EN
InFocus logo
Official user manual

InFocus IN12

35 pages·1.6 MB·Projector·PDF·ENDEFRITNLJA
InFocus IN12
Table of Contents 45 sections Contents · About this manual... · Operation During Projection · Image Operations During Projection · … ShowHide
Page 1 of the InFocus IN12 user manual
Page 1 · click to enlarge
Page 1
InFocus IN12 diagram (page 1)
Fig. 1
Page 3 of the InFocus IN12 user manual — Reattaching the Lens Cover............................................................................ 34
Page 3 · click to enlarge
Page 3

Replacing the Lamp 26

To check the current lamp use time 26 When to replace the lamp 27 Replacing the Lamp 27 To replace the lamp 28 Resetting the Lamp Time 29 To reset the lamp time 30 To reset the lamp time after exceeding the lamp life 30

Appendix 31

Remote Controller Signal Range 31

Connecting to a Component Video Output Device ......................................... 32

Full-screen Display of an RGB Image 33

Reattaching the Lens Cover 34

About this manual...

z All of the operations in this manual are explained using the remote controller that comes

with the projector. The following key operations can also be performed on the projector instead of the remote controller: [MENU], [S], [T], [X], [W], [ENTER], [ESC], [ ], [INPUT], [AUTO], [ZOOM +], [ZOOM –], [FOCUS S], [FOCUS T].

To perform this remote controller operation:Use this projector button: [ENTER]Button in the center of the cursor keys [ZOOM +], [ZOOM –][ZOOM] button in combination with the [W] and [X] buttons [FOCUS S], [FOCUS T][FOCUS] button in combination with the [S] and [T] buttons
Page 4 of the InFocus IN12 user manual — Adjusting Image Brightness
Page 4 · click to enlarge
Page 4
InFocus IN12 — Operation During Projection diagram (page 4)
Fig. 2 · Operation During Projection

Operation During Projection

This section explains the various types of operations you can perform while the projector is projecting an image.

Image Operations During Projection

You can perform the following operations while projecting an image. z Image brightness adjustment z Color mode selection z Image zooming z Momentary cut off of the input source image and projection of a black or blue screen, or

a logo z Image freeze z Pointer display in the projected image z Aspect ratio switching (between 4:3 and 16:9)

Adjusting Image Brightness

To adjust image brightness 1 Press the [BRIGHT] key.

z This displays the brightness adjustment window.

InFocus IN12 — Adjusting Image Brightness diagram (page 4)
Fig. 3 · Adjusting Image Brightness

2 Use the [W] and [X] keys to adjust image brightness. 3 To hide the window, press the [ESC] key.

Page 5 of the InFocus IN12 user manual — Selecting the Color Mode
Page 5 · click to enlarge
Page 5

Selecting the Color Mode

You can select from among five different color mode settings to optimize the projected image in accordance with image contents and projection conditions.

To change the color mode 1 Press the [COLOR MODE] key.

z This displays the color mode selection window. The currently selected color mode is the

one whose button is selected (filled in).

InFocus IN12 — Selecting the Color Mode diagram (page 5)
Fig. 4 · Selecting the Color Mode

2 Use the [T] and [S] keys to move the highlighting to the color mode you want to select, and then press the [ENTER] key.

z This will select the button next to the highlighted color mode name. z For details on what each color mode does, see “Color Mode” under “Image Adjustment

Main Menu” on page 14. 3 To hide the window, press the [ESC] key.

Zooming an Image 1 Press the [D-ZOOM +] or [D-ZOOM –] key.

z This will cause to appear in the projected image. 2 Use the cursor keys to move the to the part of the image that you want in the center of the enlarged image. 3 Press (or hold down) the [D-ZOOM +] key.

z Each press of the [D-ZOOM +] key enlarges the image one step. Holding down the

[D-ZOOM +] key continually enlarges the image. z Pressing the [D-ZOOM –] key while an image is enlarged reduces the zooming by one

step. Holding down the [D-ZOOM –] key continually reduces the size of the image. z While an image is zoomed, you can use the cursor keys to scroll the view to other

parts of the image. 4 To exit the zoom operation, press the [ESC] key.

Page 6 of the InFocus IN12 user manual — Freezing an Image
Page 6 · click to enlarge
Page 6

Momentarily Cutting Off the Input Source Image 1 Press the [BLANK] key.

z This temporarily cuts off the image from the input source and projects a black screen in

its place. 2 To resume projection of the image from the input source, press the [BLANK] key (or [ESC] key).

Note

You can specify projection of a black screen or blue screen, or a logo. For details, see “Blank Screen” under “Screen Settings Main Menu” on page 18.

Freezing an Image

Pressing the [FREEZE] key freezes the projected image.

To freeze the projected image 1 While an image is being projected from an input source, press the [FREEZE] key.

z This will capture the image that is on the screen at the moment you press [FREEZE]

and stores it in projector memory. That image remains projected on the screen. 2 To restore projection of the image from an input source, press the [ESC] key.

Page 7 of the InFocus IN12 user manual — To clear the pointer from the image
Page 7 · click to enlarge
Page 7

Displaying a Pointer in the Projected Image

You can select from among eight different pointer styles, including various arrow styles, for display in the projected image. Pointers can be used during a presentation to indicate or highlight a specific part of the image.

InFocus IN12 — Displaying a Pointer in the Projected Image diagram (page 7)
Fig. 5 · Displaying a Pointer in the Projected Image
InFocus IN12 — Displaying a Pointer in the Projected Image diagram (page 7)
Fig. 6 · Displaying a Pointer in the Projected Image
InFocus IN12 — Displaying a Pointer in the Projected Image diagram (page 7)
Fig. 7 · Displaying a Pointer in the Projected Image

Arrow 1 Oval 1 Spot 2

Note

Depending on the pointer style you are using, the pointer may not display properly when you are using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE –] keys to change the keystone correction value to zero.

To display a pointer in the image 1 Press the [POINTER] key.

z This will cause a pointer to appear in the image. z You also can use the setup menu to specify the pointer type that appears first when you

press the [POINTER] key. For details, see “Pointer” under “Option Settings 2 Main Menu” on page 22. 2 Use the cursor keys to move the pointer to the location you want.

For this pointer type:Pressing [STYLE] will do this: Arrow 1 / Arrow 2Rotate the arrow by 90 degrees Bar 1 / Bar 2Toggle between flashing and not flashing Oval 1 / Oval 2Toggle between flashing and not flashing Spot 1 / Spot 2Cycle the darkness (transparency) of the area not covered by the spot among two levels

To select the pointer type 1 Press the [POINTER] key to display the pointer. 2 Keep pressing the [POINTER] key until the pointer you want is displayed.

z Each press of the [POINTER] key cycles through the available pointer types.

To clear the pointer from the image

Press the [ESC] key.

Page 8 of the InFocus IN12 user manual — To turn the Eco Mode on or off
Page 8 · click to enlarge
Page 8

Changing the aspect ratio of the projected image

Press the [ASPECT] key to toggle the aspect ratio of the displayed image between 4:3 and 16:9.

Note

z The aspect ratio setting affects the projected image only when the input source is

VIDEO or component. z When the input source is a component signal with an aspect ratio of 16:9, the

aspect ratio switches automatically to 16:9. When this happens, pressing the [ASPECT] key will not change the aspect ratio. z You also can change the aspect ratio setting using the setup menu. For details, see

“Aspect Ratio” under “Screen Settings Main Menu” on page 16.

Important!

Eco Mode

Turning on the Eco Mode reduces lamp brightness to save power. The projector’s cooling fan also operates at a slower speed while the Eco Mode is turned on, which results in quieter operation. Turn on the Eco Mode when your priority is quieter operation. Turn off the Eco Mode when your priority is maximum brightness.

To turn the Eco Mode on or off

Press [ECO] to toggle the Eco Mode on and off.

Page 9 of the InFocus IN12 user manual — Using the [FUNC] Key
Page 9 · click to enlarge
Page 9

Using the [FUNC] Key

Pressing the [FUNC] key displays the menu shown below.

InFocus IN12 — Using the [FUNC] Key diagram (page 9)
Fig. 8 · Using the [FUNC] Key

You can use this menu to perform the operations described below. z Adjust image brightness

Highlight “Brightness” and then press the [ENTER] key. • This performs the same operation as pressing the [BRIGHT] key ( key) described on page 3. z Turn the Eco Mode on or off

Highlight “Eco Mode” and then press the [ENTER] key. • This performs the same operation as pressing the [ECO] key (U key) described on page 7. z Select the aspect ratio of the projected image

Highlight “Aspect Ratio” and then press the [ENTER] key. • This performs the same operation as pressing the [ASPECT] key ( key) described on page 7.

Page 10 of the InFocus IN12 user manual — To exit the setup menu
Page 10 · click to enlarge
Page 10

Configuring Advanced Projector Settings

Your projector has a setup menu that you can use to configure advanced settings.

Basic Setup Menu Operations

Displaying the Setup Menu

Pressing the [MENU] key displays the menu shown below in the center of the projection screen.

InFocus IN12 — Basic Setup Menu Operations diagram (page 10)
Fig. 9 · Basic Setup Menu Operations

Main menu The main menu includes seven main menu items. The currently selected main menu item is the one that is highlighted.

Sub-menu The sub-menu shows each individual setting under each main menu item, and its current setting.

Guidance text Guidance text provides a brief description of the main key operations available for the operation you are currently performing.

Note

You can position the setup menu in the center or on the left edge of the projection screen. For details, see “Menu Position” under “Option Settings 1 Main Menu” on page 20.

To exit the setup menu

Press the [MENU] key.

Configuring Setup Menu Settings 1 Press the [MENU] key to display the setup menu. 2 Use the [T] and [S] keys to select the main menu item you want by highlighting it. 3 Press the [ENTER] key. 4 Use the [T] and [S] keys to select the sub-menu item you want by highlighting it. 5 Perform the required operation on the selected sub-menu item screen.

z The guidance text explains the operations you need to perform to configure each setting. 6 To return to the main menu from the sub-menu, press the [ESC] key. 7 To exit the setup menu, press the [MENU] key.

Page 11 of the InFocus IN12 user manual — Note
Page 11 · click to enlarge
Page 11

Basic Setup Menu Example

  • The procedure below shows how to configure the following three settings:
  • Image Adjustment J Contrast
  • Image Adjustment J Color Mode
  • Option Settings 1 J Eco Mode

Note

z Certain settings on the setup menu cannot be changed while there is no input signal

to the projector. Because of this, you should configure setup menu settings after selecting an input source and starting projection. z This example covers basic steps only. For more detailed information, see “Setup Menu

Contents” on page 13.

To configure the “Image Adjustment J Contrast” setting 1 Press the [MENU] key to display the setup menu. 2 “Image Adjustment” is initially selected on the main menu, so simply press the [ENTER] key. 3 Press the [T] key once to select “Contrast”.

InFocus IN12 — Note diagram (page 11)
Fig. 10 · Note

4 Use the [W] (lighter) and [X] (darker) keys to adjust contrast.

To configure the “Image Adjustment J Color Mode” setting 1 Press the [T] key once to select “Color Mode”. 2 Press the [ENTER] key.

z This displays the color mode menu.

InFocus IN12 — Note diagram (page 11)
Fig. 11 · Note

3 Use the [T] and [S] keys to select the color mode you want. 4 After selecting the color mode you want, press the [ESC] key.

Page 12 of the InFocus IN12 user manual — Basic Setup Menu Example
Page 12 · click to enlarge
Page 12

To configure the “Option Settings 1 J Eco Mode” setting 1 Press the [ESC] key.

2 Press the [T] key three times to select “Option Settings 1”.

3 Press the [ENTER] key.

4 Press the [T] key three times to select “Eco Mode”.

InFocus IN12 — Basic Setup Menu Example diagram (page 12)
Fig. 12 · Basic Setup Menu Example

5 Use the [W] and [X] keys to select “On” or “Off”.

6 After you are finished, press the [MENU] key to exit the setup menu.

Page 13 of the InFocus IN12 user manual — Note
Page 13 · click to enlarge
Page 13

Restoring Projector Settings to Their Initial Factory Defaults

You can use the procedures in this section to restore all of the settings on a particular main menu or all of the settings on the setup menu to their initial factory defaults.

To restore all settings on a particular main menu to their initial factory defaults 1 Press the [MENU] key to display the setup menu. 2 Use the [T] and [S] keys to select the main menu whose settings you want to restore to their initial factory defaults.

z You can select Image Adjustment, Screen Settings, Input Settings, Option Settings 1, or

Option Settings 2. 3 Press the [ENTER] key. 4 Use the [T] key to select “Restore Menu Defaults”. 5 Press the [ENTER] key.

z This will display a confirmation screen like the screen shown below.

InFocus IN12 — Restoring Projector Settings to Their Initial Factory Defaults diagram (page 13)
Fig. 13 · Restoring Projector Settings to Their Initial Factor…

6 Use the [S] key to select “Yes”. 7 To restore the settings of the main menu to their initial defaults, press the [ENTER] key.

z To exit the operation without doing anything, press [ESC] instead of [ENTER]. 8 After you are finished, press the [MENU] key to exit the setup menu.

Note

z The language setting and the password are not returned to their initial factory defaults

if you select Option Settings 1 in step 3. z For details about how the above procedure initializes settings, see the explanations of

the settings under “Setup Menu Contents” on page 13.

Page 14 of the InFocus IN12 user manual — Setup Menu Contents
Page 14 · click to enlarge
Page 14

To restore all settings on the setup menu to their initial factory defaults 1 Press the [MENU] key to display the setup menu. 2 Use the [T] key to select “Restore All Defaults”, and then press the [ENTER] key.

z This displays a confirmation message asking if you want to initialize all settings. 3 Use the [S] key to select “Yes”. 4 To restore all settings on the setup menu to their initial defaults, press the [ENTER] key.

z This will restore all of the settings to their initial factory defaults, except for the

Language, Lamp Time, and password settings. z To exit the operation without doing anything, press [ESC] instead of [ENTER]. 5 After you are finished, press the [MENU] key to exit the setup menu.

Setup Menu Contents

This section contains tables that provide detailed explanations of all of the items included on the setup menu. The following describes the type of information that appears in each of the columns of the tables.

Setting Name This column shows the names of the settings as they appear on the sub-menu.

Input This column shows the input source for which each setting is supported. Input source names are abbreviated as R (RGB input), C (component video input), and V (video input). The letter N indicates that the setting can be configured while there is no input signal.

Setting Unit The setting unit indicates how a setting is stored. “Source Specific” in this column indicates that separate settings can be stored for each individual input source. For example, you could store an “Image Adjustment J Brightness” setting of –1 for RGB input and a setting of +1 for VIDEO input. “Single” in this column indicates that a single setting is stored and applied, regardless of the input source.

Description This column provides details about the setting item and how to select it. The initial default setting is indicated by an asterisk (*).

Page 15 of the InFocus IN12 user manual — Image Adjustment Main Menu
Page 15 · click to enlarge
Page 15

Image Adjustment Main Menu

Brightness RCVU Source Specific

Use this sub-menu to adjust the brightness of the projected image. A larger value produces a brighter image.

Contrast RCVU Source Specific

Use this sub-menu to adjust the contrast of the projected image. A larger value produces a stronger contrast.

Sharpness RCV Source Specific

Use this sub-menu to adjust the sharpness of the outlines in the projected image. A larger value makes the image sharper, while a smaller value makes it softer.

Saturation RCV Source Specific

Use this sub-menu to adjust the color saturation of the projected image. A larger value increases color saturation.

Tint RCV Source Specific

Use this sub-menu to adjust the tint of the projected image. A larger value makes the overall image more bluish, while a smaller value makes the overall image more reddish. This setting is supported only when the signal is NTSC or NTSC4.43.

Color Mode RCVU Source Specific

You can select from among five different color mode settings to optimize the projected image in accordance with image contents and projection conditions. Presentation*: Use this setting for standard presentations in a well-lit area. This is the initial default setting when the input source is RGB. Standard: Use this setting when you want to highlight the colors of your presentation. Graphics: Use this setting when you want photographs and graphics to appear natural. Theater*: Use this setting to bring out the dark portions of your images. This is the initial default setting when the input source is either component video or video. Blackboard: Use this setting for easy viewing when projecting onto a blackboard.

Color Balance RCVU Source Specific

This sub-menu lets you adjust the color balance of the projected image. Color balance lets you select either “Color Temperature” or “Color” (for individual adjustment of red, green and blue) as the adjustment method. Color Temperature: Select this option when you want to adjust the color temperature. Selecting “LO” gives whites a reddish cast, while “HI” gives them a bluish cast. Selecting “NORM*” sets a medium setting between the two colors. Color: Select this option when you want to individually adjust the intensity of red, green, and blue. For all of the colors, a larger value makes the color stronger.

Page 16 of the InFocus IN12 user manual — Important!
Page 16 · click to enlarge
Page 16

Use this sub-menu to adjust the vertical position of the input source image within the projection area.

Use this sub-menu to adjust the horizontal position of the input source image within the projection area.

Frequency R Signal Specific

When vertical bands appear in the projected image while RGB is selected as the input source, it means that the frequency setting is not correct. When this happens, use this setting to adjust the frequency manually.

Important!

If, for some reason, your manual frequency settings cause the image input from the computer to disappear from the projection, you can press the [AUTO] key to perform an auto adjust operation, which should cause the image to appear.

Phase R Signal Specific

When there is flickering in the projected image while RGB is selected as the input source, it means that the phase setting is not correct. When this happens, use this setting to adjust the phase manually.

Video Mode RCV Source Specific

This setting is valid when VIDEO is selected as the input source. Use it to select a mode that is optimized for movies or still images. Normal*:

Optimized for movies. Still Image:

Optimized for still images. In particular, this setting should be used when projecting still images from a digital camera connected to the projector’s VIDEO terminal.

Use this sub-menu to return all of the sub-menu items on the Image Adjustment main menu to their initial default settings. z Restoring menu defaults when there is no input signal

will restore defaults for the currently selected input source. z “Image Adjustment” main menu “Vertical Position”,

“Horizontal Position”, “Frequency”, and “Phase” defaults can be restored for the current signal type (XGA/60Hz, SXGA/60Hz,etc.) only.

Show 6 more labels / short text on this page
Vertical Position · RCV Signal Specific · Horizontal Position · RCV Signal Specific · Restore Menu Defaults · RCVU Source Specific
Page 17 of the InFocus IN12 user manual — Important!
Page 17 · click to enlarge
Page 17

About the “Signal Specific” Setting Unit

For the items that have “Signal Specific” in the “Setting Unit” column of the above table, the setting is saved for the specific type of signal (XGA/60Hz, SXGA/60Hz, etc.) that is being input when the setting is performed, and not for a specific input source.

Screen Settings Main Menu

RCVUN Single Use this sub-menu to correct vertical keystoning of the projected image.

Aspect Ratio RCV Source Specific

Use this sub-menu to select one of the following aspect ratios for the projected image. 4:3*: This setting specifies a 4:3 aspect ratio, which is the same as a standard television. 16:9: This setting specifies a 16:9 aspect ratio, which is the same as a movie screen, high-definition TV, etc. Using this setting when the input source image is a 16:9 image that has been squeezed to a 4:3 image causes the image to be projected with its normal 16:9 aspect ratio.

Note

When the input source is a component signal with an aspect ratio of 16:9, the aspect ratio switches automatically to 16:9. When this happens, the aspect ratio cannot be changed using this setting.

Important!

Keystone Correction

Page 18 of the InFocus IN12 user manual — Screen Settings Main Menu
Page 18 · click to enlarge
Page 18

RCVUN Single Use this sub-menu to specify whether projection will be from the front of the screen or the back of the screen.

*: Select this option when projecting from the front of the screen.

: Select this option when projecting from the back of the screen.

: Select this option to flip the back-projected image vertically.

: Select this option to flip the image vertically.

Startup Screen RCVUN Single Use this sub-menu to specify whether or not a startup screen should be projected whenever the projector is turned on. Logo: Select this option to project the projector’s built-in logo screen at startup. None*: Select this option when you do not want to project a startup screen.

RCVUN Single Use this sub-menu to specify what should be projected when there is no input signal to the projector. Blue*: Select this option to project a blue screen. Black: Select this option to project a black screen. Logo: Select this option to project the projector’s built-in logo screen.

Projection Mode · No Signal Screen

Page 19 of the InFocus IN12 user manual — Screen Settings Main Menu
Page 19 · click to enlarge
Page 19

Blank Screen RCVUN Single Use this sub-menu to specify what should be projected after the [BLANK] key is pressed. Blue: Select this option to project a blue screen. Black*: Select this option to project a black screen. Logo: Select this option to project the projector’s built-in logo screen.

Use this sub-menu to return all of the sub-menu items on the Screen Settings main menu to their initial default settings. z Restoring menu defaults when there is no input signal

will restore defaults for the currently selected input source. z Note that the “Keystone Correction”, “Projection Mode”,

“Startup Screen”, “No Signal Screen”, and “Blank Screen” settings are always returned to their initial defaults, regardless of the currently selected input source.

Restore Menu Defaults · RCVUN Source Specific

Page 20 of the InFocus IN12 user manual — Input Settings Main Menu
Page 20 · click to enlarge
Page 20

Input Settings Main Menu

RGB Input RCUVN Single Use this sub-menu to specify manually the type of signal being input from the projector’s RGB input terminal. Auto*: Automatically detects the signal being input from the RGB input terminal and configures the appropriate input protocol. RGB: Select this option when a computer is connected to the RGB input terminal. For details about connecting a computer, see “Connecting a Computer to the Projector” in the “User’s Guide”. Component: Select this setting when the projector’s RGB input terminal is connected to the component video output terminal of a video device using an optionally available YK-3 component video cable. For information about connection, see “Connecting to a Component Video Output Device” on page 32.

Video Signal RCVUN Single Use this sub-menu to specify manually the type of signal being input from the projector’s VIDEO input terminal. Auto*: Select this setting to have the projector switch the video signal system automatically in accordance with the input signal from the video device that is connected to the VIDEO input terminal. NTSC / NTSC4.43 / PAL / PAL-M / PAL-N / PAL60 / SECAM: Each setting selects the applicable video system. Use these settings when you want to specify only one specific video signal for the VIDEO input terminal.

RCVUN Single Use this sub-menu to specify whether or not the name of the currently selected signal source should be displayed in the projected image. On*: Select this option to turn on display of the name of the currently selected signal source in the projected image. Off: Select this option to turn off display of the signal source name.

Use this sub-menu to return all of the sub-menu items on the Input Settings main menu to their initial default settings. z Restoring menu defaults when there is no input signal

will restore defaults for the currently selected input source. z Note that the “Signal Name Indicator” setting is always

returned to its initial default, regardless of the currently selected input source.

Signal Name Indicator · Restore Menu Defaults · RCVUN Source Specific

Page 21 of the InFocus IN12 user manual — Option Settings 1 Main Menu
Page 21 · click to enlarge
Page 21

Option Settings 1 Main Menu

Menu Position RCVUN Single Use this sub-menu to specify the display position of the setup menu as either the center or the left side of the screen.

*: Select this option to display the setup menu in the center of the screen.

: Select this option to display the setup menu on the upper left corner of the screen.

RCVUN Single Use this sub-menu to turn auto keystone correction on or off. On*: Select this option to turn on auto keystone correction. Off: Select this option to turn off auto keystone correction.

Auto Adjust RCVUN Single Use this sub-menu to specify whether or not auto adjust should be performed when RGB is selected as the input source. On*: Select this option to turn on auto adjust. Off: Select this option to turn off auto adjust.

Eco Mode RCVUN Single Use this sub-menu to turn the Eco Mode on or off. On: Select this option to reduce lamp brightness and save power. This setting also reduces the speed of the projector’s cooling fan, which reduces operation noise. Off: Select this option to project at maximum brightness.

RCVUN Single Use this sub-menu to turn Auto Power Off on or off. See “Turning Off the Projector” in the “User’s Guide” for more information. On*: Select this option to turn on Auto Power Off. Off: Select this option to turn off Auto Power Off.

RCVUN Single You can configure the projector to require input of a password before operation is enabled.

Auto Keystone Correction · Auto Power Off · Power On Password

Page 22 of the InFocus IN12 user manual — Important!
Page 22 · click to enlarge
Page 22

RCVUN Single Use this sub-menu to turn Direct Power On on or off. See “Direct Power On” in the “User’s Guide” for more information. On: Select this option to turn on Direct Power On. Off*: Select this option to turn off Direct Power On.

Important!

While Direct Power On is enabled, the projector will turn off automatically if no key operation is performed and no signal input is received within about 10 minutes after it is turned on. This is true regardless of the current Auto Power Off setting.

Language RCVUN Single Use this sub-menu to specify the language to use for messages, setup menus, etc. English / French / German / Italian / Spanish / Swedish / Chinese (Simplified) / Chinese (Traditional) / Korean / Japanese

RCVUN Single This sub-menu returns all of the sub-menu items on the Option Settings 1 main menu to their initial default settings. z Restoring menu defaults when there is no input signal

will restore defaults for the currently selected input source. z The “Auto Adjust” item is returned to its initial default

only when RGB input is selected for the input source. All of the other items are returned to their initial defaults regardless of the currently selected input source.

Direct Power On · Restore Menu Defaults

Page 23 of the InFocus IN12 user manual — Option Settings 2 Main Menu
Page 23 · click to enlarge
Page 23

Option Settings 2 Main Menu

Zoom Memory RCVUN Single Use this sub-menu to turn zoom memory on or off. Zoom memory lets you save the zoom setting when the projector is turned off, so it can be restored automatically the next time the projector is turned on. On*: Select this option when you want to restore the zoom setting that was in effect when the projector was last turned off, whenever it is turned on. Off: Select this option when you want the image to be projected at its maximum size whenever you turn on the projector.

Pointer RCVUN Single Use this sub-menu to specify the type of pointer that appears first when you press the [POINTER] key. Arrow 1* / Arrow 2 / Bar 1 / Bar 2 / Oval 1 / Oval 2 / Spot 1 / Spot 2

RCVUN Single This sub-menu returns all of the sub-menu items on the Option Settings 2 main menu to their initial default settings.

Restore Menu Defaults

Page 24 of the InFocus IN12 user manual — Operational Info Main Menu
Page 24 · click to enlarge
Page 24

Operational Info Main Menu

Lamp Time RCVUN Single This sub-menu item shows the cumulative number of hours the current lamp has been used to date. Use this value as a reference when deciding whether or not the current lamp needs to be replaced. For details about replacing the lamp, see “Replacing the Lamp”.

RCVUN Single Use this submenu item to reset the lamp time to 0 hours after replacing the lamp. For details about replacing the lamp and the lamp time reset operation, see “Replacing the Lamp”.

Input Signal RCVUN Source Specific

This sub-menu item shows the currently selected input signal (RGB, Component, or VIDEO). “-” is indicated here when there is no input signal.

Signal Name RCV Source Specific

This sub-menu item shows the signal name of the signal being input to the projector.

Index RC Source Specific

This sub-menu item appears only when RGB or component is the input signal. It shows projector internal information.

Resolution R Single This sub-menu item appears only when RGB is the input signal. It shows the number of vertical pixels of resolution of the RGB input signal.

This sub-menu item shows the horizontal frequency of the input signal.

This sub-menu item shows the vertical frequency of the input signal.

Scan System RC Source Specific

This sub-menu item appears only when RGB or component is the input signal, and shows the scanning frequency of the input signal. The input signal is interlace or non-interlace for an RGB signal input, and interlace or progressive for a component signal input.

Show 5 more labels / short text on this page
Reset Lamp Time · Horizontal Frequency · RCV Source Specific · Vertical Frequency · RCV Source Specific
Page 25 of the InFocus IN12 user manual — Restore All Defaults Main Menu
Page 25 · click to enlarge
Page 25

Restore All Defaults Main Menu

RCVUN Single This sub-menu returns all sub-menu items on all main menus to their initial default settings. This operation can be performed regardless of the currently selected input source and regardless of whether or not a signal is currently being input. For details about this procedure, see “To restore all settings on the setup menu to their initial factory defaults” on page 13.

RCVUN Single This sub-menu item shows the cumulative operating time of this unit. This time cannot be initialized.

Restore All Defaults · Unit Operating Time

Page 26 of the InFocus IN12 user manual — Cleaning Intake and Exhaust Vents
Page 26 · click to enlarge
Page 26

User Maintenance

Cleaning the Projector

Periodically clean the projector exterior, lens, intake vents, and exhaust vents on a regular basis.

Important!

z Always make sure that the projector has cooled sufficiently before cleaning it. If the

projector is turned on, perform the following steps before cleaning it. 1 Turn off the projector. 2 Check to make sure that the POWER/STANDBY indicator has changed to amber. 3 Unplug the power cord from the power outlet, and allow the projector to cool down for about 60 minutes.

Cleaning the Projector Exterior

Wipe the exterior of the projector with a soft cloth that has been moistened in a weak solution of water and a mild neutral detergent. Be sure to wring all excess moisture from the cloth before wiping. Never use benzene, alcohol, thinner, or any other volatile agent for cleaning.

Cleaning the Lens

Carefully wipe the lens with a commercially available lens cloth or optical lens paper, like those for eyeglasses or camera lenses. When cleaning the lens, be very careful to avoid scratching it.

Cleaning Intake and Exhaust Vents

Dust and dirt tend to collect around the intake vents located on the back and both sides of the projector. Because of this, you should use a vacuum cleaner to clean away accumulated dust and dirt periodically as shown below.

Page 27 of the InFocus IN12 user manual — Replacing the Lamp
Page 27 · click to enlarge
Page 27

Important!

z Continued use of the projector after dust has accumulated around the intake vents

can cause overheating of internal components and lead to malfunction. z Certain operating conditions also can cause dirt and dust to accumulate around the

projector's exhaust vents on the front. If this happens, use the same procedure as that described above to clean the exhaust vents.

Replacing the Lamp

z The light source lamp is a consumable item. The average life of a lamp is approximately

2000 hours. After 2000 hours, a message appears to alert you to the need of lamp replacement. However, note that the characteristics of a particular lamp or lamp operating conditions can cause the lamp to start to go dim or even fail before the message appears.

To check the current lamp use time 1 Press the [MENU] key to display the setup menu. 2 Press the [T] key to select the “Operational Info” main menu.

InFocus IN12 — Replacing the Lamp diagram (page 27)
Fig. 14 · Replacing the Lamp

z The “Lamp Time” sub-menu item shows the

number of hours that the current lamp has been used. 3 Press the [MENU] key to exit the setup menu.

Page 28 of the InFocus IN12 user manual — Replacing the Lamp
Page 28 · click to enlarge
Page 28

When to replace the lamp

The LAMP indicator starts to flash red and the message shown below appears whenever the lamp time exceeds 2000 hours.

It is time to replace the lamp. Use the procedure in the User’s Guide to replace the lamp as soon as possible.

When this message appears, replace the lamp as soon as possible using the procedure under “Replacing the Lamp” on page 27. Note that the above message will disappear about 10 seconds after you turn on the projector, even if you do not replace the lamp. You will be able to continue using the projector without replacing the lamp until the lamp time reaches 100 hours. At that time, the LAMP indicator will stop flashing and remain lit red, the following message will appear for about 10 seconds, and then the projector will turn off automatically.

The lamp has exceeded its service life! The projector will not turn on until you replace the lamp.

When this message appears, replace the lamp immediately using the procedure under “Replacing the Lamp” on page 27.

Replacing the Lamp

replacing the lamp, turn off the projector and wait for the cool down operation (indicated when the POWER/STANDBY indicator is flashing amber) to finish. Next, disconnect the AC power cord from the projector, and wait for at least 60 minutes to allow it to cool down even further. Touching the lamp or the area around it during operation or immediately after turning off the projector creates the risk of serious burn injury. z Replace the lamp using the SP-LAMP-029 optional lamp cartridge only. z A mercury lamp with high internal pressure is used as the light source. A lamp that

is weakened by impact, damage, or expiration of its lamp life may explode or fail to light if exposed to loud noise. Note that lamp life differs greatly from lamp to lamp, and is affected by conditions under which the lamp is used. z Never touch the glass of the lamp with your fingers. Doing so can cause the lamp to

rupture and shorten its life. z A broken lamp can cause glass fragments to be scattered inside the lamp housing.

Gas inside of the lamp housing may also be discharged from the projector’s vent exhaust ports. Gas inside of the lamp includes mercury, so be sure to ventilate the area whenever the lamp breaks. Should you accidentally inhale gas fumes or should gas fumes get into your eyes, immediately contact a physician. z Should the lamp break, take care to avoid personal injury on the glass fragments.

Never try to replace a broken lamp on your own. Contact InFocus service (www.infocus.com/service) to request a replacement.

Page 29 of the InFocus IN12 user manual — Important!
Page 29 · click to enlarge
Page 29

To replace the lamp

Important!

When replacing the lamp, use the special screwdriver that comes with the SP-LAMP-029 replacement lamp. The projector does not come with a screwdriver.

1 Turn off the projector and unplug its AC power cord. 2 Wait for about 60 minutes to allow the projector’s current lamp to cool down completely. 3 Turn over the projector and place it on top of a desk or on some other stable surface. 4 Loosen the lamp cover screw, and then remove the lamp cover.

InFocus IN12 — Important! diagram (page 29)
Fig. 15 · Important!

5 Loosen the three screws indicated by an S mark.

Lamp cartridge

Page 30 of the InFocus IN12 user manual — Resetting the Lamp Time
Page 30 · click to enlarge
Page 30

6 Use the lamp cartridge handle to pull the lamp cartridge from the projector.

InFocus IN12 — Resetting the Lamp Time diagram (page 30)
Fig. 16 · Resetting the Lamp Time

7 Insert the new lamp cartridge as far as it will go, as shown in the illustration.

z After inserting the lamp cartridge, lay its handle down in the position shown in the

illustration under step 5 on this page.

InFocus IN12 — Resetting the Lamp Time diagram (page 30)
Fig. 17 · Resetting the Lamp Time

Make sure the grooves of the lamp cartridge align with the grooves of the lamp housing.

z After replacing the lamp, be sure to perform the procedure under “Resetting the Lamp

Time” on page 29.

Resetting the Lamp Time

The lamp time reset operation you need to perform depends on when you replace the lamp.

It is time to replace the lamp. Use the procedure in the User’s Guide to replace the lamp as soon as possible.

If you replace the lamp when the above message appears, use the procedure under “To reset the lamp time”.

The lamp has exceeded its service life! The projector will not turn on until you replace the lamp.

If you replace the lamp after the above message appears, use the procedure under “To reset the lamp time after exceeding the lamp life”.

Page 31 of the InFocus IN12 user manual — To reset the lamp time after exceeding the lamp life
Page 31 · click to enlarge
Page 31

To reset the lamp time 1 Turn on the projector. 2 Press the [MENU] key to display the setup menu. 3 Press the [T] key to select “Operational Info”, and then press the [ENTER] key. 4 Press the [ENTER] key. 5 This causes the message “Reset Lamp Time?” to appear. 6 Press the [S] key to select “Yes”, and then press the [ENTER] key. 7 This resets the lamp time to 0 hours. 8 Press the [MENU] key to exit the setup menu. 9 This causes the setup menu to disappear from the projected image.

To reset the lamp time after exceeding the lamp life

If you use the existing lamp until its life is exceeded, you will not be able to turn on the projector even after you replace the lamp with a new one. Perform the following procedure to initialize the lamp time in this case, which will make it possible to turn on the projector. 1 Use the bundled AC power cord to plug the projector into a power outlet.

z Connecting to a power outlet causes the POWER/STANDBY and LAMP indicators on the

top of the projector to light red, which indicates that the lamp has exceeded its service life. 2 While holding down the projector’s [W] key, hold down the [AUTO] key for about five seconds.

z This will reset the lamp time, cause the POWER/STANDBY indicator to change from red

to amber, and also cause the LAMP indicator to go out. 3 Press the [ ] (power) key to ensure that the projector turns on normally.

Page 32 of the InFocus IN12 user manual — Important!
Page 32 · click to enlarge
Page 32

Appendix

Remote Controller Signal Range

When performing an operation on the remote controller, point it at the remote control signal receiver on the back or front of the projector. The following illustration shows the range of the remote controller signal.

InFocus IN12 — Appendix diagram (page 32)
Fig. 18 · Appendix

Remote Controller Range

The allowable distance between the remote controller and the projector is less when there is a sharp angle between the remote controller and the remote control signal receiver.

Important!

To avoid running down the battery, store the remote control unit so its buttons are not pressed inadvertently.

Page 33 of the InFocus IN12 user manual — Important!
Page 33 · click to enlarge
Page 33

Connecting to a Component Video Output Device

Some video devices are equipped with a component video output terminal. You can use an optionally available VESA to component video adapter (SP-VESA-ADPT-R) and a component video cable to connect the RGB input terminal of the projector to the component video output terminal of a video device.

Important!

Always turn off the projector and the video device before connecting them.

InFocus IN12 — Important! diagram (page 33)
Fig. 19 · Important!

z Component video output terminals come in 3-terminal sets: Y·Cb·Cr or Y·Pb·Pr. Be sure to

match the colors of the plugs on the optional adapter with the colors of the terminals (Green: Y; Blue: Cb/Pb; Red: Cr/Pr). z Note that connection only to an analog component video output terminal is supported.

Connection to a digital output terminal is not supported.

Page 34 of the InFocus IN12 user manual — 800 × 600
Page 34 · click to enlarge
Page 34

Full-screen Display of an RGB Image

The projector outputs images using XGA (1024 pixels × 768 pixels) video resolution. When the input signal from the computer connected to the projector is not an XGA signal, “Resize Image To Fit” automatically enlarges or reduces the image so it matches the projector’s video resolution and fills the entire screen. The following shows how different input signals from a computer are adjusted during projection.

Input Signal Example Projected Image

800 × 600

1024 × 768

1280 × 1024

When the input signal has a resolution of 1280 × 1024 (aspect ratio: 5:4), the original image is compressed so it conforms to the projection resolution of 1024 × 768 (aspect ratio: 4:3). Because of this, the projected image may appear slightly wider horizontally than the original image.

Page 35 of the InFocus IN12 user manual — Reattaching the Lens Cover
Page 35 · click to enlarge
Page 35

Reattaching the Lens Cover

Use the following procedure to replace the lens cover if it should accidentally become detached from the projector. 1 Insert the nub (‘) of the left tab of the lens cover into the depression () of the tab under the lens.

z When performing the above step, make sure that the lens cover is open to 90 degrees in

relation to the front of the Data Projector.

2 Keeping the left nub (‘) in the left depression (), gently press the lens cover towards the right as you insert the nub (’) of the right lens cover tab into the depression () of the right tab under the lens.

z Do not apply undue force to the lens cover when performing the above step. Pressing too

strongly can damage the tabs of the lens cover.

Press here with a pen or similarly pointed object as you slide the cover into place.

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the InFocus IN12

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus IN12

Be the first to ask — other owners or our team will answer.

Original document

InFocus IN12 manual PDF

35 pages·1.6 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…