
User’s Guide


Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Other specific Country Approvals may apply, please see product certification label.
InFocus reserves the right to alter product offerings and specifications at any time.
This Class A digital apparatus complies with Canadian ICES-003.
This user’s guide applies to models C170 and GEN205.
We declare under our sole responsibility that this projector conforms to the following
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
This is a Class A product. In a domestic environment it may cause radio interference,
Microsoft, PowerPoint, Word, Excel and Windows are trademarks or registered trade-
trademarks of Adobe Systems Incorporated. InFocus, ASK Proxima, LiteShow, Lite-
vide reasonable protection against harmful interference when the equipment is oper-
ated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio communications. Operation of
in which case the user may be required to take adequate measures. The typical use is
marks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered
This equipment has been tested and found to comply with the limits for a Class A
this equipment in a residential area is likely to cause harmful interference in which
Port, and LP are trademarks or registered trademarks of InFocus Corporation.
case the user will be required to correct the interference at his own expense.
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
EMC Directive 89/336/EEC, Amended by 93/68/EEC
in a conference room, meeting room or auditorium.
EN 61000-3-3
directives and norms:
EN 55024

projector, refer to this User’s Guide. Electronic versions of this User’s Guide
in multiple languages are available on the included CD and on our website.
If you are experienced in setting up presentation systems, use the included
The website also has technical specifications (an interactive image size cal-
product data sheet), a web store to buy accessories, and a page for online
Quick Set Up card. For complete details on connecting and operating the
culator, laptop activation commands, connector pin outs, a glossary, the
registration. See the inside of the back cover for a list of all relevant web
The most current versions can be found on our website.
addresses.
Introduction 5 Connecting a computer 7 Required computer connections 7 Displaying a computer image 9 First-time projector use with Windows 98 10 Adjusting the image 12 Connecting a video device 13 Displaying a video image 14
Shutting down the projector 16
Troubleshooting your setup 16
Using the keypad buttons 25 Using the remote control 26 Using the LitePort player 27 Using the audio 28
Optimizing computer images 29 Presentation features 29 Optimizing video images 29 Customizing the projector 29
Using the menus 30 Picture menu 31 Settings menu 34
Maintenance 39 Cleaning the lens 39 Using the security lock 39 Replacing the projection lamp 40 Cleaning the lamp filter screens 42
Appendix 43 Accessories 43 Red LED behavior and projector errors 44 Projected image size 44

Do not place objects or people in the 2 foot (.6m) area along the side of the projector.
For ceiling mount applications, this area should be 5 feet (1.5m).
2 ft (.6m)
5 ft (1.5m)
small amount of mercury. Dispose of it as required by local, state or fed-
to intake or exhaust vents. Do not place the projector on a tablecloth or
placed in the surrounding area and thoroughly clean the area along all
sides of the projector. Wash hands after cleaning the area and handling
warranty. For complete details of the warranty, see the Warranty section at
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
the ruptured lamp. This product has a lamp which contains a very
eral ordinances and regulations. For more information see
other soft covering that may block the vents.
the end of this user's guide.
recommended.
off axis.
vents.



announcements, and registration incentives. See the inside of the back cover
XGA 1024x768 resolution. The projector is easy to connect, easy to use, and
easy to maintain. An Interactive Display on the top of the projector gives
*The lens cap tether ships in the Documentation Pack. Attach it to the lens cap and the projector if desired.
Your new digital projector provides computer and video inputs and has

Register your projector on our website to receive product updates,
you constant feedback on the status of the projector.
for the web address.



VESA in/ USB JPEG
JPEG images from your computer to the projector using a USB mass storage
Port onscreen menu to select display preferences and automatically display
Contact an authorized InFocus dealer or visit the website listed on the back
It also has an RS-232 serial connector for serial control. The Command Line
The projector also has a LitePortTM USB connector (Type A) and player for
connected. Use your own JPEGs from your digital camera, or convert your
JPEGs using LitePort Utility (included on the CD), which allows you to eas-
vice and Support section of our website for advanced specifications on the
USB device and JPEG files.) You can use the remote control to select which
JPEGs to view (page 27) or you can set up the LitePort player using the Lite-
JPEG (Joint Photographic Experts Group, .jpg, .jpe, or .jpeg) images. This
allows you to display any JPEG image automatically, without a computer
device and your images are ready to be displayed. (Please refer to the Ser-
LiteShow wireless adapter and software for cable-free digital projection.
ily generate the highest quality JPEG images possible. Then transfer the
files, such as Microsoft PowerPointTM, WordTM, or ExcelTM files, into
You can use the projector’s M1 connector along with the InFocus
Interface (CLI) specifications and commands are on our website.
The projector provides computer and video connectors:
inside cover of this User’s Guide for more information.
and advance your JPEGs (page 36).
Connector Panel




on the projector. Connect the blue end to the video port on your computer. If
Some Macintosh computers do not have a standard VESA-out video port.
If the supplied computer cable will not connect to your computer, purchase
To advance slides in a PowerPoint™ presentation using the remote, plug the
Connect the black end of the computer cable to the Computer 1 connector
you are using a desktop computer, you first need to disconnect the monitor
Connect the black power cable to the connector on the back of the projector
To have sound with your presentation, connect the audio cable to your com-
your computer. USB drivers must be installed to use the USB feature. For
USB connector on the computer cable into the USB mouse connector on
The Power LED on the projector’s keypad turns solid green.
puter and to the Audio In connector on the projector.
the appropriate adapter from your Apple reseller.
Connecting a computer
cable from the computer’s video port.
more information, see page 11.
and to your electrical outlet.



connect USB mass storage device
This connector can be used as monitor out or VESA in. The default is VESA
connecting an RS-232 cable to the projector’s Serial Control connector. Spe-
computer screen as well as on the projection screen, plug the monitor cable
to the black Computer 2 connector on the projector. This connector can be
If you prefer connecting your projector to your computer with an optional
cific RS-232 commands can be found in the Service and Support section of
You can play JPEGs using the LitePort USB connector and LitePort player.
change this option in the menu to use monitor out. See page 34 to switch
puter, and connect the other end of the cable to the blue Computer 2 con-
You can control the projector from an LCD control panel or computer by
You need a USB mass storage device to use this connector. See page 27 for
If you are using a desktop computer and want to see the image on your
VESA cable, connect one end of the cable to the VESA port on your com-
used as monitor out or VESA in. The default is VESA in, so you must
between the two functions.
nector on the projector.
our website.
details.
in.
connect monitor cable · connect VESA cable · connect RS-232 cable



activate laptop’s external port
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD
The LED flashes green and the fans start to run. When the lamp comes on,
minute for the image to achieve full brightness. The Interactive Display on
The computer’s image should appear on the projection screen. If it doesn’t,
the startup screen is displayed and the LED is steady green. It can take a
labeled function key simultaneously. Refer to your laptop’s documenta-
key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
Press the Power button on the top of the projector or the remote.
? No computer image? Try pressing the Auto Image
Make sure your laptop’s external video port is active.
press the Source button on the projector’s keypad.
? No startup screen? Get help on page 17.
button on the keypad. Get help on page 17.
tion to learn your laptop’s key combination.
the projector indicates the startup status.
Turn on your computer.
Remove the lens cap.
press Power button · turn on computer · remove lens cap





The first time you connect a computer running Windows 98 to the projector,
locates the driver. If this driver has been removed, reload the driver using
If you are running Windows 2000, Windows ME, or Window XP, skip these
New Hardware Wizard appears. Follow these instructions to use the Wiz-
d When Windows finds the driver, you are ready to install it. Click Next.
the computer recognizes the projector as “new hardware” and the Add
c Uncheck any checked boxes, then click Next. Windows automatically
ard to load the correct driver (which was installed with your Windows
b Make sure “Search for the best driver” is selected, then click Next.
steps and go to “Adjusting the image” on page 12.
a Click Next to begin searching for the driver.
your Windows operating system CD.
operating system).
a · b · d

appears again. Drivers must be installed to use the USB functionality.
Skip this page if you did not connect the USB portion of the M1 com-
The first time it detects a USB Human Interface Device (for the key-
The second time it detects a USB Human Interface Device (for the
For Windows 2000, Windows ME, and Windows XP:
For Windows 98:
board).
mouse).
puter cable



adjust Contrast or Brightness
adjust zoom and focus
Adjust the zoom or focus rings by rotating them until the desired image size
upper part of the image, and press the lower Keystone button to reduce the
The projector has an Auto Keystone option that is turned on by default. But
You can also adjust the keystone via the menus, or turn off Auto Keystone.
Adjust the height of the projector, if necessary, by pressing the release but-
Rotate the leveling foot (located at the bottom back right corner), if neces-
Position the projector the desired distance from the screen at a 90 degree
if the image is not square, adjust the vertical digital keystone by using the
buttons on the keypad. Press the upper Keystone button to reduce the
See page 44 for a table listing screen sizes and distances.
Adjust the Contrast or Brightness in the Picture menu.
See page 30 for help with the menus.
ton to extend the elevator foot.
and focus are produced.
angle to the screen.
lower part.
See page 31.
sary.




connect S-video and audio cables
connect video and audio cables
device and into the S-Video 1 connector on the projector. Use the audio con-
Plug the video cable into the video-out connector on the video device. Plug
the other yellow connector into the yellow Video 2 connector on the projec-
nector on the video device and plug the red connector into the right audio
Plug the audio cable into the other end of the audio cable adapter and into
Connect the black power cable to the connector on the back of the projector
Plug the white connector of the audio adapter into the left audio out con-
To connect a progressive scan EDTV or HD source, use the Component to
If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video
the audio in connector on the projector.
out connector on the video device.
nectors as described directly above.
Optional video connections
M1 adapter (sold separately).
and to your electrical outlet.
tor.
connect power cable



turn on video device
angle to the screen. See page 44 for a table listing screen sizes and distances
The LED flashes green and the fans start to run. When the lamp comes on,
minute for the image to achieve full brightness. The Interactive Display on
Adjust the height of the projector by pressing the release button to extend
the startup screen is displayed and the LED is steady green. It can take a
Position the projector the desired distance from the screen at a 90 degree
The video device’s image should appear on the projection screen. If it
Press the Power button on the top of the projector or the remote.
the elevator foot. Rotate the leveling foot, if necessary.
doesn’t, press the Source button on the keypad.
? No startup screen? Get help on page 16.
the projector indicates the startup status.
Plug in and turn on the video device.
Remove the lens cap.
to the screen.



adjust zoom and focus
Adjust the zoom or focus rings by rotating them until the desired image size
Press the upper Keystone button to reduce the upper part of the image, and
If the image is not square, adjust the vertical keystone using the buttons on
You can also adjust the keystone via the menus, or set the projector to auto-
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.
press the lower Keystone button to reduce the lower part.
Adjust the volume on the keypad or remote.
matically adjust the keystone. See page 31.
See page 30 for help with the menus.
and focus are produced.
the keypad.
adjust Picture menu · adjust keystone · adjust volume

(page 26). If it does not, troubleshoot the setup. The Interactive Display and
The following tables show common problems. In some cases, more than one
LED on top of the projector indicate the state of the projector and can help
solid green The projector is plugged in, or the projec-
been turned off and the fans have stopped.
sented. When the problem is solved, you can skip the additional solutions.
blinking green The power button has been pressed and
the software is initializing, or the projec-
A fan or lamp failure has occurred. Make
page 23). Turn off the projector and wait
lamp timer. Contact Technical Support if
tor has been powered on and the soft-
ware has initialized. The projector has
tor is powering down and the fans are
one minute, then turn the projector on
appears, replace the lamp and reset the
possible solution is provided. Try the solutions in the order they are pre-
If your image appears correctly on the screen, skip to the next section
again. If the Replace Lamp message
sure the vents aren’t blocked (see
running to cool the lamp.
the problem persists.
Technical Support.
see page 44 for more information
you troubleshoot.
keypad button is pressed. The Interactive Display on the projector indicates
options for the Screen Save feature. They range from five minutes to 30 min-
To turn off the projector, press the Power button and verify that you want to
lights green and the fans stop. Unplug the power cable to completely power
detected for 30 minutes. This blank screen helps preserve the life of the pro-
Screen Save in the Settings>System menu. See page 35. There are six time
lamp off after no signal is detected for 20 minutes. After 10 additional min-
passed. When Power Save is enabled, Screen Save is disabled. See page 35.
turn the projector off by pressing the Power button again within 3 seconds.
fans continue to run to cool the lamp. When the lamp has cooled, the LED
jector. The image returns when an active source is detected or a remote or
You can cancel the shutdown by not pressing the Power button a second
time. The lamp turns off and the LED blinks green for 1 minute while the
You can make the blank screen appear after five minutes by turning on
The projector also has a Power Save feature that automatically turns the
received before the projector powers down, the image is displayed. You
must press the Power button to display an image after 30 minutes have
The projector automatically blanks the screen after no active source is
utes with no signal, the projector powers down. If an active signal is
utes with five minute intervals.
Turning off the projector
the shutdown status.
off the projector.


No startup screen Plug power cable in, press Power button.
Only startup screen appears
Source Troubleshooting



range” Adjust computer refresh rate in Control
No computer image, just the words “Signal out of



Desktop icons Disable “Extend my Windows Desktop” in
Only my laptop’s background appears, not the
A A A
Uncheck this · option, then · click Apply


Remote control not advancing PowerPoint slides Connect USB cable (page 7) then load USB
presentation does not play on the screen Turn off the internal LCD display on your
The video embedded in my PowerPoint

Image not square Adjust keystone on keypad or Picture menu Square image

Image not sharp Adjust the focus lens or Sharpness in the
Image does not fit 16:9 screen Change aspect ratio to 16:9 in
Problem Solution Result · Projector troubleshooting

A B
A B
Image reversed left to right Turn off Rear in Settings>System menu Correct image
Settings>System menu Correct image
brightness, contrast in the menus Correct image
Projected colors don’t match source Adjust color, tint, color temperature,


Image upside down Turn off Auto Ceiling or Ceiling in

A B
A

projector to cool for one minute Unplug projector; wait one minute; plug in


Image not centered on screen Move projector, adjust zoom, adjust height Correct image

Lamp won’t turn on, LED blinking red (page 16) Make sure vents aren’t blocked; allow
blinks · red

Lamp won’t turn on, LED blinking red (page 16) Lamp must be replaced (page 40) Lamp turns on
having a professional packaging company pack the unit. Please insure your
If you need assistance, visit the Service and Support section of our website
This product is backed by a limited warranty. An extended warranty plan
repair, we recommend shipping the unit in its original packing material, or
or call us. See the inside of the back cover for a list of all relevant web
may be purchased from your dealer. When sending the projector in for
shipment for its full value.
addresses.
blinks · red

Most buttons are described in detail in other sections, but here is an over-
up/down arrows–navigates to and adjusts settings in the menus (page 30).
keystone–vertical keystone adjusts the squareness of the image (page 12).
presets–cycles through the available preset settings (page 32).
You can also adjust the keystone via the menus. See page 31.
power–turns the projector on (page 9) and off (page 16).
select–confirms choices made in the menus (page 30).
auto image–resets the projector to the source.
menu–opens the on-screen menus (page 30).
source–changes the active source.
volume–adjusts sound (page 28).
view of their functions:
menu navigation buttons

tion of the M1 computer cable is connected and the correct drivers are
not dead. The LED at the top of the remote lights when any button is
previous button next button
puter, and are within the remote range of 30 feet (9.14m).
pressed when the battery power is adequate.
installed.
Previous and Next buttons allow you to navigate through your PowerPoint
computer cable to your computer to use these buttons. When you do this for
page 16 for shutdown info), Volume and Mute buttons to control the sound,
to display a blank screen instead of the current slide (you can choose which
The remote uses two (2) provided AA batteries. They are easily installed by
sliding the cover off the remote’s back, aligning the + and - ends of the bat-
To operate, point the remote at the projection screen or at the projector (not
at the computer). The range of optimum operation is about 30 feet (9.14m).
presentation while in Slide Show mode. Connect the USB connector on the
the first time, the Add New Hardware wizard may appear. See page 10 for
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
Two presentation-specific features are also provided. Use the Blank button
color is displayed, see page 37); use the Effect button to invoke a user-defin-
able action, such as freeze or aspect ratio (see page 38 to learn to program
The remote also has a Power button to turn the projector on and off (see
adjust values in the menus. See page 30 for more info on the menus.
teries, sliding them into place, and then replacing the cover.
and a Source button to switch between sources.
details on loading the correct USB drivers.
this button).
navigation · buttons

thumbnail on the screen and pressing Next or Down arrow. You are looped
In File View mode, pressing Next (or Down) places the selection box around
the next JPEG file, pressing Previous (or Up) places the selection box around
Folder View mode. Eight file thumbnails can be displayed on the screen at a
by navigating to the last thumbnail on the screen and pressing Next. You are
file, pressing Previous (or Up) goes to the previous JPEG file, pressing Select
returns File View mode. To rotate the JPEG 90 degrees clockwise, select Lite-
the previous JPEG, pressing Select selects the current JPEG and enters Full
time. If your folder contains more than 8 folders, you can navigate to them
Screen mode, or, if the “return to folders” arrow is highlighted, returns to
In Full Screen mode, pressing Next (or Down) advances to the next JPEG
Port Rotate in the Effect menu (see page 38) then press the Effect button.
6 7 File 8 (press Next
to access File 9)
looped back to File 1 when you reach the end of the file list.
back to Folder 1 when you reach the end of the folder list.
Table 2: Folder View navigation
Table 3: File View navigation
Folders arrow File 1 2
Press Select to return to File View mode.
Return to
computer connected. Use your own JPEGs from your digital camera, or con-
display images at 960x720 resolution, so for best results, create JPEGs at this
jector using a USB mass storage device and your images are ready to be dis-
played. You can use the remote control to select which JPEGs to view or you
display preferences and automatically display and advance your JPEGs. See
first JPEG alphabetically in that folder. Folders are sorted alphabetically
enters Full Screen mode if Auto Play is checked (the default setting) and the
the white selection box around the next folder, pressing the Previous button
tains more than 9 folders, you can navigate to them by navigating to the last
vert your files, such as PowerPoint or Word files, into JPEGs using LitePort
Utility (included on the CD). LitePort Utility allows you to easily generate
resolution). Then transfer the JPEG images from your computer to the pro-
based on the name of the actual directory with no regard to the file sys-
The remote and keypad buttons interact with the player differently in each
AutoPlay folder contains a JPEG or it enters Folder View if Auto Play is not
In Folder View mode, pressing the Next button (or the Down arrow) places
(or the Up arrow) places the selection box around the previous folder, press-
ing Select selects the current folder and enters File View mode. Nine folder
thumbnails can be displayed on the screen at a time. If your USB drive con-
the highest quality JPEG images possible. (LitePort player is optimized to
can set up the LitePort player using the LitePort onscreen menu to select
folder that contains a valid JPEG. The thumbnail for that folder is the
mode. When you insert a USB device in the LitePort connector, the player
checked. The AutoPlay folder is automatically created by LitePort Utility.
LitePort allows you to display any JPEG image automatically, without a
When active, the player can be in one of three modes:
See its online help for details.
tem path to the folder.
folder.
page 36.

To play sound from the projector, connect your source to the Audio In con-
To adjust the balance or turn off the projector’s chime, use the Audio menu
power source by plugging a speaker cable into the projector’s Audio Out
The projector can be attached to external speakers that have their own
To adjust the volume, use the buttons on the keypad or remote.
To mute the sound, press the Mute button on the remote.
If there is no sound, check the following:
on the keypad or remote.
nector on the projector.
(see page 34).
connector.

After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general informa-
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
You can customize the projector for your specific setup and needs. See
page 34 to page 39 for details on these features.
Optimizing video images
tion on using the menus, see page 30.
input source. See page 31.
tings>System menu.
menu. See page 31.
power-up.
page 33.
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For gen-
save the settings using Presets. This allows you to quickly recall these
Aspect Ratio, Source, Auto Image, Freeze, About, and LitePort Rotate.
ful if you want to make changes on your computer without your audi-
matically shut down the projector after several minutes of inactivity or
Several features are provided to make giving presentations easier. The fol-
lowing is an overview, details are found in the menu section on page 30.
key. The default effect is About. You can select from Blank, Mute,
display a blank screen. This helps preserve lamp life. See page 35.
screen to a black, white, or blue screen. See page 37.
eral information on using the menus, see page 30.
instead of the active source. See page 37.
settings later. See page 32.
See page 38 for details.
Advanced menu.
ence seeing them.
menu.





tons, or turn the feature on or off using check boxes. Press Select to confirm
Dots appear before the menu name. The number of dots indicate the menu’s
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to high-
level, ranging from one (the Main menu) to four (the most nested menus).
nected. For example, Sharpness is only available for video sources and will
grayed out when they are not available. For example, Brightness is grayed
To open the menus, press the Menu button on the keypad or remote. (The
down arrow buttons to adjust the value, select an option using radio but-
adjustments are complete, navigate to Exit, then press Select to go to the
To change a menu setting, highlight it, press Select, then use the up and
your changes. Use the arrows to navigate to another setting. When your
be hidden when a computer source is active. Other menu items may be
previous menu; press the Menu button at any time to close the menus.
Certain menu items may be grayed out until a particular source is con-
light the desired submenu, then press the Select button.
The menus are grouped by usage:
out until an image is active.
projector and source.
changed often.

increasing keystone decreasing keystone



TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are
To adjust the following six settings, highlight the setting, press Select, use
also adjust keystone from the keypad. If you want the projector to automat-
ically adjust the keystone, check the Auto Keystone check box. If you then
jector is in Ceiling Mount mode, Auto Keystone is turned off. You can do a
“one-time” automatic keystone adjustment by pressing both Keystone but-
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
the up and down arrows to adjust the values, then press select to confirm
manually adjust the keystone, Auto Keystone is turned off. When the pro-
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or down to fill the display area.
parts of the picture and changes the amount of black and white in the
The aspect ratio selection is saved for each source.
Brightness: changes the intensity of the image.
black and white to fully saturated color.
tons on the keypad at the same time.
the changes.
image.
image.
Aspect Ratio


puter presentations, photographs, and film images. You can use the preset
as a starting point, then further customize the settings for each source. To
There are also three user-definable presets. To set a preset for the current
source, adjust the image, then choose Save User 1, 2, or 3. You can recall
these settings in the future by selecting the appropriate user presets.
restore the factory default settings, choose Factory Reset in the Set-
tings>Service menu.
Presets


Color Space Color Temperature Color Control




When Auto is selected, the projector automatically determines the standard.
attempts to pick the video standard automatically based on the input signal
it receives. (The video standard options may vary depending on your region
To choose a different setting, turn off Auto, then choose RGB for computer
colors may not look right or the image may appear “torn.” If this happens,
manually select a video standard by selecting NTSC, PAL, or SECAM from
of the world.) If the projector is unable to detect the correct standard, the
hardware device, such as a DVD player, is not syncing properly with the
select a color space that has been specifically tuned for the video input.
Overscan: (video sources only) removes noise around the video image.
The following 4 options are for computer and component sources only.
Horizontal/Vertical Position: adjusts the position of a computer source.
the image. It increases the brightness of whites that are near 100%.
sources, choose either REC709 or REC601 for component sources.
color, press Select, then use the arrows to adjust the value.
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
projector, select this option to help it sync.
image. Select a sharpness setting.
the Video Standard menu.
value.
Sharpness · Advanced · Video Standard





the image upside down. This is On by default. When in Ceiling mode, Auto
goes into the startup state after the projector is powered on. This allows con-
defaults to the source selected in Power-up Source. If no source is found, a
determines which source the projector defaults to at startup. If no signal is
present, the projector checks the sources in order until a source is found or
when checked. When it is unchecked, this connector acts as a VESA input.
nector to be a monitor loop through of the incoming Computer 1 signal
blank screen displays. When Autosource is checked, Power-up Source
Ceiling: turns the image upside down for ceiling-mounted projection.
when using the optional Integrator remote. Also allows selection of a
default Power-up Source and enables or disables Autosource.
trol of ceiling mounted projectors with a wall power switch.
lowers the fan speed, making the projector quieter.
checks first for active video during power-up.
“Mute”) in the lower-left corner of the screen.
tor’s startup Chime on and off.
Keystone is turned off.
until power down.
cent screen.


nals are detected for a preset number of minutes. The image returns when
an active source is detected or a remote or keypad button is pressed. Screen
for 20 minutes. After 10 additional minutes with no signal, the projector
powers down. If an active signal is received before the projector powers
Save is disabled when Power Save is enabled.
down, the image will be displayed.
mode.
Screen Save · System




cally makes the LitePort player the active source and displays, in Full Screen
mode, the first JPEG in the LitePort\AutoPlay folder on the USB drive. If no
be displayed and Folder View mode is entered. When this box is unchecked,
the folders on the USB drive, starting with the current folder and continuing
a different aspect ratio than the screen, the image will fit in width or height,
image. Click the check box to turn it on, then highlight Seconds and use the
This menu allows you to control the embedded LitePort player in your pro-
AutoPlay folder exists or the AutoPlay folder is empty, then no images will
you must manually choose the LitePort source using the remote’s computer
depending upon which is larger. Any empty space will be filled with black.
determine how long each image is displayed before advancing to the next
Up/Down arrows on the keypad or remote to increase or decrease the dis-
previous slide by pressing the Up arrow or ahead to the next slide quicker
by pressing the Down arrow. Press the Select button to stop Auto Advance
jector to display JPEGs stored on your USB mass storage device. You can
button or the source button on the keypad. This will display Folder View
selected folder are displayed, and these JPEGs play on a continuous loop.
play time. When playing images with this option, you can go back to the
Split Vertical In, Split Vertical Out, Horizontal Blinds, Vertical Blinds, Box
In, and Box Out. For a demonstration of these transitions, go to the Slide
also control the LitePort player with the remote or keypad. See page 27.
transitions. Select among None (no transition), Random, Wipe Up, Wipe
Down, Wipe Left, Wipe Right, Split Horizontal In, Split Horizontal Out,
mode. See page 27 for details on selecting images to display using the
in alphanumeric folder order. If it is unchecked, only the JPEGs in the
Show>Slide Transition menu in PowerPoint.
and return to File View mode.
remote or keypad.
Auto Advance · LitePort · Slide Transition



instead of the default screen at startup and when no source is detected.
Blank button on the remote.
Startup Logo · Blank Screen




enabled at a time. Highlight an effect and press Select to choose a different
this only after changing the lamp. It displays a confirmation dialog box.
the remote to quickly and easily use the effect. Only one effect can be
Aspect Ratio: sets the ratio of the image width to image height.
Service: to use these features, highlight them and press Select.
Auto Image: causes computer sources to be reacquired.
Service Code: only used by authorized service personnel.
Source: cycles through the available sources.
after displaying a confirmation dialog box.
Freeze: pauses the projected image.
About: displays the About menu.
Blank: shows an empty screen.
one. The default effect is About.
Mute: turns off all sound.
menus and messages.
LitePort.
Effect Key · Service · Language

with a soft dry cloth
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you don’t intend to use the projector immediately, replace the lens cap.
“Accessories” on page 43 for ordering information. Refer to the information
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
Avoid using an excessive amount of cleaner, and don’t apply the
The projector has a security lock for use with a cable lock system. See
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
that came with the lock for instructions on how to use it.
chemicals might scratch the lens.
Cleaning the lens
Maintenance


turn off and unplug

loosen the screw on lamp module
pry the lamp door off
lamp has been in use. Fifty hours before the specified end of the lamp’s life,
3 Turn the projector upside down and remove the lamp door by placing a flat-blade screwdriver into the space between the lamp door and the
The lamp hour timer in the About menu counts the number of hours the
the message “Replace lamp” briefly appears on the screen at each startup
and in the Interactive Display. After 50 additional hours, the lamp will no
longer light. You can order new lamp modules from your dealer. See
2 Wait 60 minutes to allow the projector to cool thoroughly.
1 Turn off the projector and unplug the power cable.
4 Loosen the captive screw on the lamp module.
projector and gently prying the door off.
“Accessories” on page 43 for information.
you replace the lamp.
sharpness.
wait 60 minutes · About menu · the projector

reset lamp time in Service menu

remove module using bail wire
after lamp replacement. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or fed-
9 Re-attach the lamp connector to the projector. Make sure the connector is fully inserted.
If the lamp timer has reached the maximum number of hours for the projec-
“LED behavior and meaning” on page 16). To reset the lamp timer, press the
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it. Before replacing a ruptured lamp, clean
the lamp compartment and dispose of cleaning materials. Wash hands
5 Detach the lamp connector from the projector by gently pulling the con- nector until it is disconnected from the projector.
7 Install the new lamp module, making sure that it is properly seated. Be careful not to touch the interior components of the projector.
12 Plug in the power cable then press the Power button to turn the projec- tor back on, then reset the lamp hour timer.
6 Carefully remove the lamp module by grasping and lifting the metal bail wire. Dispose of the lamp in an environmentally proper manner.
8 Snap the bail wire back into its flat position against the lamp module.
simultaneously for 10 seconds. You can also navigate to the Settings>Ser-
tor lamp, the LED on the projector’s keypad will show a lamp error (see
decrease volume button on the keypad and the increase volume button
eral ordinances and regulations. For more information see
vice menu and select Lamp Reset to reset the lamp timer.
10 Tighten the screw on the lamp module.
11 Replace the lamp door.
disconnect lamp connector

3 Before you replace the lamp, repeat the cleaning process on the screen in the lamp compartment in the projector.
In dirty or dusty environments, the dust filter screens on the lamp module
remove dust and dirt from the screens lowers the lamp operating tempera-
the screens every 250 hours. Lamp screen maintenance may need to occur
2 Examine the dust filter screens on each side of the lamp module. If nec- essary, use compressed or canned air to clean the screens. Then use a
high temperatures inside the lamp module. These high temperatures can
ture and prolongs lamp life. To maximize lamp life you will need to clean
4 Examine the dust filter screen on the lamp door. If necessary, use com- pressed or canned air to clean the screen.
more often than 250 hours depending on your installation/use environ-
cotton swab dipped in isopropyl alcohol to lightly wipe each screen.
After you've wiped each screen, blow away any remaining contami-
impact lamp performance and operating life. Routine maintenance to
1 Remove the lamp module. Refer to page 40 for instructions.
5 Replace the lamp module and lamp door.
nants.
ment.

IR Conductor + Remote Control HW-CONDUCTOR+
RF Presenter Remote Control HW-PRESENTER-RF
84” Diagonal Wall/Ceiling Mounted Screen HW-WALLSCR84
IR Presenter Remote Control HW-PRESENTER
60” Diagonal Screen (portable) HW-DLXSCRN
Optional Accessories Part Number
LiteShow Wireless Connection LP-LITESHOW
Shipping Case (ATA approved) CA-ATA-020
False Ceiling Plate for Projector Mount SP-LTMT-PLT
M1 to Component Adaptor SP-M1-ADPT
Replacement Lamp Module SP-LAMP-019
Projector Cable Lock System SP-LOCK-B
Organizer Carry Case CA-C230
DVI-D Cable 6 ft (1.8 m) SP-DVI-D
Audio/Video Cable, 30 ft (9m) SP-AV30
50” Diagonal Screen (portable) A650
Extension Arm for Projector Mount
(ship with the projector) Part Number
Color-coded Cable Ties, 3 set SP-CABLETIES
Video Cable 6 ft (1.8 m) 210-0176-xx
Audio Cable 6 ft (1.8 m) 210-0118-xx
Audio Cable Adapter 210-0177-xx
Lens Cap Tether 321-0192-xx
Quick Setup card 009-0911-xx
User’s Guide with CD 010-0549-xx
Computer Cable 6 ft (1.8 m) SP-DVI-A
Projection Lamp Module (included
Accessories

5/1.5 2.75/0.83 3.4/1.02 2.2/0.66 2.73/0.82 10/3 5.5/1.65 6.8/2.04 4.41/1.32 5.46/1.64 15/4.6 8.25/2.53 10.2/3.13 6.61/2.03 8.2/2.51 20/6.1 11/3.36 13.6/4.15 8.81/2.69 10.93/3.33 30/9.1 16.5/5.01 20.4/6.19 13.22/4.01 16.39/4.97 32.8/10 18.0/5.5 22.3/6.8 14.45/4.41 17.92/5.46
Table 5:
If the projector is not functioning properly and the red LED is blinking, con-
Five (5) blinks The projector is overheating. Check for a
between the blinking cycles. Visit our website for more details on the red
attempts. Check the lamp and lamp door
Replace the lamp. Contact Technical Sup-
port for repair if replacing the lamp does
Four (4) blinks The fan has failed. Contact Technical Sup-
sult Table 4 to determine a possible cause. There are two second pauses
Two (2) blinks The lamp counter hours have exceeded
Three (3) blinks The projector has shut down the lamp.
blocked air vent. Contact Technical Sup-
lamp life hours. Replace the lamp and
port for repair if clearing the air vents
One (1) blink The lamp won't strike after five (5)
LED error codes. See the inside back cover for contact information.
installations for loose connections.
reset the lamp hours counter.
does not solve the problem.
not solve the problem.
port for repair.





ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PUR-
ranty if the Product has been damaged due to abuse, misuse, neglect, smoke
erly use the Product in the application for which said Product was intended.
This Limited Warranty excludes Product cleaning, repair, or replacement of
unusual Product wear and is not considered normal use under the terms of
OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS.
CHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER.
InFocus shall have no further obligation under the foregoing Limited War-
and excludes normal wear. The Lamp Product Limited Warranty excludes
Remanufactured Products and Software Products are exempt from the fore-
Product Limited Warranty or Software Product Limited Warranty for appli-
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI-
exposure (cigarette or otherwise), accident, unusual physical or electrical
authorized agents, causes other than from ordinary use or failure to prop-
plastics due to cosmetic damage and damage as a result of normal wear.
The Accessory Product Limited Warranty covers the accessory item only
going Limited Warranty. Please refer to the appropriate Remanufactured
CABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND
LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS
Product repair outside of the terms of the Limited Warranty will be on a
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-
stress, unauthorized modifications (including use of an unauthorized
mount), tampering, alterations, or service other than by InFocus or its
time and materials basis. Prolonged Product “demonstration” causes
DISCLAIMER OF UNSTATED WARRANTIES
expected lamp degradation.
cable Warranty information.
MAY NOT APPLY TO YOU.
this Limited Warranty.
If the Product while subject to this Limited Warranty, is defective in material
equivalent or superior to new parts performance. Limited Warranty periods
Product purchase, the original installed lamp shall have a 90-day or 500
Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Cor-
within the Limited Warranty period and to repair or replace defective parts
with new parts or, at the option of InFocus, serviceable used parts that are
chase will have a 90-day or 500 hours usage Limited Warranty Period
Replacement lamps purchased after the time of Projector Product pur-
chase shall have a 90-day or 500 hours usage Limited Warranty Period
poration (“InFocus”) warrants that the Projector, Lamps and Accessories
(hereinafter collectively or individually referred to as “Product” as appro-
reseller will conform to InFocus’ specifications and be free from defects in
material or workmanship for the respective Limited Warranty period pro-
vided below. InFocus does not warrant that the Product will meet the spe-
or workmanship during the warranty period, then InFocus, at its option,
All exchanged parts and Products replaced under this Limited Warranty
will become property of InFocus. InFocus' sole obligation is to supply (or
from the date of replacement lamp purchase, whichever comes first.
Replacement Lamps purchased at the time of Projector Product pur-
priate) purchased from InFocus, an InFocus distributor, or an InFocus
pay for) all labor necessary to repair the Product found to be defective
hours usage Limited Warranty Period, whichever comes first.
from the date of installation, whichever comes first.
cific requirements of the end-user customer.
Two (2) years from date of purchase.
will REPAIR or REPLACE the Product.
of purchase.
are as follows:
Limited Warranty

No repair or replacement of Product or part thereof shall extend the Limited
NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF
Mandatory Arbitration – Any action, regardless of form, arising out of the
workmanship shall only be effective for a period of ninety (90) days follow-
THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND
Limitation on Bringing Action - No action, regardless of form, arising out
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITA-
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS
Warranty period as to the entire Product. Warranty on the repair part and
UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPE-
Governing Law - Any action, regardless of form, arising out of the agree-
YOU MAY ALSO HAVE OTHER RIGHTS, DEPENDING ON JURISDIC-
ing the repair or replacement of that part or the remaining period of the
WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN
STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING
of the agreement to purchase the Product may be brought by purchaser
agreement to purchase the Product is subject to mandatory arbitration.
LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE
ment to purchase the Product is governed by Oregon law.
more than one year after the cause of action has accrued.
Product Limited Warranty whichever is greater.
INFOCUS’ LIABILITY.
TION.
The Limited Warranty periods hereof commence on the date of purchase by
the end-user customer. These Limited Warranty provisions shall apply only
by InFocus will return the repaired/replaced Product freight prepaid to the
place of original purchase, to the manufacturer (Purchaser must bear all tax,
to the end-user purchaser (first person or entity that purchased a new Prod-
resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS
Any person exercising a claim under this Limited Warranty must establish
to the satisfaction of InFocus both the date of purchase and that the Product
During the Limited Warranty period, to exercise this Limited Warranty, the
1-503-685-8888 or visit www.infocus.com/service For Warranty service, the purchaser will be advised to return or deliver the
defective Product freight and all fees prepaid, to an InFocus Service Center
displayed on the outside of the shipping carton or a similar package afford-
ing an equal degree of protection. InFocus or the service facility authorized
Products returned for Warranty service must be accompanied by a written
uct for personal or business use and not for the purpose of distribution or
was purchased new. The sales receipt or invoice, showing the date of pur-
purchaser must first contact 1) InFocus, 2) a service facility authorized by
or to a service facility authorized by InFocus. When returning Product to
InFocus, a Service Request Number (SR #) is required and must be clearly
number of the Product. Upon request of InFocus Corporation or an autho-
rized repair center for InFocus, proof of legal import must accompany the
InFocus or 3) the place of original purchase. InFocus Customer Service –
warranty repair Product, otherwise the Product must be returned to the
(iii) provides the dealer’s name; and (iv) provides the model and serial
duty and freight), or the Purchaser must bear charges for the warranty
chase of the Product is the proof of the date of purchase.
To Be Eligible For Limited Warranty Coverage
SUCH CONSUMER RIGHTS.
To Obtain Warranty Service
purchaser.
repair.
Limited Warranty Period

In Asia: InFocus Systems Asia Pte Ltd. 238A Thomson Road #18-01/04 Novena Square Singapore 307684 Telephone: (65) 6334-9005 Fax: (65) 6333-4525
In Europe: InFocus International B.V. Strawinskylaan 585 1077 XX Amsterdam,The Netherlands Phone: +31 20 579 2000 Fax: +31 20 579 2999
InFocus Corporation 27700B SW Parkway Avenue Wilsonville, Oregon 97070-9215 1-800-294-6400 • 503-685-8888 Fax: 503-685-8887 http://www.infocus.com
Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| No startup screen | P R | p.17 | |
| No startup screen | p.17 | ||
| Image not square | Adjust keystone on keypad or Picture menu | p.21 | |
| Image not sharp A B | Adjust the focus lens or Sharpness in the Picture>Advanced menu | p.21 | |
| Image does not fit 16:9 screen | Change aspect ratio to 16:9 in Picture>Aspect ratio menu | p.21 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.