



fold and tear here fold and tear here
Connecting the LitePro is summarized on the back of this card and described in detail in the LitePro 560/570 User’s Guide.
The User’s Guide contains instructions and illustrations for connections to all compatible computers. It also describes the remote control buttons and menu functions.


You must install the projection bulbs the first time you use the LitePro. Refer to the “Read Me First” card or page 40 of the User’s Guide for instructions.
Connect the LitePro cable to the monitor connector on your com- puter.
If you want to display your presen- tation on your computer’s monitor as well as on the projection screen, attach the “MONITOR” end of the LitePro cable to the end of the monitor’s cable.
Place the LitePro on a flat surface within six feet of your power source and your computer.
Remove the lens cover.
LP570 only: If you want to connect your computer’s sound board, a video player, a speaker system, a microphone, or a second computer, refer to the instructions in User’s Guide.
Plug in the LitePro’s power cord.
Make sure your computer and monitor are turned off.
Plug the “LCD” end of the LitePro cable into the “COMPUTER” con- nector on the side of the LitePro.
If you attached your monitor in Step 8, turn on the monitor.
If your computer is a Macintosh, attach the Mac adapters before doing step 8. Attach one adapter to the “VGA” end of the LitePro cable. Attach the other adapter to the “MONITOR” end of the LitePro cable.
Press the “|” side of the power switch to power up the LitePro. The test pattern will be projected onto the screen. If necessary, adjust the height of the LitePro and focus the lens.
Locate your computer’s monitor cable. Unplug it at the computer end, leaving the monitor end attached.
Turn on your computer. The com- puter image will be projected onto the screen.
If your computer is... You’ll need...
IBM-compatible desktop or laptop no adapters
Apple Macintosh or PowerBook 2 Mac adapters
Macintosh PowerBook 1 Mac adapter and your video-out cable

Copyright © 1995 by In Focus Systems, Inc.
Wilsonville, Oregon. All rights reserved.

UL 1950, CSA 950, EN 55022, EN 50082-1, EN 60950
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause harmful interference to radio and television reception. Operation of this equipment in a residential area is likely to cause harmful interference. If this equipment does cause interference to radio or television reception, the user is required to correct the interference at his/her own expense. The user may try to correct the interference by one or more of the following measures:
This product is intended for use in a commercial, industrial, or educational environment. It is not intended for residential use.
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.
Wenn das Produkt Lite Pro 560/570 in Deutschland verkauft wird, muss es Umwelt geschuetzt sein. (Klasse B) Dieses Product muss mit dem Bundesamt fuer Post und Telekommunikation registriert sein. (BAPT)
All trademarks are the property of their respective owners and are used in this publication for identification purposes only.
The following are trademarks or registered trademarks of their respective companies:

We, In Focus Systems, Inc., 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA, declare under our sole responsibility that the:
LitePro 560 and LitePro 560LS LCD projector LitePro 570 and LitePro 570LS LCD projector
to which this declaration relates, are in conformity with the following standards:
EN 55022 Information Technology Equipment Emission Standard EN 50082-1 Generic Immunity Standard EN 60950: 1992+A1+A2: 1993 .Safety of Information Technology Equipment
following the provisions of the following directives:
EMC Directive 89/336/EEC, Amended by 93/68/EEC Low Voltage Directive 72/23/EEC, Amended by 93/68/EEC
European Office Planetenweg 91, 2132 HL Hoofddorp, The Netherlands
Declaration of Conformity · September, 1995


Please read these instructions before using your LitePro projector. Failure to comply with these instructions could result in fire, electrical shock, personal injury or equipment damage.
These graphics are used throughout this manual to draw your atten- tion to important information about the LitePro:
Information that may be unusual or unexpected.
Information that helps you avoid damage to your equipment.
Information that helps you avoid personal injury.
These graphics are used on the LitePro:
Fuse - Refer to “Replacing the Fuse” on page 43 of this User’s Guide for important safety information.
Hot Surface - Do not touch until the LitePro has cooled.
Do not look into the lens! Be very careful not to look into the projection lens when the projector is turned on. The bright light may harm your eyes. Be especially careful to keep children from looking into the lens.
Power Source Use only a three-wire grounding type power source. The power source should not exceed 250 volts rms between the supply conductors or between either conductor and the ground.
Power Cord Use only the power cord that was shipped with the LitePro. Although other power cords might be similar in appearance, they
LitePro 560/570 User’s Guide iii

have not been safety-tested with the LitePro. Never use a power cord if it has become damaged or frayed. Contact your In Focus dealer or call In Focus if you need to replace your LitePro power cord.
Grounding The LitePro is grounded through the grounding conductor on the power cord. To avoid electric shock, plug the power cord into a properly wired receptacle. Do not defeat the purpose of the grounding-type plug.
Fuse For protection against the risk of fire, use only a fuse of the specified type. Refer to page 51 for more information about fuse specifications and to page 43 for instructions on replacing the fuse.
Lamp To avoid overheating and unacceptable image quality, replace the projection lamp with a lamp of the specified type. Refer to page 51 for lamp specifications and to page 40 for instructions on replacing the lamps.
Hot Surfaces The rear of the LitePro becomes very hot during operation. Avoid touching the exhaust grill on the lamp door. Allow the LitePro to cools for at least 20 minutes before replacing a lamp. When you open the lamp door, be very careful not to touch the hot surfaces inside.
Ventilation and Overheating Openings in the LitePro case provide ventilation to protect it from overheating. Keep loose papers and other objects well away from the sides and back of the LitePro. Never operate the LitePro when the lamp door is open; this disrupts the cooling air flow inside and can cause the LitePro to overheat. Do not place the LitePro on top of or close to the computer or other heat-producing equipment.
Liquid Spills Do not set drinks on top of the LitePro. Spilled liquids can flow inside and damage the LitePro.
Do Not Disassemble The only user-serviceable parts on the LitePro are inside the lamp door at the rear. Do not open any other part of the LitePro. Opening the LitePro case will expose you to electric shock hazard. All service must be performed by an authorized In Focus service center.
iv LitePro 560/570 User’s Guide
Safety Summary

The In Focus Systems LitePro 560 and 570 LCD projectors provide 640x480 resolution with compatibility up to 800x600. The LitePro’s active matrix liquid crystal display (LCD) is based on Thin Film Transistor (TFT™) technology. It can display up to 16.7 million colors. The LitePro is ideal for high-performance business, CAD and imaging applications that demand high resolution and exceptional color quality.

Figure 1. Shipping Box Contents

The LitePro is compatible with a wide variety of computers:
The LitePro 560/570 is not compatible with these systems:
The resolution of the LitePro’s projected image is 640x480. The LitePro displays computer images that are 640x480 or lower just as they appear on your computer’s monitor. Screen resolutions between 640x480 and 800x600 are compressed to 640x480. The LitePro cannot display screen resolutions above 800x600. If your computer’s screen resolution is higher than 800x600, reset it to a lower resolution before you connect the LitePro.
The LitePro comes with these cables and adapters:
Introduction

The Remote Control Programmer Kit that was shipped with your LitePro allows you to program the LitePro’s remote control to perform up to four different operations on your computer. Refer to the Remote Control Programmer User’s Guide for more information.
The first place to look for help is in this manual. Be sure to check the troubleshooting guidelines in “Troubleshooting” starting on page 47.
If this manual does not answer your question, call your In Focus dealer. You can also call In Focus Technical Support directly at 1-800-294-6400. Call between 6 a.m. and 5 p.m. PST, Monday through Friday. In Europe, call In Focus in The Netherlands at (31) 23 5623200.
Your LitePro is backed by a limited one-year warranty. The details of the warranty are printed at the back of this manual.
Introduction

This chapter describes how to position the LitePro projector for optimum viewing and how to connect it to your equipment.

5.7 ft. (1.7m) 7.2 ft. (2.2m) 9.9 ft. (3m)

Setting Up the LitePro

Figure 3. Connecting the “LCD” end of the LitePro cable

Setting Up the LitePro
The resolution of the LitePro’s image is 640x480. Images between 640x480 and 800x600 resolution are displayable, but
will be compressed. Images above 800x600 are not
displayable.
If your computer’s screen resolution is greater than 800x600,
you will need to reset it to 800x600 or less. Refer to your
computer’s documentation for instructions.
If you want to display your presentation on your monitor as well as on the projection screen, attach the “Monitor” end of the LitePro cable to the end of the monitor cable as shown below.

power switch “Monitor” end of
monitor cable “VGA” end of LitePro cable
Figure 4. Connecting an IBM-compatible desktop computer
LitePro cable

Setting Up the LitePro
If you want to display your presentation on your monitor as well as on the projection screen, attach the “Monitor” end of the LitePro cable to the other Mac adapter. Then connect the Mac adapter to the end of the monitor cable as shown below.

power switch “Monitor” end of
monitor cable “VGA” end of LitePro cable Mac adapter Mac adapter
Figure 5. Connecting a Macintosh desktop computer
LitePro cable

Setting Up the LitePro

power switch “Monitor” end of
“VGA” end of LitePro cable
Figure 6. Connecting an IBM-compatible laptop computer
The LitePro connects to a laptop computer through the computer’s external monitor port. Most laptop computers do not automatically activate their external monitor port when a device such as the LitePro is connected. Refer to your computer manual for the command that activates the external video port. The ”Laptop Display Activation Chart” on page 56 lists the commands that activate the external monitor port for a variety of computers.
LitePro cable

Setting Up the LitePro
If you have an Apple PowerBook Duo computer, you must have a DuoDock adapter (which provides a video out connector). You’ll also need one of the Mac adapters that came with the LitePro. Follow the instructions for connecting a PowerBook.

“VGA” end of LitePro cable
power switch “Monitor” end of
Figure 7. Connecting a Macintosh PowerBook
Tighten the thumb screws on all cable connectors to ensure
proper grounding.
video out · LitePro cable · cable

Setting Up the LitePro
If the audio connector on your computer’s sound board is a
mini-type jack, you will need an RCA jack-to-mini plug
adapter. Refer to ”Accessories” on page 53 for order
information.

connect video cable to either SOURCE 3 or SOURCE 4 connector

Setting Up the LitePro

connect video cable to either SOURCE 3 or SOURCE 4 connector
The video-out connector on your video player may be labeled
“To Monitor.”

Setting Up the LitePro

Figure 10. Connecting the Audio from a Video Player

Setting Up the LitePro
You must use an amplified external speaker with the LitePro.
A non-amplified (passive) speaker will not work.


Setting Up the LitePro
Always keep the source volume at its lowest level when installing the microphone. For setting the microphone level,
refer to”Volume and Audio Lock” on page 36.

Always use the power cord that was shipped with your LitePro. The projector accepts power from 100 VAC and 220 VAC, 50 or 60 Hz, three-wire type grounded sources. When you
disconnect the projector, always remove the power cord from
the electrical outlet first, then from the projector.

Setting Up the LitePro
With some computers, the order in which you power up the equipment is very important. We recommend that you always
turn on the LitePro FIRST. This is especially important if your
computer is a Macintosh.
Your LitePro is now ready to use. See ”Using the LitePro” on page 17 for information about using the remote and the on-screen menu.

This section describes how to use and make adjustments to the LitePro 560/570. It also provides a reference to the remote control buttons and the menu commands.
It is very important to allow the projector to cool down before turning it completely off. Turning the projector off is a two-step process:
Point the remote control at the projection screen or at the front of the LitePro. The range for optimum operation of the remote control is a total of about 25 feet. If you point the remote at the projection screen, the distance to the screen and back to the LitePro should be less than or equal to 25 feet.

To focus the image, rotate the projection lens until the image is clear. Rotate the lens clockwise for a longer focusing distance. Rotate it counterclockwise for a shorter focusing distance.
Your LitePro is equipped with a self-locking, quick-release elevator foot. If the projected image seems wider at the bottom than at the top, extend the elevator foot until the distortion is corrected.
To raise the LitePro:
To lower the elevator foot:
Always hold the LitePro’s handle when you press the
elevator’s quick release button.

The LitePro was shipped with two projection lamps. To avoid breaking during shipping, they are not installed at the factory. You must install them before you can use the LitePro. Refer to the “Read Me First” document that was shipped with your LitePro for instructions. “Replacing the Projection Lamps” on page 40 also describes this procedure.
When both lamps are installed in the LitePro, only one is used at a time. The other is available as a spare for when the active lamp fails. The average lamp life is about 50 hours.
To switch to the spare lamp:

When switching lamps, be careful not to touch the exhaust grill on the door. This area is very hot when
the projector is operating.


Figure 14. Remote Control Buttons
Pressing menu accesses the LitePro’s on-screen menus. There are three menus: Menu 1, Menu 2 and the Audio Menu. Menu 1 always displays first. Refer to “Using the Menus” on page 24 for more information about the menus.
When a menu is displayed, pressing menu again removes it from the screen. When you remove a menu, the LitePro saves any changes you made. The changes you made will be saved even after you turn the LitePro off.
LP 560LS & LP 570LS: When a LiteShow presentation is displayed, menu has a different function; it displays the LiteTable to allow you to edit your LiteShow presentation. Refer to the LiteShow User’s Guide for information about LiteShow presentations.
menu

The operations of the arrow buttons depend on what is displayed. When a menu is displayed, the left and right arrow buttons move the highlight bar to select a menu function. The up and down arrow buttons adjust or change the value of the highlighted function. The arrow buttons are auto-repeating; they repeat their function as long as you hold down the button.
When a computer or video image is displayed, the left and right arrow buttons perform their alternate functions, mute and mic. These are described below.
LP 560LS & LP 570LS: When a LiteShow presentation is displayed, the up and down arrow buttons perform their alternate functions, next and prev. These are described below.
The operation of the select/enter button also depends on what is displayed. When Menu 2 or the Audio Menu is displayed, select/ enter cycles forward through the available settings for the highlighted function.
When a computer or video image is displayed, select/enter switches among the sources that are connected and enabled, such as computer(s) in Source 1 and/or 2 and video player(s) in Source 3 and/or 4. If only one source is connected, select/enter switches between the source image and the test pattern. If the test pattern is turned off, select/enter switches between the source image and a blank screen. (Connecting sources is described starting on page 5. Enabling sources is described on page 31. Turning off the test pattern is described on page 29. Video players can only be connected to the LitePro 570.)
LP 560LS & LP 570LS: When a LiteShow presentation is displayed, the select/enter button has a different function. Refer to the LiteShow User’s Guide for more information.
LP 560LS & LP 570LS: When a LiteShow presentation is displayed, press next to advance to the next slide in your presentation. Refer to the LiteShow User’s Guide for more information.
arrow buttons · select/enter · next

LP 560LS & LP 570LS: When a LiteShow presentation is displayed, press the prev button to go back to the previous slide in your presentation. Refer to the LiteShow User’s Guide for information.
LP 570 & LP570LS: Pressing mute enables and disables both the external and internal audio functions.
LP 570 & LP 570LS: Pressing mic enables and disables the microphone.
The operation of the freeze/esc button depends on what is displayed. When a computer image, a video image or a menu is displayed, press freeze/esc to pause the display. Press it again to return to the current image.
LP 560LS & LP 570LS: When a LiteShow presentation is displayed, press freeze/esc to exit LiteShow menus and cancel LiteShow operations. Refer to the LiteShow User’s Guide for more information.
LP 560LS & LP 570LS: Press lite show to switch to your LiteShow presentation. Press lite show again to return to your computer or video image. Refer to the LiteShow User’s Guide for information about using LiteShow.
LP570 & LP 570LS: Pressing either end of the volume button adjusts the volume of the active audio source. (To activate a different audio source or lock the volume onto one source, see “Volume and Audio Lock” on page 36.)

The prog button is programmable. You can program it to perform any one of these functions.
Refer to “Prog Button” on page 32 for descriptions of these operations and instructions on how to program the button.
The standby button switches the projection lamp off. Press any button to turn it back on.
prog · standby

The LitePro has three menus: Menu 1, Menu 2, and the Audio Menu.
Menu 1 allows you to adjust the brightness, tint, synchronization (sync), and display positioning. Each of the these menu settings is described in “Menu 1 Functions” starting on page 26.
To display Menu 1:

Figure 15. Menu 1
If you see “EEPROM Failed” displayed on Menu 1, one of the
integrated circuits inside the LitePro has failed. The LitePro
will continue to operate normally. The only loss of functionality is that changes you make in the menus will not be saved after you turn the LitePro off. All settings will return
to their defaults. Call In Focus Technical Support. Refer to “If
You Need Assistance” on page 3 for the phone number.
Menu 2 contains controls for a variety of functions that you probably won’t need to change very often. Each of these is described later in this manual in “Menu 2 Functions” starting on page 28.
To display Menu 2:
Menu 1 · Menu 2


Figure 16. Menu 2
LP 570 & LP 570LS: The Audio Menu contains controls for the LitePro 570’s audio functions. Each of these is described later in this manual in “Audio Menu Functions” starting on page 36.
To display the Audio Menu:

Figure 17. Audio Menu
The right side of each menu contains information about the state of the LitePro. If you need to call In Focus Technical Support for assistance, they may need to know these values.
You must highlight a function before you can change its setting.
Making Changes to Menu Functions
When the function you want to change is highlighted, you can change the setting.
The Audio Menu · Highlighting Menu Functions

Removing the Menu from the Screen
Press the menu button to remove the menu from the screen.
Resetting Menu Functions to the Default Settings
To reset all menu settings to their factory default values, select Reset from Menu 2. Refer to page 30 for more information about Reset.
Adjusting the brightness changes the color saturation. Adjusting the brightness has no effect if a computer source is not connected.
To adjust the brightness:
The tint function adjusts the red-green color balance. Adjusting the tint has no effect if a computer is not connected.
To change the tint:
Brightness · Tint

The LitePro adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy, streaked or noisy, try adjusting the sync from this menu.
To adjust the Sync:
These functions allow you to change the vertical position of the projected image.
To re-position the display:
These functions allow you to change the horizontal position of the projected image.
To re-position the display:
Sync · Up/Down · Left/Right

When you select Rear Projection, the LitePro reverses the image so you can project from behind the screen as shown here.

To enable or disable to rear projection mode:
When you are displaying your presentation and you press select/ enter to switch sources, the LitePro momentarily displays the name of the active source. If you don’t want this display, follow the steps below to disable the Source Prompt.
To enable or disable the Source Prompt:
Rear Projection · Source Prompt

If the test pattern is turned on, it displays when the LitePro is first powered on and also when no computers or video players are connected to the LitePro. If the test pattern is turned off, it displays only when the LitePro is first powered on. As long as the test pattern is turned off, the only way to display it is to unplug the power supply cord, then plug it back in again. (Refer to “select/enter” on page 21 for additional information about the test pattern.)
To enable or disable the test pattern:
When the LitePro’s RS-232 connection is enabled, you can use the LitePro’s remote control to send commands to your computer. To use this feature, you must install the Remote Control Programmer that was shipped with your LitePro. Refer to the Remote Control Programmer User’s Guide for more information.
To enable or disable the RS-232 serial port:
When you enable Auto Standby, the LitePro automatically turns off the projection lamp after a specified period of time. You can specify 5, 10 or 30 minutes. If Auto Standby is turned off, you can still turn off the lamp by pressing the standby button on the remote. Refer to page 17 and page 23 for additional information about Standby.
Test Pattern · Auto Standby

To enable Auto Standby:
The Reset function changes all the menu function settings back to the factory default states.
The defaults are:
To reset your adjustments:
Reset

When you have more than one source (computer or video player) connected to the LitePro, you switch between them by pressing the select/enter button on the remote. If you have a source connected that you don’t want to display, use the Source Enable function to disable that source. That source will then be skipped when you press select/ enter.
If you disable a source, you will not be able to display it. You will have to return to Menu 2 and enable it again.
By default, all 4 sources are enabled.
To enable or disable a source:
You can select a color palette of 512, 24,389, 1.4 million or 16.7 million colors. The default is 24,389 colors.
If your computer’s graphics mode is EGA, the LitePro displays a maximum of 16 colors regardless of the Palette setting. When a video image is displayed, the LitePro displays 1.4 million colors, regardless of the Palette setting.
To change the color palette:
Source Enable · Palette

Use the Prog Button function to assign an operation to the remote’s prog button. You can assign any one of these functions.
To change the prog button assignment:
Prog Button

The Language function changes the language in which the LitePro menus are displayed. You can choose from English, French, German, Spanish or Italian. The default is English.
To change the language of the menus:
The LitePro usually adjusts tracking automatically when you connect your computer. However, if the display shows evenly spaced, fuzzy, vertical lines or if the projected image is too wide or too narrow for the screen, you might be able to improve it by adjusting the tracking manually with the Tracking function.
To adjust the tracking:
Language · Tracking

Text Mode and Pixel Slice
Some IBM-compatible computer display modes generate a 720 pixel- wide image which extends beyond the LitePro’s 640 pixel-wide image area. For most computers, the LitePro automatically enables Text Mode, compressing the display to fit. But if you are displaying text that appears to be truncated on the right side, you may need to manually enable Text Mode.
When you enable Text Mode, the LitePro compresses the image by removing every 9th column of pixels; this is referred to as “pixel slice”. There are 9 pixel slice settings. Choose the one that results in the most acceptable display.
To enable Text Mode:
Television video signal standards vary throughout the world. The LitePro can adapt to the three most common standards: NTSC, PAL and SECAM.
If you don’t know which standard is used in your area, select the one that provides the best image. The default setting is NTSC.
Video Type

To change the video type setting:
Comp.
Compress is only functional for PAL video displays. PAL video produces an image that is slightly too large for the LitePro to display. Enabling the Compress function compresses the image to fit.
To enable or disable PAL video compression:
Sharpness is only functional for NTSC, PAL and SECAM video images. If you notice “comb-like” edges in your video display, you may want to enable Sharpness. Turning Sharpness on smooths out the images. The “comb” effect is most noticeable in fast-moving videos that contain high contrast images.
To enable or disable video sharpness:
Sharpness

The Audio Menu is available on LP 570 & LP 570LS only.
Volume and Audio Lock
You can adjust the volume either with the volume button on the remote or from the Audio Menu. If you want to adjust the volume for all sources and the microphone at one time, it is probably easier to use the Audio Menu. (To adjust the volume using the remote, see “volume” on page 22.)
To adjust the volume from the Audio Menu:
Be sure that the microphone volume is set to a low level before you install a microphone. If it is set too high, you may
damage the LitePro’s speakers.
If you want to lock the audio on one of the sources, highlight the source and press select/enter. The LitePro enables Audio Lock, placing a padlock icon above the source. When an audio source is locked, the LitePro will always play it, regardless of which source is selected.
For example, if you are using a video in addition to a computer- ized slide show in your presentation, you might want to set Audio Lock on the video source (source 3 or 4). The audio por- tion of the videotape will continue to play even when you switch over to display the slide show on the computer.

The Bass function adjusts the lower frequencies of your audio source.
To adjust the bass for the selected audio source:
The Treble function adjusts the higher frequencies of your audio source.
To adjust the treble for the selected audio source:
Adjusting the balance controls the audio levels between the right and left channels of your audio source. The Balance function also fades the level between the internal and external speakers (if you have connected an external speaker).
To adjust the balance for the selected audio source:
Bass · Treble · Balance and Fade

Enabling Loudness adjusts the audio quality by enhancing the bass portion of the sound.
To enable or disable Loudness for the selected audio source:
Enabling Mute turns off the audio from the selected source. You can also mute the selected source by pressing the mute button on the remote when a computer or video image is displayed.
To select the mute function:
Loudness · Mute

This section describes how to:
Do not open the LitePro case! Opening the case will expose you to electric shock hazard! Except for the projection lamps, there are no user-serviceable
parts inside! If you are having problems with your LitePro, refer to “Troubleshooting” on page 47 of this User’s Guide. Call
In Focus Technical Support if necessary. If your LitePro needs
repair, they will refer you to an In Focus Authorized Service
Provider.
Follow these steps to clean the projection lens.

When a lamp fails, be sure to replace it with another EVD lamp (36 volt, 400 watt). These lamps provide the best performance and longest lamp life.
You can order replacement lamps from In Focus. Refer to “Accessories” on page 53 for information.
Follow these steps to replace the lamps.
Allow the LitePro to cool for at least 20 minutes before you attempt to open the lamp door! The inside of the LitePro lamp
housing can become very hot. Use extreme care.
Do not touch the lamps with your bare fingers. Always hold
them with a clean cloth. The natural oil on your skin
concentrates the heat and may destroy the lamps.
Maintenance



LA LAMPE ET LES PIECES METALLIQUES PEUVENT ETRE ENCORE CHAUDES
Maintenance

Never operate the LitePro with the lamp door open or removed. This disrupts the air flow, causing it to overheat.
Your LitePro is equipped with a lamp life detection system called Bulb Guard. When the operating lamp is near the end of its life or has become degraded, Bulb Guard causes the lamp to blink. When this happens, switch to the spare lamp. After you have finished your presentation and the LitePro has cooled, replace the old lamp with a new one.
Follow these steps to replace the batteries.

Maintenance · Bulb Guard


A power line surge or spike can blow the power supply fuse, causing the LitePro to stop working. If this happens, you’ll need to replace the fuse.
Use only the specified power supply fuse. Using a different
fuse may damage the LitePro.
The correct fuse depends on the power line voltage in the country where you are operating the LitePro.
A surge-protected power strip is recommended if power
surges are common in your area.
Follow these steps to replace the fuse.
Maintenance


Figure 22. Locating the Fuse
Maintenance



Figure 24. Inserting the New Fuse into the Fuse Holder
Maintenance

Do not open the LitePro case! Opening the case may cause electric shock! Except for the projection lamps, there are no user- serviceable parts inside. If you are having problems
with your LitePro, read through this section of this manual. Call In Focus Technical Support if necessary. They will refer you to an In Focus Authorized Service
Provider.
Before calling your dealer for assistance, follow these steps in this order to make sure everything is properly connected.

If you call In Focus for assistance:
Troubleshooting

Troubleshooting

Troubleshooting

Type tungsten halogen EVD bulb, 400 watt, 36 volt
Life Average 50 hours each
100 to 120V nominal line 10A, 250V, 3AB
220 to 240V nominal line 6.3A, 250V, 5x20mm
100 to 240 VAC, 7.2A to 2500 mA, 50 to 60 Hz.
Battery Two (2) AAA alkaline cells
Range 25 feet (7.62m) when reflected off a white wall or projection screen within 45° of the projection axis
Brightness peak performance 300 lumens (measured by ANSI 9 point method) typical performance 285 lumens (9 point)
Uniformity 1.9:1 maximum (12 point)
Projection Range 5 to 15 feet (1.5 to 4.6 m)

Operating Nominal 25°C *
Non-operating 0° to 60°C
Operating 0 to 10,000 feet (3048 meters)
Non-operating 20,000 feet (6096 meters)
10 to 90% RH, non-condensing
LitePro 560/570 20 x 11.5 x 8 inches (51 x 29 x 20 cm)
Unpacked 20 lbs. (8.8 kg)
As shipped 30 lbs (12.7 kg)
* Maximum operating temperature depends on altitude. At 8,000 ft, the maximum temperature is 31°C. At 9,000 ft (2743m), the maximum temperature is 30°C. At 10,000 ft (3048m), the maximum temperature is 29°C.

Contact your In Focus dealer to order. Refer to the In Focus Accessories Catalog for additional items.
Read Me First card 009-0124-xx
LitePro 560/570 User’s Guide 010-0060-xx
LiteShow II User’s Guide 010-0061-xx
Soft Carry Case 110-0079-xx
ATA-Approved Hard Carry Case 591-0169-xx
LitePro (VGA) Cable 210-0014-xx
North American Power Cord 210-0023-xx
Australian Power Cord 210-0027-xx
UK Power Cord 210-0028-xx
European Power Cord 210-0029-xx
Danish Power Cord 210-0030-xx
Swiss Power Cord 210-0031-xx
Projection Lamps, 36V, 400W (set of 2) 232-0020-xx
Mac Adapters (set of 2) 516-0003-xx
Remote Control Programmer User’s Guide 010-0083-xx
Remote Control Programmer Software 599-0064-xx
Remote Control Programmer (RS-232) Cable 210-0055-xx
Remote Control Programmer (RS-232) Adapter 515-0025-xx
RCA jack-to-mini plug adapter 515-0034-xx
LitePro Ceiling Mount Kit 591-0098-xx
LiteShow Demo Disk 599-0063-xx
LiteShow System Disk 599-0062-xx
Fuse, 10A, 3AB (use w/110V) 749-0013-xx
Fuse Holder for 10A, 3AB Fuse (use w/110V) 749-0014-xx
Fuse, 6.3A, 5x20mm (use w/220V) 749-0010-xx
Fuse Holder for 6.3A, 5x20mm Fuse (use w/220V) 749-0011-xx

The Y-shaped LitePro cable that shipped with your LitePro has three connectors, they are labeled “Monitor”, “Computer” and “LCD.” The pin assignments for these connectors are listed here.
The end of the LitePro cable that plugs into the LitePro itself is a male 26-pin D-style connector. The table below lists its pin assignments.
Input Pin Signal Description Output Pin
1 Vertical sync 10
2 Horizontal sync 11
8 Blue analog 14
9 Red analog 15
18 Green analog 5
21 GND
22 GND
23 Digital/analog video cable ID
25 VGA/no video cable ID pin

“Monitor” and “VGA” Connectors
The pin assignments are the same for the “Monitor” and “VGA” connectors. The “Monitor” connector is a female video RGB, 15-pin micro-D-style connector. The “VGA” connector is a male video RGB, 15-pin micro-D-style connector. The table below lists the pin assignments for both connectors.
1 Red analog input
2 Green analog input with composite sync
3 Blue analog input
5 GND
9 NC
11 GND
12 NC
13 Horizontal sync/composite sync input
14 Vertical sync input

The LitePro 560/570 connects to a laptop computer through the computer’s external monitor port. Most laptop computers do not automatically activate their external monitor port when a device such as the LitePro is connected. The following chart lists the commands that activate the external monitor port for a variety of computers. If your computer is not listed here, refer to your computer’s documentation.
Key command to activate port
Key command to de-activate port
Acer Ctrl-Alt-Esc (for setup)< Ctrl-Alt-Esc (for setup)
AST FN-D or Ctrl-D FN-D or Ctrl-D
type from A:/IVGA/CRT type from A:/IVGA/CRT
setup VGA/Conf.Simulscan setup VGA/Conf.Simulscan
Amrel* ** setup menu setup menu
Apple see Mac Portable and Mac PowerBook
BCC automatic - no activation command needed
Bondwell LCD or CRT option LCD or CRT option
Chaplet** setup screen setup screen
Data General Ctrl-Alt-Command Ctrl-Alt-Command
2 CRT/X at DOS prompt reboot
Dolch dip switch to CRT dip switch to LCD
Epson dip switch to CRT dip switch to LCD

Key command to activate port
Key command to de-activate port
Everex** setup screen option setup screen option
Gateway 2000 FN-F1 FN-F1
Grid* ** FN-F2, choose auto or simultaneous

140, 145, 170 no video port: requires a 3rd-party interface
230 requires Apple Docking Station

NEC* setup screen option setup screen option
CRT at the DOS prompt LCD at the DOS prompt
Packard Bell* FN-F2 FN-F2

Sharp dip switch to CRT dip switch to LCD
Tandy* ** Ctrl-Alt-Insert Ctrl-Alt-Insert
setup screen option setup screen option
Texas Instruments setup screen option setup screen option
Top-Link* ** setup screen option setup screen option
Toshiba* ** Ctrl-Alt-End Ctrl-Alt-Home

Key command to activate port
Key command to de-activate port
setup screen option setup screen option
Wyse software driver software driver
* These manufacturers have other models that automatically send video to the external CRT port when some type of display device is attached.
** These manufacturers offer more than one activation command depending on the computer model.
Appendix · Computer · Zenith FN-F10 FN-F10









In Focus Systems Inc. (“In Focus”) warrants that each LitePro 560 and LitePro 570 (“the Product”) sold hereunder will conform to and function in accordance with the written specifications of In Focus. Said limited warranty shall apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale. Said warranty shall continue for a period of one (1) year from the date of such purchase. In Focus does not warrant that the Product will meet the specific requirements of the first person or entity that purchases the Product for personal or business use. In Focus’ liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the Product or refund of the purchase price of the Product, at In Focus’ sole option. To exercise the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and expense, to In Focus or to any authorized In Focus service center provided, however, that the Product must be accompanied by a written letter explaining the problem and which includes (i) proof of date of purchase; (ii) the dealer’s name; and (iii) the model and serial number of the Product. A return authorization number, issued by the In Focus customer service department, must also be clearly displayed on the outside of the shipping carton containing the Product.
In Focus shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations, or service other than by In Focus or its authorized agents, causes other than from ordinary use or failure to properly use the Product in the application for which said Product is intended.
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY IN FOCUS.
IT IS UNDERSTOOD AND AGREED THAT IN FOCUS’ LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL IN FOCUS BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING IN FOCUS’ LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED.

010-0060-05

27700B SW Parkway Avenue Wilsonville, Oregon 97070-9215
NL-2132 HL Hoofddorp, The Netherlands
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.