EN
InFocus logo
Official user manual

InFocus LP220

86 pages·1.6 MB·Projector·PDF·ENDEFRITNLJA
InFocus LP220
Table of Contents 53 sections Table of Contents · Safety Summary · Introduction · Image Resolution · … ShowHide
Table of Contentsp.6Safety Summaryp.8Introductionp.12Image Resolutionp.12Compatibilityp.13Unpacking the Projectorp.13Usage Guidelinesp.15If You Need Assistancep.15Warrantyp.15Setting up the Projectorp.17Connecting the CableWizard to the Projectorp.18Selecting Connectors on the CableWizardp.18Preparing to Connect Your Equipment to the Project...p.20Connecting an IBM-Compatible Desktop Computerp.21Connecting an IBM-Compatible Laptop Computerp.23Connecting a Macintosh Desktop Computerp.25Connecting an Apple PowerBook Computerp.27Connecting a Video Playerp.29Connecting an External Speaker and a Subwooferp.31Connecting a Microphonep.32Connecting a PS/2-Compatible Mousep.32Connecting the Remote Control Cablep.33Powering up the Projector and Adjusting the Imagep.33Turning Off the Projectorp.35Using the Projectorp.37Basic Image Adjustmentp.37Using the Remote Controlp.37Adjusting the Projectorp.38Using the Remote and Keypad Buttonsp.40Using the Disk Mousep.44Using the On-Screen Menusp.44Display Menu Functionsp.45Audio Menu Functionsp.47Image Menu Functionsp.49Controls Menu Functionsp.51Maintenancep.54Cleaning the Lensp.54Removing and Replacing a Lensp.54Using the Zoom Lensp.55Replacing the Projection Lampp.56Resetting the Lamp Monitor Lightp.58Replacing the Batteries in the Remote Controlp.58Replacing the Fusep.58Using the Kensington Lockp.60Troubleshootingp.62Solutions to Common Problemsp.63Appendixp.68Specificationsp.68Accessoriesp.70Portable and Laptop Activation Chartp.72Using Video Mirroring with a PowerBook Computerp.76Projected Image Sizep.77Indexp.80
Page 1 of the InFocus LP220 user manual — USER’S
Page 1 · click to enlarge
Page 1
InFocus LP220 diagram (page 1)
Fig. 1

USER’S

GUIDE

Page 2 of the InFocus LP220 user manual — User’s Guide
Page 2 · click to enlarge
Page 2
InFocus LP220 diagram (page 2)
Fig. 2

User’s Guide

Page 3 of the InFocus LP220 user manual
Page 3 · click to enlarge
Page 3

Copyright © 1996 by In Focus Systems, Inc.

Wilsonville, Oregon. All rights reserved.

Page 4 of the InFocus LP220 user manual
Page 4 · click to enlarge
Page 4

FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to pro- vide reasonable protection against harmful interference in a residential installa- tion.

DOC (Canada) This Class B digital apparatus meets all requirements of the Canadian Interfer- ence-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.

Instructions to User This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter- ference to radio communications. However, there is no guarantee that interfer- ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Any and all modifications to this unit other than those made by approved service personnel are prohibited.

Safety Certifications UL, CUL, and TÜV

Trademarks Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc. MicroSaver and Kensington are trademarks or registered trademarks of Kensington Microware Limited. JBL is a trademark or registered trademark of Harman Interantional. Windows is a trademark or regis- tered trademark of Microsoft Corporation. CableWizard, In Focus Systems and LitePro are trademarks or registered trademarks of In Focus Systems, Inc.

Icon copyrighted by and used with the permission of Apple Computer, Inc. All Rights Reserved.

Page 5 of the InFocus LP220 user manual
Page 5 · click to enlarge
Page 5

Declaration of Conformity Manufacturer: In Focus Systems, Inc. 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Plantenweg 91, 2132 HL Hoofddorp, The Netherlands

We declare under our sole responsibility that the LitePro 210 and 220 LCD Projec- tors conform to the following directives and norms:

Directive 89/336/EEC EMIEN 55022 (1992) Class B EMC: EN 50082-1 (1992)

IEC 801-2, IEC 801-3, IEC 801-4 Directive 73/23/EEC Safety: EN 60950: 1992 + A1 + A2 + A3: 1995

May, 1996

Page 6 of the InFocus LP220 user manual — Table of Contents
Page 6 · Contents
Contents

Contents

Table of Contentsp.6Safety Summaryp.8Introductionp.12Image Resolutionp.12Compatibilityp.13Unpacking the Projectorp.13Usage Guidelinesp.15If You Need Assistancep.15Warrantyp.15Setting up the Projectorp.17Connecting the CableWizard to the Projectorp.18Selecting Connectors on the CableWizardp.18Preparing to Connect Your Equipment to the Project...p.20Connecting an IBM-Compatible Desktop Computerp.21Connecting an IBM-Compatible Laptop Computerp.23Connecting a Macintosh Desktop Computerp.25Connecting an Apple PowerBook Computerp.27Connecting a Video Playerp.29Connecting an External Speaker and a Subwooferp.31Connecting a Microphonep.32Connecting a PS/2-Compatible Mousep.32Connecting the Remote Control Cablep.33Powering up the Projector and Adjusting the Imagep.33Turning Off the Projectorp.35Using the Projectorp.37Basic Image Adjustmentp.37Using the Remote Controlp.37Adjusting the Projectorp.38Using the Remote and Keypad Buttonsp.40Using the Disk Mousep.44Using the On-Screen Menusp.44Display Menu Functionsp.45Audio Menu Functionsp.47Image Menu Functionsp.49Controls Menu Functionsp.51Maintenancep.54Cleaning the Lensp.54Removing and Replacing a Lensp.54Using the Zoom Lensp.55Replacing the Projection Lampp.56Resetting the Lamp Monitor Lightp.58Replacing the Batteries in the Remote Controlp.58Replacing the Fusep.58Using the Kensington Lockp.60Troubleshootingp.62Solutions to Common Problemsp.63Appendixp.68Specificationsp.68Accessoriesp.70Portable and Laptop Activation Chartp.72Using Video Mirroring with a PowerBook Computerp.76Projected Image Sizep.77Indexp.80
Page 8 of the InFocus LP220 user manual — SAFETY SUMMARY
Page 8 · click to enlarge
Page 8

SAFETY SUMMARY

Please read these instructions carefully before using your LitePro 210 or 220. Failure to comply with them could result in fire, elec- trical shock, personal injury or damage to equipment.

These graphics are used throughout this manual to draw your attention to important information about the projectors.

These graphics are used on LitePro labels.

safety information.

Hot Surfaces - Avoid touching hot surfaces. Do not

touch until the LitePro has cooled.

Lamp Explosion Hazard - If you continue to use the

lamp after the lamp monitor light comes on, it may explode, severely damaging your LitePro. Be sure to replace the lamp when the lamp monitor light comes on as described in this User’s Guide. Refer to the section titled “Replacing the Projection Lamp” for information about changing the bulb.

Do Not Look Into The Lens! Be extremely careful not to look into the projection lens when the LitePro is turned on. The bright light may harm your eyes. Be especially careful to keep children from looking into the lens.

Page 9 of the InFocus LP220 user manual — Safety Summary
Page 9 · click to enlarge
Page 9

S a f e t y S u m m a r y

Power Source Use only a three-wire grounding type power source. The power source should not exceed 250 volts rms between the supply con- ductors or between either conductor and the ground.

Power Cord Use only the power cord that was shipped with the LitePro. Although other power cords might be similar in appearance, they have not been safety-tested with the 210 or 220. Do not use a power cord if it has become damaged or frayed. Contact your In Focus dealer or call In Focus if you need to replace your power cord.

Grounding The projector is grounded through the grounding conductor on the power cord. To avoid electric shock, plug the power cord into a properly wired receptacle. Do not defeat the purpose of the grounding-type plug.

Fuse For continued protection against the risk of fire, use only the specified fuse. It must be a time delay, high breaking capacity 5x20mm fuse with the following amperages: for 6.3amp use T6.3AH, for 8amp use T8AH. Refer to page 55 for more informa- tion about fuse specifications and to page 45 for instructions on replacing the fuse.

the projection bulb when the lamp

monitor light comes on as

Lamp To avoid overheating and unacceptable image quality, replace the projection lamp with a lamp of the specified type. Refer to page 56 for lamp specifications and to page 43 for instructions on replacing the lamp.

described on page 43. If the lamp

remains in use too long, there is a

happens, your LitePro will be

severely damaged.

Lamp Compartment To avoid burns or an explosion hazard, do not open the lamp module door until the projector is turned off and the lamp has cooled. The hot lamp contains high pressure and can explode if damaged or old. Follow the instructions in this manual for lamp replacement carefully.

Page 10 of the InFocus LP220 user manual — Safety Summary
Page 10 · click to enlarge
Page 10

Hot Surfaces Allow the projector to cool at least 45 minutes before replacing a lamp. When you open the lamp housing, be very careful not to touch the hot surfaces inside.

Ventilation and Overheating Openings in the projector case provide ventilation to protect it from overheating. Keep loose papers and other objects well away from the bottom, top and side grills. Do not place the projector on top of or close to a computer or other heat-producing equipment.

Liquid Spills Do not set drinks on top of the projector. Spilled liquids can flow inside and cause damage.

Do Not Disassemble All LitePro service must be performed by an authorized In Focus service center. The only user-serviceable part in the LitePro is the projection lamp, which you can replace by opening the lamp cover on the bottom of the projector (see page 43). Do not open any other part of the LitePro. If your LitePro needs repair, call In Focus Technical Support as described on page 4. Before you call Technical Support, you may want to refer to “Troubleshooting” starting on page 49 to see if you can resolve the problem yourself.

case, you will void the warranty.

Don’t Set the LitePro on its Lens To protect the lens when you are transporting the LitePro, adjust the lens so it is fully retracted (turn it clockwise) before you pack it.

Place the LitePro in its carrying case with the lens facing upwards. You may damage the LitePro if you set it on its lens.

Page 11 of the InFocus LP220 user manual — Introduction
Page 11 · click to enlarge
Page 11

Introduction

Page 12 of the InFocus LP220 user manual — Image Resolution
Page 12 · click to enlarge
Page 12

INTRODUCTION

The In Focus Systems LitePro® 210 and 220 multimedia projec- tors combine powerful and sophisticated features with easy-to- use, intuitive controls. Built-in multimedia features include audio by JBL™, a palette of 16.7 million colors and active matrix liquid crystal display (LCD) technology. The 200 series projectors are ideal for high-performance business, training and imaging appli- cations that demand exceptional color quality. The 210 has VGA graphics, the 220 has SVGA graphics. The user interfaces of the two products are identical; information in this User’s Guide applies to both products.

Image Resolution

LitePro 210 The VGA resolution of the 210’s projected image is 640x480. It displays computer images just as they appear on your com- puter’s monitor. Screen resolutions between 640x480 and 800x600 are compressed to 640x480. The 210 cannot compress screen reso- lutions above 800x600. If your computer’s screen resolution is higher than 800x600, reset it to a lower resolution before you con- nect the 210.

The SVGA resolution of the 220’s projected image is 800x600. It displays computer images just as they appear on your com- puter’s monitor. Screen resolutions between 800x600 and 1024x768 are compressed to 800x600. The 220 cannot compress screen resolutions above 1024x768. If your computer’s screen res- olution is higher than 1024x768, reset it to a lower resolution before you connect the 220.

expands 640x480 images to

800x600. You can display these

images at 640x480 by turning off

the Auto Resize feature. See “Auto

Resize” on page 37 for more

information.

LitePro 220

Page 13 of the InFocus LP220 user manual — Unpacking the Projector
Page 13 · click to enlarge
Page 13

I n t r o d u c t i o n

Compatibility

The projector is compatible with a wide variety of computers and video devices, including:

  • IBM-compatible computers, including laptops, up to 800x600 resolution (LitePro 210) or 1024x768 resolution (LitePro 220) at 75Hz.
  • IBM PS/2 in VGA and MCGA modes.
  • Apple Macintosh and PowerBook computers up to 800x600 resolution (LitePro 210) or 1024x768 resolution (LitePro 220).
  • Various VCRs, camcorders and laser disc players.

The projector is not compatible with these systems:

  • IBM-compatible computers in CGA or EGA graphics mode.
  • Macintosh 128, 512, Plus, SE, SE/30 or Classic.

Unpacking the Projector

The projector comes with the items shown in Figure 1. Check to make sure all are included. Contact your In Focus dealer immedi- ately if anything is missing.

If you are experienced in setting up presentation systems, use the LitePro 210/220 Quick Start card that was included in the shipping box. For complete details on connecting and operating the projec- tor, refer to this User’s Guide.

shipping box may vary depending

on the LitePro configuration you’ve

ordered.

Page 14 of the InFocus LP220 user manual — Compatibility
Page 14 · click to enlarge
Page 14
InFocus LP220 — Compatibility diagram (page 14)
Fig. 3 · Compatibility
1. LitePro 210 or 220 projector 6. RCA audio/video (A/V) cable
2. LitePro 210/220 User’s Guide 7. CableWizard
3. power cord 8. CableWizard computer cable
4. remote and batteries 9. CableWizard mouse cable
5. lens cap 10. CableWizard audio cable
Not shownQuick Start card, remote cable

Shipping box contents

Page 15 of the InFocus LP220 user manual — Warranty
Page 15 · click to enlarge
Page 15

I n t r o d u c t i o n

Usage Guidelines

  • Do not look directly into the projection lens when the projector is turned on. The bright light may harm your eyes.
  • The top and bottom of the projector can be very hot to the touch after use. Use extreme care or let it cool before lifting it.
  • Do not block the grills at the front or top of the projector. Restricting the air flow can cause it to overheat and turn off.

and turns off, you must wait about

  • Handle the projector as you would any product with glass components. Be especially careful not to drop it.

45 seconds before you attempt to

turn it back on.

  • Avoid leaving the projector in direct sunlight or extreme cold for extended periods of time. If this happens, allow it to reach room temperature before use.
  • Transport the projector in a vendor-approved hard or soft case. Part numbers for these cases are listed on page 57. Call your In Focus dealer to order.

If You Need Assistance

The first place to look for help is in this manual. Be sure to check the guidelines in “Troubleshooting” on page 49.

If this manual doesn’t answer your question, call your In Focus dealer. You can also call In Focus Customer Service directly at 1-800-799-9911. Call between 6 a.m. and 5 p.m. PST, Monday through Friday. In Europe, call In Focus in The Netherlands at (31) 23-5623200. In Singapore, call (65) 334-9005. Or, send us an e-mail at techsupport@infs.com.

The In Focus World Wide Web address is http://www.infs.com.

Warranty

These products are backed by a limited one-year warranty. The details of the warranty are printed at the back of this manual. Longer term warranties can be purchased from your In Focus dealer. Refer to page 58 for part numbers.

Page 16 of the InFocus LP220 user manual — Setting up the
Page 16 · click to enlarge
Page 16

Setting up the

Projector

Page 17 of the InFocus LP220 user manual — SETTING UP THE PROJECTOR
Page 17 · click to enlarge
Page 17

SETTING UP THE PROJECTOR

1 Place the projector on a flat surface.

  • The projector must be within 10 feet of your power source and within 10 feet of your computer.
  • If you want to project from behind a translucent screen, set up the projector behind your screen. See “Rear Projection” on page 40 to reverse the image.

cable, sold separately, lets you

  • If you are installing the projector on the ceiling, refer to the LitePro 200 Series Ceiling Mount Installation Guide for more information. To turn the image upside down, see “Ceiling” on page 39. The Ceiling Mount Kit is sold separately; see page 58.

increase the distance between the

projector and your computer to 50

feet. See “Accessories” on

page 57.

2 Position the projector the desired distance from the screen.

  • The distance from the lens of the projector to the screen determines the size of the projected image. Figure 2 shows three projected image sizes using the varifocal lens or the zoom lens at minimum focusing distance. For more information about image size, see “Projected Image Size” on page 64.

3 Make sure the projector and your computer are turned off.

InFocus LP220 — SETTING UP THE PROJECTOR diagram (page 17)
Fig. 4

Projected image size (varifocal lens, zoom lens at minimum focusing distance)

Page 18 of the InFocus LP220 user manual — Selecting Connectors on the CableWizard
Page 18 · click to enlarge
Page 18

S e t t i n g u p t h e P r o j e c t o r

Connecting the CableWizard to the Projector

The CableWizard simplifies the connection process by providing a central hub for all the connections between the projector and your computer. The connectors on the CableWizard are labeled with icons.

Connect the end of the CableWizard cord to the connector on the projector’s connector panel (Figure 3).

InFocus LP220 — Connecting the CableWizard to the Projector diagram (page 18)
Fig. 5 · Connecting the CableWizard to the Projector

computer, monitor and projector

whenever you connect or

disconnect cables.

Connecting the CableWizard cable to the projector

Selecting Connectors on the CableWizard

Turn the selector on the top of the CableWizard to reveal the correct connectors for your computer.

InFocus LP220 — Selecting Connectors on the CableWizard diagram (page 18)
Fig. 6 · Selecting Connectors on the CableWizard

Selecting connectors on the CableWizard

Page 19 of the InFocus LP220 user manual — Connecting the CableWizard to the Projector
Page 19 · click to enlarge
Page 19
  • If you’re connecting an IBM-compatible desktop or laptop computer , turn the selector until the window displays “PC.”
InFocus LP220 — Connecting the CableWizard to the Projector diagram (page 19)
Fig. 7 · Connecting the CableWizard to the Projector

cables before turning the selector

on the CableWizard.

Selecting the IBM-compatible connectors on the CableWizard

  • If you’re connecting a Macintosh desktop or an Apple PowerBook computer , turn the selector until the window displays “Mac™.”
InFocus LP220 — Connecting the CableWizard to the Projector diagram (page 19)
Fig. 8 · Connecting the CableWizard to the Projector

Selecting the Macintosh connectors on the CableWizard

Show 5 more labels / short text on this page
computer · monitor · audio · monitor · audio
Page 20 of the InFocus LP220 user manual — Preparing to Connect Your Equipment to the Projector
Page 20 · click to enlarge
Page 20

S e t t i n g u p t h e P r o j e c t o r

Preparing to Connect Your Equipment to the Projector

Now you’re ready to connect your equipment. Computers are connected to the Cable Wizard. Video players and other equip- ment, such as external speakers, are connected directly to the projector.

Steps for connecting the different types of equipment are given on the pages listed below.

make sure the projector and your

equipment are turned off. If you’re

Equipment you want to connect Page

connecting a computer, make sure

IBM-compatible desktop computer page 9

the distance between it and the

IBM-compatible laptop computer page 11

projector is 10 feet or less and

Macintosh desktop computer page 13

you’ve selected the appropriate

Apple PowerBook page 15

connectors on the CableWizard.

Video player page 17

External speakers or subwoofer page 19

PS/2-compatible mouse page 20

Remote control cable page 20

Microphone page 20

Page 21 of the InFocus LP220 user manual — Connecting an IBM-Compatible Desktop Computer
Page 21 · click to enlarge
Page 21

Connecting an IBM-Compatible Desktop Computer

1 Locate the cable that connects your monitor to your computer. Unplug it from the computer.

2 Plug the end of the CableWizard computer cable into the monitor connector on your computer.

3 Plug the end of the computer cable into the connector on the CableWizard.

InFocus LP220 — Connecting an IBM-Compatible Desktop Computer diagram (page 21)
Fig. 9 · Connecting an IBM-Compatible Desktop Computer

Connecting the CableWizard computer cable to an IBM-compatible desktop computer

Do you want to display the image on your computer’s monitor as well as on the projection screen?

1 Plug your monitor’s cable into the connector on the CableWizard.

Do you want to play your computer’s audio on the projector?

1 Unplug the audio cable, if present, from your computer.

2 Plug either end of the CableWizard audio cable into the audio connector on your computer.

3 Plug the other end of the audio cable into the connector on the CableWizard.

Page 22 of the InFocus LP220 user manual — Connecting an IBM-Compatible Desktop Computer
Page 22 · click to enlarge
Page 22

S e t t i n g u p t h e P r o j e c t o r

Do you want to control your computer’s mouse from the projector’s remote or keypad?

1 Unplug the mouse cable from your computer.

2 Plug the end of the CableWizard mouse cable into the mouse connector on your computer.

3 Plug the end of the CableWizard mouse cable into the connector on the CableWizard.

InFocus LP220 — Connecting an IBM-Compatible Desktop Computer diagram (page 22)
Fig. 10 · Connecting an IBM-Compatible Desktop Computer

Connecting the CableWizard monitor, audio and mouse cables to an IBM-compatible desktop computer

Now you’re ready to power up the projector and your computer. Skip to “Powering up the Projector and Adjusting the Image” on page 21.

audio cable

Page 23 of the InFocus LP220 user manual — Connecting an IBM-Compatible Laptop Computer
Page 23 · click to enlarge
Page 23

Connecting an IBM-Compatible Laptop Computer

1 Plug the end of the CableWizard computer cable into the video connector on your computer.

2 Plug the end of the CableWizard computer cable into the

connector on the CableWizard.

do not automatically turn on their

external video port when a second-

InFocus LP220 — Connecting an IBM-Compatible Laptop Computer diagram (page 23)
Fig. 11 · Connecting an IBM-Compatible Laptop Computer

ary display device such as a projec-

tor is connected. Refer to your

computer manual for the com-

mand that activates the external

video port. Activation commands

for some laptop computers are

listed in the Appendix of this

manual on page 59.

Connecting the CableWizard computer cable to an IBM-compatible laptop computer

Do you want to play your computer’s audio on the projector?

1 Plug either end of the CableWizard audio cable into the audio connector on your computer.

mouse control, you can use the

CableWizard Lite. CableWizard

2 Plug the other end of the audio cable into the connector on the CableWizard.

Lite is ordered separately. See

“Accessories” on page 57.

Page 24 of the InFocus LP220 user manual — Connecting an IBM-Compatible Laptop Computer
Page 24 · click to enlarge
Page 24

S e t t i n g u p t h e P r o j e c t o r

Do you want to control the computer’s mouse from the projector’s remote or keypad?

1 Locate the mouse cable and unplug it from your computer.

2 Plug the end of the CableWizard mouse cable into the mouse connector on your computer.

3 Plug the end of the CableWizard mouse cable into the connector on the CableWizard.

InFocus LP220 — Connecting an IBM-Compatible Laptop Computer diagram (page 24)
Fig. 12 · Connecting an IBM-Compatible Laptop Computer

Connecting the CableWizard audio and mouse cables to an IBM-compatible laptop computer

Now you’re ready to power up the projector and your laptop. Skip to “Powering up the Projector and Adjusting the Image” on page 21.

audio cable

Page 25 of the InFocus LP220 user manual — Connecting a Macintosh Desktop Computer
Page 25 · click to enlarge
Page 25

Connecting a Macintosh Desktop Computer

1 Locate the cable that connects the monitor to your computer. Unplug it from the computer.

2 Plug the end of the CableWizard computer cable into the monitor connector on your computer.

3 Plug the end of the CableWizard computer cable into the

connector on the CableWizard.

InFocus LP220 — Connecting a Macintosh Desktop Computer diagram (page 25)
Fig. 13 · Connecting a Macintosh Desktop Computer

Connecting the CableWizard computer cable to a Macintosh desktop computer

Do you want to display the image on your computer’s monitor as well as on the projection screen?

1 Plug the monitor’s cable into the connector on the CableWizard.

Do you want to play your computer’s audio on the projector?

1 Unplug the audio cable, if present, from your computer.

2 Plug either end of the CableWizard audio cable into the audio connector on your Macintosh.

3 Plug the other end of the audio cable into the connector on the CableWizard.

Page 26 of the InFocus LP220 user manual — Connecting a Macintosh Desktop Computer
Page 26 · click to enlarge
Page 26

S e t t i n g u p t h e P r o j e c t o r

Do you want to control the computer’s mouse from the projector’s remote or keypad?

1 Unplug the mouse from your Macintosh or locate an unused ADB connector.

2 Plug the end of the CableWizard mouse cable into the

mouse connector or the (ADB) connector on your Macintosh.

3 Plug the end of the CableWizard mouse cable into the connector on the CableWizard.

InFocus LP220 — Connecting a Macintosh Desktop Computer diagram (page 26)
Fig. 14 · Connecting a Macintosh Desktop Computer

Connecting the CableWizard monitor, audio and mouse cables to a Macintosh desktop computer

Now you’re ready to power up the projector and the Macintosh. Skip to “Powering up the Projector and Adjusting the Image” on page 21.

audio cable

Page 27 of the InFocus LP220 user manual — Connecting an Apple PowerBook Computer
Page 27 · click to enlarge
Page 27

Connecting an Apple PowerBook Computer

1 Plug the end of the CableWizard computer cable into the video connector on your PowerBook.

2 Plug the end of the CableWizard computer cable into the

connector on the CableWizard.

require the Apple-supplied video-

3 If you want the projector display to be the same as the Power- Book’s screen display, turn on video mirroring. (See “Using Video Mirroring with a PowerBook Computer” on page 63 for additional information.)

out cable for external video. Con-

nect it between the PowerBook

and the CableWizard computer

cable as shown in Figure 13.

InFocus LP220 — Connecting an Apple PowerBook Computer diagram (page 27)
Fig. 15 · Connecting an Apple PowerBook Computer

Connecting the CableWizard computer cable to an Apple PowerBook

Do you want to play your computer’s audio on the projector?

1 Plug either end of the CableWizard audio cable into the audio connector on your PowerBook.

2 Plug the other end of the audio cable into the connector on the CableWizard.

Page 28 of the InFocus LP220 user manual — Connecting an Apple PowerBook Computer
Page 28 · click to enlarge
Page 28

S e t t i n g u p t h e P r o j e c t o r

Do you want to control the computer’s mouse from the projector’s remote or keypad?

1 Locate the mouse cable and unplug it from your PowerBook.

2 Plug the end of the CableWizard mouse cable into the (ADB) connector on your PowerBook.

3 Plug the end of the CableWizard mouse cable into the connector on the CableWizard.

InFocus LP220 — Connecting an Apple PowerBook Computer diagram (page 28)
Fig. 16 · Connecting an Apple PowerBook Computer

Connecting the CableWizard audio and mouse cables to a PowerBook

Now you’re ready to power up the projector and your Power- Book. Skip to “Powering up the Projector and Adjusting the Image” on page 21.

computer cable

Page 29 of the InFocus LP220 user manual — Connecting a Video Player
Page 29 · click to enlarge
Page 29

Connecting a Video Player

1 If your video player uses a round, one-prong composite video connector, you’ll need only the A/V cable that shipped with the projector.

  • If your video player uses a round, four-prong S-video connector, you’ll need an S-video cable in addition to the A/V cable. The S-video cable is sold separately. (See “Accessories” on page 57.)

2 Plug the A/V cable’s yellow connector into the “video-out” port on your video player (Figure 15). This port may be labeled “To Monitor.”

  • If you’re using an S-video cable, connect it to the “s-video out” connector on the video player (Figure 16).

3 Plug the other yellow connector into the composite connector on the back of the projector.

  • If you’re using S-video, plug the other end of the cable into the “s-video” connector on the projector (Figure 16).
InFocus LP220 — Connecting a Video Player diagram (page 29)
Fig. 17 · Connecting a Video Player

Connecting the projector to a video player using the standard A/V cable (with composite

audio/video cable · video connector)

Page 30 of the InFocus LP220 user manual — Connecting a Video Player
Page 30 · click to enlarge
Page 30

S e t t i n g u p t h e P r o j e c t o r

InFocus LP220 — Connecting a Video Player diagram (page 30)
Fig. 18 · Connecting a Video Player

A/V cable S-video cable

Connecting the projector to a video player using an S-video cable and the audio con- nectors on the standard A/V cable

4 Plug the A/V cable’s white connector into the left “audio out” port on your video player. Plug the cable’s red connector into the right “audio out” port on the video player (Figure 15 and Figure 16).

  • If you’re using an S-video cable, the yellow connectors on the A/V cable remain unused (Figure 16).

may also have a “Video Out” port

5 Plug the A/V cable’s other white and red connectors to the left and right “audio in” ports on the projector.

for a coaxial cable connection.

DO NOT use this to connect to the

The projector is compatible with the three major broadcast video standards: NTSC, PAL and SECAM. It automatically adjusts to optimize its performance for the incoming video. You can also set the video standard manually from the projector’s Controls menu; see “Video Standard” on page 39.

projector.

Page 31 of the InFocus LP220 user manual — Connecting an External Speaker and a Subwoofer
Page 31 · click to enlarge
Page 31

Connecting an External Speaker and a Subwoofer

  • To connect one or two external speakers, plug the speaker

cables into the two (audio out) connectors on the projector.

  • To connect a subwoofer, plug the subwoofer cable into the connector on the projector.

must be amplified.

InFocus LP220 — Connecting an External Speaker and a Subwoofer diagram (page 31)
Fig. 19 · Connecting an External Speaker and a Subwoofer

Connecting an external speaker and a subwoofer

speaker cable

Page 32 of the InFocus LP220 user manual — Connecting a PS/2-Compatible Mouse
Page 32 · click to enlarge
Page 32

S e t t i n g u p t h e P r o j e c t o r

Connecting a Microphone

  • To connect a microphone to the projector, plug the microphone

cable into the connector on the projector.

InFocus LP220 — Connecting a Microphone diagram (page 32)
Fig. 20 · Connecting a Microphone

source volume at its lowest level

when installing the microphone.

For information about setting the

microphone level, see page 35.

Connecting a PS/2-Compatible Mouse

  • To connect a PS/2-compatible mouse to the projector, plug the

mouse cable into the connector on the projector.

computer, monitor and the

InFocus LP220 — Connecting a PS/2-Compatible Mouse diagram (page 32)
Fig. 21 · Connecting a PS/2-Compatible Mouse

projector whenever you connect

the mouse. Power on the projector

first, then the computer.

The PS/2-compatible mouse connector on the projector

using the Scribble feature easier.

Connecting a microphone · PS/2-compatible mouse connector

Page 33 of the InFocus LP220 user manual — Powering up the Projector and Adjusting the Image
Page 33 · click to enlarge
Page 33

Connecting the Remote Control Cable

If the projector cannot receive the remote’s signal, as may be the case if you’re using rear projection, connect the remote directly to the projector with the remote cable.

1 Plug the end of the remote cable with the cylinder into the connector on the projector.

2 Plug the other end into the plug on the remote.

InFocus LP220 — Connecting the Remote Control Cable diagram (page 33)
Fig. 22 · Connecting the Remote Control Cable

Connecting the remote control cable

Powering up the Projector and Adjusting the Image

1 Remove the lens cap.

2 Plug the power cord into the projector (Figure 21), then plug it into your electrical outlet. A surge-protected power strip is recommended if power surges are common in your area.

cord that shipped with the

projector.

InFocus LP220 — Powering up the Projector and Adjusting the Image diagram (page 33)
Fig. 23 · Powering up the Projector and Adjusting the Image

Connecting the power cord to the projector

Page 34 of the InFocus LP220 user manual — Connecting the Remote Control Cable
Page 34 · click to enlarge
Page 34

S e t t i n g u p t h e P r o j e c t o r

3 Turn on the projector.

  • The power indicator and lamp module LEDs (Figure 22) light solidly while the projector initializes. The power LED blinks green when the projector begins to power up. When the projector reaches full power, the power LED lights solid green and the lamp LED goes out.

remains solidly lit after the LitePro

has powered on, the lamp needs

to be replaced. If the lamp

remains in use too long, it may

lamp module indicator LED

explode and severely damage the

InFocus LP220 — Connecting the Remote Control Cable diagram (page 34)
Fig. 24 · Connecting the Remote Control Cable

LitePro. Refer to “Replacing the

Projection Lamp” on page 43 for

more information.

video source indicator LED computer source indicator LED

4 If you connected a video player, turn it on.

  • Press the video button on the remote control or keypad to display the image from your video player. The video source indicator LED displays a solid green indicating the video source is active (Figure 22). Press computer to return to your computer’s image.
  • Use the volume buttons to adjust the volume.
  • If you don’t want to hear the sound from your video player, press the mute button.

5 If you connected any external speakers, turn them on.

6 If you connected your monitor, turn it on.

power/standby indicator LED · Indicator LEDs

Page 35 of the InFocus LP220 user manual — Turning Off the Projector
Page 35 · click to enlarge
Page 35

7 Turn on your computer.

  • The computer image should display on the projection screen.
  • The computer source indicator LED displays a solid green indicating the computer source is active (Figure 22).
  • If necessary, use the brightness buttons on the remote control or keypad to adjust the brightness. You can make further adjustments to the image from the projector’s onscreen menus. To open the menus, press the menu button on the remote control or keypad. Then select the Display menu or the Image menu. For more information about the menus, see page 32.

the order in which you power up

the equipment is very important.

We recommend that you always

turn on the computer LAST. Turn

  • If you don’t want to hear the sound from your computer or video player, press the mute button. (Pressing mute does not mute the microphone.)

on all other pieces of equipment

(including the computer’s moni-

tor) before you turn on the com-

Turning Off the Projector

puter.

If you want to turn off the projector for a short period of time, press the standby button on the remote control or keypad. This turns off the lamp but keeps the projector running. The power/ standby indicator LED (Figure 22) blinks green while the projec- tor is in standby. To exit standby mode, press the standby button once. (It takes several seconds for the projection lamp to reach full power and project the image again.)

To completely power off the projector, press the “O” side of the power switch. If you want to turn the projector back on immedi- ately, you must allow about 45 seconds for the lamp to cool. The lamp won’t light if it’s too hot.

projector after you have switched

it off, always remove the power

cord from the electrical outlet first,

then remove it from the projector.

Page 36 of the InFocus LP220 user manual — Using the
Page 36 · click to enlarge
Page 36

Using the

Projector

Page 37 of the InFocus LP220 user manual — Using the Remote Control
Page 37 · click to enlarge
Page 37

USING THE PROJECTOR

This section describes how to use and make adjustments to the projector. It also provides a reference to the remote control but- tons and the options available from the on-screen menus.

Basic Image Adjustment

1 Make sure you have powered up your equipment in the right order (page 21).

2 If the image doesn’t display completely, adjust the height of the projector (page 26) or center the image by adjusting its horizontal or vertical position (page 38).

3 If the image is out of focus, rotate the lens to focus it (page 26).

4 If the image appears to shimmer or if it has blurry vertical bars after you have adjusted the focus, turn Auto Image (page 37) off and then back on to reset the automatic sync and tracking. If that doesn’t clear up the image, adjust the sync (page 37) and/or the tracking (page 38) manually.

5 If the colors don’t look right, adjust the brightness (page 29).

Using the Remote Control

Point the remote control at the projection screen or at the front or rear of the projector. The range for optimum operation is about 40 feet. If you point the remote at the projection screen, the dis- tance to the screen and back to the projector must be less than or equal to 40 feet. For best results, point the remote directly at the front or the rear of the projector.

remote control at the projector so

that its signal is received — for

example, when using rear projec-

tion — connect the remote

directly to the projector with the

remote control cable (page 21).

Page 38 of the InFocus LP220 user manual — Adjusting the Projector
Page 38 · click to enlarge
Page 38

U s i n g t h e P r o j e c t o r

Adjusting the Projector

To focus the image, rotate the projection lens until the image is clear. Rotate the lens clockwise for a longer focusing distance; counterclockwise for a shorter focusing distance.

If the projected image seems wider at the bottom or at the top, rotate the keystone adjustment dial on the back of the projector until the image is correct (Figure 23).

InFocus LP220 — Adjusting the Projector diagram (page 38)
Fig. 25 · Adjusting the Projector

The projector is equipped with a self-locking, quick-release eleva- tor foot and a leveling knob.

InFocus LP220 — Adjusting the Projector diagram (page 38)
Fig. 26 · Adjusting the Projector

Quick-release elevator foot and leveling knob

Keystone adjustment knob

Page 39 of the InFocus LP220 user manual — Adjusting the Projector
Page 39 · click to enlarge
Page 39

To raise the projector:

1 Raise the front of the projector off the table by lifting up on the handle (Figure 25).

2 While holding the projector, press and hold the quick-release button (Figure 25).

3 When the projector is the height you want, release the button to lock the elevator foot into position.

4 If necessary, use the leveling knob (Figure 24) to adjust the angle of the projected image.

Adjusting the height of the projector

To lower the projector:

1 Hold the projector’s handle.

jector’s handle when you press the

2 Press the elevator’s quick release button.

elevator’s quick release button.

3 Lower the projector.

4 If necessary, use the leveling knob (Figure 24) to readjust the angle of the projected image.

Page 40 of the InFocus LP220 user manual — Using the Remote and Keypad Buttons
Page 40 · click to enlarge
Page 40

U s i n g t h e P r o j e c t o r

Using the Remote and Keypad Buttons

This section provides an alphabetical reference to the remote and keypad buttons.

InFocus LP220 — Using the Remote and Keypad Buttons diagram (page 40)
Fig. 27 · Using the Remote and Keypad Buttons
InFocus LP220 — Using the Remote and Keypad Buttons diagram (page 40)
Fig. 28 · Using the Remote and Keypad Buttons

Remote control · Keypad

Page 41 of the InFocus LP220 user manual — Using the Remote and Keypad Buttons
Page 41 · click to enlarge
Page 41

Brightness Adjusting the brightness lightens or darkens the image.

  • To darken the image, press
  • To lighten the image, press

The brightness buttons are auto-repeating; they repeat their func- tion as long as you hold down the button.

Computer When you have more than one source (computer or video) con- nected to the projector, select between them by pressing the but- ton for the source you want.

Press computer to display the computer image.

Freeze The freeze button halts, or “freezes” the projected image. Use this button to freeze a frame of video (the video continues to run but the projected image is frozen). You can also freeze an image from a computer source on the screen, allowing you to perform other operations on the computer without the audience seeing them. Press freeze again when you want the image to return to normal.

Help Press help to display the online help information.

Light Press light to illuminate the buttons on the remote control. The light goes off automatically 10 seconds after you press any button.

LiteShow The liteshow button will be used to display a LiteShow presenta- tion from disk. Call your In Focus dealer for availability.

Page 42 of the InFocus LP220 user manual — Using the Remote and Keypad Buttons
Page 42 · click to enlarge
Page 42

U s i n g t h e P r o j e c t o r

Menu Press menu to open the on-screen menus. Press menu again to close the menus. When you close the menus, the projector saves any changes you made. For more information about the on- screen menus, see page 32.

Pressing the mute button silences the internal speakers. It also silences any external speakers that are connected. It does not mute the microphone.

effect on microphone volume.

To return the volume to its previous setting, press mute again or press either volume button.

Scribble The scribble button activates on-screen annotation.

1 Press the scribble button. The cursor changes to a pencil.

2 Press the right disk mouse button (Figure 29) to display the color selector. Use the disk mouse to position the cursor on the desired color, then press the left mouse button. Press the right button again to close the color selector.

enhanced by using a PS/2 mouse.

See “Connecting a PS/2-

Compatible Mouse” on page 20.

3 Move the pencil to where you want to start the annotation.

4 Press the left mouse button. The cursor changes to an upright pencil.

5 Use the disk mouse (or PS/2 mouse, if connected) to draw your annotation. Press the left mouse button to complete the annotation.

6 To exit Scribble, press the scribble button. The annotation is automatically deleted (it cannot be saved).

Mute

Page 43 of the InFocus LP220 user manual — Using the Remote and Keypad Buttons
Page 43 · click to enlarge
Page 43

Standby When you press standby, the display and audio turn off and the screen becomes black. After 30 seconds the lamp goes out if you haven’t pressed any other buttons.

  • If you press any button again within 30 seconds, the projector returns to normal operations immediately.
  • If you press standby again after 30 seconds, there is about a 30second delay before the lamp turns back on.

Video When you have more than one source (computer or video) con- nected to the projector, select between them by pressing the but- ton for the source you want.

Press video to display the image from your video player.

  • To increase the volume, press
  • To decrease the volume, press

The volume buttons are auto-repeating; they continue to adjust the volume as long as you hold them down. Volume adjustments are saved for each source you have connected.

Volume

Page 44 of the InFocus LP220 user manual — Using the On-Screen Menus
Page 44 · click to enlarge
Page 44

U s i n g t h e P r o j e c t o r

Using the Disk Mouse

Press anywhere on the edge of the disk mouse to move the cursor on the screen. For example, if you press the top edge of the disk, the cursor moves up the screen; if you press the bottom edge, the cursor moves down (Figure 28). You can move the cursor at any angle by pressing the corresponding edge of the disk.

disk mouse often gets the best

results.

press here to move the cursor up

press here to move the cursor down

Using the disk mouse

Using the On-Screen Menus

The projector has four on-screen menus that allow you to make image adjustments and change a variety of settings. Most of these adjustments aren’t available directly from the remote or keypad.

To open the on-screen menus, press the menu button on the remote or keypad. Press menu again when you want to close the menus.

To select a menu, use the disk mouse to move the cursor to the tab for the menu you want, then click either mouse button.

left mouse right mouse button button

Disk mouse and mouse buttons

disk mouse

Page 45 of the InFocus LP220 user manual — Display Menu Functions
Page 45 · click to enlarge
Page 45

To change a menu setting, move the cursor to the setting you want to change, then use one of the two mouse buttons below the disk to make changes.

The status bar at the top of the menu display indicates the source that is currently active. For example, if you have both a computer and a video player connected, “Source: Computer” or “Source: Video” displays depending on whether you’ve pressed the com- puter or the video button on the remote or keypad.

InFocus LP220 — Display Menu Functions diagram (page 45)
Fig. 29 · Display Menu Functions

Display menu

Page 46 of the InFocus LP220 user manual — Display Menu Functions
Page 46 · click to enlarge
Page 46

U s i n g t h e P r o j e c t o r

Adjusting the brightness changes the intensity of the image.

  • Press the left mouse button to darken the image.
  • Press the right mouse button to lighten the image.

Contrast The contrast controls the degree of difference between the light- est and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.

using the menu is the same as

changing it using the remote or

keypad.

  • Press the left mouse button to decrease the contrast.
  • Press the right mouse button to increase the contrast, making the blacks appear blacker and the whites appear whiter.

Tint The Tint setting adjusts the red-green color balance in the pro- jected image. Changing the Tint setting has no effect on PAL or SECAM video sources.

  • Press the left mouse button to increase the amount of green in the image.
  • Press the right mouse button to increase the amount of red in the image.

Reset All Click either mouse button to reset all the options (except Lan- guage and Video Standard) in all the menus to their original set- tings. This also returns Freeze and Mute to their default (off) settings.

Brightness

Page 47 of the InFocus LP220 user manual — Audio Menu Functions
Page 47 · click to enlarge
Page 47

Audio Menu Functions

InFocus LP220 — Audio Menu Functions diagram (page 47)
Fig. 30 · Audio Menu Functions
  • Press the left mouse button to decrease the volume.
  • Press the right mouse button to increase the volume.

Volume adjustments you make are saved for each source.

Mic Volume • Press the right mouse button to increase the microphone volume.

from the menu is the same as

changing it using the remote or

  • Press the left mouse button to decrease the microphone volume.

keypad.

Balance The Balance setting controls the balance between the left and right external speakers. It appears gray and won’t highlight if you haven’t connected external speakers. The Balance setting applies to all sources you have connected.

  • Press the left mouse button to increase the amount of sound coming from the left external speaker.

Audio menu · Volume

Page 48 of the InFocus LP220 user manual — Audio Menu Functions
Page 48 · click to enlarge
Page 48

U s i n g t h e P r o j e c t o r

  • Press the right mouse button to increase the amount of sound coming from the right external speaker.

Fade The Fade setting controls the balance between the internal and external speakers. The setting appears gray and won’t highlight if external speakers aren’t connected.

  • Press the left mouse button to increase the amount of sound coming from the internal speakers.
  • Press the right mouse button to increase the amount of sound coming from the external speakers.

Treble The Treble setting controls the higher frequencies of your audio source.

  • Press the left mouse button to decrease the treble.
  • Press the right mouse button to increase the treble.

settings apply only to the

Bass The Bass setting controls the lower frequencies of your audio source.

projector’s internal speakers.

External speakers typically have

their own tone controls.

  • Press the left mouse button to decrease the bass.
  • Press the right mouse button to increase the bass.

Ambiance The Ambiance setting controls the spaciousness of the sound quality from the projector’s internal speakers.

  • Press the left mouse button to increase the amount of sound coming from the rear internal speaker.
  • Press the right mouse button to decrease the amount of sound coming from the top internal speaker.
Page 49 of the InFocus LP220 user manual — Image Menu Functions
Page 49 · click to enlarge
Page 49
InFocus LP220 — Image Menu Functions diagram (page 49)
Fig. 31 · Image Menu Functions

The projector automatically adjusts tracking, signal synchroniza- tion and vertical and horizontal position for most computers. If you want to adjust these features manually, you must turn off Auto Image first by clicking it.

fere withthe operation of Auto

Image. If you’re experiencing prob-

Auto Resize The Auto Resize setting is available only for computer sources. Auto Resize automatically resizes the image by scaling it up or down.

lems, try turning your screen saver

off, then turning Auto Image off

and back on.

When Auto Resize is on, the projector makes the best fit of the image to the screen. If you turn Auto Resize off (by clicking it), the image may be either cropped or too small for the screen.

Manual Sync The projector adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy or streaked, try turning Auto Image off then back on again. If the image still looks bad, try adjusting the signal synchronization manually as described below.

1 Click the Auto Image button to turn Auto Image off.

Image menu · Auto Image

Page 50 of the InFocus LP220 user manual — Image Menu Functions
Page 50 · click to enlarge
Page 50

U s i n g t h e P r o j e c t o r

2 Press the left or right mouse buttons repeatedly until the image is sharp and free of streaks.

Manual Tracking The tracking function adjusts the projector to match the video signal from your computer. The projector usually adjusts the tracking automatically when you connect your computer. How- ever, if the display shows evenly spaced, fuzzy, vertical lines or if the projected image is too wide or too narrow for the screen, try turning Auto Image off then back on again. If the image is still bad, try adjusting the tracking manually as described below.

Manual Tracking, Horiz.

Position and Vert. Position

buttons are available only for

computer sources. The projector

sets these options automatically

1 Click the Auto Image button to turn Auto Image off.

for a video source so they appear

gray.

2 Press the left or right mouse buttons repeatedly until the fuzzy vertical bars are gone.

Horiz. Position Follow these steps to manually adjust the horizontal position.

1 Click the Auto Image button to turn Auto Image off.

2 Press the left mouse button to move the image right; press the right mouse button to move the image left.

Positioning adjustments are saved when you power off the pro- jector.

Vert. Position Follow these steps to manually adjust the vertical position.

1 Click the Auto Image button to turn Auto Image off.

2 Press the left mouse button to move the image down; press the right mouse button to move the image up.

Positioning adjustments are saved when you power off the pro- jector.

Page 51 of the InFocus LP220 user manual — Controls Menu Functions
Page 51 · click to enlarge
Page 51

Controls Menu Functions

InFocus LP220 — Controls Menu Functions diagram (page 51)
Fig. 32 · Controls Menu Functions

When Auto is on, the projector attempts to pick the video stan- dard (NTSC, PAL or SECAM) automatically based on the input signal it receives. (The video standard options may vary depend- ing on your region of the world.) If the projector is unable to detect the standard, the colors might not look right or the image might appear “torn.” If this happens, manually select NTSC, PAL or SECAM.

standard used in your geographical

area, it’s often best to manually

select it.

Language You can display the on-screen menus in English, French, Ger- man, and Spanish. The default is English.

  • Click the button for the language you want. The menus redraw immediately.
  • Click either mouse button to turn the image upside down for ceiling-mounted projection.

mount kit, refer to “Accessories”

on page 57.

Controls menu · Video Standard · Ceiling

Page 52 of the InFocus LP220 user manual — Controls Menu Functions
Page 52 · click to enlarge
Page 52

U s i n g t h e P r o j e c t o r

Rear Projection When you select Rear Projection, the projector reverses the image so you can project from behind a translucent screen.

  • Click either mouse button to reverse the image.

When Auto is selected, the projector attempts to pick the correct monitor connection based on the input signal it receives. This set- ting produces the best results in most situations. Select “On” or “Off” only if the image is very dim or not projected.

  • Select “On” if your monitor is connected directly to the CableWizard and the images are excessively dim.

your monitor is connected directly

  • Select “Off” if your monitor is not connected directly to the CableWizard and the image is not projected. (Some IBM ThinkPad computers exhibit this problem, especially the ThinkPad 760.)

to the CableWizard.

Monitor Connect

Page 53 of the InFocus LP220 user manual — Maintenance
Page 53 · click to enlarge
Page 53

Maintenance

Page 54 of the InFocus LP220 user manual — Removing and Replacing a Lens
Page 54 · click to enlarge
Page 54

MAINTENANCE

This section describes how to:

  • clean and replace a lens
  • install and use the zoom lens
  • replace the projection lamp and reset the lamp monitor light
  • replace the batteries in the remote control
  • replace the fuse
  • use the Kensington lock feature

Cleaning the Lens

Follow these steps to clean the projection lens:

1 Apply a non-abrasive camera lens cleaner to a soft, dry clean- ing cloth.

  • Avoid using an excessive amount of cleaner.
  • Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

2 Lightly wipe the cleaning cloth over the lens.

3 If you don’t intend to use the projector immediately, replace the lens cap.

Removing and Replacing a Lens

1 Turn the focus ring counterclockwise until it reaches a stop.

2 While holding the lens, squeeze the latch below the lens (Figure 35) and turn the lens counterclockwise again.

3 Gently pull the lens out of the lens bracket.

Page 55 of the InFocus LP220 user manual — Using the Zoom Lens
Page 55 · click to enlarge
Page 55

M a i n t e n a n c e

InFocus LP220 — Using the Zoom Lens diagram (page 55)
Fig. 33 · Using the Zoom Lens

To replace a lens:

1 Make sure the latch is pointing down.

2 Squeeze the latch and gently push the lens in until it stops, then turn the lens clockwise until the catch is engaged.

Using the Zoom Lens

The zoom lens enlarges the projected image by 40% without moving the projector. (For more information about image size, see “Projected Image Size” on page 64.) Follow the previous instructions to install the zoom lens.

retract the zoom lens before you

put the lens cap on and pack the

Follow these steps when operating the zoom lens:

projector in its case.

1 Turn the zoom ring (Figure 36) until the projected image is the size you want, even if it is out of focus.

2 Turn the focus ring as needed to clear up the image.

InFocus LP220 — Using the Zoom Lens diagram (page 55)
Fig. 34 · Using the Zoom Lens

focus ring zoom ring

LitePro 200 Series zoom lens

Removing the lens

Page 56 of the InFocus LP220 user manual — Replacing the Projection Lamp
Page 56 · click to enlarge
Page 56

Replacing the Projection Lamp

The lamp monitor LED, marked on the connector panel, lights up when 150 hours of lamp life remains. At zero hours, the lamp switches off completely. You can order new lamp modules from your In Focus dealer. See “Accessories” on page 57 for informa- tion.

lamp explosion, allow the projector

to cool for at least 45 minutes

before you open the lamp module

Follow these steps to replace the projection lamp:

door. Never extract the lamp mod-

1 Turn off the projector and unplug the power cord.

ule while the lamp is operating.

2 Wait 45 minutes to allow it to cool thoroughly.

3 Using a small, flat-blade screwdriver, remove the screw on the outside of the lamp door (Figure 37).

4 Pull the lamp cover up and remove it.

tion lamp as soon as possible after

the lamp monitor light comes on. If

the lamp remains in use too long,

there is a danger of lamp explo-

sion. If this happens, your projector

will be severely damaged.

Removing the lamp module door

5 Loosen the non-removable screw on the outside of the mod- ule.

6 Remove the module (Figure 38).

projector with the lamp cover open

or removed. This disrupts the air

flow and causes the projector to

overheat.

Page 57 of the InFocus LP220 user manual — Replacing the Projection Lamp
Page 57 · click to enlarge
Page 57

M a i n t e n a n c e

InFocus LP220 — Replacing the Projection Lamp diagram (page 57)
Fig. 35 · Replacing the Projection Lamp

Removing the lamp module

7 Align the module in the correct direction.

8 Gently push the module in as far as it goes (Figure 39).

9 Tighten the screw on the outside of the module.

InFocus LP220 — Replacing the Projection Lamp diagram (page 57)
Fig. 36 · Replacing the Projection Lamp

lamp module or touch the glass

bulb! The glass may shatter and

cause injury.

Installing a new lamp module

10 Reposition the lamp cover.

11 Replace the screw and tighten it.

12 Turn the projector back on.

Page 58 of the InFocus LP220 user manual — Replacing the Fuse
Page 58 · click to enlarge
Page 58

Resetting the Lamp Monitor Light

After replacing the lamp, you must reset the lamp monitor light.

1 Press and hold the two brightness buttons on the keypad for at least 5 seconds.

2 Release the buttons. The lamp monitor light goes out after it is reset.

monitor light so the projector can

keep track of the usable life of the

Replacing the Batteries in the Remote Control

new lamp.

The life of the batteries depends on how often and how long you use the remote. Symptoms of low battery charge include erratic responses when using the remote and a reduced range of opera- tion.

Follow these steps to replace the batteries:

1 Turn the remote face down in your hand.

2 Slide the battery cover off the end of the remote by pressing on it with the heel of your hand.

3 Remove the old batteries.

4 Install two new AA alkaline batteries. Make sure you install each in the correct direction.

5 Slide the battery cover back on the remote.

Replacing the Fuse

A power line surge or spike can blow the power supply fuse, causing the projector to stop working. If this happens, you’ll need to replace the fuse.

The projector ships with a 6.3 amp fuse. The correct replacement fuse depends on the power line voltage in the country where you are operating the projector.

fied power supply fuse. Using a dif-

  • If your line voltage is 115V to 240V, use a T6.3AH, 250V, 5x20mm fuse.

ferent fuse may damage the

projector.

  • If your line voltage is 100V to 115V (as in Japan), use a T8AH, 250V, 5x20mm fuse. You can order the fuse from your In Focus dealer; the part number is listed on page 58.
Page 59 of the InFocus LP220 user manual — Resetting the Lamp Monitor Light
Page 59 · click to enlarge
Page 59

M a i n t e n a n c e

After you make sure that the condition that made the fuse blow no longer exists, follow these steps to replace the fuse:

1 Turn off the projector by pressing the “O” side of the power switch.

2 Unplug the power cord.

3 Remove the fuse holder, located just above the power cord connector. Pull out the fuse holder with a small, flat-blade screwdriver, key or coin (Figure 40).

InFocus LP220 — Resetting the Lamp Monitor Light diagram (page 59)
Fig. 37 · Resetting the Lamp Monitor Light

Removing the fuse holder

type fuse is required in Europe. In

4 Remove the blown fuse from the fuse holder (Figure 41).

countries with low main voltage,

you may need the 8.0A fuse to

avoid repeated (nuisance) blowing

of the 6.3A fuse. Both fuses

provide protection from risk of fire.

Do not use the projector if

repeated blowing still occurs after

switching to the 8.0A fuse. Call In

Removing the fuse from the fuse holder

Focus Technical Support for

5 Push the spare fuse into the holder until it is securely seated.

assistance.

6 Place the fuse holder back in position (Figure 42).

Page 60 of the InFocus LP220 user manual — Using the Kensington Lock
Page 60 · click to enlarge
Page 60

7 Plug the power cord back in.

8 Press the “|” side of the power switch to turn the projector back on.

power strip is recommended if

InFocus LP220 — Using the Kensington Lock diagram (page 60)
Fig. 38 · Using the Kensington Lock

power surges are common in your

area.

Replacing the fuse holder

Using the Kensington Lock

The projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System (Figure 43). Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector.

InFocus LP220 — Using the Kensington Lock diagram (page 60)
Fig. 39 · Using the Kensington Lock

Installing the Kensington lock

Page 61 of the InFocus LP220 user manual — Troubleshooting
Page 61 · click to enlarge
Page 61

Troubleshooting

Page 62 of the InFocus LP220 user manual — TROUBLESHOOTING
Page 62 · click to enlarge
Page 62

TROUBLESHOOTING

If you’re experiencing trouble with the projector, follow these steps to make sure everything is properly connected before you call Technical Support for assistance.

1 Check cable connections. Verify that all computer, CableWiz- ard and power cables are properly connected.

2 Verify that all power is switched on.

3 Verify that the projector has not been switched off with the standby button on the remote or keypad.

4 If the projector still doesn’t display an image, restart the com- puter.

5 If the problem still exists, unplug the projector from the com- puter and check the computer monitor’s display. The maxi- mum resolution that the 210 can display is 800x600 pixels, preferably 640x480; the maximum resolution that the 220 can display is 1024x768 pixels, preferably 800x600. The problem might be with the graphics controller in your computer rather than with the projector. When you reconnect the projector, remember to turn the computer and monitor off before you power up the projector. Power the equipment back up in this order: projector, monitor, computer.

require a specific power-up

sequencethe projector must be

turned on before you turn on the

computer.

6 If you’re using a laptop computer and its monitor is not dis- playing your presentation, make sure you have re-activated the computer’s monitor. Most laptop computers de-activate their own monitor when a second display device, such as the projector, is connected. Refer to page 59 for more information.

7 If the problem still exists, read through the problems and solutions in this chapter.

If you call Technical Support for assistance:

  • Find out what kind of graphics controller card is installed in your computer. This is the circuit board in the computer to which the projector is connected. Most PCs use a VGA graphics controller.
Page 63 of the InFocus LP220 user manual — Solutions to Common Problems
Page 63 · click to enlarge
Page 63

T r o u b l e s h o o t i n g

Solutions to Common Problems

Problem: Nothing on projection screen • Make sure that the power cord is properly connected to a func- tional AC electrical outlet. Make sure that the power cord is also properly connected to the projector.

  • If the projector is plugged into a power strip, make sure the power strip is turned on.
  • Make sure you have removed the lens cap on the projection lens at the front of the projector.
  • Make sure the projector is switched on.
  • Check the projector’s lamp to ensure that it is securely connected in the lamp module. See “Replacing the Projection Lamp” on page 43.
  • Check the fuse. If it has blown, replace it. See “Replacing the Fuse” on page 45.
  • Make sure that the CableWizard and the cables do not have any bent pins. Check the power cord for bent pins also.

Problem: Color or VGA text not being projected • You might need to adjust the brightness up or down until the text is visible. Refer to “Brightness” on page 29 for more infor- mation.

  • Verify that the appropriate input source is selected. See “Computer” on page 29 or “Video” on page 31.

Problem: The screen resolution is not right • Make sure the computer’s graphics card is set for a resolution of no greater than 800x600 for the 210, 1024x768 for the 220.

Problem: Image isn’t centered on the screen • Reposition the image. Refer to “Horiz. Position” on page 38 and “Vert. Position” on page 38.

  • If you’re using an extension cable between the CableWizard and the projector, make sure it’s In Focus-approved.
Page 64 of the InFocus LP220 user manual — Solutions to Common Problems
Page 64 · click to enlarge
Page 64

Problem: Only the start-up screen displays • Verify that the cables are connected correctly. Check to see that the CableWizard computer cable is correctly connected to the monitor connector on the computer (this is the connector where your monitor cable usually goes.) See page 6 through page 15 for connection procedures.

  • Verify that the proper input source is connected. See “Computer” on page 29 or “Video” on page 31.
  • You might need to turn everything off and power up the equipment again. Make sure you power up in this order: projector, computer monitor, computer. It is especially important that you follow this sequence for Macintosh computers.
  • Make sure your computer’s graphics board is installed and configured correctly.

If you’re using Windows 3.x:

1 In the Windows Program Manager, double-click the Win- dows Setup icon in the Main program group.

2 Verify that the Display setting is 800x600 or less for the 210, 1024x768 or less for the 220.

If you’re using Windows 95:

1 Open “My Computer” icon, the Control Panel folder and then the Display icon.

2 Click the Settings tab.

3 Verify that the Desktop area is set to 800x600 or less for the 210, 1024x768 or less for the 220.

Also check the following:

  • Does your computer have a compatible graphics board? The projector isn’t CGA or EGA compatible.
  • Is your computer’s graphics board turned on? This is especially true for laptop computers. See “Portable and Laptop Activation Chart” on page 59.
Page 65 of the InFocus LP220 user manual — Solutions to Common Problems
Page 65 · click to enlarge
Page 65

T r o u b l e s h o o t i n g

Problem: Image is too wide or narrow for screen • You might need to manually adjust the tracking to reduce or enlarge the projected image. Refer to “Manual Tracking” on page 38.

  • Adjust the resolution of your monitor if it’s greater than 800x600 pixels for the 210 or 1024x768 for the 220. Only these resolutions at 75 Hz or less will display on the projector.
  • Make sure that your computer has a compatible graphics board. The projector is not compatible with CGA, EGA, or 1280x1024 graphics modes.

Problem: Image is out of focus • Make sure the lens is locked in place.

  • Turn the projection lens to focus the image.
  • Make sure the projection screen is at least 4 feet (1.2m) from the projector.
  • Check the projection lens to see if it needs cleaning.

Problem: Image and menus are reversed left to right • Rear projection mode is probably turned on. Switch back to forward projection from the Controls menu. The image should immediately return to forward projection. See “Rear Projec- tion” on page 40.

Problem: Image and menus are upside down • Ceiling mode is probably turned on. Turn off the mode from the Controls menu. The image should immediately return to forward projection. See “Ceiling” on page 39.

Problem: the projector displays vertical lines, “bleeding” or spots • Adjust the brightness. See “Brightness” on page 29.

  • Check the projection lens to see if it needs cleaning.
Page 66 of the InFocus LP220 user manual — Solutions to Common Problems
Page 66 · click to enlarge
Page 66

Problem: Image is “noisy” or streaked Try these steps in this order.

1 Deactivate the screen saver on your computer.

2 Turn Auto Image off and then back on again. See “Auto Image” on page 37.

3 Adjust the synchronization and tracking manually to find an optimal setting. See “Manual Sync” on page 37 and “Manual Tracking” on page 38.

  • If you’re using an extension cable between the CableWizard and the projector, make sure it’s In Focus-approved.
  • The problem could be with your computer’s graphics board. If possible, connect another computer with a different graphics board.

Problem: Projected colors don’t match the computer or video player’s colors • Adjust the brightness, tint and/or contrast from the Display menu. Just as there are differences in the displays of different monitors, there are often differences between the computer image and the projected image. See “Brightness” on page 29, “Tint” on page 34 and “Contrast” on page 34.

Problem: Lamp seems to be getting dimmer • The lamp begins to lose brightness when it has been in use for a long time. Replace the lamp as described in “Replacing the Pro- jection Lamp” on page 43.

Problem: Lamp shuts off • A minor power surge may cause the lamp to shut off. Turn the projector off, wait at least 45 seconds, then turn it back on.

Problem: Remote not operating correctly • You might need to replace the batteries. See “Replacing the Batteries in the Remote Control” on page 45.

  • Make sure you’re pointing the remote either at the back or front of the projector, or at the projection screen.
  • Make sure the remote is within its operating range of 40 feet.
Page 67 of the InFocus LP220 user manual — Appendix
Page 67 · click to enlarge
Page 67

Appendix

Page 68 of the InFocus LP220 user manual — APPENDIX
Page 68 · click to enlarge
Page 68

APPENDIX

Specifications

The LitePro 210 and 220 must be operated and stored within the temperature and humidity ranges specified.

Temperature Operating 10 C to 40° C Non-operating -20 to 60° C

Humidity Operating and non-oper. 10% to 95% relative humidity, non-condensing

Dimensions 6.6 x 16.25 x 13.25 inches (16.8 x 41.3 x 33.7 cm)

Weight 16 lbs. (7.3 kg) unpacked

Altitude Operating 0 to 10,000 feet (3048 meters) Non-operating 20,000 feet (6096 meters)

Left and Right Audio Outputs Frequency Response 10 Hz - 20 KHz Output Impedance 1.2 K ohm nominal Output Voltage 2 Vrms maximum (open circuit) Connector Type red and white RCA jacks

Subwoofer Outputs Frequency Response 10 Hz - 10 KHz Output Impedance 200 ohms nominal Output Voltage 2 Vrms maximum (open circuit) Connector Type black RCA jack

Optics Focus Range 4 to 25 feet

Page 69 of the InFocus LP220 user manual — Appendix
Page 69 · click to enlarge
Page 69

A p p e n d i x

Microphone Input Input Impedance 3.5 K ohm nominal Maximum Input Voltage 60 mVrms for THD ≤0.3%, main inputs off Sensitivity 800 Vrms at 1 KHz for 88 dB SPL at 1 meter Microphone Impedance < 8K ohms Connector Type 6.3 mm (1/4 inch) monaural phone jack (unbalanced)

Lamp Type 270-watt metal halide

Remote Control Battery Two (2) AA alkaline cells

Input Power Requirements 100-240VAC, 7.0A-3.6A, 50 to 60 Hz.

Video Module Input Input Impedance 5K ohm DC coupled Maximum Input Voltage (LIN + RIN)PEAK < 4.5 V for THD ≤ 0.3%, micro- phone off LIN or RIN < 2.0 Vrms for THD ≤ 0.3%, micro- phone off Sensitivity 100 mV at 1 KHz for 88 dB SPL at 1 meter Connector Type RCA jack

CableWizard Audio Input Input Impedance 10K ohm nominal, AC coupled Maximum Input Voltage (LIN + RIN)PEAK < 4.5 V for THD ≤ 0.3%, micro- phone off LIN or RIN < 2.0 Vrms for THD ≤ 0.3%, micro- phone off Sensitivity 100 mV at 1 KHz for 88 dB SPL at 1 meter Connector Type 3.5 mm (1/8 inch) stereo phone jack

Fuse 115 to 240V nominal line T6.3AH, 250V, 5x20mm 100 to 115V nominal line T8AH, 250V, 5x20mm

Page 70 of the InFocus LP220 user manual — Accessories
Page 70 · click to enlarge
Page 70

Accessories

Standard Accessories (ship with the projector) Part Number

LitePro 210/220 Quick Start card 009-0214-xx

LitePro 210/220 User’s Guide 010-0102-xx

CableWizard and Cables 591-0182-xx

CableWizard Audio Cable 210-0079-xx

CableWizard Computer Cable 210-0076-xx

CableWizard Mouse Cable 210-0078-xx

Projection Lamp Module 505-0144-xx

Fuse — 6.3 amp 749-0010-xx

Remote Control with Cable and 2 Batteries 590-0198-xx

Remote Cable (50 ft) 210-0088-xx

Power Cords (one ships with projector, type depends on country)

North American Power Cord 210-0023-xx

Australian Power Cord 210-0027-xx

UK Power Cord 210-0028-xx

European Power Cord 210-0029-xx

Danish Power Cord 210-0030-xx

Swiss Power Cord 210-0031-xx

Show 4 more labels / short text on this page
Shipping Box 110-0098-xx · Varifocal Lens 505-0148-00 · Lens Cap 340-0220-xx · Audio/Video Cable 210-0062-xx
Page 71 of the InFocus LP220 user manual — Accessories
Page 71 · click to enlarge
Page 71

A p p e n d i x

Soft Carry Case CA-C077

ATA Shipping Case CA-C119

Mac Adapter for CableWizard Lite 516-0003-xx

CableWizard Extension Cable, 50 ft* 210-0077-xx

Kensington MicroSaver Security System SP-KENLOC

JBL Satellite Speakers 591-0203-xx

Fuse — 8.0 amp call for part no.

LitePro 200 Series Ceiling Mount Kit* 591-0208-xx

1 Year Extended Warranty 592-0320-xx

2 Year Extended Warranty 592-0319-xx

*Using the extension cable or ceiling mount reduces FCC and EMC compliance to Class A.

Show 6 more labels / short text on this page
Optional Accessories · CableWizard Lite SP-CWLITE · Zoom Lens HW-LP210-ZM · JBL Subwoofer 591-0204-xx · S-Video Cable 515-0027-xx · Microphone 591-0201-xx
Page 72 of the InFocus LP220 user manual — FN-F6 FN-F6
Page 72 · click to enlarge
Page 72

Portable and Laptop Activation Chart

Key command to activate port

Key command to de-activate port

de-activate their built-in monitors

Acer Ctrl-Alt-Esc (for setup) Ctrl-Alt-Esc (for setup)

when a second display device is

AST* ** FN-D or Ctrl-D FN-D or Ctrl-D

connected. The following chart lists

the commands that re-activate the

FN-F5 FN-F5

laptop’s monitor. If your computer

type from A:/IVGA/CRT type from A:/IVGA/CRT

is not listed, refer to the com-

FN-F12 FN-F12

puter’s documentation.

setup VGA/ Conf.Simulscan

setup VGA/ Conf.Simulscan

FN-F5 FN-F5

F2/Choose Option/F5 F2/Choose Option/F5

Amrel* ** setup menu setup menu

Apple see Mac Portable and Mac PowerBook

BCC* automatic reboot computer

Bondwell LCD or CRT options after bootup

reboot for LCD or CRT options to appear

Chaplet** setup screen setup screen

FN-F6 FN-F6

FN-F4 FN-F4

Show 9 more labels / short text on this page
Computer · Ctrl-FN-D Ctrl-FN-D · Advanced Logic Research · Ctrl-Alt-V Ctrl-Alt-V · Altima Shift-Ctrl-Alt-C Shift-Ctrl-Alt-L · Ambra** FN-F12 FN-F12 · Shift-Ctrl-D Shift-Ctrl-D · Aspen automatic automatic · Commax Ctrl-Alt-#6 Ctrl-Alt-#5
Page 73 of the InFocus LP220 user manual — FN-F2
Page 73 · click to enlarge
Page 73

A p p e n d i x

Key command to activate port

Key command to de-activate port

Compaq* ** Ctrl-Alt-< Ctrl-Alt->

FN-F4 FN-F4

mode/? (for setup option) mode/? (for setup option)

Compuadd* ** automatic automatic

Alt-F for screen setup option

Alt-F for screen setup option

Data General Ctrl-Alt-Command Ctrl-Alt-Command

2 CRT/X at DOS prompt reboot

FN-F8 (CRT/LCD) FN-F8

FN-D FN-D

FN-F12 FN-F12

FN-F2 FN-F2

Dolch dip switch to CRT dip switch to LCD

Epson dip switch to CRT dip switch to LCD

Everex* setup screen option setup screen option

Gateway FN-F1/FN-F1 again simul- taneous

FN-F1

Grid* ** FN-F2, choose auto or simultaneous

FN-F2

Hyundai setup screen option setup screen option

IBM 970* automatic warm reboot

Show 9 more labels / short text on this page
Computer · automatic automatic · Data General Walkabout · Datavue Ctrl-Shift-M Ctrl-Shift-M · Dell** Ctrl-Alt-< Ctrl-Alt-> · Ctrl-Alt-F10 Ctrl-Alt-F10 · Digital* automatic reboot · For-A Ctrl-Alt-Shift-C Ctrl-Shift-Alt-L · Ctrl-Alt-Tab Ctrl-Alt-Tab
Page 74 of the InFocus LP220 user manual — FN-F31 FN-F3
Page 74 · click to enlarge
Page 74

Key command to activate port

Key command to de-activate port

IBM ThinkPad** reboot, enter setup menu FN-F2

FN-F7, select choice from setup menu

PS/2 SC select choice (CRT, LCD, etc.)

Kaypro boot up, monitor plugged in

Kris Tech FN-F8 FN-F8

Mac Portable 100 no video port: not compatible

140, 145, 150, 170 no video port: requires a 3rd-party interface

160, 165, 180, 520, 540, 5300 Control Panel folder, PowerBook Display folder; Activate Video Mirroring

210, 230, 250, 270, 280, 2300 requires Apple Docking Station or Mini Dock

Micro Express* automatic warm reboot

Microslate* automatic warm reboot

Mitsubishi SW2 On-Off-Off-Off SW2 Off-On-On-On

NCR setup screen option setup screen option

NEC* ** setup screen option setup screen option

CRT at the DOS prompt LCD at the DOS prompt

FN-F31 FN-F3

FN-O/* FN-O/*

FN- | | FN- | |

Show 9 more labels / short text on this page
Computer · FN-F1, select choice · FN-F5, select choice · unplug monitor · Mac PowerBook · warm reboot · Magitronic FN-F4 FN-F4 · Mastersport FN-F2 FN-F1 · Olivetti* automatic automatic
Page 75 of the InFocus LP220 user manual — FN-F2 FN-F2
Page 75 · click to enlarge
Page 75

A p p e n d i x

Key command to activate port

Key command to de-activate port

Packard Bell** FN-F2 FN-F2

Samsung* setup screen option setup screen option

Sanyo setup screen option setup screen option

Sharp dip switch to CRT dip switch to LCD

setup screen option setup screen option

setup screen option setup screen option

Top-Link* ** setup screen option setup screen option

FN-F6 FN-F6

Toshiba* ** Ctrl-Alt-End Ctrl-Alt-Home

FN-F5 FN-F5

setup screen option setup screen option

FN-F5 FN-F5

Wyse software driven software driven

FN-F2 FN-F2

FN-F1 FN-F1

* These manufacturers have models that automatically send video to the external CRT port when some type of display device is attached.

** These manufacturers offer more than one key command depend- ing on the computer model.

Show 12 more labels / short text on this page
Computer · Ctrl-Alt-< Ctrl-Alt-> · Panasonic FN-F2 FN-F2 · Sun SPARC- Dataview · Ctrl-Shift-M Ctrl-Shift-M · Tandy** Ctrl-Alt-Insert Ctrl-Alt-Insert · Texas Instru- ments* · FN-End FN-Home · Twinhead* FN-F7 FN-F7 · Automatic Automatic · WinBook Ctrl-Alt-F10 Ctrl-Alt-F10 · Zenith** FN-F10 FN-F10
Page 76 of the InFocus LP220 user manual — Using Video Mirroring with a PowerBook Computer
Page 76 · click to enlarge
Page 76

Using Video Mirroring with a PowerBook Computer

When you turn video mirroring on, the projector displays the same information that appears on your PowerBook’s built-in screen. When video mirroring is off, the projector acts like a sepa- rate display.

To turn on video mirroring for the first time:

1 Open the Monitors control panel; click on Monitor 2.

2 Set the number of colors you want.

3 Open the Control Strip; click on the monitor icon.

4 Select “Turn Video Mirroring On.”

Now you can turn video mirroring on and off from the Control Strip without having to open the Monitors control panel again.

When using video mirroring and high color graphics such as slide shows, the projected image occasionally might turn black and white. If this happens, perform the following steps:

1 Turn off video mirroring.

2 Open the Monitors control panel.

3 Move the white menu bar to Monitor 2 to set the projector as the primary monitor.

4 Restart the PowerBook.

Page 77 of the InFocus LP220 user manual — Projected Image Size
Page 77 · click to enlarge
Page 77

A p p e n d i x

Projected Image Size

Use the chart below and the tables on the next page to help you determine projected image sizes for the varifocal and zoom lenses.

InFocus LP220 — Projected Image Size diagram (page 77)
Fig. 40 · Projected Image Size

Projected image size for LitePro 200 series zoom and varifocal lenses

Page 78 of the InFocus LP220 user manual — Projected Image Size
Page 78 · click to enlarge
Page 78
Table 1Image Size, Width and Height for Varifocal Lens

and Zoom Lens at Minimum Focusing Distance

Distance to Screen (feet)

Height (inches) 4 34 27 20.4 10 84 67 50.4 15 126 101 75.6 20 168 134 100.8 25 210 168 126. 30 252 202 151.2 35 294 235 176.4 40 336 269 201.6

Table 2Image Size, Width and Height for Zoom Lens at

Distance to Screen (feet)

Height (inches) 4 48 38 28.8 10 120 96 72 15 180 144 108 20 240 192 144 25 300 240 180 30 360 288 216 35 420 336 252 40 480 384 288

* The focusing distance of the zoom lens is from 4 feet to infinity.

Show 10 more labels / short text on this page
Diagonal · Width (inches) · (inches) · Maximum Focusing* Distance · Maximum · Maximum · Maximum · Diagonal · Width (inches) · (inches)
Page 79 of the InFocus LP220 user manual — Index
Page 79 · click to enlarge
Page 79

Index

Page 81 of the InFocus LP220 user manual — Table of contents
Page 81 · click to enlarge
Page 81

Table of contents

Table of Contentsp.6Safety Summaryp.8Introductionp.12Image Resolutionp.12Compatibilityp.13Unpacking the Projectorp.13Usage Guidelinesp.15If You Need Assistancep.15Warrantyp.15Setting up the Projectorp.17Connecting the CableWizard to the Projectorp.18Selecting Connectors on the CableWizardp.18Preparing to Connect Your Equipment to the Project...p.20Connecting an IBM-Compatible Desktop Computerp.21Connecting an IBM-Compatible Laptop Computerp.23Connecting a Macintosh Desktop Computerp.25Connecting an Apple PowerBook Computerp.27Connecting a Video Playerp.29Connecting an External Speaker and a Subwooferp.31Connecting a Microphonep.32Connecting a PS/2-Compatible Mousep.32Connecting the Remote Control Cablep.33Powering up the Projector and Adjusting the Imagep.33Turning Off the Projectorp.35Using the Projectorp.37Basic Image Adjustmentp.37Using the Remote Controlp.37Adjusting the Projectorp.38Using the Remote and Keypad Buttonsp.40Using the Disk Mousep.44Using the On-Screen Menusp.44Display Menu Functionsp.45Audio Menu Functionsp.47Image Menu Functionsp.49Controls Menu Functionsp.51Maintenancep.54Cleaning the Lensp.54Removing and Replacing a Lensp.54Using the Zoom Lensp.55Replacing the Projection Lampp.56Resetting the Lamp Monitor Lightp.58Replacing the Batteries in the Remote Controlp.58Replacing the Fusep.58Using the Kensington Lockp.60Troubleshootingp.62Solutions to Common Problemsp.63Appendixp.68Specificationsp.68Accessoriesp.70Portable and Laptop Activation Chartp.72Using Video Mirroring with a PowerBook Computerp.76Projected Image Sizep.77Indexp.80
Page 82 of the InFocus LP220 user manual — Table of contents
Page 82 · click to enlarge
Page 82

Table of contents

Table of Contentsp.6Safety Summaryp.8Introductionp.12Image Resolutionp.12Compatibilityp.13Unpacking the Projectorp.13Usage Guidelinesp.15If You Need Assistancep.15Warrantyp.15Setting up the Projectorp.17Connecting the CableWizard to the Projectorp.18Selecting Connectors on the CableWizardp.18Preparing to Connect Your Equipment to the Project...p.20Connecting an IBM-Compatible Desktop Computerp.21Connecting an IBM-Compatible Laptop Computerp.23Connecting a Macintosh Desktop Computerp.25Connecting an Apple PowerBook Computerp.27Connecting a Video Playerp.29Connecting an External Speaker and a Subwooferp.31Connecting a Microphonep.32Connecting a PS/2-Compatible Mousep.32Connecting the Remote Control Cablep.33Powering up the Projector and Adjusting the Imagep.33Turning Off the Projectorp.35Using the Projectorp.37Basic Image Adjustmentp.37Using the Remote Controlp.37Adjusting the Projectorp.38Using the Remote and Keypad Buttonsp.40Using the Disk Mousep.44Using the On-Screen Menusp.44Display Menu Functionsp.45Audio Menu Functionsp.47Image Menu Functionsp.49Controls Menu Functionsp.51Maintenancep.54Cleaning the Lensp.54Removing and Replacing a Lensp.54Using the Zoom Lensp.55Replacing the Projection Lampp.56Resetting the Lamp Monitor Lightp.58Replacing the Batteries in the Remote Controlp.58Replacing the Fusep.58Using the Kensington Lockp.60Troubleshootingp.62Solutions to Common Problemsp.63Appendixp.68Specificationsp.68Accessoriesp.70Portable and Laptop Activation Chartp.72Using Video Mirroring with a PowerBook Computerp.76Projected Image Sizep.77Indexp.80
Page 83 of the InFocus LP220 user manual — Table of contents
Page 83 · click to enlarge
Page 83

Table of contents

Table of Contentsp.6Safety Summaryp.8Introductionp.12Image Resolutionp.12Compatibilityp.13Unpacking the Projectorp.13Usage Guidelinesp.15If You Need Assistancep.15Warrantyp.15Setting up the Projectorp.17Connecting the CableWizard to the Projectorp.18Selecting Connectors on the CableWizardp.18Preparing to Connect Your Equipment to the Project...p.20Connecting an IBM-Compatible Desktop Computerp.21Connecting an IBM-Compatible Laptop Computerp.23Connecting a Macintosh Desktop Computerp.25Connecting an Apple PowerBook Computerp.27Connecting a Video Playerp.29Connecting an External Speaker and a Subwooferp.31Connecting a Microphonep.32Connecting a PS/2-Compatible Mousep.32Connecting the Remote Control Cablep.33Powering up the Projector and Adjusting the Imagep.33Turning Off the Projectorp.35Using the Projectorp.37Basic Image Adjustmentp.37Using the Remote Controlp.37Adjusting the Projectorp.38Using the Remote and Keypad Buttonsp.40Using the Disk Mousep.44Using the On-Screen Menusp.44Display Menu Functionsp.45Audio Menu Functionsp.47Image Menu Functionsp.49Controls Menu Functionsp.51Maintenancep.54Cleaning the Lensp.54Removing and Replacing a Lensp.54Using the Zoom Lensp.55Replacing the Projection Lampp.56Resetting the Lamp Monitor Lightp.58Replacing the Batteries in the Remote Controlp.58Replacing the Fusep.58Using the Kensington Lockp.60Troubleshootingp.62Solutions to Common Problemsp.63Appendixp.68Specificationsp.68Accessoriesp.70Portable and Laptop Activation Chartp.72Using Video Mirroring with a PowerBook Computerp.76Projected Image Sizep.77Indexp.80
Page 84 of the InFocus LP220 user manual — Table of contents
Page 84 · click to enlarge
Page 84

Table of contents

Table of Contentsp.6Safety Summaryp.8Introductionp.12Image Resolutionp.12Compatibilityp.13Unpacking the Projectorp.13Usage Guidelinesp.15If You Need Assistancep.15Warrantyp.15Setting up the Projectorp.17Connecting the CableWizard to the Projectorp.18Selecting Connectors on the CableWizardp.18Preparing to Connect Your Equipment to the Project...p.20Connecting an IBM-Compatible Desktop Computerp.21Connecting an IBM-Compatible Laptop Computerp.23Connecting a Macintosh Desktop Computerp.25Connecting an Apple PowerBook Computerp.27Connecting a Video Playerp.29Connecting an External Speaker and a Subwooferp.31Connecting a Microphonep.32Connecting a PS/2-Compatible Mousep.32Connecting the Remote Control Cablep.33Powering up the Projector and Adjusting the Imagep.33Turning Off the Projectorp.35Using the Projectorp.37Basic Image Adjustmentp.37Using the Remote Controlp.37Adjusting the Projectorp.38Using the Remote and Keypad Buttonsp.40Using the Disk Mousep.44Using the On-Screen Menusp.44Display Menu Functionsp.45Audio Menu Functionsp.47Image Menu Functionsp.49Controls Menu Functionsp.51Maintenancep.54Cleaning the Lensp.54Removing and Replacing a Lensp.54Using the Zoom Lensp.55Replacing the Projection Lampp.56Resetting the Lamp Monitor Lightp.58Replacing the Batteries in the Remote Controlp.58Replacing the Fusep.58Using the Kensington Lockp.60Troubleshootingp.62Solutions to Common Problemsp.63Appendixp.68Specificationsp.68Accessoriesp.70Portable and Laptop Activation Chartp.72Using Video Mirroring with a PowerBook Computerp.76Projected Image Sizep.77Indexp.80
Page 85 of the InFocus LP220 user manual — Index
Page 85 · click to enlarge
Page 85

LIMITED WARRANTY In Focus Systems Inc. (“In Focus”) warrants that each LitePro 210 and 220 (“the Product”) sold hereunder will conform to and function in accordance with the written specifications of In Focus. Said limited warranty shall apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale. Said warranty shall continue for a period of one (1) year from the date of such purchase. In Focus does not warrant that the Product will meet the specific requirements of the first person or entity that purchases the Product for personal or business use. In Focus’ liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the Prod- uct or refund of the purchase price of the Product, at In Focus’ sole option. To exercise the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and expense, to In Focus or to any autho- rized In Focus service center provided, however, that the Product must be accompanied by a written letter explaining the problem and which includes (i) proof of date of purchase; (ii) the dealer’s name; and (iii) the model and serial number of the Product. A return authorization number, issued by the In Focus customer service department, must also be clearly dis- played on the outside of the shipping carton containing the Product.

WARRANTY LIMITATION AND EXCLUSION In Focus shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations, or service other than by In Focus or its authorized agents, causes other than from ordinary use or failure to properly use the Product in the application for which said Product is intended.

DISCLAIMER OR UNSTATED WARRANTIES THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MER- CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY IN FOCUS.

LIMITATION OF LIABILITY IT IS UNDERSTOOD AND AGREED THAT IN FOCUS’ LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL IN FOCUS BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. THE PRICE STATED FOR THE PRODUCT IS A CONSIDER- ATION IN LIMITING IN FOCUS’ LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREE- MENT TO PURCHASE THE PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED.

Page 86 of the InFocus LP220 user manual — Index
Page 86 · click to enlarge
Page 86

Part Number 010-0102-02

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the InFocus LP220

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus LP220

Be the first to ask — other owners or our team will answer.

Original document

InFocus LP220 manual PDF

86 pages·1.6 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…