Instruction/ maintenance manual of the product Q1-DC hussman
Go to page of 35
Q1-DC DELI SERVICE CASE P/N Q1-DC-0508 INST ALLA TION & OPERA TION GUIDE /CHINO Q1-DC DELI SERVICE CASE REV . 0508 Installation & Operation Manual.
Q1-DC-0508 2 /CHINO A publication of HUSSMANN ® Chino 13770 Ramona Avenue • Chino, California 91710 (909) 628-8942 F AX (909) 590-4910 (800) 395-9229 Keep this booklet with the case at all times for future reference. General Instructions T able of Contents General Instructions.
Rev . 0508 3 Cut and Plan Views 45 13/16" 45" 34 1/8" 11 7/8" 35" 11 5/16" 17 1/8" 8" 9 3/4" 24 3/8" 15 7/8" 27 3/4" 6 7/8" 11" 29.
Q1-DC-0508 4 5. Apply liberal bead of case joint sealant (butyl) to rst case. Sealant area is shown using a dotted line in illustration in Step 8. Apply heavy amount to cover entire shaded area.
Rev . 0508 5 Plumbing W aste Outlet and P-TRAP The waste outlet is located off the center of the case on one side allowing drip piping to be run lengthwise under the xture. A 1-1/2” P-TRAP and threaded adapter are supplied with each xture. The P-TRAP must be installed to prevent air leakage and insect entrance into the xture.
Q1-DC-0508 6 Electronic Expansion V alve (Optional) A wide variety of electronic expansion valves and case controllers can be utilized. Please refer to EEV and controller Hussmann’s information sheet. Sensors for ele ctron ic expan sion valv es will be inst alled on the coil inle t, coil outlet, and in the discharge air .
Rev . 0508 7 Wiring and Serial Plate Amperage Fi eld Wi ring mus t be si zed fo r com pon ent am pere s st ampe d on the serial plate. Actual ampere draw may be less than spec ied. Fiel d wirin g from the refr igerati on con trol panel to the merch andiser s is requ ired for refr igerati on therm ostats.
Q1-DC-0508 8 7. Keep the service doors closed (when applicable). Refrigeration performance will be seriously affected if left open for a prolonged period of time. 8. Avoid the use of supplemental ood or spot lighting. Display light intensity has been designed for maximum visibility and product life at the factory .
Rev . 0508 9 Non-Glare Glass The high optical clarity of this glass is possible due to spec ial coat ings on the glass surface itself . T o pres erve this coating and the optical clarity , keep the glass clean. W ater is the only solut ion recom mended for use in cleanin g non-glare glass.
Q1-DC-0508 10 Maintenance FOR PROMPT SERVICEHave case Model and Serial Numberready! This information is located on thenameplate of the unit. BEFORE SERVICING ALWAYS DISCONNECT ELECTRICAL POWER AT THE MAIN DISCONNECT WHEN SERVICING OR REPLACING ANY ELECTRICAL COMPONENT.
Rev . 0508 1 1 Electrical Wiring Diagrams Q1-DC Q1-DC-4R 4’ W1750001 Deli-Curve Glass Q1-DC-6R 6’ W1750002 RJ-45,Ledge Lights Q1-DC-8R 8’ W1750003 12’ W1750005 Q1-DC Q1-DC-4R 4’ W1750006 Q1-.
Q1-DC-0508 12 Wiring Diagrams DATE: PROJECT TIT L E: DWG #: DRAW N BY: PRODUCTION ORDER #: DRAWING T ITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCATION: D.QUAN --- PAGE OF HUSSMAN N CORPORATION 13770 RAMONA AVE NUE CHINO, CA.
Rev . 0508 13 DATE: PROJECT TIT L E: DWG #: DRAW N BY: PRODUCTION ORDER #: DRAWING T ITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCATION: D.QUAN --- PAGE OF HUSSMAN N CORPORATION 13770 RAMONA AVE NUE CHINO, CA.91710 (909) 590-4910 LIC.
Q1-DC-0508 14 DATE: PROJECT TIT L E: DWG #: DRAW N BY: PRODUCTION ORDER #: DRAWING T ITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCATION: D.QUAN --- PAGE OF HUSSMAN N CORPORATION 13770 RAMONA AVE NUE CHINO, CA.91710 (909) 590-4910 LIC.
Rev . 0508 15 DATE: PROJECT TIT L E: DWG #: DRAW N BY: PRODUCTION ORDER #: DRAWING T ITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCATION: D.QUAN --- PAGE OF HUSSMAN N CORPORATION 13770 RAMONA AVE NUE CHINO, CA.91710 (909) 590-4910 LIC.
Q1-DC-0508 16 DATE: PROJECT TIT L E: DWG #: DRAW N BY: PRODUCTION ORDER #: DRAWING T ITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCATION: D.QUAN --- PAGE OF HUSSMAN N CORPORATION 13770 RAMONA AVE NUE CHINO, CA.91710 (909) 590-4910 LIC.
Rev . 0508 17 DATE: PROJECT TIT L E: DWG #: DRAW N BY: PRODUCTION ORDER #: DRAWING T ITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCATION: D.QUAN --- PAGE OF HUSSMAN N CORPORATION 13770 RAMONA AVE NUE CHINO, CA.91710 (909) 590-4910 LIC.
Q1-DC-0508 18 DATE: : # G W D : E L T I T T C E J O R P DRAWN BY: PRODUC TION ORDER #: DRAWI NG TITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCA T ION : D.QUAN --- PAGE OF HUSSMANN CORPORATION 13770 RAMONA AVENUE CHINO, CA.
Rev . 0508 19 DATE: PROJECT TIT L E: DWG #: DRAW N BY: PRODUCTION ORDER #: DRAWING T ITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCATION: D.QUAN --- PAGE OF HUSSMAN N CORPORATION 13770 RAMONA AVE NUE CHINO, CA.91710 (909) 590-4910 LIC.
Q1-DC-0508 20 DATE: PROJECT TIT L E: DWG #: DRAW N BY: PRODUCTION ORDER #: DRAWING T ITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCATION: D.QUAN --- PAGE OF HUSSMAN N CORPORATION 13770 RAMONA AVE NUE CHINO, CA.91710 (909) 590-4910 LIC.
Rev . 0508 21 DATE: PROJECT TIT L E: DWG #: DRAW N BY: PRODUCTION ORDER #: DRAWING T ITLE: DATE: REVISIONS: : Y B D E K C E H C : N O I T P I R C S E D : # BY: FILE LOCATION: D.QUAN --- PAGE OF HUSSMAN N CORPORATION 13770 RAMONA AVE NUE CHINO, CA.91710 (909) 590-4910 LIC.
Q1-DC-0508 22 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TI TLE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA.
Rev . 0508 23 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TIT LE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA.
Q1-DC-0508 24 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TI TLE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA.
Rev . 0508 25 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TI TLE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA.
Q1-DC-0508 26 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TI TLE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA.
Rev . 0508 27 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TI TLE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA.
Q1-DC-0508 28 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TI TLE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA.
Rev . 0508 29 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TI TLE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA. 91710 (909)-590-4910 Lic.#: 644406 REVISIONS: #: DESCRIPTION: CHECKED BY: BY: FILE LOCATION: JESSE RIOS PAGE OF ? L CIRCUIT #1 EVAP FAN MOTOR (4)0392457 .
Q1-DC-0508 30 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TIT LE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA.
Rev . 0508 31 DATE: PROJECT TIT LE: DRAWING #: DRAW N BY: PRODUCTION ORDER #: DRAWING TI TLE: DATE: Hussmann Corporation, Int'l. 13770 Ramona Avenue Chino, CA.
Q1-DC-0508 32 Appendices Appendix A. - T emperature Guidelines - Refrigerated The refrigerators should be operated according to the manufacturer ’ s published engineering specications for en teri ng ai r te mper atu res fo r spe cic equ ipm ent app lica tio ns.
Rev . 0508 33 Appendices (Cont'd) 1.1 The following recommendations are made for the purpose of arriving at easily taken and understood data which, coupled with other observations, may be used to.
Q1-DC-0508 34 Appendices (Cont'd) 1.1 Cleaning of non frozen food equipment should include a weekly cleaning of the food compartment as a minimum to prevent bacteria growth from accumulating. Actual use and products may dictate more frequent cleaning.
The MODE L NAM E and SERI AL NUMB ER is requ ired in ord er to prov ide you with the correct parts and information for your particular unit. They can be found on a small metal plate on the unit.
An important point after buying a device hussman Q1-DC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought hussman Q1-DC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data hussman Q1-DC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, hussman Q1-DC you will learn all the available features of the product, as well as information on its operation. The information that you get hussman Q1-DC will certainly help you make a decision on the purchase.
If you already are a holder of hussman Q1-DC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime hussman Q1-DC.
However, one of the most important roles played by the user manual is to help in solving problems with hussman Q1-DC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device hussman Q1-DC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
