Instruction/ maintenance manual of the product LCD/LVDS/LAN IBM
Go to page of 154
PCI-6871 PCI Eden400 Half-sized SBC with SODIMM/VGA LCD/L VDS/LAN and CFC2 Users’ Manual.
PCI-6871 User’s Manual ii Copyright This document is copyrighted, © 2002. Al l rights are reserved. The orig- inal manufacturer reserves the right to make improvements to the prod- ucts described in this manual at any time wi thout notice.
iii Packing List Before you begin installing your card, please make su re that the following materials have been shipped: • 1 ea. PCI-6871 all-in-one single board computer • 1 ea. startup manual • CD-ROM or disks for utility , driv ers, and manual (in PDF format) • 1 ea.
PCI-6871 User’s Manual iv.
Table of Contents v Contents Chapter 1 General Information ........................................ 1 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Features .......... ................. ............
vi 2.19.2 Flat panel display connector (CN18) ...... ......... ............. 21 2.19.3 Extension flat pa nel connector (CN17) .. ......... ............. 21 2.19.4 LVDS LCD panel connector (C N21) ............ ......... ...... 21 2.19.5 Panel type selec tion (S1).
Table of Contents vii 5.2.1 Inst allation for Windows 95 ................. ........... ........... .. 48 5.2.2 Inst allation for Windows 98/Me .. ........... ........... ........... 52 5.2.3 Inst allation for Windows NT ... ........... ........... ...
viii C.14 CRT Display Connector (CN12) ............................ ....... 131 C.15 Flat Panel Connector (CN18) ........................... ............. 132 C.16 Extended Flat Panel Disp lay Connector (CN17) .......... 133 C.17 LCD Signal Mapping ..
1 Chapter 1 General Information 1 General Information This chapter gives background information on the PCI-6871. Sections include: • Introduction • Features • Specifications • Board layout and.
PCI-6871 User’s Manual 2 Chapter 1 Introduction 1.1 Introduction The new PCI- 6 87 1 is a half-sized CPU card w i th on b oar d V I A Eden400 C3 EB GA fanless CPU. The VI A Eden processor uses advanced 0.13µ CMOS technology with 128KB L1 cache memory and 64KB L2 cache memory on die.
3 Chapter 1 General Information 1.2 Features • Embedded low power VIA Ed en C3 EGBA 400MHz processor • Half-sized CPU card with PCI golden finger • Fanless operation at 60° C.
PCI-6871 User’s Manual 4 • Keyboard/mouse connector: Su pports standard PC/A T keyboard and a PS/2 mouse • Power management: Supports power saving modes including Nor- mal/Standby/Suspend modes.
5 Chapter 1 General Information 1.4 Board layout: dimensions Figure 1.1: Board layout: dimensions (comp onent side) I + PCI-6871 REV. A1.
PCI-6871 User’s Manual 6 Figure 1.2: Board layout: di mensions (solder side) + PCI-6871 REV.A1.
7 Chapter 2 Installation 2 Installation This chapter explains the setup procedures of PCI-6871 hardware, including instruc- tions on setting jumpers and con necting peripherals, switches and indicators. Be sure to read all safe ty precautions before you begin the i nstallation procedure.
PCI-6871 User’s Manual 8 Chapter 2 Installation 2.1 Jumpers The PCI-6871 has a number of jumper s that allow you to confi gure your system to suit your application.
9 Chapter 2 Installation CN9 IR CON CN10 Audio I/F CN1 1 MAIN PWR CON CN12 D-SUB VGA CN13 HDD, PWR LED CON & WDT Output CN14 DIO CON CN15 LAN RJ45 CON CN16 PC104 CN17 LCD CON2 (10*2) CN18 LCD CON1.
PCI-6871 User’s Manual 10 2.3 Locating jumpers Figure 2.1: Jumper locations + PCI-6871 REV.A1 I.
11 Chapter 2 Installation 2.4 Locating Connectors Figure 2.2: Connectors (component side) PCI-6871 REV.A1 + I.
PCI-6871 User’s Manual 12 2.5 Setting Jumpers Y ou may configu re your card to match the needs of your appl ication by setting jumper s. A jumper is a metal br idge used to close an electric cir- cuit. It consists of two metal pi ns and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
13 Chapter 2 Installation 2.6 Clear CMOS (JP1) This jumper is used to erase CMOS data and reset system BIOS informa- tion. The procedure for clearing CMOS is: 1. T urn off the system. 2. Short pi n 2 and pin 3. 3. Return jump er to pins 1 an d 2. 4. T urn on the system.
PCI-6871 User’s Manual 14 2.7 Installing system memory (SODIMMs) You can install anywhere from 32 to 512 MB of SDRAM in to your PCI-6871 Se- ries card. The card pro vides two 144-p in SODIMM sockets. Each socket ac- cepts 32/64/128/256/512 MB 3.3 V power level SODIMMs.
15 Chapter 2 Installation Important: Only use standard form SODIMM memory modules (as shown in the diagram below) . Standardized dimensions ensure a proper fit.
PCI-6871 User’s Manual 16 2.8.1 Connecting the hard drive Connecting drives is done in a daisy-ch ain fashion. It requires one of two cables (not included in this package) , dependin g on the drive size. 1.8" and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flat-cable connector .
17 Chapter 2 Installation 2.10.1 Connecting the floppy drive 1. Plug the 34-pin flat-cable connect or into CN6. Make sure that the red wire corresponds to pin one on the connector . 2. Attach the appropriat e connector on the other end of the cable to the floppy drive(s).
PCI-6871 User’s Manual 18 standard PC/A T BIOS will report an error or fail during power-on self- test (POST) after a reset. The PC I-6871’ s BIOS standard setup menu allows you to select “All, But Key board” under the “Halt On” selection.
19 Chapter 2 Installation 2.15 A TX power contro l connector (CN3, CN5) 2.15.1 A TX feature connector (CN3) and soft power switch connector (CN5) The PCI-6871 can support an advanced soft po wer switch function, if an A TX power supply is used. T o enable the soft power switch function: 1.
PCI-6871 User’s Manual 20 2.16 IR connector (CN9) This connector suppo rts the optio nal wireless infrared transmitt ing and receiving module. This mo dule mounts on the syst em case.
21 Chapter 2 Installation 2.19.1 CRT display connector (CN12) CN12 is a stan dard 15-pin D-SUB connect or commonly used for VGA. The pin assignments for CR T displa y connect or CN12 are detailed in Appendix C. 2.19.2 Flat panel display connector (CN18) CN18 consists of a 40-pin connector which can supp ort a 24-bit LCD panel.
PCI-6871 User’s Manual 22 2.19.5 Panel type selection (S1) S1 is an 8 segment DIP switch for DSTN/TFT panel type and resolution functions. 2.20 Ethernet configuration The PCI-6871 is equipped wi th a high performance 32-b it PCI-bus Ether- net interface which is fully compli ant with IEEE 802.
23 Chapter 2 Installation 2.20.1 100Base-T connector (CN15) CN15 is an RJ-45 connector with LED.. 2.20.2 Network boot The Network Boot feature can be utilized by incorporati ng the Boot ROM image files for the appropriate net work operating system. The Boot ROM BIOS files are included in the system BIOS, which is on the utility CD disc.
PCI-6871 User’s Manual 24 2.22 USB connectors (CN4, CN23) The PCI-6871 board provides up to four USB (Universal Serial Bus) ports, with USB3 and USB4 optional. This gives complete Plu g and Play , and hot attach/detach fo r up to 127 external devices.
25 Chapter 3 Software Configuration 3 Software Configuration This chapter details the software configura- tion information. It shows you how to config- ure the card to match your application requirements. The A W ARD System BIOS is covered in Chapter 4.
PCI-6871 User’s Manual 26 Chapter 3 Software Configuration 3.1 Introduction The PCI-6871 system BIOS and custom drivers are located in a 256 Kbyte, Flash ROM de vice, designated U18. A single Flash chip holds the system BIOS, VGA BIOS and network Boot ROM image.
27 Chapter 3 Software Configuration 3.2 Connections to Three Standard LCDs The following tables illustrate typical LC D connection pinouts for the PCI-6871.
PCI-6871 User’s Manual 28 3.2.2 Connecti ons to T oshiba L TM15C151A (1024 x 768 TFT color LCD) 28 B5 16 P7 29 GND 3 GND 30 VDD 1 +5 V 31 VDD 2 +5 V T able 3.
29 Chapter 3 Software Configuration 3.2.3 Connecti ons to T oshiba L TM12C275A (800 x 600 TFT co lor LCD) CN1-25 OB5 CN 10-13 PD34 CN1-26 ENAB CN 1 1-37 M/DE CN1-27 G ND CN 1 1-34 GND CN1-28 V DD CN 1 1-1 +5V CN1-29 V DD CN 1 1-2 +5V CN1-30 G ND CN 1 1-8 GND T able 3.
PCI-6871 User’s Manual 30 3.3 Ethernet software configuration The PCI-6871’ s on-board Ethernet inte rface supports all major network operating systems. T o co nfigure th e medium type , to view the current configuration, or to run diagnostics, do the fo llowing: 1.
31 Chapter 3 Software Configuration Note For Ethernet installation, plea se see Chapter 7.
PCI-6871 User’s Manual 32.
33 Chapter 4 Award BIOS Setup Chapter 4 Ducks that N eed Love! 4 A ward BIOS Setup This chapter describes how to set BIOS configuration data. CHAPTER.
PCI-6871 User’s Manual 34 Chapter 4 A ward BIOS Setup 4.1 System test and initialization These routines test and initialize bo ard hardware. If the routines encoun- ter an error during the tests, you wil l either hear a few short beeps or see an error message on the sc reen.
35 Chapter 4 Award BIOS Setup 4.2 Award BIOS setup A w ard’ s BIOS ROM has a built-in Set up program that allows users to modify the basic system configu ration. This type of inform ation is stored in battery-backed CMOS RAM so that it reta ins the Setup in formation when the power is turned off.
PCI-6871 User’s Manual 36 4.2.2 Standard CMOS Features setup When you choose the Standard CMOS Features option from the Initial Setup Screen menu, the screen shown belo w is displayed. This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display .
37 Chapter 4 Award BIOS Setup 4.2.3 Advanced BIOS Features setup By choosing the Advanced BIOS Features Setup op tion from the Initial Setup Screen menu, the sc reen below is displayed. This sample screen contains the manufacturer ’ s defaul t values for the PCI-687 1 Series.
PCI-6871 User’s Manual 38 4.2.4 Advanced Chipset Features setup By choosing the Advanced Ch ipset Features option from the Initi al Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer ’ s default va lues for the PCI-6871 Series.
39 Chapter 4 Award BIOS Setup 4.2.5 Integrated Peripherals Choosing the Integrated Peripheral s option from the Initial Setup Screen menu should prod uce the screen below . Here we see the manufacturer ’ s default values for the PCI-687 1 Series. 4.
PCI-6871 User’s Manual 40 4.2.7 PnP/PCI Configurations By choosing the PnP/PCI Configu rations option from the Initi al Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer ’ s default va lues for the PCI-6871 Series.
41 Chapter 4 Award BIOS Setup 4.2.9 Frequency/V oltage Control By choosing the Frequency/V oltage Control option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer ’ s defau lt values for the PCI-6871 Figure 4.
PCI-6871 User’s Manual 42 4.2.10 Load Optimized Defaults Load Optimi zed Defaults loads the default system values directly from ROM. If the stored record created by the Setup program should ever become corrupted (and therefore unusabl e), these defaults will load auto- matically when you turn th e PCI-6871 Series system on.
43 Chapter 4 Award BIOS Setup 3. At the “Confirm Password” prompt, retype the desired password, then press <Enter>. 4. Select Save to CMOS and EXIT , type <Y>, then <Enter>. T o Change Password 1. Choose the Set Password option from the CMOS Setup U tility main menu and press <Enter>.
PCI-6871 User’s Manual 44 4.2.13 Exit Without Saving Selecting this option and pressing <E nter> lets you exit the Setup pro - gram without recording any new values or changing old ones.
45 Chapter 5 PCI SVGA Setup 5 PCI SVGA Setup • Introduction • Installation of SVGA dri vers -for W indows 95/98/Me -for W indows NT/2000/XP • Further information CHAPTER.
PCI-6871 User’s Manual 46 Chapter 5 PCI SVGA Setup 5.1 Introduction The PCI-6871 has an onboard AGP flat panel/VGA interface. The speci- fications and features are described as follows: 5.1.1 Chipset The PCI-6871 uses a VIA T wisterT ch ipset from VIA T echnology Inc.
47 Chapter 5 PCI SVGA Setup 5.1.4 Dual/Simultaneous Display The PCI-6871 uses a VIA T wister VT8 606T LCD controller that is capa- ble of providing simu ltaneous dual view display of the sam e content on a flat panel and CR T .
PCI-6871 User’s Manual 48 5.2 Installation of the SVGA Driver Complete the followin g steps to install the SVGA driver . Follow the pro- cedures in the flow char t that apply to the operating syst em that you are using within your PCI-6871. 5.2.1 Installation for Windows 95 Step 1.
49 Chapter 5 PCI SVGA Setup Step 2. Choose the "Adapter" tab, then press the "Change..." button. Step 3. Press the "Have Disk" button.
PCI-6871 User’s Manual 50 Step 4. T ype in the path: D:slotPC6871VGAWin9x_Me Step 5. Select the highlighted item, and click the "OK" butt on.
51 Chapter 5 PCI SVGA Setup Step 6. "S3 GraphicsT wister" app ears under the adapter tab. Click the "Apply" button, then the "OK" b utton.
PCI-6871 User’s Manual 52 5.2.2 Installation for Windows 98/Me Step 1. Select "Start", "Settings", "Control Panel", "Display", and "Set- tings," then press the "Advanced.
53 Chapter 5 PCI SVGA Setup Step 2. Select “Adapter ,” then “ Change.”.
PCI-6871 User’s Manual 54 Step 3. Press “Next,” then “Display a list....” Step 4. Press the “Have disk...” button..
55 Chapter 5 PCI SVGA Setup Step 5. Insert the CD into th e CD-ROM drive. T ype in the path D:slotPC6871VGAWin9x_Me Then press “OK” Step 6. Select the highlig hted item, then click “OK.
PCI-6871 User’s Manual 56 Step 7. "S3 Graphics T wister"app ears under the adapter tab. Click the "Apply" button. Step 8. Press “Y es” to reboot.
57 Chapter 5 PCI SVGA Setup 5.2.3 Installation for Windows NT Step 1. Select "Start", "Settings", "Control Panel" and double click the "Display" icon. Note: Service Pack X (X = 3, 4, 5, 6,... ) must be installed fi rst, before you install the Windows NT VGA driver .
PCI-6871 User’s Manual 58 Step 2. Choose the "Settings" tab, and press the "Display T ype" button ..
59 Chapter 5 PCI SVGA Setup Step 3. Press the "Change..." button..
PCI-6871 User’s Manual 60 Step 4. Click the "Have Disk..." button. Step 5. T ype the path: D:slotPCVGAWinNT Press the "OK" button.
61 Chapter 5 PCI SVGA Setup Step 6. Select the highlighted item, and click the "OK" butt on. Step 7. Press "Y es" to proceed. Step 8.
PCI-6871 User’s Manual 62 5.2.4 Installation for Windows 200 0 Step 1. Select "System", "Settings", "C ontrol Panel" and double cli ck the "system" icon.
63 Chapter 5 PCI SVGA Setup Step 2. Choose the "V ideo Con troller (VGA Compatible)” button..
PCI-6871 User’s Manual 64 Step 3. Choose the "Drive" button, press “Update Driver ...” button..
65 Chapter 5 PCI SVGA Setup Step 4. Choose "Display a list of..." , then press “Next” button. Step 5. Choose “Display adapters”, press “Next” button.
PCI-6871 User’s Manual 66 Step 6. Click the “Have Disk” button. Step 7. T ype the path D:slotPC6871VGAW in2000 press the “OK” button. D:slotPCVGAWin2000.
67 Chapter 5 PCI SVGA Setup Step 8. Press “Finish" to reboot. 5.2.5 Installation for Windows XP Step 1. Select "System", "Settings", "C ontrol Panel" and double cli ck the "system" icon.
PCI-6871 User’s Manual 68 Step 2. Choose “Hardware” and “Device Manager”, press “OK” button..
69 Chapter 5 PCI SVGA Setup Step 3. Choose “V ideo Controller (VGA Compatible), press “OK” but- ton..
PCI-6871 User’s Manual 70 Step 4. Choose "Driver”, “Update Driver”, press “OK” button. Step 5. Choose “Install from a list.....” , press “Next”.
71 Chapter 5 PCI SVGA Setup Step 6. Choose “Don’t search. I will....”, press “Next” button. Step 7. Choose “Display adapters”, press “Next” button.
PCI-6871 User’s Manual 72 Step 8. T ype the path D:slotPC6871VGAW inXP then press “OK” button. Step 9. Choose “S3 Graphics T wister + S3 Hotkey” then press “Next ” button.
73 Chapter 5 PCI SVGA Setup Step 10. Press “Finish" to reboot. 5.3 Further Information For further information about the AGP/VGA installatio n in your PCI- 6871, includi ng driver updates, tro ublesh ooting guides and F AQ lists, visit the following web resources: VIA website: www .
PCI-6871 User’s Manual 74.
75 Chapter 6 Audio Setup 6 Audio Setup The PCI-6871 is equip p ed with an audio interface that records and plays back CD-quality audio. This chapter provides instruction s for installin g the software dr ivers included on the audio driver diskettes.
PCI-6871 User’s Manual 76 Chapter 6 Audio Setup 6.1 Introduction The PCI-6871 supports AC97 audio through the optional aud io module PCM-231A-00A1. 6.2 DOS utilities 6.2.1 VIA Sound Blaster Pro compatible set up program Please "Enable" the Sound Blaster setting in the BIOS before play ing Sound Blaster compatible DOS games.
77 Chapter 6 Audio Setup Step 3. The program will copy the re lative files into the directory which you assign. Next, the program will insert the fo llowing new line into the AUT OEXEC.BA T and copy the original AUTOEXEC.BA T to AUTOEXEC.VIA. C: VIAUDIOVIAUDIO.
PCI-6871 User’s Manual 78 Step 1. Click "Start" and select "S ettings". Click "Control Panel" and double-c lick "Add New Hard ware".
79 Chapter 6 Audio Setup Step 3. In the following Add New Hardw are W izard window , click "Next" for W indows to search for Plug and Play devices. Step 4. In the following Add New Hardware W izard window , select "No, the device isn't in the list.
PCI-6871 User’s Manual 80 Step 5. In the following Add New Hardware W izard window , select "No, I want to select..." and click "Next". Step 6. In the following Add New Hardware Wizard window , select "Sound, video and g ame controllers" and click "Next".
81 Chapter 6 Audio Setup Step 7. In the following Add New Hardw are W izard window , click "Have Disk...". Step 8. In the In stall From Disk windo w , click "Browse".
PCI-6871 User’s Manual 82 Step 9. In the Open window , select "D:slotPC6871Audi o98se_Me_2k_xpWIN95_98. Step 10. In the Instal l From Disk wind ow , click" OK ".
83 Chapter 6 Audio Setup Step 11. In the Select Device window , select "VIA PCI Audio Controller (WDM)" and click "OK". Step 12. In the A dd New Hardware Wizard window , click "Nex t".
PCI-6871 User’s Manual 84 Step 13. The Copying Files... window will appear . Step 14. In the Add New Hardware W izard window , cl ick "Finish".
85 Chapter 6 Audio Setup 6.3.3 Windows NT drivers Step 1. Click "Start" and select "S ettings". Click "Control Panel" and double-click "Multimedia". Step 2. In the Multimedia Propert ies window , select the "Devices" tab.
PCI-6871 User’s Manual 86 Step 3. In the Add window , select the "Unlisted..." item and click "OK". Step 4. When the Instal l Driver window appears, insert the utility disc into the CD-RO M drive. T ype: D:slotPC6871Audio W inNT Then click "OK".
87 Chapter 6 Audio Setup Step 5. In the Add Unlisted or Updated Driv er window , select the "VIA PCI Audio controller" ite m. Then click "OK".
PCI-6871 User’s Manual 88 6.3.4 Windows 2000 Drivers Step 1. Select “Syste m”, “Setting”, “Control Panel” and double click “system” icon.
89 Chapter 6 Audio Setup Step 3. Choose “Driver b utton, press “Update Driver” butt on. Step 4. Choose “Sound, video and game controll ers”, press “Next”.
PCI-6871 User’s Manual 90 Step 5. Click the “Have Disk...” button Step 6. T ype the path D:slotPC6871 Audio98se_Me_2k_xpWin2000 press the “ok” button.
91 Chapter 6 Audio Setup Step 8. Press “Next” button Step 9. Press “Finish” to reboot.
PCI-6871 User’s Manual 92.
93 Chapter 7 PCI Bus Ethernet Interface 7 PCI Bus Ethernet Inter- face This chapter provides information on Ethernet configuration. • Introduction • Installation of Ethern et drivers for W indows .
PCI-6871 User’s Manual 94 Chapter 7 PCI Bus Ethernet Interface 7.1 Introduction The PCI-6871 is equipped with a high perform ance 32-bit Ethernet chipset which is fully compliant wit h IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major network operating systems.
95 Chapter 7 PCI Bus Ethernet Interface 7.2.2 Installation for Windows 98 Step 1. a. Select "Start", "Settings". "Control Panel". b. Double click "Netwo rk". Step 2. a. Click "Add" and prepare to install network functions.
PCI-6871 User’s Manual 96 Step 3. a. Select the "Adapt er" item to add the Ethernet card. Step 4. a. Click "Have Disk" to install the driver .
97 Chapter 7 PCI Bus Ethernet Interface Step 6. a. Choose the "Realtek R TL8139(A/B/C/8130) PCI Fast Ethernet" item. b. Click "OK". Step 7. a. Make sure the configuratio ns of relative items are set correctly . b. Click "OK" to reboot.
PCI-6871 User’s Manual 98 7.2.3 Installation for Windows 200 0 Step 1. Open Device Manager ,.
99 Chapter 7 PCI Bus Ethernet Interface Step 2..
PCI-6871 User’s Manual 100 Step 3. Step 4..
101 Chapter 7 PCI Bus Ethernet Interface Step 5. Step 6..
PCI-6871 User’s Manual 102 Step 7. Step 8..
103 Chapter 7 PCI Bus Ethernet Interface Step 9. 7.2.4 Installation for Windows NT Step 1. a. Select "Start", "Settings", "Control Panel" b.
PCI-6871 User’s Manual 104 b. Click "Next" Step 3. a. Click "Select from list...".
105 Chapter 7 PCI Bus Ethernet Interface Step 4. Click “Have Disk.” Step 5. a. Insert th e Utility CD ROM b. Fill in the correct path: D:slotPC6871LAN813 9Cwinnt4 c.
PCI-6871 User’s Manual 106 Step 6. Check the highli ghted item , and click “OK.”.
107 Chapter 7 PCI Bus Ethernet Interface 7. Click “Next” to continue setup. Step 8. Choose the networking protocols, then click "Next".
PCI-6871 User’s Manual 108 Step 9. Select the correct Ne twork Services then click "Next" Step 10. Click “Next” to continue setup..
109 Chapter 7 PCI Bus Ethernet Interface 1 1. Click “Next” to st art the network. 7.3 Further information Realtek website: www .realtek.com.tw Intel websi te: www .
PCI-6871 User’s Manual 110.
111 Appx. A A Programming the W atchdog Timer The PCI-6871 is equipped with a watchdog timer that resets the CPU o r generates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned envi- ronments.
PCI-6871 Users’ Manual 112 Appendix A Programming the W atchdog Ti m e r A.1 Supported Input Timing Modes In order to program the watchdog tim er, you must write a program which writes I/O port address 443 (hex). The output data is a value of time inter- val.
113 Appx. A The following example sh ows how you might program the watchd og timer in BASI C: 10 REM Watchdog timer example program 20 OUT &H443, data REM Start and restart t he watchdog 30 GOSUB .
PCI-6871 Users’ Manual 114.
115 Appx. B B Installing PC/104 Modules This appendix gives instructions for installing PC/104 modu les. Appendix.
PCI-6871 Users’ Manual 116 Appendix B Installing PC/104 Modules B.1 Installing PC/104 Modules The PCI-6871's PC/104 connectors give you t he flexibility to at tach PC/ 104 modules. Installing these modules on the PCI-6871 is quick and simple. The fol - lowing steps show how to mount th e PC/104 modules: 1.
117 Appx. B Figure B.1: PC/104 m odule mounting diagram PCA-6751 Series Female PC/104 Mounting Support Male PC/104 module PCI-6871 Series PC/104 module.
PCI-6871 Users’ Manual 118 Figure B.2: PC/104 module dimensions (mm) (±0.1).
119 Appx. B T able B.1: PCI-6871 Series PC/104 connectors (CN16) Pin Signal (CN16) Number Row A Row B Row C Row D 0— — 0 V 0 V 1 IOCHCHK* 0 V SBHE* MEMCS16* 2 SD7 RESETDRV LA23 IOCS16* 3 SD6 +5 V .
PCI-6871 Users’ Manual 120 22 SA9 IRQ6 — — 23 SA8 IRQ5 — — 24 SA7 IRQ4 — — 25 SA6 IRQ3 — — 26 SA5 DACK2* — — 27 SA4 TC — — 28 SA3 BALE — — 29 SA2 +5 V — — 30 SA1 OSC — — 31 SA0 0 V — — 32 0 V 0 V — — *active low T able B.
121 Appx. C C Pin Assignments This appendix contains information of a detailed or specialized nature. It includes: • CPU Fan Power Connector • Ethernet 10/100Base-T Connector • Audio Conn ector .
PCI-6871 User’s Manual 122 Appendix C Pin Assignments C.1 CPU Fan Power Connector (F AN 1) C.2 Ethernet 10/100B ase-T Connector (CN15) T able C.1: C PU Fan Power Connec tor (F AN 1) Pin Signal 1 Fan speed signal input 2V c c 3G N D T able C.
123 Appx. C C.3 Audio Connector (CN10) T able C.3: Audio connecto r (CN10) Pin Signal Pin Signal 1 +5V 2 BitCLK 3D A T A i n 4 G N D 5 GND 6 SYNC 7 DA T A out 8 ACRST 9 +5V 10 reserved 4 14 15 3 16 13.
PCI-6871 User’s Manual 124 C.4 Main Power Connector (CN1 1) T able C.4: Main Po wer Connector (CN1 1) Pin Signal 1+ 5 V 2G N D 3G N D 4N / C 5N / C 6G N D 7+ 5 V.
125 Appx. C C.5 Keyboard and PS/2 Mouse Connector (CN25) T able C.5: Keyboard an d mouse connector (CN25) Pin Signal 1 KB CLOCK 2 KB DA T A 3M S C L O C K 4G N D 5 +5V (KB VCC) 6M S D A T A.
PCI-6871 User’s Manual 126 C.6 Floppy Disk Driv e Connector (CN6) T able C.6: Floppy Disk Drive Connec tor (CN6) Pin Signal Pin Signal 1 GND 2 DENSITY SELECT* 3G N D 4 N / C 5 GND 6 DRIVE TYPE 7 GND.
127 Appx. C C.7 IDE Hard Drive Conn ector (CN1, CN7) T able C.7: IDE HDD connector (CN1, CN7) Pin Signal Pin Signal 1 IDE RESET* 2 GND 3D A T A 7 4D A T A 8 5D A T A 6 6D A T A 9 7D A T A 5 8D A T A 1.
PCI-6871 User’s Manual 128 C.8 Parallel Port C onnector (CN2) T able C.8: Parallel Port Connec tor (CN2) Pin Signal Pin Signal 1S T R O B E * 2A U T O F D * 3D 0 4E R R 5 D1 6 INIT* 7 D2 8 SLCTINI* .
129 Appx. C C.9 HDD, PWR LED CON & WDT output (CN13) C.10 Reset Button Connector (CN8) T able C.9: HDD, PWR LED CON & WDT output (CN13) Pin Signal 1 WDT output 2G N D 3 power LED+ (+5V) 4 HDD LED + 5 power LED - (GND) 6 HDD LED - T able C.
PCI-6871 User’s Manual 130 C.1 1 USB Connector (CN20, CN28) C.12 LCD Inverter Backlight Connector (CN 27) T able C.1 1: USB Conn ector (CN20, CN28) Pin Signal Pin Signal 1+ 5 V 2+ 5 V 3U V - 4U V - 5U V + 6U V + 7 GND 8 GND 9 Chassis GND 10 N/C T able C.
131 Appx. C C.13 IR Connector (CN9 ) C.14 CRT Display Connector (CN1 2) T able C.13: IR Connector (CN9) Pin Signal 1 VCC (5 V) 2N . C . 3R X 4G N D 5T X T able C.
PCI-6871 User’s Manual 132 C.15 Flat Panel Connector (CN18) T able C.15: Flat Pa nel Connecto r (CN18) Pin Signal Pin Signal 1 VDDSAFE5 (+5v outpu t) 2 VDDSAFE5 (+5v output) 3 GND 4 GND 5 VDDSAFE3 (+3.
133 Appx. C C.16 Extended Flat Panel Di splay Connector (CN17) T able C.16: Extended Flat Pa nel Display Connector (CN17) Pin Signal Pin Signal 1 GND 2 GND 3P 2 4 4P 2 5 5P 2 6 6P 2 7 7P 2 8 8P 2 9 9 P30 10 P3 1 11 P 3 2 1 2 P 3 3 13 P34 14 P35 15 GND 16 GND 17 N/C 18 N/C 19 N/C 20 N/C Note: The model numb er of the CN 17 socket is DF13A-20DP-1.
PCI-6871 User’s Manual 134 C.17 LCD Signal Mapping T able C.17: LCD Signal Mapping Pin Name 16-bit DSTN 24-bit DSTN 18-bit TFT 24-bit TFT 36-bit TFT PD0 LB3 B0 R00 PD1 LB2 B1 R10 PD2 LB1 LB1 B0 B2 R.
135 Appx. C C.18 L VDS Connector (CN21) T able C.18: L VDS Conne ctor (CN21) Pin Signal Pin Signal 1 GND 2 GND 3 TX0+(Channel 1) 4 TX0+(Channel 2) 5 TX0-(Channel 1 ) 6 TX0-(Channel 2) 7 TX1+(Channel 1.
PCI-6871 User’s Manual 136 C.19 COM Port Connector (CN19, CN20) T able C.19: COM Port Connector (CN19, CN20 ) Pin Signal Pin Signal 1 RLSD1 (DCD1) 2 DSR1 3R X 1 4R T S 1 5T X 1 6 C T S 1 7D T R 1 8R.
137 Appx. C C.20 CompactFlash Card Connector (CN28) T able C.20: CompactF lash Card Connector (CN28 ) Pin Signal Pin Signal 1G N D 2 D 0 3 3 D04 4 D05 5 D06 6 D07 7* C S 0 8 A 1 0 9 *A T A SEL 10 A09 .
PCI-6871 User’s Manual 138 C.21 A TX Power Feature Connector (CN3) C.22 LCD Backlight Connector (CN24) T able C.21: A TX Power Featur e Connector (CN3) Pin Signal 1 5VSB (Stand by voltage) 2G N D 3P S .
139 Appx. C C.23 External Keyboa rd Connector (CN26) T able C.23: External Keyboar d Connector (CN26) Pin Signal 1C L K 2D A T A 3N C 4G N D 5+ 5 V.
PCI-6871 User’s Manual 140.
141 Appx. D D System Assignments This appendix contains information of a detailed n ature. It inclu des: • System I/O ports • 1st MB memory map • DMA channel assignments • Interru pt assignmen.
PCI-6871 User’s Manual 142 Appendix D System Assignments D.1 System I/O Ports T able D.1: System I/O ports Addr . range (Hex) Device 000-01F D MA controller 020-021 Interrupt controller 1, master 04.
143 Appx. D D.2 1st MB memory map D.3 DMA channel assignments T able D.2: 1st MB memory map Addr . range (Hex) Device F0000h - FFFFFh System ROM *CC000h - EFFFFh Unused (reserved for Ethernet ROM) C00.
PCI-6871 User’s Manual 144 D.4 Interrupt assignments T able D.4: Interrupt ass ignments Interrupt# Interrupt source IRQ 0 Interval timer IRQ 1 Keyboard IRQ 2 Interrupt from controller 2 (cascade) IR.
145 Appx. E E Optional Extras for the PCI-6871 Appendix.
PCI-6871 User’s Manual 146 E.1 Optional USB cable (CN20) Optional USB cable (2.0mm ) part no.: 1703100260 E.2 A TX Power Control Cable part no.: 17032 00100 E.
An important point after buying a device IBM LCD/LVDS/LAN (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought IBM LCD/LVDS/LAN yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data IBM LCD/LVDS/LAN - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, IBM LCD/LVDS/LAN you will learn all the available features of the product, as well as information on its operation. The information that you get IBM LCD/LVDS/LAN will certainly help you make a decision on the purchase.
If you already are a holder of IBM LCD/LVDS/LAN, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime IBM LCD/LVDS/LAN.
However, one of the most important roles played by the user manual is to help in solving problems with IBM LCD/LVDS/LAN. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device IBM LCD/LVDS/LAN along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
