EN
InFocus logo
Official user manual

InFocus 5700

43 pages·2.9 MB·Projector·PDF·ENDEFRITNLJA
InFocus 5700
Table of Contents 26 sections Introduction · Positioning the projector · Video connections · Connecting a video device · … ShowHide
Page 1 of the InFocus 5700 user manual — EN 61000-3-2
Page 1 · click to enlarge
Page 1

and, if not installed and used in accordance with the instructions, may cause harmful

installation. This equipment generates, uses and can radiate radio frequency energy

Changes or modifications not expressly approved by InFocus Corporation can void

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

--Connect the equipment into an outlet on a circuit different from that to which the

turning the equipment off and on, the user is encouraged to try to correct the

interference to radio communications. However, there is no guarantee that

provide reasonable protection against harmful interference in a residential

--Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

--Increase the separation between the equipment and receiver.

interference by one or more of the following measures:

UL, CUL, TÜV, NOM, IRAM, GOST, CCC, MIC, C-Tick

the user's authority to operate the equipment.

--Reorient or relocate the receiving antenna.

receiver is connected.

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple

ManufacturerInFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon

We declare under our sole responsibility that the ScreenPlay 5700 projector conforms

Computer, Inc. IBM is a trademark or registered trademark of International Business

trademarks of Microsoft Corporation. Digital Light Processing is a trademark or reg-

marks or registered trademarks of Faroudja. InFocus and ScreenPlay are trademarks

Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered

istered trademark of Texas Instruments. Faroudja, DCDi, and TrueLife are trade-

97070 USA European OfficeStrawinskylaan 585, 1077 XX Amsterdam, The Netherlands

Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC

EMC Directive 89/336/EEC, Amended by 93/68/EEC

ENGLISH

or registered trademarks of InFocus Corporation.

to the following directives and norms:

SafetyEN 60950: 2000

EN 61000-3-2

EN 61000-3-3

EMC: EN 55022

EN 55024

Show 6 more labels / short text on this page
Agency Approvals · FCC Warning · Canada · Declaration of Conformity · Trademarks · May, 2003
Page 2 of the InFocus 5700 user manual — Table of Contents
Page 2 · click to enlarge
Page 2

For complete details on connecting and operating the projector, refer to this

User’s Guide. Electronic versions of this User’s Guide in multiple languages

The website also has technical specifications (an interactive image size cal-

block the vents. Vents are placed along the left and right sides of the projec-

tor, as well as across the front of the projector. Do not use a non-approved

ceiling mount. In the unlikely event of the lamp rupturing, discard any edi-

product data sheet), a web store to buy accessories, and a page for online

Do not place the projector on a tablecloth or other soft covering that may

culator, laptop activation commands, connector pin outs, a glossary, the

ble items placed in the surrounding area and thoroughly clean the area

Do not place objects in the areas along the side and in the front of the projector

are available on our website at www.infocushome.com/support.

2 ft (.6m)

along the sides and in the front of the projector.

2 ft (.6m) 2 ft (.6m)

registration.

Introduction 3 Positioning the projector 5 Video connections 6 Connecting a video device 7 Displaying a video image 8 Connecting a computer 10 Shutting down the projector 11 Troubleshooting your setup 11 Using the keypad buttons 18 Using the remote control 19 Optimizing video images 20 Customizing the projector 20 Using the menus 21 Picture menu 22 Settings menu 27 Maintenance 29 Cleaning the lens 29 Replacing the projection lamp 30 Appendix 32 Specifications 32 Accessories 32 Red LED behavior and projector errors 33 Projected image size 33 Source compatibility 34 Projector dimensions for ceiling mount installations 35 RS-232 terminal specifications 36

Table of Contents

Page 3 of the InFocus 5700 user manual — Included items
Page 3 · click to enlarge
Page 3

IR

InFocus 5700 — IR diagram (page 3)
Fig. 1
InFocus 5700 — IR diagram (page 3)
Fig. 2

Projector components and features

tion, featuring true Enhanced Definition 1024x576 resolution using the latest

colors and details the way the director intended. Whether you are watching

movies or High Definition broadcasts or playing the latest video game, you

Congratulations and thank you for your excellent choice of a superior digi-

DLP™ technology and new DCDi video processing from Faroudja™. Cali-

ScreenPlay 5700 sets the standard for Enhanced-Definition digital perfec-

brated to D65 color mastering standards, the ScreenPlay 5700 reproduces

tal image projection device. Your new ScreenPlay™ 5700 projector from

Register your projector online at www.infocus.com/service/register to

user’s guide, safety card

receive product updates, announcements, and registration incentives.

InFocus® is specifically designed for home cinema applications. The

SCART

will enjoy breathtaking image quality.

Introduction

Included items

Show 14 more labels / short text on this page
heat vent · I/O panel · remote · control · vent · cable cover · power · cable* · cable · *country-dependent · Online Registration · remote · projector · lens cap
Page 4 of the InFocus 5700 user manual — Connector Panel
Page 4 · click to enlarge
Page 4

to screen relay (see screen manufacturer

M1-DA vesa trigger 1 8 2 1

D5

D5

Y Y

3.5mm mono plug

Two 3.5 mm mini-jack triggers provide 12 volt current. Trigger 1 provides a

down; when you turn the projector off, the screen will return to the storage

position. Trigger 2 provides a 4:3 aspect trigger. When you select 4:3 in the

will be sent after a three second delay. Use this trigger for screens with 4:3

aspect curtains. When you switch back to 16:9 format, the curtains open to

It also has a mini-jack input for a Niles or Xantech-compatible IR repeater

and an RS-232 connector for serial control. The Command Line Interface

(CLI) specifications and commands are listed in the Appendix starting on

Aspect Ratio menu or from the Resize button on the remote, a 12v signal

constant output while the projector is on. If you connect your projection

screen to Trigger 1, when you turn on the projector the screen will move

For details on each connector type and their inputs, see page 34.

The projector provides eight discreet video connectors:

  • one VESA (HD, HD component, and computer)
  • one M1-DA (HD, DVI, and computer)
  • two component RCA
  • one composite RCA
  • one component D5

reveal the entire screen.

Connector Panel

  • two S-video

page 36.

Show 28 more labels / short text on this page
remote control · receiver (IR) · lock · 12v triggers · trigger 2 · video · s-video video · video · for details) · component · Pb Pb · Pr Pr · component · video · s-video · ground · component · connector · +12v · serial control · serial · IR input · screen trigger connection · IR in · video/computer · connector · power · 1 & 2
Page 5 of the InFocus 5700 user manual — Positioning the projector
Page 5 · click to enlarge
Page 5

3.3’ above lens

There are a number a factors to consider when determining where to set up

This means that if you have an image 10’ high, the bottom of the image will

your power outlets, and the distance between the projector and the rest of

(0.15m) from a wall or other objects. Place the projector at least 5.6 feet

If you install the projector on the ceiling, refer to the installation guide

authorized InFocus ceiling mount. The Ceiling Mount Kit is sold sepa-

The distance from the lens of the projector to the screen, the zoom set-

the projector, including the size and shape of your screen, the location of

that comes with the Ceiling Mount Kit for more information. To turn

the image upside down, see page 27. InFocus recommends use of an

ting, and the video format determine the size of the projected image.

Go to www.infocushome.com/support for a complete image size calcula-

The projector must be within 10 feet (3 m) of your power source. To

The image exits the projector at a given angle. This image offset is 133%.

1 Position the projector on a flat surface at a right angle to the screen.

ensure adequate cable access, place the projector at least 6 inches

For more information about projected image sizes, see page 33.

2 Position the projector the desired distance from the screen.

your equipment. Here are some general guidelines.

Positioning the projector

(1.7 m) from the projection screen.

be 3.3’ above the center of the lens.

rately, see page 32.

tor.

lens center · 10’ high image · bottom of image

Page 6 of the InFocus 5700 user manual — Video connections
Page 6 · click to enlarge
Page 6

M1-DA vesa trigger 1 8 2 1

D5

Y Y

M1-DA VESA

games, HDTV receivers, and TV tuners to the projector. (You cannot directly

company; the signal must pass through a tuner first. Examples of tuners are

You can connect VCRs, DVD players, camcorders, digital cameras, video

digital cable boxes, VCRs, digital video recorders, and satellite TV boxes.

connect the coaxial cable that enters your house from a cable or satellite

Input signalConnectorConnector label on projector Standard Broadcast TV (not HDTV), via cable, digital cable, satellite TV, DirectTVComponent video S-video Composite videoComponent 3, 6 S-video 4, 5 Video 7 HDTVComponent video VESA DVIComponent 3, 6 VESA 2 M1-DA 1 DVDComponent video S-video Composite videoComponent 3, 6 S-video 4, 5 Video 7 VCRComposite video S-video Component videoVideo 7 S-video 4, 5 Component 3, 6 Video CameraComposite video S-videoVideo 7 S-video 4, 5

Video connections

Show 18 more labels / short text on this page
trigger 2 · s-video video · video · component · Pb Pb · Pr Pr · component · video · s-video · component · serial control · IR in · Component 3, 6 · S-video 4, 5 · Video 7 · Component video · Composite video · S-video
Page 7 of the InFocus 5700 user manual — Connecting the power cable
Page 7 · click to enlarge
Page 7
InFocus 5700 — Connecting a video device diagram (page 7)
Fig. 3 · Connecting a video device

M1-DA vesa trigger 1 8 2 1

D5

M1-DA vesa trigger 1 8 2 1

M1-DA vesa trigger 1 8 2 1

Y Y

D5

D5

Y Y

Y Y

M1-DA vesa trigger 1 8 2 1

D5

Y Y

connect composite video cable

one. DVI video has the best quality, followed by Component video, S-video,

If the video device uses component cable connectors, plug the cable’s green

connectors into the green component-out connector on the video device and

into the green component connector (labeled “Y”) on the projector. Plug the

ite video cable’s yellow connector into the video-out connector on the video

device. Plug the other yellow connector into the yellow Video connector on

If the video device uses a DVI connector, plug an M1-D cable into the video-

out connector on the video device. Plug the other connector into the M1-DA

Connect the power cable to the connector on the back of the projector and to

component cable’s blue connectors into the blue component-out connector

on the video device and into the blue component connector (labeled “Pb”)

component-out connector on the video device and into the red component

S-video cable into the S-video connector on the video device and into the S-

If the video device uses a yellow composite video connector, plug a compos-

video-out connector on the video device. Plug the other connector into the

If your video device has more than one output, select the highest quality

on the projector. Plug the component cable’s red connectors into the red

If the video device uses a round, four-prong S-video connector, plug an

If the video device uses a VESA connector, plug a VESA cable into the

your electrical outlet. The Power LED on the keypad turns solid green.

Connecting a video device

connector (labeled “Pr”) on the projector.

VESA connector on the projector.

video connector on the projector.

Connecting the power cable

and then composite video.

connector on the projector.

the projector.

Show 41 more labels / short text on this page
trigger 2 · Pb Pb · video · Pr Pr · component · trigger 2 · trigger 2 · s-video · component · video · serial control · Pb Pb · Pr Pr · s-video · component · Pb Pb · video · Pr Pr · component · IR in · serial control · component · s-video · IR in · serial control · component · trigger 2 · IR in · video · Pb Pb · Pr Pr · component · s-video · component · serial control · IR in · connect component cable · connect S-video cable · connect M1-D cable · connect VESA cable · connect power cable
Page 8 of the InFocus 5700 user manual — Displaying a video image
Page 8 · click to enlarge
Page 8
InFocus 5700 — Displaying a video image diagram (page 8)
Fig. 4 · Displaying a video image

turn on video device

flashes green and the fans start to run. When the lamp comes on, the startup

An image from the video device should appear on the projection screen. If it

Adjust the height of the projector by pressing the release button to extend

Position the projector the desired distance from the screen at a 90 degree

The projector chimes if the chime feature is enabled (page 28). The LED

screen displays and the LED is steady green. It can take a minute for the

angle to the screen. See page 33 for a table listing screen projected image

the elevator foot. Rotate the leveling foot, if necessary.

Press the Power button on the top of the projector.

doesn’t, press the Source button on the keypad.

? No startup screen? Get help on page 12.

Displaying a video image

Plug in and turn on the video device.

image to achieve full brightness.

sizes and distances to the screen.

Remove the lens cap.

Show 8 more labels / short text on this page
leveling · rotate · foot elevator · remove lens cap · press Power · adjust distance · adjust height · foot
Page 9 of the InFocus 5700 user manual — Displaying a video image
Page 9 · click to enlarge
Page 9
InFocus 5700 — Displaying a video image diagram (page 9)
Fig. 5 · Displaying a video image

adjust zoom and focus

Adjust the zoom or focus rings by rotating them until the desired image size

tion of the image, and press the lower Keystone button to reduce the width

If the image is not square, adjust the keystone using the buttons on the key-

pad. Press the upper Keystone button to reduce the width of the upper por-

The Contrast, Brightness, Color, andTint are factory calibrated to D65 col-

ors, but you can adjust these settings in the Picture menu if necessary.

See page 21 for help with the menus.

and sharpness are produced.

of the lower portion.

Show 4 more labels / short text on this page
focus · zoom · adjust Picture menu · adjust keystone
Page 10 of the InFocus 5700 user manual — Connecting a computer
Page 10 · click to enlarge
Page 10
InFocus 5700 — Connecting a computer diagram (page 10)
Fig. 6 · Connecting a computer
InFocus 5700 — Connecting a computer diagram (page 10)
Fig. 7 · Connecting a computer
InFocus 5700 — Connecting a computer diagram (page 10)
Fig. 8 · Connecting a computer

M1-DA vesa trigger 1 8 2 1

D5

Y Y

Connect the power cable to the connector on the back of the projector and to

RS-232 commands can be found in the Appendix starting on page 37 and in

Connect either a VESA cable or M1 cable into the appropriate connector on

the projector. Connect the other end to the video port on your computer. If

you are using a desktop computer, you first need to disconnect the monitor

the Service and Support section of our website at www.infocushome.com/

You can control the projector from an LCD control panel or computer by

connecting an RS-232 cable to the projector’s Serial connector. Specific

The Power LED on the projector’s keypad turns solid green.

Turn on the projector, then your computer.

Connecting a computer

cable from the computer’s video port.

your electrical outlet.

support.

Show 12 more labels / short text on this page
trigger 2 · video · Pb Pb · Pr Pr · component · s-video · component · serial control · IR in · connect computer cable · connect RS-232 cable · connect power cable
Page 11 of the InFocus 5700 user manual — Shutting down the projector
Page 11 · click to enlarge
Page 11

The LED on top of the projector’s keypad indicates the state of the projector

solid green The projector is plugged in, or the projec-

tor has been turned on and the software

blinking green The Power button has been pressed and

the software is initializing, or the projec-

times) failure has occurred. Turn off the

projector and wait one minute, then turn

the projector on again. Also check for a

The following table shows some potential problems. In some cases, more

than one possible solution is provided. Try the solutions in the order they

has initialized. The projector has been

tor is powering down and the fans are

A fan (blinks 4 times) or lamp (blinks 3

blocked vent or a stopped fan (blinks 5

solid red An unidentifiable errorplease contact

are presented. When the problem is solved, you can skip the additional

If your image appears correctly on the screen, skip to the next section

turned off and the fans have stopped.

running to cool the lamp.

Table 2: LED behavior and meaning

Technical Support.

(page 18). If it does not, troubleshoot the setup.

Troubleshooting your setup

times).

The projector will not start up if the LED

is blinking red. You must correct the prob-

lem, disconnect and reconnect the power

See page 33 for more information on

and can help you troubleshoot.

cable, then power on the projector.

blinking red LEDs.

solutions.

cally turns the lamp off after no signals are detected for 20 minutes. After 10

signal is received before the projector powers down, the image is displayed.

You must press the Power button to display an image after 30 minutes have

To turn off the projector, press the Power button. The lamp turns off and the

cool the lamp. When the lamp has cooled, the LED lights green and the fans

additional minutes with no signal, the projector powers down. If an active

The projector has a Power Save feature in the System menu that automati-

LED blinks green for about one minute while the fans continue to run to

LED color/behaviorMeaning solid greenThe projector is plugged in, or the projector has been turned on and the software has initialized. The projector has been turned off and the fans have stopped. blinking greenThe Power button has been pressed and the software is initializing, or the projector is powering down and the fans are running to cool the lamp. blinking red The projector will not start up if the LED is blinking red. You must correct the problem, disconnect and reconnect the power cable, then power on the projector. See page 33 for more information on blinking red LEDs.A fan (blinks 4 times) or lamp (blinks 3 times) failure has occurred. Turn off the projector and wait one minute, then turn the projector on again. Also check for a blocked vent or a stopped fan (blinks 5 times). solid redAn unidentifiable error: please contact Technical Support.

stop. Unplug the power cable to completely power off the projector.

Shutting down the projector

Turning off the projector

passed.

LED color/behavior Meaning · blinking red · Power Save

Page 12 of the InFocus 5700 user manual — Shutting down the projector
Page 12 · click to enlarge
Page 12
InFocus 5700 — Shutting down the projector diagram (page 12)
Fig. 9 · Shutting down the projector
InFocus 5700 — Shutting down the projector diagram (page 12)
Fig. 10 · Shutting down the projector

No startup screen Plug power cable in and remove lens cap

ProblemSolutionResult No startup screenPlug power cable in and remove lens cap press Power buttonCorrect image S c re e n P la y
Page 13 of the InFocus 5700 user manual — A B
Page 13 · click to enlarge
Page 13

A B

Image not square Adjust keystone on keypad Square image

Picture>Aspect ratio menu Correct image

Edges of image distorted Turn Overscan on in the Picture menu Correct image

InFocus 5700 — A B diagram (page 13)
Fig. 11

Change aspect ratio to 16:9 in

A B

Image does not fit 16:9 screen

Page 14 of the InFocus 5700 user manual — A B
Page 14 · click to enlarge
Page 14

COLOR

A B

A B

Image reversed left to right Turn off Rear in Settings>System menu Correct image

2. Pick another gamma setting 3. Pick another color space Correct image

Image upside down Turn off Ceiling in Settings>System menu Correct image

InFocus 5700 — COLOR diagram (page 14)
Fig. 12
1. Adjust color, tint, color temperature, brightness, or contrast in the menus.
InFocus 5700 — COLOR diagram (page 14)
Fig. 13
2. Colors are washed out or too deep 3. Image from component source appears greenish

COLOR

1. Projected colors don’t match source

A B

A

Page 15 of the InFocus 5700 user manual — projector and turn it on: lamp lights AABB
Page 15 · click to enlarge
Page 15

projector to cool for one minute Unplug projector; wait one minute; plug in

projector and turn it on: lamp lights AABB

A B

Picture>Advanced menu Correct image

Lamp won’t turn on, LED blinking red (page 11) Make sure vents aren’t blocked; allow

InFocus 5700 — projector and turn it on: lamp lights AABB diagram (page 15)
Fig. 14 · projector and turn it on: lamp lights AABB

Video image “torn” and fragmented Change Video Standard in

ScreenPlay · blinks · red

Page 16 of the InFocus 5700 user manual — A
Page 16 · click to enlarge
Page 16
InFocus 5700 — Shutting down the projector diagram (page 16)
Fig. 15 · Shutting down the projector
InFocus 5700 — Shutting down the projector diagram (page 16)
Fig. 16 · Shutting down the projector

range” Adjust computer refresh rate in Control

Only startup screen appears Press the Source button

No computer image, just the words “Signal out of

A

A

Show 7 more labels / short text on this page
or restart · system) · laptop · ScreenPlay · Signal out of · range · Computer-specific troubleshooting
Page 17 of the InFocus 5700 user manual — Still having problems?
Page 17 · click to enlarge
Page 17

projector in for repair, we recommend shipping the unit in its original pack-

with all accessories for shipping. An optional ATA shipping case is available

This product is backed by a limited two-year warranty. When sending the

for purchase that provides adequate protection for shipping. Please insure

ing material, or having a professional packaging company pack the unit

Image clear and not cropped

A

your shipment for its full value.

Image fuzzy or cropped Set your computer’s display resolution to

InFocus 5700 — A diagram (page 17)
Fig. 17

the native resolution of the projector

1-800-799-9911. Support is free between 6 a.m. and 6 p.m. PST, Monday through Friday. Support is available in North America after hours and

If you need assistance, call InFocus Customer Service directly at

In Europe, call InFocus in The Netherlands at (31) 20 579 2820.

In Asia, call InFocus in Singapore at (65) 6334-9005.

Or, send us an e-mail at techsupport@infocus.com.

weekends for a fee at 1-888-592-6800.

A A A

Still having problems?

Show 8 more labels / short text on this page
Panel>Display>Settings tab, select · (Start>Settings>Control · or turn-on dual- · disable laptop · For a laptop, · display mode · 1024x576) · monitor
Page 18 of the InFocus 5700 user manual — Using the keypad buttons
Page 18 · click to enlarge
Page 18
InFocus 5700 — Using the keypad buttons diagram (page 18)
Fig. 18 · Using the keypad buttons

Up/down arrows–navigates to and adjusts settings in the menus (page 21).

Most buttons are described in detail in other sections, but here is an over-

Presets–cycles through the 3 available user preset settings (page 24).

Keystone–adjusts squareness of the image (page 9 and page 22).

Power–turns the projector on (page 8) and off (page 8).

Select–confirms choices made in the menus (page 21).

Brightness–adjusts intensity of the image (page 22).

Auto image–resynchs the projector to the source.

Menu–opens the on-screen menus (page 21).

Source–changes the active source (page 27).

Resize–changes the aspect ratio (page 22).

Using the keypad buttons

view of their functions:

menu navigation buttons

Page 19 of the InFocus 5700 user manual — Troubleshooting the remote
Page 19 · click to enlarge
Page 19
InFocus 5700 — Using the remote control diagram (page 19)
Fig. 19 · Using the remote control
  • Make sure you’re pointing the remote at the projector or the screen, not

at the video device or the computer, and are within the remote range of

The remote uses two (2) provided AAA batteries. They are easily installed

To operate, point the remote at the projection screen or at the projector (not

Press the remote’s Menu button to open the projector’s menu system. Use

the arrow buttons to navigate, and the Select button to select features and

  • Blank button to display a blank screen instead of the current image (to
  • Source buttons to switch among sources (to assign a particular source
  • Make sure the batteries are installed in the proper orientation and are

by sliding the cover off the remote’s back, aligning the + and - ends of the

at the video device or computer). The range of optimum operation is 0 to

  • Power button to turn the projector on and off (see page 11 for shut-

adjust values in the menus. See page 21 for more info on the menus.

  • Overscan button to remove noise in a video image (page 24)

batteries, sliding them into place, and then replacing the cover.

  • backlight button to light the remote’s buttons in the dark
  • Auto Image button to resynch the projector to the source
  • Resize button to change the Aspect Ratio (see page 22)
  • Brightness and Contrast buttons to adjust the image
  • Preset button to restore stored settings (see page 24)

to a source button, see page 27) and a source toggle

change the color of the screen, see page 28)

Using the remote control

Troubleshooting the remote

The remote also has:

30 feet (9.14m).

30 feet (9.14m).

not dead.

backlight button · navigation buttons · down info)

Page 20 of the InFocus 5700 user manual — Optimizing video images
Page 20 · click to enlarge
Page 20
  • Specify blank screen colors and startup logos. Make the menus translu-
  • For rear projection, turn Rear mode on in the Settings>System menu.
  • Turn the projector’s display messages and power-on chime on and off.

You can customize the projector for your specific setup and needs. See

  • For ceiling mounted projection, turn Ceiling mode on in the Set-

page 27 to page 29 for details on these features.

Customizing the projector

  • Turn on power saving features.
  • Specify the menu language.

tings>System menu.

cent.

After the video device is connected properly and the image is on the screen,

and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your

  • Turn overscan on to remove noise around the video image. See page 24.

you can optimize the image using the onscreen menus. For general informa-

  • Change the Aspect ratio. Aspect ratio is the ratio of the image width to

image height. TV screens are usually 1.33:1, also known as 4:3. HDTV

input source in the menus, or press the Resize button on the remote to

  • Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
  • Select a different Color Temperature or use the Color Control to adjust
  • Select a different Video Standard. Auto tries to determine the standard
  • Tune colors to your specifications using Blue Only, Color Wheel Index,
  • Make sure your DVD player is set for a 16:9 television. See your DVD
  • Fine tune component inputs using the TrueLife™ adjustments. See

of the incoming video. Select a different standard if necessary. See

the gain and offset of the red, green, and blue color. See page 26.

  • Choose High Power to maximize the light output. See page 27.
  • Select a specific Color Space or Gamma. See page 26.

cycle through the options. See page 22.

player’s user’s guide for instructions.

Optimizing video images

and ADC Calibration. See page 29.

tion on using the menus, see page 21.

menu. See page 22.

page 26.

page 25.

Page 21 of the InFocus 5700 user manual — Using the menus
Page 21 · click to enlarge
Page 21
InFocus 5700 — Using the menus diagram (page 21)
Fig. 20 · Using the menus
InFocus 5700 — Using the menus diagram (page 21)
Fig. 21 · Using the menus
InFocus 5700 — Using the menus diagram (page 21)
Fig. 22 · Using the menus

tons, or turn the feature on or off using check boxes. Press Select to confirm

Dots appear before the menu name. The number of dots indicate the menu’s

  • The About menu provides a read-only display of information about the

menus automatically close after 60 seconds if no buttons are pressed.) The

Main menu appears. Use the arrow buttons to move up and down to high-

adjustments are complete, navigate to Exit, then press Select to navigate to

the previous menu; press the Menu button at any time to close the menus.

level, ranging from one (the Main menu) to four (the most nested menus).

For example, Tint is only available for NTSC video sources and will be hid-

when they are not available. For example, Brightness is grayed out until an

To open the menus, press the menu button on the keypad or remote. (The

down arrow buttons to adjust the value, select an option using radio but-

Certain menu items may be hidden until a particular source is connected.

den when other sources are active. Other menu items may be grayed out

To change a menu setting, highlight it, press Select, then use the up and

your changes. Use the arrows to navigate to another setting. When your

  • The Settings menu provides set-up type adjustments that are not

light the desired submenu, then press the Select button.

  • The Picture menu provides image adjustments.

The menus are grouped by usage:

Using the menus

projector and source.

changed often.

image is active.

Show 8 more labels / short text on this page
Keypad navigation · Settings menu · buttons Main menu · Menu · button · Dots · About menu · Picture menu
Page 22 of the InFocus 5700 user manual — Picture menu
Page 22 · click to enlarge
Page 22

increasing keystone decreasing keystone

Keystoneadjusts the image vertically and makes a squarer image. You can
Contrastcontrols the degree of difference between the lightest and darkest

TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are

approximately 640x480, 4x3 images will always be smaller than the dis-

play and will be centered in the display. Computer images 1024x768 or

To adjust the following five settings, highlight the setting, press Select, use

Color(video sources only) adjusts a video image from black and white to
Tint(NTSC video sources only) adjusts the red-green color balance in the

Aspect Ratio: Aspect ratio is the ratio of the image width to image height.

1.78:1, or 16:9. You can choose Native, 4:3, 16:9, Letterbox, or Natural Wide. The default is 16:9. The goal is to show the most detail on the screen while

preserving the ratio of width to height. The native resolution of the projec-

smaller will also be centered in the display. If a 16x9 video source or a

the up and down arrows to adjust the values, then press select to confirm

Brightnesschanges the intensity of the image. You can also adjust bright-

tor is 1024x576. Use Native, 4:3 or Naural Wide for 4:3 input sources; use

Native, 16:9 or Letterbox for 16:9 input. Pressing the Resize button on the

Nativethis mode bypasses the internal scaler, displaying the image

1280x1024 or larger computer source is viewed, it will display up to 1024 pixels and 576 lines from the center of the input.

the changes. All menu defaults are listed in a table starting on page 37.

parts of the picture and changes the amount of black and white in the

Since the native resolution is 1024x576 and 4x3 video images are

also adjust keystone from the keypad.

remote cycles through these options.

ness from the keypad.

with no resizing.

fully saturated color.

Picture menu

image.

image.

Aspect ratio

Page 23 of the InFocus 5700 user manual — Picture menu
Page 23 · click to enlarge
Page 23

letterbox image input 16:9 image fills 16:9 screen

4:3 image input 4:3 image on 16:9 screen

4:3 image fills 16:9 screen

16:9 image input 16:9 image

4:3 image input

4:3 aspect ratio

16:9 aspect ratio

16:9: the default is 16:9, which preserves the 16:9 aspect ratio and is designed to be used with content that is Enhanced for Widescreen TVs.

Letterboxpreserves the 16:9 aspect ratio. If you have a 16:9 source and

4:3: resizes the image from its original version to fit a standard 4:3 aspect ratio screen. If you have a 4:3 source on a 16:9 screen, the image

is placed in a 16:9 space, so black bars appear at the sides of the image.

screen. The center two-thirds of the image is unchanged; the edges of

Natural Widethis mode stretches a 4:3 image to fill the entire 16:9

screen, the image fills the screen. If your source is letterboxed, the

image expanded to fill the screen.

the image are stretched.

Show 8 more labels / short text on this page
black bars · black bars · black bars · black bars · 3 letterbox · aspect ratio · natural wide · aspect ratio
Page 24 of the InFocus 5700 user manual — Picture menu
Page 24 · click to enlarge
Page 24
InFocus 5700 — Picture menu diagram (page 24)
Fig. 23 · Picture menu
InFocus 5700 — Picture menu diagram (page 24)
Fig. 24 · Picture menu
InFocus 5700 — Picture menu diagram (page 24)
Fig. 25 · Picture menu
InFocus 5700 — Picture menu diagram (page 24)
Fig. 26 · Picture menu

restored later. To restore the factory default settings, choose Factory Reset in

for the input source. You can select a gamma table that has been specifically

To set a preset for the current source, adjust the image, select Save Settings

GammaGamma tables contain preset intensity configurations optimized

tuned for either film, video, Bright Room, or PC input. (Film input is mate-

rial originally captured on a film camera, like a movie; video input is mate-

event.) White Peaking increases the brightness of whites that are near 100%.

PresetsThis allows you to customize settings and save the settings to be

in the Presets menu, then choose Save User 1, 2, or 3. You can recall these

rial originally captured on a video camera, like a TV show or sporting

settings in the future by selecting the appropriate user presets.

Overscan: lets you crop the input or zoom the input if desired.

options and pick the one you like the best.

the Settings>Service menu.

Show 4 more labels / short text on this page
Save User Presets · Presets · Gamma · Overscan
Page 25 of the InFocus 5700 user manual — Advanced settings
Page 25 · click to enlarge
Page 25
InFocus 5700 — Picture menu diagram (page 25)
Fig. 27 · Picture menu
InFocus 5700 — Picture menu diagram (page 25)
Fig. 28 · Picture menu
InFocus 5700 — Picture menu diagram (page 25)
Fig. 29 · Picture menu

tion progressive component sources are not routed though this processor by

noise reduction, choose Auto to have the software determine the amount of

TrueLife: This option refers to Faroudja’s TrueLife processing of the image.

component) are routed through this processor. Extended and High Defini-

default. You can turn TrueLife on to route these signals through the proces-

lacer attempt to perform 3:2 pulldown, assuming the source was originally

created on 24fps film. If the original source is 30fps film, you should select

applied to skin tones. Images of people often look better with less process-

CCS(Cross Color Suppression) processes the signal to remove any color

information from the luma portion of the signal. It is On for all composite

signals, and can be turned off for S-video and inter-laced component sig-

Film Modecontrols deinterlacing. 2:2/3:2 Enable If selected, the deinter-

Tracking: adjusts the frequency of the video signal’s digital conversion.

All standard definition interlaced video signals (composite, S-video and

Noise Reductionadjusts signal noise reduction. Choose Off to have no

Skintone Bypass prevents the noise reduction processing from being

The following 4 options are for computer or HDTV sources only.

Phase: adjusts the phase of the video signal’s digital conversion.

Horizontal/Vertical Position: adjusts the position of the source.

Chroma Delayaligns the Luma and Chroma Detail

noise reduction, or choose Manual and adjust the Level.

Chroma Detail: This adjusts the color sharpness.

ing. Available when Auto or Manual are selected.

Luma Detail: This adjusts the sharpness.

sor and then adjust the following 3 options:

Advanced settings

NTSC 2:2 pulldown.

nals.

Show 4 more labels / short text on this page
Film Mode · True Life · Noise reduction · Advanced
Page 26 of the InFocus 5700 user manual — Picture menu
Page 26 · click to enlarge
Page 26
InFocus 5700 — Picture menu diagram (page 26)
Fig. 30 · Picture menu
InFocus 5700 — Picture menu diagram (page 26)
Fig. 31 · Picture menu
InFocus 5700 — Picture menu diagram (page 26)
Fig. 32 · Picture menu

REC709 for component 1080i or 720p sources, or choose REC601 for compo-

video standard options may vary depending on your region of the world.) If

look right or the image may appear “torn.” If this happens, manually select

Color SpaceThis option applies to computer and HDTV sources (it won’t

appear in the menu for video sources). It allows you to select a color space

that has been specifically tuned for the video input. When Auto is selected,

the projector automatically determines the standard. To choose a different

Color Controlallows you to individually adjust the gain (relative warmth

a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-

Video StandardWhen it is set to Auto, the projector attempts to pick the

of the color) and the offset (the amount of black in the color) of the red,

video standard automatically based on the input signal it receives. (The

the projector is unable to detect the correct standard, the colors may not

Color Temperaturechanges the intensity of the colors. Select a listed

setting, turn off Auto, then choose RGB for computer sources, choose

nent 480p or 576p sources.

green, and blue colors.

dard menu.

value.

Show 4 more labels / short text on this page
Color Control · Color Temperature · Video Standard · Color Space
Page 27 of the InFocus 5700 user manual — Settings menu
Page 27 · click to enlarge
Page 27
InFocus 5700 — Settings menu diagram (page 27)
Fig. 33 · Settings menu
InFocus 5700 — Settings menu diagram (page 27)
Fig. 34 · Settings menu
InFocus 5700 — Settings menu diagram (page 27)
Fig. 35 · Settings menu

checked, the projector defaults to the last-used source. If no source is found,

You can use the Source Enable feature to eliminate certain sources from this

Sourcesallows you to assign a particular input to a specific source key on

a blank screen displays. When Autosource is checked, the projector checks

sources are checked. Uncheck a source’s box to eliminate it from the search.

High PowerTurn this on to increase the light output of the lamp. This also

the last-used source first at power up. If no signal is present, the projector

are made once the unit has fully warmed up (approximately 20 minutes).

Display Messagesdisplays status messages (such as “Searching”) in the

the remote and enables or disables Autosource. When Autosource is not

checks the sources in order until a source is found or until power down.

Auto PowerWhen Auto Power is checked, the projector automatically

goes into the startup state after the projector receives power. This allows

search, which will speed the search. By default, the check boxes for all

Rearreverses the image so you can project from behind a translucent

Ceiling: turns the image upside down for ceiling-mounted projection.

control of ceiling mounted projectors with a wall power switch.

All options in this menu toggle between on and off.

shortens lamp life and increases fan noise.

lower-left corner of the screen.

Settings menu

screen.

Show 5 more labels / short text on this page
Source Enable · Sources Settings menu · System menu · Source 1 · System
Page 28 of the InFocus 5700 user manual — Settings menu
Page 28 · click to enlarge
Page 28
InFocus 5700 — Settings menu diagram (page 28)
Fig. 36 · Settings menu
InFocus 5700 — Settings menu diagram (page 28)
Fig. 37 · Settings menu
Sleep Timerallows you to force the projector to automatically shutoff after
Power Savewhen On, the lamp is automatically turned off after no signals

from being completely covered by the menus while you are making image

are detected for 20 minutes. After 10 additional minutes with no signal, the

Translucent OSDmakes the menus translucent. This prevents the image

projector powers down. If an active signal is received before the projector

Startup Logoallows you to display a blank Black, White, or Blue screen
Blank Screendetermines what color displays when you press the Blank

Chime: turn this on to hear a sound when the Power button is pressed.

instead of the default screen at startup and when no source is active or

Languageallows you to select a language for the onscreen display of

button on the remote or when no source is detected.

powers down, the image will be displayed.

menus and messages.

adjustments.

detected.

4 hours.

Show 4 more labels / short text on this page
System menu · Startup logo · Blank Screen · Language
Page 29 of the InFocus 5700 user manual — Cleaning the lens
Page 29 · click to enlarge
Page 29

with a soft dry cloth

InFocus 5700 — Maintenance diagram (page 29)
Fig. 38 · Maintenance
Test Patterndisplays a test pattern when the Blank button on the remote is

2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you don’t intend to use the projector immediately, replace the lens cap.

Blue Onlyturns off the Red and Green portions of the input, allowing you
ADC Calibrationallows adjustment of the calibrated ADC values so that

cleaner directly to the lens. Abrasive cleaners, solvents or other harsh

Factory Resetrestores all settings (except Lamp Hours) to their default

pressed. To select the patterns, use the up/down arrows on the remote or

color accuracy can be optimized. Adjust the slidebars for each value and

Color Wheel Index: makes the hue of various gray levels consistent.

Avoid using an excessive amount of cleaner, and don’t apply the

to properly adjust the color balance with a SMPTE color bar pattern.

1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

Service: to use these features, highlight them and press Select.

Service Code: only used by authorized service personnel.

after displaying a confirmation dialog box.

chemicals might scratch the lens.

adjusting the Component controls.

Cleaning the lens

Maintenance

keypad.

Show 4 more labels / short text on this page
Service menu · and non-abrasive · clean the lens · cleaner
Page 30 of the InFocus 5700 user manual — Replacing the projection lamp
Page 30 · click to enlarge
Page 30
InFocus 5700 — Replacing the projection lamp diagram (page 30)
Fig. 39 · Replacing the projection lamp

loosen the screw on lamp module

turn off and unplug

lamp has been in use. After 1980 hours, the message “Change lamp” briefly

3 Turn the projector upside down and remove the lamp door by removing the two screws and sliding the lamp door tabs out of the three tab bays.

mance, we recommend changing the lamp after 2000 hours, depending on

The lamp hour timer in the About menu counts the number of hours the

usage. You can order new lamp modules from your dealer. See “Accesso-

appears on the screen at each startup. To maintain optimal video perfor-

This disrupts the air flow and causes the projector to overheat.

2 Wait 60 minutes to allow the projector to cool thoroughly.

1 Turn off the projector and unplug the power cable.

4 Loosen the captive screw on the lamp module.

Replacing the projection lamp

ries” on page 32 for information.

Show 4 more labels / short text on this page
wait 60 minutes · Lamp hours used · the projector · bail wire
Page 31 of the InFocus 5700 user manual — Using the security lock
Page 31 · click to enlarge
Page 31

M1-DA vesa trigger 1 8 2 1

D5

Y Y

  • To avoid burns, allow the projector to cool for at least 60 minutes before
  • Do not touch the glass lamp screen. Fingerprints can obscure projection

System. See “Accessories” on page 32 for ordering information. Refer to the

  • Do not drop the lamp module. The glass may shatter and cause injury .
  • Be extremely careful when removing the lamp module. In the unlikely

event that the lamp ruptures, small glass fragments may be generated.

The lamp module is designed to contain most of these fragments, but

8 Replace the lamp door by sliding the tabs into the tab bays and tighten- ing the two screws.

9 Plug in the power cable, then press the Power button to turn the projec- tor back on.

5 Carefully remove the lamp module by grasping and lifting the metal bail wire. Dispose of the lamp in an environmentally proper manner.

To reset the lamp age, simultaneously hold down the two Brightness but-

6 Install the new lamp module, making sure that it is properly seated.

The projector has a security lock for use with a PC Guardian Cable Lock

information that came with the lock for instructions on how to use it.

tons on the projector’s keypad for 10 seconds.

use caution when removing it.

10 Reset the lamp hour timer.

Resetting the lamp timer

7 Tighten the single screw.

you replace the lamp.

Using the security lock

WARNINGS :

sharpness.

Show 10 more labels / short text on this page
security lock · trigger 2 · video · component · Pb Pb · Pr Pr · s-video · component · serial control · IR in
Page 32 of the InFocus 5700 user manual — Specifications
Page 32 · click to enlarge
Page 32

Optional Accessories Part Number

26” - 47” SP-LTMT-EXTP

Replacement Lamp Module SP-LAMP-006

Shipping Case (ATA approved) CA-ATA-013

False Ceiling Plate for Projector Mount SP-LTMT-PLT

North American Power Cable,1m SP-PC-US1M

PC Guardian Cable Lock System SP-LOCK

30’ Audio/Video Cable SP-AV30

(ship with the projector) Part Number

Shipping Box (with packaging) 110-0619-01

Power Cable (country-dependent) 210-0023-xx

Extension Arm for Projector Mount

Projection Lamp Module (included

Accessories

Humidity Operating 10% to 95% relative humidity, non-condensing Non-operating 10% to 90% relative humidity, non-condensing

Dimensions 13.8 x 12.8 x 4.3” (351W x 325L x 110H mm)

Temperature Operating 50 to 95° F (10 to 35° C) at 0 - 7,500 feet Non-operating -4 to 158° F (-20 to 70° C) at 0 -20,000 feet

Ceiling Mount UL tested/listed ceiling mount with minimum capacity of

Lamp Type UHP lamp (dual watt: 200 and 250 watt)

Altitude Operating 0 to 7,500 feet (2,286 meters) Non-operating 0 to 20,000 feet (6,096 meters)

Optics Focus Range 5 - 32.8 feet (1.5 - 10 meters)

Weight 9.3 lbs. (4.24 kg) unpacked

Input Power Requirements 100V-120V 4A, 50/60 Hz

200V-240V 2A 50 Hz

Specifications

Appendix

46 lbs (20.87 kg)

Show 10 more labels / short text on this page
Projector Mount SP-CEIL-005 · Cable Cover HW-CABLECVR-001 · in projector) SP-LAMP-006 · Director Remote 590-0567-01 · Lens Cap 505-1247-xx · User’s Guide 010-0466-xx · Safety Card 009-0659-xx · SCART cable* 210-0249-xx · Standard Accessories · *country-dependent
Page 33 of the InFocus 5700 user manual — Table 3: Red LEDs
Page 33 · click to enlarge
Page 33

27x48 .69x1.22 55.1/1.4 7.5/2.3 10.4/3.19

34x60 .9x1.5 68.8/1.75 9.42/2.87 13.06/3.98

40.5x72 1.0/1.8 82.6/2.1 11.09/3.38 15.36/4.68

45x80 1.1x2.0 91.8/2.3 12.27/3.74 17.03/5.19

52X92 1.3X2.3 105.6/2.7 14.21/4.33 19.69/6.0

54X96 1.4X2.4 110.1/2.8 14.93/4.55 20.7/6.31

58X104 1.5X2.6 119.3/3.0 16.14/4.92 22.38/6.82

65X116 1.7X3 133.1/3.4 18.54/5.65 25.72/7.84

49x87 1.2/2.2 99.8/2.5 13.48/4.11 18.7/5.7

Range of projection distances for a given screen size

Table 4:

Projected image size

tive image size calculator.

16:9 Screen dimensions

If the projector is not functioning properly and the red LED is blinking, con-

Five (5) blinks The projector is overheating. Check for a

attempts. Check the lamp and lamp door

Turn off the projector, wait one minute,

then turn it back on. Replace the lamp if

the projector does not turn on. Contact

Four (4) blinks The fan has failed. Replace the lamp (the

sult Table 2 to determine a possible cause. There are two second pauses

between the blinking cycles. Visit www.infocushome.com/support for

Three (3) blinks The projector has shut down the lamp.

Technical Support for repair if replacing

Technical Support for repair if replacing

blocked air vent. Contact Technical Sup-

the lamp does not solve the problem.

lamp module contains a fan). Contact

port for repair if clearing the air vents

One (1) blink The lamp won't strike after five (5)

the fan does not solve the problem.

installations for loose connections.

does not solve the problem.

Red LED behavior and projector errors

Table 3: Red LEDs

Red LED Behavior Explanation

more details on the red LED error codes.

Show 11 more labels / short text on this page
Minimum · (feet/m) · zoom · Projection Distance · Maximum · (feet/m) · zoom · (inches/m) · diagonal · Screen · (inches/m)
Page 34 of the InFocus 5700 user manual — Source compatibility
Page 34 · click to enlarge
Page 34

1-M1-DA VESA HDTV RGB, HDTV component, DVI, computer, and USB

1-Component (D5) HDTV, EDTV, Standard TV, RGB SCART with adapter

2-3.5 mm mini jack 1-12v screen drop, 1-12v 4:3 aspect “curtains”

2-Component (Gold RCA) HDTV, EDTV, and Standard TV component

1-HD15 VESA HDTV RGB, HDTV component, computer

1-3.5 mm mini jack IR Repeater (Niles/Xantech compatible)

Projector Inputs and Outputs

Table 6:

1-Composite (RCA) Standard Video

1-9-pin Dsub male RS-232

SECAMM, Component, Composite and S-Video standard

Video Component and RGB HDTV (720p, 1035i, 1080i, 1080p,

Computer Digital and analog PC, Macintosh, 1280x1024 resolution

1080p-24Hz) DVI/HDCP for digital video and encrypted digital video

Component EDTV (480p, 576p progressive scan),

video (480i, 576i, 576i RGB SCART with adapter,

Table 5:

NTSC, NTSC M 4.43,

PAL: B, H, I, M, N)

cation USB and RS-232

Source compatibility

2-S-Video Standard Video · Source Compability · Communi-

Page 35 of the InFocus 5700 user manual — Projector dimensions for ceiling mount installations
Page 35 · click to enlarge
Page 35
InFocus 5700 — Projector dimensions for ceiling mount installations diagram (page 35)
Fig. 40 · Projector dimensions for ceiling mount installations

8.5” 216mm

0.14” 3.6mm

4.3” 109.5mm

8.7” 221.4mm

Projector dimensions for ceiling mount installations

2.1” 53.7mm

2.3” 57.8mm

12.3” 312.7mm

InFocus 5700 — Projector dimensions for ceiling mount installations diagram (page 35)
Fig. 41 · Projector dimensions for ceiling mount installations
dimensions of optional cable cover12.4 x 3.9 x 3.2” (315 x 100 x 82mm)
InFocus 5700 — Projector dimensions for ceiling mount installations diagram (page 35)
Fig. 42 · Projector dimensions for ceiling mount installations

11.3” 288.1mm 2.6” 64.9mm

total length with optional cable cover: 16.2” 411.5mm)

Page 36 of the InFocus 5700 user manual — Communication configuration
Page 36 · click to enlarge
Page 36

understood, a “?” is returned. With absolute settings, “0” is off, 1-9999 is on.

Brightness (BRT10) Sets the brightness to 10

greater than the maximum range is received, it is automatically set to the

maximum number for that function. If a command is received that is not

A read command returns the range and the current setting, for example:

Some commands have ranges, while others are absolute. If a number

The one exception is the Power command, where 0 is off and 1 is on.

Lamp hours (LMP?) (0-9999, 421)

#### denotes the value to be written

(leading zeros not necessary)

Power (PWR0) Turns power off

Power (PWR1) Turns power on

Brightness (BRT?) (0-22, 10)

AAA denotes the command

( starts the command

) ends the command

A write request example(AAA####) where

To control the projector from an LCD control panel, connect an RS-232 cable

enclosed in parentheses. The request can be a read request (indicated by a

to the serial control connector on the projector and set your computer’s

All commands consist of 3 alpha characters followed by a request, all

serial port settings to match this communication configuration:

? denotes the read request

AAA denotes the command

“?”) or a write request (indicated by 1 to 4 ASCII digits).

( starts the command

) ends the command

Bits per second 19,200

RS-232 terminal specifications

A read request format(AAA?) where

Communication configuration

Command format

Show 9 more labels / short text on this page
Function Command Response · Function Command Response · Power (PWR9999) ? · Setting Value · Parity None · Flow control None · Emulation VT100 · Data bits 8 · Stop bits 1
Page 37 of the InFocus 5700 user manual — Supported commands
Page 37 · click to enlarge
Page 37

Contrast CON 8-252 128

Factory Reset (Write only) RST 0-1 n/a

Green Color Offset GCO 1-63 32

Green Gain GCG 1-63 32

Horizontal Position HPS n/a n/a

Keystone DKC 2-254 128

Luma Detail LDE 8-248 128

CCS CCS 0-1 0

Display Messages DMG 0-1 1

High Power Enable HPE 0-1 0

Lamp Hours (Read only) LMP 0-32767 0

Lamp Reset LMR 0-32767 0

Menu MNU 0-1 0

Gamma Table GTB 0-4 0 = PC 1 = Video 2 = Film 3 = Bright Room 1 4 = Bright Room 2

Color Temp TMP 0-2 0 = 9300 1 = 8200 2 = 6500

Menu Navigation NAV 0-4 0 = up 1 = down 4 = select

Function Command Range Default

Blue Color Offest BCO 1-63 32

Blue Gain BCG 1-63 32

Brightness BRT 8-252 128

Chroma Detail CDE 8-248 128

Color CLR 8-252 128

Auto Chime Enable ACE 0-1 1

Auto Power APO 0-1 0

Auto Source ASC 0-1 1

Blank BLK 0-1 0

Ceiling CEL 0-1 0

Aspect Ratio ARZ 0-4 0 = Native 1 = 16:9 2 = 4:3 3 = Letterbox 4 = Natural Wide

Color Space CSM 0-7 0 = RGB 3 = REC601 2 = REC709 7 = Auto

Blank Screen BSC 0-2 0 = black 1 = blue 2 = white

Supported commands

n/a

Page 38 of the InFocus 5700 user manual — RS-232 terminal specifications
Page 38 · click to enlarge
Page 38

Tint TNT 8-252 128

Tracking MTS 2148-2248 n/a

Vertical Position VPS n/a n/a

Skintone Bypass Enable SBE 0-1 1

Startup Logo DSU 0-1 1

Translucent OSD TOE 0-1 1

TrueLife Enable TLE 0-1 1

Source SRC 0-7 0 = Video 1, M1 1 = Video 2, VESA 2 = Video 3, Com- ponent 1

7 = Video 8, D5

5 = Video 6, Component 2

3 = Video 4, S-Video 1

4 = Video 5, S-Video 2

6 = Video 7, Composite

Video Standard VSU 0-3 0 = Auto 1 = NTSC 2 = PAL 3 = SECAM

Phase MSS 0-31 n/a

Red Color Offset RCO 1-63 32

Red Gain RCG 1-63 32

NTSC 2:2 Pulldown Enable NPE 0-1 0

Noise Reduction Level NRL 8-248 8

Overscan OVS 0-1 0

Power PWR 0-1 0

Power Save PSV 0-1 0

Rear Project REA 0-1 0

Language LAN 0-11 0 = English 1 = French 2 = German 3 = Spanish 4 = Chinese Tradi- tional

5 = Japanese 6 = Korean 7 = Portuguese 8 = Russian 9 = Norwegian 10 = Chinese Sim- plified

Noise Reduction Enable NRE 0-2 0 = Off 1 = Auto 3 = Manual

Presets PST 0-2 0 = User 1 1 = User 2 2 = User 3

11 = Italian

Page 42 of the InFocus 5700 user manual — WARRANTY LIMITATION AND EXCLUSION
Page 42 · click to enlarge
Page 42

erly use the Product in the application for which said Product was intended.

This Limited Warranty excludes Product cleaning, repair, or replacement of

unusual Product wear and is not considered normal use under the terms of

OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS.

and excludes normal wear. The Lamp Product Limited Warranty excludes

Remanufactured Products and Software Products are exempt from the fore-

Product Limited Warranty or Software Product Limited Warranty for appli-

THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI-

THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED

exposure (cigarette or otherwise), accident, unusual physical or electrical

authorized agents, causes other than from ordinary use or failure to prop-

plastics due to cosmetic damage and damage as a result of normal wear.

The Accessory Product Limited Warranty covers the accessory item only

going Limited Warranty. Please refer to the appropriate Remanufactured

CABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR

RANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR

EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND

LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS

Product repair outside of the terms of the Limited Warranty will be on a

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-

PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT

stress, unauthorized modifications (including use of an unauthorized

mount), tampering, alterations, or service other than by InFocus or its

SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW

time and materials basis. Prolonged Product “demonstration” causes

DISCLAIMER OF UNSTATED WARRANTIES

expected lamp degradation.

cable Warranty information.

MAY NOT APPLY TO YOU.

this Limited Warranty.

If the Product while subject to this Limited Warranty, is defective in material

equivalent or superior to new parts performance. Limited Warranty periods

  • Lamp Product Limited Warranty Periods: From the date of Projector

ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PUR-

ranty if the Product has been damaged due to abuse, misuse, neglect, smoke

Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Cor-

within the Limited Warranty period and to repair or replace defective parts

with new parts or, at the option of InFocus, serviceable used parts that are

500 hours usage Limited Warranty Period, whichever comes first, and replacement Lamps purchased at the time of Projector Product pur-

  • Accessory Product Limited Warranty Period: one (1) year from date

THIS WARRANTY SETS FORTH INFOCUS’ MAXIMUM LIABILITY FOR

CHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER.

InFocus shall have no further obligation under the foregoing Limited War-

poration (“InFocus”) warrants that the Projector, Lamps and Accessories

(hereinafter collectively or individually referred to as “Product” as appro-

reseller will conform to InFocus’ specifications and be free from defects in

material or workmanship for the respective Limited Warranty period pro-

vided below. InFocus does not warrant that the Product will meet the spe-

or workmanship during the warranty period, then InFocus, at its option,

All exchanged parts and Products replaced under this Limited Warranty

will become property of InFocus. InFocus’ sole obligation is to supply (or

Product purchase, the original installed lamp shall have a 90-day or

  • Projector Product Limited Warranty Period (Excluding Lamps):

priate) purchased from InFocus, an InFocus distributor, or an InFocus

pay for) all labor necessary to repair the Product found to be defective

chase will have a 500 hours usage Limited Warranty period.

WARRANTY LIMITATION AND EXCLUSION

cific requirements of the end-user customer.

Two (2) years from date of purchase.

will REPAIR or REPLACE the Product.

of purchase.

are as follows:

Limited Warranty

Page 43 of the InFocus 5700 user manual — WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE
Page 43 · click to enlarge
Page 43

No repair or replacement of Product or part thereof shall extend the Limited

NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF

Mandatory Arbitration – Any action, regardless of form, arising out of the

chase, to the manufacturer (Purchaser must bear all tax, duty and freight),

workmanship shall only be effective for a period of ninety (90) days follow-

THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND

CIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR

Limitation on Bringing Action - No action, regardless of form, arising out

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES

InFocus, proof of legal import must accompany the warranty repair Prod-

Warranty period as to the entire Product. Warranty on the repair part and

UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPE-

Governing Law - Any action, regardless of form, arising out of the agree-

INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS,

Upon request of InFocus Corporation or an authorized repair center for

uct, otherwise the Product must be returned to the place of original pur-

ing the repair or replacement of that part or the remaining period of the

WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN

STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING

of the agreement to purchase the Product may be brought by purchaser

agreement to purchase the Product is subject to mandatory arbitration.

LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE

IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY

or the Purchaser must bear charges for the warranty repair.

ment to purchase the Product is governed by Oregon law.

more than one year after the cause of action has accrued.

Product Limited Warranty whichever is greater.

DEPENDING ON JURISDICTION.

LIMITATION OF LIABILITY

INFOCUS’ LIABILITY.

The Limited Warranty periods hereof commence on the date of purchase by

the end-user customer. These Limited Warranty provisions shall apply only

to the end-user purchaser (first person or entity that purchased a new Prod-

resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS

DURATIONS PROVIDED HEREIN, AND INFOCUS WILL HONOR ALL

Any person exercising a claim under this Limited Warranty must establish

to the satisfaction of InFocus both the date of purchase and that the Product

During the Limited Warranty period, to exercise this Limited Warranty, the

For Warranty service, the purchaser will be advised to return or deliver the

defective Product freight and all fees prepaid, to an InFocus Service Center

InFocus, a Return Material Authorization Number (RMA ); is required and

must be clearly displayed on the outside of the shipping carton or a similar

Products returned for Warranty service must be accompanied by a written

letter that(i) explains the problem; (ii) provides proof of date of purchase;

(II) provides the dealer’s name; and (I) provides the model and serial num-

uct for personal or business use and not for the purpose of distribution or

WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE

was purchased new. The sales receipt or invoice, showing the date of pur-

purchaser must first contact 1) InFocus, 2) a service facility authorized by

or to a service facility authorized by InFocus. When returning Product to

facility authorized by InFocus will return the repaired/replaced Product

InFocus Customer Service – 1-800-799-9911 or techsupport@infocus.com

package affording an equal degree of protection. InFocus or the service

chase of the Product is the proof of the date of purchase.

To Be Eligible For Limited Warranty Coverage

InFocus or 3) the place of original purchase.

freight prepaid to the purchaser.

SUCH CONSUMER RIGHTS.

To Obtain Warranty Service

ber of the Product.

Limited Warranty Period

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No startup screenPlug power cable in and remove lens cap press Power button p.12
Image not centered on screenMove projector, adjust zoom, adjust height zoom Adjust horizontal or vertical position in Picture>Advanced menu p.12

Ask about the InFocus 5700

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus 5700

Be the first to ask — other owners or our team will answer.

Original document

InFocus 5700 manual PDF

43 pages·2.9 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…