

Please read these instructions carefully before using your projec- tor. Failure to comply with them could result in fire, electrical shock, personal injury or damage to equipment.
These graphics are used throughout this manual to draw your attention to important information about the projectors.
These graphics are used on the projector’s labels.
safety information.
Do not touch until the projector has cooled.
Do Not Look Into The Lens! Be extremely careful not to look into the projection lens when the projector is turned on. The bright light may harm your eyes. Be especially careful to keep children from looking into the lens.
Power Source Use only a three-wire grounding type power source. The power source should not exceed 250 volts rms between the supply con- ductors or between either conductor and the ground.
Power Cord Use only the power cord that was shipped with the projector. Although other power cords might be similar in appearance, they have not been safety-tested with the projector. Do not use a power cord if it has become damaged or frayed. Contact your In Focus dealer or call In Focus if you need to replace your power cord.

S a f e t y S u m m a r y
Grounding The projector is grounded through the grounding conductor on the power cord. To avoid electric shock, plug the power cord into a properly wired receptacle. Do not defeat the purpose of the grounding-type plug.
Lamp To avoid overheating and unacceptable image quality, replace the projection lamp with a lamp of the specified type. Refer to page 49 for lamp specifications and to page 41 for instructions on replacing the lamp.
Lamp Compartment To avoid burns, do not open the lamp module door until the pro- jector is turned off and the lamp has cooled for at least 2 minutes. Follow the instructions in this manual for lamp replacement care- fully.
Hot Surfaces Allow the projector to cool at least 2 minutes before replacing a lamp. When you open the lamp housing, be very careful not to touch the hot surfaces inside.
Ventilation and Overheating Openings in the projector case provide ventilation to protect it from overheating. Keep loose papers and other objects well away from the grills. Do not place the projector on top of or close to a computer or other heat-producing equipment.
Liquid Spills Do not set drinks on top of the projector. Spilled liquids can flow inside and cause damage.
Do Not Disassemble All projector service must be performed by an authorized In Focus service center. The only user-serviceable part in the projec- tor is the projection lamp, which you can replace by opening the lamp cover on the bottom of the projector (see page 41). Do not open any other part of the projector. If your projector needs repair, call In Focus Technical Support as described on page 5. Before you call Technical Support, you may want to refer to “Troubleshooting” on page 44 to see if you can resolve the prob- lem yourself.
case, you will void the warranty.

The In Focus® LP™ 725 and 730 lightweight multimedia projec- tors combine powerful and sophisticated features with easy-to- use, intuitive controls. Built-in multimedia features include audio, a palette of 16.7 million colors and active matrix liquid crystal display (LCD) technology. The 700 series projectors are ideal for high-performance business, training and imaging appli- cations that demand exceptional color quality. The 725 has SVGA 800x600 graphics, the 730 has XGA 1024x768 graphics. The user interfaces of the two products are identical; information in this User’s Guide applies to both products.
expands 640x480 images to
LP 725 The SVGA resolution of the 725’s projected image is 800x600. Screen resolutions between 800x600 and 1024x768 are com- pressed to 800x600. The 725 cannot compress screen resolutions above 1024x768. If your computer’s screen resolution is higher than 1024x768, reset it to a lower resolution before you connect the 725.
800x600. You can display these
images at 640x480 by turning off
the Auto Resize feature. See “Auto
Resize” on page 35 for more infor-
mation.
The XGA resolution of the 730’s projected image is 1024x768. Screen resolutions between 1024x768 and 1280x1024 are com- pressed to 1024x768. The 730 cannot compress screen resolutions above 1280x1024. If your computer’s screen resolution is higher than 1280x1024, reset it to a lower resolution before you connect the 730.
expands 640x480 and 800x600
images to 1024x768. You can dis-
play these images at their original
resolutions by turning off the Auto
Resize feature. See “Auto Resize”
on page 35 for more information.

I n t r o d u c t i o n
The projector is compatible with a wide variety of computers and video devices, including:
also supported. Contact your In
Focus dealer for details.
The projector comes with the items shown in Figure 1. Check to make sure all are included. Contact your In Focus dealer immedi- ately if anything is missing.
If you are experienced in setting up presentation systems, use the LP 725/730 Quick Start card that was included in the shipping box. For complete details on connecting and operating the projec- tor, refer to this User’s Guide. User’s Guides are also available for download from our website at www.infocus.com
shipping box may vary depending
on the configuration you’ve
ordered.


Shipping box contents

I n t r o d u c t i o n
Side view of projector
power cord connector focus ring zoom ring
Front view of projector

and turns off, you must wait about
30 seconds before you attempt to
turn it back on.
The first place to look for help is in this manual. Be sure to check the guidelines in “Troubleshooting” on page 44.
If this manual doesn’t answer your question, call your In Focus dealer. You can also call In Focus Customer Service directly at 1-800-799-9911. Customer Service is free between 5 a.m. and 5 p.m. PST, Monday through Friday. Service is available in North America after hours and on weekends for a fee. In Europe, call In Focus in The Netherlands at (31) 23-5540310. In Singapore, call (65) 740-6435. Or, send us an e-mail at techsupport@infocus.com
Our World Wide Web address is http://www.infocus.com.
This product is backed by a limited one-year warranty. The details of the warranty are printed at the back of this manual. Longer term warranties can be purchased from your In Focus dealer. Refer to page 52 for part numbers.

1 Place the projector on a flat surface.
cable, sold separately, lets you
increase the distance between the
projector and your computer to
70 feet (21 m). See “Optional
Accessories” on page 52.
2 Position the projector the desired distance from the screen.
3 Make sure the projector and your computer are turned off.
25 ft.
5 ft.
2.5 ft.
3.3 ft. 6.5 ft. 32.5 ft.
Projected image size (minimum focusing distance)

S e t t i n g u p t h e P r o j e c t o r
The CableWizard simplifies the connection process by providing a central hub for all the connections between the projector and your computer. The connectors on the CableWizard are labeled with icons.
computer, monitor and projector
whenever you connect or
Connect the end of the CableWizard cable to the
disconnect cables.
connector on the projector’s connector panel (Figure 5).

optimized for use with
CableWizard II. If you have
CableWizards from other models
of In Focus projectors, we do not
recommend using them. Image
quality is reduced by using a
CableWizard other than Cable
Wizard II. The label on the bottom
Connecting the CableWizard to the projector
CableWizard II.
Turn the selector on the top of the CableWizard to reveal the correct connectors for your computer.

cables before turning the selector
on the CableWizard.
Selecting connectors on the CableWizard
reads CableWizard or

provided for use with a command
center for a fixed installation.
Selecting the IBM-compatible connectors on the CableWizard
Selecting the Macintosh connectors on the CableWizard

S e t t i n g u p t h e P r o j e c t o r
Now you’re ready to connect your equipment. Computers are connected to the CableWizard. Video players and other equip- ment, such as external speakers, are connected directly to the pro- jector.
make sure the projector and your
equipment are turned off. If you’re
Steps for connecting the different types of equipment are given on the pages listed below.
connecting a computer, make sure
the distance between it and the
projector is 10 feet or less and
Equipment you want to connect Page
you’ve selected the appropriate
IBM-compatible laptop computer page 11
connectors on the CableWizard.
IBM-compatible desktop computer page 13
Apple PowerBook page 15
Macintosh desktop computer page 17
Video player page 19
External speaker page 21
the monitor connector does not
have a hole for Pin 9. If you have
CableWizard computer cable to
your computer, contact In Focus
Technical Support.
CableWizard wired remote external
speaker s-video composite video

1 Plug the end of the CableWizard computer cable into the video connector on your computer.
2 Plug the end of the CableWizard computer cable into the
connector on the CableWizard.
do not automatically turn on their

external video port when a sec-
ondary display device such as a
projector is connected. Refer to
your computer manual for the
command that activates the exter-
nal video port. Activation com-
mands for some laptop computers
are listed in the Appendix of this
manual on page 53.
Connecting the CableWizard computer cable to an IBM-compatible laptop computer
Do you want to play your computer’s audio on the projector?
1 Plug either end of the CableWizard audio cable into the audio connector on your computer.
mouse control, you can use the
CableWizard Lite with your IBM-
2 Plug the other end of the audio cable into the connector on the CableWizard.
compatible computer. CableWiz-
ard Lite is ordered separately. See
page 52.
“Optional Accessories” on

S e t t i n g u p t h e P r o j e c t o r
Do you want to control the computer’s mouse from the projector’s remote or keypad?
1 Locate the mouse cable and unplug it from your computer.
2 Plug the end of the CableWizard mouse cable into the mouse connector on your computer.
do not allow you to use the
3 Plug the end of the CableWizard mouse cable into the connector on the CableWizard.
computer’s pointing device and the
projector’s remote at the same
time.

Connecting the CableWizard audio and mouse cables to an IBM-compatible laptop computer
Now you’re ready to power up the projector and your laptop. Skip to “Powering up the Projector and Adjusting the Image” on page 21.
audio cable

1 Locate the cable that connects your monitor to your computer. Unplug it from the computer.
2 Plug the end of the CableWizard computer cable into the monitor connector on your computer.
3 Plug the end of the computer cable into the connector on the CableWizard.

Connecting the CableWizard computer cable to an IBM-compatible desktop computer
Do you want to display the image on your computer’s monitor as well as on the projection screen?
1 Plug your monitor’s cable into the connector on the CableWizard.
Do you want to play your computer’s audio on the projector?
1 Unplug the audio cable, if present, from your computer.
2 Plug either end of the CableWizard audio cable into the audio connector on your computer.
3 Plug the other end of the audio cable into the connector on the CableWizard.

S e t t i n g u p t h e P r o j e c t o r
Do you want to control your computer’s mouse from the projector’s remote or keypad?
1 Unplug the mouse cable from your computer.
2 Plug the end of the CableWizard mouse cable into the mouse connector on your computer.
computer’s mouse and the
3 Plug the end of the CableWizard mouse cable into the connector on the CableWizard.
projector’s remote at the same
time.

Connecting the CableWizard monitor, audio and mouse cables to an IBM-compatible desktop computer
Now you’re ready to power up the projector and your computer. Skip to “Powering up the Projector and Adjusting the Image” on page 21.
audio cable

1 Plug the end of the CableWizard computer cable into the video connector on your PowerBook.
2 Plug the end of the CableWizard computer cable into the
connector on the CableWizard.
the Apple-supplied video-out cable
3 If you want the projector display to be the same as the Power- Book’s screen display, turn on video mirroring. (See “Using Video Mirroring with a PowerBook Computer” on page 57 for additional information.)
for external video. Connect it
between the PowerBook and the
CableWizard computer cable as
shown in Figure 14.

Connecting the CableWizard computer cable to an Apple PowerBook
Do you want to play your computer’s audio on the projector?
1 Plug either end of the CableWizard audio cable into the audio connector on your PowerBook.
2 Plug the other end of the audio cable into the connector on the CableWizard.

S e t t i n g u p t h e P r o j e c t o r
Do you want to control the computer’s mouse from the projector’s remote or keypad?
1 Locate the mouse cable and unplug it from your PowerBook.
2 Plug the end of the CableWizard mouse cable into the (ADB) connector on your PowerBook.
do not allow you to use the
3 Plug the end of the CableWizard mouse cable into the connector on the CableWizard.
computer’s pointing device and the
projector’s remote at the same
time.

Connecting the CableWizard audio and mouse cables to a PowerBook
Now you’re ready to power up the projector and your Power- Book. Skip to “Powering up the Projector and Adjusting the Image” on page 21.
audio cable

1 Locate the cable that connects the monitor to your computer. Unplug it from the computer.
2 Plug the end of the CableWizard computer cable into the monitor connector on your computer.
3 Plug the end of the CableWizard computer cable into the
connector on the CableWizard.

Connecting the CableWizard computer cable to a Macintosh desktop computer
Do you want to display the image on your computer’s monitor as well as on the projection screen?
1 Plug the monitor’s cable into the connector on the CableWizard.
Do you want to play your computer’s audio on the projector?
1 Unplug the audio cable, if present, from your computer.
2 Plug either end of the CableWizard audio cable into the audio connector on your Macintosh.
3 Plug the other end of the audio cable into the connector on the CableWizard.

S e t t i n g u p t h e P r o j e c t o r
Do you want to control the computer’s mouse from the projector’s remote or keypad?
1 Unplug the mouse from your Macintosh or locate an unused ADB connector.
2 Plug the end of the CableWizard mouse cable into the
mouse connector or the (ADB) connector on your Macintosh.
computer’s mouse and the
projector’s remote at the same
3 Plug the end of the CableWizard mouse cable into the connector on the CableWizard.
time.

Connecting the CableWizard monitor, audio and mouse cables to a Macintosh desktop computer
.Now you’re ready to power up the projector and the Macintosh. Skip to “Powering up the Projector and Adjusting the Image” on page 21.
audio cable

1 If your video player uses a round, one-prong composite video connector, you’ll need only the A/V cable that shipped with the projector.
2 Plug the A/V cable’s yellow connector into the “video-out” port on your video player (Figure 18). This port may be labeled “To Monitor.”
3 Plug the other yellow connector into the composite connector on the projector.
Connecting the projector to a video player using the standard A/V cable (with composite
audio/video cable · video connector)

S e t t i n g u p t h e P r o j e c t o r
Connecting the projector to a video player using an S-video cable and the audio con- nectors on the standard A/V cable
4 Plug the A/V cable’s white connector into the left “audio out” port on your video player. Plug the cable’s red connector into the right “audio out” port on the video player (Figure 18 and Figure 19).
may also have a “Video Out” port
5 Plug the A/V cable’s other white and red connectors to the left and right “audio in” ports on the projector.
for a coaxial cable connection.
DO NOT use this to connect to the
The projector is compatible with these major broadcast video standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, and SECAM. It automatically adjusts to optimize its performance for the incoming video. The input signals for SECAM, PAL-M, and PAL-N video cannot be automatically detected, therefore they must be chosen manually; see “Video Standard” on page 37.
projector.
S-video cable · A/V cable

To connect one or two external speakers, plug the speaker cable
into the (audio out) connector on the projector.
must be amplified.
Connecting an external speaker
1 Remove the lens cap.
2 Plug the power cord into the front of the projector, then plug it into your electrical outlet. A surge-protected power strip is recommended if power surges are common in your area.
that shipped with the projector.
3 Turn on the projector by pressing the “I” side of the power switch on the front of the projector.
4 If you connected a video player, turn it on.
remains solidly lit after the projec-
tor has powered on, the lamp
needs to be replaced. Refer to
“Replacing the Projection Lamp”
on page 41 for more information.

S e t t i n g u p t h e P r o j e c t o r
5 If you connected any external speakers, turn them on.
6 If you connected your monitor, turn it on.
7 Turn on your computer.
the order in which you power up
the equipment is very important.
Most computers should be turned
on last, after all other peripherals
have been turned on. Refer to your
determine the correct order.
If you want to turn off the projector for a short period of time, press the standby button on the keypad. This blanks the screen for 15 minutes, but keeps the projector running. After 15 minutes, the lamp goes out (the projector keeps running). To exit standby mode, press the standby button again. (It takes several seconds for the projection lamp to reach full power and project the image again.)
To completely power off the projector, press the “O” side of the power switch on the front of the projector. If you want to turn the projector back on immediately, you must allow about 30 seconds for the lamp to cool. The lamp won’t light if it’s too hot.
disconnect the projector after you
have switched it off, always
remove the power cord from the
electrical outlet first, then remove
it from the projector.
computer’s documentation to

This section describes how to use and make adjustments to the projector. It also provides a reference to the keypad buttons and the options available from the on-screen menus.
1 Make sure you have powered up your equipment in the right order (page 21).
software program called In Focus
2 If the image doesn’t display completely, adjust the height and tilt of the projector (page 25), zoom the image (page 25), or center the image by adjusting its horizontal or vertical posi- tion (page 36).
Presents that automatically opti-
mizes your computer’s display
when used with any In Focus pro-
jector. This free program is
3 If the image is out of focus, rotate the lens to focus it (page 25).
included with every projector and
4 If the image appears to shimmer or if it has blurry vertical bars after you have adjusted the focus, turn Auto Image (page 35) off and then back on to reset the automatic sync and tracking. If that doesn’t clear up the image, adjust the sync (page 36) and/or the tracking (page 36) manually.
available for download from our
website at www.infocus.com
5 If the colors don’t look right, adjust the brightness (page 27) and tint (page 31).
Point the remote control at the projection screen or at the front or rear of the projector. The range for optimum operation is about 40 feet. If you point the remote at the projection screen, the dis- tance to the screen and back to the projector must be less than or equal to 40 feet. For best results, point the remote directly at the front or the rear of the projector.
remote control at the projector so
that its signal is received — for
example, when using rear projec-
tion — purchase the optional
The projector ships with a two-button remote. (A full-feature Smart Remote with all the same buttons as the keypad is avail- able separately; see “Optional Accessories” on page 52.) The remote has a disk mouse and two mouse buttons, one on the top of the remote and one on the bottom.
Smart Remote and connect it
directly to the projector with the
optional remote control cable. See
page 52.
“Optional Accessories” on

U s i n g t h e P r o j e c t o r
(on underside of remote)
Press anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button; the button on the bottom simulates your computer’s left mouse but- ton.
If you are creating presentations in Microsoft® PowerPoint®, you can use the remote’s mouse buttons to navigate through your presentation while in Slide Show mode. To configure PowerPoint for this, choose Options from the Tools menu, click the View Tab, de-select the “Popup Menu on Right Mouse Click” option in the Slide Show section, then click OK. Then, when you’re in Power- Point’s Slide Show mode, a left click advances to the next slide and a right click returns to the previous slide (other PowerPoint modes are not affected).
mouse from the projector’s remote
or keypad, you must connect the
mouse cable to the CableWizard.
See page 10 for details.

To focus the image, rotate the focus ring (Figure 22) until the image is clear. To zoom the image, rotate the zoom ring. This adjusts the image size without affecting focus.
focus ring zoom ring
Focus ring, zoom ring, and elevator button
The projector is equipped with a self-locking, quick-release eleva- tor foot and button (Figure 24) and a leveling knob (Figure 23).
elevator button · Leveling knob

U s i n g t h e P r o j e c t o r
To raise the projector:
1 Press and hold the elevator button (Figure 22).
2 Raise the projector to the height you want, then release the button to lock the elevator foot into position.
3 If necessary, use the leveling knob (Figure 23) to adjust the angle of the projected image.
Adjusting the height of the projector
To lower the projector:
1 Press the elevator button.
2 Lower the projector.
3 If necessary, use the leveling knob (Figure 23) to readjust the angle of the projected image.

This section provides an alphabetical reference to the keypad but- tons.

Brightness Adjusting the brightness lightens or darkens the image.
Computer When you have more than one source (computer or LiteShow Pro and video) connected to the projector, select between them by pressing the button for the source you want.
optional presentation player. Con-
tact your In Focus dealer for more
Press computer to display your computer image or LiteShow Pro presentation.
information.
Freeze The freeze button halts, or “freezes” the projected image. Use this button to freeze a frame of video (the video continues to run but the projected image is frozen). You can also freeze an image from a computer source on the screen, allowing you to perform other operations on the computer without the audience seeing them. Press freeze again when you want the image to return to normal.
Help Press help to display the on-screen help information.
Keypad

U s i n g t h e P r o j e c t o r
Menu Press menu to open the on-screen menus. Press menu again to close the menus. When you close the menus, the projector saves any changes you made. For more information about the on- screen menus, see page 29.
Mute Pressing the mute button silences the internal speaker. It also silences any external speakers that are connected.
To return the volume to its previous setting, press mute again or press either volume button.
Scribble The scribble button activates on-screen annotation.
1 Press the scribble button. The cursor changes to a pencil.
2 Press the right disk mouse button (Figure 26 on page 30) to display the color selector. Use the disk mouse to position the cursor on the desired color, then press the left mouse button. Press the right button again to close the color selector.
3 Use the disk mouse to move the pencil to where you want to start the annotation.
4 Press the left mouse button. The cursor changes to an upright pencil.
5 Use the disk mouse to draw your annotation. Press the left mouse button to complete the annotation.
6 To exit Scribble, press the scribble button. The annotation is automatically deleted (it cannot be saved).

Standby When you press standby, the display and audio turn off and a blank screen is displayed for 15 minutes. After 15 minutes, the lamp goes out if you haven’t pressed standby again. You can change the amount of time the projector stays in standby mode; see “Standby TIme” on page 37 for details.
Video When you have more than one source (computer or LiteShow Pro and video) connected to the projector, select between them by pressing the button for the source you want.
Press video to display the image from your video player.
Volume adjustments are saved for each source you have con- nected.
The projector has four on-screen menus that allow you to make image adjustments and change a variety of settings. Most of these adjustments aren’t available directly from the keypad.
To open the on-screen menus, press the menu button on the key- pad. Press menu again when you want to close the menus and save any changes.
To select a menu, use the disk mouse on the keypad or remote to move the cursor to the tab for the menu you want, then click either mouse button.
Volume

U s i n g t h e P r o j e c t o r
left mouse right mouse button button
Disk mouse and mouse buttons on keypad
To change a menu setting, move the cursor to the setting you want to change, then use one of the two mouse buttons to make changes. All changes are saved when you close the menus.
The status bar at the top of the menu display indicates the source that is currently active (Computer or Video) and any peripherals that are connected.
The status bar also contains a lamp hour counter that starts at zero hours and counts each hour the lamp is in use. When the counter reaches 2000 hours, the lamp monitor light turns on, when it reaches 2050 hours, the lamp switches off completely. See “Replacing the Projection Lamp” on page 41 for details.

disk mouse


Adjusting the brightness changes the intensity of the image.
using the menu is the same as
changing it using the keypad.
Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
Tint The tint adjusts the red-green color balance in the projected image. Changing the Tint setting has no effect on PAL or SECAM video sources.
Display menu · Brightness

U s i n g t h e P r o j e c t o r
Color The color setting adjusts a video image from black and white to fully saturated color.
Blank Screen Blank Screen determines what color is displayed when there is no active source and when the projector is in standby. Click the but- ton to toggle between the two options.
Reset All Click either mouse button to reset all the options (except Lan- guage, Video Standard, Ceiling, and Rear Projection) in all the menus to their original settings. This also returns Freeze and Mute to their default (off) settings.
Menu Position This lets you move the menu to various locations on the screen, allowing you to view different parts of the image while making adjustments. The default position is the center of the screen. Click Menu Position to move the menu to the upper-left corner; click it again to move it to upper-right, then lower right, then lower left, then center again.


from the menu is the same as
Volume adjustments you make are saved for each source.
changing it using the keypad.
Balance The balance setting controls the balance between the left and right external speakers. It appears gray and won’t highlight if you haven’t connected external speakers. Balance applies to all sources you have connected.
Audio menu · Volume

U s i n g t h e P r o j e c t o r
Fade The fade setting controls the balance between the internal and external speakers. The setting appears gray and won’t highlight if external speakers aren’t connected.
Treble The treble setting controls the higher frequencies of your audio source.
settings apply only to the
Bass The bass setting controls the lower frequencies of your audio source.
projector’s internal speaker.
External speakers typically have
their own tone controls.


The projector automatically adjusts tracking, signal synchroniza- tion and vertical and horizontal position for most computers. If you want to adjust these features manually, you must turn off Auto Image first by clicking it.
fere with the operation of Auto
Image. If you’re experiencing prob-
Auto Resize Auto Resize automatically resizes the image by scaling it up or down.
lems, try turning your screen saver
off, then turning Auto Image off
and back on.
When Auto Resize is on, the projector makes the best fit of the image to the screen. If you turn Auto Resize off (by clicking it), the image may be either cropped or too small for the screen.
Image menu · Auto Image

U s i n g t h e P r o j e c t o r
Manual Sync The projector adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy or streaked, try turning Auto Image off then back on again. If the image still looks bad, try adjusting the signal synchronization manually as described below.
1 Click the Auto Image button to turn Auto Image off.
2 Press the left or right mouse buttons repeatedly until the image is sharp and free of streaks.
Manual Tracking The tracking function adjusts the projector to match the video signal from your computer. The projector usually adjusts the tracking automatically when you connect your computer. How- ever, if the display shows evenly spaced, fuzzy, vertical lines or if the projected image is too wide or too narrow for the screen, try turning Auto Image off then back on again. If the image is still bad, try adjusting the tracking manually as described below.
Manual Tracking, Horiz.
Position and Vert. Position
buttons are available only for
computer sources. The projector
sets these options automatically
1 Click the Auto Image button to turn Auto Image off.
for a video source.
2 Press the left or right mouse buttons repeatedly until the fuzzy vertical bars are gone.
Horiz. Position Follow these steps to manually adjust the horizontal position.
1 Click the Auto Image button to turn Auto Image off.
2 Press the left mouse button to move the image right; press the right mouse button to move the image left.
Positioning adjustments are saved when you power off the pro- jector.
Vert. Position Follow these steps to manually adjust the vertical position.
1 Click the Auto Image button to turn Auto Image off.
2 Press the left mouse button to move the image down; press the right mouse button to move the image up.
Positioning adjustments are saved when you power off the pro- jector.


When Auto is on, the projector attempts to pick the video stan- dard (NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, or SECAM) auto- matically based on the input signal it receives. (The video standard options may vary depending on your region of the world.) The input signals for SECAM, PAL-M, and PAL-N video cannot be automatically detected, therefore they must be chosen manually. If the projector is unable to detect the standard, the col- ors might not look right or the image might appear “torn.” If this happens, manually select a standard by clicking the button and cycling through the standards.
video standard used in your geo-
graphical area, it’s often best to
manually select it.
Standby TIme This option lets you select how long the lamp stays on and the blank screen is displayed when you enter standby mode before the projector turns off. Select among 1, 5, 10, and 15 minutes by clicking the button and cycling through the options.
Controls menu · Video Standard

U s i n g t h e P r o j e c t o r
Language You can display the on-screen menus in English, French, German, and Spanish. The default is English.
Series Ceiling Mount, refer to
Rear Projection When you select Rear Projection, the projector reverses the image so you can project from behind a translucent screen.
page 52.
Default Source Default Source toggles between Computer and Video. This deter- mines which source the projector checks first for active video during power-up. Click the button to toggle between the options.
Auto Source Select This setting toggles between On and Off. When this feature is Off, the projector defaults to the source selected in Default Source. To display another source, you must manually select one by press- ing the computer or video button on the keypad. When this fea- ture is On, the projector automatically finds the active source, checking the default source first. Click the button to toggle between the options.
Ceiling · “Optional Accessories” on

This section describes how to:
Follow these steps to clean the projection lens:
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
2 Lightly wipe the cleaning cloth over the lens.
3 If you don’t intend to use the projector immediately, replace the lens cap.
The fan intake filter on the bottom of the projector catches dust and particles in the air. If the filter becomes clogged, the projector does not cool properly and may malfunction. To prevent this, clean the filter after every 100 hours of use.
1 Turn off the power and unplug the power cord.
2 Remove the filter door.

M a i n t e n a n c e & T r o u b l e s h o o t i n g
Removing the filter door
3 Clean the filter.
Cleaning the air filter
4 Replace the filter.

The lamp hour counter on the status bar at the top of the menus counts the number of hours the lamp has been in use. After 2000
hours of use, the lamp monitor LED, marked on the top of the projector near the keypad, lights. After 2050 hours, the lamp switches off completely and must be replaced. You can order new lamp modules from your In Focus dealer. See “Accessories” on page 51 for information.
allow the projector to cool for at
least 2 minutes before you open
the lamp module door. Never
extract the lamp module while the
lamp is operating.
Follow these steps to replace the projection lamp:
1 Turn off the projector and unplug the power cord.
2 Wait 2 minutes to allow it to cool thoroughly.
3 Using a small, flat-blade screwdriver, remove the screw on the outside of the lamp door (Figure 34).
4 Pull the lamp cover up and remove it.
Removing the lamp module door
5 Loosen the two non-removable screws on the outside of the module.
6 Remove the module (Figure 35).
projector with the lamp cover open
or removed. This disrupts the air
flow and causes the projector to
overheat.

M a i n t e n a n c e & T r o u b l e s h o o t i n g
Removing the lamp module
7 Align the new lamp module in the correct direction.
8 Gently push the module in as far as it goes (Figure 36).
lamp module or touch the glass
9 Tighten the screws on the outside of the module.
bulb! The glass may shatter and
cause injury.
Installing a new lamp module
10 Reposition the lamp cover.

11 Replace the screw and tighten it.
12 Plug in the power cord and turn the projector back on. The lamp monitor light and lamp hour counter in the Status bar on the menus are automatically reset.
The life of the batteries depends on how often and how long you use the remote. Symptoms of low battery charge include erratic responses when using the remote and a reduced range of opera- tion.
Follow these steps to replace the batteries:
1 Turn the remote face down in your hand.
2 Slide the battery cover off the end of the remote by pressing on it with the heel of your hand.
3 Remove the old batteries.
4 Install two new AAA alkaline batteries. Make sure you install each in the correct direction.
5 Slide the battery cover back on the remote.
The projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System (Figure 37). Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector.
Installing the Kensington lock

M a i n t e n a n c e & T r o u b l e s h o o t i n g
If you’re experiencing trouble with the projector, follow these steps to make sure everything is properly connected before you call Technical Support for assistance.
1 Check cable connections. Verify that all computer, CableWiz- ard and power cables are properly connected.
2 Verify that all power is switched on.
3 Verify that the projector has not been switched off with the standby button on the keypad.
4 If the projector still doesn’t display an image, restart the com- puter.
5 If the problem still exists, unplug the projector from the com- puter and check the computer monitor’s display. The maxi- mum resolution that the 725 can display is 1024x768 pixels, preferably 800x600; the maximum resolution that the 730 can display is 1280x1024 pixels, preferably 1024x768. The problem might be with the graphics controller in your computer rather than with the projector. When you reconnect the projector, remember to turn the computer and monitor off before you power up the projector. Power the equipment back up in this order: projector, monitor, computer.
require a specific power-up
turned on before you turn on the
computer.
6 If you’re using a laptop computer and it is not displaying your presentation, make sure you have activated the computer’s external video output. Most laptop computers do not auto- matically turn on their external video port when a secondary display device such as a projector is connected. Refer to page 53 for more information.
7 If the problem still exists, read through the problems and solu- tions in this chapter.

Problem: Nothing on projection screen • Make sure that the power cord is properly connected to a func- tional AC electrical outlet. Make sure that the power cord is also properly connected to the projector.
Problem: Color or text not being projected • You might need to adjust the brightness up or down until the text is visible. Refer to “Brightness” on page 27 for more infor- mation.
Problem: The screen resolution is not right • Make sure the computer’s graphics card is set for a resolution of no greater than 1024x768 for the 725, 1280x1024 for the 730.
Problem: Image isn’t centered on the screen • Reposition the image. Refer to “Horiz. Position” on page 36 and “Vert. Position” on page 36.
Problem: Only the start-up screen displays • Verify that the cables are connected correctly. Check to see that the CableWizard computer cable is correctly connected to the monitor connector on the computer (this is the connector where your monitor cable usually goes.) See page 8 through page 17 for connection procedures.

M a i n t e n a n c e & T r o u b l e s h o o t i n g
If you’re using Windows 3.x:
1 In the Windows Program Manager, double-click the Win- dows Setup icon in the Main program group.
2 Verify that the Display setting is 1024x768 or less for the 725, 1280x1024 or less for the 730.
If you’re using Windows 95:
1 Open “My Computer” icon, the Control Panel folder and then the Display icon.
2 Click the Settings tab.
3 Verify that the Desktop area is set to 1024x768 or less for the 725, 1280x1024 or less for the 730.
Also check the following:
Problem: Image is too wide or narrow for screen • You might need to manually adjust the tracking to reduce or enlarge the projected image. Refer to “Manual Tracking” on page 36.

Problem: Image is out of focus • Turn the projection lens to focus the image.
Problem: Image and menus are reversed left to right • Rear projection mode is probably turned on. Switch back to for- ward projection from the Controls menu. The image should immediately return to forward projection. See “Rear Projec- tion” on page 38.
Problem: Image and menus are upside down • Ceiling mode is probably turned on. Turn off the mode from the Controls menu. The image should immediately return to forward projection. See “Ceiling” on page 38.
Problem: the projector displays vertical lines, “bleeding” or spots • Adjust the brightness. See “Brightness” on page 27.
Problem: no sound • Press the mute button.
Problem: Image is “noisy” or streaked Try these steps in this order.
1 Deactivate the screen saver on your computer.
2 Turn Auto Image off and then back on again. See “Auto Image” on page 35.
3 Adjust the synchronization and tracking manually to find an optimal setting. See “Manual Sync” on page 36 and “Manual

M a i n t e n a n c e & T r o u b l e s h o o t i n g
Tracking” on page 36.
Problem: Projected colors don’t match the computer or video player’s colors • Adjust the brightness, tint and/or contrast from the Display menu. Just as there are differences in the displays of different monitors, there are often differences between the computer image and the projected image. See “Brightness” on page 27, “Tint” on page 31 and “Contrast” on page 31.
Problem: Lamp seems to be getting dimmer • The lamp begins to lose brightness when it has been in use for a long time. Replace the lamp as described in “Replacing the Pro- jection Lamp” on page 41.
Problem: Lamp shuts off • A minor power surge may cause the lamp to shut off. Turn the projector off, wait at least 30 seconds, then turn it back on.
Problem: Remote not operating correctly • You might need to replace the batteries. See “Replacing the Bat- teries in the Remote Control” on page 43.
Before calling your dealer or In Focus Technical Support for assis- tance, please have the following information available::
Call In Focus Technical Support at 1-800-799-9911. Support is free between 5 a.m. and 5 p.m. PST, Monday through Friday. Support is available in North America after hours and on weekends for a fee.

Specifications
The LP 725 and 730 must be operated and stored within the tem- perature and humidity ranges specified.
Temperature Operating 10 C to 40° C Non-operating -20 to 70° C
Humidity Operating and non-oper. 5% to 95% relative humidity, non-condensing
Dimensions 6.0 x 15.3 x 11.7 inches (15.3 x 38.8 x 29.8 cm)
Weight 12.2 lbs. (5.5 kg) unpacked
Altitude Operating 0 to 10,000 feet (3048 meters) Non-operating 0 to 40,000 feet (12,192 meters)
Audio Output Frequency Response 10 Hz - 20 KHz Output Impedance 1.2 K ohm nominal Output Voltage 2 Vrms maximum (open circuit) Connector Type red and white RCA jacks
Optics Focus Range 3.25 - 32.5 feet (1-10 m)
Lamp Type 150-watt UHP

A p p e n d i x
Remote Control Battery Two (2) AAA alkaline cells
Input Power Requirements 100-120/220-240V, 5.0/3.0A, 50/60 Hz.
Video Audio Input Input Impedance 5K ohm DC coupled Maximum Input Voltage (LIN + RIN)PEAK < 4.5 V for THD ≤ 0.3% LIN or RIN < 2.0 Vrms for THD ≤ 0.3%
Sensitivity 100 mV at 1 KHz for 88 dB SPL at 1 meter Connector Type RCA jack
CableWizard Audio Input Input Impedance 10K ohm nominal, AC coupled Maximum Input Voltage (LIN + RIN)PEAK < 4.5 V for THD ≤ 0.3% LIN or RIN < 2.0 Vrms for THD ≤ 0.3%
Sensitivity 100 mV at 1 KHz for 88 dB SPL at 1 meter Connector Type 3.5 mm (1/8 inch) stereo phone jack

Standard Accessories (ship with the projector) Part Number
LP 725/730 Quick Start card 009-0342-xx
LP 725/730 User’s Guide 010-0151-xx
CableWizard and Cables SP-CW2
CableWizard Audio Cable 210-0079-xx
CableWizard Computer Cable 210-0094-xx
CableWizard Mouse Cable 210-0078-xx
Projection Lamp Module SP-LAMP-LP7E
Remote Control and 2 Batteries SP-EXREM
Online User’s Guide CD-ROM 010-0116-xx
Power Cords (one ships with projector, type depends on country)
North American Power Cord 210-0023-xx
approved accessories. Other prod-
Australian Power Cord 210-0027-xx
ucts have not been tested with the
UK Power Cord 210-0028-xx
projector.
European Power Cord 210-0029-xx
Danish Power Cord 210-0030-xx
Swiss Power Cord 210-0031-xx
Shipping Box 110-0159-xx · Lens Cap 505-0241-xx · Audio/Video Cable 210-0053-xx

A p p e n d i x
Easy Carry Case CA-C129
European Hard Case CA-C130
Hard Travel Case CA-C123
Deluxe Travel Case CA-C128
ATA Shipping Case CA-C124
CableWizard Lite, 6.5 ft (2 m) SP-CW2LITE
Mac Adapter for CableWizard Lite 516-0003-xx
CableWizard Extension Cable, non-plenum rated, 60.7 ft (18.5 m)
CableWizard Extension Cable, plenum-rated, 60.7 ft (18.5m) SP-CW2EXTP
Full-Feature Smart Remote Control HW-SMART
LiteShow Pro Presentation Player HW-LSPRO
LiteShow Pro Soft Case CA-C131
32 MB Memory Upgrade HW-MEM-LSP
Kensington MicroSaver Security System SP-KENLOC
SGI/SUN Workstation Cables SP-CABLE-WS
Rhapsody II Speakers SP-R2SPKR
Portable Projector Stand SP-STND
LP 700 Series Ceiling Mount-LiteMount 7 SP-CEIL-LM7
LiteMount False Ceiling Plate SP-LTMT-PLT
LiteMount Pipe Tubing Extension SP-LTMT-EXT
CableWizard Wall Plate SP-CWWALL
2nd Year Advantage Service Plan (1 year extension)
3rd Year Advantage Service Plan (2 year extension)

Many laptop computers do not automatically turn on their exter- nal video port when a secondary display device such as a projec- tor is connected. Activation commands for some laptop computers are listed in the following table. (If your computer is not listed or the given command does not work, refer to the com- puter’s documentation for the appropriate command.) On some laptops, the activation function key is labeled with an icon, for
commands once activates the
external video port, pressing it
again activates both the external
and internal ports, and pressing it
example or the text CRT/LCD.
a third time activates the internal
port. Refer to your computer’s doc-
umentation for details on your spe-
Key command to activate port
Key command to de-activate port
cific model.
Acer Ctrl-Alt-Esc (for setup) Ctrl-Alt-Esc (for setup)
AST* ** FN-D or Ctrl-D FN-D or Ctrl-D
type from A:/IVGA/CRT type from A:/IVGA/CRT
setup VGA/ Conf.Simulscan
setup VGA/ Conf.Simulscan
F2/Choose Option/F5 F2/Choose Option/F5
Amrel* ** setup menu setup menu
Apple see Mac Portable and Mac PowerBook
BCC* automatic reboot computer
Bondwell LCD or CRT options after bootup
reboot for LCD or CRT options to appear
Chaplet** setup screen setup screen
FN-F4 FN-F4

A p p e n d i x
Key command to activate port
Key command to de-activate port
Compaq* ** Ctrl-Alt-< Ctrl-Alt->
mode/? (for setup option) mode/? (for setup option)
Compuadd* ** automatic automatic
Alt-F for screen setup option
Alt-F for screen setup option
Data General Ctrl-Alt-Command Ctrl-Alt-Command
2 CRT/X at DOS prompt reboot
FN-D FN-D
FN-F12 FN-F12
FN-F2 FN-F2
Dolch dip switch to CRT dip switch to LCD
Epson dip switch to CRT dip switch to LCD
Everex* setup screen option setup screen option
Gateway FN-F1/FN-F1 again simul- taneous
Grid* ** FN-F2, choose auto or simultaneous
Hyundai setup screen option setup screen option
IBM 970* automatic warm reboot

Key command to activate port
Key command to de-activate port
IBM ThinkPad** reboot, enter setup menu FN-F2
FN-F7, select choice from setup menu
PS/2 SC select choice (CRT, LCD, etc.)
Kaypro boot up, monitor plugged in
Kris Tech FN-F8 FN-F8
Mac Portable 100 no video port: not compatible
140, 145, 150, 170 no video port: requires a 3rd-party interface
160, 165, 180, 520, 540, 5300 Control Panel folder, PowerBook Display folder; Activate Video Mirroring
210, 230, 250, 270, 280, 2300 requires Apple Docking Station or Mini Dock
Micro Express* automatic warm reboot
Microslate* automatic warm reboot
Mitsubishi SW2 On-Off-Off-Off SW2 Off-On-On-On
NCR setup screen option setup screen option
NEC* ** setup screen option setup screen option
CRT at the DOS prompt LCD at the DOS prompt
FN-O/* FN-O/*
FN- | | FN- | |

A p p e n d i x
Key command to activate port
Key command to de-activate port
Packard Bell** FN-F2 FN-F2
Samsung* setup screen option setup screen option
Sanyo setup screen option setup screen option
Sharp dip switch to CRT dip switch to LCD
setup screen option setup screen option
setup screen option setup screen option
Top-Link* ** setup screen option setup screen option
Toshiba* ** Ctrl-Alt-End Ctrl-Alt-Home
setup screen option setup screen option
Wyse software driven software driven
FN-F1 FN-F1
* These manufacturers have models that automatically send video to the external CRT port when some type of display device is attached.
** These manufacturers offer more than one key command depend- ing on the computer model.

When you turn video mirroring on (called SimulScan in newer PowerBooks-see below), the projector displays the same informa- tion that appears on your PowerBook’s built-in screen. When video mirroring is off, the projector acts like a separate display.
To turn on video mirroring for the first time:
1 Open the Monitors control panel; click on Monitor 2.
2 Set the number of colors you want.
3 Open the Control Strip; click on the monitor icon.
4 Select “Turn Video Mirroring On.”
Now you can turn video mirroring on and off from the Control Strip without having to open the Monitors control panel again.
When using video mirroring and high color graphics such as slide shows, the projected image occasionally might turn black and white. If this happens, perform the following steps:
1 Turn off video mirroring.
2 Open the Monitors control panel.
3 Move the white menu bar to Monitor 2 to set the projector as the primary monitor.
4 Restart the PowerBook.
Using SimulScan Some newer PowerBooks display images on an external monitor or projector differently than previous ones. When using SimulScan, the projector displays the same information that appears on your PowerBook
To select SimulScan:
1 Open the Control Panel, then double-click Monitors and Sound.
2 In the Resolution list, choose the SimulScan mode, then click OK.
3 If this changes your display settings, a dialog box appears. Click OK to confirm the change.

A p p e n d i x
Use the chart below and the tables on the next page to help you determine projected image sizes.

Projected image size

Distance to Screen (feet)
Height (inches) 4 36 29 22 10 91 73 55 15 137 110 82 20 182 146 109 25 228 182 137 30 274 219 164 35 319 255 191 40 365 292 219
Distance to Screen (feet)
Height (inches) 4 28 22 17 10 71 57 43 15 106 85 64 20 142 114 85 25 177 142 106 30 212 170 127 35 248 198 149 40 283 226 170








Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.