector may be blocked. In such an event, reposition a projector so that Ventilation Slots are not obstructed.
Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING below.
If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be malfunctioning. Contact service personnel from an authorized dealer or a service station. 3
Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter become clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up and adversely affect life of a projector. Clean Air Filter following steps below:
Turn off a projector, and disconnect AC power cord from AC outlet.
Turn a projector upside down and remove Air Filter (2 used) by pulling latches upward.
Clean Air Filter with a brush or wash out dust and particles. 3
Replace Air Filter properly. Make sure that Air Filter is fully inserted. 4
AIR FILTER Pull up and remove.
We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments may cause poor image quality and may void the warranty.
When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements inside a projector. This condition may degrade quality of a projected image. When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.

Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.
When a projector is not in use, replace Lens Cover.

LAMP REPLACEMENT
When life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When a projected image becomes dark or color of an image becomes unnatural, replacement of Projection Lamp is required.
Follow these steps to replace lamp assembly.
Turn off a projector and disconnect AC plug. Allow a projector to cool for at least 45 minutes.
Loosen 2 screws with a screwdriver and pull out Lamp Assembly by grasping Handle.
Replace Lamp Assembly with a new one and tighten 2 screws back. Make sure that Lamp Assembly is set properly. Replace Lamp Cover and tighten 2 screws. 4
HANDLE
Connect AC Power Cord to a projector and turn it on.
Reset Lamp Replace Counter (refer to section “Lamp Replace Counter” below).
Lamp is not replaced.
ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give following information to dealer.
G Model No. of your projector : LP810/DP9295 G Replacement Lamp Type No. : Lamp No.: SP-LAMP-011
Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE Indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SETTING Menu icon (refer to page 37). 1
Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press SELECT button. Message "Lamp replace counter reset?" is displayed. Move pointer to [Yes] and then press SELECT button. 2
Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter. 3
Do not reset Lamp Replace Counter except after Projection Lamp is replaced.

TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 11 ~ 13. 2. Check cable connection. Verify that all computer, video and power cord are properly connected. 3. Verify that all power is switched on. 4. If a projector still does not produce an image, re-start your computer. 5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display. Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to turn computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and computer.) 6. If problem still exists, check following chart.
No power. G Plug a projector into your AC outlet. G Make sure READY Indicator lights. G Wait 90 seconds after a projector is turned OFF when turning a projector back on. NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as
follows: 1. LAMP indicator lights bright and READY indicator turns off. 2. After 90 seconds, READY indicator lights green again and a projector may be turned on by pressing Power ON-OFF button.
G Check WARNING TEMP. indicator. If indicator flashes red, a projector cannot be turned
on. (See "TURNING ON/OFF PROJECTOR" section on page 19.) G Check Projection Lamp. (Refer to page 39.)
Image is out of focus.
G Adjust focus of a projector. G Make sure a projection screen is at least 4.6’ (1.4m) from a projector. G Check Projection Lens to see if it needs cleaning. NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens. In such an event, leave a projector OFF and wait until condensation disappears.
Picture is Left/Right reversed.
G Check Ceiling / Rear feature. (See “SETTING” section on page 35.)
Picture is Top/Bottom reversed.
G Check Ceiling feature. (See “SETTING” section on page 35.)
Some displays are not seen during Operation.
G Check Display feature.(See “SETTING” section on page 35.)
No image. G Check connection between your computer or video equipment and a projector. G When turning a projector on, it takes about 30 seconds to display an image. G Check system that you select is corresponding with your computer or video equipment. G Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).
No sound. G Check audio cable connection from audio input source. G Adjust audio source. G Press VOLUME (+) button. G Press MUTE button.

Remote Control Unit does not work.
G Check batteries. G Check ALL-OFF switch on Remote Control Unit is set to “ON”. G Make sure nothing is between Infrared Remote Receiver and Remote Control Unit. G Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m). G Check transmitted signal mode from Remote Control Unit.
(See“SETTING” section on page 36.)
Wireless Mouse function does not work.
G Check cable connection between a projector and your computer. G Check mouse setting on your computer. G Turn a projector on before turning on a computer.
If you still need help after checking the table above, you should call your dealer's technical support line and explain your problem. If your dealer cannot solve your problem, please call InFocus Corporation's Technical Support directly at 1-800- 799-9911. Support is free between 6 a.m. and 6 p.m. PST, Monday through Friday. Support is available in North America after hours and weekends for a fee at 1-888-592-6800. Or, send us an e-mail at techsupport@infocus.com.
In Europe, call InFocus in The Netherlands at (31) 20-5792000.
In Asia, call InFocus in Singapore at (65) 6353-9449. Or, send us an e-mail at techsupport@infocus.com.
Our World Wide Web address is http://www.infocus.com
In the event that your unit is determined to be defective, you'll be issued a Return Authorization Number. After you've received this number, send the unit, a copy of your sales receipt, and a description of the problem, freight prepaid, to Proxima. Clearly note the Return Authorization Number on the outside of the shipping box.
This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).

TECHNICAL SPECIFICATIONS
Net Weight Dimensions (W x H x D)
12.6" x 6.6" x 18.5" (319 mm x 168 mm x 470 mm)
18.5 lbs (8.4 kg)
1.3" TFT Active Matrix type, 3 panels
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i and 1080i High Definition TV Signal
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
F1.7 ~ 2.0 lens with f=48.2 mm ~ 62.6 mm Motor zoom and focus Projection Lens
4.6' (1.4 m) ~ 48.3' (14.7 m) Throw distance
Adjustable from 31" to 400" Projection Image Size (Diagonal)
800 TV lines (HDTV)
275 watt type Projection Lamp
DVI Terminal (Digital), HDB 15-pin Terminal (Analog) and Stereo Mini Type Jack (Audio) Input 1 Jacks
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V), Stereo Mini Type Jack (Audio) Input 2 Jacks
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L) and DIN 4-pin (S-Video) Input 3 Jacks
DIN 8-pin (Control port), USB port (Series B receptacle) and Wired Remote Jack Other Jacks
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)
0˚ to 10.5˚ Feet Adjustment
AC 100 ~ 120 V (4.8 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada) AC 200 ~ 240 V (2.4 A Max. Ampere), 50 / 60 Hz (Continental Europe) Voltage and Power Consumption
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Power Source : AA, UM3 or R06 Type x 2 Operating Range : 16.4’ (5m) / ±30˚ Dimensions : 2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm) Net Weight : 0.36 lbs (165 g) (including batteries) Laser Pointer : Class II Laser (Max. Output : 1mW / Wave length : 650±20nm)
User’s Guide AC Power Cord Wireless/Wired Remote Control Transmitter and Batteries Remote Control Cable VGA Cable MAC/VGA Adapter 3 Types Control Cable (For PS/2, Serial and ADB port) Protective Dust Cover Lens Cover
G Specifications are subject to change without notice. G LCD panels are manufactured to the highest possible standards. At least 99.99% of the pixels are effective,
however a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
Multi-media Projector · Up and Down

CONFIGURATIONS OF TERMINALS
COMPUTER INPUT-1 TERMINAL (ANALOG) Terminal : HDB15-PIN Connect display output terminal of computer to this terminal with VGA Cable (supplied). When connecting Macintosh computer, MAC Adapter (supplied) is required.

COMPUTER INPUT-1 TERMINAL (DIGITAL) Terminal : DVI 24-pin Connect display output terminal of computer to this terminal with DVI cable (for Single Link T.M.D.S. / not supplied).

Terminal : Mini DIN 8-PIN Connect control port (PS/2, Serial or ADB port) on your computer to this connector with Control Cable (supplied).
PS/2 Serial ADB 1 2 3 4 5 6 7 8
R X D
----- ADB
----- ----- GND RTS / CTS
----- GND
3 4 5 8 7 6
----- ----- GND
----- ----- ----- GND
T X D
GND GND
USB CONNECTOR (Series B)

Connect USB port terminal on your computer or peripheral equipment to this connector with USB Cable (not supplied).
Pin Configuration

! " # $ % #
& ! " ' ! ()*( ()&* ) #
* + ' ! !#% , ' ! ! ! " ! " "% $" # Limited Warranty Alternatives: - & )+ . % / 0 2 Year Parts and Labor Product Warranty% , 1! # 0 1 Year Parts Only Accessory Warranty% ! , 2! # 0 90 Day/500 Hour Replacement Lamp Warranty %& ! ' 3 !45 ! 655 " # ! " WARRANTY LIMITATION AND EXCLUSION
78- *((*379-)7-:(783: ;-,
7 !+ ! ' ' ' # & ! # ' & !#
7* ! !" ! ! + #7& !+ + ' #
( - + ''& !# ( & ! - & % ! ! # DISCLAIMER OF UNSTATED WARRANTIES
78) *((*379(37).*>:A)-78):3&9 *((*379*& *>&)7:78-(:.; 7# *&&:78)( *((*37)-)=()--:(;73:7&9 (77)3 3-7(;93: ;-#-:

7& ! ! % 1! ! 2! * ! !#7& ! " ! ! % ! # To Be Eligible For Limited Warranty Coverage
*! + ' & ! #7 " ' * ! # To Obtain Warranty Service
. ' & ! + & ! 21 " ! @ ! D ' #
- "%2%E55%F44%4422 G# ! " ' - " " ! @ !# ' ( < * @ 3 (
! " ! /+ J " J " , J " " #; $ @ ' ! ! ' + ! ' ' ! #
3 + & ! # ! ! " !45 ! ' ' &% !" ' # LIMITATION OF LIABILITY
7-;3.)(-7::.*3.*B()).78*73: ;-,&*>&79 8)78)(3 :37(* 73 7:(7 ;3.)( *39 *((*379 3 3)B&B)3 ) :( :78)( -) -8*&& 3:7 )= )). 78) ()7;(3:78)*9;( 8*-)(*3.;3.)(3: (% ;) &*>&) :( -) *& 3.() 7 3 .)37*& :( :3-)% K;)37*&.*
-:

InFocus Corporation 27700B SW Parkway Avenue Wilsonville, Oregon 97070-9215 1-800-294-6400 G 503-685-8888 Fax: 503-685-8887 http://www.infocus.com
Part No. 010-0428-00
11/2002 610 304 0035 (1AA6P1P3748-- PK3F) Printed in Japan
Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| No power. | G Plug a projector into your AC outlet. G Make sure READY Indicator lights. G Wait 90 seconds after a projector is turned OFF when turning a projector back on. NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as follows: 1. LAMP indicator lights bright and READY indicator turns off. 2. After 90 seconds, READY indicator lights green again and a projector may be turned on by pressing Power ON-OFF button. G Check WARNING TEMP. indicator. If indicator flashes red, a projector cannot be turned on. (See "TURNING ON/OFF PROJECTOR" section on page 19.) G Check Projection Lamp. (Refer to page 39.) | p.40 | |
| Image is out of focus. | G Adjust focus of a projector. G Make sure a projection screen is at least 4.6’ (1.4m) from a projector. G Check Projection Lens to see if it needs cleaning. NOTE : Moving a projector from a cool temperature location to a warm temperature location may result in moisture condensation on Projection Lens. In such an event, leave a projector OFF and wait until condensation disappears. | p.40 | |
| Picture is Left/Right reversed. | G Check Ceiling / Rear feature. (See “SETTING” section on page 35.) | p.40 | |
| Picture is Top/Bottom reversed. | G Check Ceiling feature. (See “SETTING” section on page 35.) | p.40 | |
| Some displays are not seen during Operation. | G Check Display feature.(See “SETTING” section on page 35.) | p.40 | |
| No image. | G Check connection between your computer or video equipment and a projector. G When turning a projector on, it takes about 30 seconds to display an image. G Check system that you select is corresponding with your computer or video equipment. G Make sure temperature is not out of Operating Temperature (5°C ~ 35°C). | p.40 | |
| No sound. | G Check audio cable connection from audio input source. G Adjust audio source. G Press VOLUME (+) button. G Press MUTE button. | p.40 | |
| Remote Control Unit does not work. | G Check batteries. G Check ALL-OFF switch on Remote Control Unit is set to “ON”. G Make sure nothing is between Infrared Remote Receiver and Remote Control Unit. G Make sure you are not too far from a projector when using Remote Control Unit. Maximum operating range is 16.4’ (5m). G Check transmitted signal mode from Remote Control Unit. (See“SETTING” section on page 36.) | p.41 | |
| Wireless Mouse function does not work. | G Check cable connection between a projector and your computer. G Check mouse setting on your computer. G Turn a projector on before turning on a computer. | p.41 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.