


Simply designed to be shared

This entire user’s guide is available on the enclosed CD as an Adobe Acrobat pdf file in the following languages: English, French, German, Italian, Norwe-
gian, Portuguese, Spanish, Russian, Japanese, Korean, Traditional Chinese, Simplified Chinese. Before using this projector, please read these instructions.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Laser radiation class II product; wavelength 650nm; maximum output 1mW. Remote

Remote control complies with applicable requirements of EN 60 825-1: 1994 +A11.
control complies with applicable requirements of 21 CFR 1040.10 and 1040.11.
This Class A digital apparatus complies with Canadian ICES-003.
We declare under our sole responsibility that the LP650 projector conforms to the fol-
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
tion manual, may cause harmful interference to radio communications. Operation of
trademarks of Microsoft Corporation. InFocus, ProjectorNet, and LP are trademarks
vide reasonable protection against harmful interference when the equipment is oper-
ated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruc-
this equipment in a residential area is likely to cause harmful interference in which
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
This equipment has been tested and found to comply with the limits for a Class A
case the user will be required to correct the interference at his own expense.
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
EMC Directive 89/336/EEC, Amended by 93/68/EEC
or registered trademarks of InFocus Corporation.
Australian Certification C-tick mark
lowing directives and norms:
EN 61000-3-3
EMC: EN 55022
EN 55024

If you are experienced in setting up presentation systems, use the Quick Set
block the vents. Vents are placed along the left and right sides of the LP650,
The website also has technical specifications (an interactive image size cal-
as well as across the front of the projector. Do not use a non-approved ceil-
ing mount. In the unlikely event of the lamp rupturing, discard any edible
items placed in the surrounding area and thoroughly clean the area along
Up card that was included in the carry case. For complete details on con-
necting and operating the projector, refer to this User’s Guide. Electronic
product data sheet), a web store to buy accessories, and a page for online
Do not place the projector on a tablecloth or other soft covering that may
versions of this User’s Guide in multiple languages are available on the
culator, laptop activation commands, connector pin outs, a glossary, the
Do not place objects in the areas along the side and in the front of the projector
included CD and on our website at www.infocus.com/service.
2 ft (.6m)
2 ft (.6m) 2 ft (.6m)
the sides and in the front of the projector.
registration.
Introduction 5 Connecting a computer 7 Required computer connections 7 Displaying a computer image 9 First-time projector use with Windows 98 10 Adjusting the image 12 Connecting a video device 13 Displaying a video image 14 Shutting down the projector 16 Troubleshooting your setup 16 Using the keypad buttons 24 Using the remote control 25 Using the audio 26 Optimizing computer images 27 Presentation features 27 Optimizing video images 28 Customizing the projector 28 Using the menus 29 Picture menu 30 Settings menu 33 Maintenance 36 Cleaning the lens 36 Replacing the projection lamp 37 Using the security lock 39 Appendix 40 Specifications 40 Accessories 40 Red LED Behavior and Projector Errors 41 Projected image size 41




Cables
Your new digital projector is easy to connect, easy to use, easy to maintain
accessory items such as the projector remote, color-coded cables, documen-
tation and CD. The color-coded cable straps and cables they contain make
your setup experience quick and easy, while the case’s design helps you
find and put away all items without the fear of anything becoming lost.
Register your projector online at www.infocus.com/service/register to
The projector comes in a carry case that offers ample room for InFocus
receive product updates, announcements, and registration incentives.
and has XGA 1024x768 resolution.
* also holds business card







on the projector. Connect the blue end to the video port on your computer. If
you are using a desktop computer, you first need to disconnect the monitor
Connect the black power cable to the connector on the back of the projector
To control your computer’s mouse using the projector’s remote control, con-
nect the USB connector on the computer cable to the computer. USB drivers
must be installed to use the USB feature. For more information, see page 11.
To have sound with your presentation, connect the audio cable to your com-
Connect the black end of the computer cable to the Computer 1 connector
computer screen as well as on the projection screen, plug the monitor cable
If you are using a desktop computer and want to see the image on your
puter and to the computer Audio In connector on the projector.
The Power LED on the projector’s keypad turns solid green.
to the Monitor out connector on the projector.
Connecting a computer
cable from the computer’s video port.
and to your electrical outlet.




puter, and connect the other end of the cable to the blue Computer 2 con-
If you prefer connecting your computer to the projector with an optional
VESA cable, connect one end of the cable to the VESA port on your com-
You can control the projector from an LCD control panel or computer by
RS-232 commands can be found in the Service and Support section of our
Contact an authorized InFocus dealer or visit the ProjectorNet website at
connecting an RS-232 cable to the projector’s Serial connector. Specific
The projector can be managed by ProjectorNet networking software
www.infocus.com/projectornet for information on ProjectorNet.
website at www.infocus.com/sevice.
through its Network connector.
nector on the projector.
connect network cable · connect RS-232 cable · connect VESA cable


activate laptop’s external port
Many laptops do not automatically turn on their external video port when a
The LED flashes green and the fans start to run. When the lamp comes on,
The computer’s image should appear on the projection screen. If it doesn’t,
turn the external display on and off. Refer to your computer’s documenta-
the startup screen is displayed and the LED is steady green. It can take a
projector is connected. Usually a key combination like FN + F5 is used to
Press the Power button on the top of the projector or the remote.
? No computer image? Try pressing the Auto Image
press the Computer button on the projector’s keypad.
Make sure your laptop’s external video port is active.
minute for the image to achieve full brightness.
? No startup screen? Get help on page 17.
tion to learn your computer’s key combination.
button on the keypad. Get help on page 17.
Turn on your computer.
Remove the lens cap.
turn on computer · remove lens cap · press Power





The first time you connect a computer running Windows 98 to the projector,
If you are running Windows 2000, Windows ME, or Window XP, skip these
locates the driver. If this driver has been removed, reload the driver using
New Hardware Wizard appears. Follow these instructions to use the Wiz-
d When Windows finds the driver, you are ready to install it. Click Next.
the computer recognizes the projector as “new hardware” and the Add
ard to load the correct driver (which was installed with your Windows
c Uncheck any checked boxes, then click Next. Windows automatically
b Make sure “Search for the best driver” is selected, then click Next.
steps and go to “Adjusting the image” on page 12.
a Click Next to begin searching for the driver.
your Windows operating system CD.
operating system).
a · b · d

appears again. Drivers must be installed to use the USB functionality.
The second time a USB Human Interface Device (for the keyboard).
The third time it detects a USB Human Interface Device (for the
Skip this page if you did not connect a USB mouse cable
For Windows 2000, Windows ME, and Windows XP:
The first time it detects a USB Composite Device.
For Windows 98:
mouse).



adjust Contrast or Brightness
adjust zoom and focus
Adjust the zoom or focus rings by rotating them until the desired image size
Press the upper Keystone button to reduce the upper part of the image, and
Adjust the height of the projector, if necessary, by pressing the release but-
If the image is not square, adjust the keystone by using the buttons on the
Position the projector the desired distance from the screen at a 90 degree
press the lower Keystone button to reduce the lower part.
See page 41 for a table listing screen sizes and distances.
Adjust the Contrast or Brightness in the Picture menu.
Rotate the leveling foot, if necessary.
See page 29 for help with the menus.
ton to extend the elevator foot.
and sharpness are produced.
angle to the screen.
keypad.

R
audio in audio in
Y
R
audio in audio in
computer 1 computer 2
R
audio in audio in
computer in and video cables
computer 1 computer 2
computer 1 computer 2
R
audio in audio in
computer 1 computer 2
connect S-video and video cables
Plug the video cable’s yellow connector into the video-out connector on the
Plug a white connector into the left audio out connector on the video device
Connect the black power cable to the connector on the back of the projector
device and into the S-video connector on the projector. Use the video cable’s
If the video device uses component cable connectors (sold separately), plug
the cable’s green connectors into the green component-out connector on the
Plug the remaining white connector into the left audio in connector on the
audio connectors as described directly above (the yellow connectors on the
video device and into the green component connector (labeled “Y”) on the
projector. Plug the component cable’s blue connectors into the blue compo-
connectors into the red component-out connector on the video device and
video cable’s audio connectors as described directly above (the yellow con-
video device. Plug the other yellow connector into the yellow Video con-
and plug a red connector into the right audio out connector on the video
projector, and plug the red connector into the right audio in connector on
nent-out connector on the video device and into the blue component con-
into the red component connector (labeled “Pr”) on the projector. Use the
and to your electrical outlet. The Power LED on the keypad turns solid
If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video
nector (labeled “Pb”) on the projector. Plug the component cable’s red
nectors on the video cable are not used).
Optional video connections
video cable are not used).
nector on the projector.
the projector.
device.
green.


turn on video device
angle to the screen. See page 41 for a table listing screen sizes and distances
The LED flashes green and the fans start to run. When the lamp comes on,
Adjust the height of the projector by pressing the release button to extend
the startup screen is displayed and the LED is steady green. It can take a
Position the projector the desired distance from the screen at a 90 degree
The video device’s image should appear on the projection screen. If it
the elevator foot. Rotate the leveling foot, if necessary.
Press the Power button on the top of the projector.
minute for the image to achieve full brightness.
? No startup screen? Get help on page 16.
doesn’t, press the Video button on the keypad.
Plug in and turn on the video device.
Remove the lens cap.
to the screen.


adjust zoom and focus
Adjust the zoom or focus rings by rotating them until the desired image size
If the image is not square, adjust the keystone using the buttons on the key-
pad. Press the upper Keystone button to reduce the upper part of the
image, and press the lower Keystone button to reduce the lower part.
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.
Adjust the volume on the keypad or remote.
See page 29 for help with the menus.
and sharpness are produced.

The LED on top of the projector’s keypad indicates the state of the projector
The following tables show common problems. In some cases, more than one
solid green The projector is plugged in, or the projec-
for 2000 hours or more (page 37), replace
tact Techincal Support if the problem per-
sented. When the problem is solved, you can skip the additional solutions.
tor has been turned on and the software
blinking green The power button has been pressed and
the software is initializing, or the projec-
A fan or lamp failure has occurred. Make
page 22).Turn off the projector and wait
one minute, then turn the projector on
again. If the projector has been working
the lamp and reset the lamp timer. Con-
has initialized. The projector has been
tor is powering down and the fans are
possible solution is provided. Try the solutions in the order they are pre-
If your image appears correctly on the screen, skip to the next section
turned off and the fans have stopped.
sure the vents aren’t blocked (see
running to cool the lamp.
Technical Support.
(page 25). If it does not, troubleshoot the setup.
sists.
and can help you troubleshoot.
see page 41 for more information
The projector automatically displays a black screen after no active source is
options for the Screen Save feature. They range from five minutes to 30 min-
To turn off the projector, press the power button and verify that you want to
lights green and the fans stop. Unplug the power cable to completely power
detected for 30 minutes. This black screen helps preserve the life of the pro-
Screen Save in the Settings>System menu. See page 34. There are six time
passed. When Power Save is enabled, Screen Save is disabled. See page 34.
turn the projector off by pressing the power button again within 3 seconds.
fans continue to run to cool the lamp. When the lamp has cooled, the LED
jector. The image returns when an active source is detected or a remote or
lamp off after no signals are detected for 20 minutes. After 10 additional
minutes with no signal, the projector powers down. If an active signal is
You can cancel the shutdown by not pressing the power button a second
time. The lamp turns off and the LED blinks green for 1 minute while the
You can make the black screen appear after five minutes by turning on
The projector also has a Power Save feature that automatically turns the
received before the projector powers down, the image is displayed. You
must press the Power button to display an image after 30 minutes have
utes with five minute intervals.
keypad button is pressed.
Turning off the projector
off the projector.



No startup screen Plug power cable in and remove lens cap
Only startup screen appears

system) Computer image projected
Adjust computer refresh rate in Control
resolution on your computer, as shown
in the following Problem, “Image fuzzy
Adapter (location varies by operating
You may also need to set a different

No computer image, just the words “Signal out of

See page 25 for information on the remote
Remote controls computer cursor. Note
that the mouse is not functional in zoom

Image clear and not cropped
mode (see page 34)

Image fuzzy or cropped Set your computer’s display resolution to
mouse Connect computer cable (page 7), then,
Remote control not controlling my computer’s

A B
Image not square Adjust keystone on keypad Square image
Turn Overscan on in the Picture>Advanced
Adjust Sharpness in the Picture>Advanced


A B
Edges of image distorted

A B
Image reversed left to right Turn off Rear in Settings>System menu Correct image
Picture>Aspect ratio menu Correct image
Image upside down Turn off Ceiling in Settings>System menu Correct image

Change aspect ratio to 16:9 in


A
Image does not fit 16:9 screen

projector to cool for one minute Unplug projector; wait one minute; plug in
Check lamp hours:
Picture>Advanced menu Correct image
brightness, contrast in the menus Correct image
Projected colors don’t match source Adjust color, tint, color temperature,
Lamp won’t turn on, LED blinking red (page 16) Make sure vents aren’t blocked; allow

Video image “torn” and fragmented Change Video Standard in
AABB


provides adequate protection for shipping. Please insure your shipment for
case alone. An optional ATA shipping case is available for purchase that
Lamp won’t turn on, LED blinking red (page 16) Lamp must be replaced (page 37) Lamp turns on
Image not centered on screen Move projector, adjust zoom, adjust height Correct image
its full value.
ranty plan may be purchased from your dealer. When sending the projector
nal packing material, or having a professional packaging company pack the
in for repair, we recommend shipping the unit in the carry case in its origi-
unit with all accessories for shipping. Do not ship the projector in the carry
This product is backed by a limited two-year warranty. An extended war-
blinks · red

up/down arrows–navigates to and adjusts settings in the menus (page 29).
Most buttons are described in detail in other sections, but here is an over-
presets–cycles through the available preset settings (page 31).
power–turns the projector on (page 9) and off (page 14).
select–confirms choices made in the menus (page 29).
keystone–adjusts squareness of the image (page 12).
video and computer–changes the active source.
auto image–resets the projector to the source.
menu–opens the on-screen menus (page 29).
volume–adjusts sound (page 26).
view of their functions:
menu navigation buttons

the PowerPoint Tools menu, click the View Tab, de-select the “Popup Menu
to the next slide and a right click returns to the previous slide (other Power-
Then, when you’re in PowerPoint’s Slide Show mode, a left click advances
cable is connected. If using a USB cable, make sure the correct drivers
on Right Mouse Click” option in the Slide Show section, then click OK.
puter, and are within the remote range of 30 feet (9.14m).

Point modes are not affected).
are installed.
not dead.
To use the laser pointer, press and hold the Laser button. The laser turns off
managed via the remote’s Cursor control. Connect the USB connector on the
computer’s mouse. When you do this for the first time, the Add New Hard-
ware wizard may appear. See page 10 for details on loading the correct USB
page 16 for shutdown info), volume and mute buttons to control the sound,
to display a blank screen instead of the current slide (you can choose which
color is displayed, see page 34); use the effect button to invoke a user-defin-
able action, such as freeze or zoom (see page 34 to learn to program this but-
If you are displaying presentations in Microsoft® PowerPoint®, you can use
the remote’s mouse buttons to navigate through your presentation while in
The remote uses two (2) provided AAA batteries. They are easily installed
by sliding the cover off the remote’s back, aligning the + and - ends of the
To operate, point the remote at the projection screen or at the projector (not
at the computer). The range of optimum operation is about 30 feet (9.14m).
Press the remote’s Menu button to open the projector’s menu system. Use
a backlight button to light the remote’s buttons in the dark, and video and
Two presentation-specific features are also provided. Use the blank button
when the button is released, or times out after two (2) minutes of continu-
Left and right remote mouse buttons are used to mimic the actions of the
the arrow buttons to navigate, and the Select button to select features and
Slide Show mode. To configure PowerPoint for this, choose Options from
left/right mouse buttons on your computer. Mouse cursor movement is
computer cable to your computer to use these buttons and control your
The remote also has a power button to turn the projector on and off (see
adjust values in the menus. See page 29 for more info on the menus.
batteries, sliding them into place, and then replacing the cover.
computer buttons to switch between sources.
ous operation.
drivers.
ton).
backlight button · cursor control · navigation buttons



computer 1 computer 2 audio in
you are connected to Computer 2, be sure you are connected to its cor-
To play sound from the projector, connect your source to the Audio In con-
projector, that you are also connected to the corresponding audio in. If
power source by plugging speaker cables into the projector’s left and right
The projector can be attached to external speakers that have their own
To adjust the volume, use the buttons on the keypad or remote.
To mute the sound, press the Mute button.
If there is no sound, check the following:
on the keypad or remote.
responding audio in.
nector on the projector.
Audio Out connectors.

matically shut down the projector after several minutes of inactivity or
key. The default effect is About, which displays information about the
projector and current source. You can select from Blank, Mute, Aspect
Ratio, Source, Auto Image, Freeze, Zoom, and About. See page 34 for
ful if you want to make changes on your computer without your audi-
display a black screen. This helps preserve lamp life. See page 34 and
Several features are provided to make giving presentation easier. The fol-
lowing is an overview, details are found in the menu section on page 29.
screen to a black, white, or blue screen. See page 34.
instead of the active source. See page 34.
tor’s fan sound volume. See page 33.
ence seeing them.
details.
page 34.
After your computer is connected properly and the computer’s image is on
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
the screen, you can optimize the image using the onscreen menus. For gen-
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
save the settings using Presets. This allows you to quickly recall these
eral information on using the menus, see page 29.
input source. See page 30 for details.
settings later. See page 31.
Advanced menu.

You can customize the projector for your specific setup and needs. See
page 33 to page 36 for details on these features.
tings>System menu.
power-up.
After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general informa-
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
individually adjust the intensity of the red, green, and blue color. See
of the incoming video. Select a different standard if necessary. See
tion on using the menus, see page 29.
input source. See page 30.
menu. See page 30.
page 32.
page 32.




tons, or turn the feature on or off using check boxes. Press Select to confirm
Dots appear before the menu name. The number of dots indicate the menu’s
den when a computer source is active. Other menu items may be grayed out
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to high-
level, ranging from one (the Main menu) to four (the most nested menus).
For example, Sharpness is only available for video sources and will be hid-
when they are not available. For example, Brightness is grayed out until an
To open the menus, press the menu button on the keypad or remote. (The
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio but-
adjustments are complete, navigate to Exit, then press Select to go to the
Certain menu items may be hidden until a particular source is connected.
your changes. Use the arrows to navigate to another setting. When your
previous menu; press the Menu button at any time to close the menus.
light the desired submenu, then press the Select button.
The menus are grouped by usage:
projector and source.
changed often.
image is active.

increasing keystone decreasing keystone

To adjust the following five settings, highlight the setting, press Select, use
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
the up and down arrows to adjust the values, then press select to confirm
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or down to fill the display area.
parts of the picture and changes the amount of black and white in the
Brightness: changes the intensity of the image.
also adjust keystone from the keypad.
fully saturated color.
the changes.
image.
image.
Aspect ratio



tomize the settings for each source. The settings you customize are saved in
the preset for each source. To restore the factory default settings, choose Fac-
input is material originally captured on a film camera, like a movie; video
input is material originally captured on a video camera, like a TV show or
sporting event.) You can use the preset as a starting point, then further cus-
There are also three user-definable presets. To set a preset for the current
puter presentations, photographs, film images, and video images. (Film
source, adjust the image, select Save Settings in the Presets menu, then
choose Save User 1, 2, or 3. You can recall these settings in the future by
tory Reset in the Settings>Service menu.
selecting the appropriate user presets.
Save User Presets · Presets


Color Space Color Temperature

sources). It allows you to select a color space that has been specifically tuned
video standard options may vary depending on your region of the world.) If
look right or the image may appear “torn.” If this happens, manually select
determines the standard. To choose a different setting, turn off Auto, then
value, or select User and individually adjust the intensity of the red, green,
a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-
for the video input. When Auto is selected, the projector automatically
choose RGB for computer sources, choose either REC709 or REC601 for
video standard automatically based on the input signal it receives. (The
the projector is unable to detect the correct standard, the colors may not
Overscan: (video sources only) removes noise around the video image.
Horizontal/Vertical Position: adjusts the position of a computer source.
sources (it won’t appear in the menu for S-video or composite video
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
The following 4 options are for computer sources only.
image. Select a sharpness setting.
component video sources.
and blue colors.
dard menu.
Video Standard · Sharpness




checked, the projector defaults to the source selected in Power-up Source. If
goes into the startup state after the projector is powered on. This allows con-
speaker Volume. The Internal speakers and projector startup Chime can be
no source is found, a blank screen displays. When Autosource is checked,
power-up. If no signal is present, the projector checks the sources in order
an optional full-featured remote. Also allows selection of a default Power-
of the lamp. This also lowers the fan speed, making the projector quieter.
turned on or off by placing or removing a check in the respective check-
up Source and enables or disables Autosource. When Autosource is not
for 20 minutes. After 10 additional minutes with no signal, the projector
powers down. If an active signal is received before the projector powers
Power-up Source determines which source the projector defaults to at
Ceiling: turns the image upside down for ceiling-mounted projection.
trol of ceiling mounted projectors with a wall power switch.
checks first for active video during power-up.
“Mute”) in the lower-left corner of the screen.
until a source is found or until power down.
are made once the unit has fully warmed up.
down, the image will be displayed.
cent screen.
boxes.
mode.



an active source is detected or a remote or keypad button is pressed. Screen
enabled at a time. Highlight an effect and press Select to choose a different
nals are detected for a preset number of minutes. The image returns when
image, press the mouse right-click to decrease the magnification. You
can use the cursor control to pan the image, displaying different parts
of it (only if the image is magnified). To return to the original size and
instead of the default screen at startup and when no source is detected.
button on the remote or there is a blank screen when no source is active.
press Effect, then press the remote’s mouse left-click to zoom the
the remote to quickly and easily use the effect. Only one effect can be
Aspect Ratio: sets the ratio of the image width to image height.
About: is the default effect. It displays the About menu.
Auto Image: causes computer sources to be reacquired.
cancel Zoom, press the Effect button a second time.
Source: cycles through the available sources.
Save is disabled when Power Save is enabled.
Freeze: pauses the projected image.
Blank: shows an empty screen.
Mute: turns off all sound.
one.





work connections and TCP/IP protocols. This will allow for the control and
management of the projector over a corporate network. The following fields
are accessible when DHCP is not checked and available for manual entry of
The Network Info menu is informational and cannot be edited. It displays
the current IP Address, Subnet Mask, Default Gateway, and the projector’s
Subnet mask: Separates the network address part of the IP address.
Network Info: Provides information on the network configuration.
this only after changing the lamp. It displays a confirmation dialog box.
tings) to their default after displaying a confirmation dialog box.
Service: to use these features, highlight them and press Select.
Service Code: only used by authorized service personnel.
IP Address: Identifies the projector on the network.
Default gateway: The IP address of the local router.
and Default gateway.
menus and messages.
MAC Address.
data.

with a soft dry cloth
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you don’t intend to use the projector immediately, replace the lens cap.
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
Avoid using an excessive amount of cleaner, and don’t apply the
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
chemicals might scratch the lens.
Maintenance
and non-abrasive · clean the lens · cleaner


loosen the screw on lamp module
computer in turn off and unplug
R
audio in audio in
computer 1 computer 2
lamp has been in use. After 1,980 hours, the message “Change lamp” briefly
3 Turn the projector upside down and remove the lamp door by removing the two screws and sliding the lamp door tabs out of the three tab bays.
appears on the screen at each startup. When the timer reaches 2,000 hours,
the lamp will no longer light. You can order new lamp modules from your
The lamp hour timer in the About menu counts the number of hours the
This disrupts the air flow and causes the projector to overheat.
2 Wait 60 minutes to allow the projector to cool thoroughly.
1 Turn off the projector and unplug the power cable.
dealer. See “Accessories” on page 40 for information.
4 Loosen the captive screw on the lamp module.

reset lamp time in Service menu
event that the lamp ruptures, small glass fragments may be generated.
If the lamp timer has reached the maximum number of hours for the projec-
tor lamp (2,000 hours), the LED on the projector’s keypad will show a lamp
You can also navigate to the Settings>Service menu and select Lamp Reset
The lamp module is designed to contain most of these fragments, but
8 Replace the lamp door by sliding the tabs into the tab bays and tighten- ing the two screws.
9 Plug in the power cable, then press the Power button to turn the projec- tor back on.
error (see “LED behavior and meaning” on page 16). To reset the lamp age,
simultaneously holding down the two Volume keys on the projector’s key-
5 Carefully remove the lamp module by grasping and lifting the metal bail wire. Dispose of the lamp in an environmentally proper manner.
6 Install the new lamp module, making sure that it is properly seated.
pad for 10 seconds. At that point the LED will turn green and you can
use caution when removing it.
10 Reset the lamp hour timer.
7 Tighten the single screw.
you replace the lamp.
power on the projector.
to reset the lamp timer.
sharpness.

R
audio in audio in
computer 1 computer 2
System. See “Accessories” on page 40 for ordering information. Refer to the
The projector has a security lock for use with a PC Guardian Cable Lock
information that came with the lock for instructions on how to use it.

Optional Accessories Part Number
Shipping Case (ATA approved) CA-ATA-013
False Ceiling Plate for Projector Mount SP-LTMT-PLT
dates projector and laptop) CASE-801
(ship with the projector) Part Number
Color-coded Cable Ties, 3 set SP-CABLETIES
Shipping Box (with packaging) 110-0560-xx
Audio/Video Cable 6 ft (1.8 m) 210-0053-01
Audio Cable 6 ft (1.8 m) 210-0118-xx
Power Cable (country-dependent) 210-0023-xx
Conductor Plus Remote 590-0561-xx
Quick Setup card 009-0657-xx
User’s Guide with CD 010-0360-xx
Technical Support Contacts Card 009-0658-xx
Computer Cable 6 ft (1.8 m) SP-DVI-A
Samsonite Deluxe Travel Case (accommo-
Projection Lamp Module (included
Humidity Operating 10% to 95% relative humidity, non-condensing Non-operating 10% to 90% relative humidity, non-condensing
Dimensions 13.8 x 12.8 x 4.3” (351W x 325L x 110H mm)
Temperature Operating 50 to 95° F (10 to 35° C) at 0 - 10,000 feet Non-operating -4 to 158° F (-20 to 70° C) at 0 -20,000 feet
Ceiling Mount UL tested/listed ceiling mount with minimum capacity of
Altitude Operating 0 to 10,000 feet (3,048 meters) Non-operating 0 to 20,000 feet (6,096 meters)
Optics Focus Range 5 - 32.8 feet (1.5 - 10 meters)
Weight 9.3 lbs. (4.24 kg) unpacked
Input Power Requirements 100V-120V 4A, 50/60 Hz
200V-240V 2A 50 Hz
Lamp Type 250-watt UHP lamp
Appendix
46 lbs (20.87 kg)

Five (5) blinks The projector is overheating. Check for a
Replace the lamp. Contact Technical Sup-
port for repair if replacing the lamp does
Four (4) blinks The fan has failed. Replace the lamp (the
Technical Support for repair if replacing
blocked air vent. Contact Technical Sup-
Three (3) blinks The projector has shut down the lamp.
port for repair if clearing the air vents
Range of distance to the screen for a given screen size for LP650
lamp module contains a fan). Contact
the fan does not solve the problem.
40/1.0 32/0.8 6.9/2.1 5.0/1.5 50/1.3 40/1.0 8.7/2.6 6.2/1.9 60/1.5 48/1.2 10.4/3.2 7.5/2.3 100/2.5 79/2.0 17.4/5.3 12.4/3.8 150/3.8 119/3.0 26.0/7.9 18.7/5.7 200/5.1 158/4.0 34.7/10.6 24.9/7.6
does not solve the problem.
not solve the problem..
Table 3:
image size calculator.
If the projector is not functioning properly and the red LED is blinking, con-
attempts. Check the lamp and lamp door
Two (2) blinks The lamp counter hours have exceeded
sult Table 2 to determine a possible cause. There are two second pauses
between the blinking cycles. Visit www.infocus.com/service for more
lamp life hours. Replace the lamp and
One (1) blink The lamp won't strike after five (5)
installations for loose connections.
MindPath RF PocketPoint Remote HW-RF-POCKTPNT
reset the lamp hours counter.
84” Diagonal Wall/Ceiling Mounted Screen HW-WALLSCR84
Optional Accessories Part Number
60” Diagonal Screen (portable) HW-DLXSCRN
Replacement Lamp Module SP-LAMP-006
IR Presentation Remote Control 590-0562-xx
PC Guardian Cable Lock System SP-LOCK
Portable Projector Stand SP-STND
50” Diagonal Screen (portable) A650
Table 2:
Extension Arm for Projector Mount 26” -
details on the red LED error codes.




THIS WARRANTY SETS FORTH INFOCUS’ MAXIMUM LIABILITY FOR ITS
FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER. InFocus shall have
no further obligation under the foregoing Limited Warranty if the Product has been
damaged due to abuse, misuse, neglect, smoke exposure (cigarette or otherwise),
accident, unusual physical or electrical stress, unauthorized modifications (including
use of an unauthorized mount), tampering, alterations, or service other than by InFo-
cus or its authorized agents, causes other than from ordinary use or failure to prop-
This Warranty excludes Product or accessory cleaning, repair, or replacement of plas-
tics due to cosmetic damage and damage as a result of normal wear. Product repair
outside of the terms of the Limited Warranty will be on a time and materials basis.
Prolonged Product “demonstration” causes unusual Product wear and is not consid-
The Accessory Warranty covers the accessory item only and excludes normal wear.
Remanufactured Products and Software Products are exempt from the foregoing
Limited Warranty. Please refer to the appropriate Remanufactured Product Limited
Warranty or Software Product Limited Warranty for applicable Warranty informa-
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO
THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUD-
ING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABIL-
ITY AND FITNESS FOR PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE
NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED,
ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFO-
CUS. SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY
erly use the Product in the application for which said Product was intended.
The Lamp Product Warranty excludes expected lamp degradation.
ered normal use under the terms of this Limited Warranty.
DISCLAIMER OF UNSTATED WARRANTIES
TO YOU.
tion.
InFocus Corporation (“InFocus”) warrants that the Projector (“Product”) purchased
from InFocus, an InFocus distributor, or an InFocus reseller will conform to the man-
ufacturer's specifications and be free from defects in material or workmanship for the
Warranty period provided below. InFocus does not warrant that the Product will
If the Product, which is the subject of this Limited Warranty, is defective in material or
workmanship during the warranty period, InFocus, at its option, will REPAIR or
All exchanged parts and products replaced under this Warranty will become prop-
erty of InFocus. InFocus’ sole obligation is to supply (or pay for) all labor necessary to
repair the Product found to be defective within the Warranty period and to repair or
replace defective parts with new parts or, at the option of InFocus, serviceable used
and be free from defects in material or workmanship for a period of two (2)
manufacturers’ specifications and be free from defects in material or workmanship
Ninety (90) days or 500 hours, whichever comes first. During the Warranty period for the
Product, InFocus warrants that Replacement lamps, which are purchased at the time of projec-
tor purchase, will have a 90-day or 500 hour warranty, whichever comes first, from the date
parts that are equivalent or superior to new parts performance.
meet the specific requirements of the end-user customer.
claimers, InFocus Warrants as follows:
for a period of one (1) year.
the spare lamp is put into use.
REPLACE the Product.
years.
Limited Warranty

No repair or replacement of Product or part thereof shall extend the Limited War-
ranty period as to the entire Product. Warranty on the repair part and workmanship
shall only be effective for a period of ninety (90) days following the repair or replace-
ment of that part or the remaining period of the Product Limited Warranty whichever
IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY WHETHER IN
CONTRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHER-
WISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PUR-
CHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES
SHALL INFOCUS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CON-
SEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR LOST SAV-
INGS. THE PRICE STATED FOR THE PRODUCTS IS A CONSIDERATION IN
Limitation on Bringing Action - No action, regardless of form, arising out of the
agreement to purchase the product may be brought by purchaser more than one year
Governing Law - Any action, regardless of form, arising out of the agreement to
Mandatory Arbitration - Any action, regardless of form, arising out of the agree-
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS,
ment to purchase the product is subject to mandatory arbitration.
purchase the product is governed by Oregon law.
after the cause of action has accrued.
LIMITING INFOCUS’ LIABILITY.
DEPENDING ON JURISDICTION.
is greater.
The Limited Warranty period commences on the date of purchase by the end-user
customer for both the 2 year Product Warranty and the 1 year Accessory Warranty.
These Limited Warranty provisions shall apply only to the end-user purchaser (first
person or entity that purchased a new Product for personal or business use and not
Any person exercising a claim under this Limited Warranty must establish to the sat-
isfaction of InFocus both the date of purchase and that the Product was purchased
new. The sales receipt or invoice, showing the date of purchase of the Product or
During the Limited Warranty period, to exercise this Limited Warranty, the purchaser
must first contact 1) InFocus, 2) a service facility authorized by InFocus or 3) the place
For Warranty service, the purchaser will be advised to return or deliver the defective
Product freight and all fees prepaid, to an InFocus Service Center or to a service facil-
ity authorized by InFocus. When returning Product to InFocus, a Return Material
Authorization Number (RMA #) is required and must be clearly displayed on the out-
side of the shipping carton or a similar package affording an equal degree of protec-
tion. InFocus or the service facility authorized by InFocus will return the repaired/
Products returned for Warranty service must be accompanied by a written letter that:
(i) explains the problem; (ii) provides proof of date of purchase; (iii) provides the
dealer’s name; and (iv) provides the model and serial number of the Product. Upon
request of InFocus Corporation or an InFocus authorized repair center receiving the
Product, proof of legal importation must accompany the warranty repair Product,
otherwise the Product must be returned to the place of original purchase, to the man-
ufacturer (Purchaser must bear all tax, duty and freight), or the Purchaser must bear
InFocus Customer Service - 1-800-799-9911 or techsupport@infocus.com
To Be Eligible For Limited Warranty Coverage
replaced Product freight prepaid to the purchaser.
Accessory is the proof of the date of purchase.
for the purpose of distribution or resale).
To Obtain Warranty Service
charges for the warranty repair.
of original purchase.
Limited Warranty Period
Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| No startup screen | Plug power cable in and remove lens cap press power button | p.18 | |
| No startup screen | p.18 | ||
| No startup screen | Press the Computer button Activate laptop’s external port | p.18 | |
| Image not square | Adjust keystone on keypad | p.21 | |
| Edges of image distorted A B | Turn Overscan on in the Picture>Advanced menu | p.21 | |
| Image not sharp A B | Adjust Sharpness in the Picture>Advanced menu | p.21 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.