EN
InFocus logo
Official user manual

InFocus IN5504

66 pages·7.6 MB·Projector·PDF·ENDEFRITNLJA
InFocus IN5504
Table of Contents 41 sections Introduction · Positioning the Projector · Ceiling Mount · Cable Management · … ShowHide
Page 1 of the InFocus IN5504 user manual — Regulatory models: F5500, F5530
Page 1 · click to enlarge
Page 1

IN5502, IN5504, IN5532, IN5534 User’s Guide

Regulatory models: F5500, F5530

010-0715-02

Page 2 of the InFocus IN5504 user manual
Page 2 · click to enlarge
Page 2
Declaration of Conformity ManufacturerInFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon 97223-8368 USA

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

We declare under our sole responsibility that this projector conforms to the following directives and norms:

EMC Directive 2004/108/EC EuP Directive 2005/32/EC EMC: EN 55022

Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.

EN 55024 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 2006/95/EC Safety: IEC 60950-1:2005, MOD

This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.

DisplayLink is a trademark of DisplayLink Corporation. Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. Agency Approvals UL, cUL

Other specific Country Approvals may apply. Please see product certification label.

This document applies to regulatory models F5500, F5530.

Input ratings:

For Single Lamp models (F5500) - AC100-240V 5.0-2.0A, 50-60Hz

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For Dual Lamp models (F5530) - AC 100-240V, 9.5-3.5A, 50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

Show 4 more labels / short text on this page
EN 55022 Warning · Trademarks · Canada · FCC Warning
Page 3 of the InFocus IN5504 user manual
Page 3 · click to enlarge
Page 3

Table of Contents Introduction 5 Positioning the projector 7 Ceiling Mount 8 Cable management 8 Connecting power 9 Connecting a computer source 9 Optional computer connections 10 Displaying an image 11 Adjusting the image 12 Connecting a video device 13 Video device connections 13 Shutting down the projector 15 Troubleshooting your setup 15 Using the remote control 23 Using the audio 24 Using the keypad buttons 25 Optimizing computer images 25 Presentation features 25 Optimizing video images 26 Customizing the projector 26 Dynamic Messaging 26 Using the menus 27 Basic Picture menu 28 Advanced Picture menu 29 Setup menu 30 Status and Service menu 33 Help 33 Using Network Functions 34 Using LitePort 38 Maintenance 41 Cleaning the lens 42 Replacing the projection lamp (single lamp) 43 Replacing the projection lamp (dual lamp) 44 Using the security lock 47 Appendix 48 Projected Image Size 48 Optional Lenses 49 SplitScreen Compatibility 53 RS-232 commands 45

Index 64

Page 4 of the InFocus IN5504 user manual
Page 4 · click to enlarge
Page 4

caused by use of non-approved ceiling mount kits or by installing in an improper location.

  • Refer to this guide for proper startup and shutdown procedures.
  • When the projector is ceiling mounted, wear protective eyewear to prevent eye injury before opening lamp door.
  • Follow all warnings and cautions in this manual and on the projector.
  • Do not block the lens with any object while the projector is being used. Blocking the light path can cause overheating and result in fire.
  • The projector must be installed by a qualified professional in order to ensure proper operation and reduce the risk of hazards or injury. It is not recommended you install the projector yourself.
  • Place the projector in a horizontal position no greater than 8 degrees off axis.
  • Refer all service to qualified service personnel. Servicing your own projector can be dangerous to you and will void the warranty.
  • Locate the projector at least 4' (1.2m) away from any heating or cooling vents.
  • Only use replacement parts specified by InFocus. Unauthorized substitutions may result in fire, electrical shock, or injury, and may void the warranty
  • Do not block ventilation openings. Locate the projector in a wellventilated area without obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.
  • Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty.
  • Do not place the projector in direct sunlight, humid, greasy or dusty places or in places where the projector may come into contact with smoke or steam.
  • Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See <a href="http://www.lamprecycle.org" rel="nofollow noopener" target="_blank">www.lamprecycle.org</a> .
  • Do not look directly into the lens while the projector is being used.
  • The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.
  • Do not drop the projector.
  • Do not spill liquid on the projector. Spilled liquid may damage the projector.
  • Use the power cord provided. Connect the power cord to a receptacle with a protective safety (earth) ground terminal. A surge-protected power strip is recommended.
  • In the unlikely event of a lamp rupture, particles may exit through the projector vents. Keep people, food, and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below..
  • Do not overload wall outlets.
  • When disconnecting the power cord, hold the plug, not the cord.
InFocus IN5504 diagram (page 4)
Fig. 1
  • Wash hands after handling the cables supplied with this product.
  • The projector remote control uses batteries. Make sure the batteries’ polarity (+/-) is aligned correctly. Dispose of used batteries in accordance with local disposal laws.
  • Use an InFocus approved ceiling mount kit for proper fitting, ventilation and installation. The warranty does not cover any damage
Page 5 of the InFocus IN5504 user manual
Page 5 · click to enlarge
Page 5

Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty Booklet.

When unpacking your projector, remove the black Lens Protector Ring from around the lens in order to allow full movement of the lens.

KEEP the Lens Protector Ring for future transport purposes. The Lens Protector ring should be re-installed before transporting the projector to prevent damage to the lens shift mechanism.

When preparing the projector for transport, the lens needs to be centered before the Lens Protector Ring can be installed. To do this, access the Lens Shift>Auto Center feature in the Basic Picture menu.

When unpacking your projector, remove the clear Optical Engine Cover from the lens area in order to install the optional lens.

KEEP the clear Optical Engine Cover for future shipping purposes. The optional lens should be removed and the Optical Engine Cover replaced when the projector is being shipped for repair and/or other purposes.

Whenever the optional lens is removed, replace the clear Optical Engine Cover in order to minimize contamination from within the engine compartment.

Page 6 of the InFocus IN5504 user manual — Introduction
Page 6 · click to enlarge
Page 6

Introduction

Optional Accessories Optional accessories include optional top covers in a variety of finishes, optional lenses, the Commander-2 remote, ceiling mount, DisplayLink Extender, DisplayLink Wireless Adapter, and LiteShow II. These items and other accessories can be found on our website at www.infocus.com or at your local dealer.

Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing, too. The IN5502 and IN5532 have WXGA 1280x800 resolution and the IN5504 and IN5534 have native WUXGA 1920x1200 resolution. This guide applies to all four products. They are compatible with a wide variety of computers and video devices. Product Specifications To read the latest specifications on your multimedia projector, be sure to visit our support website at www.infocus.com/support as specifications are subject to change. Online Registration Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives. Included Items

InFocus IN5504 — Introduction diagram (page 6)
Fig. 2 · Introduction

Top rear cover LiteTouch keypad and Remote control receiver

InFocus IN5504 — Introduction diagram (page 6)
Fig. 3 · Introduction

Remote Control · Power Cord · USB cable

Page 7 of the InFocus IN5504 user manual — Introduction
Page 7 · click to enlarge
Page 7

Connector Panel The projector provides both computer and video connection options, including:

power to an InFocus LiteShow II wireless device or InFocus DisplayLink Extender device. 12V Screen Trigger output The 3.5mm mini-jack screen trigger provides a 12 volt, 0.25 amp DC output. It turns on when the lamp is lighted. If you connect your projection screen to this output using the cable that came with your screen, the screen will move down when the lamp is turned on and the screen will return to its storage position, when the lamp is turned off

  • VGA computer (2)
  • HDMI (2)
  • S-video
  • Composite video
  • Component video
InFocus IN5504 — Introduction diagram (page 7)
Fig. 4 · Introduction
  • BNC RGBHV and YPbPr for RGBHV, EDTV and HDTV
  • Separate audio inputs for video and computer
  • USB DisplayLink connector, for computer audio/video input. This USB connection also provides power out for the Wireless DisplayLink Projector Adapter.

The projector also provides the following connectors:

  • Monitor out, to provide an image on your desktop computer as well as on the projection screen.
  • LAN port for network control and web server.
  • LitePort, for connecting a USB flash drive containing JPEG images.
  • Audio out, to provide sound for external speakers.
  • 5 volt DC output
  • 12V screen trigger output
  • Wired remote jack
  • RS-232 connector for serial control. Command control codes are in the Appendix and on our support website at <a href="http://www.infocus.com/support" rel="nofollow noopener" target="_blank">www.infocus.com/support</a> .

5 volt DC output The coaxial 6.4mm x 2.2mm jack provides a constant 5 volt, 2 amp DC output when the projector is on, and will also provide power when the projector is in standby (powered off) if Network and DisplayLink items in the Always-On Functions submenu are set to Yes. It is designed to provide

Page 8 of the InFocus IN5504 user manual — Positioning the Projector
Page 8 · click to enlarge
Page 8

Positioning the Projector

InFocus IN5504 — Positioning the Projector diagram (page 8)
Fig. 5 · Positioning the Projector

To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines:

  • Position the projector on a flat surface at a right angle to the screen. The projector (with the standard lens) must be at least 3 feet (0.9m) from the projection screen.
  • Position the projector within 10 feet (3m) of your power source and within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within 6 inches (.15m) of a wall or other object.
  • Position the projector to the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image.
  • For the standard lens that comes with the projector, the image exits at a given angle. However, the lens shift feature makes the image offset variable.
  • The vertical image offset range for all the projectors is 50% - 110% (default 80%), and the horizontal image offset is +/-10% (default 0%). At 110% offset, 10% of the image height resides above the lens center in tabletop configuration. At 50% offset, 50% of the image height resides above the lens center in tabletop configuration.
Page 9 of the InFocus IN5504 user manual — Ceiling Mount
Page 9 · click to enlarge
Page 9

Ceiling Mount

Cable Management

If you wish to install the projector on the ceiling:

The integrated cable management system allows you to keep the cables organized. To use the cable management system, thread the cables into the slots as shown in the illustration.

  • The projector must be installed by a qualified professional in order to ensure proper operation and reduce the risk of hazards or injury. It is not recommended you install the projector yourself.
InFocus IN5504 — Ceiling Mount diagram (page 9)
Fig. 6 · Ceiling Mount
  • We strongly recommend using InFocus approved ceiling mounts for proper fitting, ventilation and installation. Refer to the installation guide that comes with the InFocus Ceiling Mount Kit (p/n SP-CEILINSTALL) for more information. The warranty does not cover any damage caused by use of non-approved ceiling mount kits or by installing in an improper location.
  • The ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes. Consult your dealer for more information.
  • Maximum supported physical pitch is +/-8º.
  • Maximum supported physical horizontal roll is +/-8º.
  • Keep all adjacent surfaces 3” (76mm) from sides, front and rear and .87” (22mm) from the bottom of projector to preserve required airflow around the projector.

cable management system Using the cable management system provides you with a clean, professional-looking installation.

InFocus IN5504 — Ceiling Mount diagram (page 9)
Fig. 7 · Ceiling Mount
Page 10 of the InFocus IN5504 user manual — Connecting a computer source
Page 10 · click to enlarge
Page 10

Connecting power

RGBHV connection Connect one end of the BNC cable to the computer and the other end of the cable into the BNC connectors on the projector.

Connect the black power cord to the Power connector on the rear of the projector and to your electrical outlet. The Power light on the Status Indicator Panel (page 15) turns amber.

InFocus IN5504 — Connecting power diagram (page 10)
Fig. 8 · Connecting power

Connecting a computer source

DisplayLink If you have a Windows or Macintosh computer, connect the USB cable between your computer's USB port and the projector's DisplayLink connector*. Then to begin installation of the DisplayLink software:

Windows: Follow the instructions on the screen.

Macintosh: A folder will open containing a file named DisplayLink Installer.pkg. Open that file and follow the instructions on the screen.

* For detailed DisplayLink instructions and troubleshooting, and to download the latest DisplayLink software, go to www.infocus.com/support/displaylink

VGA connection Connect one end of the provided computer cable to the VGA 1 or VGA 2 connector on the projector and the other to the VGA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer’s video port first (you can connect this monitor cable to the Monitor Out connector on the projector, see next page).

HDMI 1.3 connection HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video out connector on the video device and into either the HDMI 1 or HDMI 2 connector on the projector.

To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3- compatible source.

Page 11 of the InFocus IN5504 user manual — Optional computer connections
Page 11 · click to enlarge
Page 11

Optional computer connections

InFocus IN5504 — Optional computer connections diagram (page 11)
Fig. 9 · Optional computer connections

To get sound from the projector, connect an audio cable (optional cable, sold separately) to your computer and to the Audio 1 (used with VGA 1) or Audio 2 (used with VGA 2) connector on the projector. You can also assign your source to a different audio in connector, see page 24 and page 31. You may also need an adapter.

If you are using a desktop computer and want to see the image on your computer screen as well as on the projection screen, connect the computer’s monitor cable to the Monitor Out connector on the projector.

To display a presentation using a USB flash drive, see the Using LitePort section on page 38. This feature converts presentations to JPEG images and eliminates the need for a computer source. It can also be integrated with common wall plates and conference room input/output panels.

To advance slides in a PowerPoint presentation using the remote control, plug the USB cable between the projector’s DisplayLink connector and your computer. Then press the up and down arrow buttons on the remote control to move through your slides.

Connect monitor cable · Connect audio cable

Page 12 of the InFocus IN5504 user manual — Displaying an image
Page 12 · click to enlarge
Page 12

Displaying an image

InFocus IN5504 — Displaying an image diagram (page 12)
Fig. 10 · Displaying an image

Touch the Power button on the keypad or the remote.

The Power button blinks green, a beep will sound and the fans start to run. When the lamp turns on, the start up screen will display and the Power button will become solid green. It can take a minute for the image to achieve full brightness.

No start up screen? Get help on page 16.

Turn on computer or video device

InFocus IN5504 — Displaying an image diagram (page 12)
Fig. 11 · Displaying an image

Turn on your computer or video device.

The image should appear on the projection screen. If it doesn’t, press the Source button on the projector’s keypad or remote.

If you are using a VGA cable to connect your computer to the projector (instead of DisplayLink):

If using a laptop, make sure its external video port is active.

Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like Fn + F8 or CRT/LCD key turns the external display on and off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol. Press Fn and the labeled function key simultaneously.

Activate laptop’s external port

Monitor key or LCD/CRT key

InFocus IN5504 — Displaying an image diagram (page 12)
Fig. 12 · Displaying an image

Refer to your laptop’s documentation for more information about your laptop’s key combination or go to the InFocus website at:

http://www.infocus.com/Support/LaptopActivation.aspx

No laptop image? Try pressing the Auto Image button on the keypad or remote. Get help on page 25.

Is your laptop connected to the projector's DisplayLink connector? See the InFocus DisplayLink Software User's Guide (available on the InFocus website at www.infocus.com/displaylink) for troubleshooting information.

Press Power button · Fn key

Page 13 of the InFocus IN5504 user manual — Adjusting the image
Page 13 · click to enlarge
Page 13

Adjusting the image

InFocus IN5504 — Adjusting the image diagram (page 13)
Fig. 13 · Adjusting the image

Position the projector to the desired distance from the screen at a 90 degree angle to the screen. See the Appendix for screen sizes and distances associated with the various lens options.

If the image is square but not centered on the screen or viewing area, adjust Zoom or Focus in the Basic Picture menu. (You can also hold down the Select button for 10 seconds to turn the focus control on.) Then adjust Digital Horz Shift and Digital Vert Shift until the image is centered. See page 28 for help with these menu adjustments.

Adjust zoom, focus and lens shift.

Rotate the elevator feet for granular adjustment of the projector’s height. Avoid placing your hands near the hot exhaust vent at the back of the projector.

Adjust the Contrast or Brightness in the Basic Picture menu. See page 28 for help with these menu adjustments.

Adjust distance · Adjust height · Elevator foot

Page 14 of the InFocus IN5504 user manual — Video device connections
Page 14 · click to enlarge
Page 14

Connecting a video device

HDMI 1.3 connection HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video out connector on the video device and into either the HDMI 1 or HDMI 2 connector on the projector.

You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. You can connect the audio directly to the projector to get sound from the built-in speakers, or you can bypass the projector’s audio system and connect the audio directly from your source to a stereo or home theater system.

To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3- compatible source. S-video connection If your video device uses a round, four-prong S-video connector, plug an S- video cable into the S-video connector on your video device and into the S- video connector on the projector. Use the audio cable as described above.

You can connect the projector to most video devices that can output video. You cannot directly connect the coaxial cable that enters your house from a cable or satellite company; the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner.

Keep in mind that S-video delivers higher quality video output than composite. VGA connection If your video device has a 15-pin VGA output, plug one end of the included computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the computer cable into the VGA 1 or VGA 2 connector on the projector. Component video connection Plug the component cable into the video device. Plug the other end of the component cable into the Component connectors (or if using BNC connectors, plug into the RGBHV or YPbPr connectors as appropriate).

Although the aspect ratio is automatically selected by the projector based on the signal input, you can change the aspect ratio, if desired. The projector’s Aspect Ratio setting is accessed through the Resize button on the remote or through the projector’s Basic Picture Menu. See page 28 for more information.

Video device connections

No video cables are provided with the projector. You can order cables from InFocus or use your own. Composite video connection Plug the composite video cable’s yellow connector into the video out connector on the video device. Plug the other yellow connector into the yellow Composite connector on the projector.

In addition, a Component to VGA adapter can be used in conjunction with the VGA connectors. Plug the component cable into the video device. Plug the other end of the component cable into the adapter and plug the adapter into the VGA 1 or VGA 2 connector.

Plug the white connector of a Mini-plug audio Y-cable into the left audio out connector on the video device and plug the red connector into the right audio out connector on the video device. Plug the other end of the cable into the associated audio in connector on the projector.

Component offers the highest quality analog video output.

Keep in mind that video output from composite connections is not as high quality as S-video.

Page 15 of the InFocus IN5504 user manual — Connecting a video device
Page 15 · click to enlarge
Page 15

What is Aspect Ratio? Aspect ratio is the ratio of the image width to image height. Standard TV screens and older laptops are 4:3; HDTV and most DVDs are 16:9; and widescreen computers are 16:10. If you are projecting onto a screen, the size/shape of the screen will influence the aspect ratio you decide to use. If you are projecting onto a blank wall, there are no screen size restrictions. What you plan to project will also help you choose between 4:3, 16:9 or 16:10. Many TV shows are 4:3, while most movies are 16:9.

4:3 screen 16:9 screen

4:3 mode

If you have a 16:9 screen then you should select an aspect ratio of 16:9 for widescreen movies or HDTV, and Native for 4:3 content. If you have a 4:3 screen you should still use 16:9 for widescreen movies or HDTV, but you also have the option of using either 4:3 (to fill the screen) or Native (for direct pixel mapping) for 4:3 content. Force Wide can also be enabled to automatically resize less common aspect ratios to 16:10.

16:9 mode

Native mode

Page 16 of the InFocus IN5504 user manual — Shutting down the projector
Page 16 · click to enlarge
Page 16

Shutting down the projector

Troubleshooting your setup

Screen Save Time You can make the black screen appear after a preset number of minutes by turning on the Screen Save Time feature in the Setup menu. See page 30. Auto Off Time The projector has an Auto Off Time feature that automatically turns the projector off if no active sources are detected and no user interaction with the projector is performed for 30 minutes. By default, this feature is off. You can change the length of time, see page 30. Turning off the projector To turn the projector off, press the Power button on the remote or keypad. The lamp turns off, a beep sounds and the LED blinks amber for 10 seconds while the fans continue to run to cool the lamp. When the lamp has cooled, the LED lights amber and the fans stop. Unplug the power cable to completely power off the projector.

The Status Indicator Panel on top of the projector indicates the state of the projector and is helpful when troubleshooting.

Table 1Status indicator light behavior and meaning

The projector is plugged in.

The power button has been pressed and the software is initializing.

The projector is on and initialized.

The power button has been pressed to turn the projector off and the fans are running to cool the projector.

Temperature The projector is too hot. Make sure the vents aren’t blocked (see page 21). Turn the projector off and wait one minute, then turn the projector on again. Contact Technical Support if the problem persists. Visit www.infocus.com/support to contact service.

Lamp Turn the projector off and wait one minute, then turn the projector on again. If the lamp light turns on again, replace the lamp and reset the lamp timer (page 43).

Wrench/Service Turn the projector off and wait one minute, then turn the projector on again. If the service lamp turns on again, service is required. Visit www.infocus.com/support to contact service.

Show 5 more labels / short text on this page
Icon Meaning · Power, solid amber · Power, blinking green · Power, solid green · Power, blinking amber
Page 17 of the InFocus IN5504 user manual — Shutting down the projector
Page 17 · click to enlarge
Page 17
InFocus IN5504 — Shutting down the projector diagram (page 17)
Fig. 14 · Shutting down the projector

No start up screen. Plug the power cord into the projector then press the power button.

Only the start up screen appears. If your computer is using the projector's DisplayLink connector, see the DisplayLink Software User's Guide for troubleshooting information.

Press the Source button to activate the laptop’s external port.

Page 18 of the InFocus IN5504 user manual — B
Page 18 · click to enlarge
Page 18

No computer image, just the words “Signal out of range.”

Press the Auto Image button on the keypad or remote. To adjust computer refresh rate, go to Control Panel > Display > Settings > Advanced > Adapter (location varies by operating system).

Computer image projected.

InFocus IN5504 — Shutting down the projector diagram (page 18)
Fig. 15 · Shutting down the projector

Signal out of the range

B

You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped.”

Only my laptop’s background appears, not the Desktop icons.

DisplayLink - Use DisplayLink software to change the display mode from Extended Desktop to Duplicated Desktop. Windows - Disable “Extend my Windows Desktop” in Control Panel > Display > Settings > Display 2 (location varies by operating system).

Background and Desktop projected.

InFocus IN5504 — B diagram (page 18)
Fig. 16

B

B

Uncheck this option, then click Apply

Problem Solution Result

Page 19 of the InFocus IN5504 user manual — Shutting down the projector
Page 19 · click to enlarge
Page 19
InFocus IN5504 — Shutting down the projector diagram (page 19)
Fig. 17 · Shutting down the projector

Set your computer’s display resolution to the native resolution of the projector (Start > Settings > Control Panel > Display > Settings tab).

For a laptop, disable laptop monitor or turn- on dual-display mode

Image not centered on screen. Adjust Lens Shift in the Basic Picture menu

Page 20 of the InFocus IN5504 user manual — Shutting down the projector
Page 20 · click to enlarge
Page 20

Image not square.

Adjust Keystone in the Basic Picture menu. Square image.

InFocus IN5504 — Shutting down the projector diagram (page 20)
Fig. 18 · Shutting down the projector

Image not sharp.

Adjust Sharpness in the Basic Picture menu. Correct image.

InFocus IN5504 — Shutting down the projector diagram (page 20)
Fig. 19 · Shutting down the projector

Image does not fit 4:3 or 16:9 screen.

Change aspect ratio to 4:3 or 16:9 in Basic Picture>Aspect Ratio menu.

Correct image.

InFocus IN5504 — Shutting down the projector diagram (page 20)
Fig. 20 · Shutting down the projector

Problem Solution Result

Page 21 of the InFocus IN5504 user manual — COLOR
Page 21 · click to enlarge
Page 21

Image upside down.

Turn off Ceiling Mount in Setup menu. Correct image.

InFocus IN5504 — Shutting down the projector diagram (page 21)
Fig. 21 · Shutting down the projector

A

Image reversed left to right.

Turn off Rear Project in Setup menu. Correct image.

InFocus IN5504 — A diagram (page 21)
Fig. 22

A

Projected colors don’t match source.

Adjust color, tint, brightness, contrast in the Basic Picture menu and/or color space in the Advanced Picture menu.

Correct image.

InFocus IN5504 — A diagram (page 21)
Fig. 23

COLOR

COLOR

Problem Solution Result

Page 22 of the InFocus IN5504 user manual — Shutting down the projector
Page 22 · click to enlarge
Page 22
InFocus IN5504 — Shutting down the projector diagram (page 22)
Fig. 24 · Shutting down the projector

The video embedded in my PowerPoint presentation does not play on the screen

If your computer is using the projector's DisplayLink connector, see the DisplayLink Software User's Guide for video troubleshooting information. Turn off the internal LCD display on your laptop.

Lamp won’t turn on, Temperature light is on. Make sure vents aren’t blocked, turn the projector off and allow it to cool for one minute.

Page 23 of the InFocus IN5504 user manual — Shutting down the projector
Page 23 · click to enlarge
Page 23
InFocus IN5504 — Shutting down the projector diagram (page 23)
Fig. 25 · Shutting down the projector

“Replace lamp” message appears at startup, lamp won’t turn on, Lamp light is turned on.

If you need assistance, visit our support website at www.infocus.com/support or call us. Check out the How To section for additional information on using this projector for home theater or gaming applications.

This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full value.

Page 24 of the InFocus IN5504 user manual — Using the remote control
Page 24 · click to enlarge
Page 24

Using the remote control

  • Mute button to silence the audio.
  • Auto Image button to resynchronize the projector to the source.

The remote uses two (2) AA batteries. You can install the batteries by removing the cover from the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.

  • Resize button to switch among aspect ratios (see page 28).

Wired Remote Option If the wireless range of the standard remote is not sufficient, an optional Commander remote can be wired directly into the projector’s Wired Remote connector.

  • When disposing of the batteries, be sure to do so in an environmentally proper manner.
  • If the remote control gets wet, wipe it dry immediately.
  • Avoid excessive heat and humidity.
  • Make sure the batteries are installed in the proper orientation and are not dead.
  • Ensure the batteries’ polarity (+/-) is aligned correctly.
  • Do not mix new and old batteries together, or different types of batteries together.
  • Make sure you’re pointing the remote at the projector or the screen, not the computer, and are within the remote range of 30’ (9m). For best results, point the remote at the projector.
  • Replace the batteries as soon as they run out.
InFocus IN5504 — Using the remote control diagram (page 24)
Fig. 26 · Using the remote control
  • Remove batteries from the remote control when storing or not in use for a prolonged period.

To operate, point the remote at the projector (not at the computer). The range of optimum operation is about 30’ (9m).

Press the remote’s Power button to turn the projector on and off (see page 15 for shutdown information).

Press the remote’s Menu button to open the projector’s menu system. Use the arrow buttons to navigate, and the Select button to select features and adjust values in the menus. See page 27 for more information on the menus.

The remote also has:

  • Source button to switch between sources.
  • Volume buttons to adjust the sound.
  • Custom button that can be assigned to a special function, like Blank Screen or Freeze (see page 30).
  • Help button to access the projector’s help feature (see page 33).
  • Blank button to blank the screen.
  • Presets button to select stored settings (see page 28).

Troubleshooting the remote

Page 25 of the InFocus IN5504 user manual — Using the audio
Page 25 · click to enlarge
Page 25

Using the audio

system and connect the audio directly from your source to a stereo or home theater system.

Using the projector’s speakers When the computer is using the DisplayLink or HDMI connectors, both audio and video are sent over the respective cable to the projector and audio will play from the projector's speakers.

InFocus IN5504 — Using the audio diagram (page 25)
Fig. 27 · Using the audio

For inputs other than DisplayLink and HDMI, connect the audio source to the associated audio connectors in order to use the projector's speakers.

To adjust the volume, press the Volume buttons on the keypad or remote.

Troubleshooting Audio If you aren’t hearing the audio, check the following:

  • If your computer is using the projector's DisplayLink connector, see the InFocus DisplayLink Software User's Guide on the website at <a href="http://www.infocus.com/displaylink" rel="nofollow noopener" target="_blank">www.infocus.com/displaylink</a> for audio troubleshooting information.
  • Make sure the audio cable is connected to the correct audio in connector, Computer or Video.
  • Make sure the volume is turned up enough. Press the Volume button on the keypad or remote.
  • Make sure you are connected to the corresponding audio in for your source. By default, Audio 1 corresponds to VGA 1 , Audio 2 corresponds to VGA 2 and RGBHV/YPbPr , Audio 3 corresponds to Component , Audio 4 corresponds to S-video , and Audio 5 corresponds to Composite . You can change these assignments, see page 31 .
  • Make sure that you are connected to an audio out connector on the source as opposed to a line in or microphone connector.
  • Adjust the audio source.
  • If playing a video, make sure the playback has not been paused. Connecting external speakers The projector can be attached to external amplified speakers by connecting a 3.5mm stereo audio cable from the Audio Out connector on the projector to the amplified speakers. Alternatively, you can bypass the projector’s audio

Adjust volume

Page 26 of the InFocus IN5504 user manual — Presentation features
Page 26 · click to enlarge
Page 26

Using the keypad buttons

Optimizing computer images

After the projector is running and the image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 27.

Most buttons are described in detail in other sections, but here is an overview of their functions:

Power–turns the projector on and off (page 9).

  • Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu (page 28).

Auto Image–resynchronize the projector to the source (page 30).

Presets–cycles through the available preset settings (page 28).

  • Change the Aspect Ratio. Choose the option that best fits your input source (page 28).

Menu–opens the onscreen menus (page 27).

  • Adjust the Color Temperature in the Advanced Picture menu (page 29).

Select–confirms choices made in the menus (page 27).

Up/Down/Left/Right arrows–navigates to and adjusts settings in the menus (page 27).

  • Adjust the Phase, Tracking, or Horizontal or Vertical position in the Advanced Picture menu (page 29).
  • Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these settings later (page 28).

Source–changes the active source (page 9).

Help–button to access the projector’s help feature (page 33)

InFocus IN5504 — Using the keypad buttons diagram (page 26)
Fig. 28 · Using the keypad buttons
  • If your computer is using the projector's DisplayLink connector, see the InFocus DisplayLink Software User's Guide for information about optimizing images.

Presentation features

Several features are provided to make giving presentations easier. Here is an overview, details are found in the menu section.

  • The Custom key allows you to assign various features to the button. The default effect is Source Info, which displays information about the projector and current source. See page 30 for details.
  • The Search Screen option lets you change the appearance of the blank screen and start up screen (page 31).
  • Two options, Auto Off and Screen Save Time, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life (page 30).
Page 27 of the InFocus IN5504 user manual — Customizing the projector
Page 27 · click to enlarge
Page 27

Optimizing video images

Dynamic Messaging

After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 27.

Using command codes, text messages can be sent for display by the projector (and all other InFocus projectors with the Dynamic Messaging feature) over a network or serial connection. Text is shown on top of whatever else is being displayed, and can be shown in ticker tape format or in a box, with optional beep tone alert. This is a great way to display urgent alert messages to employees, and simply requires a connection to the projector’s RS-232 serial control or LAN connector. Command codes for executing Dynamic Messaging are in the Appendix and available on our website at www.infocus.com/support

  • Adjust the Keystone, Contrast, Brightness, Color, Tint or Sharpness in the Basic Picture menu (page 28).
  • Change the Aspect Ratio. Choose the option that best fits your input source (page 28).
  • Adjust the Color Temperature. Select a listed warmth value (page 29).
  • Turn on Overscan to remove noise on the edges of the image (page 29).

Customizing the projector

You can customize the projector for your specific setup and needs. See page 30 to page 31 for details on these features.

  • For rear projection, turn Rear Project on in the Setup menu.
  • For ceiling mounted projection, turn Ceiling Mount on in the Setup menu.
  • Specify which source the projector checks first for active video during power-up.
  • Specify the function of the Custom key on the remote.
  • Turn the projector’s display messages on and off.
  • Turn on power saving features.
  • Specify appearance of blank screen and startup screen.
  • Specify the language viewed on the menus.
Page 28 of the InFocus IN5504 user manual — Using the menus
Page 28 · click to enlarge
Page 28

Using the menus

To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) Use the arrow buttons to move up and down to highlight the desired menu, then press the Select button.

InFocus IN5504 — Using the menus diagram (page 28)
Fig. 29 · Using the menus

To change a menu setting, highlight it, press Select, then use the arrow buttons to adjust the value or select an option or turn the feature on or off. Press Select to confirm your changes. Use the arrow buttons to navigate to another setting. When your adjustments are complete, press Menu to access a different menu; press the Menu button at any time to navigate to the higher-level menu and ultimately close the menus.

Basic Picture menu Advanced Picture menu

The menus are grouped by usage:

  • The Basic Picture menu provides common image adjustments.
  • The Advanced Picture menu provides more complex image adjustments.
InFocus IN5504 — Using the menus diagram (page 28)
Fig. 30 · Using the menus
InFocus IN5504 — Using the menus diagram (page 28)
Fig. 31 · Using the menus
  • The Setup menu provides set-up type adjustments that are not changed often.
  • The Status and Service menu provides information about the projector and source.

Setup menu Status and Service menu

InFocus IN5504 — Using the menus diagram (page 28)
Fig. 32 · Using the menus
Page 29 of the InFocus IN5504 user manual — Basic Picture menu
Page 29 · click to enlarge
Page 29

Basic Picture menu

Horz Keystone/Vert Keystone: Adjusts the image horizontally or vertically and makes a squarer image.

To adjust the following settings, highlight the setting, press Select, use the arrow buttons to adjust the values, then press Select to confirm the changes.

Focus and Zoom: Adjusts the focus and zooms the image in or out.

Digital Zoom: Changes the size of projector’s display area. If the display area has been resized by this setting, it can be moved by changing the Horz Shift and Vert Shift settings.

Brightness: Changes the intensity of the image.

Contrast: Controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image.

Lens Shift...: Shifts the lens to the up and down or left and right. To center the lens for transport or other purposes, activate the ‘Auto Center’ feature. This process will take a minute or two to complete.

Sharpness: Changes the clarity of the edges of a video image. Select a sharpness setting.

Digital Horz Shift/Vert Shift: Moves the display area horizontally or vertically if its size has been changed by the Digital Zoom setting.

Color: Adjusts a video image from black and white to fully saturated color. The color setting applies to video sources only.

Tint: Adjusts the red-green color balance in the image of NTSC video images. The tint setting applies to NTSC video sources only.

SplitScreen: Allows two distinct sources to be displayed simultaneously. Switch primary sources, make picture adjustments and choose one of multiple display options: either two side by side horizontal or vertical source regions, or a small secondary source image displayed on top of the primary source in one of four placement options. See page 53 for display options.

Auto Image: Forces the projector to reacquire and lock to the input signal. This is useful when signal quality is marginal.

Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9.

Select Auto to have the projector choose the ratio. Choose Native to see the unmodified input with no resizing by the projector. Select 16:9 to watch enhanced widescreen DVDs.

For more information regarding Aspect Ratio, see page 14.

Apply Preset...: Presets are provided that optimize the projector for displaying computer presentations and video images under certain conditions.

There is also a user-definable preset. To set this preset, adjust the image and select Save User in the Presets menu. You can recall these settings in the future by selecting the User preset.

Increasing keystone Decreasing keystone

Basic Picture menu · Aspect ratio

Page 30 of the InFocus IN5504 user manual — Advanced Picture menu
Page 30 · click to enlarge
Page 30

Advanced Picture menu

Detect Film: Controls film mode detection, and determines whether the original source of the input video was film or video.

BrilliantColor™: Produces an expanded onscreen color spectrum that delivers enhanced color saturation for bright, true-to-life images. Choose Normal Look for most video sources and Bright Look for most computer sources.

Gamma: Select the appropriate gamma from among Video, Film, Bright, and CRT.

Color Gain Settings: Adjusts the gain of the red, green, or blue channel of the image.

White Peaking: (video sources only) Increases the brightness of whites that are near 100%.

Color Offset Settings: Adjusts the offset of the red, green, or blue channel of the image.

DynamicBlack™: (IN5502, IN5504 only) Select Auto to constantly adjust the aperture based on the amount of black in the current scene, or select a percentage for a fixed aperture size (100% is maximum size).

Horizontal/Vertical Position: Adjusts the position of a computer source.

Horizontal/Vertical Pincushion: Corrects optical pincushion distortion.

Color Temperature: Changes the intensity of the colors. Select a listed relative warmth value.

InFocus IN5504 — Advanced Picture menu diagram (page 30)
Fig. 33 · Advanced Picture menu

Force Wide: When this is off, the analog locking algorithms choose the standard mode resolution (4:3) as the preferred default resolution. When this is on, the analog locking algorithms choose wide mode resolution (16:10) as the preferred default resolution.

Overscan: Removes noise around the video image.

Phase: Adjusts the horizontal phase of a computer source.

Sync Threshold: (progressive signals only) If a hardware device, such as a DVD player, is not syncing properly with the projector, select this option to help it to sync when connected to the projector.

Tracking: Adjusts the vertical scan of a computer source.

Color Space: This option applies to computer and component video sources. It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources or choose either REC709 or REC601 for component video sources.

Noise Reduction: Reduces temporal and/or spatial noise in the image.

Flesh Tone Correction: Controls the amount of flesh tone correction applied to the image.

Set Black Level...: Analyzes the current input image and calculates an offset value which is then added to the analog to digital converter black level value. This ensures optimum black level for each analog source.

Advanced Picture menu

Page 31 of the InFocus IN5504 user manual — Setup menu
Page 31 · click to enlarge
Page 31

Setup menu

  • Projector Info : Shows the Projector Info menu.
  • Overscan : Removes noise around the image.

Language: Allows you to select a language for the onscreen display.

Network: Allows you to setup network settings. See page 34 for details on network configuration and operation.

  • AV Mute: Enables or disables AV Mute function.
  • Closed Captions: Enables or disables Closed Captions.
  • SplitScreen: Enables or disables SplitScreen. Before using this for the first time, configure SplitScreen sources and layouts using the SplitScreen menu (page 28).
  • DHCP: Turns the DHCP on or off.
  • IP Address: Assign Network IP Address.
  • Subnet Mask: Assign Network Subnet Mask.

Blank Key: Select what to display when the blank key on the remote is pressed: your custom snapshot, a solid color screen (blue, black or white), the factory logo screen, a timer, or test patterns. The timer option is useful for classroom tests or break times during meetings.

  • Default Gateway: Assign Network Default Gateway.
  • WINS Host Name Lookup: Turns WINS Host Name Lookup on or off.
  • Host Name: Displays the host name.
  • MAC Address: Displays network MAC Address value.

Source Keys: Enables or disables Source Keys on the optional Commander-2 remote.

  • Show Network Messages: Turns network messages on or off. Network messages display the projector’s IP address (and host name if enabled) when the projector is also displaying source messages.

AC Power On: When this feature is on, the projector automatically turns on when electrical power is connected. This allows control of ceiling mounted projectors with a wall power switch.

  • Restart Network…: Restarts the network.
  • Network Factory Reset…: Performs factory reset.

Auto Off Time: Automatically turns the projector off after no signals are detected for a preset number of minutes. If an active signal is received before the projector powers down, the image will be displayed.

Key Click: Turns the key click sound on or off. When this setting is on, pressing keys on the keypad causes the projector’s speaker to play a “click” sound.

Screen Save Time: Automatically blanks the screen with a black color after no signals are detected for a preset number of minutes. The image returns when an active source is detected or a remote or keypad button is pressed.

Custom Key: Allows you to assign a different function to the Custom button, allowing you to quickly and easily use the effect. Highlight an effect and press Select to choose a different one.

Sleep Timer: Allows the projector to automatically power off after it has been on for a specified amount of time.

  • Blank Screen : Displays an empty screen.
  • Mute : Turns off all sound.

Always-On Functions: Allows you to control which projector functions will work even when the projector is in standby (powered off but connected to AC Power). Press Up or Down to highlight the function you want to change, then press select or left and right to change the function to either Yes or No. Press menu when done. Note that some functions must always have the same value; in this case when you change one value, other values in the submenu may also change automatically.

  • Aspect Ratio : Sets the ratio of image width to image height (see page 14 and page 28).
  • Source : Cycles through available sources.
  • Auto Image : Resynchronizes the projector to the source (page 25).
  • Freeze Screen : Pauses the projected image.
  • Source Info : The default action. Shows the Source Info menu.
Page 32 of the InFocus IN5504 user manual — Setup menu
Page 32 · click to enlarge
Page 32

Lamp Low Power: Toggles between on and off. Turn it on to lower the light output of the lamp. This also lowers the fan speed, making the projector quieter.

Auto Keystone: Automatically adjusts vertical keystoning.

Prevent PC Screen Saver: Prevents your computer from going into Screen Save mode. The projector must be connected to the PC via a USB cable for this feature to work.

Current Lamp: (IN5532/IN5534 only) Controls which lamp(s) is in use.

Lamp Auto Switch: (IN5532/IN5534 only) Controls when the projector switches between lamps. Choices include: upon failure, at power-up, or after a set number of hours.

Search Screen: Allows you to display one of the following options instead of the default screen at startup, and when no source is detected. Options include the factory logo screen, a custom Snapshot, or a blue, black or white screen.

Power Sounds: Controls whether the projector makes a sound when powered on and off.

Take Snapshot...: Captures the current image and allows it to be used as the search screen image.

Internal Speakers: Allows the user to turn on and off the internal speakers.

Disable Snapshot: Allows the user to disable the snapshot capability.

Audio Inputs: Assign an audio input to a specific video/computer source input. (Default settings are as follows: Audio 1 is used with VGA 1; Audio 2 is used with VGA 2 and RGBHV/YPbPr; Audio 3 is used with Component; Audio 4 is used with S-video; Audio 5 is used with composite.)

Show Messages: Displays status messages (such as “Searching”) in the lower- left corner of the screen.

Menu Offset: Allows you to change the position of the On Screen Display items.

Press up or down to highlight the source you want to change, then press select or the left and right arrow keys to change that source’s audio input. Press menu when done changing audio inputs.

Menu Transparency: Allows you to change how much of the projected image behind the menu you can see. As the value increases, more of the image behind the menu is visible.

Auto Source: When this feature is On, the projector automatically finds the active source, checking the selected Power-up Source first. When this feature is Off, the projector defaults to the source selected in Power-up Source. To display another source, you must manually select one by pressing the Source button on the remote or keypad.

Magnify Controls: Allows you to change the function of the arrow buttons when the menu is not shown. By default, the arrow buttons allow you to advance slides while in PowerPoint’s SlideShow mode. To make the arrow buttons also adjust magnify settings, choose Magnify Controls to turn magnify controls on. Now when the menu is not shown, you can press the Select button to switch between the magnification settings (Magnify Level, Magnify Horizontal Position and Magnify Vertical Position), then press Select again to turn off magnify controls and use the arrow buttons to advance slides.

Power-up Source: Determines which source the projector checks first for active video during power-up.

Fast Color Refresh: Controls color wheel speed.

Closed Captions: Controls closed caption display while audio is not muted. If this setting is not off, and audio is not muted, and the source is NTSC and contains captions on the selected channel, then the projector must display caption text overlaid on the image.

Lens Adjust Enable: When turned on, lens shift, zoom, focus, digital keystone, auto keystone and pincushion adjustments can be made. When the product has been mounted, installers can turn this feature off to prevent changes to lens shift, zoom, focus, keystone and pincushion settings.

Ceiling Mount: Turns the image upside down for ceiling-mounted projection.

Rear Project: Reverses the image so you can project from behind a translucent screen.

Keypad Enable: Enables or disables keypad.

Page 33 of the InFocus IN5504 user manual — Setup menu
Page 33 · click to enlarge
Page 33

Glow Ring: Controls the brightness level of the glow ring status indicator.

PIN Protect: The PIN (personal identification number) feature allows you to password protect your projector. Once you enable the PIN feature, you must enter the PIN before you can project an image. The default PIN on this projector is Menu-Up-Down-Select-Source. Use the navigation buttons on the remote or keypad to enter the correct 5-button press sequence. When all 5 numbers are entered correctly, press the Select button on the remote or keypad to select OK. If the message “Wrong PIN” appears, verify the code and re-enter it. If you mis-enter a number, you must enter 5 numbers and press the Select button in order to access the “Wrong PIN” message and re- enter the code.

To enter the PIN at projector startup:

Power up the projector. The “Enter PIN” dialog box appears after the startup screen. Enter the PIN. Use the navigation buttons on the remote or keypad to enter the correct button press sequence. See the description above for instructions.

To change the PIN:

Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the new PIN. You can navigate between OK and Cancel by pressing the arrow buttons on the keypad. Select OK or Cancel by pressing the Select button. Verify the new PIN.

If you lose or forget your custom PIN:

Contact InFocus support at www.infocus.com/support

Serial Port, Baud Rate: Selects the serial port and baud rate.

Serial Port Echo: Controls whether the serial port echoes characters.

Setup menu

Page 34 of the InFocus IN5504 user manual — Status and Service menu
Page 34 · click to enlarge
Page 34

Status and Service menu

Help

Source Info: Displays current source settings (read-only).

Press Help (on the keypad or remote) at any time to get interactive help for solving common, picture, sound, and cabling problems.

Projector Info: Displays current projector settings (read-only).

Reset Lamp Hours: Resets the lamp hours used counter in the Projector Info menu to zero. Do this only after changing the lamp.

InFocus IN5504 — Status and Service menu diagram (page 34)
Fig. 34 · Status and Service menu

Factory Reset: Restores all settings to their default.

Service Code: Only used by authorized service personnel.

InFocus IN5504 — Status and Service menu diagram (page 34)
Fig. 35 · Status and Service menu

Status and Service menu

To revert a customized Help screen back to the InFocus default Help screen, a Factory Reset will be needed.

Page 35 of the InFocus IN5504 user manual — NOTES:
Page 35 · click to enlarge
Page 35

Using Network Functions

3 Select IP Address. This will highlight the first of the four octets in the IP address. Press Up or Down to change the value, then press Select or Right when done to move to the next octet. Repeat until you have changed all four octets in the IP address. 4 Repeat the above for Subnet Mask, Default Gateway, and other settings that are in IP address format (to assign or change the Host Name, see Network Settings Page below).

Projector network functions include:

  • Configuring and controlling the projector via a web browser.
  • Failure and warning alerts via email.
  • Projector Management via SNMP.
  • Controlling the projector via Scheduling.

Configuring and Controlling the Projector via a Web Browser You can adjust or control the projector via a network from a web browser on a computer that is connected to the same network as the projector.

For network control, you can access the projector through Port 23 (Telnet). We use the same control codes on serial as we do over the network. InFocus network control uses the Telnet packet structure.

NOTES:

  • To access the projector’s web pages, the projector must be connected to the network and connected to AC power (and if you want to access the web pages even when the projector is powered off, make sure that the Network item in the Always-On Functions submenu is set to Yes).

Before using the network functions To use the network functions of the projector, the projector must be configured to suit your network. Consult with your network administrator before connecting the projector to your network; incorrect network configuration of the projector may cause problems on your network.

  • JavaScript must be enabled in your browser to use the projector web pages properly. If JavaScript is disabled, see the Help files for your web browser for details on how to enable it.

Connect the Network Cable Properly connect projector to the network, then configure the following settings.

  • If no operations are performed in the web browser for approximately ten minutes, the system will automatically log you off. Logging in To log into the projector web pages, follow these steps:

If Using a Network with DHCP Enabled:

1 Use the projector's remote control or keypad to select the Network item in the projector's Setup menu.

1 Make sure the projector is connected to the network and connected to AC power.

2 If DHCP is off, select it to turn it on.

2 If you don't know the projector's IP address, turn on the projector. After the projector starts up, if its IP address is not shown, press the Source button to view the IP address.

If Using a Network that does not have DHCP Enabled:

1 Use the projector's remote control or keypad to select the Network item in the projector's Setup menu. 2 If DHCP is on, select it to turn it off

Page 36 of the InFocus IN5504 user manual — Using Network Functions
Page 36 · click to enlarge
Page 36

3 Start a web browser on your computer.

  • To change an on/off setting (e.g. Power): Click the corresponding On or Off button.

4 Enter the projector's IP address or host name (preceded by http://) into the web browser's address bar. Example: If the IP address is 192.168.1.10, enter http://192.168.1.10 into the browser's address bar.

  • To change a multi-value setting (e.g. Sharpness): Select a value from the drop-down menu.
  • To change a numeric setting (e.g. Brightness): Click the corresponding + or - button, or select a value from the drop-down menu.

5 The Log In to Projector Control page will be shown in the browser.

  • To perform a command (e.g. Auto Image): Click the corresponding Execute button. Network Settings Page (administrators only) This page lets you view and change the projector's network settings. Consult with your network administrator before making any changes on this page; incorrect network configuration of the projector may cause problems on your network.

6 Select Access type: Basic User or Administrator.

7 Click Log In.

Navigating Projector Web Pages The left side of every page shows a navigation bar. Click the links in the navigation bar to go to different projector web pages.

Projector Name: The name of the projector shown in the projector's web pages.

The top of the navigation bar shows the projector name, model, and serial number.

IP Address: These settings control the projector's network configuration. Enter the appropriate settings required for your specific network.

The web pages also include the following options:

  • Log Off: Logs off and returns to the Log In page (see above).
Advanced Network SettingsClick this link to show advanced settings:
  • Refresh: Reloads the page with current status.

802.1x Authentication: If your network requires 802.1x authentication, enter the user name and password that the projector should use, and select the authentication type.

  • Defaults: Displays default (factory settings) values (to save these values click Apply).
  • Apply: Saves the values that are currently shown on the page. Projector Controls Page (All users) This page lets you control the same settings that are available via the projector's main menu and remote control. The Controls tab includes basic remote control functions; other tabs correspond to the projector's menus.

SNMP: If your network uses SNMP, enter necessary SNMP information here.

Command and Control Pass-Through: This setting allows you to send and receive projector commands over the network. For command codes, see the Appendix or visit the InFocus website at: www.infocus.com/support

In each tab, the current value of each setting is shown in blue color.

Page 37 of the InFocus IN5504 user manual — Using Network Functions
Page 37 · click to enlarge
Page 37

Event Notifications Page (administrators only) This page lets you configure the projector to automatically send email when specific events occur.

Start: Select when daylight savings starts.

End: Select when daylight savings ends.

Automatically adjust…: Check this to have the projector automatically update time and date when daylight savings starts and ends.

E-Mail Settings tab: In the Account Used… section, enter the information needed for your projector to connect to an email sending (SMTP) server. Then in the Recipient E-Mail Addresses section, enter the email addresses of people who will receive emails, and for each address, select whether that address receives reminders and/or warnings and errors (enter only one address per line). After you have completed this page, click Send Test to make sure that email is correctly set up.

Scheduled Tasks Page (administrators only) This page lets you configure the projector to perform tasks automatically on specific days and times. You can set up a maximum of three different scheduled tasks; each tab corresponds to a task. Each scheduled task can perform different commands on different days and times. Each tab contains the following items:

Reminders tab: Select which types of reminders to send. For most reminders, you can adjust the frequency or date/duration associated with the reminder.

On/Off: Select whether or not this scheduled task will run on the days and times shown.

Description: Explanation of what the task does.

Date/Time Settings Page (administrators only) This page lets you configure the projector to read the time and date from an SNTP server on your network. NOTE: The projector does not have a built-in clock. If the projector is unable to access the SNTP server, or no SNTP server is defined, functions that rely on the time and date may not work correctly.

Run Every: Select the days of the week when the scheduled task should run.

At Time(s): Select the times of day when the scheduled task should run (the task will run at the indicated times on every one of the days checked above).

Command Sequence and Available Commands: The Command Sequence list on the left shows commands currently performed by the scheduled task (each task can include up to 20 commands). The Available Commands list on the right shows all commands that can be added to a scheduled task.

Current Date and Time: Shows the current date and time read from the SNTP server.

Synchronize the system clock…: Select how often the projector should check the SNTP server to get the time and date. Between checks, the projector will keep track of the amount of time elapsed, allowing it to maintain the correct time and date.

>> Remove: Removes the command selected in the Command Sequence list.

Move Up: Moves up the command selected in the Command Sequence list.

SNTP Server: The address of the time and date server on your network.

Move Down: Moves down the command selected in the Command Sequence box list.

Time Zone: The projector's time zone (if you are in a different time zone from the projector, make sure this is the time zone of the region where the projector is located).

Clear All: Erases all commands in the Command Sequence list.

Set Now: Click this to immediately set the time and date based on the above information.

Custom: Click this link to show custom command entry options. With custom commands, you can perform additional commands not shown in the Available Commands list. The RS-232 command codes are available in the Appendix and on our website at www.infocus.com/support NOTE:

Daylight Savings SettingsClick this link to show daylight savings settings:
Page 38 of the InFocus IN5504 user manual — Using Network Functions
Page 38 · click to enlarge
Page 38

Custom commands you enter here should be in write format (do not include '?'), and should use '' instead of '(' and ')'. Example: to turn on the ceiling mount setting, use the custom command .

Network Subsystem Factory Reset: Returns all network and LitePort settings to default values and then restarts the projector network subsystem.

Troubleshooting Network Functions • If network status is shown as Not Connected in the projector's Network menu, or the projector does not display its IP address, check the cable or the network configuration.

User Access and Security Page (administrators only) This page lets you configure security options for the projector, including log in passwords and projector access restrictions.

Web Access - Administrator tab: Select whether or not Administrators must enter a password to log into the projector's web pages. If a password is required, click create or change password to update the administrator password.

  • If your web browser displays Page Not Found or a similar error when you try to access the projector's web pages, verify that the projector is connected to the network (select the Network item in the projector's Setup menu and verify that Network Status shows as Connected); if there is no connection refer to the troubleshooting item above for more help.

Web Access - Basic User tab: Select whether or not Basic Users must enter a password to log into the projector's web pages. If a password is required, click create or change password to update the basic user password.

  • Make sure the Network item in the Always-On Functions submenu in the Setup menu is set to Yes (if it is set to No, the projector web pages will only be available when the projector is powered on).

Projector PIN tab: Allows you to turn projector PIN protection on or off, or change the PIN. When PIN protection is on, the current PIN must be entered when the projector is powered on, otherwise the projector will not operate. NOTE: PIN protection only applies to projector operation via the projector's keypad and remote control; it does not affect the projector's web pages.

  • If scheduled tasks are not performed, check if the SNTP is set up correctly and is online. Also check if the Command sequence is correct.
  • If automatic emails are not sent, check if SMTP is set up correctly and is online.

System Log Page (administrators only) This page shows a log of the 100 most recent projector events.

To manually restart the projector network subsystem: Use the projector's remote control or keypad to select the Network item in the projector's Setup menu. Then scroll down and select either Restart Network (to restart the network subsystem without changing any settings), or Network Factory Reset (to return all network settings back to default values, and then restart the network subsystem). If the manual restart procedure does not work: To force the network subsystem to restart, disconnect the projector from AC power, wait 10 seconds, then reconnect AC power.

Erase Log…: Click this to erase all events in the log.

Network Utilities Page (administrators only) This page lets you perform various network-related projector tasks.

Save and Load Projector Configuration: These functions save and load all network-related projector settings into/from a file stored on your computer. This lets you quickly 'clone' network settings from one projector to other projectors.

Upgrade Projector Network Firmware: Upgrades the firmware for the projector's network and LitePort features (this firmware is separate from the regular projector firmware).

Restart Projector Network Subsystem: Restarts the projector network subsystem; does not change any projector settings.

Page 39 of the InFocus IN5504 user manual — Using LitePort
Page 39 · click to enlarge
Page 39

Using LitePort

highlighted to start the slide show, or press Select when a folder is highlighted to open that folder.

LitePort displays a slide show of JPEG images stored on a USB flash drive connected to the projector. This can eliminate the need for a computer source.

To start the slide show: While viewing thumbnails, press the arrow buttons to highlight a thumbnail, then press the Select button to start the slide show at the highlighted image.

Image File Types LitePort displays image files in JPEG format only (file extensions .JPEG and .JPG). Other file types including PDF, BMP, TIFF, PNG, GIF, etc. are ignored.

To change the image during the slide show: Press the Down or Right button to go to the next image, or press the Up or Left arrow button to go to the previous image (the slide show may also advance automatically depending on the value of the Next Slide setting; see the LitePort Menu section below for details).

Viewing a Slide Show To view your pictures as a slide show, follow these steps:

To change to a different folder: While viewing thumbnails, press the arrow buttons to highlight the desired folder icon, then press the Select button (to go to the higher-level folder, select the folder icon labeled "Up").

1 Connect a USB flash drive to your computer and copy JPEG files from your computer to the USB flash drive.

To change LitePort settings: Press the Menu button during the slide show, or while viewing thumbnails (see the LitePort Menu section below for details).

2 Turn on your projector if needed.

3 Remove the USB flash drive from your computer and plug it into the LitePort connector on the rear of the projector.

Using the LitePort Menu To show the LitePort menu, press the Menu button on the keypad or remote during the slide show, or while viewing thumbnails. To highlight a menu item, press arrow buttons. Then to do the action or change the setting, press Select. To remove the menu, press the Menu button again.

4 The projector will start a slide show of the images found (if you see image thumbnails instead, see To Start the Slide Show section below).

5 To go to the next image in the slide show, press the Down or Right arrow button on the projector keypad or remote. To go to the previous image, press the Up or Left arrow button.

Rotate Picture: Rotates the current image by 90 degrees clockwise (rotation is temporary; the image returns to its original orientation when the USB flash drive is removed from the projector or when the projector is turned off).

Controlling LitePort When you plug a USB flash drive into the projector's LitePort connector, the projector will scan the drive and then either start a slide show or show image thumbnails.

Stop/Start Slideshow: Stops the slide show, or starts it at the selected thumbnail (when the menu is not visible, you can also stop or start the slide show by pressing the Select button).

Go to Projector Main Menu: Removes the LitePort menu and displays the projector's main menu, where you can adjust the picture or change other projector settings.

To stop the slide show and view thumbnails: Press the Select button during the slide show. In Thumbnails view, the name of the current folder, the current image number, and the total number of images in that folder are shown at the bottom of the screen. While viewing thumbnails, press the arrow buttons to scroll through the thumbnails, or press Select when an image is

Page 40 of the InFocus IN5504 user manual — Using LitePort
Page 40 · click to enlarge
Page 40

(For remaining items below, highlight the setting, then press Select one or more times to change the setting value.)

4 Click the Office button in the upper left corner of the PowerPoint docu ment window.

Auto Start: Select On to have the player start the slide show when the USB flash drive is first connected. Select Off to have the player display thumbnails when the USB flash drive is first connected.

5 Point to Save As, then click Other Formats.

6 In the Save As dialog box, click the Save as type drop-down menu. Scroll through the menu and select JPEG File Interchange Format.

Show All Folders: Select On to have the slide show display all images in all folders. Select Off to have the slide show display images only from the current folder.

7 Make sure the contents of your USB flash drive are visible in the Save As dialog box before you continue - to view your USB flash drive in the Save As dialog box, first click My Computer, then double-click the USB flash drive's icon (make sure you do both of these in the Save As dialog box, not on your computer's desktop).

Fill Screen: Select On to have the slide show expand small images to fill the screen. Select Off to have the slide show display small images at their original size.

Next Slide: Select Manual to disable automatic slide advance in the slide show. Select other values to make the slide show advance to the next image automatically (regardless of this setting, manual advance is always available by pressing the arrow buttons).

8 Click Save. PowerPoint will ask if you want to export every slide or only the current slide; click Every Slide. PowerPoint will save each slide in your presentation as a separate JPEG file. These files are saved in a new folder that has the same name as the original document.

Effect: Select Off to have no transition effect when changing between images during the slideshow. Select Random to use a different random effect for each transition. Select other values to use a specific effect.

9 Remove the USB flash drive from your computer and plug it into the projector's LitePort connector.

10 On the projector, navigate to the folder created in step 8 and then start the slide show (for instructions on navigating and controlling the slide show, see the Controlling LitePort section above).

Show Info: Select On to show the name of the current file and folder, the current image number, and the total number of images in the slide show at the bottom of the screen. Select Off to hide this information.

Displaying PowerPoint Slides Follow the steps below to display PowerPoint slides using LitePort (these instructions apply to PowerPoint 2007 in Windows; for other presentation programs refer to the program's instructions or help file for the steps needed to save a presentation as separate JPEG files):

1 Connect the USB flash drive to your computer.

2 Open your PowerPoint document.

3 This step is optional but improves image quality: Click the Design tab near the top of the PowerPoint document window, then click Page Setup. Click the Slides sized for drop-down menu and select Custom. Change both Width and Height to double their previous values, then click OK.

Page 41 of the InFocus IN5504 user manual — Using LitePort
Page 41 · click to enlarge
Page 41
  • If images load slowly: Make sure you are using a newer USB 2.0compatible (high speed) USB flash drive. Larger image file sizes may also slow down the player; to reduce file size, use an image editing program on your computer to resize images smaller; for the best balance between image quality and speed, resize images to be 1024 pixels wide.
  • If no images are found, or some images are not shown, or you only see folder thumbnails but no images: Make sure that images are JPEG file type (file extensions .JPEG and .JPG); other file types are not supported and will be ignored.
  • If you see a blank screen, or a logo, or the wrong input source (computer, video, etc.) instead of your images: Keep pressing the Source button on the keypad or remote until the LitePort message is displayed (if you still don't see any images, make sure the USB flash drive is correctly and completely plugged into the projector's LitePort connector).
  • If nothing happens when you connect your USB flash drive, and you cannot select the LitePort input source as described above: Check the format of your USB storage device. LitePort only supports USB storage devices formatted as FAT32. Devices formatted as NTFS, and nonstorage devices (such as cameras) are not supported.
  • If images saved by PowerPoint are low quality: Make sure to do step 3 when following the steps in the Displaying PowerPoint Slides section above.

Troubleshooting LitePort

Page 42 of the InFocus IN5504 user manual — WARNINGS:
Page 42 · click to enlarge
Page 42

Maintenance

Cleaning the lens

1 Turn the projector off and unplug the power cord.

2 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

  • Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

3 Lightly wipe the cleaning cloth over the lens in a circular motion.

WARNINGS:

  • Turn the projector off and unplug power cord before cleaning any part of the projector.
  • Do not open any cover on the projector, except the lamp cover or projector top cover.
  • Do not attempt to service this product yourself as opening and removing covers may expose you to dangerous voltage and other hazards. Refer all servicing to qualified service personnel.
InFocus IN5504 — WARNINGS: diagram (page 42)
Fig. 36
Page 43 of the InFocus IN5504 user manual — WARNINGS :
Page 43 · click to enlarge
Page 43

Replacing the projection lamp

The lamp hours timer in the Projector Info menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, the message “Replace lamp” appears on the screen at startup.

  • NOTE : Be sure to use the InFocus lamp module designed for this projector. You can order new lamps from <a href="http://www.infocus.com" rel="nofollow noopener" target="_blank">www.infocus.com</a> (in select areas), your retailer or your dealer. Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty. InFocus is not liable for the performance, safety or certification of any other lamps.

WARNINGS :

  • The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.
  • To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.
  • Unplug the power cord before replacing the lamp.
  • Do not drop the lamp module. The glass may shatter and cause injury.
  • Do not touch the glass surface of the lamp module. Fingerprints can obscure projection sharpness and may cause the glass to shatter.
  • Be extremely careful when removing the lamp housing. In the unlikely event that the lamp ruptures, small glass fragments may be generated. The lamp module is designed to contain most of these fragments, but use caution when removing it.
  • Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement.
  • When replacing the lamp while the projector is ceiling-mounted, wear protective eyewear to prevent eye injury.
  • Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See <a href="http://www.lamprecycle.org" rel="nofollow noopener" target="_blank">www.lamprecycle.org</a> .
Page 44 of the InFocus IN5504 user manual — SP-LAMP-055
Page 44 · click to enlarge
Page 44

For IN5504 and IN5502 (Single Lamp)

1 Turn the projector off and unplug the power cord.

Turn off and unplug projector

2 Wait 60 minutes to allow the projector to cool thoroughly.

3 Remove the lamp door:

(a) release the top latches by sliding the release buttons toward the rear of the projector

InFocus IN5504 — For IN5504 and IN5502 (Single Lamp) diagram (page 44)
Fig. 37 · For IN5504 and IN5502 (Single Lamp)

(b) slide the top front cover towards the direction of the lens,

(c) remove the 5 screws, then lift the lamp door off.

4 Loosen the 2 captive screws that attach the lamp housing to the projec tor. Carefully remove the lamp housing. Dispose of the lamp in an envi ronmentally proper manner in accordance with local disposal laws.

SP-LAMP-055

5 Install the new lamp housing and tighten the 2 screws.

6 Replace the lamp door by securing the 5 screws.

7 Replace the top front cover by sliding it back into place.

8 Plug in the power cord and press the Power button to turn the projector back on.

9 To reset the lamp hour timer, navigate to the Status and Service menu and select Reset Lamp Hours. See page 33 for details.

InFocus IN5504 — SP-LAMP-055 diagram (page 44)
Fig. 38

Wait 60 minutes

Page 45 of the InFocus IN5504 user manual — For IN5504 and IN5502 (Single Lamp)
Page 45 · click to enlarge
Page 45

For IN5534 and IN5532 (Dual Lamp)

InFocus IN5504 — For IN5504 and IN5502 (Single Lamp) diagram (page 45)
Fig. 39 · For IN5504 and IN5502 (Single Lamp)

1 Turn the projector off and unplug the power cord.

2 Wait 60 minutes to allow the projector to cool thoroughly.

3 Remove the lamp door:

(a) release the top latches by sliding the release buttons toward the rear of the projector,

(b) slide the top front cover towards the direction of the lens,

(c) remove the 5 screws, then lift the lamp door off.

4 Loosen the 2 captive screws that attach the first lamp housing to the pro jector. Carefully remove the lamp housing. Do the same for the second lamp housing. Dispose of the lamps in an environmentally proper man ner in accordance with local disposal laws.

5 Install the new lamp housings and tighten the 2 screws.

6 Replace the lamp door by securing the 5 screws.

7 Replace the top front cover by sliding it back into place.

8 Plug in the power cord and press the Power button to turn the projector back on.

9 To reset the lamp hour timer, navigate to the Status and Service menu and select Reset Lamp Hours. See page 33 for details.

Page 46 of the InFocus IN5504 user manual — Replacing the lens
Page 46 · click to enlarge
Page 46

Replacing the lens

1 Remove the top cover by:

InFocus IN5504 — Replacing the lens diagram (page 46)
Fig. 40 · Replacing the lens

(a) Releasing the left and right latches on both sides of the projector.

(b) Sliding the top front cover in the direction of the lens.

2 Loosen the four screws then lift the lens door.

Page 47 of the InFocus IN5504 user manual — Replacing the lens
Page 47 · click to enlarge
Page 47

3 Remove the lens by:

(a) Pushing the release lever up to release lock

InFocus IN5504 — Replacing the lens diagram (page 47)
Fig. 41 · Replacing the lens

(b) Removing the lens through the front of the projector

4 Install the new lens by:

(a) Inserting the new lens into the projector, label side up, through the

front of the projector

(b) Aligning the alignment pins at the top of the lens retaining frame

and insert into the front of the engine.

(c) Pushing the release lever down to lock the lens in place.

5 Replace the lens door by securing the 4 screws.

6 Replace the top front cover by sliding it back.

7 The cover latches lock automatically.

Page 48 of the InFocus IN5504 user manual — Using the security lock
Page 48 · click to enlarge
Page 48

Using the security lock

The projector has a security lock for use with a Cable Lock System. Refer to the information that came with the lock for instructions on how to use it.

InFocus IN5504 — Using the security lock diagram (page 48)
Fig. 42 · Using the security lock
Page 49 of the InFocus IN5504 user manual — Projected image size
Page 49 · click to enlarge
Page 49

Appendix

WUXGA Projection Distance (inch/

WXGA Projection Distance (inch/

Projected image size

Projection SizeStandard Lens

(inch/m) Minimum Maximum Minimum Maximum

Standard Lens Features and Specifications:

30/0.8 37/0.9 49/1.2 39/1.0 52/1.3

  • Motorized Zoom and Focus

40/1.0 49/1.2 65/1.7 52/1.3 69/1.7

  • Lens Shift Position: 50-110% Vertical; +/-10% Horizontal
  • F-Number: 2.0-2.32

60/1.5 74/1.9 98/2.5 77/2.0 103/2.6

  • Focal Length: 21.5-28.7

70/1.8 86/2.2 115/2.9 90/2.3 121/3.1

  • Screen Size: 30-500 inch

100/2.5 123/3.1 164/4.2 129/3.3 172/4.4

  • Zoom Ratio: 1.33:1

120/3.0 148/3.7 196/5.0 155/3.9 207/5.2

  • Throw Distance Ratio: 1.45-1.93:1 (WUXGA); 1.52-2.03:1 (WXGA)

150/3.8 184/4.7 245/6.2 193/4.9 258/6.6

200/5.1 246/6.2 327/8.3 258/6.5 344/8.7

250/6.3 307/7.8 409/10.4 322/8.2 430/10.9

300/7.6 369/9.4 491/12.5 387/9.8 516/13.1

400/10.2 492/12.5 655/16.6 516/13.1 689/17.5

500/12.7 615/15.6 818/20.8 644/16.4 861/21.9

Formulax=diag, y=dist

y=1.230x y=1.637x y=1.289x y=1.721x

m) +/-10% · m) +/-10% · Screen Size

Page 50 of the InFocus IN5504 user manual — Optional lenses
Page 50 · click to enlarge
Page 50

Optional lenses

Projection SizeFixed Short Throw

30/0.8 20/0.5 21/0.5

Fixed Short Throw Lens Features and Specifications (LENS-050):

40/1.0 26/0.7 27/0.7

  • Motorized Focus

60/1.5 39/1.0 41/1.0

  • Lens Shift Position: limited
  • F-Number: 2.2

70/1.8 46/1.2 48/1.2

  • Focal Length: 11.5

100/2.5 65/1.7 69/1.7

  • Screen Size: 30-500 inch

120/3.0 78/2.0 82/2.1

  • Zoom Ratio: n/a

150/3.8 98/2.5 103/2.6

  • Throw Distance Ratio: 0.77:1 (WUXGA); 0.81:1 (WXGA)

200/5.1 131/3.3 137/3.5

250/6.3 163/4.1 172/4.4

300/7.6 196/5.0 206/5.2

400/10.2 261/6.6 275/7.0

Activate the Lens Shift>Auto Center feature in the Basic Picture menu.

500/12.7 326/8.3 343/8.7

Formulax=diag, y=dist y=0.653x y=0.687x
Show 6 more labels / short text on this page
WUXGA Projection Distance · WXGA Projection Distance · Lens · (inch/m) +/-10% · (inch/m) +/-10% · Screen Size (inch/m)
Page 51 of the InFocus IN5504 user manual — Optional lenses
Page 51 · click to enlarge
Page 51

Short Throw Lens Features and Specifications (LENS-051):

  • Focal Length: 18.1-21.7
  • Screen Size: 30-500 inch
  • Motorized Zoom and Focus
  • Lens Shift Position: 50-110% Vertical; +/-10% Horizontal
  • Zoom Ratio: 1.20:1
  • F-Number: 2.2-3.33
  • Throw Distance Ratio: 1.21-1.45: 1 (WUXGA); 1.27-1.52:1 (WXGA)
  • Adds 1.32” (33.61mm) to the total length of the projector.
Projection SizeShort Zoom Lens

WUXGA Projection Distance (inch/m) +/-10%

WXGA Projection Distance (inch/m) +/-10%

Screen Size (inch/m) Minimum Maximum Minimum Maximum

30/0.8 31/0.8 37/0.9 32/0.8 39/1.0

40/1.0 41/1.0 49/1.2 43/1.1 52/1.3

60/1.5 62/1.6 74/1.9 65/1.6 77/2.0

70/1.8 72/1.8 86/2.2 75/1.9 90/2.3

100/2.5 103/2.6 123/3.1 108/2.7 129/3.3

120/3.0 123/3.1 148/3.7 129/3.3 155/3.9

150/3.8 154/3.9 184/4.7 162/4.1 193/4.9

200/5.1 205/5.2 246/6.2 215/5.5 258/6.5

250/6.3 257/6.5 307/7.8 269/6.8 322/8.2

300/7.6 308/7.8 369/9.4 323/8.2 387/9.8

400/10.2 410/10.4 492/12.5 431/10.9 516/13.1

500/12.7 513/13.0 615/15.6 538/13.7 644/16.4

Formulax=diag, y=dist y=1.026x y=1.230x y=1.077x y=1.289x
Page 52 of the InFocus IN5504 user manual — Optional lenses
Page 52 · click to enlarge
Page 52

Long Throw Lens Features and Specifications (LENS-052):

  • Focal Length: 28.6-54.3
  • Screen Size: 30-500 inch
  • Motorized Zoom and Focus
  • Lens Shift Position: 50-110% Vertical; +/-10% Horizontal
  • Zoom Ratio: 1.90:1
  • F-Number: 2.0-3.0
  • Throw Distance Ratio: 1.93-3.67 (WUXGA); 2.03-3.85:1 (WXGA)
  • Adds 1.8” (45.81mm) to the total length of the projector.
Projection SizeLong Throw Lens

WUXGA Projection Distance (inch/m) +/-10%

WXGA Projection Distance (inch/m) +/-10%

Screen Size (inch/m) Minimum Maximum Minimum Maximum

30/0.8 49/1.2 93/2.4 52/1.3 98/2.5

40/1.0 65/1.7 124/3.2 69/1.7 131/3.3

60/1.5 98/2.5 187/4.7 103/2.6 196/5.0

70/1.8 115/2.9 218/5.5 121/3.1 229/5.8

100/2.5 164/4.2 311/7.9 172/4.4 326/8.3

120/3.0 196/5.0 373/9.5 207/5.2 392/10.0

150/3.8 245/6.2 467/11.9 258/6.6 490/12.4

200/5.1 327/8.3 622/15.8 344/8.7 653/16.6

250/6.3 409/10.4 778/19.8 430/10.9 816/20.7

300/7.6 491/12.5 934/23.7 516/13.1 979/24.9

400/10.2 655/16.6 1245/31.6 689/17.5 1306/33.2

500/12.7 818/20.8 1556/39.5 861/21.9 1632/41.5

Formulax=diag, y=dist y=1.637x y=3.112x y=1.721x y=3.265x
Page 53 of the InFocus IN5504 user manual — Optional lenses
Page 53 · click to enlarge
Page 53

Ultra Long Throw Lens Features and Specifications (LENS-053):

  • Focal Length: 54.1-102.7
  • Screen Size: 30-500 inch
  • Motorized Zoom and Focus
  • Lens Shift Position: 50-110% Vertical; +/-10% Horizontal
  • Zoom Ratio: 1.90:1
  • F-Number: 2.3-3.19
  • Throw Distance Ratio: 3.67-6.97:1 (WUXGA); 3.85-7.32:1 (WXGA)
  • Adds 1.15” (29.11mm) to the total length of the projector.
Projection SizeUltra Long Throw Lens

WUXGA Projection Distance (inch/m) +/-10%

WXGA Projection Distance (inch/m) +/-10%

Screen Size (inch/m) Minimum Maximum Minimum Maximum

30/0.8 93/2.4 177/4.5 98/2.5 186/4.7

40/1.0 124/3.2 236/6.0 131/3.3 248/6.3

60/1.5 187/4.7 355/9.0 196/5.0 372/9.5

70/1.8 218/5.5 414/10.5 229/5.8 435/11.0

100/2.5 311/7.9 591/15.0 326/8.3 621/15.8

120/3.0 373/9.5 709/18.0 392/10.0 745/18.9

150/3.8 467/11.9 887/22.5 490/12.4 931/23.6

200/5.1 622/15.8 1182/30.0 653/16.6 1241/31.5

250/6.3 778/19.8 1478/37.5 816/20.7 1552/39.4

300/7.6 934/23.7 1773/45.0 979/24.9 1862/47.3

400/10.2 1245/31.6 2364/60.1 1306/33.2 2483/63.1

500/12.7 1556/39.5 2955/75.1 1632/41.5 3104/78.8

Formula x=diag. y=dist. y=3.112x y=5.911x y=3.265x y=6.207x

Page 54 of the InFocus IN5504 user manual — SplitScreen Compatibility
Page 54 · click to enlarge
Page 54

SplitScreen Compatibility

Splitscreen allows two distinct sources to be displayed simultaneously. Switch primary sources, make picture adjustments and choose one of multiple display options: either two side by side horizontal or vertical source regions, or a small secondary source image displayed on top of the primary source in one of four placement options.lets you show two different sources at the same time. See page 28 for details. The following source combinations are supported:

Table 2:

HDMI1 HDMI2 VGA1 VGA2 BNC Component S-video Composite DisplayLink LitePort

HDMI1 X HDMI2 X VGA1 X VGA2 X BNC X Component X S-video X Composite X DisplayLink X LitePort X

Page 55 of the InFocus IN5504 user manual — Control commands
Page 55 · click to enlarge
Page 55

Control commands

A read command returns the range and the current setting, for example:

IMPORTANT: When formatting commands sent from a control system or computer, enclose commands in parentheses “(“ and “)”. When entering custom commands into Scheduled Tasks in the projector’s web interface, enclose commands in less than/ greater than symbols “” instead. Serial Communication Configuration Visit our website for additional RS-232 settings and information. To control this projector via RS-232, connect a null modem cable and set the control system serial port settings to match the following communication configuration:

Brightness (BRT?) (0-100, 50)

Volume (VOL?) (0-100, 50)

Lamp Hours (LMP?) (0-32766, 42)

A write request example: (AAA####) where (starts the command AAA denotes the command #### denotes the value to be written (leading zeros not necessary) ) ends the command Some commands have ranges, while others are absolute. If a number greater than the maximum range is received, it is automatically set to the maximum number for that function. If a command is received that is not understood, a "?" is returned. With absolute settings, "0" is off, 1-9999 is on. The one exception is the Power command, where 0 is off and 1 is on. To assure the projector can process a command, wait 3 seconds before entering the next command.

Bits per second 115,200

Network Communication Configuration For network control, you can access the projector through Port 23 (Telnet). We use the same control codes on serial as we do over the network. InFocus network control uses the Telnet packet structure. Command Format All commands consist of 3 alpha characters followed by a request, all enclosed in parentheses. The request can be a read request (indicated by a "?") or a write request (indicated by 1 to 4 ASCII digits).

Brightness (BRT100) Sets the brightness to 100

Power (PWR0) Turns power off

A read request example: (AAA?) where (starts the command AAA denotes the command ? denotes the read request ) ends the command

Power (PWR1) Turns power on

Show 11 more labels / short text on this page
Read Command Examples · Function Command Response · RS-232 Port Settings · Setting Value · Data bits 8 · Parity None · Stop bits 1 · Flow control None · Emulation VT100 · Write Command Examples · Function Command Response
Page 56 of the InFocus IN5504 user manual — CLC RW 0 2 0 1
Page 56 · click to enlarge
Page 56

Error Conditions Not all commands are supported for all projectors. If an unsupported command is issued, the command will be ignored. If a command is received that is not understood, a ‘?’ character will be returned indicating the command was not understood. Limitations The projector cannot respond to commands coming in at a high-rate. Therefore, a delay must occur between commands to ensure that the command gets properly executed. To assure the projector can process a command, wait 3 seconds before entering the next command. The Step column refers to increasing or decreasing the menu bar position since the On-screen Display is not an exact match of values. For example, Step 2 changes the data by 2 through the CLI (Command Line Interface). The menu bar is up (or down) by 1.

Auto Keystone 0Off 1: On 2: Temp. Disabled

AVK RW 0 2 0 1

Auto Off Time 0: Never 1: 5 minutes 2: 10 minutes 3: 15 minutes 4: 20 minutes 5: 25 minutes 6: 30 minutes

AOT RW 0 6 6 1

Com mand RW Min Max Default Step

Auto Source 0Disable; 1: Enable ASC RW 0 1 1 1
AC Power On 0Disable; 1: Enable APO RW 0 1 0 1
Blank Screen 0Disable; 1: Enable BLK RW 0 1 0 1
Always On Function 0Off 1: Network 2: DisplayLink 4: Monitor Out 8: 5-Volt DC

SPS RW 0 15 0 1

Blank Screen Style 0: Blue screen 1: Timer 2: Test patterns 3: Black screen 4: White screen 5: Factory logo 6: Snapshot

BSS RW 0 6 0 1

Aspect Ratio 0Auto 1: Native 2: 4:3 3: 16:9 4: Letterbox 5: Panorama 6: 16:10

ARZ RW 0 6 0 1

Brightness BRT RW 0 100 50 1

BrilliantColorTM 0Normal; 1: Bright BCL RW 0 1 1 1
Ceiling 0Off; 1: On; 2: Auto CEL RW 0 2 2 1
Auto Image 1Enable AIM W n/a 1 1 1
Closed CaptionsNonMuted) 0: Off; 1: CC1; 2: CC2

CLC RW 0 2 0 1

Function

Page 57 of the InFocus IN5504 user manual — DLM RW 0 2 2 1
Page 57 · click to enlarge
Page 57
Closed CaptionsMuted 0: Off; 1: CC1; 2: CC2 CLM RW 0 2 1 1

Custom Key 0: Blank screen 1: Mute 3: Aspect ratio 4: Source 5: Auto image 6: Freeze screen 8: Source info 10: Projector info 14: Overscan 15: AV mute 16: Closed captions 17: SplitScreen

EFK RW 0 17 8 1

Color CLR RW 0 100 50 1

Color Space 0RGB 1: REC709 2: REC601 3: RGB Video 4: Auto

CSM RW 0 4 4 1

Color Temp 0Warmest 1: Warm 2: Cool 4: Bright

TMP RW 0 4 Source Specific 1

Detect Film 0Disable; 1: Enable TTO RW 0 1 1 1

Digital Zoom DZM RW 0 100 100 5

Contrast CON RW 0 100 50 1

Disable Snapshots 1Disabled (Flash needed to re-enable.)

DCP RW 0 1 0 1

Current Source 0: DisplayLink 1: VGA 1 2: VGA 2 3: RGBHV 4: LitePort 5: HDMI 1 6: HDMI 2 7: Component 8: S-video 9: Composite

SRC RW 0 9 0 1

DisplayLink Source Enable1

USS W 1

Dual Lamp Auto Switch 0On Failure Only 1: At Power Up 50 & higher; Hours

DLA RW 0 2000 0 50

Dual Lamp Error Identifier 0: No lamp error 1: Lamp #1 error 2: Lamp #2 error 3: Both lamp error

DLE R 0 3 0 1

Dual Lamp Mode 0Lamp 1; 1: Lamp 2 2: Both lamps

DLM RW 0 2 2 1

? = Query

Page 58 of the InFocus IN5504 user manual — FCR RW 0 2 0 1
Page 58 · click to enlarge
Page 58

DynamicBlackTM (single lamp version only) 0: Auto 1: 100% 2: 90% 3: 80%... 10: 10%

DYB RW 0 10 1 1

Gamma 2Video 3: Film 5: Bright 7: CRT

GTB RW 0 7 Source Specific 1

Glow Ring 0Disable; 1: Enable GLO RW 0 1 1 1

Error Condition 0: No error 1: Lamp not lit after 5 attempts 3: Lamp went out unexpectedly 4: Fan failure 5: Overtemperature 6: Low voltage

ERR R 0 6 0 1

Help 0Disable; 1: Enable HLP RW 0 1 0 1

Help Customization HLC RW 0 1 0 1

Horz. Keystone DKH RW 0 100 50 1

Horz. Pincushion HPC RW 0 100 50 1

Horz. Position HPS RW 0 100 50 1

Horz. Shift DSH RW 0 100 50 1

Factory Reset 1Reset RST W n/a 1 1 1
Internal Sound Enable 0Disable; 1: Enable INT RW 0 1 1 1
Fast Color Refresh 0Off 1: Video only 2: On (all sources)

FCR RW 0 2 0 1

Key Click 0Disable; 1: Enable KCL RW 0 1 1 1
Keypad Enable 0Disable; 1: Enable KPE RW 0 1 1 1

Flesh Tone Correction FTC RW 0 100 0 10

Force Wide 0Disable; 1: Enable FWM RW 0 1 1 1

Lamp 1 High Power Hours ? = Query

LMO R 0 n/a 1

Freeze Screen 0Disable; 1: Enable FRZ RW 0 1 0 1

Lamp 1 Low Power Hours ? = Query

LME R 0 n/a 1

Friendly Name PFN RW string n/a n/a

Lamp 1 ResetsTotal number ? = Query

LMR R 0 n/a 1

Lamp 1 Total Hours ? = Query

LMP R 0 n/a 1

? = Query

Page 59 of the InFocus IN5504 user manual — LTS RW 0 12 0 1
Page 59 · click to enlarge
Page 59

Lamp 2 High Power Hours ? = Query

LDN R 0 n/a 1

LitePort Auto Start 0Disable; 1: Enable LAS RW 0 1 1 1

Lamp 2 Low Power Hours ? = Query

LDL R 0 n/a 1

LitePort Effect 0: Off 1: Random 2: Fade 3: Horz Wipe 4: Vert Wipe 5: Diagonal Wipe 6: Horz Split 7: Vert Split 8: Horz Bars 9: Vert Bars 10: Spiral 11: Diamond 12: Blocks

LTS RW 0 12 0 1

Lamp 2 ResetsTotal number ? = Query

LDR R 0 n/a 1

Lamp 2 Total Hours ? = Query

LDH R 0 n/a 1

Lamp Life ? = Query

LIF R n/a 2000

Lamp Low Power 0Disable; 1: Enable IPM RW 0 1 0 1
LitePort Fill Screen 0Disable; 1: Enable LFS RW 0 1 0 1

Language 0: English 1: French 2: German 3: Italian 5: Korean 6: Norwegian 7: Portuguese 8: Russian 9: Simp Chinese 10: Spanish 11: Trad Chinese 12: Swedish 13: Dutch 14: Polish 15: Turkish 16: Danish 17: Finnish

LAN RW 0 17 0 (9 for China models)

LitePort Next Slide 0Disable; 1: Enable LAD RW 0 4 0 1
LitePort Show All Folders 0Disable; 1: Enable LPA RW 0 1 0 1
LitePort Show Info 0Disable; 1: Enable LSI RW 0 1 0 1
LitePort Source Command 0Disable; 1: Enable PPS RW 0 1 0 1
Magnify Controls 0Disable; 1: Enable MGC RW 0 1 1 1

Magnify Horz. Position MGH RW 0 100 50 5

Lens Adjust Enable 0Disable; 1: Enable MLL RW 0 1 1 1

Magnify Level MGL RW 0 100 50 5

Magnify Vertical Position MGV RW 0 100 50 5

Page 60 of the InFocus IN5504 user manual — MNL RW 0 15 0 1
Page 60 · click to enlarge
Page 60

Map Source Audio n Values SA0 = DisplayLink SA1 = VGA 1 SA2 = VGA 2 SA3 = RGBHV SA4 = HDMI1 SA5 = HDMI2 SA6 = LitePort SA7 = Component SA8 = S-video SA9 = Composite

SAnx RW 0 9 Source Specific 1

Menu Transparency 0Opaque; 90: 90% Trans. TOE RW 0 90 0 5
Motorized Focus Further 1Execute MFF W 1 1
Motorized Focus Nearer 1Execute MFN W 1 1
Motorized Lens Shift Ctr 1Execute MHC W 1 1
Motorized Lens Shift Dwn 1Execute MVD W 1 1

x Values 0: Off 1: AOUSB 2: Audio In 1 3: Audio In 2 4: Audio In 3 5: Audio In 4 6: Audio In 5

Motorized Lens Shift Left 1Execute MHL W 1 1
Motorized Lens Shift Right 1Execute MHR W 1 1
Motorized Lens Shift Up 1Execute MVU W 1 1
Menu 0Clear; 1: Display MNU RW 0 1 0 1
Motorized Zoom In 1Execute MZI W 1 1

Menu Lockout 1: Basic Picture 2: Adv Picture 4: Setup Menu 8: Status & Service 15: All Menus

MNL RW 0 15 0 1

Motorized Zoom Out 1Execute MZO W 1 1
Mute 0Disable; 1: Enable MTE RW 0 1 0 1

Menu Navigation 0: Menu Key 1: Up Key 2: Down Key 3: Select Key 4: Left Key 5: Right Key

NAV W 0 5 n/a 1

Network Default Gateway GT1 = 1st Octet GT2 = 2nd Octet GT3 = 3rd Octet GT4 = 4th Octet

GTn RW 0 255 0 1

Network DHCP 0Disable; 1: Enable DHP RW 0 1 1 1

Menu Offset OFF RW 0 100 0 10

Page 61 of the InFocus IN5504 user manual — DSC RW 0 9 1 1
Page 61 · click to enlarge
Page 61

Network DNS DN1 = 1st Octet DN2 = 2nd Octet DN3 = 3rd Octet DN4 = 4th Octet

DNn RW 0 255 0 1

PIN Entry Menu = m Up = u Down = d Select = s Source = i

PET RW string n/a

Network Factory Reset 1Reset NFR W 1 1

Network Host Name HSN RW string n/a n/a

PIN Protect Disable0; Enable: 1

PIV RW 0 1 0 1

Network Host Name Lookup (WINS) 0: Disable; 1: Enable

HNL RW 0 1 0 1

Power 0Turn On; 1: Turn Off PWR RW 0 1 0 1

Network IP Address IP1 = 1st Octet IP2 = 2nd Octet IP3 = 3rd Octet IP4 = 4th Octet

IPn RW 0 255 0 1

Power Sounds 0Disable; 1: Enable ACE RW 0 1 1 1

Power-up Source 0: DisplayLink 1: VGA 1 2: VGA 2 3: RGBHV 4: LitePort 5: HDMI 1 6: HDMI 2 7: Component 8: S-video 9: Composite

DSC RW 0 9 1 1

Network MAC Address ? =- Query

MAD R string n/a

Network Restart 1Restart NTR W 1 1

Network Subnet Mask NM1 = 1st Octet NM2 = 2nd Octet NM3 = 3rd Octet NM4 = 4th Octet

NMn RW 0 255 0 1

Presets 2: User 5: Presentation 7: Video 8: ISF Day 9: ISF Night 10: Bright 11: Whiteboard 12: Blackboard 13: Beige wall

PST RW 0 13 Source Specific 1

Noise Reduction NRL RW 0 100 50 1

Overscan 0Off; 1: Zoom; 2: Crop OVS RW 0 2 0 1

Phase MSS RW 0 100 50 1

PCG RW string n/a

Default = imuds · PIN Change PCG“default,new”

Page 62 of the InFocus IN5504 user manual — SHP RW 0 4 2 1
Page 62 · click to enlarge
Page 62
Prevent PC Screen Saver 0Disable; 1: Enable NND RW 0 1 1 1

Screen Save Time 0: never 1: 5 minutes 2: 10 minutes 3: 15 minutes 4: 20 minutes 5: 25 minutes 6: 30 minutes

SSV RW 0 6 0 1

Projector Current Lamp ? = Query

Projector Firmware Ver ? = Query

Projector High Power Hours ? = Query

LTO R 0 n/a

Search Screen 0Factory logo 1: Blue 2: Snapshot 3: Black 4: White

DSU RW 0 4 0 1

Projector Info menu 1Display PRI W 1 1

Projector Low Power Hours ? = Query

LTE R 0 n/a

Serial Port Baud Rate 0: 2400 1: 4800 2: 9600 3: 14400 4: 19200 5: 38400 6: 57600 7: 115200 8: 1200

BR1 RW 0 8 7 1

Projector Model ? = Query

Projector Resolution ? = Query

Projector Serial No. ? = Query

Serial Port Echo 0Disable; 1: Enable EC1 RW 0 1 0 1

Projector Total Hours ? = Query

LMT R 0 n/a

Set Black Level 1Set BLC W 1 1
Rear Project 0Disable; 1: Enable REA RW 0 1 0 1
Sharpness 0Max 1: High 2: Normal 3: Low 4: Minimum

SHP RW 0 4 2 1

Reset Lamp Hours 1reset lamp 1 2: reset lamp 2

LRT RW 1 2 n/a 1

Save User Presets 1 1Save USI W 1 1
Show Messages 0Disable; 1: Enable DMG RW 0 1 0 1
Show 5 more labels / short text on this page
DLI R string · FVS R string · MDL R string · NRS R string · USN R string
Page 63 of the InFocus IN5504 user manual — SSY RW 0 7 0 1
Page 63 · click to enlarge
Page 63
Show Network Messages 0Disable; 1: Enable DNG RW 0 1 1 1

Source Info - Signal Format ? = Query

Sleep Timer 0Off 1: 2 hours 2: 4 hours 3: 6 hours

SLT RW 0 3 0 1

Source Info - Sync Type ? = Query

Source Info - Vert Refresh ? = Query

Source 1-4 Commands SR1 = Source Key 1 SR2 = Source Key 2

SRn RW SR1 = VGA1 SR2 = VGA2 SR3 = HDMI1

Source Name (0-9) * = Factory Names SNn RW string

SplitScreen Enable 0Disable; 1: Enable SSC RW 0 1 0 1

Source Advance - PC CAD+ W n/a n/a +

Source Advance - Video VAD+ W n/a n/a +

SplitScreen 2nd Source 0: Off 1: DisplayLink 2: VGA 1 3: VGA 2 4: RGBHV 5: HDMI 1 6: HDMI 2 7: Component 8: S-video 9: Composite

SSL RW 0 9 Source Specific - See User Guide SplitScreen Matrix in Appendix

Source Info menu 1Display ABT W 1 1

Source Info - Active Source Name ? = Query

Source Info - Aspect Ratio ? = Query

Source Info - Color Gamut ? = Query

SplitScreen 2nd Source Location 0: Right 1: Bottom 2: Left 3: Top 4: PiP bottom right 5: PiP bottom left 6: PiP top left 7: PiP top right

SSY RW 0 7 0 1

Source Info - Color Space ? = Query

Source Info - Horz Refresh ? = Query

Source Info - Pixel Clock ? = Query

SplitScreen 2nd Source Size 0small; 1: medium; 2: large SSZ RW 0 2 2 1

Source Info - Resolution ? = Query

Show 10 more labels / short text on this page
QSF R string · QST R string · QVR R string · QAS R string · QAR R string · QCG R string · QCS R string · QHR R string · QPC R string · RES R string
Page 64 of the InFocus IN5504 user manual — RCO GCO BCG
Page 64 · click to enlarge
Page 64
SplitScreen Swap 1enable SSS W 1 1

Volume VOL RW 0 100 50 1

White Peaking WPK RW 0 100 100 10

Sync Threshold STH RW 0 100 50 5

Dynamic Messaging (max53 characters)

PRN RW string n/a n/a

System State 1: Off 2: Start Up 3: PIN 4: Search 7: Source Displayed 9: Blank Screen 12: Cool Down 13: Screen Save 17: Flash Update 18: Error

SYS R 1 18 7 1

Escape codes: \c - Initialize (Box mode) \d -Initialize (Ticker Bottom mode) \u - Initialize ticker top mode \e - Solid background \f - Transparent background \1 - Small font size \2 - Large font size \n - New line \a - Beep \tnnn - Timer \b - Start blink \s - Stop blink \” - Print a double quote character \’ - Print a single quote character \\ - Print a backslash character

Take Snapshot 1Capture CAP W 1 1

Test Pattern Select TPS RW 0 21 9 1

Tint TNT RW 0 100 50 1

Tracking MTS RW 0 100 50 1

USB Audio Enable 0Disable; 1: Enable USA RW 0 1 1 1

Vertical Keystone DKV RW 0 100 50 1

ExamplePRN”This is line1\nThis is line 2”

Vertical Pincushion VPC RW 0 100 50 1

Vertical Position VPS RW 0 100 50 1

Red Gain Green Gain Blue Gain

RCG GCG BCG

RW 0 100 50 1

Vertical Shift DSV RW 0 100 50 1

Video Standard 0Auto 1: NTSC 2: PAL 5: SECAM

VSU RW 0 5 0 1

Red Offset Green Offset Blue Offset

RCO GCO BCG

RW 0 100 50 1

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No start up screen.Plug the power cord into the projector then press the power button. p.17
No start up screen. p.17
Only the start up screen appears. SS eta rtu np B c reIf your computer is using the projector's DisplayLink connector, see the DisplayLink Software User's Guide for troubleshooting information. Press the Source button to activate the laptop’s external port. Restart laptop p.17
Only the start up screen appears. SS eta rtu np B c re p.17
No computer image, just the words “Signal out of range.” rangeSignal out of B thePress the Auto Image button on the keypad or remote. To adjust computer refresh rate, go to Control Panel > Display > Settings > Advanced > Adapter (location varies by operating system). You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped.” p.18
No computer image, just the words “Signal out of range.” rangeSignal out of B the p.18
Only my laptop’s background appears, not the Desktop icons. BDisplayLink - Use DisplayLink software to change the display mode from Extended Desktop to Duplicated Desktop. Windows - Disable “Extend my Windows Desktop” in Control Panel > Display > Settings > Display 2 (location varies by operating system). Uncheck this option, then click Apply p.18
Only my laptop’s background appears, not the Desktop icons. B p.18
Image fuzzy or cropped A ASet your computer’s display resolution to the native resolution of the projector (Start > Settings > Control Panel > Display > Settings tab). For a laptop, disable laptop monitor or turn- on dual-display mode p.19
Image not centered on screen.Adjust Lens Shift in the Basic Picture menu. p.19
Image not square.Adjust Keystone in the Basic Picture menu. p.20
Image not sharp.Adjust Sharpness in the Basic Picture menu. p.20
Image does not fit 4:3 or 16:9 screen.Change aspect ratio to 4:3 or 16:9 in Basic Picture>Aspect Ratio menu. p.20
Image upside down. ATurn off Ceiling Mount in Setup menu. p.21
Image reversed left to right. ATurn off Rear Project in Setup menu. p.21
Projected colors don’t match source. COLORAdjust color, tint, brightness, contrast in the Basic Picture menu and/or color space in the Advanced Picture menu. p.21
The video embedded in my PowerPoint presentation does not play on the screen. B BIf your computer is using the projector's DisplayLink connector, see the DisplayLink Software User's Guide for video troubleshooting information. Turn off the internal LCD display on your laptop. p.22
The video embedded in my PowerPoint presentation does not play on the screen. B B p.22
Lamp won’t turn on, Temperature light is on. Temperature lightMake sure vents aren’t blocked, turn the projector off and allow it to cool for one minute. p.22
Lamp won’t turn on, Temperature light is on. Temperature light p.22
“Replace lamp” message appears at startup, lamp won’t turn on, Lamp light is turned on. Lamp lightLamp must be replaced (see page 42). Lamp door Replace lamp p.23

Ask about the InFocus IN5504

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus IN5504

Be the first to ask — other owners or our team will answer.

Original document

InFocus IN5504 manual PDF

66 pages·7.6 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…