Instruction/ maintenance manual of the product IN124A InFocus
Go to page of 50
.
1 Declaration of Conformity Manufacturer: InFo cus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon 97223-8368 USA We decl are und er our s ole resp on sibility that this p rojector c o.
2 Table of Contents Introduction 4 Positioning the projector 6 Connecting a computer source 7 VGA connection 7 USB connection 7 HDMI connection 7 Connecting power 7 Optional computer connections 7 Dis.
3 Important Oper ating Cons iderations for Safety • Refer to this guide for proper startup and shutdown procedures. • Follow all warnings and cautions in this manual and on the projecto r. • Place the projector in a ho rizontal position no greater than 15 degrees o ff axis.
4 Introduction Your new digital projector is simple to co nnect, easy to use, and st raightforward to maintain. It is a versatile projector that is flexible enough fo r business presentatio ns and home video viewing too.
5 Connector panel The projector provides both co mputer and video connection optio ns, including: • VGA computer (2) • Composite video •H D M I •S - v i d e o • USB B connector (for projecto.
6 Positioning the projector To determine where to position the projector, co nsider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipmen t. He re are some general guidelin es: • Position the pro jector on a flat surface at a right angle t o the screen.
7 Connecting a computer source VGA connection Connect one end of the provided compu ter cable to the Co mputer 1/Computer 2 connector on the projecto r and the other to the VGA connector on yo ur computer. If you are using a de sktop comp uter, you w ill need to discon nect the monitor cable fro m the computer’s video port f irst.
8 Displaying an image Press the Power button. The Power LED lights blue, and the fans start to run. When the lamp comes on, the start up screen displays. It can t ake up to a minute fo r the image to achieve full brightness. Note: When the feature, AC Power On, is enabled, th e projector autom atically turn s on when power is connected.
9 Adjusting the image If necessary, adjust th e height of the projector by ro tating the elevator fo ot to extend the foot. If necessary, rotate th e leveling foot located at the rear of th e projector. Avoid placin g your ha nds near the hot exhau st vent at t he front of th e projecto r.
10 Connecting a video device You can connect v ideo devices such as VCRs, DV D players, camcor ders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the pr ojector.
11 Shutting down the projector Auto Off Time The projector also has an Auto Off Time feat ure that automatically turns the proj ector off after no active sou rces are detected an d no user interaction wit h the projector is per formed for 30 minutes. By def ault, this feature is of f.
12 Problem Solution Result No start up screen Plug power cord into the projector press the Power button Correct image Only start up screen appears Pres s the SOURCE button.
13 Problem Solution Result No computer image, just the words “Signal out of range” Press the Auto Image button on remote Adjust computer refresh rate (Windows 7: Control Panel > Display > Screen Resolution > Advanced Settings > Adapter tab).
14 Image fuzzy or cr opped Change the computer's "Resolution" setting to match the projector's resolution (Windows 7: Control Panel > Display > Screen Resolution).
15 Image not square Adjust Keystone on keypad Square image Image not sharp Adjust Sharpness in the Basic Menu Correct image Image does not fit 4:3 or 16:9 screen Change aspect ratio to 4:3 or 16:9 in .
16 Image upside down Turn off Ceiling Mount in Basic menu Correct image Image reverse d left to right Turn off Rear Project in Advanced Menu > Setup > Image Setup... menu Correct image Projected colors don’t match source Adjust the items in the Advanced Menu > Image > Color.
17 The video embedded in my PowerPoint presentation does not play on the screen Turn off the internal LCD display on your laptop Embedded video plays correctly Lamp won’t turn on, the projector is o.
18 Still need assistance? If you need ass istance, visit our website at www.infoc us.com/support or call us. See the Quick Start Guide for support co ntact information. This product is backed by a limite d warranty. An extended war ranty plan may be purcha sed from your dealer.
19 Using the remote control The remote uses two (2) AAA batteries (not provided). They are easily installed by removing the cover from the remote’s back, aligning the + and - ends of the batteries, sliding them in to place, and then replacing the cover.
20 Using the audio Using the projector’s speakers Connect the audio source to the Audio 1/Audio 2 conn ectors to hear audio through the projector speakers. Amplified speakers may also be connected to the pro jector using the Audio Out connector. To adjust the volume, pres s the Volume buttons on the remote.
21 Using the keypad buttons Most buttons are descri bed in detail in oth er sections, but here is an overview of their functions: Power –turns the projector on and off (page 8). Right arrow - When the menu is displayed, the right arrow button navigates through the menu.
22 Optimizing computer images After the projector is running and the image is on the screen, you can optimize the image using the onscreen menu s. For general information on using the m enus, see page 24. • Select default image settings using a preset appropriate to your environment.
23 Optimizing video images After your video d evice is connected properly and the i mage is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 24. • Adjust the Keystone, Contrast, Brightness, Co lor, or Tint ( page 25 ).
24 Using the menus 1 To open the menus, press the Menu button on the ke ypad or remote. (The menus automatically cl ose after 60 second s if no buttons are pre ssed.) Use the arrow buttons to move up and down to review the menu options. 2 To enter a submenu, highlight the desi red submenu and pres s > on the keypad or Select on remot e.
25 Basic Menu To adjust the following setti ngs, highlight the setting, use the right and left arrows to adjust the values. Aspect Ratio : Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9.
26 Advanced Menu Image: 3D Control: 3D: allows you to enjoy 3D (ster eoscopic) content. Your projector suppor ts Auto, Top-Bottom, Frame Sequential , Frame Packing, Side-by-Side for c ontrolling LCD shut - ter glasses. In addition to th e projector, yo u will need a pair of 3D shutter glasses, 3D content, a nd 3D com patible so urce.
27 Setup: Audio Setup... Intern al Spea kers : turns the int ernal speaker on or of f. Computer 1 : selects the audio i nput for Computer 1 signal. Computer 2 : selects the audio i nput for Computer 2 signal. Video : selects the audio input for video source .
28 Lamp... Programmed Dimming : When enabled, Programmed Dim ming enhances contrast ratios, lamp life and system noise performanc e. Lamp power will change continuously based on the brightness of the pr ogram content. Note: Image anomalies may be seen when image scenes change from dark to light (or light to dark).
29 Timer Auto Off Time : automati cally turns the p rojector of f after no signals are detected for a preset number of minutes. If an active sign al is received before the projecto r powers down, the image will be displayed.
30 network list, and press Sel ect / Enter . 4 Press Select / Enter to display o n-screen keyboard, enter the password from the on-s creen key board, then pres s Menu to close the keybo ard. 5 Highlight OK and press Select / Enter to wait for connecting successfully.
31 3 To access the Admin page, enter the password. The default password is “0000”. • Information: Displays the status, wired LAN, and wireless LAN information. • Email Alert: Allows yo u to setup the mail server and send system error messages to your network administrator.
32 Using EZ Display i. 4 to 1 Display : To display up to 4 computers simultan eously, click on the location you want to display to. If you only have 2 computers, choose L (left) or R (right). To display in full screen mode, click All . You can change the location at an y time.
33 3 Select WLAN from source list. AP Info page displays. 4 Establish WiFi connection with your source device first, and launch EZ Disp lay/ EZ Remote app on your mobile device. EZ Remote Launch EZ Remote. You w ill see the connecte d device shown o n the device list.
34 EZ Display: Streaming Doc To stream your documents, transfer th e documents you want from the computer to your mobile de vice and disconnect your mobile device. Documents wil l be organized by their format type. Select a file to display it wirelessly.
35 EZ Display: Streaming Web The web browser will be dis played over WiFi. The S ketch and Save functions are also supported. This feature requires a Client Mode internet conn ection. See page 29 for more details. Select Web browser, and enter t he passcode on the Client Info page.
36 EZ Display: Quad Split Screen EZ Display allows 4 different sources to be displayed in the same screen. Through Split Screen Control, you can decide whe re your current display shoul d be placed.
37 Mac OS: For information about this, refer to the EZ USB Display Manual at www.infocus.c om/ support. Displaying pictures with a USB storage device When a USB source is inserted into the proj ector USB-A connector, press the Source key and use the arrow keys to highlight the USB icon.
38 Photo mode Folders and supported files are represented in thumbnail view. Displaying a picture • To open/close the Photo View toolbar: press the Menu key. • To navigate through the toolbar: press the arrow keys ^/</>. • To return to thumbn a il view: press the Select / Enter key.
39 Video mode Video playlist is displayed on the sc reen When a video is playing • To open the Video Viewer toolbar: press the Menu key. • To return to video playlist: press the Select / Enter key when the toolbar is closed.
40 Audio mode The Audio playlist is displayed on the screen. When audio is playing • To return to audio playlist: press the Menu key. K ey Action Up Go to the previou s audio file Down Go to the nex.
41 Office viewer mod e The file list is displayed on the screen. When an Office file is displaying • To go to the next page: press the down arrow key. • To go to the previous page: press the up arrow key. • To scroll up: press the left arrow key.
42 Se ttings •P r e s s t h e Select / Enter to enter the selected item. Press the Menu key to exit. * WiFi on ly works wh en the InF ocus wir eless dongle (p/n SP-WIF IUSB-2) is connected.
43 Supported file formats • Images • Audio • Voice Record • Video Image Format Profile Color Space Size Limitati on JPEG Baseline YUV400 No limit YUV420 No limit YUV422 No limit YUV440 No limi.
44 • Subtitle Note: Mixed subtitle codes are NOT supported. • Office Viewer Format Font Subtitle Size Standard SRT UTF-8 / UTF-16 4bits up to 448x200 2bits up to 896 x200 File Format Support Version Pages/Lines Limita tion Size Limitation Comment Adobe PDF PDF 1.
45 Maintenance Cleaning the lens 1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth. • Projector must b e off and the le ns must be at room temperat ure. • Avoid using an ex cessive amount of clean er, and don’t apply the c leaner directly to the lens.
46 Replacing the projection lamp The Lamp Hours timer in the Projector Info me nu counts the number of hours the lamp has been in use. • NOTE : Be sure to us e the InFocus lamp module des igned for this projector. You can order new lamps from www.infocus.
47 1 Turn off the projector and unplug the power cord. 2 Wait 60 minutes to allow the projector to cool tho roughly. 3 Remove the lamp door, located on top of the projector, by removing the screw on the side of the lamp door, sliding the doo r forward, and lift ing the lamp door off.
48 Numerics 3D Sync Invert 26 A AC Power On 28 AP Mode 29, 42 Aspect Ratio 25 Audio 1/Audio 2 7 Auto Image 25 Auto Keystone 25 Auto Off Time 29 Auto Source 28 AV Mute 27 B Blank Key 27 Blank Screen 27.
49 O only 26 Overscan 26, 27 P Phase 26 PIN Protect 28 Power connecto r 7 Power cord 7 Power Saving Mode 28 Prevent PC Screen Saver 2 6 Programmed Dimming 28 Projector Connecting vide o devices 10 Key.
An important point after buying a device InFocus IN124A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought InFocus IN124A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data InFocus IN124A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, InFocus IN124A you will learn all the available features of the product, as well as information on its operation. The information that you get InFocus IN124A will certainly help you make a decision on the purchase.
If you already are a holder of InFocus IN124A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime InFocus IN124A.
However, one of the most important roles played by the user manual is to help in solving problems with InFocus IN124A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device InFocus IN124A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
